XPARTCO H150 Furnace Silicon Nitride Rod Ignitor
The H150 universal gas furnace igniter come with a 1.95-inch ceramic nitride heating element, a 1.25-inch ceramic insulator, a 304 stainless steel bracket, and a 15.5-inch high temperature resistant wire(20 AWG). Voltage: 120V±10%-15%, 50/60HZ. Power Rating: 150W. Cold resistance: 9-17Ω. At 120V furnace igniter H150 can reach 1200 degrees in a short time
The H150 universal furnace igniter replacement can be used in a wide range of machines and is the perfect replacement for silicon carbide ignitors in water heater boilers and gas forced-air furnaces, replacing more than 180 types of ignitors and covering nearly 90% of all applications. Such as stoves, furnace, warm air motion, gas ignition, hot surface igniter, infrared light source, pool heater, boiler, etc
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO WB13K21 Gas Oven Flat Igniter with Harness
The XPARTCO WB13K21 is an aftermarket replacement flat-style gas oven igniter with harness compatible with select GE, Hotpoint, RCA, and Kenmore gas ranges and ovens. The oven igniter is a silicon carbide heating element mounted inside the oven next to the burner. It serves a dual purpose: it draws electrical current through the oven safety valve to hold it open, and it heats to ignition temperature to light the gas burner. The igniter must draw sufficient current — typically 3.2–3.6 amps — to hold the safety valve fully open. A weakened igniter that draws too little current will glow but never fully open the gas valve, preventing the burner from lighting.
This flat-style igniter draws 3.4–3.6 amps at 115V. The ceramic block measures 1-1/2" L, with an overall bracket/cage measuring 3-3/4"L x 2-1/8"W x 13/16"H. The harness and plug extend approximately 7-7/8" from the igniter body with female pin connectors and a double wing mounting bracket. It can be used as a bake or broil igniter replacement on compatible models. It directly replaces WB13K21, WB13K12, WB13K13, WB13K14, WB13K0012, WB13K0013, WB13K0014, WB13K0021, WB13K10009, WB13K10026, IG21, 2494, AP2020569, AH231280, EA231280, EAP231280, PS231280, and PD00001023. Note: if the connector does not match your range's harness, cut the connector and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO WB13K21 Gas Oven Flat Igniter with Harness fixes GE, Hotpoint, RCA, and Kenmore gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat igniter, 3.4–3.6A, 115V. 1-1/2" ceramic block, 3-3/4"L x 2-1/8"W x 13/16"H bracket. 7-7/8" harness with female pins. If connector doesn't match, splice with porcelain wire nuts. Replaces WB13K21, WB13K12, WB13K13, WB13K14, IG21, AP2020569, AH231280, PS231280.
Common Problems This Part Fixes
Oven not heating — igniter not reaching operating temperature or gas valve not opening
Igniter glows orange but the gas burner never lights
Oven takes more than 90 seconds to ignite after turning on
Oven preheats very slowly — weak igniter no longer drawing enough current to fully open the gas valve
Gas smell when oven is turned on but burner does not light
Igniter visibly cracked, broken, or burned out
Bake or broil function not working on compatible models
Replaces Part Numbers
This oven igniter directly replaces the following OEM and cross-reference part numbers:
WB13K21, WB13K0012, WB13K0013, WB13K0014, WB13K10009, WB13K10026, WB13K12, WB13K13, WB13K14, 2494, AH231280, AP2020569, AGE21391, EA231280, EAP231280, PD00001023, PS231280.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This oven igniter is compatible with select gas ranges and ovens from the following brands:
GE gas ranges and ovens (select models)
Hotpoint gas ranges and ovens (select models)
RCA gas ranges and ovens (select models)
Kenmore / Sears gas ranges (select GE-built models)
Note: Can be used for both bake and broil igniter replacement on compatible models. If the two-pin connector does not match your range's existing harness connector, cut the connector off the new igniter and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner due to heat. Always verify your model number before ordering.
Key Features
Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the safety valve to open it and allow gas to flow to the burner
Draws 3.4–3.6 amps at 115V — correct amperage range to reliably open the GE oven gas safety valve
Ceramic block: 1-1/2" L; bracket/cage: 3-3/4"L x 2-1/8"W x 13/16"H
Harness and plug extend approximately 7-7/8" from the igniter body
Female pin connectors with double wing mounting bracket — quick install on compatible models
Can replace bake or broil igniter on compatible models
If connector does not match: cut and splice using porcelain wire nuts (included) — never use standard plastic wire nuts near the burner
Replaces over 18 older GE oven igniter cross-reference part numbers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
XPWB13K21
Part Type
Gas Oven Flat Igniter with Harness (Hot Surface Igniter)
Condition
Aftermarket Replacement
Application
Gas Ranges and Ovens (bake and broil)
Igniter Style
Flat (cageless silicon carbide element)
Amperage Draw
3.4 – 3.6 Amps
Voltage
115V AC
Ceramic Block Length
1-1/2 inches
Bracket / Cage Dimensions
3-3/4"L x 2-1/8"W x 13/16"H
Harness / Lead Length
Approximately 7-7/8 inches from igniter body
Connector Type
Female pins, two-pin quick-disconnect (splice with porcelain nuts if needed)
Mounting
Double wing bracket
Material
Silicon carbide / Ceramic / Metal / Plastic
Compatible Brands
GE, Hotpoint, RCA, Kenmore
Installation Notes
⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are secure. If you are not comfortable working on gas appliances, have this part installed by a qualified technician.
⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to skin oils. Do not touch the igniter element with bare hands — oils from skin will create hot spots that prematurely burn the igniter. Handle only by the bracket, harness, and mounting wings. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector at the connection point inside the oven. Remove the two screws securing the mounting bracket. If the new igniter's connector matches the harness, plug it in directly. If it does not match, cut the connector from the new igniter and use the included porcelain wire nuts to splice the wires to your range's existing harness — do not use plastic wire nuts. Mount the new igniter using the double wing bracket and two screws. Reinstall the oven bottom panel, restore gas and power, and run a bake cycle to confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, socket set, work gloves.
Frequently Asked Questions
My igniter glows but the burner never lights — is it the igniter?
Yes, almost certainly. A gas oven igniter that glows orange or red but does not light the burner is a classic sign of a weakened igniter. The igniter must draw enough electrical current — typically 3.2 amps or more — to hold the gas safety valve fully open. As the silicon carbide element ages, its resistance increases and it draws progressively less current. When the current drops below the threshold needed to hold the valve open, the valve never fully opens, even though the igniter appears to glow. If the igniter glows for more than 90 seconds without lighting the burner, it needs to be replaced.
Why can't I use plastic wire nuts to splice the igniter wires?
The igniter is located inside the oven cavity, directly adjacent to the gas burner, where temperatures during operation can easily exceed what standard plastic wire nuts are rated for. Plastic wire nuts can melt or deform at oven operating temperatures, potentially exposing bare wire connections and creating a short circuit or fire hazard. Porcelain wire nuts are specifically rated for high-temperature applications and are the only safe connector to use when splicing igniter wires near the oven burner. Always use porcelain — never plastic — for any wiring connection inside the oven cavity.
Can this igniter be used for both bake and broil?
Yes — on compatible GE, Hotpoint, and Kenmore models, the WB13K21 can be used to replace both the bake igniter (lower burner) and the broil igniter (upper burner), as both igniters use the same part number and specifications on these models. Verify your range's parts diagram to confirm that both igniters use the WB13K21 before ordering for the broil position.
How do I test if the oven igniter has failed?
The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, it has weakened. You can also use a multimeter — disconnect the igniter wires and measure resistance. A working WB13K21-style igniter typically reads between 40 and 90 ohms at room temperature (a lower resistance draws more current; a very high resistance means the element is nearly failed). An open circuit (infinite resistance) means the element has burned through completely. If the igniter does not glow at all when the oven is turned on, it has completely failed electrically.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original WB13K21 oven igniter.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 316489403 Gas Oven Igniter
The XPARTCO 316489403 is an aftermarket replacement gas oven igniter compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges, ovens, and stoves. The oven igniter is the component that lights the gas burner — when you set the oven to bake or broil, electricity flows through the igniter, heating it until it glows bright orange. This heat both ignites the gas and draws enough current to open the gas safety valve, releasing gas to the burner. When the igniter weakens with age, it may still glow but no longer pull enough current to open the safety valve — so the oven fails to light, takes a long time to heat, or heats unevenly.
This is a flat-style, open-cage igniter. Electrical rating: 3.2–3.6 amps, 120V AC. Made of silicon carbide and ceramic for high heat resistance and long service life. Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; the lead and plug measure approximately 16" long. Includes the flat-style igniter assembly with bracket and leads/plug. It directly replaces 316489403, 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063. Important: the igniter element is fragile — handle it only by the bracket, never by the element itself. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 316489403 Gas Oven Igniter fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ovens that won't light, take too long to heat, heat unevenly, or where you smell gas because the igniter is too weak to open the safety valve. Flat-style open-cage igniter. 3.2–3.6A, 120V AC. Silicon carbide/ceramic. Overall 3-1/2"L x 1-3/4"W x 13/16"H, 16" lead. Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, PS2364063. Handle by the bracket only — the element is fragile.
Common Problems This Part Fixes
Oven won't light or heat at all — igniter too weak to open the gas safety valve
Oven takes a long time to reach temperature — igniter glowing but drawing insufficient current
Oven heats unevenly or undercooks food — weak or slow ignition
Igniter glows but the burner never ignites — classic sign of a degraded igniter
Igniter doesn't glow at all — burned out or open circuit (no power reaching the burner)
Gas smell when the safety valve opens but the burner doesn't light
Oven runs erratically or won't maintain temperature
Igniter visibly cracked, broken, or with a damaged element
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This gas oven igniter directly replaces the following OEM and cross-reference part numbers:
316489403, 5304508786, 7316489403, Model 501RB, AH2364063, EA2364063, EAP2364063, AFR16172, AP4433236, PD00000756, PS2364063.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: on some models this is the broil (upper) igniter, and the bake (lower) igniter is a different part — see the FAQ below on bake vs broil igniters.
