W11025156 Genuine OEM Whirlpool Dryer Heating Element
The W11025156 is a genuine Whirlpool OEM heating element for Whirlpool, Kenmore, and Maytag electric dryers. This element is the source of virtually all the heat in the dryer: it converts electrical energy into heat, which the blower then circulates through the drum to dry your clothes. Even heat distribution from a properly functioning element is what keeps drying times consistent and prevents the dryer from having to run longer cycles to compensate.
Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. Symptoms of a failing element include clothes taking too long to dry, clothes coming out cold, or the dryer not heating at all. This part is also essential for preventing overheating, since a properly functioning element operates within its designed parameters rather than drawing excess current trying to compensate for a partial failure. It directly replaces W10608823.
Quick Answer
The W11025156 Genuine OEM Whirlpool Dryer Heating Element fixes Whirlpool, Kenmore, and Maytag electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Replaces W10608823. Before replacing, clean out or inspect your exhaust venting — restricted airflow is a common cause of premature heating element failure, and a fresh element installed into a clogged system is likely to fail again.
Common Problems This Part Fixes
Dryer runs a full cycle but produces no heat at all
Dryer produces some heat, but not enough to dry clothes properly
Drying times that have gotten noticeably longer than they used to
Clothes coming out cold or barely warm at the end of a cycle
Visible break or burned-through section in the heating coil
Dryer not drying laundry despite completing a normal cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer heating element directly replaces the following OEM and cross-reference part numbers:
W11025156, W10608823, 4461512, W10608823, AP6037386, AWP42261, EAP11770230, PD00034419, PS11770230.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore and Maytag dryers built on the same platform, including model numbers such as:
MEDB855DC2, MEDB955FC1, MEDB955FW1 (Maytag)
YWED8000DW1, YWED8500DW1, WED9500EC0, WED9500EW0, WED8700EC2
Kenmore 11061632610, 11061632611, 11061632612, 11061633610, 11061633611
Kenmore 11068132411, 11068132412, 11068132413, 11068133411, 11068133412, 11068133413
Kenmore 11069132411, 11069132412, 11069132413, 11069133411, 11069133412, 11069133413
Kenmore 110C61633610, 110C68132413
Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified coil design and electrical rating
Converts electrical energy into heat, circulated through the drum by the blower
Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil
Ensures even heat distribution for consistent drying performance
Direct drop-in replacement — no modification required
Replaces W10608823
Compatible with Whirlpool, Kenmore, and Maytag electric dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11025156
Part Type
Dryer Heating Element
Condition
Genuine OEM
Brand
Whirlpool
Function
Generates heat to dry clothes, circulated through the drum
Repair Difficulty
Medium — basic electrical skills and dryer panel disassembly required
Quantity
1 heating element
Compatible Brands
Whirlpool, Kenmore, Maytag
Installation Notes
⚠️ Unplug Dryer Before Starting — Clean The Vent While You Have The Panel Open Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the back panel: a 1/4" ratchet with a 5/16" socket handles most of the screws, and using a socket adapter on a screw gun can speed up removing and reinstalling the panel, since there are several screws to deal with. With the panel off, locate the heating element in the duct housing. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new W11025156 in the same position, reconnect the wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" ratchet, 5/16" socket, work gloves.
Frequently Asked Questions
My dryer runs a full cycle but the clothes are still wet. Is this the heating element?
It's a strong possibility, especially if you've noticed drying times gradually getting longer before the dryer stopped heating altogether. One customer described exactly this symptom — "dryer not drying laundry" — and resolved it with this exact replacement element.
Do I need any special tools for this repair?
Just basic hand tools. A 1/4" ratchet with a 5/16" socket handles the back panel screws on most models. Using a socket adapter on a screw gun can speed up the process, since there are several screws to remove and reinstall on the back panel alone.
Why does the listing recommend cleaning the vent during this repair?
Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original coil design and electrical rating of the heating element originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WP3387749 Dryer Genuine OEM Heating Element – Compatible with Whirlpool, Kenmore, Maytag Dryers
Product Description
Restore your dryer’s heating performance with the WP3387749 Dryer Genuine OEM Heating Element. This factory-approved replacement part generates the heat needed to dry laundry efficiently. A failed heating element may cause your dryer to run but not heat, take longer to dry clothes, or shut down during cycles. Replacing it with this genuine OEM part ensures safe operation and long-lasting performance.
Replaces Part Numbers
WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418.
Compatibility
This heating element is compatible with select Whirlpool, Kenmore, Maytag dryers.
Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.96573220, and Maytag MEDC215EW1.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Wide Compatibility – Fits Whirlpool, Kenmore, Maytag dryers
🔥 Restores Heating – Generates reliable, consistent heat for drying
💰 Cost-Effective OEM Repair – Genuine part ensures durability and performance
🛠️ DIY Friendly – Installs with standard tools in under 30 minutes
🛡️ Fixes Common Issues – Solves no-heat problems, long drying times, or mid-cycle shutdowns
📐 Product Specification
Part Number: WP3387749
Component Type: Dryer Heating Element
Material: High-temperature resistant metal coil with mounting housing
Mounting: Direct replacement heating element assembly
Operating Conditions: Designed for residential dryers
Compliance: Genuine OEM certified
🛠️ Installation Notes
Tools Needed: Nut driver, Phillips screwdriver, needle-nose pliers
⚠️ Safety First: Always unplug the dryer before beginning repairs to prevent electrical shock.
Steps:
Disconnect power and remove dryer rear access panel.
Locate the heating element housing inside the dryer.
Disconnect wire terminals and remove screws securing the old element.
Slide out defective element and install the new WP3387749.
Reconnect wires, secure housing, and reinstall rear panel.
Restore power and test dryer heating.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🛠️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Get your dryer heating again — Add to Cart Now for a safe, factory-approved repair!
WP3387749 Dryer Genuine OEM Heating Element
Cross Reference Information
Part Number WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418.
XPARTCO WB02X10646 Hood Line Fuse
The replacement WB02X10646 Hood Line Fuse is designed for select GE range hood models. This fuse protects the hood’s electrical system (e.g., fan or light circuits) from power surges or faults. Ideal for restoring functionality to GE appliances experiencing hood-related power issues, such as fan or light failures.
Note: Disconnect power before installation. Verify voltage and amperage compatibility with your appliance model.
Replaces part numbers: WB02X10646, 873971, AH223926, EA223926, WB02X10584, WB2X10584, WB2X10646, AP3423517, PS223926.
Compatibility (WB02X10646):
Compatible with select GE microwave and range hood models, including but not limited to:
GE: JVM series, Profile, Cafe, Monogram (specific models pending verification)
Verify your model number or contact our support team for assistance.
Key Features (WB02X10646):
✅ Brand Compatibility: Fits select GE microwave and range hood models.
🔥 Specifications: Replacement hood line fuse, specifications vary by model (typically 125V–250V, verify amperage), heat-resistant.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires basic tools (e.g., screwdriver, pliers); typically installed in 10–15 minutes.
🛡️ Reliable Fixes: Addresses hood-related issues like fan or light not working.
Installation Notes (WB02X10646):
Safety First: Disconnect the appliance from the power source before installation.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your microwave or hood running today!
Add to cart now for a budget-friendly fix!
XPARTCO DC64-00828B Dryer Door Switch
The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open.
This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers.
Common Problems This Part Fixes
Dryer not starting even though the door is closed
Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently
Error codes dC, dF, dE, or d0 displayed on models with digital displays
Dryer continuing to run with the door open (unsafe failure mode — replace immediately)
Interior dryer light not turning on when the door is opened
Door switch button visibly broken, stuck, or not making the expected click when pressed
Multimeter test shows the switch fails to change state when actuated
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including:
Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related)
Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related)
Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related)
Samsung dryers — DV5 series (DV50K7500EW and related)
Samsung dryers — DVE series (DVE60M9900W and related electric models)
Samsung dryers — DVG series (DVG45N5300V and related gas models)
Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch that detects whether the dryer door is closed — required for the dryer to start and run
Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers
Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing
Durable plastic housing with metal contacts — withstands frequent door open/close cycles
Resolves Samsung door-related error codes including dC, dF, dE, and d0
Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436
Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
DC64-00828B
Also Replaces
DC64-00828A (prior version)
Part Type
Dryer Door Switch (Door Jamb Switch)
Condition
Aftermarket Replacement
Application
Electric and Gas Dryers (Samsung platform)
Dimensions
Approximately 1.73"L x 1.73"W x 0.47"H
Color
White
Material
Plastic / Metal
Error Codes Resolved
dC, dF, dE, d0 (door-related)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
What do error codes dC, dF, dE, and d0 mean on Samsung dryers?
These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage.
My dryer is running with the door open — what should I do?
A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer.
What is the difference between DC64-00828B and DC64-00828A?
These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing.
My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch?
Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 279457 Dryer Heating Element Wire Kit
The XPARTCO 279457 is an aftermarket replacement heating element connection wire kit for Whirlpool, Kenmore, Maytag, and KitchenAid electric clothes dryers. This kit includes 2 connecting wires and 2 wire connectors that join the dryer's wiring harness to the heating element terminals. Because these connections carry the full current draw of the heating circuit, they're a common failure point — the terminals and wire insulation gradually degrade from repeated heat cycling, and a loose or corroded connection creates resistance that generates even more heat, which can melt the wire insulation or the connector itself.
This kit is the correct fix when you find burnt, melted, or brittle wiring at the heating element terminals rather than a fully failed heating element — replacing just the connection wiring is far cheaper than replacing the whole element when the element itself still tests good.
Quick Answer
The XPARTCO 279457 Heating Element Wire Kit fixes a dryer with no heat, inadequate heat, or overheating caused by burnt or melted wiring at the heating element connection — not a failed heating element itself. Includes 2 connection wires and 2 wire connectors. Classic symptom: a burning smell, or visibly melted/discolored wire insulation near the heating element terminals.
Common Problems This Part Fixes
Dryer not heating or producing inadequate heat
Dryer overheating or heat cycling erratically
Visibly melted, burnt, or discolored wires at the heating element connection
Burning smell during operation
Intermittent heating caused by a loose or corroded connection
Heating element itself tests fine but the dryer still won't heat properly
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This wire kit directly replaces the following part numbers:
279457, 279457VP, 3140, T2502, AP3134638, AWP39894, EAP334206, PD00002893, PS334206
We were not able to confirm additional cross-reference numbers beyond these at this time. If you have one, contact our support team before ordering and we will verify compatibility.
Compatibility
This wire kit is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid electric clothes dryers, including models such as:
TEDX640JQ1, WED5620HW1
Numerous additional Whirlpool-built electric dryer models using the 279457 connection kit
Note: This kit has also been referenced for use with heating element 4391960 in some sourcing. This is a connection wire kit — it does not include a heating element itself. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket heating element connection wire kit
Includes 2 connection wires and 2 wire connectors
Resolves melted/burnt-wire, no-heat, and overheating symptoms caused by a bad connection
Lower-cost fix than replacing the heating element when the element itself tests good
Fits Whirlpool, Kenmore, Maytag, and KitchenAid electric dryers
Straightforward swap — typically 15–60 minutes with basic hand tools
Product Specifications
Part Number
XP279457
OEM Part Number
279457
Part Type
Dryer Heating Element Connection Wire Kit
Condition
Aftermarket Replacement
Kit Contents
2 Connection Wires & 2 Wire Connectors
Application
Whirlpool, Kenmore, Maytag & KitchenAid Electric Dryers
Installation Notes
⚠️ Unplug Power Before Installing — High-Current Connection Unplug the dryer or switch off its circuit breaker before beginning — this connection carries the full current of the heating circuit and must never be serviced live. Remove the dryer's rear or front panel per your model's service guide to access the heating element. Inspect the existing connection wires and terminals for melting, discoloration, or brittleness — if you see any of these signs, replace both wires and connectors entirely rather than reusing any part of them. Disconnect the two old connection wires from the heating element terminals, install the two new wires in their place, and secure each wire connector firmly so both connections are tight with no exposed bare wire. A loose or poor connection is the most common root cause of this failure in the first place, so double-check the fit on both connections before closing the dryer back up.
Frequently Asked Questions
Do I need a new heating element, or just this wire kit?
If the heating element itself tests good with a multimeter but you see melted, burnt, or discolored wiring specifically at the connection point, this wire kit alone is usually the correct and much cheaper fix. If the element itself has failed (no continuity), you'll need to replace the heating element too.
Why did my heating element wires melt in the first place?
This usually happens when a connection becomes loose or corroded over time, which increases electrical resistance at that point. That resistance generates extra heat right at the connection, which can melt the wire insulation or the connector. Make sure the new connection is seated tight and secure to prevent it from happening again.
How many wires and connectors are in this kit?
This kit includes 2 connection wires and 2 wire connectors — enough to replace both terminal connections on the heating element in one kit, per the original manufacturer specification.
Is this safe to install myself?
Most DIY-capable owners can complete this repair with basic hand tools in under an hour. That said, always unplug the dryer or shut off its breaker before working on it, since this connection carries the full current of the heating circuit — never work on it while the dryer is powered.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
EXPFFSB Microwave Door Switch and Fuse Kit – Replaces FSSBA016KIT & 5303319559 – Compatible with Frigidaire & Electrolux Microwaves
Product Description
Restore proper microwave safety operation with the EXPFFSB Microwave Door Switch and Fuse Kit. This aftermarket repair kit includes the essential components needed to fix common microwave door and power issues, including one door switch and one ceramic fuse.
