Search results for "washer pulley"

XPARTCO 285753A Washer Direct Drive Motor Coupler The XPARTCO 285753A is an aftermarket replacement direct drive motor coupler (also called a motor coupling or drive coupler) compatible with a wide range of Whirlpool-family top-load washers including Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The motor coupler connects the drive motor shaft to the transmission — transferring the motor's power to the transmission to drive the agitator and spin the drum during wash and spin cycles. It is a deliberate weak point in the drivetrain: if the washer is overloaded, the coupler breaks apart first, protecting the far more expensive motor and transmission from damage. This is the updated 285753A design with metal sleeves for added strength — it replaces all previous coupler styles and versions including the original 285753, 280152, 285743, and 285140. This kit includes 2 plastic coupling halves and 1 rubber isolation dampener. Dimensions approximately 2" L x 1-1/4" W x 2" H. Fits direct-drive top-load washers only — not compatible with belt-drive machines. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 285753A Washer Motor Coupler fixes top-load washers that fill and drain normally but will not agitate or spin. The motor coupler connects the motor to the transmission — when it breaks, the motor runs but neither the agitator nor the drum moves. Kit includes 2 plastic coupling halves and 1 rubber dampener. Updated design with metal sleeves. Replaces all previous coupler versions including 285753, 280152, 285743, 285140. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, and more direct-drive top-load washers. Common Problems This Part Fixes Washer fills with water and drains but will not agitate or spin Motor runs (you can hear it) but agitator and drum do not move Washer spins slowly or incompletely — clothes still very wet after spin cycle Loud humming or buzzing from the motor area without agitation or spin Burning rubber or plastic smell during the wash or spin cycle Washer shakes excessively — broken coupler causing uneven power transfer Broken plastic or rubber pieces visible inside the bottom of the washer cabinet Replaces Part Numbers This motor coupler directly replaces the following OEM and cross-reference part numbers: 285753A, 1195967, 21003, 280152, 285140, 285743, 285753, 285753AVP, 3352470, 3363664, 3364002, 3364003, 62672, 62693, 661560, 80008, 8559748, AWP39583, PD00002353, AH1485646, EAP1485646, EA1485646, TJ285753, ER285753, AP3963893, PS1485646. The 285753A replaces all previous motor coupler styles and versions. If your parts diagram shows any of the older numbers above, the 285753A is the correct current replacement. Compatibility This motor coupler is compatible with select direct-drive top-load washers from the following brands: Whirlpool top-load washers (direct drive — no belt) Kenmore / Sears top-load washers — 70 series, 80 series, 90 series, and 110 series (Whirlpool-built) KitchenAid top-load washers Maytag top-load washers (direct drive models) Amana top-load washers Roper top-load washers Admiral top-load washers Estate top-load washers Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Important: The 285753A is for direct-drive top-load washers only — machines where the motor connects directly to the transmission without a belt. It is not compatible with front-load washers or older belt-drive top-load washers. If you can see a drive belt inside your washer cabinet, this is not the correct part. Key Features Connects the drive motor shaft to the transmission — transfers motor power to drive the agitator and spin drum Intentional sacrificial part — designed to break before the motor or transmission during overload, saving far more expensive components Updated 285753A design with metal sleeves — stronger than original all-plastic versions; replaces all previous coupler styles Kit includes 2 plastic coupling halves and 1 rubber isolation dampener — complete assembly Dimensions: approximately 2" L x 1-1/4" W x 2" H Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef direct-drive washers Replaces all previous coupler versions including 285753, 280152, 285743, and 285140 Aftermarket replacement built to OEM-equivalent quality standards Cost-effective DIY repair — typically under $15 and 30–45 minutes of work Product Specifications Part Number 285753A Part Type Washer Direct Drive Motor Coupler (Motor Coupling Kit) Condition Aftermarket Replacement Application Direct-Drive Top-Load Washers (no belt) Dimensions Approx. 