Compatibility
This gas oven igniter is compatible with select gas ranges, ovens, and stoves from the following brands:
Frigidaire gas ranges and ovens — including many Frigidaire Gallery models (LGGF, FGGF, FFGF series and related)
Electrolux gas ranges and ovens (select models)
Crosley gas ranges and ovens (select models)
Gibson gas ranges and ovens (select models)
Kelvinator gas ranges and ovens (select models)
Tappan gas ranges and ovens (select models)
White-Westinghouse gas ranges and ovens (select models)
Ikea gas ranges and ovens (select Frigidaire-built models)
Kenmore / Sears gas ranges and ovens (select Frigidaire-built models, including 790-series)
Note: This igniter fits specific models — always verify against your appliance's model number before ordering. On ranges with two igniters (a bake igniter and a broil igniter), confirm which one you need (see the bake-vs-broil FAQ below). Contact our support team with your model number if you're unsure.
Key Features
Gas oven igniter — heats up to ignite the burner and draws current to open the gas safety valve
Flat-style, open-cage design
Resolves "won't light," "slow to heat," "uneven heating," "glows but won't ignite," and "gas smell" symptoms caused by a weak or failed igniter
Electrical rating: 3.2–3.6 amps, 120V AC
Silicon carbide and ceramic construction — high heat resistance and long service life
Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; lead and plug approximately 16" long
Includes the flat-style igniter assembly with bracket and leads/plug (some kits include ceramic wire nuts)
Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063
Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
316489403
Part Type
Gas Oven Igniter (Flat Style, Open Cage)
Condition
Aftermarket Replacement
Application
Gas Ranges, Ovens, and Stoves (Frigidaire platform)
Amperage
3.2–3.6 Amps
Voltage
120V AC
Igniter Style
Flat, open cage
Overall Dimensions
3-1/2"L x 1-3/4"W x 13/16"H
Ceramic Block
1.5" L
Lead Length
Approximately 16"
Material
Silicon carbide / ceramic / metal
Color
Almond / White / Gray
Includes
Igniter assembly with bracket and leads/plug
Compatible Brands
Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, Kenmore
Installation Notes
⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Shut off the gas supply to the range at the shutoff valve and disconnect electrical power at the breaker before beginning any repair. After installation, if you smell gas at any point, leave the area immediately and contact your gas utility provider. If you're not comfortable working around gas components, have this repair done by a qualified appliance technician. Improper gas appliance repairs can cause fire, explosion, or carbon monoxide hazards.
⚠️ Handle the Igniter by the Bracket Only — The Element Is Fragile Disconnect power at the breaker and shut off the gas supply before beginning. Wear work gloves and safety glasses. The silicon carbide igniter element is extremely fragile and cracks easily — handle the new igniter only by its metal bracket, never by touching the element itself. Skin oils and any impact can shorten its life or break it. Locate the igniter: the bake igniter is beneath the oven floor panel (remove the oven racks, then the floor panel, and on some models the bottom drawer for access), while the broil igniter is mounted near the top of the oven cavity. Photograph the wiring connection before disconnecting. Disconnect the old igniter's wire leads at the connector (they're often joined with ceramic wire nuts). Remove the screws securing the old igniter bracket and lift it out. Install the new 316489403 by securing its bracket in the same position and orientation, then connect the wire leads (use the included or existing ceramic wire nuts — regular wire nuts can't handle the heat). Route the leads away from the burner flame. Restore gas and power. Test by setting the oven to bake (or broil, if that's the igniter you replaced) — the igniter should glow bright orange within a minute or so, and the burner should light within about 60–90 seconds. Tools needed: Nut driver, Phillips screwdriver, work gloves, safety glasses.
Frequently Asked Questions
My igniter glows but the oven won't light — do I still need to replace it?
Yes — this is actually the most common way an oven igniter fails, and it's counterintuitive. The igniter has two jobs: to get hot enough to ignite the gas, AND to draw enough electrical current to open the gas safety valve. As an igniter ages, it can still glow (so it looks like it's working) but weaken to the point where it no longer pulls enough current to open the safety valve — so no gas is released and the burner never lights. If your igniter glows orange but the burner doesn't light within about 90 seconds, the igniter is weak and needs replacement. A good rule of thumb: if it takes more than 90 seconds from glow to flame, the igniter is on its way out.
Is the 316489403 the bake igniter or the broil igniter?
This is an important distinction, and there's genuine confusion in the industry about it. On many Frigidaire gas ranges, the 316489403 is used as the broil (upper) igniter with an approximately 14–16" lead, while the bake (lower) igniter is a different part — 5304506545 (which superseded 316489404) — often with a shorter lead. However, some sources and parts diagrams list them differently or even reversed, and on some models the 316489403 serves the bake position. The safest approach: look up YOUR specific model number to confirm which igniter you need, and compare your old igniter's lead length to the replacement. If your old igniter's leads reach a connector far from the igniter (14–16"), the 316489403 with its 16" lead is likely correct. Contact our support team with your model number and we'll confirm.
Why do I smell gas when I try to use the broiler?
