Search results for "cooking hinge"

WB10X26769 Oven Genuine Door Hinge Replaces Part Number: WB10X26769, AP6331433, PS12342111. Description: This Door Hinge is a Genuine part for specific GE oven models. This door hinge consists of three parts, the spring, the hinge receiver and the hinge arm, which work together to support the weight of the door and ensure proper alignment. It allows the door to swing open and close securely, providing easy access to the appliance's interior.

Read more less

WB10X30271 Oven Genuine Door Hinge Replaces Part Number: WB10X30271, AP6331436, PS12342113. Description: This Door Hinge is a Genuine part for specific GE oven models. This door hinge consists of three parts, the spring, the hinge receiver and the hinge arm, which work together to support the weight of the door and ensure proper alignment. It allows the door to swing open and close securely, providing easy access to the appliance's interior.

Read more less

WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link The WD14X10009 is a Genuine OEM GE replacement dishwasher hinge arm link compatible with an exceptionally wide range of GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers — it fits over 2,100 models. The hinge arm link is the small plastic connector that joins the door spring to the door hinge arm at the bottom of the dishwasher door. This tiny part carries a big load: it's what allows the spring to counterbalance the weight of the door — especially when the door is open with a fully loaded lower rack resting on it. Without an intact link, the spring can't do its job, and the door drops open under its own weight instead of lowering in a smooth, controlled motion. The hinge arm link is a small piece of white plastic approximately 1-1/2" long, weighing about 0.01 lbs. It fails from ordinary wear and tear — thousands of open/close cycles gradually stress the plastic until it cracks or snaps. As a Genuine OEM part manufactured by GE to factory specifications, the WD14X10009 directly replaces AP2039321, 270839, AH259336, EA259336, and PS259336. Important: your dishwasher has a door spring and hinge arm link on BOTH the left and right sides. This part is sold individually — if one link has broken from age, the other is the same age and often not far behind, so many customers order two and replace both while the dishwasher is pulled out. Installs in 15–30 minutes with basic hand tools. Quick Answer The WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link fixes GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore dishwashers where the door falls open instead of lowering gently, the door won't stay shut or won't latch, the door is hard to open or close, or the door slants when open. Small white plastic link ~1-1/2" long — connects the door spring to the door hinge arm. Genuine OEM. Sold individually. Replaces AP2039321, 270839, AH259336, EA259336, PS259336. Fits 2,100+ GE-platform dishwasher models. There's one link on EACH side of the door — consider ordering two. Common Problems This Part Fixes Dishwasher door falls open instead of lowering in a smooth, controlled motion — no counterbalance from the spring Door drops down hard when opened — link broken, spring disconnected Door won't stay shut, or opens unexpectedly Door won't latch or lock properly Door is difficult to open or close Door slants or hangs unevenly when open Hinge arm link visibly cracked, bent, broken, or significantly worn Broken plastic link found lying on the floor beneath the dishwasher Door spring disconnected and hanging loose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher hinge arm link directly replaces the following OEM and cross-reference part numbers: WD14X10009, AGE24269, AP2039321, 270839, AH259336, EA259336, EAP259336, PD00023035, PS259336 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hinge arm link is compatible with an exceptionally broad range of dishwashers — over 2,100 models across the following brands: GE dishwashers — the vast majority of GE dishwasher models across many generations GE Profile dishwashers (including PDW-series models) Café dishwashers (select models) GE Monogram dishwashers (select models) Hotpoint dishwashers (select models) RCA dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Kenmore / Sears dishwashers (select GE-built models) Important — There Are TWO Links, One Per Side: Your dishwasher door has a spring and hinge arm link on both the left and right sides. This part is sold individually. Many customers discover the second link only after reinstalling the dishwasher — and since both links are the same age and have seen the same wear, the surviving one often breaks soon after. Consider ordering two and replacing both while the dishwasher is already pulled out. Also inspect the door hinge cable at the same time; if it's frayed, kinked, or bent, replace it too. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Hinge arm link — connects the door spring to the door hinge arm, allowing the spring to counterbalance the door's weight Enables the dishwasher door to open in a smooth, controlled motion rather than dropping open Supports the door's weight even when the lower rack is fully loaded and resting on the open door Prevents strain on the door hinges and door misalignment Small white plastic link, approximately 1-1/2" long, ~0.01 lbs Sold individually — note there is one link on each side of the door Replaces AP2039321, 270839, AH259336, EA259336, and PS259336 Fits over 2,100 dishwasher models across GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built lines Inexpensive fix for a problem that would otherwise cost a service call — many customers report the entire repair takes about 15 minutes DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WD14X10009 Part Type Dishwasher Hinge Arm Link (Door Spring Link) Condition Genuine OEM Application Dishwashers (GE platform) Length Approximately 1-1/2" Weight Approximately 0.01 lbs Color White Material Plastic Function Connects the door spring to the door hinge arm Location Bottom of the dishwasher door hinge, both left and right sides Quantity Sold individually (dishwasher uses TWO — one per side) Model Coverage Over 2,100 models Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. Remove the screws holding the bottom kick plate (a nut driver works well here) and the anchor screws at the top of the dishwasher that secure it to the