2" L x 1-1/4" W x 2" H Color Black / Off-White Material Rubber / Plastic / Metal (metal sleeve inserts) Kit Includes 2 plastic coupling halves, 1 rubber isolation dampener Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Remove the washer's cabinet by releasing the top panel clips and removing the front panel screws — the motor and transmission are at the bottom of the machine. The motor coupler is a three-piece assembly between the motor shaft and the transmission input shaft. Pull the motor forward to release it from the mounting clips. The broken coupler pieces will likely fall out at this point — inspect the motor shaft and transmission shaft for any remaining plastic debris and clear it. Press the new rubber dampener onto the motor shaft coupling half first, then onto the transmission shaft coupling half, and snap the motor back into the mounting clips. Verify both coupler halves are seated securely and the rubber dampener is centered between them. Reassemble the front panel and top panel. Restore power and run a short cycle to confirm the agitator and spin function normally. Work gloves recommended — sharp sheet metal edges inside the cabinet. Tools needed: Phillips screwdriver, 1/4" nut driver, flat-head screwdriver, work gloves. Frequently Asked Questions What does the motor coupler do? The motor coupler is a three-piece assembly — two plastic coupling halves and a rubber dampener — that connects the drive motor shaft to the transmission input shaft in direct-drive washing machines. The motor spins the coupler, which transfers that rotation to the transmission, which in turn drives the agitator and drum. The rubber dampener absorbs shock and vibration between the rigid motor and transmission shafts during direction changes. The coupler is intentionally designed as the weakest link in the drivetrain — if the washer is overloaded or the transmission seizes, the coupler breaks first to protect the far more expensive motor and transmission from damage. My washer fills and drains but won't agitate or spin — is the motor coupler the cause? Yes — this is the classic symptom of a broken motor coupler. Because the pump is typically driven directly by the motor before the coupler connection, a broken coupler allows the motor to run and the pump to drain normally, but neither the agitator nor the spin drum receives any power. If you can hear the motor running but nothing moves, open the washer cabinet and inspect the coupler — you will likely find broken plastic pieces at the bottom of the cabinet near the motor and transmission. Why does the motor coupler break? The most common cause is overloading — packing too many heavy items into the washer creates enough mechanical resistance that the coupler snaps rather than allowing the motor to be damaged. Other causes include a worn or seized transmission, a worn motor, normal wear over many years of use, or a single sudden jam caused by a foreign object. If your coupler breaks a second time shortly after replacement, inspect the transmission for signs of wear or binding — a stiff or seized transmission will continue to break new couplers. What is the difference between 285753 and 285753A? The 285753A is the updated current version that superseded the original 285753. The A version incorporates metal sleeve inserts in the plastic coupling halves for improved strength and durability compared to the original all-plastic design. The 285753A replaces all previous versions — including 285753, 280152, 285743, and 285140 — and is the correct part to order regardless of which older number is listed in your washer's parts diagram. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from rubber, plastic, and metal to match the dimensions and performance of the original 285753A motor coupler. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11399437 Genuine OEM Washer Drain Pump Replaces Part Numbers: AP6974144, PS12731241 Description: This Drain Pump is a Genuine OEM part for select Maytag, Kenmore, Whirlpool washer models. It is responsible for circulating water through the washing machine during all cycles. The pump draws water from the tub and dispenses it through the water supply hoses to soak, scrub, and rinse clothes.  