If you smell gas when the broiler's safety valve opens but the burner doesn't light, it usually means the igniter isn't getting hot enough (or drawing enough current) to ignite the gas that's being released — so raw gas escapes before shutting off. This points to a weak igniter. To confirm which part is at fault: with the gas off, do a voltage test at the oven safety valve on the broil side — you should read between 3.0 and 3.3 VAC. If the voltage is correct but the burner won't light, the igniter is the problem. If there's no proper voltage, or the burner tube has spider webs or debris blocking it, address those first. Also inspect the gas supply tube from the safety valve to the burner for damage or loose connections.
Why do I need to handle the igniter so carefully?
The igniter's heating element is made of silicon carbide, a material that's excellent at withstanding heat but is brittle and cracks easily from impact or flexing. Even touching the element with bare fingers can leave oils that create hot spots and shorten its life, and a small bump can crack it invisibly, causing premature failure. Always handle the new igniter by its metal bracket, never by the element or the ceramic block. When installing, be careful not to bump the element against the oven walls or burner. This care is the single biggest factor in whether your new igniter lasts years or fails early.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from silicon carbide and ceramic to match the electrical specifications (3.2–3.6A, 120V AC), flat open-cage style, dimensions (3-1/2"L x 1-3/4"W x 13/16"H, 16" lead), and ignition function of the original 316489403 gas oven igniter used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W11590294 Gas Oven Igniter
The XPARTCO W11590294 is an aftermarket replacement flat-style silicon carbide gas oven igniter compatible with select Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges in the WFG, AGR, VRGW, and related series. The oven igniter is a silicon carbide heating element mounted next to the oven burner tube. When a bake or broil cycle is started, the igniter draws electrical current through the gas safety valve, which holds the valve open — and simultaneously heats to ignition temperature to light the gas. The igniter must draw at least 3.2 amps to hold the gas valve fully open; as the silicon carbide element ages and weakens, it draws progressively less current, causing the oven to take too long to light, not light at all, or glow without ever opening the gas valve.
This flat-style igniter is rated 3.3–3.6 amps at 120V and measures approximately 4" wide x 1" high. It features a silicon carbide element, high-temperature ceramic housing, and metal bracket. The current part number W11590294 directly supersedes W11208965, W11613927, and W11506321 — all four are the same igniter across successive production revisions. It also replaces 4977065, AP7193166, PS16744629, and EAP16744629. Pre-attached wire connectors included. Note: do not touch the silicon carbide element with bare hands — skin oils cause premature burnout. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W11590294 Gas Oven Igniter fixes Whirlpool-family gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat silicon carbide igniter, 3.3–3.6A, 120V, approx. 4"W x 1"H. Do not touch element with bare hands. Replaces W11208965, W11613927, W11506321, 4977065, AP7193166, PS16744629. Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and more.
Common Problems This Part Fixes
Oven not heating — igniter not reaching operating temperature or gas valve not opening
Igniter glows orange or red but the oven burner never lights
Oven takes more than 90 seconds to ignite — igniter too weak to fully open the gas valve
Oven preheats very slowly — weakened igniter limiting gas valve opening
Gas smell when oven is turned on but burner does not light
Igniter visibly cracked, broken, or burned out
Bake or broil function not working on compatible models
Replaces Part Numbers
This oven igniter directly replaces the following OEM and cross-reference part numbers:
W11590294, W11208965, W11506321, W11613927, AP7193166, AWP45526, EAP16744629, PD00083398, PS16744629.
W11590294 is the current production part number superseding W11208965, W11613927, and W11506321 — all four are the same igniter. If your parts diagram shows any of these numbers, this replacement is correct. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This oven igniter is compatible with select gas ranges and ovens from the following brands and series:
Whirlpool gas ranges — WFG320 series (WFG320M0MB0, WFG320M0MS0, WFG320M0MW0 and related models)
Whirlpool gas ranges — WFG505 series (WFG505M0BS4, WFG505M0BW3, WFG505M0MB0, WFG505M0MS0, WFG505M0MW0 and related models)
Amana gas ranges — AGR4203 series (AGR4203MNB0, AGR4203MNW0 and related models)
Amana gas ranges — AGR6303 series (AGR6303MMB0, AGR6303MMW0 and related models)
Crosley gas ranges — VRGW series (VRGW3150RB0, VRGW3150RW0, VRGW3162RB0, VRGW3162RS0, VRGW3162RW0 and related models)
Maytag gas ranges (select models)
KitchenAid gas ranges (select models)
Jenn-Air gas ranges (select models)
Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the gas safety valve to hold it open so gas can flow to the burner
Draws 3.3–3.6 amps at 120V — correct amperage range to reliably open the oven gas safety valve on compatible models
Dimensions: approximately 4" wide x 1" high
Silicon carbide element, high-temperature ceramic housing, metal mounting bracket
Pre-attached wire connectors included — direct plug-in installation on compatible models
Current production part superseding W11208965, W11613927, and W11506321
Do not touch the silicon carbide element with bare hands — skin oils cause premature burnout
Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and related brands
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
XPW11590294
Supersedes
W11208965, W11613927, W11506321
Part Type
Gas Oven Flat Igniter (Hot Surface Igniter)
Condition
Aftermarket Replacement
Application
Gas Ranges and Ovens
Igniter Style
Flat silicon carbide element
Amperage Draw
3.3 – 3.6 Amps
Voltage
120V AC
Dimensions
Approximately 4" W x 1" H
Material
Silicon carbide / Ceramic / Metal / Plastic
Color
White / Silver
Connector
Pre-attached wire connectors
Handling Note
Do not touch element — skin oils cause premature burnout
Compatible Brands
Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Gas Appliance Safety Warning This part is installed in a gas range. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure.