A faulty door switch or blown fuse can prevent the microwave from starting, cause intermittent power loss, or trigger safety shutdowns. Replacing both components together helps restore reliable microwave operation and prevents repeat failures.
This kit is engineered to match original fit and electrical performance while offering a cost-effective alternative to OEM parts.
This kit includes:
1 Microwave Door Switch
1 Microwave Fuse
Replaces Part Numbers
FSSBA016KIT, FFS-BA016/KIT, PS2422854, FFSBA016/KIT-R, FFSBA016/KIT, FFSBA016KIT, 5303319559, 634759, 75303319559, PD00026535, EAP466978, AH466978, EA466978, AP2148482, PS466978, 5304467695, 1467286, 75304467695, AH2339493, EA2339493, AP4357598, PS2339493, 5304461109, 1260958, 75304461109, AH1765534, EA1765534, AP4057424, PS1765534, 4313105, 565130, 8185302, AH358056, EA358056, AP3032745, PS358056, 5304479020, 1793730, AH3409702, EA3409702, AP4588054, PS3409702
Compatibility
This microwave door switch and fuse repair kit fits select Frigidaire, Electrolux, Gibson, Kelvinator, and Kenmore (Frigidaire-manufactured) microwaves.
Common compatible models include (but are not limited to):
Frigidaire FFMV1645TS
Frigidaire FGMV176NTF
Always verify your microwave’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Complete Repair Kit – Includes door switch and microwave fuse
⚡ Restores Microwave Power – Fixes no-start and power loss issues
🔒 Door Safety Function – Ensures proper door interlock operation
🧩 Direct-Fit Components – Designed for straightforward installation
💰 Cost-Effective Repair – Replace two common failure parts at once
📐 Product Specification
Kit Number: EXPFFSB
Includes:
(1) Microwave Door Switch
(1) Microwave Fuse
Application: Microwave door interlock and circuit protection
Fuse Type: Ceramic microwave line fuse
Quality Level: Aftermarket replacement kit (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver
⚠️ Safety First: Unplug the microwave before servicing to avoid electrical shock. Microwaves contain high-voltage components—ensure the capacitor is discharged before handling internal parts.
Basic Steps:
Disconnect microwave power.
Remove the outer cabinet or control panel to access the door switch assembly.
Replace the faulty door switch.
Locate and replace the blown fuse.
Reassemble the microwave and restore power.
Test door operation and heating function.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Replacement Parts
🔄 30-Day Return Policy
Restore microwave safety and reliable operation — Add to Cart Now for a complete repair solution!
6931EL3003 CM Dryer High Limit Thermostat
110C/240F Resettable.
Fits select LG and Kenmore dryer models.
Replaces Part Numbers: 6931EL3003C, AP4457603, PS3530484, 6931EL3003, L3003
Description: This High Limit Thermostat is a replacement part for specific LG dryer models. This safety component is designed to monitor and regulate the dryer's temperature, preventing it from exceeding safe levels. Mounted on the heating chamber or exhaust duct, the high limit thermostat shuts off the heat source or the dryer itself if it detects temperatures that are too high, helping to prevent overheating and potential fire hazards.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO EXP20AG Glass Line Fuse, Fast Blow, 20A
The XPARTCO EXP20AG is an aftermarket replacement fast-blow glass line fuse rated 20A at 250V, used as the primary overcurrent protection component in microwaves and a range of other household appliances. A line fuse sits directly in the incoming power path: as long as current draw stays within its rating, it does nothing at all, but the instant a short circuit or an overcurrent condition pushes current past 20A, the thin wire element inside the fuse melts and opens the circuit — sacrificing itself to protect the more expensive components downstream, like a transformer, magnetron, or control board. A blown fuse is why an appliance can go from working normally to completely dead with no lights, no display, and no response to any button.
This is a standard-dimension glass cartridge fuse measuring 6mm x 30mm, fast-blow (fast-acting) rated, so it opens quickly once its rating is exceeded rather than tolerating a brief surge the way a slow-blow fuse would. It is commonly used across GE, Frigidaire, Whirlpool, Kenmore, and other brands' microwaves, and also turns up in HVAC control boards and various small appliances that use this same standard fuse size and rating. A fuse itself does not wear out from age the way a mechanical part does — if one has blown, it is a symptom of an overcurrent event somewhere else in the appliance, and it's worth understanding why before simply swapping in a new one.
