Search results for "Washer Board"

WH22X38697 Washer Genuine Control Board Fits Specific GE Washer Model Main Control Board Fl Washer Le W/instructions Replaces Part Numbers: WH22X38697, WH22X37837, WH22X36638, WH22X32458, WH22X35518, WH22X30897, WH22X29546, WH22X32058, WH22X34660, WH22X36858, WH22X37838, AP8054699, PS17874598.

Read more less

WH12X10614C Washer Genuine Electronic Control Board Replaces Part Number: WH12X10614C, WH12X10614, WH12X10538, AP8056060.

Read more less

WH22X37840 Genuine OEM GE Washer Main Control Board The WH22X37840 is a genuine GE OEM main control board for GE and Profile UltraFresh front-load washers. This board is the washer's central processor — it reads every button press and cycle selection, drives the motor and inverter, opens and closes the water valves, runs the drain pump, and continuously monitors water level through an integrated water pressure switch built into the board itself. Because so many functions route through this single board, a failing control board can produce almost any symptom: a washer that won't power on, won't start a cycle, stalls partway through, fails to fill or drain, or runs a cycle that doesn't match what was selected on the display. This board revises and supersedes WH22X36637, and also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, and WH22X37839. As a genuine OEM part, the WH22X37840 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Important: this board is not universal across GE's front-load lineup. It must be matched to your specific model and, after installation, programmed with the correct "personality" code for your washer before it will operate properly. Quick Answer The WH22X37840 Genuine OEM GE Washer Main Control Board fixes GE and Profile UltraFresh front-load washers that won't power on, won't start, stall mid-cycle, fail to fill or drain, run the wrong cycle, or have an unresponsive control panel. Genuine OEM, includes an integrated water pressure switch. Revises WH22X36637; also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, WH22X37839. Fits GFW650S, GFW850S, PFW870S, and PFW950S platforms. Requires programming a model-specific "personality" code after install, and the drain pump must be confirmed good before installing — a failed pump can damage a new board. Common Problems This Part Fixes Washer won't power on or the display stays completely dark Washer won't start a cycle even though buttons respond and lights come on Cycle stalls or stops partway through with no error explanation Washer won't fill with water, or fills but never advances to wash Washer won't drain or won't spin at the end of a cycle Control panel unresponsive — button presses do nothing, or the wrong cycle runs Display shows scrambled characters, flashing LEDs, or a persistent error code Washer runs erratically — random starts, stops, or cycle changes on its own Board that failed after repeated cycles where the drain pump was struggling Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer main control board directly replaces the following OEM and cross-reference part numbers: WH22X37840, WH22X36637, WH22X35517, WH22X34659, WH22X30898, WH22X29532, WH22X32057, WH22X32457, WH22X36857, WH22X37839, AP7245609, AGE26864, PD00089582, PS17874601. WH22X36637 was the immediately preceding number that GE revised to WH22X37840. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This main control board is compatible with select GE and Profile UltraFresh front-load washers, including: GE front-load washers — GFW650S series GE front-load washers — GFW850S series GE Profile front-load washers — PFW870S series GE Profile front-load washers — PFW950S series Verified model numbers include: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN3SN, GFW650SPN4SN, GFW650SSN4WW, and PFW955SPW0DS. Note: This board only works for the specific GE and Profile models listed above and must be programmed with the correct personality code for your washer after installation. It is NOT a universal front-load control board. If your model number is not listed above, ordering this board is likely to result in a board that installs but never runs correctly. Always verify your full model number before ordering, and contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified firmware, relay switching, and sensor interface Functions as the washer's central processor, coordinating the motor, inverter, water valves, and drain pump Includes an integrated water pressure switch — not available or serviceable as a separate part Resolves "won't power on," "won't start," "stalls mid-cycle," "won't fill or drain," and "unresponsive control panel" symptoms caused by control board failure Revises and directly replaces WH22X36637 and 7 additional legacy board numbers Direct drop-in replacement for the original board mounting and harness connectors Fits GFW650S, GFW850S, PFW870S, and PFW950S GE and Profile UltraFresh platforms Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH22X37840 Part Type Washer Main Control Board (Electronic Control Module) Condition Genuine OEM Brand GE / GE Profile Application GE and Profile UltraFresh Front-Load Washers Integrated Components Water pressure switch (built into board, not separately serviceable) Programming Required Yes — model-specific personality code must be set after installation Supersedes WH22X36637 Repair Difficulty Medium — top panel removal and electrical connections required Quantity 1 control board Compatible Models GFW650S, GFW850S, PFW870S, PFW950S