⚠️ Handle With Care — Do Not Touch the Igniter Element The silicon carbide igniter element is fragile and sensitive to skin oils. Handle only by the bracket and wiring — never touch the silicon carbide element itself. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel to expose the burner assembly. Locate the old igniter mounted next to the oven burner tube. Disconnect the igniter's wire connectors and remove the two mounting screws securing the bracket. Note the wire routing inside the range cavity before removing — be careful not to let the burner wires fall back into the range body. Connect the new W11590294 igniter's pre-attached connectors to the matching wires from the range. Mount the new igniter in the same position with the two bracket screws. Reinstall the oven bottom panel and racks. Restore gas and power, then run a bake cycle and confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
What is the relationship between W11590294, W11208965, W11613927, and W11506321?
These are all part numbers for the same gas oven igniter across successive production revisions by Whirlpool. W11506321 was an earlier version, W11613927 and W11208965 were subsequent updates, and W11590294 is the current production number. All four are the same flat silicon carbide igniter with the same specifications, dimensions, and function. If your range's parts diagram or old igniter shows any of these numbers, this replacement covers all of them.
My oven igniter glows but the burner never lights — is this the right part?
Yes — an igniter that glows but fails to light the burner is the most common symptom of a weakened igniter. The gas safety valve requires at least 3.2 amps of current draw through the igniter to hold it open. As the silicon carbide element ages, it draws less current — eventually reaching a point where it glows visibly but no longer draws enough current to fully open the gas valve. If the igniter glows for more than 90 seconds without the burner lighting, it needs replacement. The W11590294 is rated 3.3–3.6 amps, which is the correct range to reliably activate the safety valve on compatible models.
What is the difference between W11590294 and W11176454?
Both are flat silicon carbide oven igniters for Whirlpool-family gas ranges, but for different model series. The W11590294 is used on the WFG320, WFG505, and related entry-level Whirlpool and Amana gas ranges. The W11176454 (which replaces W10914411) is used on higher-end Whirlpool, Amana, and Maytag models across a broader range of WFG, MGR, and related series. They have the same amperage rating and igniter style but are not always interchangeable — always verify your model number before ordering to confirm which igniter is correct for your range.
How do I test if the oven igniter has failed?
The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, the igniter is too weak. For a more precise test, use a multimeter in resistance mode — disconnect the igniter and measure resistance across the element. A working W11590294-style igniter typically reads between 40–100 ohms at room temperature. An open circuit (infinite resistance) means the element has burned through completely. You can also test in operation by measuring current draw at the igniter circuit — a reading below 3.2 amps indicates the igniter is too weak to reliably open the gas valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original W11590294 gas oven igniter.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO MEE61841401 Gas Oven Igniter
The XPARTCO MEE61841401 is an aftermarket replacement oven burner igniter compatible with select LG and Kenmore gas ranges in the LDG, LRG, LSG, LSS, LTG, and LSR series. The igniter is a flat glow bar hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without ever lighting the burner.
This igniter draws 3.3–3.8 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F within approximately 60 seconds. The igniter body measures 3-1/2 inches long x 1-3/4 inches wide x 7/8 inches high, with a lead/plug assembly extending approximately 10-3/4 inches from the igniter. It includes a 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors to accommodate direct plug-in or spliced installation. Directly replaces OEM part numbers MEE61841401, MEE61841403, and MEE63084901.
Quick Answer
The XPARTCO MEE61841401 Gas Oven Igniter fixes LG and Kenmore gas ovens that won't heat, take too long to preheat, display error codes F9 or F11, or have an igniter that glows but never lights the burner. Flat glow bar style, silicon carbide. Draws 3.3–3.8A at 120V. Igniter body 3-1/2" L x 1-3/4" W x 7/8" H with 10-3/4" lead. Includes bracket and 2 porcelain wire connectors. Replaces MEE61841403 and MEE63084901.
Common Problems This Part Fixes
Oven not heating at all — gas is not igniting
Oven takes excessively long to preheat
Igniter glows orange or red but never lights the gas burner
Error codes F9 or F11 displayed on LG gas ranges
Gas smell when oven is turned on but burner does not light
Oven heats inconsistently or shuts off mid-cycle
Igniter burned out or visibly cracked or broken
Replaces Part Numbers
This oven igniter directly replaces the following OEM and cross-reference part numbers:
MEE61841401, MEE63084901, 1599783, MEE61841403, EAP3535362, ALG1385007, PD00001851, 095225468650, AH3535362, EA3535362, AP5214765, PS3535362.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This igniter is compatible with select gas ranges from the following brands and series:
LG gas ranges — LRG series (freestanding)
LG gas ranges — LDG series (freestanding)
LG gas ranges — LSG series (slide-in)
LG gas ranges — LSS series
LG gas ranges — LTG series
LG gas ranges — LSR series
Kenmore / Sears gas ranges (select LG-built models)
Compatible with both single and double oven models. Always verify your model number before ordering. Contact our support team if you're unsure.
