(4 Pack) XPATC5 Furnace & Air Conditioner Control Circuit Board 5 Amp Fuse – Universal HVAC Replacement
Product Description
Protect your HVAC system’s control board with the XPATC5 Furnace & Air Conditioner Control Circuit Board 5 Amp Fuse (4 Pack). These high-quality aftermarket blade fuses are designed to safeguard furnace and air conditioner control boards from electrical overloads and short circuits. A blown 5-amp fuse can cause the HVAC system to stop working entirely. Replacing it with reliable XPATC5 fuses helps restore operation while protecting sensitive electronic components.
XPATC5 fuses are commonly used in residential HVAC systems and are ideal to keep on hand for quick repairs.
Replaces Part Numbers
ATC-5, ATO-5, 5 Amp HVAC Control Fuse, Furnace Control Board Fuse, Air Conditioner 5A Fuse
Compatibility
This 5 amp HVAC control board fuse is compatible with many furnace and air conditioner systems from manufacturers including Carrier, Trane, Lennox, Goodman, Rheem, York, and others that use standard ATC/ATO 5-amp blade fuses.
Always verify fuse amperage and type before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Built to OEM-equivalent electrical specifications
⚡ 5 Amp Rating – Protects HVAC control boards from overloads
🧯 Critical Safety Component – Helps prevent damage to circuit boards
📦 Convenient 4-Pack – Keep spares on hand for future service
💰 Cost-Effective Solution – Affordable alternative to OEM HVAC fuses
📐 Product Specification
Part Number: XPATC5
Component Type: HVAC Control Board Fuse
Amperage Rating: 5 Amp
Voltage Rating: 32V
Fuse Style: ATC / ATO Blade Fuse
Quantity: 4-Pack
Application: Furnace & air conditioner control boards
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Needle-nose pliers or fuse puller
⚠️ Safety First: Always turn off power to the HVAC system before replacing fuses to avoid electrical shock or equipment damage.
Basic Steps:
Shut off power to the furnace or air conditioner.
Open the control board access panel.
Locate the blown 5-amp fuse.
Remove and replace it with a new XPATC5 fuse.
Restore power and test system operation.
⏱️ Time Required: 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket HVAC Parts
🔄 30-Day Return Policy
Protect your HVAC system and keep it running — Add to Cart Now for a reliable, budget-friendly solution!
XPARTCO 62-23543-01 Gas Furnace Flame Sensor – Compatible with Rheem, Ruud, and WeatherKing Furnaces
Product Description
Restore safe and reliable furnace operation with the XPARTCO 62-23543-01 Gas Furnace Flame Sensor. This high-quality aftermarket replacement detects the presence of a burner flame and signals the control board to keep the gas valve open. A dirty or failed flame sensor can cause short cycling, ignition failure, or a furnace that won’t stay lit. Replacing it with this durable XPARTCO sensor ensures proper flame detection and dependable heating performance.
Specification :
The furnace flame sensor is designed to detect the flame.
1/4”male quick connect, Angle - sensor offset: 90 degree.
Replaces Part Numbers
62-23543-01,62-23543-02, 62-23543-03, 62-23543-04
Compatibility
This replacement flame sensor fits select Rheem, Ruud, and WeatherKing gas furnaces.
Example compatible models include (but are not limited to):Rheem RGRJ series, Ruud UGDG series, WeatherKing RGRA series.
Always verify your furnace’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to match OEM flame-sensing performance
🔥 Accurate Flame Detection – Ensures gas valve remains open only when flame is present
💰 Cost-Effective Repair – Reliable alternative to expensive OEM sensors
🛠️ Simple Installation – Direct-fit design with single mounting screw
🛡️ Fixes Common Issues – Solves furnace short cycling, ignition failure, or burner shutdown
📐 Product Specification
Part Number: 62-23543-01
Component Type: Gas Furnace Flame Sensor
Material: Stainless steel sensor rod with ceramic insulator
Mounting: Single-screw bracket mount
Electrical Connection: Spade terminal
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, fine abrasive pad (optional for cleaning)
⚠️ Safety First: Turn off power and gas supply to the furnace before servicing.
Steps:
Shut off furnace power and gas supply.
Locate the flame sensor near the burner assembly.
Disconnect the wire and remove the mounting screw.
Install the new XPARTCO 62-23543-01 flame sensor.
Reconnect the wire, restore power and gas, and test furnace operation.
