Search results for "furnace safety"

XP30A-FB Ceramic Line Fuse, Fast Blow, 30A - 6.35 x 32 mm The XP30A-FB is a replacement fast-blow ceramic line fuse rated 30A, measuring 6.35 x 32 mm (about 1/4" x 1-1/4"). A line fuse sits in the incoming power path of an appliance. It does nothing while current stays within its rating, but if a short circuit or overload pushes current past the rating, the element inside melts and opens the circuit, protecting the components behind it. A blown line fuse is a common reason an appliance goes completely dead. This is a rating-based fuse, sold by amperage, speed, body, and size rather than by appliance brand, so it fits any appliance whose fuse holder and original fuse match 30A, fast blow, ceramic, 6.35 x 32 mm. A fuse usually blows because of a problem elsewhere in the appliance, so it is worth finding the cause as part of the repair. Quick Answer The XP30A-FB Ceramic Line Fuse is a 30A, fast-blow, 6.35 x 32 mm ceramic fuse that replaces a blown fuse of the same rating and size. Match the rating and size printed on your old fuse before ordering. Classic symptom: the appliance is completely dead, with no lights, display, or response, and the old fuse tests open. Common Problems This Part Fixes Appliance completely dead, with no lights or display Appliance stopped working suddenly after a power surge or fault Old fuse tests open (no continuity) or looks blackened Keeping a rated spare on hand for repairs Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This fuse is sold under the following part number and rating: XP30A-FB, 30A Fast Blow, 6.35 x 32 mm, ABC-30, BK/ABC-30, 0ADEC9300-BE, 0314030.MX52LP, BK-AHC-30-R, BK-AHCF-V-30-R This is a rating-based fuse, so there is no single manufacturer part number. Match your appliance's fuse by the rating and size marked on the old fuse or listed in your service manual. Compatibility This fuse is for appliances that use a: 30A, fast-blow (fast-acting) ceramic fuse 6.35 x 32 mm fuse size (about 1/4" x 1-1/4") Note: The amperage, speed, body, size, and voltage rating must all match the original fuse. Never substitute a higher-amperage fuse to stop it from blowing, since that removes the protection the fuse provides. Check the markings on your old fuse or your service manual, and contact our support team with your model number if you're unsure. Key Features Replacement ceramic line fuse, 30A Fast-blow (fast-acting): opens quickly once the rating is exceeded 6.35 x 32 mm size Overcurrent protection for the appliance's incoming power circuit Sold by rating, so it suits any appliance that calls for a 30A fast-blow ceramic fuse of this size Product Specifications Part Number XP30A-FB Part Type Ceramic Line Fuse Condition Aftermarket Replacement Current Rating 30A Response Speed Fast Blow (Fast-Acting) Body Material Ceramic Fuse Size 6.35 x 32 mm Installation Notes ⚠️ Danger: Microwave High-Voltage Capacitor If this fuse is in a microwave oven, the high-voltage capacitor can hold a lethal electrical charge even after the microwave is unplugged. Do not open a microwave's cabinet unless you are trained to discharge it safely. Have a qualified technician replace the fuse if you are not. ⚠️ Unplug The Appliance Before Starting Disconnect power at the outlet or switch off the circuit breaker before beginning, and wear work gloves. Locate the fuse holder using your service manual, remove the old fuse, and check it for continuity if you are unsure whether it has blown. Fit the new fuse in the same holder, confirm the rating and size match the original, then reassemble and test. If the new fuse blows right away, stop and have the appliance checked for a short circuit or failed component. Frequently Asked Questions My appliance is dead. Is this the part I need? A blown line fuse is one possible cause. Check the old fuse for continuity with the appliance unplugged. If it is open, replace it with a fuse of the same rating and size, and find out why it blew. The new fuse blew right away. What's wrong? A fuse blows because something drew more current than it should, so repeated blowing usually points to a short circuit or a failed component. Don't keep replacing it, and don't fit a higher-rated fuse. Have the appliance diagnosed. What does fast blow mean? A fast-blow (fast-acting) fuse opens quickly once its rating is exceeded, rather than tolerating a brief surge the way a slow-blow fuse does. Replace a fast-blow fuse with another fast-blow fuse. Will this fit my appliance? It fits if your fuse holder and original fuse are 30A, fast blow, ceramic, 6.35 x 32 mm. Check the markings on your old fuse, or contact our support team with your model number and we'll help you confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4TM-C12 Refrigerator / Freezer Compressor Overload 1/2 HP Refrigerator / Freezer Thermal Overload Protector 1/2 HP (375W) - 110V 4TM-C Replaces Part Numbers: 6750C-0004R, AP4651578, PS3529535, 6750C-0005P, AH3529540, EA3529540, AP4439459, PS3529540.