Read more less

W10919003 Washer Genuine OEM Drain Pump Replaces Part Numbers: W10919003, 4461359, W10775446, AP6038235, PS11770076. Description: This Water Pump is a Genuine OEM replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Read more less

W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting. Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP. Quick Answer The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first. Common Problems This Part Fixes Washer not filling with water Washer filling very slowly Water continuing to leak into the tub after the wash cycle has completed No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2. Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the washer tub Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair Product Specifications Part Number W11210459 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Controls hot and cold water flow into the tub Repair Difficulty Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. What's the easiest way to access the control panel for this repair? Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial. Is this the same as W11210463? No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X10026 Washer Genuine OEM Drain Pump Description: The GE drain pump assembly is an OEM replacement part responsible for removing wastewater, including dirty water and detergent residue, from the washer's tub during the drain cycle. This pump assembly consists of a motor and an impeller, which removes dirty water through the drain hose and out of the appliance. This part ensures that the washing machine efficiently drains water, allowing for the completion of the laundry cycle. Replaces Part Numbers: WH23X10028, WH23X10026, WH23X10037, AP4324598, AH1766031, EA1766031, PS1766031.   California Residents only WARNING: California’s Proposition 65 

Read more less

Genuine Whirlpool WPW10250667 Washer Counterweight Spring - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, Inglis Product Description Stabilize your washer with the Genuine Whirlpool WPW10250667 Washer Counterweight Spring. This OEM suspension spring is designed for select Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, and Inglis top-load washers, supporting the tub to absorb vibrations and maintain balance during wash and spin cycles. Made of high-quality stainless steel, it ensures long-lasting performance, addressing issues like excessive shaking, banging noises, or unbalanced loads. Note: Includes one counterweight spring. Disconnect power before installation. For even wear, replace all suspension springs at the same time. Replaces part numbers: WPW10250667, W10250667, 338492, 388492, 388492D, 62738, 63207, PD00002693, EAP11751118, AP6017818, PS11751118, WPW10250667VP Compatibility: Compatible with models including but not limited to: Whirlpool: LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1 Kenmore: 11010502990, 11010502991, 11016602690, 11018202790, 11018522790, 11018532790, 11018542890, 11018542891, 11018609890, 11018702790, 11018702791 Maytag, KitchenAid, Roper, Estate, Inglis: (select top-load models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, and Inglis top-load washers. ⚖️ Specifications: OEM stainless steel counterweight spring, designed for optimal vibration absorption. 💪 Reliable Performance: Authentic Whirlpool part ensures superior durability and performance. 🛠️ Easy Installation: Requires pliers and a helper to tilt the washer; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves excessive shaking, banging noises, or unbalanced loads during operation. Product Specification Part Number: Genuine Whirlpool WPW10250667 Component Type: Washer counterweight (suspension) spring Material: Stainless steel Mounting: Hook-mounted to washer tub and frame Operating Conditions: Suitable for household top-load washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a reliable fix!

Read more less

DC97-18682D Washer Genuine Drain Hose Assembly – Compatible with Samsung Washers Product Description Maintain proper water drainage with the DC97-18682D Washer Genuine Drain Hose Assembly. This OEM replacement hose is designed to channel used water safely from your washer to the household drain system. A damaged or clogged drain hose can cause leaks, standing water, or drainage errors. Replacing it with this genuine part restores dependable washer performance and prevents messy water issues. Replaces Part Numbers DC97-18682D, DC97-18682B, DC97-18682C, DC97-18682E, PD00070138, EAP16556783, AP7018854, PS16556783. Compatibility This genuine drain hose assembly is compatible with select Samsung front-load washers. Example compatible models include (but are not limited to): Samsung WF42H5000AW, WF45K6500AW, WF56H9100AW. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Designed specifically for Samsung washers 💧 Reliable Drainage – Ensures proper water flow and prevents backup or leaks 💰 Cost-Effective Solution – Avoids costly water damage and washer breakdowns 🛠️ Easy Installation – Flexible design for quick fit with standard tools 🛡️ Fixes Common Issues – Resolves leaks, clogs, or drain-related error codes 📐 Product Specification Part Number: DC97-18682D Component Type: Washer Drain Hose Assembly Material: Heavy-duty rubber and reinforced plastic fittings Mounting: Direct fit replacement with factory connections Operating Conditions: Standard residential washer use Compliance: Genuine Samsung OEM part 🛠️ Installation Notes Tools Needed: Pliers, screwdriver (if clamps are included) ⚠️ Safety First: Always disconnect power and water supply before beginning any washer repair. Steps: Turn off water supply and unplug washer. Locate drain hose at the back of the washer. Remove hose clamps securing the old drain hose. Detach old hose from washer and household drain. Connect new DC97-18682D drain hose to washer outlet. Secure with clamps and ensure a snug fit into the drain standpipe. Restore water, reconnect power, and test for leaks. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Prevent leaks and drainage problems — Add to Cart Now for a reliable, factory-approved repair!