series Installation Notes ⚠️ 240V Circuit — Unplug Washer Before Starting. Verify Drain Pump First. Board Requires Programming. Disconnect power at the outlet or shut off the circuit breaker before beginning; front-load washers on this platform run on a 120V/240V circuit and internal components can retain a charge briefly after power is removed. Before replacing the board, confirm the drain pump is working correctly. A drain pump that has been struggling, clogged, or intermittently failing can send the control board erratic electrical feedback that damages a brand-new board the same way it damaged the old one — replacing the board alone, without checking the pump, is one of the most common reasons a "new" board fails again within days. Access is typically through the top panel: remove the rear top screws and slide the panel back, then locate the control board housing (commonly behind the top-front console or in a housing near the top of the cabinet, depending on model). Photograph all harness connections before disconnecting anything — this board has numerous connectors and getting even one out of place will cause a no-start or miswired symptom. Ground yourself before handling the board to avoid static damage to its electronics. Remove the mounting screws, disconnect each harness connector, and lift the old board free. Install the new WH22X37840 in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Before closing the washer back up, you must program the board with the personality code specific to your model. This is done through a button sequence on the control panel — press and release Start repeatedly until the display shows the personality ID number for your model, then confirm to save it; the control will return to an idle state once accepted. GE's official instructions (publication 99-3000289) detail the exact sequence and a Field Service Mode test if the LEDs don't flash correctly after programming — follow those instructions rather than guessing at the code, since an incorrect personality setting will cause the washer to behave unpredictably. Once programmed, reassemble the top panel, restore power, and run a full test cycle to confirm normal fill, wash, drain, and spin behavior. Tools needed: Phillips screwdriver, nut driver, anti-static wrist strap (recommended), and access to GE's personality programming instructions for your model. Frequently Asked Questions Do I really need to program the board after installing it? Yes — this is not optional. The WH22X37840 is shared across several GE and Profile washer models, and it needs to be told which specific model it's installed in through a "personality" code before it will run correctly. Skipping this step, or entering the wrong code, will leave the washer behaving unpredictably even though the board itself is functioning normally. GE provides official programming instructions (publication 99-3000289) with the button sequence for your model — follow those closely rather than guessing. Why does the listing say to check the drain pump before installing this board? Because on this platform, a failing or clogged drain pump can feed electrical strain back into the control board that damages it over time — the same failure that likely killed your original board. If you install a new board without addressing a bad drain pump, there's a real risk of burning out the replacement as well. Before installing, run the pump through a diagnostic or physically inspect it for clogs, a seized impeller, or electrical failure, and address any issues found there first. My washer won't power on at all. Is this the right part? It's a strong candidate, but rule out the obvious first: confirm the outlet has power, check that the washer's power cord and connection are intact, and check the home's circuit breaker or a blown fuse. If those are all fine and the washer still shows zero signs of life — no lights, no display, no response to any button — the main control board has very likely failed and this board is the correct replacement. What's the difference between WH22X37840 and WH22X36637? They are the same board across production revisions. WH22X36637 was the prior GE part number and WH22X37840 is the current number that supersedes it. If your washer's parts diagram shows WH22X36637 or any of the older numbers (WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517), this listing is the correct replacement — it installs and programs the same way. Does this board include the water pressure switch? Yes. The water pressure switch that monitors fill level is integrated directly into this control board and is not available as a separate part per GE. If your washer's issue turns out to be water-level detection specifically — overfilling, underfilling, or an error related to water level — this board is the correct and only OEM fix, since the pressure switch cannot be replaced on its own. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It carries the same firmware, relay switching, integrated water pressure switch, and harness layout as the control board originally installed in your washer, and it is the officially supported replacement for your model once the correct personality code is programmed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11305308 Dishwasher Genuine Whirlpool Control Board Control Board  Main electronic control board. Fits Specific Whirlpool Dishwasher Models. Replaces Part Numbers:W11305308, W11131683, W10918994, W11170192, W11227807, AP6832578, PS12704681.