⏱️ Time Required: 5–10 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance & HVAC Parts Supplier
🔄 30-Day Return Policy
Restore safe furnace ignition and heating — Add to Cart Now for a reliable, budget-friendly replacement!
WP98014893 Oven Genuine Gas Safety Valve
Description: The Gas Safety Valve is an OEM replacement part for Whirlpool gas ranges. This important safety device works to automatically shut off the gas supply to the range if abnormal flame conditions, such as flame rollout, occur.
Replaces Part Numbers:WP98014893, W11399433, 98014893, 1061522, 98007439, AP6014264, PS11747502.
California Residents only
WARNING: California’s Proposition 65
1408 Gas Furnace Hot Surface Igniter
The 1408 is a replacement 120V silicon carbide hot surface igniter for gas furnaces. When the furnace calls for heat, the igniter glows white hot and lights the gas burners. Over time the element can crack or wear out, and a failed igniter is a common reason a gas furnace tries to start but never lights or never heats.
This igniter replaces the Robertshaw 41-408 and the Rheem 62-22868-93. It is a furnace igniter, not an oven igniter, so check the part number and the look of your old igniter before ordering.
Quick Answer
The 1408 Gas Furnace Igniter replaces a cracked, burned-out, or failed hot surface igniter on a gas furnace that tries to start but won't light. Replaces 41-408 and 62-22868-93. Classic symptom: the inducer runs, but the igniter never glows and the burners never light.
Common Problems This Part Fixes
Furnace won't light, with no heat
Igniter does not glow when the furnace calls for heat
Cracked, broken, or visibly damaged igniter element
Furnace cycles through ignition attempts and then locks out
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This igniter directly replaces the following part numbers:
1408, 41-408, 62-22868-93, 62-22868-02, 62-22868-82, 62-22441-01, 62-22868-92, B340039P01, 767A-372, 271N, IG408, 41-408, 67900, IG1408
The first three numbers are the main references for this igniter. The others appear on retailer cross-reference lists. Confirm against your furnace's parts list, or contact our support team, if your furnace calls out a different number.
Compatibility
This igniter is a replacement for the Robertshaw 41-408 and the Rheem 62-22868-93, and it is used on gas furnaces that call for either one. The Rheem number is used on Rheem, Ruud, WeatherKing, and Protech furnaces, including these series examples:
Rheem/Ruud UGDG, UGLG, UGLH, UGPH, UGTA, UGVG
Rheem/Ruud 80LJ, 80PJ, 90RJ, 90TJ
Note: The series above are a sample, not a full list. Retailers do not list the lead length or connector style for this igniter, so compare your old igniter's shape, lead, and connector to the new one, and contact our support team with your furnace model number to verify fit before ordering.
Key Features
120V silicon carbide hot surface igniter for gas furnaces
Replaces Robertshaw 41-408 and Rheem 62-22868-93
Resolves no-light and no-heat problems caused by a failed igniter
Furnace igniter, not for gas ovens
Product Specifications
Part Number
1408
OEM Part Number
62-22868-93, 41-408
Part Type
Gas Furnace Hot Surface Igniter
Condition
Aftermarket Replacement
Element Material
Silicon Carbide
Voltage
120V
Application
Gas Furnaces
Installation Notes
⚠️ Turn Off Power and Gas Before Installing Switch off power to the furnace at the breaker and the furnace switch, and shut off the gas supply, before beginning. Wear work gloves. Let the old igniter cool, disconnect its lead, remove it, and fit the new igniter in the same position. Handle the new igniter only by its ceramic base, and avoid touching the silicon element, since skin oils can cause early failure. If the furnace still does not light, check the control board and the gas valve.
Frequently Asked Questions
My furnace won't light. Is this the part I need?
A cracked or burned-out igniter is a common cause. If the igniter doesn't glow when the furnace calls for heat, or the element is visibly cracked, it is likely the problem. If the igniter glows but the burners don't light, check the gas valve and control.
Does this replace the Robertshaw 41-408 and the Rheem 62-22868-93?
Yes, it is listed as a replacement for both. Because retailers do not list lead length or connector style, compare your old igniter to this one, or contact our support team, before ordering.
Why shouldn't I touch the igniter element?
Skin oils on the silicon element can cause the igniter to fail early. Handle it by the ceramic base only.
Will this fit my furnace?