Read more less

Choice Manufactured Parts Choice 6602-001655 Dryer Drum Belt for Samsung Aftermarket 92-inch, 5-rib / 4-groove dryer drum drive belt for select Samsung and Kenmore dryers. Product Overview The Choice 6602-001655 dryer drum belt transfers power from the dryer motor pulley to the drum so the drum can rotate during the drying cycle. This Choice Manufactured Parts aftermarket belt is designed as a replacement for Samsung belt 6602-001655 on compatible dryers. Quick Answer 6602-001655CM is a 92-inch, 5-rib / 4-groove aftermarket dryer drum belt for select Samsung and Kenmore dryers. It replaces Samsung 6602-001655 and 6602-001314. Verify the complete dryer model number before ordering. Common Problems This Part May Fix Dryer motor runs but drum does not turn Broken or snapped drum belt Belt is frayed, glazed, cracked, or stretched Thumping or slapping noise from a damaged belt Drum turns intermittently or slips under load Replaces and Cross-References 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825, 6602-001655CM, ER6602-001655. Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not manufactured by Samsung. Compatibility Fits select Samsung and Kenmore dryers using the 6602-001655 / 5-rib belt configuration. Compatible model examples include: DV203AEW/XAA DV209AEW/XAA DV218AEW/XAA DV42H5200EP/A3 DV42H5600EW/A3 DV45H7000EW/A2 DV45K6500EV/A3 DV50K7500GW/A3 DVE45R6100C/A3 DVE45R6300W/A3 DVG45T6000W/A3 Kenmore 592 Series Important: This is a partial compatibility list. Match the complete dryer model number and original belt number before purchasing. Key Features Choice Manufactured Parts aftermarket replacement 92-inch drum drive belt 5 ribs / 4 grooves Approx. 5/16-inch belt width Ribbed drive surface with smooth outer/back surface For select Samsung and Kenmore dryers Specifications Choice Part Number 6602-001655CM Brand Choice Manufactured Parts Part Type Dryer Drum Drive Belt Condition New Part Quality Aftermarket Replacement Length Approx. 92 in. Width Approx. 5/16 in. Ribs / Grooves 5 Ribs / 4 Grooves Primary Replacement For Samsung 6602-001655 Application Dryer Drum Drive System Installation Notes Disconnect dryer power before service. Access the drum and note the original belt routing before removal. Route the replacement belt around the drum, idler pulley, and motor pulley exactly as the original. Install the ribbed side toward the drum/pulley contact surface as required by the dryer design. Confirm the idler pulley applies proper tension and spins freely. Rotate the drum by hand before reassembly to verify smooth belt tracking. Diagnostic tip: Before installing a new belt, inspect the idler pulley, drum support rollers, motor pulley, and felt seals. A seized or damaged support component can quickly damage a replacement belt. FAQ Is this a Genuine Samsung OEM belt? No. This is a Choice Manufactured Parts aftermarket replacement for Samsung 6602-001655. How long is the belt? Choice specifies this belt at approximately 92 inches long. How many ribs does it have? It has 5 ribs and 4 grooves. Does it replace 6602-001314? Yes. 6602-001314 is a commonly listed earlier/cross-reference number for the 6602-001655 belt family. Does this include the idler pulley? No. This listing is for the drum belt only unless the product package explicitly states otherwise. Shop With Confidence Match your complete dryer model number and original belt number before ordering. Compatibility assistance is available if you are unsure which belt your dryer uses. Choice Replacement92-Inch Belt5 Rib / 4 GrooveCompatibility Support