Read more less

XPARTCO 6501KW2001B Washer Rotor Positioning Sensor The XPARTCO 6501KW2001B is an aftermarket replacement rotor position sensor (RPS) compatible with a wide range of LG and Kenmore direct-drive front-load washers. This 5-pin Hall effect sensor mounts to the motor stator and monitors the speed and rotational direction of the motor rotor, feeding that data back to the control board so it can properly manage spin speed, direction changes during wash/rinse agitation, and load balancing. When this sensor fails or reads inaccurately, the control board loses the feedback it needs to run the motor correctly, and the washer commonly throws an "LE" (motor/rotor position) error code, fails to spin or agitate, or runs unusually long cycles as it struggles to detect motor movement. Built with PBT-GF30 housing and black epoxy potting for durability in the motor compartment. It directly replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 6501KW2001B Washer Rotor Positioning Sensor fixes LG and Kenmore (LG-built) direct-drive front-load washers throwing an "LE" error code, failing to spin or agitate, or running abnormally long cycles. 5-pin Hall effect sensor, PBT-GF30 housing, black epoxy potting. Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, 3282954. Classic symptom: washer displays "LE" and stops mid-cycle, or won't spin at all. Common Problems This Part Fixes Washer displays an "LE" (motor/rotor position) error code Tub fails to spin or agitate during the wash cycle Washer struggles to detect load movement, resulting in abnormally long cycle times Motor runs erratically or stalls mid-cycle Washer stops partway through a cycle without completing Inconsistent or failed direction changes during agitation Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This rotor position sensor directly replaces the following OEM and cross-reference part numbers: 6501KW2001B, 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, ALG52243, AP4457567, AP5973402, EAP11706506, 3282954, PD00059513, PS3529185, PS11706506 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This rotor position sensor is compatible with select LG-built direct-drive front-load washers, including: LG front-load washers (including WM1814CW, WM2010CW, WM2016CW, WM3455HW) Kenmore front-load washers (select LG-built models, including WD-3243RHD, WD-3245RHD, WD-3274RHD) Important: Do not confuse this with 6501KW2002B, which is a different, non-interchangeable rotor position sensor used on other LG washer platforms. Some newer LG models also integrate the Hall sensor directly into the motor stator assembly (such as AJB73816004) rather than using a standalone sensor like this one. Always verify your appliance model number before ordering, and check your parts diagram to confirm whether your model uses a standalone sensor. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement LG/Kenmore washer rotor position sensor (Hall effect, 5-pin) Resolves "LE error code," "won't spin," "won't agitate," and "long cycle time" symptoms Monitors motor rotor speed and rotational direction for accurate control board feedback PBT-GF30 housing with black epoxy potting for durability in the motor compartment Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954 Compatible with select LG and Kenmore (LG-built) direct-drive front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP6501KW2001B OEM Part Number 6501KW2001B Part Type Washer Motor Rotor Position Sensor Condition Aftermarket Replacement Sensor Type Hall Effect, 5-Pin Housing Material PBT-GF30 with black epoxy potting Application LG-Built Direct-Drive Front-Load Washer Motor Assembly Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning. Access the motor compartment, typically by removing the rear panel of the washer. Locate the rotor position sensor mounted to the motor stator near the rotor. Photograph the wiring before disconnecting, then unplug the sensor's connector from the wiring harness. Remove the mounting screw(s) or clip holding the sensor to the stator and remove the old sensor. Install the new 6501KW2001B sensor in the same position, taking care to seat it at the correct distance/orientation from the rotor magnets, and secure it. Reconnect the wiring harness connector, matching your photos. Reinstall the rear panel, restore power, and run a test cycle to confirm the washer spins and agitates normally without triggering an LE error code. Tools needed: nut driver or screwdriver, needle-nose pliers (for wiring connectors). Frequently Asked Questions My washer shows an "LE" error code — is this the part I need? This is one of the most common causes of an LE (motor/rotor position) error on LG and LG-built Kenmore washers. If your washer displays LE and stops mid-cycle or won't spin, this sensor is a likely culprit. That said, LE errors can also stem from the control board or a damaged wiring harness between the sensor and the board, so if replacing the sensor doesn't resolve the error, those components are the next things to inspect. Is this the same as the 6501KW2002B sensor? No — 6501KW2001B and 6501KW2002B are different, non-interchangeable rotor position sensors used on different LG washer platforms. Confirm your exact part number from your appliance's parts diagram before ordering, since these two are easy to mix up by their similar naming. My LG washer's parts diagram doesn't show a separate rotor position sensor — why? Some newer LG models integrate the Hall sensor directly into the motor stator assembly (such as part AJB73816004) rather than using a standalone sensor like this one. If your model doesn't list a standalone sensor, check whether your repair requires the full stator assembly instead. Contact our support team with your model number if you're unsure which one applies to your washer. Do I need any special tools to install this? No special tools — a nut driver or screwdriver to access the rear panel and remove the sensor's mounting screw(s), plus needle-nose pliers to help with the wiring connector. The main thing to get right is reinstalling the new sensor at the same position and orientation relative to the rotor as the original. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

