Search results for "washer switch"

AJU75152606 Genuine OEM LG Washer Water Inlet Valve Assembly The AJU75152606 is a genuine LG OEM water inlet valve assembly for LG top-load agitator washing machines. This assembly connects to the washer's hot and cold water supply and controls the flow of water into the tub during the fill portion of the wash and rinse cycles — electrical signals from the control system open and close the appropriate water passage, filling the tub to the correct level and shutting off once it's reached. This electric-powered valve assembly is finished in gray, designed for freestanding installation, and rated for an 8 lb capacity washer. Common causes of failure include mineral buildup or debris restricting flow through the valve, or general electrical wear in the solenoid coils. Symptoms of a failing valve include the washer not filling with water, hose leaks at the connections, the valve not opening fully, or reduced flow rate from internal buildup. Replacing this assembly requires removing the control panel and main top of the washer — a moderate difficulty repair. It directly replaces AP7005965. Quick Answer The AJU75152606 Genuine OEM LG Washer Water Inlet Valve Assembly fixes LG top-load agitator washers that won't fill with water, are leaking at the hose connections, or have reduced flow from internal buildup. Gray, electric-powered, 8 lb capacity rating. Replaces AP7005965. Not the same as the similarly-numbered AJU75152602 valve, which is used on different LG WT7000-series models — confirm your exact part number before ordering. Common Problems This Part Fixes Washer not filling with water Hose leaks at the valve connections Valve not opening fully, restricting water flow Reduced flow rate from mineral buildup or debris Overflow or filling problems from inconsistent water pressure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AJU75152606, ALG53799, AP7005965, EAP16547657, PD00074631, PS16547657 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve assembly is compatible with select LG top-load agitator washing machines, including model numbers such as WT7000CW, WT7005CW, WT6100CW, WT6105CM, WT6105CW, T14A4SEHTW, T1490SEHTW, T15A4SEHT2, T1590SEHTW, T15A4SEHTW, T14A4SEHTC, T1490SEHTC, and T14A4SEHBW. Note — not the same as AJU75152602: A similarly-numbered valve, AJU75152602, is a separate part used on other LG WT7000-series models (WT7100CW, WT7150CW, WT7300CV, WT7300CW, WT7400CW, WT7400CV, WT7405CV, WT7405CW, WT7800CW, WT7800CV, WT7900HBA, WT7155CW). The two numbers are easy to confuse given how close they are — always confirm the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine LG OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the tub during fill Resolves "won't fill," "hose leaks," "valve not opening fully," and "reduced flow" symptoms caused by valve failure Electric-powered, gray finish Designed for freestanding installation Rated for 8 lb capacity washers Direct drop-in replacement — matches the original mounting and hose connections Replaces AP7005965 Compatible with LG top-load agitator washing machines Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AJU75152606 Part Type Washer Water Inlet Valve Assembly Condition Genuine OEM Brand LG Application Top-Load Agitator Washing Machines Color Gray Power Type Electric Installation Type Freestanding Capacity Rating 8 lb Repair Difficulty Moderate — requires control panel and main top removal Quantity 1 valve assembly Compatible Brand LG Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the washer's control panel and main top to access the inlet valve — this is a moderate difficulty repair due to the disassembly involved. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water hoses and wiring connectors from the old valve. Unscrew and remove the old inlet valve assembly. Position the new AJU75152606 in the same location and secure it with screws. Reconnect the water hoses and wiring connectors fully. Reassemble the main top and control panel. Restore the water supply and power, then run a test cycle to confirm the washer fills correctly with no leaking at the hose connections. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure, mineral buildup, or debris can prevent water from entering properly, stopping the wash cycle from proceeding. Is this the same as AJU75152602? No, these are two separate LG valve part numbers used on different washer model series, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this a difficult repair? It's a moderate difficulty repair, since it requires removing the washer's control panel and main top to access the valve. Basic hand tools are sufficient, but budget more time than you would for a simpler part swap. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH12X10527 Washer Genuine OEM Timer Replaces Part Numbers: WH12X10527, AP5645215, PS4704240. Description: This washer timer is a Genuine OEM part for select GE washing machine models. This timer controls the various cycles of the washing machine, including wash, rinse, and spin cycles. By regulating the duration and sequence of each cycle, the timer ensures that the washing machine operates smoothly and efficiently.