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10209656 Range Surface Igniter – Compatible with Whirlpool, Maytag, KitchenAid, and Kenmore Gas Ranges Product Description Restore reliable burner ignition with the XPARTCO W10209656 Range Surface Igniter. This high-quality aftermarket replacement provides the heat needed to ignite gas burners on your cooktop. A weak or failed igniter can cause burners not to light or take too long to ignite. Replacing it with this durable XPARTCO igniter restores instant ignition and safe cooking performance. Replaces Part Numbers WPW10209656, W10209656, 1468965, 98008959, 98012193, 98014514, 98014515, 98017561, 98017562, 98017917, W10112313, W10127479, AP6017135, PS11750430. Compatibility This replacement surface igniter is compatible with select Whirlpool, Maytag, KitchenAid, and Kenmore gas ranges. Example compatible models include (but are not limited to): Whirlpool WFG320M0BS3, Maytag MGR6600FZ0, and Kenmore 665.75002100. Always verify your range’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Compatible with Whirlpool-brand gas ranges 🔥 Reliable Ignition – Provides consistent spark for fast burner lighting 💰 Affordable Solution – Quality alternative to OEM parts at lower cost 🛠️ DIY Friendly – Installs easily with basic hand tools 🛡️ Fixes Common Issues – Solves burners not igniting or clicking without flame 📐 Product Specification Part Number: W10209656 Component Type: Gas Range Surface Igniter Material: High-temperature ceramic base and metal electrode Mounting: Direct-fit replacement for surface burner assembly Operating Conditions: Designed for standard household gas ranges Compliance: Built to OEM-equivalent standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the range and shut off the gas supply before starting repairs. Steps: Disconnect power and shut off gas supply. Remove burner grates and top panel to access the igniter. Detach the wire connector and mounting screw from the old igniter. Install the new XPARTCO W10209656 igniter and reconnect wires. Reassemble burner components, restore power and gas, and test ignition. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Enjoy quick, reliable ignition every time — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XP4P-ROLP-120P15 Refrigerator Starter Relay & Overload Protector Refrigerator Compressor Overload Protector PTC Starter Relay Replaces 1.03.01.01.324J, ZHB35-120P15 BEU: This PTC starter relay is specifically designed for refrigerator compressors. It serves as an overload protector and ensures the proper functioning of your refrigerator compressor. The model ZHB35-120P15 BEU guarantees compatibility with your appliance. Description: Easy to install and replace your old part: This PTC starter relay for refrigerator compressor overload protector is designed for easy installation and replacement of your old part. It saves you time and effort in the installation process. Check well before shipment: Each unit of this refrigerator compressor overload protector PTC starter relay is carefully checked before shipment to  for ensure its quality and functionality.  This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WR50X10068 Refrigerator Defrost Thermostat – Replacement for GE, Hotpoint, and Kenmore Product Overview This Defrost Thermostat is a replacement part designed for use in select GE refrigerator models. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monitoring the temperature of the evaporator coil and turning off the defrost heater when the coil gets warm enough, thus safeguarding the freezer from getting too hot.  Defrost thermostat for refrigerator or freezer L140-30F. 6" long wire, wire connectors not included. Replaces Part Numbers This thermostat replaces WR50X10068, WR50X10015, WR50X10017, WR50X10018, WR50X10028, WR50X10051, WR50X10052, WR50X10053, WR50X10054, WR50X10074, WR50X10075, WR50X10079, L140-30F, AH1017716, EA1017716, AP3884317, PS1017716.  It is designed to match OEM performance and fit in a wide range of GE and GE-built refrigerator models. Compatible Brands Compatible with refrigerators from GE, Hotpoint, and Kenmore models manufactured by GE. Suitable for top-freezer and side-by-side configurations that use a defrost thermostat with this part number. Fixes the Following Issues Frost or ice buildup in freezer Refrigerator not defrosting Poor airflow and cooling performance Defrost cycle not activating Why Buy from Express Parts Direct Cost-effective aftermarket alternative Fast and free shipping across the U.S. Trusted by appliance technicians and DIY users Easy to install and reliable in performance

