Search results for "dryer belts"

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406105 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP697772 Dryer Blower Wheel - Compatible with Whirlpool, Maytag, Kenmore, Amana Product Description Restore your dryer’s performance with the WP697772 Blower Wheel. This genuine OEM replacement blower wheel attaches to the drive motor shaft, circulating air through the drum and out the exhaust vent for efficient drying. Designed for Whirlpool, Maytag, Kenmore, Amana, and other dryers, it fixes issues like reduced airflow, long drying times, or noisy operation. Note: Includes one blower wheel (clamp not included). Note reverse threads and take photos of disassembly. Order a new wheel if removing the old one, as it may break. Replaces part numbers: WP697772, 697772, PD00003053, EAP11743811, AP6010627, PS11743811.  Compatibility: Compatible with models including but not limited to: Whirlpool: MEDB835DW, WED5620HW, MED7230HW, WED8000DW, WED8500DC Maytag: MEDC700VW0, MGDB835DW Kenmore: 110.67862790, 110.87872600 Amana: NED4655EW Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, KitchenAid dryers. 💨 Specifications: OEM white plastic blower wheel, 7-9/16" diameter x 3" deep, with left-handed threads for reliable airflow. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, 1/2" ratchet, 7/16" wrench; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves reduced airflow, long drying times, noisy operation, or overheating. Installation Notes: Safety First: Unplug the dryer or shut off the circuit breaker before installation to avoid electrical shock. Old wheel may break during removal; order a replacement in advance. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 3406107 Dryer Door Switch – Replaces WP3406107 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Ensure your dryer starts safely and operates correctly with the XPARTCO 3406107 Dryer Door Switch. This high-quality aftermarket replacement detects when the dryer door is closed, enabling the motor to run and heat to activate. A defective switch can prevent your dryer from starting or cause it to stop mid-cycle. Replacing it with this reliable XPARTCO switch restores normal operation and dependable performance. Replaces Part Numbers WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, PS11741701. Compatibility This replacement door switch fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.60902990, and Maytag MEDC200XW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Engineered to match OEM safety and electrical performance 🚪 Restores Start Function – Ensures dryer runs only when the door is fully closed 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ Quick Installation – Simple plug-in wiring and snap-in mounting 🛡️ Fixes Common Issues – Solves dryer not starting, shutting off mid-cycle, or running with door open 📐 Product Specification Part Number: 3406107 Component Type: Dryer Door Switch Assembly Material: Plastic body with metal actuator lever and 3-pin terminal Mounting: Snap-in installation behind front panel Electrical Rating: 15A / 125-250V AC Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and open the dryer door. Remove the top or front panel (depending on model). Unplug the old switch’s wire connectors. Press the locking tabs and remove the old switch. Install the new XPARTCO 3406107 switch, reconnect wires, and secure panels. Restore power and test dryer start function. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s start function — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

