Genuine OEM WH08X37938 Washer Lid Switch Assembly
The WH08X37938 is a genuine OEM lid switch (lid lock) assembly from GE for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all.
This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. As a genuine OEM part, not an aftermarket equivalent, it matches the original factory fit and specification. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour.
Quick Answer
The Genuine OEM WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, genuine OEM. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault.
Common Problems This Part Fixes
Washer won't start when the lid is closed
Washer stops partway through the wash, rinse, or spin
Lid will not lock, or stays locked after the cycle ends
Lid or door lock error codes
Loose, cracked, or visibly damaged lid lock
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This lid switch assembly replaces the following part numbers:
WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, OEM21676758, PD00087323, PS17626546
These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list.
Compatibility
This assembly is listed for select top-load washers from:
GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW
Kenmore, including 363.71542211, 363.71542310, and 363.71542410
Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers.
Key Features
Genuine OEM GE lid switch (lid lock) assembly, not an aftermarket equivalent
Replaces the lock and switch as a unit, with no need to find the failed contact
Restores starting, locking, and unlocking at the end of the cycle
Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers
Fits select GE, Hotpoint, and Kenmore top-load washers
Mounts on the cabinet with a plug-in electrical connector
Product Specifications
Part Number
WH08X37938
OEM Part Number
WH08X37938
Part Type
Washer Lid Switch (Lid Lock) Assembly
Condition
Genuine OEM
Application
Select GE, Hotpoint & Kenmore Top-Load Washers
Installation Notes
⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end.
Frequently Asked Questions
My washer won't start with the lid closed. Is this the part I need?
A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause.
Is a lid switch the same as a lid lock?
On these washers, the lid switch and lock are combined in one assembly, which this part replaces.
My old part is marked WH08X32697 or WH08X31577. Will this work?
Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm.
Will this fit my front-load washer?
No. This is for top-load washers.
Is this an OEM part?
Yes. This is a genuine OEM GE part, not an aftermarket equivalent, so it matches the original factory fit and specification.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC66-00777A Washer Pulsator Cap – Compatible with Samsung Washers
Product Description
Keep your washer operating smoothly with the XPARTCO DC66-00777A Washer Pulsator Cap. This high-quality aftermarket replacement covers the central pulsator bolt, preventing water, detergent, and debris from entering the washer hub. A cracked or missing cap can lead to corrosion, noise, or imbalance during spin cycles. Replacing it with this durable XPARTCO cap restores a secure seal and helps maintain optimal washing performance.
Replaces Part Numbers
DC66-00777A, PD00025125, EAP8753312, AP5788799, 3282678, PS8753312.
Compatibility
This replacement pulsator cap fits select Samsung top-load washers.
Example compatible models include (but are not limited to): Samsung WA400PJHDWR/AA, WA422PRHDWR/AA, and WA45H7000AW/A2.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and performance for Samsung washers
💧 Protective Seal – Keeps water and detergent away from the pulsator bolt area
💰 Cost-Effective Solution – Durable and affordable alternative to OEM caps
🛠️ Simple Installation – No tools required; snaps directly into place
🛡️ Fixes Common Issues – Replaces missing or damaged caps to prevent rust and noise
📐 Product Specification
Part Number: DC66-00777A
Component Type: Washer Pulsator (Washplate) Cap
Material: High-strength molded plastic
Color: Gray or silver finish (varies by batch)
Mounting: Snap-fit installation on top of pulsator bolt
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Always unplug the washer before performing any maintenance to avoid electrical shock.
Steps:
Open the washer lid and locate the center of the pulsator (washplate).
Remove any remaining parts of the old or damaged cap.
Align the new XPARTCO DC66-00777A cap with the pulsator hub opening.
Press firmly until it clicks into place.
Verify the cap is secure before running a wash cycle.
⏱️ Time Required: Less than 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Protect your washer from wear and debris — Add to Cart Now for a quick, reliable fix!
XPARTCO W11266654 Washer Door Boot Outer Clamp
Description: The Outer Door Boot Seal Clamp Washer is a replacement part specific to Whirlpool-brand washing machines. Multiple washers are used behind the outer boot seal clamp to create a uniform, compressed seal around the washer door opening.
Replaces Part Number: W11266654, W10237503, WPW10237503, 4894886, AP6809210, PS12584490, W10818945.