Read more less

XPARTCO WB02X10646 Hood Line Fuse The replacement WB02X10646 Hood Line Fuse is designed for select GE range hood models. This fuse protects the hood’s electrical system (e.g., fan or light circuits) from power surges or faults. Ideal for restoring functionality to GE appliances experiencing hood-related power issues, such as fan or light failures. Note: Disconnect power before installation. Verify voltage and amperage compatibility with your appliance model. Replaces part numbers: WB02X10646, 873971, AH223926, EA223926, WB02X10584, WB2X10584, WB2X10646, AP3423517, PS223926. Compatibility (WB02X10646): Compatible with select GE microwave and range hood models, including but not limited to: GE: JVM series, Profile, Cafe, Monogram (specific models pending verification) Verify your model number or contact our support team for assistance. Key Features (WB02X10646): ✅ Brand Compatibility: Fits select GE microwave and range hood models. 🔥 Specifications: Replacement hood line fuse, specifications vary by model (typically 125V–250V, verify amperage), heat-resistant. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (e.g., screwdriver, pliers); typically installed in 10–15 minutes. 🛡️ Reliable Fixes: Addresses hood-related issues like fan or light not working. Installation Notes (WB02X10646): Safety First: Disconnect the appliance from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your microwave or hood running today! Add to cart now for a budget-friendly fix!

Read more less

ERP 6750CL0001D Refrigerator Compressor Overload Protector Fits Specific LG, Kenmore Refrigerator Models. This Compressor Overload is an essential replacement part designed specifically for Specific Kenmore brand refrigerators. Compatible with a wide range of LG models, this overload ensures optimal cooling performance and extends the lifespan of your refrigerator. Replaces Part Number 6750CL0001D, AH3603394, EA3603394, AP5331981, PS3603394.    This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO 242046001 Refrigerator Defrost Thermostat The XPARTCO 242046001 is an aftermarket replacement defrost termination thermostat compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore refrigerators — including French door, side-by-side, and bottom-freezer models across the CFD, DGHF, E23BC, and EI23BC series. The defrost thermostat is a bi-metal safety device clipped to the evaporator coil or defrost heater tube in the freezer compartment. During the defrost cycle, it monitors the coil temperature and opens its circuit once the coil warms to roughly 50–60°F (10–15°C), which cuts power to the defrost heater. This confirms all the ice has melted and prevents the heater from continuing to run and overheating the freezer. When the thermostat fails, one of two things happens: it can fail open (the defrost heater never runs, so ice builds up on the coils until airflow is blocked and cooling fails), or it can fail closed (the heater runs too long, overheating the compartment and often producing water pooling at the bottom of the freezer or leaking onto the floor). Features a cylindrical metallic body with two blue wires and white electrical connectors. Specification code L47-22F. Wire leads approximately 7.9". It directly replaces 242046001, 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, and L47-22F. Tip: the defrost thermostat, defrost heater, and defrost timer/control board form the defrost system and often fail together — replacing them as a set while the panel is off saves a repeat repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 242046001 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse refrigerators with excessive frost or ice buildup on the evaporator coils, fridge or freezer too warm (or too cold), the defrost cycle not activating, the refrigerator running continuously, or water pooling/leaking in the freezer. Bi-metal defrost termination thermostat — opens around 50–60°F to shut off the defrost heater. Cylindrical metal body, 2 blue wires, white connectors. Replaces 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, L47-22F. Often replaced together with the defrost heater and defrost timer. Common Problems This Part Fixes Excessive frost or ice buildup on the evaporator coils — defrost heater never running because the thermostat failed open Freezer