Read more less

W11458345 Genuine OEM Washer Drain Pump - Compatible with Whirlpool, Maytag, Amana Product Description Restore your washer’s performance with the W11458345 Genuine OEM Washer Drain Pump. This Whirlpool-manufactured pump is designed as a replacement for select Whirlpool, Maytag, Amana, Inglis, and Kenmore washing machines. It efficiently drains wastewater during wash cycles and includes a large filter that can be cleaned monthly with Washing Machine Cleaner Tablets. This part addresses issues like water not draining, loud buzzing or grinding noises, or failure to enter agitation cycles, often caused by blockages, wear, or pump motor failure. Note: Includes (1) drain pump assembly. Disconnect power before installation. Verify compatibility with your washer model. Replaces part numbers: W11458345, W11316609, W10918608, W11319789, PD00062450, EAP16218041, AP6989186, PS16218041. Compatibility: Compatible with select washer models, including but not limited to: Whirlpool: WFW862CHC3, WFW6620HW1, WFW6620HW2, WFW9620HC2, 8TWFW8620HW1 Maytag: MHW5630HW1, MHW5630HW3, 7MWFW5622HW2 Amana: NFW5800HW0 Kenmore: 110.42932200 Inglis: IFW5900HW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Amana, Inglis, and Kenmore washers. 🔧 Specifications: Genuine OEM Whirlpool drain pump, 120V, stainless steel construction. 💪 Reliable Performance: Efficiently drains wastewater for optimal washer operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–60 minutes. 🛡️ Effective Fixes: Resolves water not draining, buzzing/grinding noises, or agitation cycle issues. Product Specification Part Number: W11458345 Component Type: Washer drain pump assembly Material: Stainless steel and plastic (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Dimensions: Approximately 9.75" L x 9.5" W x 5.25" H (Based on web:0) Weight: 3.32 lbs (Based on web:0) Electrical Specs: 120V, submersible design (Based on web:0, web:2) Compliance: UL-listed, Prop 65 warning for California (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO W11165546 Washer Water Inlet Valve The XPARTCO W11165546 is an aftermarket replacement washer water inlet valve assembly compatible with Maytag Bravos XL, Whirlpool Cabrio, Kenmore 700-series, and related Whirlpool-platform HE top-load washers. This 4-solenoid assembly controls the flow of hot and cold water from the household supply lines into the washer tub and dispenser compartments. It includes an integrated thermistor on the center outlet that monitors incoming water temperature and communicates it to the control board so the washer can achieve the correct wash temperature. When the valve fails — or when a single solenoid coil burns out — the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. Rated 120V, 60Hz, with 2 inlet ports and 3 outlet ports, this assembly measures 5-3/8"L x 4-1/4"W x 3"H. The valve body may be blue or green in color depending on production run — both are functionally identical. It is compatible with 1/2" ID supply hoses. It directly replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, WV5546, 33090105, 4545980, AP6284346, EAP12348013, PD00037668, and PS12348013. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO W11165546 Washer Water Inlet Valve fixes Maytag Bravos XL and Whirlpool Cabrio/WTW HE top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. 4-solenoid valve with thermistor. 120V/60Hz. 2 inlet / 3 outlet ports. 5-3/8"L x 4-1/4"W x 3"H. Compatible with 1/2" ID supply hoses. Replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, 33090105, 4545980, AP6284346, PS12348013. Common Problems This Part Fixes Washer not filling with water — error code F8E1, LF, or LO FL displayed Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection — thermistor failed Water dripping into the tub between cycles — valve not closing completely Water leaking from the back of the washer near the valve Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: W10839828, 33090105, 4545980, W10599423, W10758828, W11096267, W11165546VP, AP6284346, AWP43457, EAP12348013, PD00037668, PS12348013. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select HE top-load washers from the following brands and series: Maytag top-load washers — Bravos XL series (MVWB765FW0, MVWB765FW1, MVWB765FW2, MVWB765FW3, MVWB765FC1, MVWB765FC2, MVWB766FW0, MVWB766FW1, MVWB835DW1, MVWB835DW2, MVWB835DW3, MVWB835DW4, MVWB855DC2, MVWB855DC3, MVWB865GC0, MVWB865GW0, MVW6230HW2, MVW7230HW0, MVW7232HW0 and related models) Whirlpool top-load washers — Cabrio / WTW series (WTW7500GC0, WTW7500GW0, WTW8500DC2, WTW8500DC4, WTW8500DC5, WTW8500DR4, WTW8500DR5, WTW8500DW4, WTW8500DW5, WTW8700EC1, 7MWTW8500EC2 and related models) Kenmore / Sears top-load washers — 700 series (11028132410, 11028132411, 11028132412, 11028132413, 11028133410, 11028133411, 11029132411, 11029133410 and related models) Crosley top-load washers (select models) Note: The valve body color may be blue or green depending on production run — both are