WH11X34740 Washer Genuine OEM Drain Pump Assembly – Compatible with GE & Hotpoint Washers
Product Description
Restore proper draining and reliable washer operation with the WH11X34740 Washer Drain Pump Assembly. This Genuine OEM replacement pump is responsible for removing water from the washer during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud grinding noises, or error codes. Replacing it with this Genuine OEM assembly helps ensure efficient water removal and dependable washing performance.
Replaces Part Numbers
WH23X25518, WH23X10038, WH23X25461, PD00079543, EAP16743374, AP7195487, PS16743374.
Compatibility
This Genuine OEM replacement washer drain pump assembly fits select GE and Hotpoint washers.
Example compatible models include (but are not limited to):
GE GTW465ASNWW, GTW335ASNWW
Hotpoint HTW240ASKWS
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Genuine OEM – Genuine OEM part
💧 Efficient Water Removal – Restores proper draining during cycles
🔇 Quiet Operation – Helps eliminate grinding or buzzing noises
💪 Durable Motor Construction – Designed for long service life
📐 Product Specification
Part Number: WH11X34740
Component Type: Washer Drain Pump Assembly
Voltage: 120V AC
Mounting: Direct-fit, bolt-on installation
Application: Washer drain and spin system
Quality Level: Genuine OEM
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver, pliers
⚠️ Safety First: Unplug the washer and shut off the water supply before servicing.
Basic Steps:
Disconnect washer power and water supply.
Access the drain pump from the bottom or rear of the washer.
Remove hoses and electrical connectors.
Remove mounting screws and take out the old pump.
Install the new WH11X34740 drain pump assembly.
Reconnect hoses and wiring, reassemble panels, and restore power.
Run a test cycle to confirm proper draining.
⏱️ Time Required: 25–35 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!
3360629 Washer Transmission Gearcase
Description: The Transmission is an OEM part for Whirlpool washing machines. This integral component is at the heart of the washing machine's operation, translating the motor's power into action by driving the agitator and spinning the drum. Regular inspection and maintenance can prolong the life of the transmission, but if these symptoms occur, it may be time to replace this critical component.
Replaces Part Number: 3360629, W10140307, 285362, 62621, 8546456, W10172898, WP62621, WP8546456, 285194, 285291, 285312, 285392, 285515, 3349296, 3360263, 3360629R, 3360630, 388763, 389229, 389230, 389244, 389246, 3946631, 3947637, 3949609, 423, 62528, 62531, 62534, 62570, 62668, 62680, 63025, 63167, 63320, 63563, 63910, 63999, 8532118, 99890390, 99890391, AH341974, EA341974, AP3096209, PS341974, W10140301, W10140304, W10155438, W10251783, W10251785.
XPARTCO WH13X10014 Washer Water Inlet Valve
The XPARTCO WH13X10014 is an aftermarket replacement water inlet valve for GE washer/dryer combination units — a single cabinet that houses both wash and dry functions and shares one door, lid, and control system for both. This valve sits at the point where the hot and cold water supply lines connect, and it's the gatekeeper for every drop of water that enters the tub during the wash portion of a cycle. When the control calls for a fill, the valve's solenoid opens to admit water; once the correct level is reached, it closes again.
Common causes of failure include mineral or sediment buildup inside the valve body that prevents it from sealing fully, and a burned-out internal solenoid coil. A failing valve on a combo unit produces the same core symptoms you'd see on a standalone washer: the wash side won't fill, fills too slowly, won't stop filling, or leaks after the cycle ends — but because a combo unit shares more components in a single cabinet than separate machines do, it's worth confirming the water issue is isolated to the valve and not connected to other combo-specific parts nearby, such as our WH12X955 lid switch listing, which serves this same GE combo platform. It directly replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040.
Quick Answer
The XPARTCO WH13X10014 Washer Water Inlet Valve fixes GE washer/dryer combo units that won't fill with water, fill slowly, won't stop filling, or leak after the cycle ends. For GE's combination washer/dryer platform (WSM2420/WSM2480 series). Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, 944040. This valve is specific to GE's washer/dryer combo unit — not a standalone front-load or top-load washer valve.