Key Features
Flat glow bar hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner
Silicon carbide construction — superior heat resistance, high melting point, corrosion and oxidation resistant
Draws 3.3–3.8 amps at 120V AC — correct amperage range to open the LG gas safety valve
Operating temperature: 1,800°F – 3,100°F with approximately 60-second heat-up time
Igniter body: 3-1/2" L x 1-3/4" W x 7/8" H; lead/plug assembly: approximately 10-3/4" from igniter body
Plug-in installation — includes 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors for splicing if needed
Compatible with single and double oven models
Directly replaces MEE61841401, MEE61841403, and MEE63084901 — no modification required in most cases
Resolves error codes F9 and F11 on compatible LG gas ranges
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 10–20 minutes with basic hand tools
Product Specifications
Part Number
MEE61841401
Also Replaces
MEE61841403, MEE63084901
Part Type
Gas Oven Burner Igniter (Flat Glow Bar Hot Surface Igniter)
Condition
Aftermarket Replacement
Application
Gas Ranges and Ovens (single and double oven)
Igniter Style
Flat glow bar, cageless
Material
Silicon Carbide / Metal / Ceramic / Porcelain / Plastic
Colors
White / Black / Gray
Amperage Draw
3.3 – 3.8 Amps
Voltage
120V AC
Operating Temperature
1,800°F – 3,100°F
Heat-Up Time
Approximately 60 seconds
Igniter Body Dimensions
3-1/2" L x 1-3/4" W x 7/8" H
Lead / Plug Length
Approximately 10-3/4 inches from igniter body
Includes
Igniter, mounting bracket, 2-wire harness/plug, 2 porcelain wire connectors
Error Codes Resolved
F9, F11
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician.
⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to contamination. Do not touch the ceramic bar with bare hands under any circumstances — oils from skin will damage the element and significantly shorten its lifespan. Handle only by the bracket, wires, and plug. To install: unplug the range and shut off the gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector. Secure the new MEE61841401 igniter to the burner bracket with the mounting screws. If the plug is a direct match to your range's harness, plug it in. If not, cut the wires and use the included porcelain wire connectors to splice the new igniter to the existing wiring. Reinstall the oven bottom panel, restore gas supply and power, and run a test cycle. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
What is the difference between MEE61841401, MEE61841403, and MEE63084901?
These are all part numbers for the same LG flat glow bar oven igniter used across different model ranges and production runs. MEE63084901 is the earlier part number; MEE61841401 and MEE61841403 are updated versions. All three are interchangeable, and this aftermarket replacement is compatible with all of them.
How do I know if my oven igniter needs to be replaced?
The most common signs are the oven not heating at all, taking much longer than normal to preheat, or the igniter glowing orange but never lighting the gas burner. A healthy igniter glows bright orange and ignites the burner within about 60 seconds. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Error codes F9 or F11 on LG ranges can also indicate a failed igniter.
Do I need to splice the wires or does it plug straight in?
This igniter includes a 2-wire harness/plug for direct plug-in installation on most compatible LG models. If the connector does not match your range's existing harness, cut the old connector off and use the 2 porcelain wire connectors included in the kit to splice the new igniter to the existing wiring. Do not use standard plastic wire nuts — only porcelain connectors should be used near the oven burner due to the high heat involved.
What do error codes F9 and F11 mean on an LG range?
On compatible LG gas ranges, error code F9 typically indicates an oven heating failure, and F11 can indicate a shorted or failed igniter circuit. Both codes can be triggered by a weak or failed oven igniter. Replacing the MEE61841401 igniter resolves these error codes in many cases — though other causes such as a failed gas safety valve or control board issue should also be ruled out if the problem persists after replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from silicon carbide, metal, ceramic, and porcelain to match the electrical specifications and physical dimensions of the original MEE61841401 igniter.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10209656 Range Surface Igniter – Compatible with Whirlpool, Maytag, KitchenAid, and Kenmore Gas Ranges
Product Description
Restore reliable burner ignition with the XPARTCO W10209656 Range Surface Igniter. This high-quality aftermarket replacement provides the heat needed to ignite gas burners on your cooktop. A weak or failed igniter can cause burners not to light or take too long to ignite. Replacing it with this durable XPARTCO igniter restores instant ignition and safe cooking performance.
Replaces Part Numbers
WPW10209656, W10209656, 1468965, 98008959, 98012193, 98014514, 98014515, 98017561, 98017562, 98017917, W10112313, W10127479, AP6017135, PS11750430.
Compatibility
This replacement surface igniter is compatible with select Whirlpool, Maytag, KitchenAid, and Kenmore gas ranges.
Example compatible models include (but are not limited to): Whirlpool WFG320M0BS3, Maytag MGR6600FZ0, and Kenmore 665.75002100.