Read more less

XPARTCO WE25X205 Dryer Drum Bearing The XPARTCO WE25X205 is an aftermarket replacement rear drum bearing kit for GE, Hotpoint, and Kenmore electric and gas dryers. The rear drum bearing supports the back of the drum and lets it turn smoothly and quietly as the belt drives it. When the bearing wears out, the drum starts to squeal, rumble, or grind while it turns, and a badly worn bearing can let the drum sit unevenly or scrape. This is a direct-fit aftermarket replacement for the original GE kit. GE's catalog lists WE25X205 as superseded to WE25M40, and this listing covers both numbers. Because the drum has to come out to reach the bearing, it is a good time to inspect the drum belt, idler pulley, and drum glides and replace any that look worn. Quick Answer The XPARTCO WE25X205 Dryer Drum Bearing fixes a GE, Hotpoint, or Kenmore dryer that squeals, rumbles, or grinds when the drum turns. It replaces the rear drum bearing and is also listed under WE25M40. Classic symptom: a loud squeal or rumble that follows the drum and is there with or without heat. Common Problems This Part Fixes Loud squealing or squeaking while the drum turns Rumbling or grinding noise from the back of the dryer Drum that wobbles, drags, or doesn't turn smoothly Excess vibration during a cycle Noise that continues even when the dryer is running without heat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum bearing kit directly replaces the following part numbers: WE25M40, WE25X205, 784658, WE01X0462, WE01X0463, WE02X0195, WE03M0015, WE03M0065, WE03X0022, WE03X0028, WE03X0031, WE03X0035, WE03X0036, WE03X0039, WE03X0065, WE11X0056, WE11X56, WE1X462, WE1X463, WE25M0040, WE25M40-25PK, WE25X0062, WE25X0205, WE25X205E, WE25X205R, WE25X62, WE25X62R, WE2X195, WE2X195D, WE3M15, WE3M65, WE3X22, WE3X28, WE3X31, WE3X35, WE3X36, WE3X39, WE3X65, AGE25888, AH267529, AP2619300, DE725, EA267529, EAP267529, PD00001078, PS267529, AFP1161113 These numbers span several generations of GE's own part numbering for this bearing kit. Older numbers beyond WE25X205 and WE25M40 are drawn from a retailer cross-reference, so confirm against your dryer's parts diagram or contact our support team if your model calls out a different number. Compatibility This bearing kit is listed for GE, Hotpoint, and Kenmore dryer models, including these examples: GE DDG9680RCM, DDG8580RCM, DDP1380GFM, DDE058DGAL, DDE8200GBL GE DHSR333GV0WB, DWXQ473T0WW, DPXR475EW0AA, DPXR475EW0WW, DPSR475EW0AA Note: The models above are a sample, not a full list. Retailers also reference this kit for some Fisher & Paykel dryers, which we could not confirm by model. Enter your model number at checkout or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket rear drum bearing kit for GE-built dryers Restores smooth, quiet drum rotation Covers both WE25X205 and its superseding number, WE25M40 Fixes squealing, rumbling, and grinding drum noise Fits GE, Hotpoint, and Kenmore dryers Product Specifications Part Number WE25X205 OEM Part Number WE25X205, WE25M40 Part Type Dryer Rear Drum Bearing Kit Condition Aftermarket Replacement Location Rear of Drum Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the top and front panel as shown in your model's service guide, then lift the drum belt off and slide the drum out, which is easier with a second person. Remove the old rear bearing from the back panel, install the new one in the same position, and reassemble in reverse order. Check the belt, idler pulley, and drum glides while the drum is out and replace any that are worn. Plan on about 30 minutes to 1 hour. Frequently Asked Questions My dryer squeals when the drum turns. Is this the part I need? A squeal that follows the drum is most often a worn rear drum bearing, though a worn idler pulley or drum glides can make similar noise. If you can spin the drum by hand and feel roughness or hear grinding, the bearing is a likely cause. What's the difference between WE25X205 and WE25M40? GE's catalog lists WE25X205 as superseded to WE25M40, and retailers list them as interchangeable. This listing covers both numbers. Should I replace the drum belt at the same time? It's a good idea. The drum has to come out to reach the bearing, so this is the easiest time to inspect the belt, idler pulley, and drum glides and replace anything worn. Will this fit my dryer? It is listed for many GE, Hotpoint, and Kenmore dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 661570 Dryer Drum Belt Replaces 661570V The XPARTCO 661570 is an aftermarket replacement dryer drum belt compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. The drum belt wraps around the outside of the dryer drum, loops around the idler pulley and motor pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber, this 4-rib belt measures 93-1/2 inches long x 1/4 inch wide x 1/8 inch high with 4 ribs and 3 grooves. It is a direct drop-in replacement for OEM part numbers 661570V and 661570, and is part of the 4392067 dryer repair kit. It pairs with the W10837240 idler pulley and WPW10314173 drum rollers for a complete drum drive overhaul. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 661570 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is present during operation. Compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. Measures 93-1/2" L x 1/4" W x 1/8" H with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 661570V, 661570, 3387610, 3389728, 3393999, 339728, 4248258, 661570VP, AWP761693, OEM17951196, PD00023608, FIX382430, AP5983729, PS11722115. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Amana dryers KitchenAid dryers Crosley dryers Admiral dryers Speed Queen dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the idler pulley and motor pulley for smooth, consistent tumbling every cycle 93-1/2" length x 1/4" width x 1/8" height — 4-rib, 3-groove design for a secure, slip-free grip on the pulleys Made from high-strength rubber — resists cracking, stretching, heat damage, and oil Direct replacement for OEM part numbers 661570V and 661570 — no modification required Part of the 4392067 dryer repair kit — pairs with W10837240 idler pulley and WPW10314173 drum rollers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 661570 OEM Part Number 661570V Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 93-1/2 inches Width 1/4 inch Height 1/8 inch Ribs 4 ribs, 3 grooves Material High-strength rubber Color Black Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, Speed Queen Part of Kit 4392067 Dryer Repair Kit Often Replaced With W10837240 Idler Pulley, WPW10314173 Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release the belt from the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 661570 belt around the drum with the ribbed side facing inward toward the drum. Route the belt around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (W10837240) and drum rollers (WPW10314173) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What is the difference between 661570 and 661570V? These are the same belt. 661570V is the updated OEM part number (the "V" denotes the current version) that superseded the original 661570. Both numbers refer to the identical drum belt — this aftermarket replacement is compatible with both. How does the 661570 differ from the 341241 and W10205415 belts? All three are Whirlpool-family dryer drum belts, but they differ in length, width, and rib count. The 661570 is 93-1/2" long x 1/4" wide with 4 ribs and 3 grooves. The 341241 is 92-1/4" long x 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 92" long x 3/8" wide with 5 ribs and 4 grooves. They are not interchangeable — always use the part number specific to your dryer model. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound, a burning rubber smell, or damp clothes after a full drying cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched out of shape. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (W10837240) and drum support rollers (WPW10314173) at the same time. All three parts wear together and are sold together in the 4392067 dryer repair kit. Replacing all three prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 661570V belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WPW10352973 Washer Genuine Dispenser Actuator Dispenser Drawer Switch Actuator for Washer Replaces Part Numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. ✅ Product Description: Restore proper detergent dispensing with this genuine OEM WPW10352973 washer dispenser actuator. Designed to control the flow of detergent and fabric softener into your wash cycle, this part is a direct replacement for worn or non-functioning actuators in many Whirlpool, Maytag, Amana, Kenmore, and Crosley top-load washing machines. Part Features: Genuine OEM quality – built to factory specs Replaces part numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. Controls dispenser drawer movement for proper release timing Easy to install with basic tools Fixes the following symptoms: Dispenser drawer not opening Detergent or softener not dispensing Error codes related to actuator failure Inconsistent or incomplete wash cycles Compatible with:Many models from Whirlpool, Maytag, Kenmore, Amana, and more.(Check model number before ordering or contact us for fitment help.) ✅ Why Buy from Parts-O-Matic? Guaranteed OEM-quality parts Always Fast and Free U.S. shipping Competitive pricing Expert support for part compatibility 🛒 Get your washer working like new – order the WPW10352973 Dispenser Actuator now at Parts-O-Matic.com, and enjoy fast, free shipping with no minimum.