Common Problems This Part Fixes
Washer/dryer combo won't fill with water at the start of the wash cycle
Water fills much more slowly than normal
Unit won't stop filling — water continues past the normal level
Water leaking or dripping after the cycle has ended
Cycle stalling at the fill step and never advancing to wash
No hot water reaching the tub, or no cold water reaching the tub
Unit not washing properly due to insufficient or incorrect-temperature water
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
WH13X10014, WH13X0084, WH13X10013, WH13X84, AP3203931, 944040, AH756629, EA756629, AGE844170, PD00066092, PS756629
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select GE washer/dryer combination units, including model numbers such as:
GE WSM2420D0WW, WSM2420D1WW, WSM2420D2WW, WSM2420D3WW, WSM2420D4WW, WSM2420D5WW
GE WSM2420D0CC, WSM2420D1CC, WSM2420D2CC
GE WSM2420TAAWW, WSM2420TBAWW, WSM2420TCAWW, WSM2420TAAAA, WSM2420TAACC, WSM2420TBAAA
GE WSM2420SAZAA, WSM2420SBZAA, WSM2420SBZWW, WSM2420SCZAA, WSM2420SCZWW, WSM2420SDZWW
GE WSM2480D0WW, WSM2480D1WW, WSM2480D2WW, WSM2480D3WW
GE WSM2480SAZAA, WSM2480SAZWW, WSM2480SBZAA, WSM2480SBZWW, WSM2480SEZAA, WSM2480TCAWW
Note: This valve is built specifically for GE's washer/dryer combination units. It is not the same valve used on GE's standalone front-load washers (such as our WH13X10029 listing) and is not interchangeable with them. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement water inlet valve for GE washer/dryer combination units
Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure
Solenoid-actuated design opens and closes precisely on the control's signal
Direct drop-in replacement — matches the original mounting and hose connections
Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040
Compatible with GE washer/dryer combo units, including WSM2420 and WSM2480 series
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair using basic hand tools
Product Specifications
Part Number
WH13X10014
OEM Part Number
WH13X10014
Part Type
Washer Water Inlet Valve
Condition
Aftermarket Replacement
Application
GE Washer/Dryer Combination Units
Actuation
Solenoid-operated
Connections
Hot and cold water supply inlets
Quantity
1 valve
Compatible Brand
GE
Installation Notes
⚠️ Shut Off Water Supply And Unplug Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. On these combination units, the top of the cabinet often lifts off or opens as a single enclosure covering both the wash and dry sections, which also carries the lid switch wiring — note this connector's location before pulling the panel free. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove its mounting screws, and pull it free. Install the new WH13X10014 in the same position, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold water supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet enclosure, reconnecting the lid switch harness if it was disturbed, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the wash side fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves.
Frequently Asked Questions
Is this the same valve used on a standalone GE washer?
No. This valve is built specifically for GE's washer/dryer combination units, which share a single cabinet and control system for both wash and dry functions. GE's standalone front-load washers use a different valve (such as our WH13X10029 listing), and the two are not interchangeable. Always confirm whether your appliance is a combo unit or a standalone washer before ordering.
My unit won't stop filling. Is that this valve?
Yes, this is one of the most common symptoms of a failing valve. A worn internal seal can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it.
Only hot or only cold water isn't coming in. Do I need the whole valve?
Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold or serviced as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, connection type, and mounting configuration of the original WH13X10014 valve used in compatible GE washer/dryer combination units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH02X10363 Genuine OEM GE Washer Hub Nut
The WH02X10363 is a genuine GE OEM hub nut for GE, Hotpoint, and select RCA and Kenmore top-load washers. This nut is what secures the wash basket to the transmission's drive spline, holding the entire tub assembly firmly attached to the drive system. Every time the washer agitates or spins, this single nut is what keeps the basket properly seated and aligned rather than shifting or working loose under that repeated mechanical load.
Over years of use, or from overloading the washer with oversized loads, this nut can loosen or wear enough that the basket no longer sits securely. A failed or loose hub nut typically shows up as a basket that wobbles or feels loose, unusual noise during agitation or spin, or in more advanced cases, a basket that isn't properly engaging with the drive system at all. It directly replaces AP5793681, 3029784, and PS8757009.
Quick Answer
The WH02X10363 Genuine OEM GE Washer Hub Nut fixes GE, Hotpoint, RCA, and Kenmore top-load washers with a wobbling or loose-feeling basket, unusual noise during agitation or spin, or a basket that isn't securely engaging with the drive system. Replaces AP5793681, 3029784, PS8757009. This nut requires a very specific torque — GE's own guidance calls for a 90 ft-lb torque-limiting extension and a 1-5/16" (33mm) impact socket. Using a standard impact wrench without the torque limiter can damage both the new nut and the transmission.