section too warm — iced-over coils blocking airflow Refrigerator section too warm — cold air not circulating past frosted coils Freezer or fridge section too cold — erratic defrost cycling Defrost cycle not activating at all Refrigerator running continuously without cycling off Water pooling at the bottom of the freezer or leaking onto the floor — defrost heater running too long because the thermostat failed closed Reduced cooling efficiency and food spoiling faster than normal Multimeter continuity test on the thermostat shows an open circuit when cold (it should show continuity when cold) Top of the thermostat visibly popped up or bulged — a sign of failure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This defrost thermostat directly replaces the following OEM and cross-reference part numbers: 242046001, 1564839, AFR15304, AH2378768, AP4508400, EA2378768, EAP2378768, PD00005910, PS2378768, 240386402, 1258898, 240386403, AFR1311401, AH1525990, AP3970214, EA1525990, EAP1525990, PD00029401, PS1525990, L47-22F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: to replace a 240386402, you may need to remove the wire plugs from this thermostat. Also known as a defrost bi-metal thermostat, defrost bimetal thermostat, or defrost termination thermostat. Compatibility This defrost thermostat is compatible with select refrigerators from the following brands: Frigidaire refrigerators — CFD26 series (CFD26SDS0, CFD26WIS0/S1/S3/S4/S5/S6), CFD27 series (CFD27SDPS0, CFD27WIPB2/PB3, CFD27WIPS2/PS3, CFD27WIPW2/PW3) Frigidaire refrigerators — CFD28 series (CFD28SDS1/SDS6/SDS9, CFD28WIB5–WIBC, CFD28WIS0–WISC, CFD28WIW5–WIWC and related revisions) Frigidaire refrigerators — DGHF2360PF0, DGHF2360PF1 series Electrolux refrigerators — E23BC68 series (E23BC68JPS0–JPSAA, E23BC68JSS0/SS1/SS2), E23BC78 series (E23BC78IPS8–IPSJA, E23BC78ISS7) Electrolux refrigerators — EI23BC30 series (EI23BC30KB1/KB2/KB3, EI23BC30KS1/KS2/KS3, EI23BC30KW1/KW2/KW3), EI23BC35 series (EI23BC35KB3–KB8, EI23BC35KS3–KS7) Crosley refrigerators (select Frigidaire-built models) Gibson refrigerators (select models) Kelvinator refrigerators (select models) Tappan refrigerators (select models) Westinghouse and White-Westinghouse refrigerators (select models) Kenmore / Sears refrigerators (select Frigidaire/Electrolux-built models) Note: The defrost thermostat, defrost heater, and defrost timer/control board work together as a system — when one fails, the others have typically experienced the same age and stress. Since the rear freezer access panel must already be off and all three components are right next to each other, replacing them together in one session prevents a repeat repair. Always verify your appliance model number before ordering. Key Features Defrost termination thermostat (bi-metal) — monitors the evaporator coil temperature during the defrost cycle and cuts power to the defrost heater once the ice has melted Opens its circuit at approximately 50–60°F (10–15°C) — preventing the defrost heater from overheating the freezer compartment and saving energy Protects the evaporator from overheating during the defrost cycle Resolves "frost buildup," "too warm," "too cold," "defrost not activating," "runs continuously," and "water leaking in freezer" symptoms when caused by thermostat failure Cylindrical metallic body with two blue wires and white electrical connectors Sealed component — clips onto the evaporator coil or defrost heater tube Specification code L47-22F — opens at approximately 47°F Wire leads approximately 7.9" — connect inline with the defrost heater Tube-mount clip-on design — latches onto the evaporator tubing Replaces 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, and L47-22F Compatible with Frigidaire CFD26/CFD27/CFD28/DGHF series, Electrolux E23BC/EI23BC series, plus Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators Often replaced together with the defrost heater and defrost timer/control board as a paired defrost-system repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP242046001 Part Type Refrigerator Defrost Termination Thermostat (Bi-Metal) Condition Aftermarket Replacement Application Refrigerators (Frigidaire/Electrolux platform) Specification Code L47-22F Opening Temperature Approximately 47°F (L47-22F rating) Function Cuts power to the defrost heater once ice has melted Body Cylindrical metallic Wiring Two blue wires (approx. 