It is used on gas furnaces that call for a 41-408 or 62-22868-93 igniter, but the series list above is only a sample. Check your furnace's parts list, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 0130F00010 Gas Furnace Flame Sensor
Fits the Specific Goodman Gas Furnace models
Replaces Part Numbers:TJFLS013, AP6326767, 0130F00010
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO H150 Furnace Silicon Nitride Rod Ignitor
The H150 universal gas furnace igniter come with a 1.95-inch ceramic nitride heating element, a 1.25-inch ceramic insulator, a 304 stainless steel bracket, and a 15.5-inch high temperature resistant wire(20 AWG). Voltage: 120V±10%-15%, 50/60HZ. Power Rating: 150W. Cold resistance: 9-17Ω. At 120V furnace igniter H150 can reach 1200 degrees in a short time
The H150 universal furnace igniter replacement can be used in a wide range of machines and is the perfect replacement for silicon carbide ignitors in water heater boilers and gas forced-air furnaces, replacing more than 180 types of ignitors and covering nearly 90% of all applications. Such as stoves, furnace, warm air motion, gas ignition, hot surface igniter, infrared light source, pool heater, boiler, etc
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WPW10545291 Genuine OEM Whirlpool Range / Oven Thermal Fuse
The WPW10545291 is a genuine Whirlpool OEM thermal fuse mounted next to the heating source inside wall ovens, ranges, and microwave-oven combo units. This fuse is a one-time safety device: as long as the oven stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — most often during a self-clean cycle, which runs far hotter than normal baking or roasting — the fuse permanently opens the circuit and cuts power. That's why a blown thermal fuse produces such a distinctive symptom: the oven loses power completely, sometimes with the door still electronically locked from the self-clean cycle that triggered the failure.
Unlike a thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. Because it's mounted directly behind the control panel on many wall oven models, replacing it typically means pulling the unit partway out from the wall and removing the control section to reach it, rather than a simple rear-panel swap. It directly replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, and W10436435.
Quick Answer
The WPW10545291 Genuine OEM Whirlpool Range / Oven Thermal Fuse fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall ovens, ranges, and microwave-oven combos that lost power completely — often right after a self-clean cycle. Replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, W10436435. If the door is electronically locked and won't open, you may need to manually release the lock before you can access the oven for this repair — see the FAQ below.
Common Problems This Part Fixes
Oven has no power at all — no lights, no display, no response to any button
Oven lost power suddenly, especially during or right after a self-clean cycle
Oven door remains electronically locked with no power to release it
Oven that stopped working after running unusually hot
Control panel completely dark and unresponsive
Continuity test shows an open circuit across the old fuse
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range/oven thermal fuse directly replaces the following OEM and cross-reference part numbers:
WPW10545291, W10545291, 3021646, W10436435, AP6022803, AWP50815, EAP11756140, PD00032820, PS11756140.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermal fuse is compatible with select Whirlpool wall ovens, ranges, and microwave-oven combo units, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances built on the Whirlpool platform, including model numbers such as WOD77EC7HS, WOD77EC0HV, and WOD51EC7AB02.
Note: Whirlpool uses several different thermal fuses across its range/oven lineup, including separate fuse designs used in other model families. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration
One-time safety device that cuts power if the oven overheats
Resolves "no power at all," "lost power after self-clean," and "door locked with no power" symptoms caused by a blown fuse
Mounts next to the heating source, typically behind the control panel
Replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, and W10436435
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall ovens, ranges, and microwave-oven combos
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WPW10545291
Part Type
Range / Wall Oven Thermal Fuse
Condition
Genuine OEM
Brand
Whirlpool
Application
Wall Ovens, Ranges, Microwave-Oven Combo Units
Location
Next to the heating source, typically behind the control panel
Resettable
No — one-time use, must be replaced once blown
Repair Difficulty
Moderate to Hard — control panel disassembly required on many models
Quantity
1 thermal fuse
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Unplug Oven Or Shut Off Breaker Before Starting — Access Is Typically Behind The Control Panel Shut off the oven's power at the breaker before beginning. Wear work gloves. If the door is electronically locked and won't open due to the power loss, you may need to manually release it first — see the FAQ below for a common workaround. Remove the oven's retaining screws and carefully pull the unit out from the wall a few inches to access the screws holding the control section in place. Remove the screws securing the control panel — typically four — and pull the control unit loose, letting the display ribbon cable stay connected while you rest the panel out of the way on top of the oven; avoid pulling it further than the ribbon allows. The thermal fuse is usually mounted right behind the control panel at this point. Photograph the wiring before disconnecting the old fuse's connectors. Pull the connectors off the old fuse and plug them onto the new WPW10545291 fuse in the same orientation. Reconnect the control panel's ground wire and ribbon cable, reinstall the control panel and its screws, and carefully push the oven back into the wall opening, securing it with its retaining screws. Restore power at the breaker and confirm the oven powers on normally and the door unlocks and operates correctly. Tools needed: Phillips screwdriver, power tester (helpful), work gloves.