Common Problems This Part Fixes
Wash basket that wobbles or feels loose
Unusual noise during agitation or spin
Basket that isn't properly engaging with the drive system
Missing or broken hub nut
Basket instability that worsens with larger or unbalanced loads
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer hub nut directly replaces the following OEM and cross-reference part numbers:
WH02X10363, 3029784, AGE1396433, AP5793681, EAP8757009, PD00046649, PS8757009.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hub nut is compatible with select GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, Café, and Kenmore washers built on the GE platform, including model numbers such as GHWN8350D0WS and GTW465ASN2WW.
Note: Always verify your full model number before ordering, since GE uses different hub nut sizes and thread designs across its washer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified thread and torque rating
Secures the wash basket to the transmission drive spline
Resolves "wobbling basket," "loose feel," and "unusual noise during agitation or spin" symptoms
1-5/16" (33mm) nut size
Direct drop-in replacement — matches the original thread and fit
Replaces AP5793681, 3029784, and PS8757009
Compatible with GE, Hotpoint, RCA, Haier, Monogram, Café, and Kenmore top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WH02X10363
Part Type
Washer Hub Nut
Condition
Genuine OEM
Brand
GE
Application
Top-Load Washers
Size
1-5/16" (33mm)
Function
Secures the wash basket to the transmission drive spline
Required Torque
90 ft-lb (torque-limiting extension required)
Thread Direction
Reverse-threaded — tightens counter-clockwise
Repair Difficulty
Moderate to Hard — specialized tools required
Quantity
1 hub nut
Compatible Brands
GE, Hotpoint, RCA, Haier, Monogram, Café, Kenmore
Installation Notes
⚠️ Critical — Correct Torque Tool Required, And This Nut Threads Counter-Clockwise Unplug the washer before beginning. Wear work gloves and safety glasses. Remove the fabric softener dispenser to access the agitator/auger assembly. Use a screwdriver to puncture through the inner shaft of the auger, then twist clockwise until the auger releases — this step can be difficult, and you'll need to hold the basket steady to keep it from rotating while you work. Lift the auger out. Remove the 11mm bolt underneath, then lift out the base assembly to expose the hub nut. Per GE's own guidance, removing and installing this nut requires a 90 ft-lb torque-limiting extension (GE part WX05X10028) along with a 1-5/16" (33mm) impact socket (GE part WX05X10022). Using a standard impact wrench without the torque limiter risks over-torquing, which can damage both the new nut and the washer's transmission. Unthread the old 33mm hub nut — this can also be difficult, so be patient and keep the basket from rotating. To install the new WH02X10363, thread it on going counter-clockwise, since this nut is reverse-threaded — the opposite direction of a standard nut. Align the base with the spline shaft, set it into position, and reassemble in reverse order: reinstall the 11mm bolt, reinstall the auger, and reattach the fabric softener dispenser. Restore power and run a test cycle to confirm the basket is stable with no wobble or unusual noise. Tools needed: impact driver or wrench with 90 ft-lb torque-limiting extension, 1-5/16" (33mm) deep well or impact socket, 3/8" to 1/2" adapter, 11mm socket, Phillips screwdriver, work gloves, safety glasses.
Frequently Asked Questions
Do I really need a special torque tool, or can I use a regular impact wrench?
GE's own manufacturer guidance is explicit on this point: a 90 ft-lb torque-limiting extension must be used when removing or installing this hub nut to prevent damage to the nut and the transmission from over-torquing. A standard impact wrench alone can apply far more force than this nut and the transmission are designed to handle, so skipping the torque limiter risks turning a simple nut replacement into a much larger and more expensive transmission repair.
Which direction does this nut turn to tighten?
This nut is reverse-threaded, meaning it tightens by turning counter-clockwise — the opposite of a standard nut. This is an easy detail to miss if you're not expecting it, and turning it the wrong direction won't seat it correctly. Keep this in mind both when removing the old nut and installing the new one.
My basket feels wobbly. Is this definitely the hub nut?