Quick Answer
The XPARTCO EXP20AG Glass Line Fuse fixes microwaves and other appliances that have gone completely dead — no lights, no display, no response to any button. Fast-blow, 20A, 250V, standard glass cartridge, 6mm x 30mm. Commonly used across GE, Frigidaire, Whirlpool, and Kenmore microwaves and other appliances requiring this fuse size and rating. If a new fuse blows again right away, don't just keep replacing it — that almost always means there's an underlying short circuit that needs to be diagnosed first.
Common Problems This Part Fixes
Microwave completely dead — no display, no lights, no response to any button
Appliance suddenly stopped working with no warning
Microwave won't start even though the outlet has power
HVAC control board or other appliance electronics unresponsive
Appliance tripped off after a power surge or brownout
Visible blown or darkened fuse when inspected against a light
Continuity test shows an open circuit across the old fuse
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This glass line fuse directly replaces the following OEM and cross-reference part numbers:
EXP20AG, AGC20, GMA20, 20AG, 5304509451, AP6230606, PS12071294, 5304488359, AP5648907, PS5136235, 5304464087
Because this is a standard fuse size and rating rather than a brand-specific component, the exact OEM part number your appliance's manual references will vary. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This fuse is compatible with select appliances from the following brands that use a standard 20A, 250V, fast-blow 6mm x 30mm glass cartridge fuse:
GE and Hotpoint microwaves (select models)
Frigidaire microwaves (select models)
Whirlpool and Kenmore microwaves (select models)
KitchenAid, Maytag, and Amana microwaves (select models)
Select HVAC control boards and other electronics using this fuse size and rating
Note — glass vs. ceramic body: This is the glass-body EXP20AG fuse. A visually similar ceramic-body fuse (commonly labeled EXP20A) is also widely sold at the same 20A/250V rating for many of the same appliances. Check which body material your appliance's original fuse used before ordering, and always match the amperage and voltage rating exactly — never substitute a higher-amperage fuse "to stop it from blowing," since that removes the very protection the fuse is designed to provide. Contact our support team with your model number if you're unsure which fuse your appliance needs.
Key Features
Aftermarket replacement fast-blow glass line fuse — primary overcurrent protection for the appliance's incoming power circuit
Rated 20A at 250V, standard 6mm x 30mm glass cartridge dimensions
Fast-blow (fast-acting) design opens quickly once the rated current is exceeded
Resolves "completely dead," "no display," and "no response to any button" symptoms caused by a blown line fuse
Fits standard fuse holders/clips used across a wide range of microwaves and other appliances
Replaces EXP20AG, AGC20, GMA20, 20AG, 5304509451, AP6230606, PS12071294, 5304488359, AP5648907, PS5136235, and 5304464087
Compatible with GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, and Amana appliances requiring this fuse size and rating
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
EXP20AG
OEM Part Number
Varies by brand/model — see Replaces Part Numbers
Part Type
Glass Line Fuse (Overcurrent Protection)
Condition
Aftermarket Replacement
Amperage
20A
Voltage
250V
Response Speed
Fast-blow (fast-acting)
Body Material
Glass
Fuse Size
6mm x 30mm
Application
Microwaves and select other household appliances / HVAC controls
Quantity
1 fuse
Compatible Brands
GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, Amana
Installation Notes
⚠️ Danger — Microwave High-Voltage Capacitor If you are replacing this fuse in a microwave, be aware that microwaves contain a high-voltage capacitor that can store a dangerous electrical charge even after the unit has been unplugged. Never open a microwave's cabinet without first discharging the capacitor using an insulated screwdriver shorted across its terminals, and never touch the capacitor or its terminals directly. If you are not fully comfortable with this step, have a qualified appliance technician perform the fuse replacement instead.
⚠️ Unplug The Appliance Before Starting — Match Amperage And Voltage Exactly Disconnect power at the outlet or shut off the circuit breaker before beginning. Locate the fuse holder — on most microwaves this is accessible after removing the outer cabinet, often near the incoming power cord or the control board. Remove the old fuse from its clip or holder and inspect it: a blown fast-blow fuse often shows a visibly darkened or broken filament, or a scorched glass body. Test with a multimeter set to continuity if the fuse looks intact but you suspect it's still bad — a good fuse shows continuity end to end, a blown one shows none. Install the new EXP20AG fuse in the same holder, making sure the amperage and voltage rating match your appliance's original fuse exactly. Reassemble the cabinet, restore power, and test the appliance. Tools needed: Phillips screwdriver, insulated screwdriver (for microwave capacitor discharge), multimeter (recommended), work gloves.
