Search results for "Oven Racks"

WP74010750 Genuine OEM Whirlpool Oven Bake Element The WP74010750 is a Genuine OEM Whirlpool replacement oven bake element compatible with select Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges and ovens — particularly CE-series, JDS-series, and MES-series slide-in and freestanding ranges. The bake element is the lower heating element located at the bottom of the oven cavity. It provides the primary heat source for baking, roasting, and preheating. When the element coil burns through, the oven will not heat, will bake unevenly, or will trip the circuit breaker when the bake cycle is selected. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 2585W with push-on terminal ends (two 1/4" high-temp connectors). It measures approximately 23-5/8" wide x 15-3/8" long with 3-3/8" inserts. It directly replaces 74010750, 74003039, 7406P425-60, 1184162, WP74010750VP, ERB0750, AP6011209, PS11744404, and several additional cross-reference numbers. Installs in 15–20 minutes with basic hand tools. Quick Answer The WP74010750 Genuine OEM Whirlpool Oven Bake Element fixes electric ovens that won't heat, bake unevenly, or trip the circuit breaker during bake. 2585W, push-on terminal ends (two 1/4" high-temp connectors), 23-5/8"W x 15-3/8"L, 3-3/8" inserts. Genuine OEM. Compatible with Whirlpool CE, Jenn-Air JDS, Maytag MES series and related brands. Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, AP6011209, PS11744404. Common Problems This Part Fixes Oven produces no heat — bake element coil has burned through Oven takes much longer than normal to preheat Food baking unevenly — bottom of food undercooked while top is done Bake element not glowing red during the bake cycle Visible burn marks, blistering, holes, or breaks in the element coil Oven trips the circuit breaker when the bake cycle is selected — shorted element Burning smell during a bake cycle — arcing at a weak point in the element Replaces Part Numbers This bake element directly replaces the following OEM and cross-reference part numbers: WP74010750, 74010750, 1184162, 74003039, 7406P425-60, AP6011209, AWP47950, EAP11744404, PD00002565, PS11744404, WP74010750VP. Contact our support team with your model number if you need confirmation before ordering. Compatibility This bake element is compatible with select electric ranges and ovens from the following brands and series: Whirlpool electric ranges — CE35200, CE38800 and related CE-series models Jenn-Air electric ranges — JDS8850, JDS9860 and related JDS-series slide-in models Maytag electric ranges — MES5770 and related MES-series models KitchenAid electric ranges (select models) Amana electric ranges (select models) Kenmore / Sears electric ranges (select Whirlpool-built models) Magic Chef electric ranges (select models) Admiral electric ranges Norge electric ranges Roper electric ranges Note: Always verify your exact model number before ordering — bake elements are model-specific due to differences in dimensions and terminal configuration. The WP74010750 uses 1/4" push-on terminals and specific mounting dimensions that differ from other Whirlpool-family bake elements. If you are not sure this element is the right fit, contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for baking, roasting, and preheating in compatible electric ovens Rated 2585W — correct wattage for compatible CE, JDS, and MES series models Push-on terminal ends — two 1/4" high-temperature connectors for direct wire attachment Dimensions: approximately 23-5/8" wide x 15-3/8" long, with 3-3/8" inserts Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, and AP6011209 Compatible with Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number WP74010750 Part Type Oven Bake Element (Lower Heating Element) Condition Genuine OEM Application Electric Ranges and Ovens Wattage 2585W Terminal Type Push-on — two 1/4" high-temperature connectors Width Approximately 23-5/8 inches Length Approximately 15-3/8 inches Inserts 3-3/8 inches Compatible Brands Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Range or Turn Off Breaker Before Starting Disconnect power before beginning and allow the oven to cool completely. Open the oven door and remove all racks. The bake element is located at the bottom of the oven cavity. Remove the screws securing the element bracket to the rear oven wall — typically one or two Phillips screws at the back. Carefully pull the element forward toward the door to expose the two 1/4" push-on wire connectors behind the oven rear wall. Note the position of each wire before disconnecting — take a photo. Pull each wire connector off the element terminals by gripping the connector (not the wire) and pulling straight back. Connect the two wires to the new WP74010750 element's terminals, slide the element back into position, and secure the mounting screws. Restore power and run a bake cycle to confirm the element heats and glows red. Tools needed: Phillips screwdriver. Frequently Asked Questions How do I know if my bake element has failed? The clearest sign is an oven that does not heat, takes much longer than usual to preheat, or bakes food unevenly with the bottom undercooked. When the bake element is working, it should glow bright red during a bake cycle. If it does not glow at all, the element has failed. You can also visually inspect the element for burn marks, blistering, cracks, or a visible break in the coil. A multimeter continuity test will confirm failure — a working element shows continuity (resistance of approximately 10–100 ohms), while a failed element reads open circuit. If the element trips the circuit breaker when selected, the element coil has shorted to the metal housing — replace it immediately. What is the difference between WP74010750 and WP74003019? Both are Genuine OEM Whirlpool oven bake elements but for different model families and with different wattage ratings. The WP74010750 is rated 2585W and is used on CE, JDS, and MES-series electric ranges. The WP74003019 is rated 2800W and is used on a different set of models. They are not interchangeable — always verify your model number to confirm which element is correct for your oven before ordering. Is it normal for a bake element to arc or spark before it fully fails? Yes — it is not unusual for a bake element to arc or spark at a weak spot before the coil fully burns through. If you see sparking, arcing, or a bright flash from the element area, immediately turn off the oven and disconnect power. Do not use the oven again until the element has been replaced. An arcing element can damage the oven liner and, in rare cases, pose a fire risk. The good news is that once you replace the WP74010750 element, the oven should perform normally again. Are the wires interchangeable on the bake element terminals? On most electric range bake elements — including the WP74010750 — the two terminal wires are interchangeable. The bake element is a resistance heater with no polarity, so either wire can connect to either terminal and the element will heat correctly. However, it is good practice to photograph the original connection before disconnecting to ensure you reconnect in the same configuration, particularly if one wire is color-coded differently from the other. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same bake element installed in compatible Whirlpool, Jenn-Air, Maytag, and related brand electric ranges from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB13K21 Gas Oven Flat Igniter with Harness The XPARTCO WB13K21 is an aftermarket replacement flat-style gas oven igniter with harness compatible with select GE, Hotpoint, RCA, and Kenmore gas ranges and ovens. The oven igniter is a silicon carbide heating element mounted inside the oven next to the burner. It serves a dual purpose: it draws electrical current through the oven safety valve to hold it open, and it heats to ignition temperature to light the gas burner. The igniter must draw sufficient current — typically 3.2–3.6 amps — to hold the safety valve fully open. A weakened igniter that draws too little current will glow but never fully open the gas valve, preventing the burner from lighting. This flat-style igniter draws 3.4–3.6 amps at 115V. The ceramic block measures 1-1/2" L, with an overall bracket/cage measuring 3-3/4"L x 2-1/8"W x 13/16"H. The harness and plug extend approximately 7-7/8" from the igniter body with female pin connectors and a double wing mounting bracket. It can be used as a bake or broil igniter replacement on compatible models. It directly replaces WB13K21, WB13K12, WB13K13, WB13K14, WB13K0012, WB13K0013, WB13K0014, WB13K0021, WB13K10009, WB13K10026, IG21, 2494, AP2020569, AH231280, EA231280, EAP231280, PS231280, and PD00001023. Note: if the connector does not match your range's harness, cut the connector and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO WB13K21 Gas Oven Flat Igniter with Harness fixes GE, Hotpoint, RCA, and Kenmore gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat igniter, 3.4–3.6A, 115V. 1-1/2" ceramic block, 3-3/4"L x 2-1/8"W x 13/16"H bracket. 7-7/8" harness with female pins. If connector doesn't match, splice with porcelain wire nuts. Replaces WB13K21, WB13K12, WB13K13, WB13K14, IG21, AP2020569, AH231280, PS231280. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange but the gas burner never lights Oven takes more than 90 seconds to ignite after turning on Oven preheats very slowly — weak igniter no longer drawing enough current to fully open the gas valve Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: WB13K21, WB13K0012, WB13K0013, WB13K0014, WB13K10009, WB13K10026, WB13K12, WB13K13, WB13K14, 2494, AH231280, AP2020569, AGE21391, EA231280, EAP231280, PD00001023, PS231280. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands: GE gas ranges and ovens (select models) Hotpoint gas ranges and ovens (select models) RCA gas ranges and ovens (select models) Kenmore / Sears gas ranges (select GE-built models) Note: Can be used for both bake and broil igniter replacement on compatible models. If the two-pin connector does not match your range's existing harness connector, cut the connector off the new igniter and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner due to heat. Always verify your model number before ordering. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the safety valve to open it and allow gas to flow to the burner Draws 3.4–3.6 amps at 115V — correct amperage range to reliably open the GE oven gas safety valve Ceramic block: 1-1/2" L; bracket/cage: 3-3/4"L x 2-1/8"W x 13/16"H Harness and plug extend approximately 7-7/8" from the igniter body Female pin connectors with double wing mounting bracket — quick install on compatible models Can replace bake or broil igniter on compatible models If connector does not match: cut and splice using porcelain wire nuts (included) — never use standard plastic wire nuts near the burner Replaces over 18 older GE oven igniter cross-reference part numbers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPWB13K21 Part Type Gas Oven Flat Igniter with Harness (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (bake and broil) Igniter Style Flat (cageless silicon carbide element) Amperage Draw 3.4 – 3.6 Amps Voltage 115V AC Ceramic Block Length 1-1/2 inches Bracket / Cage Dimensions 3-3/4"L x 2-1/8"W x 13/16"H Harness / Lead Length Approximately 7-7/8 inches from igniter body Connector Type Female pins, two-pin quick-disconnect (splice with porcelain nuts if needed) Mounting Double wing bracket Material Silicon carbide / Ceramic / Metal / Plastic Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are secure. If you are not comfortable working on gas appliances, have this part installed by a qualified technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to skin oils. Do not touch the igniter element with bare hands — oils from skin will create hot spots that prematurely burn the igniter. Handle only by the bracket, harness, and mounting wings. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector at the connection point inside the oven. Remove the two screws securing the mounting bracket. If the new igniter's connector matches the harness, plug it in directly. If it does not match, cut the connector from the new igniter and use the included porcelain wire nuts to splice the wires to your range's existing harness — do not use plastic wire nuts. Mount the new igniter using the double wing bracket and two screws. Reinstall the oven bottom panel, restore gas and power, and run a bake cycle to confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, socket set, work gloves. Frequently Asked Questions My igniter glows but the burner never lights — is it the igniter? Yes, almost certainly. A gas oven igniter that glows orange or red but does not light the burner is a classic sign of a weakened igniter. The igniter must draw enough electrical current — typically 3.2 amps or more — to hold the gas safety valve fully open. As the silicon carbide element ages, its resistance increases and it draws progressively less current. When the current drops below the threshold needed to hold the valve open, the valve never fully opens, even though the igniter appears to glow. If the igniter glows for more than 90 seconds without lighting the burner, it needs to be replaced. Why can't I use plastic wire nuts to splice the igniter wires? The igniter is located inside the oven cavity, directly adjacent to the gas burner, where temperatures during operation can easily exceed what standard plastic wire nuts are rated for. Plastic wire nuts can melt or deform at oven operating temperatures, potentially exposing bare wire connections and creating a short circuit or fire hazard. Porcelain wire nuts are specifically rated for high-temperature applications and are the only safe connector to use when splicing igniter wires near the oven burner. Always use porcelain — never plastic — for any wiring connection inside the oven cavity. Can this igniter be used for both bake and broil? Yes — on compatible GE, Hotpoint, and Kenmore models, the WB13K21 can be used to replace both the bake igniter (lower burner) and the broil igniter (upper burner), as both igniters use the same part number and specifications on these models. Verify your range's parts diagram to confirm that both igniters use the WB13K21 before ordering for the broil position. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, it has weakened. You can also use a multimeter — disconnect the igniter wires and measure resistance. A working WB13K21-style igniter typically reads between 40 and 90 ohms at room temperature (a lower resistance draws more current; a very high resistance means the element is nearly failed). An open circuit (infinite resistance) means the element has burned through completely. If the igniter does not glow at all when the oven is turned on, it has completely failed electrically. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original WB13K21 oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304535768 Dishwasher Genuine Lower Dish Rack Genuine lower dishwasher rack designed to hold dishes securely and restore smooth loading, unloading, and wash performance. ✓ Genuine Dishwasher Part ✓ Part 5304535768 ✓ Compatibility Support Product Description The 5304535768 Dishwasher Genuine Lower Dish Rack is designed for the lower section of compatible dishwashers. It helps hold plates, bowls, cookware, and other dishwasher-safe items in the correct position during the wash cycle. Replacing a damaged, rusted, or worn lower rack can improve loading convenience, protect dishes, and help restore proper dishwasher performance. Quick Answer If your dishwasher lower rack is rusted, damaged, missing tines, difficult to slide, or no longer holds dishes properly, the 5304535768 lower dish rack may need replacement. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Rusted or damaged lower dish rack Broken or missing rack tines Dishes not staying securely in place Lower rack difficult to load or unload Worn rack coating or exposed metal Replaces part Number 5304535768, 808602303, 5304535252, 808602302, 154866702, 154207803, 154207804, 154207905, 154207906, 154207907, 154224902, 154308304, 154308305, 154308306, 154319604, 154319706, 154319708, 154320901, 154320902, 154320903, 154320904, 154320905, 154320906, 154321001, 154321002, 154425502, 154432601, 154432602, 154432603, 5304534201, AFR20116, AP7218623, FIX17219739, PD00084201, PS17219739. Compatibility This genuine lower dish rack fits select Frigidaire, Electrolux, Kenmore, and compatible dishwasher models using part number 5304535768. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Genuine lower dishwasher rack replacement Helps organize and secure dishes during wash cycles Restores smooth loading and unloading Designed for compatible dishwasher models Durable rack construction for everyday use Product Specifications Brand Genuine Frigidaire OEM Part Type Dishwasher Lower Dish Rack Primary Part Number 5304535768 Replaces Part Number 5304535768 Compatible Appliance Type Dishwasher Condition New Installation Remove the old lower rack and slide the replacement rack into the lower dishwasher track area. Verify smooth movement before use. Troubleshooting Guide Inspect the old rack for rust, broken tines, or damaged coating. Check that the rack wheels or rollers move smoothly if included or reused. Confirm the replacement rack slides properly in the dishwasher tub. Do not force the rack if it does not align correctly. Verify model compatibility before installation. When Should You Replace This Part? Replace the lower dish rack if it is rusted, bent, broken, difficult to slide, missing tines, or no longer holds dishes securely during wash cycles. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts and genuine appliance components. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Genuine Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DE92-02588G Genuine OEM Samsung Range Control Board The DE92-02588G is a genuine Samsung OEM main control board and clock assembly for Samsung gas ranges. This board is the range's central processor for the oven side of the appliance — it monitors oven temperature, drives the heating functions, and includes the digital display that shows the time and temperature settings. Every button press on the control panel is interpreted here, and every heating command the oven executes is issued from this board. Samsung's own service guidance draws a clear line for when this board is the correct part: order it when the range display is completely blank or unresponsive, or when the clock/timer still works but none of the oven's heating functions operate. It is specifically the wrong part when only certain buttons fail to respond or specific functions are missing while the rest of the panel works normally — that pattern points to a failed switch membrane (touchpad) instead, a separate component. Power surges, including lightning strikes near the home's electrical service, are a documented real-world cause of this board failing outright. It directly replaces AP5800586, 3553835, and PS8764724. Quick Answer The DE92-02588G Genuine OEM Samsung Range Control Board fixes Samsung gas ranges with a completely blank or unresponsive display, or a range where the clock/timer works but none of the oven's heating functions operate. Includes the digital clock/display. Replaces AP5800586, 3553835, PS8764724. Do NOT order this board if only certain buttons don't respond or specific functions are missing while everything else works — that points to a failed switch membrane (touchpad), not this board. Common Problems This Part Fixes Range display is completely blank or dead Control panel is entirely unresponsive to any button press Clock and timer function normally, but no oven heating functions work at all Oven won't heat despite the range otherwise appearing to have power SE or similar error code displayed on the control panel Range that stopped working suddenly after a power surge or nearby lightning strike Digital display showing incorrect or scrambled time/temperature readings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range control board directly replaces the following OEM and cross-reference part numbers: DE92-02588G, AP5800586, 3553835, EAP8764724, ASM553766, PD00025599, PS8764724 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control board is compatible with select Samsung gas ranges, including model numbers such as: NX58F5300SS, NX58F5300SW NX58F5500SS, NX58F5500SW, NX58F5500SB NX58R4311SS, NX58R4311SG Note: Before ordering, confirm your symptom matches this board specifically. If the display is blank/dead, or the clock works but heating functions don't, this board is correct. If only some buttons or functions fail while others work fine, the issue is very likely the switch membrane (touchpad) instead — a separate part from this control board. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Samsung OEM part — factory-specified processor, relay, and display circuitry Monitors oven temperature and drives all oven heating functions Includes the digital clock/display for time and temperature readouts Resolves "blank display," "unresponsive control panel," and "no heating functions" symptoms caused by control board failure Direct drop-in replacement for the original board mounting and harness connectors Replaces AP5800586, 3553835, and PS8764724 Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward repair — typically 15 to 45 minutes with basic tools Product Specifications Part Number DE92-02588G Part Type Range Oven Main Control Board & Clock Condition Genuine OEM Brand Samsung Application Gas Ranges Function Monitors oven temperature, drives heating functions, digital clock/display Repair Difficulty Easy to Moderate — 15 to 45 minutes Quantity 1 control board Compatible Brand Samsung Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting — Handle The Board By Its Edges Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards, and allow the range to cool if recently used. Wear work gloves. Access is typically through the rear of the control panel: remove the screws securing the back cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and getting one out of place will cause a no-start or miswired symptom. Handle the new board by its edges rather than touching the components directly, and avoid working on a carpeted surface or in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Install the new DE92-02588G in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Reinstall the rear cover, restore power, and test the display, clock, and all oven functions to confirm normal operation. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Some of my buttons don't respond but others work fine. Do I need this board? Probably not. Samsung's own guidance is specific here: if certain buttons don't respond, specific functions are missing, or you can't adjust particular settings while the rest of the panel works normally, that pattern points to a failed switch membrane (touchpad) rather than this main control board. This board is the correct part when the display is completely blank/dead, or when the clock and timer work but no heating functions operate at all. My range stopped working right after a thunderstorm. Could that be related? Yes, this is a documented real-world cause of this exact board failing. Power surges, including those from a nearby lightning strike, can damage the control board's circuitry outright, leading to a sudden and complete loss of function. If your range died abruptly during or shortly after a storm, this board is a strong candidate for the cause. Should I replace the switch membrane at the same time, just in case? Some people do replace both together, especially if they want to be certain the repair is complete on the first attempt rather than risk needing a second repair shortly after. But if your symptoms clearly match this board (blank display, or clock works with no heat) rather than the switch membrane's symptoms (some buttons unresponsive, others fine), replacing just this board is usually sufficient. Does this board include the digital clock and display? Yes. This is a combined control board and clock assembly — the digital display for time and temperature settings is part of this same board, not a separate component. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It includes the same processor, relay switching, and display circuitry as the control board originally installed in your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11176454 Gas Range Oven Igniter The XPARTCO W11176454 is an aftermarket replacement oven burner igniter compatible with select Whirlpool, Maytag, and Amana gas ranges. The igniter is a hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without lighting the burner. This igniter draws 3.3–3.6 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F with a heating time of approximately 17 seconds. The igniter body measures 3-7/10 inches (Length A) with 9-1/2 inch leads and two separate connectors. It directly replaces OEM part numbers W11176454 and W10914411, and is compatible with Whirlpool WFG and WFG505 series, Amana AGR and AGG series, and select Maytag gas range models. Installs in 10–20 minutes with basic hand tools. Quick Answer The XPARTCO W11176454 Gas Range Oven Igniter fixes Whirlpool, Maytag, and Amana gas ovens that won't heat, take too long to preheat, or have an igniter that glows but never lights the burner. Silicon carbide construction. Draws 3.3–3.6A at 120V. Igniter body 3-7/10" with 9-1/2" leads and 2 separate connectors. Replaces W10914411. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat (weak igniter not reaching ignition temperature) Igniter glows orange or red but never lights the gas burner Smell of gas when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Clicking sounds from the oven without successful ignition Oven element will not heat despite other components functioning normally Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11176454, 4547416, W10914411, EAP12348439, AWP43029, PD00044759, AP6327293, PS12348439. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands: Whirlpool gas ranges — WFG320 and WFG505 series (freestanding) Amana gas ranges — AGR and AGG series Maytag gas ranges — select AGR series models Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance vs. standard ceramic igniters Draws 3.3–3.6 amps at 120V AC — correct range to open the Whirlpool gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 17-second heat-up time Igniter body length: 3-7/10 inches; lead length: 9-1/2 inches Two separate connectors for easy plug-in installation Directly replaces W11176454 and W10914411 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with a screwdriver Product Specifications Part Number W11176454 Also Replaces W10914411 Part Type Oven Burner Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Material Silicon Carbide Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Resistance 40 – 800 Ohms Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 17 seconds Igniter Body Length (A) 3-7/10 inches Lead Length 9-1/2 inches Connectors 2 separate connectors Compatible Brands Whirlpool, Amana, Maytag Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Installation Instructions Unplug the range and shut off the gas supply before beginning. Open the oven door and remove the oven racks. Lift and remove the oven bottom panel by unscrewing the retaining screws. Remove the heat shield (if present) to expose the burner and igniter assembly. Unscrew the igniter mounting screws — typically one or two — and carefully disconnect the wire connector. Connect the new W11176454 igniter to the wire harness using the two separate connectors, secure it to the burner bracket with the mounting screws, then reinstall the heat shield and oven bottom panel. Restore gas supply and power and run a test cycle to confirm the oven lights correctly. Important: Do not touch the silicon carbide igniter element with bare hands — oils from skin reduce its lifespan. Handle only by the bracket and leads. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between W11176454 and W10914411? The W11176454 is the updated part number that directly supersedes the older W10914411. Both are the same hot surface igniter for compatible Whirlpool, Amana, and Maytag gas ranges. This aftermarket replacement is compatible with both part numbers. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than usual to preheat, or the igniter glowing orange but never lighting the burner. A working igniter reaches ignition temperature within about 30–90 seconds and glows bright orange. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Why does my igniter glow but the oven still won't heat? This is the classic symptom of a weak igniter. The gas safety valve requires a minimum amperage draw — typically around 3.2 amps — to open and allow gas to flow to the burner. As the igniter ages, its resistance increases and amperage drops below this threshold. The igniter still glows because it has some current, but not enough to open the valve. Replacing the igniter resolves this in nearly all cases. Is the W11176454 compatible with my Amana or Maytag range? Yes — the W11176454 is compatible with select Amana AGR and AGG series gas ranges and select Maytag AGR series models in addition to Whirlpool WFG320 and WFG505 series ranges. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from silicon carbide to match the electrical specifications and performance of the original W11176454 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat The WP4449751 is a Genuine OEM Whirlpool replacement oven high limit thermostat compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens, wall ovens, microwave-oven combinations, and ranges. The high limit thermostat is a critical safety device mounted near the oven cavity — it continuously monitors the oven's temperature and cuts off electrical power to the heating element if the oven exceeds its safe operating temperature. When the oven temperature drops back to normal, the thermostat closes and allows normal operation to resume. This backup safety layer protects against fires, damage to the oven, and unsafe cooking conditions when the main temperature control fails. Rated to trip at approximately 335°F (170°C). Common causes for the high limit thermostat to trip include a faulty control board, cooling fan failure, blocked ventilation, poor door sealing, disrupted air circulation, or an abnormal self-cleaning cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the WP4449751 directly replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549. Installs in 30–45 minutes with basic hand tools by experienced DIYers. This is a safety component in a 240V oven circuit — proceed only if you're comfortable with high-voltage electrical work, or call a qualified appliance technician. Quick Answer The WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore ovens with symptoms including oven not heating, oven overheating, uneven heating, oven failing to start, and self-clean door won't unlock after cycle. 335°F (170°C) trip temperature — cuts off power to heating element on overheat, then resets when temperature returns to normal. Genuine OEM. Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, AH11742549. Compatible with WOS/WOD wall ovens, KOSE/KODE/KOCE series, JJW/JMW/JDRP/JDR series, and many more. Common Problems This Part Fixes Oven not heating at all — high limit thermostat tripped open Oven overheating — thermostat failing to trip when needed (rare failure mode) Inconsistent oven temperatures leading to undercooked or overcooked food Oven fails to start when powered on Oven door won't unlock after a self-cleaning cycle completes Uneven heating — hot spots or cold spots inside the oven cavity Oven cuts off heat mid-cycle without reaching set temperature F-code or thermostat-related error displayed on the control panel Multimeter continuity test on the thermostat shows an open circuit at room temperature Visible damage or discoloration on the thermostat housing from a prior overheat event Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven high limit thermostat directly replaces the following OEM and cross-reference part numbers: WP4449751, 4449751, 1550872, AP6009390, AWP47600, EAP2375382, PD00025977, PS11742549 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high limit thermostat is compatible with select ovens, wall ovens, ranges, and microwave-oven combinations from the following brands: Whirlpool wall ovens — WOS series (WOS31ES0JS, WOS51EC0AS, WOS51EC0HS, WOS51EC7HW02, WOS51EC7HW21, WOS72EC0HS/HV, WOS72EC7HS/HV, WOS92EC0/EC7 all revisions, WOS97ES0ES series) Whirlpool double wall ovens — WOD series (WOD51EC0AW03, WOD51EC7HS, WOD93EC7AS) Whirlpool combination wall ovens — WOC54EC0/EC7 series KitchenAid wall ovens — KOSE, KODE, and KOCE series (KOSE500ESS, KODE500ESS, KOCE500ESS, KOCE500EBL00/EBL01/EBL02/EBL04/EBL05) Jenn-Air wall ovens — JJW, JMW, JDRP, and JDR series (JJW2427DB/DS 00/01, JJW2430DS, JJW3430DS, JMW2430DS, JDRP430HL/HM 00/01, JDRP430WP00, JDRP436HL/HM/WP series, JDRP536HL/HM/WP series) Maytag wall ovens and ranges (select models) Amana wall ovens (select models — AWO6313SFB00/02, AWO6313SFS00/02, AWO6313SFW00/02) KitchenAid ranges — KDRS407 series (KDRS407VBK01, KDRS407VBU01, KDRS407VSS00) Whirlpool ranges — IBD350DS00, IBS300DS00, IBS350DS00 series Magic Chef, Admiral, Norge, Roper wall ovens (select Whirlpool-built models) Kenmore / Sears wall ovens (select Whirlpool-built models) Suitable for single or double electric wall ovens and microwave-oven combination units Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance High limit thermostat (safety switch) — cuts off power to the oven's heating element when temperature exceeds 335°F (170°C) to prevent overheating damage or fire Auto-reset design — closes and restores normal operation when the oven temperature returns to safe range Precision-calibrated to Whirlpool factory specifications for accurate trip temperature and reliable safety response One-year Whirlpool warranty on Genuine OEM parts Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549 Compatible with Whirlpool WOS/WOD/WOC series, KitchenAid KOSE/KODE/KOCE series, Jenn-Air JJW/JMW/JDRP/JDR series, plus Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens Fits single wall ovens, double wall ovens, ranges, and microwave-oven combination units Resolves "oven won't heat," "overheating," "uneven heating," "self-clean door stuck locked," and "won't start" symptoms when caused by a failed high limit thermostat For experienced DIYers or qualified appliance technicians — this is a safety component in a 240V oven circuit Installation typically takes 30–45 minutes with basic hand tools Product Specifications Part Number WP4449751 Part Type Oven High Limit Thermostat (Safety Switch) Condition Genuine OEM Application Wall Ovens, Ranges, Microwave-Oven Combinations (Whirlpool platform) Trip Temperature 335°F (170°C) Type Auto-Reset (closes when temperature returns to safe range) Warranty One-Year Whirlpool Warranty (Genuine OEM) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Turn Off Power at Breaker Before Starting — This Is a 240V Oven Circuit — Wear Work Gloves Disconnect power at the household breaker before beginning — this is a 240V circuit and there is a serious risk of electrical shock if power is not fully disconnected. Verify power is off with a voltage tester before touching any wiring. Wear work gloves and safety glasses. Allow the oven to cool completely before beginning (several hours after any recent cooking). The high limit thermostat is typically mounted on the rear or side of the oven cavity, accessed by removing the back panel of the appliance (for freestanding ranges) or the front