 WH42X10650 Washer Control Panel, White Replaces Part Numbers: WH42X10650, AP3995175, 1264621, AH1482468, EA1482468, PS1482468. The WH42X10650 is a genuine GE replacement part, specifically designed as a control panel for GE washing machines. It houses and operates the control buttons and display, ensuring compatibility and reliability for your appliance.

Read more less

XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers Product Description Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422. Compatibility This replacement rotor position sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Aftermarket Replacement – Designed to match OEM performance and precision Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price Plug-and-Play Installation – No wiring modification required Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors Product Specification Part Number: 6501KW2002B Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: Durable printed circuit board with reinforced plastic housing Mounting: Direct-fit installation on stator assembly Operating Conditions: Rated for high-humidity, high-vibration washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) Installation Notes Tools Needed: 10 mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Unscrew the rotor bolt and carefully remove the rotor assembly. Locate and unplug the old sensor from the stator. Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs. Reconnect the wiring harness, reinstall the rotor, and secure the panel. Restore power and run a spin test to verify correct operation. ⏱️ Time Required: 20–25 minutes Shop With Confidence Trusted Appliance Parts Supplier 30-Day Return Policy Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO MFG63099101 Washer Door Strike (Door Lock Hook) The XPARTCO MFG63099101 is an aftermarket replacement washer door strike — also called a door lock hook or door latch hook — compatible with a wide range of LG front-load washers and Kenmore 796-series washing machines. The door strike is the metal hook component mounted on the inside edge of the washer door. When the door closes, the hook enters the door lock switch on the front panel and engages the electromagnetic lock mechanism, signaling the control board that the door is closed and locking it for safe operation during wash and spin cycles. Without an intact door strike, the lock can't grip anything, and the washer will not start. When the strike breaks — typically from repeated use, sudden impact, or stress over thousands of door cycles — the washer will not start, may stop mid-cycle, may display DE1 or DE2 error codes, leak water around the door, or fail to lock altogether. It directly replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132. Important: replacing the strike requires removing the inside door panel to access the hook — note that the inner glass insert is loose during disassembly and must be handled carefully. Often replaced alongside the matching door lock switch (EBF61315802, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO MFG63099101 Washer Door Strike fixes LG and Kenmore 796-series front-load washers where the door won't lock, won't start, stops mid-cycle, displays DE1 or DE2 errors, or leaks at the door. Metal hook attaches to the inside of the washer door — engages the lock switch when the door closes. Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132. Often paired with the door lock switch (EBF61315802, sold separately). Common Problems This Part Fixes Washer door not latching properly — strike broken or worn down Washer not starting because the door isn't detected as locked Washer stopping mid-cycle due to a door fault DE1 or DE2 error codes displayed on the control panel Minor water drips or leaks around the door during operation — door not sealing because the strike isn't fully engaging Door strike visibly broken, chipped, or missing on the inside edge of the door Door not staying closed — strike worn from repeated impact Washer not powering on Replaces Part Numbers This washer door strike directly replaces the following OEM and cross-reference part numbers: MFG63099101, 2759645, AGF77417823, PD00046132, EAP8752721, AP5787149, PS8752721. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the number printed on your original door hook may be a production batch code rather than the OEM part number — this does not affect fit. Compatibility This door strike is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3170CW/00, WM3180CW series LG front-load washers — WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HVA/01, WM3370HWA, WM3370HWA/01, WM3370HWA/00 series LG front-load washers — WM3400CW, WM3500CW, WM3500CW/00, WM3555HWA, WM3555HWA/00 series LG front-load washers — WM3570HVA, WM3570HVA/00, WM3575CW series LG front-load washers — WM3600HVA, WM3600HWA, WM3600HWA/00, WM3670HRA, WM3670HRA/00, WM3670HVA, WM3670HWA series LG front-load washers — WM3700HVA, WM3700HWA, WM3770HVA, WM3770HWA series LG front-load washers — WM3900HBA, WM3900HWA series LG front-load washers — WM4000HBA, WM4000HWA, WM4270HVA, WM4270HVA/00, WM4370HKA, WM4370HWA series Kenmore / Sears washers — 796-series (79641162410, 79641162411, 79641262610, 79641283310, 79641283311, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641482410, 