Always verify your range’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Compatible with Whirlpool-brand gas ranges
🔥 Reliable Ignition – Provides consistent spark for fast burner lighting
💰 Affordable Solution – Quality alternative to OEM parts at lower cost
🛠️ DIY Friendly – Installs easily with basic hand tools
🛡️ Fixes Common Issues – Solves burners not igniting or clicking without flame
📐 Product Specification
Part Number: W10209656
Component Type: Gas Range Surface Igniter
Material: High-temperature ceramic base and metal electrode
Mounting: Direct-fit replacement for surface burner assembly
Operating Conditions: Designed for standard household gas ranges
Compliance: Built to OEM-equivalent standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the range and shut off the gas supply before starting repairs.
Steps:
Disconnect power and shut off gas supply.
Remove burner grates and top panel to access the igniter.
Detach the wire connector and mounting screw from the old igniter.
Install the new XPARTCO W10209656 igniter and reconnect wires.
Reassemble burner components, restore power and gas, and test ignition.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🛠️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Enjoy quick, reliable ignition every time — Add to Cart Now for a dependable, budget-friendly repair!
W10918546CM Gas Oven Igniter
Replaces Part Numbers: W10918546, W10140611, 98005652, W10918546VP, WPW10140611, AP6037202, PS11770066.
3.4 - 3.6 Amp,
1.5" block, 3.75" cage,
10" leads w/male pins.
Bake igniter for specific single burner Whirlpool range models.
Description: This Oven Igniter is a replacement part for select Maytag, Kenmore, Whirlpool gas oven models, responsible for igniting the gas burner that heats the oven. It works by drawing electrical current through the igniter filament, heating it to a high temperature until it glows and ignites the gas to start the cooking process.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO 5304509706 Gas Oven Igniter
Product Overview
The XPARTCO 5304509706 Gas Oven Igniter is designed to ignite the gas burner and ensure consistent oven heating performance. This Oven Igniter is a replacement part for select Frigidaire, Kenmore, GE gas oven models, designed to ignite the gas in the oven burner to start the heating process. This part is responsible for creating the spark that ignites the gas, providing the heat needed to cook and bake food. Over time, the oven igniter can wear out or become damaged, which can prevent the oven from heating.
Quick Answer
If your gas oven is not heating, takes too long to preheat, or the burner does not ignite, the 5304509706 igniter may be weak or faulty. Replacing this igniter restores proper ignition and consistent oven performance.
Replaces Part Numbers
Replaces OEM part number: 5304509706, 316489402, 316489408, 316119301, 4545981, 012505482182, EAP12071409, AFR18015, PD00035904, AP6230715, PS12071409, WB2X10016, WB02X10016, 1704, EAP241804, AGE826644, PD00042950, AH241804, EA241804, AP2009619, PS241804.
Compatibility
This gas oven igniter is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible gas ranges and ovens.
Frigidaire Gas Ranges
Electrolux Ovens
GE Gas Ranges
Kenmore Gas Ovens
Always verify your appliance model number before ordering.
Common Problems This Part Fixes
Oven not heating
Slow or delayed ignition
Burner not lighting
Gas smell due to ignition failure
Key Features
Designed for gas oven ignition
Provides fast and reliable burner ignition
High-quality aftermarket replacement
Durable construction for long-lasting performance
Product Specifications
Part Number: XP5304509706
Part Type: Gas Oven Igniter
Brand: XPARTCO
Condition: New
OEM / Aftermarket: Aftermarket
Application: Gas Ovens & Ranges
Troubleshooting Guide
Oven not igniting → Faulty igniter
Long preheat time → Weak igniter
No flame despite gas flow → Igniter failure
When Should You Replace This Igniter?
Replace this igniter if your oven fails to heat, takes too long to preheat, or does not ignite the gas burner properly.
Installation Notes
⚠️ Disconnect power and shut off gas before installation. Remove mounting screws, disconnect wiring, and install the new igniter carefully. Avoid touching the igniter surface with bare hands.
Related Parts
Gas Oven Safety Valve
Oven Temperature Sensor
Control Board
Frequently Asked Questions
Will this igniter fit my oven?This igniter fits many Frigidaire and compatible gas ovens. Always verify your model number.
What does an oven igniter do?It ignites the gas burner and allows the oven to heat properly.
What are signs of a bad igniter?Oven not heating, delayed ignition, or no flame during operation.
Is this OEM or aftermarket?This is a high-quality aftermarket replacement part.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Quality Tested Parts Compatibility Support
UNIVRND Oven Genuine GE Universal Round Igniter Kit
The UNIVRND is a genuine GE OEM universal round igniter kit for GE gas ranges and ovens. This is a high-temperature ignition component: when the burner is switched on, the igniter heats rapidly until it reaches the temperature needed to light the gas at the burner, allowing the flame to establish reliably each time the burner is used.
Round in shape, with an 8" lead, rated 2.5 to 3.0 amps at 120V, and CSA approved. Made in the USA and backed by a 1-year warranty. This is a complete kit — beyond the igniter itself, it includes mounting hardware, a mounting bracket, installation instructions, and 2 porcelain high-temperature wire nuts. This is a universal replacement designed to fit a broad range of GE gas range and oven models. Over time, the igniter's element weakens or fails from repeated heating and cooling cycles. Symptoms of a failing igniter include a burner that won't light, ignition that's slow or inconsistent, or clicking without ignition. It directly replaces WB2X9154 and UNIVRND.