Frequently Asked Questions
I replaced the fuse and it blew again right away. What's going on?
A fuse doesn't fail on its own from age — it blows because something downstream drew more current than it should have. If the new fuse blows again immediately, that's a strong sign of an underlying short circuit or a failing component such as the transformer, magnetron, or a shorted capacitor. Continuing to replace the fuse without finding that root cause will just keep blowing new fuses, and in a microwave specifically, that diagnosis involves working near a high-voltage capacitor that should only be handled by someone comfortable discharging it safely, or by a qualified technician.
Can I use a higher-amperage fuse if this one keeps blowing?
No — this is one of the most important things to avoid with any fuse. The fuse's rating is chosen specifically to protect the wiring and components in the circuit it sits in. Installing a higher-amperage fuse "so it stops blowing" removes that protection and can allow a fault to overheat wiring or damage expensive components (or start a fire) instead of safely interrupting the circuit. Always replace a fuse with the same amperage and voltage rating as the original.
How do I know if the fuse is actually blown?
Visually, a blown fast-blow fuse often shows a broken or darkened filament inside the glass body, or scorching on the glass itself. If it looks fine but you still suspect it, the reliable way to check is with a multimeter set to continuity (with the appliance unplugged and the fuse removed from the circuit) — a good fuse reads continuity end to end, while a blown fuse reads open with no continuity at all.
Is EXP20AG the same as EXP20A?
They share the same 20A/250V rating, but EXP20AG refers to the glass-body version of this fuse while EXP20A commonly refers to a ceramic-body version sold for many of the same appliances. Check which body material your appliance's original fuse used, and if you're not sure, contact our support team with your model number for confirmation.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine brand-specific OEM part, but is manufactured to the same standard 20A, 250V, fast-blow glass cartridge dimensions and rating used across the OEM fuses in compatible GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, and Amana appliances.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO EXP20AG - 5 Pack Glass Line Fuse, Fast Blow, 20A
The XPARTCO (5 Pack) EXP20AG is an aftermarket replacement fast-blow glass line fuse rated 20A at 250V, used as the primary overcurrent protection component in microwaves and a range of other household appliances. A line fuse sits directly in the incoming power path: as long as current draw stays within its rating, it does nothing at all, but the instant a short circuit or an overcurrent condition pushes current past 20A, the thin wire element inside the fuse melts and opens the circuit — sacrificing itself to protect the more expensive components downstream, like a transformer, magnetron, or control board. A blown fuse is why an appliance can go from working normally to completely dead with no lights, no display, and no response to any button.
This is a standard-dimension glass cartridge fuse measuring 6mm x 30mm, fast-blow (fast-acting) rated, so it opens quickly once its rating is exceeded rather than tolerating a brief surge the way a slow-blow fuse would. It is commonly used across GE, Frigidaire, Whirlpool, Kenmore, and other brands' microwaves, and also turns up in HVAC control boards and various small appliances that use this same standard fuse size and rating. A fuse itself does not wear out from age the way a mechanical part does — if one has blown, it is a symptom of an overcurrent event somewhere else in the appliance, and it's worth understanding why before simply swapping in a new one.
Quick Answer
The XPARTCO EXP20AG Glass Line Fuse fixes microwaves and other appliances that have gone completely dead — no lights, no display, no response to any button. Fast-blow, 20A, 250V, standard glass cartridge, 6mm x 30mm. Commonly used across GE, Frigidaire, Whirlpool, and Kenmore microwaves and other appliances requiring this fuse size and rating. If a new fuse blows again right away, don't just keep replacing it — that almost always means there's an underlying short circuit that needs to be diagnosed first.
Common Problems This Part Fixes
Microwave completely dead — no display, no lights, no response to any button
Appliance suddenly stopped working with no warning
Microwave won't start even though the outlet has power
HVAC control board or other appliance electronics unresponsive
Appliance tripped off after a power surge or brownout
Visible blown or darkened fuse when inspected against a light
Continuity test shows an open circuit across the old fuse
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This glass line fuse directly replaces the following OEM and cross-reference part numbers:
EXP20AG, AGC20, GMA20, 20AG, 5304509451, AP6230606, PS12071294, 5304488359, AP5648907, PS5136235, 5304464087
Because this is a standard fuse size and rating rather than a brand-specific component, the exact OEM part number your appliance's manual references will vary. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This fuse is compatible with select appliances from the following brands that use a standard 20A, 250V, fast-blow 6mm x 30mm glass cartridge fuse:
GE and Hotpoint microwaves (select models)
Frigidaire microwaves (select models)
Whirlpool and Kenmore microwaves (select models)
KitchenAid, Maytag, and Amana microwaves (select models)
Select HVAC control boards and other electronics using this fuse size and rating
Note — glass vs. ceramic body: This is the glass-body EXP20AG fuse. A visually similar ceramic-body fuse (commonly labeled EXP20A) is also widely sold at the same 20A/250V rating for many of the same appliances. Check which body material your appliance's original fuse used before ordering, and always match the amperage and voltage rating exactly — never substitute a higher-amperage fuse "to stop it from blowing," since that removes the very protection the fuse is designed to provide. Contact our support team with your model number if you're unsure which fuse your appliance needs.