79641482411, 79641483410, 79641483411, 79641582410, 79641582411, 79641583211, 79641583410, 79641583411, 79641962610, 79641963610 and many related models) Note: If both the door strike (MFG63099101) and the door lock switch (EBF61315802) have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new strike. Always verify your model number before ordering. Key Features Metal door strike (door lock hook) — mounts to the inside edge of the washer door and engages the door lock switch when the door closes Resolves DE1 and DE2 error codes when caused by a broken door strike on compatible LG and Kenmore washers Restores the proper engagement between the door and latch assembly for a firm, consistent connection every cycle Durable metal construction — designed to withstand repeated opening and closing impact Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132 Compatible with LG WM1388, WM3050, WM3170, WM3270, WM3370, WM3500, WM3570, WM3600, WM3670, WM3700, WM3770, WM3900, WM4000, WM4270, WM4370 series and Kenmore 796-series front-load washers Often replaced together with the door lock switch (EBF61315802, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number MFG63099101 Part Type Washer Door Strike (Door Lock Hook / Latch Hook) Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore LG-built platform) Location Inside edge of washer door Material Metal Often Paired With Door Lock Switch (EBF61315802, sold separately) Error Codes Resolved DE1, DE2 (when caused by broken strike) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Don't Drop the Inner Glass Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a broken strike, use a putty knife to pry the white latch on the door lock through the bottom service opening to release the door. With the door open, locate the screws around the perimeter of the inner door panel. Remove the screws to release the inner door panel from the outer frame. Important: the inner glass insert is loose once the panel is unscrewed — support the glass with one hand as you pry the panel away to prevent it from falling out and breaking. Note the orientation of the old door strike (the direction it points and how it's seated). Use needle-nose pliers or tweezers to pull out the retaining pin holding the old strike in place, then remove the broken strike. Install the new MFG63099101 strike in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Reinsert the retaining pin to secure it. Carefully reposition the glass insert into the door, reinstall the inner door panel, and tighten the screws. Restore power and run a test cycle to confirm the door locks properly and there are no leaks. Tools needed: Phillips screwdriver, needle-nose pliers or tweezers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door strike and the door lock switch? These are two separate parts that work together to lock the washer door. The door strike (MFG63099101) is the metal hook attached to the inside edge of the washer door — when the door closes, the hook is what physically enters the lock assembly. The door lock switch (EBF61315802) is the assembly mounted on the front panel just inside the door opening — it contains the electromagnetic mechanism that grips and locks the strike, and the electrical sensor that tells the control board the door is closed. If the strike is broken, the lock has nothing to grip and the washer won't start. If the switch is broken, the strike can still enter the slot but the lock won't engage or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing strike has broken off inside the lock or the lock won't release, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the strike installation. Always disconnect power from the washer first. The number on my old strike doesn't match — is it still compatible? In many cases, yes. LG sometimes prints production batch codes on door strikes that look like part numbers but don't match the official OEM part number. As long as your washer's parts diagram lists MFG63099101 (or one of its cross-references: AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132), this strike is the correct fit. If you're unsure, contact our support team with your washer model number and we'll verify before you order. Should I replace the door lock switch (EBF61315802) at the same time? Not always, but often. The strike and the lock switch work together as a pair — if one is worn, the other has typically experienced the same load over thousands of cycles and is approaching the end of its service life. When a broken strike is the cause of the failure, examine the lock switch when the panel is open: if the lock mechanism shows visible wear, doesn't grip the new strike firmly, or has corroded contacts, replace it at the same time. Since the door is already partially disassembled and you have the washer apart, doing both at once saves a second repair session. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal to match the dimensions, mounting configuration, and lock-engagement function of the original MFG63099101 door strike used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 Washer Water Inlet Valve (Cold) The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688995 Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less