Read more less

XPARTCO W10276397 Washer Drain Pump Replaces WPW10276397 The XPARTCO W10276397 is an aftermarket replacement washer drain pump and motor assembly compatible with a wide range of Whirlpool-family top-load washers including Whirlpool Cabrio, Maytag Centennial, Amana, Kenmore, Roper, Crosley, and Inglis. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, display error code F9E1, stop mid-cycle, or produce unusual humming or grinding noises during the drain phase. This complete drain pump and motor assembly uses a Hanyu B40-3A motor (also marked 91PS3132) and includes the integrated impeller — the impeller is not sold separately. It directly replaces WPW10276397, W10276397, WPW10276397VP, 1874334, B40-3A, LP397, AP6018417, PS11751719, and several additional cross-reference numbers. Before ordering, confirm that the drain hose and any coin trap or filter are clear — a blocked hose or clogged filter can mimic pump failure symptoms. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10276397 Washer Drain Pump fixes Whirlpool Cabrio and Maytag Centennial top-load washers that won't drain, leave standing water, display error code F9E1, or make humming/grinding noises during the drain cycle. Complete pump and motor assembly with integrated impeller. Motor: Hanyu B40-3A / 91PS3132. Replaces WPW10276397, 1874334, B40-3A, LP397, AP6018417, PS11751719. Compatible with Whirlpool Cabrio, Maytag Centennial/MVWC/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F9E1 displayed — drain pump fault or slow drain detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor running but impeller not pumping Grinding or rattling noise during drain — physical damage to impeller or pump housing Water draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WPW10276397, W10276397, 1874334, AP6018417, AWP50231 EAP11751719 FIX11751719, OEM24073670, PD00003595, PS11751719, WPW10276397VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW4800, WTW4810, WTW4850, WTW4900, WTW5000, WTW5200, WTW5300, WTW5500, WTW5600, WTW5640, WTW5700 and related models) Maytag top-load washers — Centennial series (MVWC200, MVWC215, MVWC300, MVWC400, MVWC415, MVWC416, MVWC425, MVWC465 and related models) Maytag top-load washers — MVWX series (MVWX500, MVWX550, MVWX600, MVWX700 and related models) Amana top-load washers (ATW, NTW series and related models) Kenmore / Sears top-load washers — 110 series (Whirlpool-built Cabrio-platform models) Roper top-load washers (RTW series) Crosley top-load washers (CAE series) Inglis top-load washers (select models) Note: This pump is for top-load washers only. Always verify your exact model number before ordering. Check and clear the drain hose and any coin trap before replacing the pump — a blocked hose can produce the same symptoms as a failed pump. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Complete pump and motor assembly — includes integrated impeller (impeller not sold separately) Motor: Hanyu B40-3A / 91PS3132 — matched to original pump specifications Resolves error code F9E1 (drain pump fault / slow drain) on compatible Whirlpool and Maytag top-load washers Replaces WPW10276397, W10276397, 1874334, B40-3A, LP397, and AP6018417 Compatible with Whirlpool Cabrio, Maytag Centennial/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10276397 OEM Part Number WPW10276397 Part Type Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Top-Load Washers (Cabrio, Centennial, and related platforms) Motor Hanyu B40-3A / 91PS3132 Includes Pump motor and integrated impeller assembly Error Code Resolved F9E1 (drain pump fault / slow drain) Compatible Brands Whirlpool, Maytag, Amana, Kenmore, Roper, Crosley, Inglis Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels and a shallow pan near the pump access area to catch residual water. The drain pump is located beneath the washer tub on Cabrio and Centennial models — access it by removing the front lower panel or by tilting the washer back and working from underneath. Disconnect the drain hose clamp and hose from the pump, then disconnect the wire harness connector. Unscrew the pump mounting screws and remove the old pump. Before installing the new pump, verify the drain hose and any coin trap or filter are completely clear of debris — a blocked hose or trap will cause the new pump to fail again. Install the new W10276397 pump in the same position, reconnect the hose and wire harness, and secure the mounting screws. Restore power and water and run a drain or spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What does error code F9E1 mean on Whirlpool Cabrio and Maytag Centennial washers? F9E1 indicates a drain fault — the washer was unable to drain within the expected time during the cycle. It can be caused by a clogged drain hose, a blocked coin trap or filter, a kinked drain hose, or a failed drain pump motor. Always check and clear the drain hose and filter before replacing the pump — a blockage is often the cause and clearing it resolves the error without needing a new pump. If the hose and filter are clear and the error persists, the pump motor has likely failed. What is the difference between W10276397 and WPW10276397? These are the same drain pump assembly. WPW10276397 is the updated Whirlpool OEM part number that superseded the original W10276397. The 1874334 and B40-3A are also cross-references for this same pump. This aftermarket replacement is compatible with all of these numbers. My washer hums but won't drain — is it the pump? A humming sound during the drain cycle without water being expelled usually means the pump motor is receiving power and running, but the impeller is not turning — either because it is jammed with debris or because the impeller shaft has broken. First check for and remove any foreign objects (coins, lint, small clothing items) from the pump area. If the impeller is clear and the pump still hums without draining, the motor or impeller is mechanically failed and the pump assembly needs replacement. Does this pump fit the Whirlpool Cabrio and Maytag Bravos washers? The W10276397 is compatible with Whirlpool Cabrio and Maytag Centennial top-load washers on the VM transmission platform. Maytag Bravos XL and Bravos X models may also be compatible depending on the specific model number — verify your exact model before ordering. Contact our support team if you need confirmation for a specific Bravos model. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a Hanyu B40-3A motor to match the specifications and performance of the original WPW10276397 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less