Key Features
Aftermarket replacement fast-blow glass line fuse — primary overcurrent protection for the appliance's incoming power circuit
Rated 20A at 250V, standard 6mm x 30mm glass cartridge dimensions
Fast-blow (fast-acting) design opens quickly once the rated current is exceeded
Resolves "completely dead," "no display," and "no response to any button" symptoms caused by a blown line fuse
Fits standard fuse holders/clips used across a wide range of microwaves and other appliances
Replaces EXP20AG, AGC20, GMA20, 20AG, 5304509451, AP6230606, PS12071294, 5304488359, AP5648907, PS5136235, and 5304464087
Compatible with GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, and Amana appliances requiring this fuse size and rating
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
EXP20AG-5PK
OEM Part Number
Varies by brand/model — see Replaces Part Numbers
Part Type
Glass Line Fuse (Overcurrent Protection)
Condition
Aftermarket Replacement
Amperage
20A
Voltage
250V
Response Speed
Fast-blow (fast-acting)
Body Material
Glass
Fuse Size
6mm x 30mm
Application
Microwaves and select other household appliances / HVAC controls
Quantity
1 fuse
Compatible Brands
GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, Amana
Installation Notes
⚠️ Danger — Microwave High-Voltage Capacitor If you are replacing this fuse in a microwave, be aware that microwaves contain a high-voltage capacitor that can store a dangerous electrical charge even after the unit has been unplugged. Never open a microwave's cabinet without first discharging the capacitor using an insulated screwdriver shorted across its terminals, and never touch the capacitor or its terminals directly. If you are not fully comfortable with this step, have a qualified appliance technician perform the fuse replacement instead.
⚠️ Unplug The Appliance Before Starting — Match Amperage And Voltage Exactly Disconnect power at the outlet or shut off the circuit breaker before beginning. Locate the fuse holder — on most microwaves this is accessible after removing the outer cabinet, often near the incoming power cord or the control board. Remove the old fuse from its clip or holder and inspect it: a blown fast-blow fuse often shows a visibly darkened or broken filament, or a scorched glass body. Test with a multimeter set to continuity if the fuse looks intact but you suspect it's still bad — a good fuse shows continuity end to end, a blown one shows none. Install the new EXP20AG fuse in the same holder, making sure the amperage and voltage rating match your appliance's original fuse exactly. Reassemble the cabinet, restore power, and test the appliance. Tools needed: Phillips screwdriver, insulated screwdriver (for microwave capacitor discharge), multimeter (recommended), work gloves.
Frequently Asked Questions
I replaced the fuse and it blew again right away. What's going on?
A fuse doesn't fail on its own from age — it blows because something downstream drew more current than it should have. If the new fuse blows again immediately, that's a strong sign of an underlying short circuit or a failing component such as the transformer, magnetron, or a shorted capacitor. Continuing to replace the fuse without finding that root cause will just keep blowing new fuses, and in a microwave specifically, that diagnosis involves working near a high-voltage capacitor that should only be handled by someone comfortable discharging it safely, or by a qualified technician.
Can I use a higher-amperage fuse if this one keeps blowing?
No — this is one of the most important things to avoid with any fuse. The fuse's rating is chosen specifically to protect the wiring and components in the circuit it sits in. Installing a higher-amperage fuse "so it stops blowing" removes that protection and can allow a fault to overheat wiring or damage expensive components (or start a fire) instead of safely interrupting the circuit. Always replace a fuse with the same amperage and voltage rating as the original.
How do I know if the fuse is actually blown?
Visually, a blown fast-blow fuse often shows a broken or darkened filament inside the glass body, or scorching on the glass itself. If it looks fine but you still suspect it, the reliable way to check is with a multimeter set to continuity (with the appliance unplugged and the fuse removed from the circuit) — a good fuse reads continuity end to end, while a blown fuse reads open with no continuity at all.