functionally identical. This valve is for HE top-load washers only. Always verify your model number before ordering. Key Features 4-solenoid valve assembly — controls hot water, cold water, and additional dispenser/recirculation ports to fill the tub with the correct temperature water for each cycle Integrated thermistor on center outlet — monitors incoming water temperature and communicates with the control board to achieve the correct wash temperature Resolves F8E1, LF, and LO FL error codes on compatible Maytag and Whirlpool HE top-load washers Rated 120V, 60Hz — correct electrical specifications for compatible models Dimensions: 5-3/8"L x 4-1/4"W x 3"H 2 inlet ports, 3 outlet ports — compatible with 1/2" ID supply hoses Valve body color (blue or green) varies by production run — functionally identical Replaces W10599423, W10758828, W10839828, W11096267, and W11165546VP Compatible with Maytag Bravos XL MVWB series, Whirlpool WTW7xxx/WTW8xxx, Kenmore 700 series, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number W11165546 Part Type Washer Water Inlet Valve Assembly (4-Solenoid with Thermistor) Condition Aftermarket Replacement Application HE Top-Load Washers — Bravos XL, Cabrio, WTW series Solenoids 4-coil (hot, cold, and additional ports) Thermistor Integrated on center outlet — monitors water temperature Voltage 120V AC Frequency 60 Hz Dimensions 5-3/8"L x 4-1/4"W x 3"H Inlet Ports 2 (hot and cold) Outlet Ports 3 Supply Hose ID 1/2 inch Color White / Blue or Green (production run dependent — functionally identical) Error Codes Resolved F8E1, LF, LO FL Compatible Brands Maytag, Whirlpool, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose routing before disconnecting. Disconnect the two external supply hoses from the valve inlet ports using pliers to loosen any stuck connections. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from all solenoid coils and the thermistor. Unscrew the mounting hardware and remove the old valve. Install the new W11165546 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the same positions as documented. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers, channel-lock pliers for stubborn hose connections. Frequently Asked Questions What do error codes F8E1, LF, and LO FL mean on Maytag and Whirlpool washers? F8E1 (also displayed as LF or LO FL on some models) indicates a long fill fault — the washer was unable to fill to the required water level within the expected time. The most common causes are a failed water inlet valve (solenoid coil burned out or valve seat clogged), low household water pressure, or kinked supply hoses. Before replacing the valve, confirm both supply valves are fully open, the supply hoses are not kinked, and household water pressure is adequate. If all supply conditions are good and the error persists, the water inlet valve is the most likely cause. What is the difference between W11165546 and W11096267? These are the same water inlet valve assembly. W11096267 was an earlier version, and W11165546 is the current updated part number. The W10599423 and W10758828 are also cross-references to earlier versions of this same valve. The W11165546VP is the Whirlpool factory-packaged version. All of these are covered by this aftermarket replacement. Why does this valve have 4 solenoids? Modern HE top-load washers like the Maytag Bravos XL and Whirlpool Cabrio use multiple water paths for different wash functions — hot water inlet, cold water inlet, a bleach dispenser port, and a fabric softener/recirculation port. Each path is controlled by its own independent solenoid coil on the same valve assembly. This allows the control board to independently open any combination of ports needed for a given cycle phase. When any single solenoid coil fails, only the function controlled by that coil is affected — which is why the washer might fill normally with cold water but not hot, or fail to activate only one dispenser. Does the valve color (blue vs green) matter? No — the blue and green valve body colors are simply the result of different production runs at the factory. Both colors are the same part number (W11165546) with identical electrical specifications, port configuration, thermistor, and dimensions. Either color will function correctly in your washer. There is no functional difference between the two. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with 4 solenoid coils and an integrated thermistor to match the electrical specifications and port configuration of the original W11165546 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH23X29553 Washer Water Valve The XPARTCO WH23X29553 is an aftermarket replacement water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA. As an aftermarket replacement, the WH23X29553 is built to OEM-equivalent quality standards. Quick Answer The XPARTCO WH23X29553 Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces AP6983554, PS12743643, EAP12743643, 33090202, 0024000126GA. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering. Common Problems This Part Fixes Washer not filling with water, or filling only partially Washer fills much more slowly than it used to Water leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW GFW655SSV0WW PFW870SPV0RS PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match GE's factory-specified solenoid design and flow rate ABS plastic body with stainless steel components for corrosion resistance Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH23X29553 Part Type Washer Water Inlet Valve OEM Part Number WH23X29553 Condition Aftermarket Replacement Brand GE Application Front-Load Washers Body Material ABS plastic Component Material Stainless steel Quantity 1 valve Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I remove the front control panel without breaking it? Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair. I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal? Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand. Is this the same as WH23X29538? The numbers look almost identical. No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, flow rate, and connection type of the original WH23X29553 valve used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11399437 Genuine OEM Washer Drain Pump Replaces Part Numbers: AP6974144, PS12731241 Description: This Drain Pump is a Genuine OEM part for select Maytag, Kenmore, Whirlpool washer models. It is responsible for circulating water through the washing machine during all cycles. The pump draws water from the tub and dispenses it through the water supply hoses to soak, scrub, and rinse clothes.  

Read more less

AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly The AAN73209838 is a genuine LG OEM combined drain pump and cabinet base assembly for LG washers. This assembly bundles the washer's drain pump — which pumps water out of the drum and through the drain hose at the end of each cycle — together with the cabinet base structure it's mounted to. Because these two components ship together as one assembly, replacing this part addresses both the drain pump function and the base structure it sits in at the same time. Common causes of failure include a worn or jammed drain pump motor, or physical damage or corrosion to the cabinet base itself over years of use. A failing assembly typically shows up as the washer failing to drain, unusual noise during the drain phase, or water leaking from underneath the unit. Quick Answer The AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly fixes LG washers that won't drain, make unusual noise during the drain phase, or are leaking water from underneath the unit. Combined drain pump and cabinet base assembly. This is a larger, heavier assembly than a standalone drain pump — installation involves more disassembly than a simple pump swap. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain phase of the cycle Water leaking from underneath the washer Cycle stalling or failing to advance past the drain step Visible damage or corrosion to the cabinet base structure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AAN73209838, 4873470, 4985882, AHA75673401, AP6991753, AP6991765, EAP12580277, EAP16222263, FIX16222263, PS12580277, PS16222263, ALG51685, PD00091778 We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This drain pump and cabinet base assembly is compatible with select LG top-load washers, including model numbers such as WT7060CW, WT7100CW, WT7250CW, WT7300CV, T1780WFHT, and T1789EFH5T/T1789EFH5U/T1789EFHT/T1789EFHKD variants. Note: This is a combined assembly, not a standalone drain pump — if your washer only needs the pump replaced and the cabinet base is intact, ask our support team whether a standalone pump option is available for your model before ordering this larger assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified pump and base assembly Combined drain pump and cabinet base assembly in a single part Resolves "won't drain," "noisy drain phase," and "leaking underneath the washer" symptoms Direct drop-in replacement — matches the original mounting and hose connections Compatible with a range of LG top-load washer models Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AAN73209838 Part Type Washer Drain Pump & Cabinet Base Assembly Condition Genuine OEM Brand LG Application Top-Load Washers Function Pumps water from the drum through the drain hose; provides the cabinet base structure Repair Difficulty Moderate to Hard — larger assembly than a standalone pump Quantity 1 combined assembly Compatible Brand LG Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Remove Standing Water First Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Because this is a combined pump and cabinet base assembly rather than a standalone pump, access typically requires tipping the washer back or removing more of the cabinet than a simple pump swap — check your model's service diagram for the exact disassembly sequence, since it varies by