Frequently Asked Questions
My oven lost all power right after a self-clean cycle. Is this the thermal fuse?
Yes, this is one of the most common and well-documented triggers for this exact failure. Self-clean cycles run at extremely high temperatures compared to normal cooking, and if that heat exceeds what the thermal fuse is rated to tolerate, it blows to protect the oven — cutting all power in the process. A total loss of power during or shortly after a self-clean cycle is a strong sign this fuse is the cause.
My oven door is locked and I have no power to release it. How do I get it open?
This is a known complication when the thermal fuse blows during or after a self-clean cycle, since the door lock can remain engaged with no power available to release it electronically. One documented workaround: with the house power to the oven confirmed off, some owners have used a thin, flexible material (such as a bent paper clip or a flexible cutting board edge) worked carefully between the door and the lock mechanism to manually trip the lock open. This varies by model and takes patience — if you're not comfortable attempting it, a qualified appliance technician can open the door safely.
Can I just reset the thermal fuse instead of replacing it?
No. Unlike a thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your oven, range, or microwave-oven combo.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers
Product Description
Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C).
A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components.
XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance.
Replaces Part Numbers
3977393, AP3094244, PS334299, EAP334299
Compatibility
This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers.
Commonly installed on the heater housing assembly.
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM temperature rating and fit
🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection
🛡️ Prevents Overheating Damage – Protects heating element and dryer components
🧩 Direct-Fit Design – Installs easily without modification
💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs
📐 Product Specification
Part Number: 3977393
Component Type: Dryer Thermal Cut Off
Temperature Rating: 309°F (154°C)
Function: One-time over-temperature safety cutoff
Mounting: Screw-mounted
Application: Dryer heater housing assembly
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock.
Basic Steps:
Disconnect dryer power.
Remove rear panel to access heater housing.
Locate and disconnect the old thermal cut off.
Remove mounting screws and install the new XPARTCO 3977393 cut off.
Reconnect wiring and reassemble the dryer.
Restore power and test operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!
W11047722 Genuine OEM Range Radiant Surface Element - Compatible with Whirlpool, KitchenAid, Maytag
Product Description
Restore your range’s cooking performance with the W11047722 Genuine OEM Range Radiant Surface Element. This Whirlpool-manufactured element is designed for select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and other compatible ranges. It provides even heat distribution for reliable cooking, addressing issues like uneven heating, no heat, or burnt-out elements. This single element is rated at 2500W and 240V, ensuring efficient operation for large to medium cookware.
Note: Includes (1) radiant surface element. Disconnect power before installation. Verify compatibility with your range model.
Replaces part numbers: W11047722, WP8273992, W10248262, 8273992, AP6041999, PS11775308, 316135401, 316224200, 316224201, 318198835, PD00044547, EAP11775308, FIX11775308, AH2361362, EA2361362, AP4416812, PS2361362.
Compatibility:
Compatible with select range models, including but not limited to:
Whirlpool: WFE525S0HV0, WFE525S0HZ0, WFE525S0JB0, WFE525S0JS0, WFE525S0JW0
KitchenAid: KSEG700EBS0, KSEG700ESS0, KSEG700EWH0
Maytag: MER6600FB0, MER6600FW0, MER6600FZ0
Jenn-Air: JEC3430BB00, JEC3430BS00
Amana: AER6603SFB0, AER6603SFS0, AER6603SFW0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana ranges.
🔧 Specifications: 2500W, 240V, 9 3/4-inch radiant element, glass-ceramic construction.
💪 Reliable Performance: Delivers consistent heat for efficient cooking.
🛠️ Easy Installation: Requires screwdriver and gloves; typically installed in 15–30 minutes.
🛡️ Effective Fixes: Resolves uneven heating, no heat, or burnt-out element issues.
Product Specification
Part Number: W11047722
Component Type: Radiant surface element
Material: Glass-ceramic with metal heating coil
Dimensions: Approximately 9 3/4" diameter
Electrical Specs: 2500W, 240V
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the range from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your range cooking efficiently today!
Add to cart now for a reliable fix!