Is EXP20AG the same as EXP20A?
They share the same 20A/250V rating, but EXP20AG refers to the glass-body version of this fuse while EXP20A commonly refers to a ceramic-body version sold for many of the same appliances. Check which body material your appliance's original fuse used, and if you're not sure, contact our support team with your model number for confirmation.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine brand-specific OEM part, but is manufactured to the same standard 20A, 250V, fast-blow glass cartridge dimensions and rating used across the OEM fuses in compatible GE, Frigidaire, Whirlpool, Kenmore, KitchenAid, Maytag, and Amana appliances.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPFH065A Microwave 5kV 0.65A High Voltage Fuse - Compatible with LG, Samsung, Whirlpool, Sharp, Panasonic, Bosch and many other Microwaves
Product Description
Protect your microwave with the replacement XPFH065A Microwave 5kV 0.65A High Voltage Fuse. This replacement fuse safeguards the electrical system in LG, Samsung, Whirlpool, Sharp, Panasonic, Bosch, Siemens, and many other microwaves by breaking the circuit during power surges or faults (0.65A, 5.0kV). Featuring a fast-blow glass fuse (6x40mm), it resolves issues like no power, blown fuses, or intermittent failures.
Note: Includes one fuse. Disconnect power before installation. Handle glass fuse carefully. Excess cable may need to be tied back.
Replaces part numbers: XPFH065A, XPFH-065-5KV, XPFH065A, XPFH-065-5KV, F650mA L5KV, EAF36358301, AP5249671, AH3620511, EA3620511, PS3620511.
Compatibility:
Compatible with models including but not limited to:
LG, Samsung, Whirlpool, Sharp, Panasonic, Bosch, Siemens, Daewoo, Fagor, Brandt, Candy, Hitachi, De Dietrich, Proline, Scholtes, Midea, Galanz: Select models requiring 0.65A, 5.0kV fuse
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select LG, Samsung, Whirlpool, Sharp, Panasonic, Bosch, Siemens, Daewoo, Fagor, Brandt, Candy, Hitachi, De Dietrich, Proline, Scholtes, Midea, and Galanz microwaves.
🔥 Specifications: replacement high voltage fuse with holder, 0.65A, 5.0kV, fast-blow, glass fuse.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires needle-nose pliers, Phillips screwdriver, work gloves; typically installed in 15–25 minutes.
🛡️ Reliable Fixes: Addresses microwave not powering on, blown fuses, or intermittent power issues.
Product Specification
Part Number: XPFH065A
Fuse Type: Fast-blow, high voltage
Current Rating: 0.65A (650mA)
Voltage Rating: 5.0kV (5000V)
Fuse Material: Glass tube
Fuse Dimensions: 6mm diameter x 40mm length (1/4" x 1-5/8")
Compliance: UL-listed components, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the microwave from the power source before installation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Get your microwave running today!
Add to cart now for a budget-friendly fix!
XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit
The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed.
This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below.
Quick Answer
The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run.
Common Problems This Part Fixes
Dryer door won't stay closed
Door pops open in the middle of a cycle
Dryer won't start because the open-door condition isn't clearing
Worn, cracked, or damaged catch or strike
Heat escaping around the door, leaving clothes damp
Door that no longer latches with a firm, positive click
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door latch kit directly replaces the following part numbers:
5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570
This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts.
Compatibility
This latch kit is used on dryer models from the following brands:
Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers
Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers
GE and Hotpoint dryers
Select LG and Kenmore (LG-built) dryers
Select Crosley, Norge, and Speed Queen dryers
Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch.
Key Features
2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike
Replaces both halves of the latch in one repair
Restores a secure door closure so heat stays in and the dryer runs efficiently
Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start
Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering
2 kits per order (2 door catches and 2 strikes in total)
Product Specifications
Part Number
EXP570 (2 Pack)
OEM Part Number
279570, 5303207102, WE01X10023, 4027EL2001A
Part Type
Dryer Door Latch Kit (Door Catch & Strike)
Condition
Aftermarket Replacement
Kit Contents
1 Door Catch & 1 Strike per Kit
Quantity
2 Kits (2 Door Catches & 2 Strikes)
Application
Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly.
Frequently Asked Questions
My dryer door won't stay shut — is this the part I need?
Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix.
My dryer won't start and seems to think the door is open. Could this be the cause?
It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead.
What's included in the kit?
This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch.
Will this fit my Whirlpool, Frigidaire, GE, or LG dryer?
This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