model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old assembly, remove the fasteners securing it to the washer frame, and carefully remove it, noting how the base supports the rest of the cabinet. Install the new AAN73209838 assembly in the same position, reconnect the drain hose connections securely, reconnect the electrical connector fully, and secure all mounting fasteners. Reassemble the cabinet in reverse order, restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, socket set, pliers, towels or a small cup for removing standing water, work gloves. Frequently Asked Questions Do I need this whole assembly, or is there a smaller drain pump option for my model? Some LG washer models offer a standalone drain pump as a separate, smaller part, while others require this combined pump-and-base assembly because the two are integrated on that particular platform. Check with our support team using your model number to confirm whether a standalone pump is available for your washer before ordering this larger assembly, since it can save you time and cost if a smaller part fits your model. Why is this repair more involved than a typical drain pump replacement? Because this part includes the cabinet base structure along with the pump, accessing and replacing it typically involves more disassembly than swapping a standalone pump alone — you're not just disconnecting a pump, you're also working with part of the washer's supporting frame. Budget more time for this repair than you would for a simple pump-only replacement, and consider having a second person help support the cabinet during removal and installation. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, hose connections, and cabinet base mounting configuration of the assembly originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP697772 Dryer Blower Wheel The WP697772 is a genuine OEM blower wheel from Whirlpool for Whirlpool-built dryers and washer-dryer combos sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral names. The blower wheel attaches to the drive motor shaft and moves air over the heat source, through the drum, and out the exhaust vent. When the wheel wears, cracks, loses a fin, or comes loose on the shaft, the dryer gets noisy and airflow drops, so clothes take longer to dry. This is a genuine OEM part, not an aftermarket equivalent, so the fit and balance match the original. If your dryer is only noisy, check the blower for lint buildup first, since a clogged wheel can sound like a failing one. Quick Answer The Genuine OEM WP697772 Blower Wheel fixes a Whirlpool-built dryer that is noisy, has weak airflow, or takes too long to dry because the blower wheel is worn, cracked, or damaged. Genuine OEM from Whirlpool. Classic symptom: a rattling, thumping, or squealing noise from the back of the dryer, with damp clothes at the end of a normal cycle. Common Problems This Part Fixes Dryer noisy, with rattling or thumping from the blower area Weak airflow, or clothes taking too long to dry Visibly cracked, chipped, or broken blower fins Blower wheel loose or slipping on the motor shaft Wheel worn out over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This blower wheel replaces the following part numbers: WP697772, WPW10211915, 697772, W10211915, 687613, AP6010627, AWP48289,EAP11743811,  FIX11743811, OEM18031890, PD00003053, PS11743811 These are Whirlpool's un-prefixed and earlier numbers for this blower wheel. If your old wheel or parts diagram shows any of them, match against this list. Compatibility This blower wheel is listed for dryers and washer-dryer combos from: Whirlpool, including CEE2760KQ0, WED9470WW1, and WED9400ST1 Kenmore, including 11060052990, 11060056990, and 10687884100 Maytag, including YMEDX700XL0 and MGDX700AG0 KitchenAid, Amana, Crosley, Inglis, and Admiral Note: The model list above is only a sample, since this wheel fits many more models. Confirm fit by matching the number on your old wheel or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM Whirlpool blower wheel, not an aftermarket equivalent Restores quiet, full airflow through the drum and exhaust Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers and combos Straightforward replacement, typically 15–60 minutes with hand tools Product Specifications Part Number WP697772 OEM Part Number WP697772 Part Type Dryer Blower Wheel Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Family Dryers & Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Wear work gloves. Following your model's service guide, remove the front cover to reach the blower housing, then the back cover to access the motor shaft. Hold the motor shaft steady while you unscrew the retaining nut and pull off the old wheel. Reviewers report that the nut is left-hand threaded on these dryers, so check the thread direction before forcing it. Thread the new wheel on while holding the shaft, tighten it, and replace the covers. Clean the blower housing and exhaust duct of lint while you have the dryer open, and