WP4391960 Genuine OEM Whirlpool Dryer Heating Element The WP4391960 is a Genuine OEM Whirlpool replacement dryer heating element used in older-generation Whirlpool-family electric dryers, including Whirlpool, Kenmore, Roper, Estate, Amana, and Admiral models — particularly the LE, EL, and early LG series dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around ceramic insulators inside a steel housing that generates heat when electrical current passes through it. When the coil burns through, the circuit opens and the dryer produces no heat. A shorted coil that contacts the housing is a fire hazard and requires immediate replacement. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated 5200W / 240V with 1/4" male spade terminals. Note: this element uses 1/4" terminals — different from the 5/16" terminals on the 279838 and WP3387747 elements. The wire kit and wire nuts (part 279457) are no longer included with this element and must be ordered separately if the original wires are damaged. It consolidates a very large list of older cross-reference numbers including 4391960, 2013, 279247, 279248, 279410, 279411, 696579, 696326, 697290, 786077, AP6009347, PS11742505, and dozens more. Installs in 20–45 minutes with basic hand tools. Quick Answer The WP4391960 Genuine OEM Whirlpool Dryer Heating Element fixes older Whirlpool-family electric dryers (LE, EL, early LG series) that produce no heat, run too hot, or take too long to dry. 5200W / 240V, 1/4" male spade terminals (not 5/16"). Wire kit 279457 sold separately — not included. Genuine OEM. Replaces 4391960, 2013, 279247, 279248, 279410, 279411, 696579, AP6009347, PS11742505, and many more. Compatible with older Whirlpool, Kenmore, Roper, Estate, Amana, and Admiral electric dryers. Common Problems This Part Fixes Dryer produces no heat — element coil burned through Dryer takes much longer than normal to dry a load Dryer tumbles normally but produces no heat at all during the cycle Dryer overheating or running continuously — coil shorted to housing (fire hazard) Visible break, burn spot, or collapsed section in the heating coil Burning smell during operation — arcing at a weak point in the coil Dryer trips the circuit breaker when the heat cycle is selected Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: WP4391960, 4391960, 2013, 279218, 279247, 279248, 279410, 279411, 279455, 279598, 279698, 3367, 337378, 337430, 339655, 340468, 348775, 349542, 349543, 349545, 349546, 660933, 660982, 685182, 685942, 689805, 689980, 690241, 690983, 691724, 692758, 693061, 693062, 693297, 693298, 693299, 693300, 695182, 696324, 696326, 696579, 697290, 786077, 8218, 8700-599, WP4391960VP, AWP47415, DE177, DE193, DE195, DE698, EAP11742505, ER4391960, AP6009347, PD00002385, PS11742505, TJ90DE698. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select older-generation electric dryers only from the following brands: Whirlpool electric dryers — LE, EL, and early LG/LER series (older models) Kenmore / Sears electric dryers — older 110-series models (Whirlpool-built) Roper electric dryers Estate electric dryers Amana electric dryers (older models) Admiral electric dryers Important: The WP4391960 uses 1/4" male spade terminals — different from the 5/16" terminals on the 279838 and WP3387747 elements. Verify your existing element's terminal size before ordering. Also: the wire kit (part 279457) is no longer included with this element — order separately if needed. Always verify your exact model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for older Whirlpool-family electric dryers — nickel-chromium resistance coil Rated 5200W / 240V — correct electrical specifications for compatible older-generation dryer models 1/4" male spade terminals — different from the 5/16" terminals on 279838 and WP3387747; verify before ordering Consolidates over 50 older cross-reference part numbers into a single current OEM part Wire kit (part 279457) no longer included — order separately if original wires are damaged Do not touch the element coil with bare hands — skin