7.9") with white electrical connectors Mounting Tube mount — clips onto evaporator coil or defrost heater tube Location Freezer compartment, behind rear evaporator panel Also Known As Defrost bi-metal thermostat, defrost termination thermostat Often Paired With Defrost Heater, Defrost Timer / Control Board Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator from the electrical outlet and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The defrost thermostat is located in the freezer compartment behind the rear evaporator access panel. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access to the back wall. If there's heavy ice buildup covering the coils, allow the freezer to thaw completely before continuing — never chip or pry ice off the evaporator coils, as the aluminum fins damage easily and a damaged coil is a far more expensive repair. Remove the screws securing the rear evaporator access panel and carefully detach it to expose the evaporator coils, defrost heater, and defrost thermostat. Locate the thermostat — it's the small cylindrical metal component clipped onto the evaporator coil or the defrost heater tube, with two blue wires. Photograph the wiring connections and mounting position before disconnecting. Carefully disconnect the electrical connectors from the old thermostat, noting their orientation. Release the mounting clip and remove the old thermostat. Clip the new 242046001 thermostat onto the coil or heater tube in the exact same position — good thermal contact with the coil is essential for the thermostat to sense the temperature correctly. Reconnect the electrical connectors. While the panel is open, inspect the defrost heater and defrost timer/control board — if either is damaged or you're chasing a defrost problem, this is the ideal time to replace them too. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions What does a defrost thermostat actually do? It's the "off switch" for your refrigerator's defrost heater. Frost naturally accumulates on the evaporator coils during normal cooling. Periodically, the defrost timer/control board turns on the defrost heater to melt that frost. The defrost thermostat — a bi-metal switch clipped right to the coil — monitors the coil's temperature during this cycle. When the coil warms to approximately 47°F (its L47-22F rating — indicating all the ice has melted), the thermostat opens its circuit and cuts power to the heater. This stops the heater before it overheats the freezer compartment, and saves energy. Without a working thermostat, the defrost cycle either never runs (ice builds up) or runs too long (overheating and water pooling). I found water pooling in my freezer — is the defrost thermostat the cause? Quite possibly. A defrost thermostat that fails closed (stuck in the "on" position) lets the defrost heater run far longer than it should. The excess heat melts more than just the frost on the coils, producing more water than the drain can handle — which pools at the bottom of the freezer and can leak onto the floor. This is a commonly misdiagnosed symptom: many people assume they have a water line leak when the actual culprit is a failed defrost thermostat. If you're seeing unexplained water in the freezer or on the floor and there's no obvious water line issue, check the defrost thermostat. Also verify the defrost drain isn't clogged, which produces similar symptoms. How do I test the defrost thermostat? With the refrigerator unplugged, disconnect the thermostat's wire connectors and set your multimeter to continuity mode. A working defrost thermostat should show continuity when it's cold (below its opening temperature — which it will be if it's been in the freezer). If it reads open (no continuity) while cold, the thermostat has failed and needs replacement. For a more thorough test, place the thermostat in ice water (should show continuity), then warm it above its ~47°F opening point (should open — no continuity). If it doesn't switch at the correct temperatures, replace it. Another visual check: if the top of the thermostat has popped up or bulged, that's a sign it has failed. Should I replace the defrost heater and timer at the same time? Yes, it's strongly recommended. The defrost thermostat, defrost heater, and defrost timer/control board work together as a system — the timer initiates the defrost cycle, the heater melts the frost, and the thermostat terminates the cycle when the coil is clear. When one component fails, the others have typically experienced the same age and thermal stress, and a near-term failure of another defrost component is common. Since the rear access panel is already off and all three components are right there next to each other, replacing them together in a single session prevents a repeat repair down the road. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the L47-22F specification (opening at approximately 47°F), bi-metal switching function, cylindrical body, two-blue-wire connector configuration, and tube-mount clip of the original 242046001 defrost termination thermostat used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR07X10097 Refrigerator Compressor Overload Relay – Compatible with GE, Hotpoint, and Kenmore Refrigerators Product Description Restore proper compressor protection and reliable cooling with the XPARTCO WR07X10097 Refrigerator Compressor Overload Relay. This Start Device Assembly is a replacement part for Specific refrigerator models. It is a kit that includes the start relay and overload, both of which are crucial components for the proper operation of the compressor. The start relay is responsible for initiating the compressor's operation by providing an electrical boost to start the motor. The overload, on the other hand, acts as a protective device. It monitors the current flow and protects the compressor from overheating or electrical overload. Replaces Part Numbers WR07X10097, 1265640, AH1766101, EA1766101, PD00008007, EAP1766101, AP4300623, PS1766101. Compatibility This replacement compressor overload relay fits select GE, Hotpoint, and Kenmore refrigerators. Example compatible models include (but are not limited to):GE GTS18HGTHWW, GTS22KGNRWWHotpoint HSS25GFTSAKenmore 363.9557710 Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM electrical protection performance 🔌 Compressor Safety Protection – Prevents overheating and electrical overload damage 🔇 Reduces Clicking Issues – Helps resolve start-up clicking or compressor cycling 💰 Cost-Effective Solution – Reliable alternative to OEM parts 🛡️ Fixes Common Issues – Solves compressor not starting, intermittent cooling, or shutdowns 📐 Product Specification Part Number: WR07X10097 Component Type: Refrigerator Compressor Overload Relay Material: Heat-resistant housing with internal thermal protection Mounting: Direct-fit on compressor terminals Function: Overcurrent and overheat protection Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Unplug the refrigerator before servicing. Compressor components may be hot—allow time to cool. Steps: Disconnect power and remove the rear lower access panel. Locate the overload relay attached to the compressor terminals. Carefully disconnect the old relay. Install the new XPARTCO WR07X10097 overload relay securely. Reinstall the access panel and restore power. Allow several minutes for compressor startup. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your refrigerator compressor and restore reliable cooling — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 3405-001034 Microwave Door Switch (Normally Open) The XPARTCO 3405-001034 is an aftermarket replacement normally open (NO) microwave door interlock switch for select Samsung, Whirlpool, Maytag, Kenmore and other microwave ovens, replacing part 3405-001034. The switch detects when the door is fully closed and completes the safety circuit, so the microwave runs only when the door is shut. When it fails, the microwave may not start, may not heat, or may only run if you push or jiggle the door. Microwaves often use more than one door switch, and each is sold individually. Check that the switch you are replacing is the normally open type and goes in the same position. ⚠️ Critical Safety Part — Switch Type And Position Must Match Exactly Door interlock switches work together as a safety system. Installing the wrong type (normally open vs. normally closed) or putting a switch in the wrong position can let the microwave run with the door open, a serious radiation hazard. Replace each switch with the exact same type in the exact same position, and test the microwave after replacement. If you are not qualified to service microwave ovens, use a trained technician. Quick Answer The XPARTCO 3405-001034 Microwave Door Switch (Normally Open) replaces a failed normally open door interlock switch on a compatible microwave. Replaces 3405-001034 and 3405-000178. Classic symptoms: the microwave won't start, won't heat, or only runs when you push or jiggle the door. Common Problems This Part Fixes Microwave won't start Microwave runs but doesn't heat Microwave only works if you push or jiggle the door Microwave doesn't shut off properly when the door opens Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following part numbers: 3405-001034, 3405-000178, AP4044834, ASM392474, EAP11741686, PD00025810, PS4131192, WP3405-001034, AP6008546, AWP47167, PD00078424, PS11741686 Samsung also uses nearby numbers, such as 3405-001033, for different switches. They are not interchangeable by number alone. If your old switch shows