inspect the new wheel on arrival for damage. Frequently Asked Questions My dryer is noisy. Is this the part I need? Possibly. Before replacing the wheel, check whether it is clogged with lint, which can cause noise and imbalance. If the wheel is clean but cracked, chipped, or loose on the shaft, replace it. Also check the drum rollers and idler pulley, which can make similar sounds. Is the nut on the shaft left-hand threaded? Reviewers report that it is on these dryers, so turn it the opposite way to a normal nut when removing the old wheel. Check on your dryer before applying force. My old wheel is marked 697772 or W10211915. Will this work? Yes. Both numbers are on the Replaces list. If you're unsure, contact our support team with your model number and we'll confirm. Is this a genuine Whirlpool part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6501KW2001B Washer Rotor Positioning Sensor The XPARTCO 6501KW2001B is an aftermarket replacement rotor position sensor (RPS) compatible with a wide range of LG and Kenmore direct-drive front-load washers. This 5-pin Hall effect sensor mounts to the motor stator and monitors the speed and rotational direction of the motor rotor, feeding that data back to the control board so it can properly manage spin speed, direction changes during wash/rinse agitation, and load balancing. When this sensor fails or reads inaccurately, the control board loses the feedback it needs to run the motor correctly, and the washer commonly throws an "LE" (motor/rotor position) error code, fails to spin or agitate, or runs unusually long cycles as it struggles to detect motor movement. Built with PBT-GF30 housing and black epoxy potting for durability in the motor compartment. It directly replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 6501KW2001B Washer Rotor Positioning Sensor fixes LG and Kenmore (LG-built) direct-drive front-load washers throwing an "LE" error code, failing to spin or agitate, or running abnormally long cycles. 5-pin Hall effect sensor, PBT-GF30 housing, black epoxy potting. Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, 3282954. Classic symptom: washer displays "LE" and stops mid-cycle, or won't spin at all. Common Problems This Part Fixes Washer displays an "LE" (motor/rotor position) error code Tub fails to spin or agitate during the wash cycle Washer struggles to detect load movement, resulting in abnormally long cycle times Motor runs erratically or stalls mid-cycle Washer stops partway through a cycle without completing Inconsistent or failed direction changes during agitation Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This rotor position sensor directly replaces the following OEM and cross-reference part numbers: 6501KW2001B, 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, ALG52243, AP4457567, AP5973402, EAP11706506, 3282954, PD00059513, PS3529185, PS11706506 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This rotor position sensor is compatible with select LG-built direct-drive front-load washers, including: LG front-load washers (including WM1814CW, WM2010CW, WM2016CW, WM3455HW) Kenmore front-load washers (select LG-built models, including WD-3243RHD, WD-3245RHD, WD-3274RHD) Important: Do not confuse this with 6501KW2002B, which is a different, non-interchangeable rotor position sensor used on other LG washer platforms. Some newer LG models also integrate the Hall sensor directly into the motor stator assembly (such as AJB73816004) rather than using a standalone sensor like this one. Always verify your appliance model number before ordering, and check your parts diagram to confirm whether your model uses a standalone sensor. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement LG/Kenmore washer rotor position sensor (Hall effect, 5-pin) Resolves "LE error code," "won't spin," "won't agitate," and "long cycle time" symptoms Monitors motor rotor speed and rotational direction for accurate control board feedback PBT-GF30 housing with black epoxy potting for durability in the motor compartment Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954 Compatible with select LG and Kenmore (LG-built) direct-drive front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP6501KW2001B OEM Part Number 6501KW2001B Part Type Washer Motor Rotor Position Sensor Condition Aftermarket Replacement Sensor Type Hall Effect, 5-Pin Housing Material PBT-GF30 with black epoxy potting Application LG-Built Direct-Drive Front-Load Washer Motor Assembly Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning. Access the motor compartment, typically by removing the rear panel of the washer. Locate the rotor position sensor mounted to the motor stator near the rotor. Photograph the wiring before disconnecting, then unplug the sensor's connector from the wiring harness. Remove the mounting screw(s) or clip holding the sensor to the stator and remove the old sensor. Install the new 6501KW2001B sensor in the same position, taking care to seat it at the