oils cause premature burnout Compatible with Whirlpool LE/EL series, Kenmore older 110-series, Roper, Estate, Amana, and Admiral electric dryers DIY repair — installs in 20–45 minutes with basic hand tools Product Specifications Part Number WP4391960 Part Type Dryer Heating Element (Electric) Condition Genuine OEM Application Older-Generation Electric Dryers (LE, EL, early LG/LER series) Wattage 5200W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals 1/4" male spade terminals (not 5/16") Wire Kit Not included — order part 279457 separately if needed Handling Note Do not touch coil wire — skin oils cause premature burnout Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Coil Wire Disconnect power before beginning. Remove the back panel of the dryer to access the heating element housing. On older LE-series Whirlpool models, the element housing is mounted at the lower rear of the dryer and may have a top panel over the housing that must be removed before the element can be freed. Photograph all wiring before disconnecting. Note: the element's wires and wire nuts (279457 kit) are no longer included with the WP4391960 — if your existing wires are in good condition, reuse them; if damaged, order 279457 separately before beginning. Do not touch the new element's coil wire at any point — skin oils create hot spots that will prematurely burn the element. Disconnect the old element wires, unscrew the housing mounting screws, and remove the old element. Install the new WP4391960 in the same orientation, reconnect wiring, reinstall the housing, and restore power. Run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What is the difference between WP4391960 and 279838 or WP3387747? All three are Genuine OEM Whirlpool dryer heating elements, but for different generations of dryers and with different terminal sizes. The WP4391960 (5200W, 1/4" spade terminals) is for older-generation Whirlpool LE/EL series and early Kenmore dryers. The 279838 (5400W, 5/16" terminals) is for standard-capacity mid-generation Whirlpool-family dryers. The WP3387747 (5200W, 5/16" terminals) is for newer higher-capacity models like the Duet, Cabrio, HE, and GEW/GEQ series. The terminal size difference is important — the WP4391960 uses 1/4" spade terminals, while the other two use 5/16" terminals. Always verify your model number before ordering. Why does this element have so many cross-reference part numbers? The WP4391960 consolidates a very large number of older Whirlpool heating element part numbers that were used across many different model runs over the years. As Whirlpool refined the design and standardized parts across its lineup, it consolidated these older numbers into the current WP4391960. If your dryer's parts diagram shows any of the hundreds of older cross-reference numbers listed above, the WP4391960 is the correct current replacement. Why is the wire kit (279457) not included? Whirlpool changed the packaging of this part during a production revision and no longer includes the wire kit and wire nuts that were previously bundled with the element. If your existing element wires are in good condition, you can reuse them — carefully transfer each wire to the corresponding terminal on the new element, maintaining the original connections. If any wires are burned, melted, or damaged, order part 279457 (wire kit) separately before beginning the repair. How do I test if the heating element has failed? Unplug the dryer and disconnect the element terminals. Set your multimeter to continuity or resistance mode. A working 5200W/240V element shows a resistance reading — typically around 9–12 ohms. No continuity (open circuit) means the coil has burned through. Also test each terminal individually to the metal housing frame — if continuity exists between a terminal and the housing, the element is shorted to ground and must be replaced immediately as a fire hazard. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible older-generation Whirlpool, Kenmore, Roper, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