Quick Answer
The UNIVRND Oven Genuine GE Universal Round Igniter Kit fixes GE gas ranges and ovens with a burner that won't light, ignition that's slow or inconsistent, or clicking without ignition. Round shape, 8" lead, 2.5-3.0A/120V, CSA approved, Made in USA. Includes mounting hardware, bracket, and 2 porcelain high-temp wire nuts. Replaces WB2X9154, UNIVRND. Even though this is sold as a universal part, GE's own guidance notes that size and shape can have small variations between models that otherwise look similar — verify your part number carefully before ordering.
Common Problems This Part Fixes
Gas burner won't light
Ignition that's slow or takes multiple attempts
Clicking sound without the burner actually igniting
Inconsistent or unreliable burner ignition
Igniter glowing but failing to light the burner
What's In The Kit
1x Universal Round Igniter, 8" lead
Mounting hardware and bracket
2x Porcelain, high-temperature wire nuts
Installation instructions
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
UNIVRND, EAP16728949, PS16728949, UNIVRND24PK, AGE1335580, AP7188082, PD00084791, WB2X9154, WB00X6640, 1990, 300259, 319887, 327617, 330689, 4336387, 4338008, AGE23042, AH243425, AP2014008, EAP243425, PD00001010, PS243425, Oven Round Igniter
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This is a universal igniter compatible with a broad range of GE gas ranges and ovens.
Note: Per GE's own guidance, please verify your part number is correct for your model before ordering — parts may look the same but the size and shape can have small variations between models. Always confirm your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — complete igniter kit for GE gas ranges and ovens
Resolves "won't light," "slow or inconsistent ignition," and "clicking without ignition" symptoms
High-temperature ignition element heats quickly to light the burner
Round shape, 8" lead
Rated 2.5 to 3.0 amps, 120V
CSA approved, Made in USA
Includes mounting hardware, bracket, installation instructions, and 2 porcelain high-temp wire nuts
Replaces UNIVRND, EAP16728949, PS16728949, UNIVRND24PK, AGE1335580, AP7188082, PD00084791, WB2X9154, WB00X6640, 1990, 300259, 319887, 327617, 330689, 4336387, 4338008, AGE23042, AH243425, AP2014008, EAP243425, PD00001010, PS243425, Oven Round Igniter
Compatible with a broad range of GE gas range and oven models
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
UNIVRND
Part Type
Universal Round Oven/Range Igniter Kit
Condition
Genuine OEM
Brand
GE
Shape
Round
Lead Length
8"
Electrical Rating
2.5 to 3.0 Amps, 120V
Certification
CSA Approved
Country of Origin
Made in USA
Kit Includes
Igniter, mounting hardware, bracket, 2 porcelain high-temp wire nuts, instructions
Application
Gas Ranges and Ovens
Repair Difficulty
Moderate — gas appliance component
Quantity
1 igniter kit
Compatible Brand
GE
Installation Notes
⚠️ Gas Appliance — Turn Off Gas Supply And Power Before Starting This is a gas ignition component. Before beginning any work, unplug the range or shut off power at the breaker, and shut off the gas supply to the appliance at the shutoff valve. If you smell gas at any point during this repair, stop immediately, do not operate any switches, leave the area, and contact your gas utility or a qualified technician from a safe location. Access to the igniter typically requires removing the oven bottom panel or reaching behind the range's rear panel, depending on your model — consult your appliance's service documentation for the exact access point. Disconnect the wiring connector from the old igniter and remove the mounting screws securing it in place. Install the new UNIVRND using the included mounting bracket and hardware, securing it in the same position, and connect the wiring using the included porcelain high-temperature wire nuts rather than standard wire nuts, since ordinary ones aren't rated for the heat in this area. Restore the gas supply and power. Test the burner according to your appliance's normal operation, and confirm the igniter glows and the burner lights reliably. If you are not fully comfortable working with gas line connections, have a qualified technician perform this repair instead.
⚠️ WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and reproductive harm. For more information, visit P65Warnings.ca.gov.
Frequently Asked Questions
Does this include everything I need to install it, or just the igniter itself?
This is a complete kit — it includes the igniter, mounting hardware, a mounting bracket, installation instructions, and 2 porcelain, high-temperature wire nuts. Use the included porcelain wire nuts rather than standard ones when making the wiring connection, since this area gets hot enough that ordinary wire nuts aren't rated for it.
My burner won't light. Is this the part I need?
Yes, this is the most direct symptom of a failed igniter. Since this component is what heats up to light the gas at the burner, a weakened or failed igniter element can prevent the burner from lighting at all, or cause slow, inconsistent ignition.
If this is a "universal" part, do I still need to check compatibility?
Yes. Even though this igniter is designed to fit a broad range of GE gas range and oven models, GE's own guidance specifically notes that similar-looking igniters can have small variations in size and shape between models. Confirm your part number and model before ordering to avoid a mismatch.
Is this safe to install myself?
This involves working near a gas appliance's ignition system, so extra care is warranted. Always shut off the gas supply and power before starting, and if you're not comfortable working with gas connections or you smell gas at any point, stop and have a qualified technician complete the repair instead.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original ignition element design, lead length, and mounting configuration of the igniter it's designed to replace.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