a different number, contact our support team and we'll check whether it matches. Compatibility This switch is listed for Samsung, Whirlpool, Maytag, Amana, Jenn-Air, Kenmore and Magic Chef microwave ovens and microwave/oven combinations, including these examples: Kenmore 40180082010, 40180099700, 40185042010 Samsung SMH1622W Note: The models above are a small sample of those listed by retailers. Confirm that your original switch is normally open and goes in the same position, check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Normally open (NO) microwave door interlock switch Aftermarket replacement for Samsung and Whirlpool 3405-001034 Completes the safety circuit only when the door is fully closed Sold individually, one switch per order Product Specifications Part Number 3405-001034 OEM Part Number 3405-001034 Part Type Microwave Door Interlock Switch Condition Aftermarket Replacement Switch Type Normally Open (NO) Application Select Microwave Ovens and Microwave/Oven Combinations Installation Notes ⚠️ Unplug Microwave And Beware Of The High Voltage Capacitor Unplug the microwave before starting and never operate it with the cabinet open. The high voltage capacitor can hold a lethal charge even after the microwave is unplugged. If your repair requires removing the outer cabinet, discharge the capacitor safely first, or have a qualified technician do the work. ⚠️ Photograph Switch Positions Before Removing Anything The switches are accessed at the door latch assembly. Before disconnecting anything, photograph each switch and its wiring, and move the wires one at a time so each goes back to the correct terminal. Make sure the actuator lines up with the latch and the switch clicks freely. After reassembly, test the microwave with a microwave-safe cup of water. Frequently Asked Questions My microwave won't heat or start. Is this the part I need? A failed door switch is a common cause, but a microwave has several switches and other parts can cause the same symptoms. Identify which switch failed and confirm it is normally open before ordering. Is this switch normally open or normally closed? This is a normally open (NO) switch. It is not interchangeable with normally closed switches, which do a different job in the interlock system. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace part 3405-001034. If you specifically need a genuine part, contact our support team. Will this fit my microwave? It is listed for many Samsung, Whirlpool, Maytag and Kenmore models, but the model list above is only a sample. Check your full model number and the type and position of your original switch, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB27X11212 Microwave Thermostat – Compatible with GE, Hotpoint & Kenmore Microwaves Product Description Ensure safe microwave operation with the XPARTCO WB27X11212 Microwave Thermostat. This high-quality aftermarket replacement monitors internal temperatures and shuts off power if overheating is detected. A faulty thermostat can cause the microwave to shut off unexpectedly, fail to heat, or stop mid-cycle. Replacing it with this reliable XPARTCO thermostat restores proper temperature regulation and protects critical internal components. Replaces Part Numbers WB27X11212, 3026293, SE-7350-006, KSD201 - 120C, WB24X28948, WB27X10854, AP5791056, PS8754627. Compatibility This replacement microwave thermostat fits select GE, Hotpoint, and Kenmore microwave ovens. Example compatible models include (but are not limited to):GE JVM1540DM5BB, JVM3160RFSSHotpoint RVM5160DHBBKenmore 363.62709300 Always verify your microwave’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM temperature-sensing performance 🌡️ Overheat Protection – Prevents damage by cutting power at unsafe temperatures 💰 Cost-Effective Repair – Reliable solution without OEM pricing 🛠️ Direct-Fit Design – Installs easily with existing mounting and wiring 🛡️ Fixes Common Issues – Solves random shut-offs, no-heat conditions, or thermal errors 📐 Product Specification Part Number: WB27X11212 Component Type: Microwave Thermostat / Thermal Switch Temperature Rating: OEM-equivalent cutoff Material: Metal housing with bimetal thermal disc Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Unplug the microwave and discharge high-voltage components before servicing. Microwave repairs involve HIGH VOLTAGE. Steps: Disconnect power and remove the microwave cover. Locate the thermostat mounted near the magnetron or cavity. Disconnect wires and remove mounting screws. Install the new XPARTCO WB27X11212 thermostat. Reconnect wiring, reinstall the cover, and restore power. Test microwave operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your microwave and restore safe operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