It's a strong possibility, especially if the wobble has developed gradually or worsened after washing unusually large or unbalanced loads. Since this nut is what holds the entire basket assembly firmly attached to the transmission's drive spline, a loosened or worn nut directly translates into a basket that no longer sits securely.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original thread design, size, and torque rating of the hub nut originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WPW10212596 Washer Genuine OEM Water Valve
Description: This Whirlpool valve is an OEM replacement part responsible for regulating and controlling the flow of cold water into the washing machine. This part is located at the rear of the washing machine and is connected to the cold water supply line. It opens and closes to allow the cold water to enter the washer when needed, such as during the initial filling of the machine or when rinsing clothes with cold water.
Replaces Part Numbers:WPW10212596, W10212596, 1551647, AP6017174, PS11750469, WPW10212596VP.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
5215ER2002G Washer Genuine OEM Drain Hose Assembly
Product Overview
The 5215ER2002G Washer Genuine OEM Drain Hose Assembly is designed to carry wastewater from the washer tub to the household drain. This OEM drain hose ensures proper water flow and prevents leaks, helping your washer drain efficiently and reliably. Flexible drain hose assembly that carries wastewater from your washer to the household drain. Replace if cracked, leaking, or damaged during installation.
Quick Answer
If your washer is not draining, leaking from the back, or showing drain errors, the 5215ER2002G drain hose may be clogged, cracked, or damaged. Replacing it restores proper drainage and prevents leaks.
Replaces Part Numbers
Replaces OEM part number: 5215ER2002G, AEM73773301, 5215ER2002Q, 1268108, 4932ER3008A, 5215ER2002B, 5215ER2002C, 5215ER2002D, 5215ER2002E, 5215ER2002F, 5215ER2002N, 5215ER2002R, 5215ER2002S, 5215ER2002Y, AEM75033801, AGM75511501, ALG51596, PD00005676, 095225452741, AH3527325, EA3527325, AP4457291, PS3527325.
Compatibility
This drain hose assembly is compatible with select LG and compatible front-load washers.
LG Front-Load Washers
Kenmore (LG-built) Washers
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
Common Problems This Part Fixes
Washer not draining
Water leaking from hose or rear panel
Drain errors or slow drainage
Cracked, kinked, or clogged hose
Key Features
Genuine OEM drain hose assembly
Ensures proper wastewater flow
Leak-resistant construction
Exact-fit replacement for compatible models
Product Specifications
Part Number: 5215ER2002G
Part Type: Washer Drain Hose Assembly
Brand: LG
Condition: New
OEM / Aftermarket: Genuine OEM
Application: Front-Load Washers
Troubleshooting Guide
Water won’t drain → Possible blockage or damaged hose
Leak at back of washer → Cracked or loose drain hose
Slow draining → Kinked or partially clogged hose
When Should You Replace This Hose?
Replace this hose if you notice leaks, visible damage, or if your washer is not draining properly.
Installation Notes
⚠️ Disconnect power and water supply before installation. Remove clamps, detach the old hose, and install the new hose securely to prevent leaks.
Related Parts
Washer Drain Pump
Drain Pump Filter
Water Inlet Valve
Frequently Asked Questions
Will this hose fit my washer?This hose fits select LG and compatible washers. Always verify your model number.
What does a drain hose do?It carries wastewater from the washer to the household drain.
What are signs of a bad hose?Leaks, cracks, kinks, or drainage issues indicate replacement is needed.
Is this OEM?Yes, this is a genuine OEM drain hose assembly.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Genuine OEM Parts Compatibility Support
WPW10619844 Washer Genuine OEM Lid Lock Assembly
Replaces Part Numbers: WPW10619844, W10619844, W10059230, 3436901, 8563937, WPW10619844VP, AP6023438, PS11756782.
Description: This Lid Lock Assembly is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It ensures the washer lid is securely locked during operation, preventing it from being opened mid-cycle and ensuring safe and efficient washing. Common causes of a bad lid lock assembly can include wear and tear from frequent use, electrical issues such as short circuits, and physical damage from impact or mishandling. A malfunctioning lid lock can disrupt the washing cycle, leading to incomplete washes or safety concerns.
280146 Washer Motor Rotor
Product Condition:
Genuine OEM
New / Old Stock
Replaces Part Numbers: 280146, 1175771, 8565177, AH993018, EA993018, AP3882831, PS993018.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