trim/service panel (for wall ovens). The exact location varies by model — consult your appliance's service diagram before starting. Photograph all wire connections and mounting details before disconnecting anything. Disconnect the wire terminals from the old thermostat (typically two spade-terminal wires). Remove the mounting screws or clips holding the thermostat to the oven cavity, and lift it out. Install the new WP4449751 in the exact same position and orientation — the thermostat must be in good thermal contact with the oven cavity to function correctly. Secure the mounting hardware and reconnect the wires to their correct terminals. Reinstall the access panels. Restore power at the breaker and test the oven — start with a low-temperature bake cycle to confirm normal heating operation before running a high-temperature or self-clean cycle. Tools needed: Phillips screwdriver, 1/4" nut driver, voltage tester (essential), work gloves, safety glasses. Frequently Asked Questions Why did my high limit thermostat trip in the first place? A high limit thermostat trips because the oven exceeded its safe operating temperature — meaning something upstream in the temperature control chain failed to shut off the heating element when it should have. Common causes are: a failed oven control board (relay stuck closed), a failed cooling fan (allowing the oven cavity or electronics to overheat), blocked or restricted ventilation, poor door sealing (letting the cavity overheat), disrupted air circulation, or an abnormal self-cleaning cycle. Before installing the new thermostat, investigate and address the underlying cause — otherwise the new thermostat will trip again in short order. Also inspect the ventilation, oven door gasket, and cooling fan while you have the appliance open. What's the difference between a high limit thermostat and the operating thermostat? These are two different components serving two different roles. The operating thermostat (or the oven control board with its temperature sensor) is the primary component that maintains the oven at your set temperature by cycling the heating element on and off during normal operation — it opens and closes at your selected temperature (e.g., 350°F). The high limit thermostat (WP4449751) is a backup safety device that only trips when the oven temperature far exceeds normal operation (335°F over the cavity's safe threshold), typically because the operating thermostat or control has failed. If the high limit thermostat trips, both need to be checked — the operating thermostat may also need replacement. Does the high limit thermostat reset itself, or does it need to be replaced after tripping? The WP4449751 is an auto-reset thermostat — it closes automatically once the oven cools back to a safe temperature, allowing normal operation to resume. If your oven is heating normally again after cooling, the thermostat is likely still functional (the underlying overheating cause needs investigation). However, if the thermostat has failed permanently open — often the result of repeated overheat events or age — it will need replacement. Test with a multimeter set to continuity: a working thermostat shows continuity at room temperature. If it reads open (infinite resistance) when cold, it has failed and needs replacement. Why does my self-cleaning cycle leave the oven door locked and the oven won't heat? This is a classic symptom of a high limit thermostat that tripped during the self-clean cycle. Self-cleaning cycles run at extreme temperatures (800–1000°F) and stress every component in the oven — if the ventilation, door gasket, or cooling fan can't keep up, the high limit thermostat will trip open. Once tripped, the oven can't heat OR unlock the self-clean door lock mechanism, leaving the door stuck closed. Once the thermostat cools and closes (or is replaced), the door lock releases and normal operation resumes. If self-clean cycles routinely trip the thermostat, investigate whether the ventilation, cooling fan, or door gasket are causing the problem. Can I do this repair myself, or should I hire a technician? Replacing an oven high limit thermostat is a manageable DIY repair for someone comfortable with mechanical work and electrical connections, but this is a 240V circuit and the thermostat is a safety component — any error can create a serious safety risk. If you have experience with appliance repair, follow the safety precautions carefully (breaker off, voltage tester, correct thermostat orientation), and can confirm the wiring connections are secure, this is a feasible DIY. If you've never worked with 240V appliance circuits before, hiring a qualified appliance technician is the safer option. Also identify and address whatever caused the original overheat event — otherwise the new thermostat will trip again. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same high limit thermostat installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens from the factory — guaranteed fit, materials, and performance. Backed by Whirlpool's one-year warranty on Genuine OEM parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10545291 Genuine OEM Whirlpool Range / Oven Thermal Fuse The WPW10545291 is a genuine Whirlpool OEM thermal fuse mounted next to the heating source inside wall ovens, ranges, and microwave-oven combo units. This fuse is a one-time safety device: as long as the oven stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — most often during a self-clean cycle, which runs far hotter than normal baking or roasting — the fuse permanently opens the circuit and cuts power. That's why a blown thermal fuse produces such a distinctive symptom: the oven loses power completely, sometimes with the door still electronically locked from the self-clean cycle that triggered the failure. Unlike a thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. Because it's mounted directly behind the control panel on many wall oven models, replacing it typically means pulling the unit partway out from the wall and removing the control section to reach it, rather than a simple rear-panel swap. It directly replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, and W10436435. Quick Answer The WPW10545291 Genuine OEM Whirlpool Range / Oven Thermal Fuse fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall ovens, ranges, and microwave-oven combos that lost power completely — often right after a self-clean cycle. Replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, W10436435. If the door is electronically locked and won't open, you may need to manually release the lock before you can access the oven for this repair — see the FAQ below. Common Problems This Part Fixes Oven has no power at all — no lights, no display, no response to any button Oven lost power suddenly, especially during or right after a self-clean cycle Oven door remains electronically locked with no power to release it Oven that stopped working after running unusually hot Control panel completely dark and unresponsive Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range/oven thermal fuse directly replaces the following OEM and cross-reference part numbers: WPW10545291, W10545291, 3021646, W10436435, AP6022803, AWP50815, EAP11756140, PD00032820, PS11756140. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Whirlpool wall ovens, ranges, and microwave-oven combo units, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances built on the Whirlpool platform, including model numbers such as WOD77EC7HS, WOD77EC0HV, and WOD51EC7AB02. Note: Whirlpool uses several different thermal fuses across its range/oven lineup, including separate fuse designs used in other model families. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration One-time safety device that cuts power if the oven overheats Resolves "no power at all," "lost power after self-clean," and "door locked with no power" symptoms caused by a blown fuse Mounts next to the heating source, typically behind the control panel Replaces AP6022803, W10545291, 3021646, PS11756140, PS7783661, and W10436435 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall ovens, ranges, and microwave-oven combos Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10545291 Part Type Range / Wall Oven Thermal Fuse Condition Genuine OEM Brand Whirlpool Application Wall Ovens, Ranges, Microwave-Oven Combo Units Location Next to the heating source, typically behind the control panel Resettable No — one-time use, must be replaced once blown Repair Difficulty Moderate to Hard — control panel disassembly required on many models Quantity 1 thermal fuse Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Oven Or Shut Off Breaker Before Starting — Access Is Typically Behind The Control Panel Shut off the oven's power at the breaker before beginning. Wear work gloves. If the door is electronically locked and won't open due to the power loss, you may need to manually release it first — see the FAQ below for a common workaround. Remove the oven's retaining screws and carefully pull the unit out from the wall a few inches to access the screws holding the control section in place. Remove the screws securing the control panel — typically four — and pull the control unit loose, letting the display ribbon cable stay connected while you rest the panel out of the way on top of the oven; avoid pulling it further than the ribbon allows. The thermal fuse is usually mounted right behind the control panel at this point. Photograph the wiring before disconnecting the old fuse's connectors. Pull the connectors off the old fuse and plug them onto the new WPW10545291 fuse in the same orientation. Reconnect the control panel's ground wire and ribbon cable, reinstall the control panel and its screws, and carefully push the oven back into the wall opening, securing it with its retaining screws. Restore power at the breaker and confirm the oven powers on normally and the door unlocks and operates correctly. Tools needed: Phillips screwdriver, power tester (helpful), work gloves. Frequently Asked Questions My oven lost all power right after a self-clean cycle. Is this the thermal fuse? Yes, this is one of the most common and well-documented triggers for this exact failure. Self-clean cycles run at extremely high temperatures compared to normal cooking, and if that heat exceeds what the thermal fuse is rated to tolerate, it blows to protect the oven — cutting all power in the process. A total loss of power during or shortly after a self-clean cycle is a strong sign this fuse is the cause. My oven door is locked and I have no power to release it. How do I get it open? This is a known complication when the thermal fuse blows during or after a self-clean cycle, since the door lock can remain engaged with no power available to release it electronically. One documented workaround: with the house power to the oven confirmed off, some owners have used a thin, flexible material (such as a bent paper clip or a flexible cutting board edge) worked carefully between the door and the lock mechanism to manually trip the lock open. This varies by model and takes patience — if you're not comfortable attempting it, a qualified appliance technician can open the door safely. Can I just reset the thermal fuse instead of replacing it? No. Unlike a thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your oven, range, or microwave-oven combo. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer The 00770657 is a genuine Bosch OEM cutlery drawer — a dedicated third-rack silverware caddy that sits in the upper interior of the dishwasher tub, above the top rack, on select Bosch dishwashers equipped with a third rack add-on compartment. Rather than loading silverware into a basket down in the lower rack, this drawer holds forks, spoons, and knives flat in their own dedicated level, laid out individually with room around each piece so water and detergent can reach every surface. It rides on durable rollers along rails built into the tub, sliding smoothly in and out for loading and unloading, and its position at the top of the tub gives it a clear, unobstructed line to the upper spray arm for targeted cleaning. The tray and support grid inside the drawer are open enough to let water flow freely through while still keeping utensils separated and organized. Because it's a lightweight tray sitting in a hot, wet, chemically active environment for years, common failure points include a metal frame that rusts through and eventually collapses under its own weight, plastic that becomes brittle or begins visibly disappearing from years of heat exposure, and dividers that crack or break, letting silverware jumble together. It directly replaces AP5788109, 00689507, 3279853, and PS8747441. As a genuine OEM part, the 00770657 is manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer fixes Bosch (and compatible Thermador, Gaggenau, and select Kenmore) dishwashers with a third-rack cutlery drawer that has rusted through, has cracked or broken dividers, has become gummy or sticky and won't slide smoothly, or has cracks exposing silverware to the heating element below. Rides on rollers for smooth in-and-out extension. Replaces AP5788109, 00689507, 3279853, PS8747441. This is the roller-equipped cutlery drawer — a similar-looking companion part, 00770656, is a different drawer design without rollers, so double-check which one your dishwasher uses. Common Problems This Part Fixes Metal frame of the cutlery drawer rusted through or visibly corroding Drawer frame collapsing or sagging under the weight of silverware Missing or broken dividers letting silverware commingle instead of staying separated Drawer glides that have become gummy or sticky from food residue buildup, obstructing smooth movement Cracks or holes in the drawer exposing silverware to direct contact with the heating element Plastic that has become brittle, discolored, or is visibly disappearing after years of heat exposure Silverware not getting fully clean due to poor spray coverage from a warped or damaged drawer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher cutlery drawer directly replaces the following OEM and cross-reference part numbers: 00770657, AP5788109, 00689507, 3279853, ABS12031, EAP8747441, PD00043732, PS8747441 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cutlery drawer is compatible with select Bosch dishwashers equipped