EXPHV10 – EXP20A Microwave High Voltage Diode and Fuse Set – Universal Microwave Repair Kit Product Description Restore proper microwave heating and electrical protection with the EXPHV10 – EXP20A Microwave High Voltage Diode and Fuse Set. This aftermarket repair kit includes a high-voltage diode and high-voltage fuse, both essential components in the microwave’s high-voltage circuit. Failed diodes or blown HV fuses can cause no-heat issues, tripped breakers, or complete microwave shutdown. Replacing both components together helps ensure reliable heating and safe operation. Diode Replaces Part Numbers HV10, EXPHV10, 2CL70, 2CL77, W10886077, WB27X7093, W10138793, DE91-70063A, 00627260, 5304468869, AP2026385, PS239843, WB27X1160, DE91-70063D, AP4236698, PS4235633, 2084375, AP2151558, PS472334, 5304417430, PS3528798, AP4439834, 6021W3B001U, 6851W1A002E, AP3960683, PS1532581, 5304456178, 3518400800, AP4433625, PS2364451, 5304472472, R9800486, AP6014695, PS11747959, WPR9800486, AP5633255, PS4085135, 11QBP0237, AP3792899, PS953886, WB27X10744, PS2370026, WB27X35382, AP4484210, WB18X10449, AP3994109, PS1481239, EA1481239, WB27X35382, PS16219547, AP6992536, WB27X10930, WB18X10449, WB27X10892, WB27X10965, WB27X11035, WB27X10562, 13091701, AP6005641 PS11738693, WP13091701, AP6005641, PS11738693, B8383102, AP3207509, PS953843, EA953843, WB27X10687, AP2026017, PS239224, WB27X10107, PS239148, AP2025948, EA239148, WB27X10037, AP6014620, PS11747873, WPDE91-70063D, PS3528798, AP4439834, 6851W1A002E, 6021W3B001R, AP5791119, PS8754690, WB27X21012, AP5791119, 3026361, PS8754690, CL04-12, Universal Microwave Diode. Fuse Replaces Part Numbers MDA-20, 0326020.HXP, 0326020.MXDP, BK1-MDP-20-R, BK-MDP-V-20-R, GSA20, 8020.0605, 8020.0605.G, WB27X10388, AP3094537, AH334641, EA334641, EAP334641, PS334641, WP4375321, W11305892, W11305905, AP6009296, PS11742452, 3601-001198, AP4046006, PS4131369, 5F1CD2031S, AP4565040, 1206681, 4922155, WB27X11151, AP4980434, PS3486702, WB27X11151, AP4980434, PS3486702, EXP20A, MDA-20, 0326020.HXP, 0326020.MXDP, BK1-MDP-20-R, BK-MDP-V-20-R, GSA20, 8020.0605, 8020.0605.G, WB27X10388, AP3094537, AH334641, EA334641, EAP334641, PS334641, WP4375321, W11305892, W11305905, AP6009296, PS11742452, 3601-001198, AP4046006, PS4131369, 5F1CD2031S, AP4565040, 1206681, 4922155, WB27X11151, AP4980434, PS3486702, WB27X11151, AP4980434, PS3486702, WB2X3910, PS242167, AP2010811, WB2X3910, WB27X995, WB27X945, B27X10388, PS239525, AP2631556, WP8183507, 8183507, PS11745084, AP6011884, M0805101, AP6014669, PS11747931, WPM0805101, 5304423383, PS472662, AP2151673, EA472662, WB27X10928, AP3994062, WB27X10388, AH1481237, EA1481237, PS1481237, W11707984, W10138793, AP7225218, PS17629444, 3B74133Q, AP4440371, PS3522743, 5F1CD0202S, 5F1CD2031S, 3B74133K. AH3522741, EA3522741, AP4438152, PS3522741.   Compatibility This universal microwave high-voltage repair set is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Kenmore, and other microwave models that use a high-voltage diode and 20A high-voltage fuse. Commonly used in countertop, over-the-range, and built-in microwaves. Always verify voltage and amperage requirements before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Matches OEM electrical and protection performance ⚡ Complete HV Circuit Repair – Includes high-voltage diode and 20A HV fuse 🔥 Restores Heating Function – Fixes microwave running but not heating 🛡️ Overcurrent Protection – Fuse protects magnetron and transformer 💰 Cost-Effective Repair – Avoid expensive magnetron or control board replacement 📐 Product Specification Part Numbers: EXPHV10, EXP20A Component Type: Microwave High Voltage Diode & Fuse Set Diode Rating: High-voltage microwave-rated diode Fuse Rating: 20A High-Voltage Fuse Application: High-voltage circuit protection and rectification Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Screwdriver, insulated pliers ⚠️ Safety First:Microwaves contain EXTREMELY HIGH VOLTAGE, even when unplugged. Always discharge the high-voltage capacitor before servicing. Professional installation is recommended. Steps: Unplug the microwave and remove the outer cover. Discharge the high-voltage capacitor safely. Locate the HV diode and HV fuse near the transformer. Replace the old components with the EXPHV10 diode and EXP20A fuse. Reassemble the microwave and restore power. Test heating operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore microwave heating and electrical safety — Add to Cart Now for a dependable, budget-friendly repair!

Read more less