8540101CM Washer Drive Belt Washing machine inner tub drive belt 6 Rib, 51.33" Description: The Drive Belt is a replacement for specific Whirlpool, Maytag, Kenmore washer models. It transmits power from the washer motor to the tub, causing it to rotate during wash and spin cycles Causes of a worn drive belt can include repetitive cycles over years of use. The belt undergoes stress each time the tub is set in motion. Damage from slipping off pulleys during operation can also affect the belt. Replaces Part NumbersWP8540101, 8540101, 8540348, AP6013037, PS11746258 This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

WE11X203 Dryer Genuine OEM Heater Restring Coil Kit  Dryer heating element restring kit. This kit replaces the existing heating coil in your dryer.  This Heater restring Coil Replaces WE11X103 Heater Restring Coil.  The diameter of the coil is 1/2" OD it stretches around the pan over the ceramic insulators.   Replaces Part Numbers:WE11X203, AH265619, AP2620176, DE333, EA265619, K35-408, PS265619, WE11X0203, WE11X103C   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279311 Genuine OEM Dryer Igniter Kit and Bracket - Compatible with Whirlpool, Maytag, Kenmore Product Description Restore your gas dryer’s heating performance with the 279311 Genuine OEM Dryer Igniter Kit and Bracket. This Whirlpool-manufactured kit includes a silicon carbide igniter, ceramic holder, bracket, wire leads, and plug, designed to ignite the gas burner in select Whirlpool, Maytag, Kenmore, and other compatible gas dryers. It addresses issues like no heat, intermittent heating, or prolonged drying times, ensuring efficient operation. Handle with care, as the igniter is fragile. Note: Includes (1) igniter kit with bracket, wire leads, and plug. Disconnect power and gas supply before installation. Verify compatibility with your dryer model. Replaces part numbers: 279311, 239233, 239300, 239302, 26000279311, 279185, 279311VP, 338899, 338900, 3389895, 340607, 3415, 343128, 41-311, 6-85211, 660991, 685211, 686590, 687399, 691039, 8113, 99912719, AH334180, DE351, DE354, DE363, PD00002344, EAP334180, EA334180, K35-166, AP3094138, PS334180. Compatibility: Compatible with select gas dryer models, including but not limited to: Whirlpool: CG1751XWN0, CG1751XWW0, CG2101XMW0, CG2501XMW0, WGD4910XQ1 Maytag: MGDX655DW, MGDC415YW0, MGD6000BW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Amana: NGD4655EW0 Roper: RGD4515EW0 Common models: Whirlpool WGD4815EW, Maytag MGD3500FW0, Kenmore 110.97561601 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, Roper, and other gas dryers. 🔧 Specifications: Genuine OEM Whirlpool silicon carbide igniter with ceramic holder, bracket, wire leads, and plug. 💪 Reliable Performance: Ignites gas burner for consistent heating, ensuring efficient drying. 🛠️ Easy Installation: Requires a screwdriver, nut driver, and pliers; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves no heat, intermittent heating, thermal fuse tripping, or prolonged drying times. Product Specification Part Number: 279311 Component Type: Gas dryer igniter kit Material: Silicon carbide igniter with ceramic holder and metal bracket Operating Conditions: Suitable for gas dryer burner assemblies, 120V Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today! Add to cart now for a reliable fix!