with a third rack add-on compartment, and is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers configured with a triple-rack setup, including model numbers such as: SHE68T52UC, SHE68T55UC, SHE68T56UC, SHE68TL5UC SHE863WF5N, SHE863WF6N SHP65T56UC, SHP65TL2UC SHV68T53UC, SHV68TL3UC, SHV863WD3N SHVM63W53N, SHXM63W55N, SHXM63WS5N Each of these models spans multiple production suffixes (such as /01, /02, /07, and /09) — check your full model and production number for exact confirmation. Note — check for rollers: This drawer rides on rollers. A similar-looking companion part, 00770656, is a separate cutlery drawer design used on other Bosch/Thermador/Gaggenau models without the roller mechanism. The two are not interchangeable. Check whether your existing drawer slides on visible rollers before ordering, and always verify your full model and production number. Contact our support team with your model number if you're unsure which drawer fits your dishwasher. Key Features Genuine Bosch OEM part — factory-specified frame, grid, and roller mechanism Dedicated third-rack cutlery drawer positioned above the top rack for optimal spray-arm targeting Resolves "rusted frame," "broken dividers," "sticky glides," and "cracked drawer" symptoms caused by wear and corrosion Multi-level basket layout keeps silverware separated for full surface exposure to wash spray Rides smoothly on rollers for easy extension and retraction when loading and unloading Open tray and support grid design allows water and detergent to flow through freely Direct drop-in replacement — no tools required, simply slides into place on existing rails Replaces AP5788109, 00689507, 3279853, and PS8747441 Compatible with Bosch, Thermador, Gaggenau, and select Kenmore third-rack dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 00770657 Part Type Dishwasher Third-Rack Cutlery / Silverware Drawer Condition Genuine OEM Brand Bosch Location Upper interior of the tub, above the top rack Mounting Rides on rollers along built-in tub rails Design Multi-level basket grid with open tray for water flow Repair Difficulty Very Easy — no tools required Quantity 1 cutlery drawer Compatible Brands Bosch, Thermador, Gaggenau, select Kenmore Installation Notes This is one of the simplest repairs in the entire dishwasher — no tools, no wiring, and no water lines to disconnect. Open the dishwasher door fully. Locate the existing cutlery drawer at the top of the tub, above the upper rack, and slide it forward and out along its rails until it clears the cabinet. Line up the new 00770657 drawer with the same rollers and rails, and slide it in until it seats fully at the back of the tub. Close the door and run a cycle to confirm the drawer sits securely and doesn't rattle or shift during operation. Frequently Asked Questions Does my drawer use rollers, or is it the other style? Slide your existing drawer out partway and look underneath or along the sides — this 00770657 drawer rides on visible roller wheels along the tub rails. If your drawer instead has a simpler glide track with no rollers, you likely have the companion part, 00770656, which is a different design used on other models. The two aren't interchangeable, so it's worth confirming before ordering. My drawer's metal frame has rusted through. Is that just cosmetic, or should I replace it? It's worth replacing rather than living with it. Once the metal frame starts rusting through, it typically continues to weaken and can eventually collapse under the weight of loaded silverware, sometimes suddenly. Customers who've dealt with this describe the original frame rusting to the point of failure over time — replacing it before it fully gives out avoids a mid-cycle collapse and keeps your utensils properly organized and exposed to the wash spray. Do I need any tools to install this? No. This is a genuinely tool-free repair — slide the old drawer out along its rails, then slide the new one in until it seats. Customers consistently describe this as one of the easiest dishwasher parts to swap. I see cracks or holes in my drawer near the bottom. Is that a safety concern? It can be, depending on where the damage is. If cracks or holes are positioned where silverware could shift down and make direct contact with the dishwasher's heating element, that's worth addressing rather than ignoring, since it can affect both the cleaning process and the condition of your utensils over repeated cycles. Replacing a cracked or holed drawer resolves this. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original roller mechanism, basket grid layout, and dimensions of the cutlery drawer originally installed in your third-rack-equipped Bosch, Thermador, Gaggenau, or compatible Kenmore dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 00619985 Dishwasher Mounting Bracket Kit - Compatible with Bosch, Thermador, Gaggenau, Kenmore Dishwashers Product Description Secure your dishwasher with the replacement XPARTCO 00619985 Mounting Bracket Kit. This kit provides sturdy brackets to fasten select Bosch, Thermador, Gaggenau, and Kenmore dishwashers to kitchen cabinets or countertops, ensuring stability and preventing tipping. It addresses issues like loose mounting, excessive vibration, or noise during operation, offering a cost-effective alternative to OEM parts. Note: Includes two mounting brackets and mounting screws (for top or side installation). Disconnect power before installation. Verify countertop or cabinet suitability for mounting. Replaces part numbers: 00619985, 00628371, 00605007, 1567804, 605007, 619985, 628371, AH3478789, EA3478789, PS3478789, PD00000071, AP4538351, PS8728568. Compatibility: Compatible with models including but not limited to: Bosch: SHX88PW55N/01, SHX89PW55N/01, SHX33M06UC/46, SHX33M05UC/46, SHX33M02UC/53, SHX33M02UC/52, SHX33M02UC/50, SHX33M02UC/46, SHEM3AY55N Thermador: DWHD94EP/50 Gaggenau: Select models requiring 00619985 Kenmore: Select models requiring 00619985 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Bosch, Thermador, Gaggenau, and Kenmore dishwashers. 🔥 Specifications: replacement mounting bracket kit, includes two stainless steel brackets and two 1.5" hex-head screws for top or side mounting. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, wrench, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves loose or unstable mounting, excessive vibration, or noise during operation. Product Specification Part Number: XP619985 Component Type: Mounting bracket kit Material: Stainless steel Weight: 3.0 oz (kit) Mounting Hardware: Includes two 1.5" hex-head screws Operating Conditions: Suitable for high-humidity kitchen environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dishwasher from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher stable and secure today! Add to cart now for a budget-friendly fix!

Read more less

4581DD3002ACM Dishwasher Upper Dishrack Roller Upper rack roller for LG & Kenmore Elite Dishwashers. Sold individually, but recommend replacing in sets. Includes roller and clip on axel. Replaces Part Numbers: 4581DD3002A, 4581DD9001B, 1266813, AH3523050, EA3523050, AP4437685, PS3523050.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less