correct distance/orientation from the rotor magnets, and secure it. Reconnect the wiring harness connector, matching your photos. Reinstall the rear panel, restore power, and run a test cycle to confirm the washer spins and agitates normally without triggering an LE error code. Tools needed: nut driver or screwdriver, needle-nose pliers (for wiring connectors). Frequently Asked Questions My washer shows an "LE" error code — is this the part I need? This is one of the most common causes of an LE (motor/rotor position) error on LG and LG-built Kenmore washers. If your washer displays LE and stops mid-cycle or won't spin, this sensor is a likely culprit. That said, LE errors can also stem from the control board or a damaged wiring harness between the sensor and the board, so if replacing the sensor doesn't resolve the error, those components are the next things to inspect. Is this the same as the 6501KW2002B sensor? No — 6501KW2001B and 6501KW2002B are different, non-interchangeable rotor position sensors used on different LG washer platforms. Confirm your exact part number from your appliance's parts diagram before ordering, since these two are easy to mix up by their similar naming. My LG washer's parts diagram doesn't show a separate rotor position sensor — why? Some newer LG models integrate the Hall sensor directly into the motor stator assembly (such as part AJB73816004) rather than using a standalone sensor like this one. If your model doesn't list a standalone sensor, check whether your repair requires the full stator assembly instead. Contact our support team with your model number if you're unsure which one applies to your washer. Do I need any special tools to install this? No special tools — a nut driver or screwdriver to access the rear panel and remove the sensor's mounting screw(s), plus needle-nose pliers to help with the wiring connector. The main thing to get right is reinstalling the new sensor at the same position and orientation relative to the rotor as the original. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

V-156-1C25 Micro Limit Switch Contact Type: SPDT 1NO 1NC Actuator Type: 1.1" Long Hinge Roller Lever Rating: 15A 125 250VAC Lever Length: 1.1" Long Hinge Roller Lever Rating: 15A,1/2HP, 125 250VAC; 0.6A,125VDC; 0.3A, 250VDC   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

285751 Washer Genuine Agitator Dog Cam Kit Replaces Part Numbers:  285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624. Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10411934 Range Genuine OEM Surface Element Switch – Compatible with Whirlpool, Maytag & KitchenAid Ranges Product Description Restore precise burner temperature control with the WPW10411934 Range Genuine OEM Surface Element Switch. This Genuine OEM switch is engineered by the original manufacturer to control the heat output of electric surface elements. A faulty surface element switch can cause burners to stay on high, not heat at all, or cycle inconsistently. Replacing it with this authentic OEM part ensures proper electrical performance, safe operation, and factory-level reliability. This part is a Genuine OEM component, manufactured to exact specifications for fit, durability, and long-term performance. Replaces Part Numbers WPW10411934, W10411934, 4446483, PD00033778, EAP11754410, AP6021089, PS11754410. Compatibility This Genuine OEM surface element switch fits select Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore (Whirlpool-manufactured) electric ranges. Common compatible models include (but are not limited to): Whirlpool WFE515S0ES Maytag MER8800FZ KitchenAid KERA205PB Always verify your range’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🏭 Genuine OEM Part – Manufactured to original factory specifications 🔥 Accurate Heat Regulation – Restores proper burner temperature control ⚡ Safe Electrical Operation – Designed for correct voltage and load handling 🎛️ Smooth Adjustment – Ensures responsive burner control 🔧 Exact Fit & Direct Replacement – No modifications required 📐 Product Specification Part Number: WPW10411934 Component Type: Surface Element Control Switch Voltage: 240V Application: Electric range surface burner control Mounting: Shaft-mounted behind control panel OEM Status: Genuine OEM 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Disconnect power at the breaker before servicing the range to avoid electrical shock. Basic Steps: Turn off power to the range at the breaker. Remove the control knob and access the control panel. Label and disconnect wires from the old switch. Remove mounting screws and remove the old switch. Install the new WPW10411934 Genuine OEM switch. Reconnect wiring, reassemble the control panel, and restore power. Test burner operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🏭 Genuine OEM Appliance Part 🚚 Free Shipping on All Orders 🔄 30-Day Return Policy Restore factory-level burner control and safe cooking performance — Add to Cart Now with confidence!

Read more less