Read more less

🚪 EXP571 Dryer Door Catch This Dryer Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number Exp571. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. ✅ Key Features: High-quality aftermarket replacement Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: WP71002106, WP3389441, 3389441, 71002106, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AP2042209, PS266896, 131658800, AP2107362, PS418433, 5307521419, 10690002, 10690001. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Whirlpool✔️ Maytag✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic ? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the EXP71 dryer door catch from parts-o-matic.com, and enjoy fast, free U.S. shipping!

Read more less

12238200001084 Genuine OEM Midea Dryer Bearing House Assembly (Drum Rear Bearing) The 12238200001084 is a Genuine OEM Midea replacement bearing house assembly compatible with select Midea, Criterion, and Insignia electric and gas dryers, including the CDE41N1AW series. The bearing house assembly is mounted at the rear of the drum and houses the bearing that the rear drum shaft rotates within, supporting the back of the drum and allowing it to spin smoothly. Unlike front-mounted slide rollers used on some dryer platforms, this Midea design uses a rear bearing housing assembly to carry the load at the back of the drum. When the bearing house assembly wears out — typically from age, lack of lubrication, or accumulated lint and debris — the drum no longer spins smoothly on its rear support, resulting in grinding, rumbling, or squealing noise, increased drum drag, and in advanced cases, visible wobble or binding of the drum during rotation. As a Genuine OEM part manufactured by Midea to factory specifications, the 12238200001084 is a complete bearing house assembly designed as a direct replacement for the original equipment component. Installs in 45–60 minutes with basic hand tools, as drum removal is required. Quick Answer The 12238200001084 Genuine OEM Midea Dryer Bearing House Assembly fixes Midea, Criterion, and Insignia dryers with grinding, rumbling, or squealing noise from the rear of the drum, increased drum drag, or visible drum wobble. Mounted at the rear of the drum — houses the bearing the rear drum shaft rotates within. Genuine OEM. Compatible with Midea CDE41N1AW and related Midea electric dryer platform models. Requires drum removal to access — a more involved repair than a front roller swap. Common Problems This Part Fixes Loud grinding or rumbling noise from the rear of the drum during the drying cycle Squealing or squeaking noise as the drum rotates — worn or dry bearing surface Increased drag or resistance felt when manually rotating the drum by hand Drum wobbling or binding during rotation — worn bearing no longer providing stable support Excessive vibration during the drying cycle Visible wear, cracking, or lint/debris buildup in the bearing house area Drum scraping against the rear bulkhead due to lost bearing support Replaces Part Numbers This bearing house assembly directly replaces the following part number: 12238200001084, AP7154967, PS18167713 This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering. Compatibility This bearing house assembly is compatible with select Midea, Criterion, and Insignia dryers, including: Midea CDE41N1AW electric dryer Midea MLE series electric dryers (select models — same drum/bearing platform) Criterion electric dryers built on the Midea platform (select models) Insignia electric dryers built on the Midea platform (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Complete bearing house assembly — supports the rear of the drum and allows smooth, quiet rotation Houses the bearing that the rear drum shaft rotates within — a sealed-style design intended to resist lint intrusion Direct replacement for the original equipment bearing house assembly Compatible with Midea CDE41N1AW and related Midea, Criterion, and Insignia electric dryer platform models Installs in 45–60 minutes with basic hand tools (drum removal required) Product Specifications Part Number 12238200001084 Part Type Dryer Bearing House Assembly (Drum Rear Bearing) Condition Genuine OEM Application Electric Dryers (Midea platform) Location Rear of drum — houses rear drum shaft bearing Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum. Take a photo of the belt routing before disconnecting the drive belt from the idler pulley. Carefully lift the drum out of the cabinet and set it aside on a padded surface. Locate the bearing house assembly mounted at the rear bulkhead where the drum's rear shaft was seated. Remove the mounting screws or clips securing the old bearing house assembly and pull it free. Clean any accumulated lint or debris from the mounting area before installing the new part. Install the new 12238200001084 bearing house assembly in the same position and secure the mounting hardware. Reinstall the drum, re-route and reconnect the drive belt, and reassemble the front and top panels. Restore power and run a test cycle to confirm the drum rotates smoothly and quietly. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the bearing house assembly do? The bearing house assembly is mounted at the rear bulkhead of the dryer and houses the bearing that the rear drum shaft rotates within. It supports the back of the drum as it spins, allowing smooth, low-friction rotation throughout the drying cycle. Unlike dryer platforms that use front-mounted slide rollers or felt seals for drum support, this Midea design relies on a dedicated rear bearing housing to carry the structural load at the back of the drum. As the bearing wears, friction increases, leading to noise, drag, and eventually wobble or binding if left unaddressed. How do I know if the bearing house assembly has failed versus another component? A grinding, rumbling, or squealing noise specifically tied to drum rotation — rather than the blower motor or idler pulley — and noise that changes pitch as the drum speeds up or slows down often points to the rear bearing. With the dryer unplugged and the drum exposed (front panel removed), try rotating the drum by hand: if you feel noticeable resistance, grinding, or grittiness compared to a smooth, free rotation, the bearing house assembly has likely worn out and needs replacement. Why does this repair require removing the drum? The bearing house assembly is mounted at the rear bulkhead behind the drum, supporting the drum's rear shaft from the inside. There is no way to access this component without first removing the front panel and lifting the drum out of the cabinet. This makes it a more involved repair than swapping a front-accessible part like a belt or idler pulley, but it follows the same general dryer disassembly procedure used for accessing other internal drum components. Should I inspect other components while the drum is out? Yes — since the drum must already be removed to access the bearing house assembly, this is an excellent opportunity to inspect the drive belt, idler pulley, and any felt seals or gaskets around the drum opening for wear. Components in this drum drive system tend to wear together, and addressing multiple worn parts in a single repair session helps avoid a near-term repeat teardown. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same bearing house assembly installed in compatible Midea, Criterion, and Insignia electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4 Pack - XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 - Pack Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WH01X10302 Washer Genuine OEM Drive Belt Replaces Part Numbers: WH01X10302, WH01X10353, 175D5131P003, AH1482278, EA1482278, AP3968432, PS1482278. Description: This Drive Belt is a Genuine OEM part for specific GE washing machine models. This belt is responsible for connecting the motor to the drum, enabling the drum to spin during the wash and spin cycles. Common causes of a bad drive belt can include regular wear and tear from normal usage, overloading the washing machine, or exposure to harsh conditions that cause the belt to crack or fray. When the drive belt is compromised, it can affect the overall performance of the washing machine.

Read more less