countertop. Carefully pull the dishwasher out 8–10 inches from the cabinet to expose the door springs and hinge arm links at the bottom on both sides. (Depending on how the dishwasher is plumbed, you may be able to do this without disconnecting the water supply, drain line, or electrical — pull only as far as the connections allow, and disconnect them only if necessary for access.) Look at the hinge assembly at the bottom of the door: you'll see a steel cable with a hooked end, a spring, and the small white plastic link that ties them together. If the link is broken, it may already be lying on the floor. Remove the old link by disconnecting it from the hinge and spring — if it's cracked but still in place, you can break the remaining pieces free. Install the new WD14X10009: place the hinge arm link into the spring, hook the spring onto the clip, and seat the link into the clip on the hinge arm. Note: on some models the crimped hook opening on the steel cable is tight — if the new link won't slide in easily, a small file can carefully open the hook opening enough to accept it. Check the other side of the door while you're in there — there's a second spring and link, and if it's aged or cracked, replace it now. Push the dishwasher back into place, reinstall the anchor screws and kick plate, restore power and water, and test the door: it should now lower smoothly under spring tension rather than falling open. Tools needed: Nut driver, Phillips screwdriver, small file (occasionally), work gloves. Frequently Asked Questions My dishwasher door falls open instead of lowering gently — is this the part? Almost certainly, yes. The door spring is what counterbalances the door's weight so it lowers in a controlled motion. The hinge arm link is the small plastic piece that connects that spring to the door hinge arm. When the link cracks or snaps, the spring is effectively disconnected — so the door has no counterbalance and drops open under its own weight. This is the classic symptom. To confirm, pull the dishwasher out a few inches and look at the bottom hinge area on each side: if a link is broken, you'll often find the pieces on the floor or the spring hanging loose. If both links are intact, check the door hinge cable for fraying or the spring for damage. Should I order one or two? Order two. Your dishwasher has a door spring and hinge arm link on both sides of the door — and this part is sold individually. Many customers order one, replace the broken link, push the dishwasher back into the cabinet, and only then realize the second link exists (and is the same age, with the same wear). Since the tedious part of the job is pulling the dishwasher out from under the counter, replacing both links while you're already in there is the smart move. At a few dollars each, having a spare on hand is cheap insurance against doing the whole job over in a few months. Why do these little plastic links break? Ordinary wear and tear. The hinge arm link is a small plastic component that carries a surprising amount of load — every time you open the door, it transmits the spring's counterbalancing force to the hinge arm, and that load increases dramatically when the lower rack is fully loaded and resting on the open door. Over thousands of open/close cycles across years of use, the plastic fatigues and eventually cracks or snaps. It's a consumable wear item on GE dishwashers, which is exactly why GE uses the same inexpensive part across 2,100+ models. Do I have to disconnect the water and electrical to pull the dishwasher out? Often not. Many customers find that removing the top anchor screws and the bottom kick plate, then sliding the dishwasher out 8–10 inches, gives enough access to reach the hinge arm links — without disconnecting the water supply, drain hose, or electrical. It depends on how much slack your installer left in those lines. Pull the dishwasher out only as far as the connections allow, and see whether you can reach the hinge area. If the lines are too short and you can't reach, you'll need to disconnect the water supply, drain tube, and electrical (turn off power and water first). Either way, the link replacement itself takes only a few minutes once you can reach it. Should I replace the door hinge cable at the same time? Inspect it, and replace it if it shows any damage. The door hinge cable is the steel cable that connects the door spring assembly to the door hinge — it works alongside the link and spring in the same counterbalance system. If the cable is frayed, kinked, bent, or its crimped hook end is damaged, it will fail soon and you'll be pulling the dishwasher out again. Since you already have access, this is the ideal moment to check it. Also inspect the door spring itself for stretching or breakage. Contact our support team with your model number if you need the correct cable or spring part number. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same hinge arm link installed in compatible GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10500004 Genuine OEM Whirlpool Refrigerator Bottom Door Hinge & Cam Kit (Right, Gray) The W10500004 is a genuine Whirlpool OEM bottom door hinge and closing cam kit for the right side fresh food door on Whirlpool, Amana, KitchenAid, Maytag, Jenn-Air, Magic Chef, Roper, and Admiral refrigerators. This kit combines two related components: the bottom hinge, which supports the door's weight and lets it swing open and closed, and the closing cam, a plastic component that gives the door its final "pull" to close firmly on its own once you've pushed it most of the way shut. Finished in Apollo Gray, this kit measures approximately 4.65" x 4.49" x 2.24" and weighs about 0.34 lbs. The plastic closing cam is the part most prone to wear — after years of use it can flatten out or crack, losing the contoured shape that pulls the door the rest of the way closed. A worn cam or hinge typically shows up as a door that won't close fully on its own unless you push it firmly shut, or a door that feels loose, sags, or doesn't swing smoothly on its hinge. It directly replaces AP5656407, 2684526, PS5573850, W10249949, W10257197, and W10257209. Quick Answer The W10500004 Genuine OEM Whirlpool Refrigerator Bottom Door Hinge & Cam Kit (Right, Gray) fixes Whirlpool, Amana, KitchenAid, Maytag, Jenn-Air, Magic Chef, Roper, and Admiral refrigerators where the right-side fresh food door won't close on its own unless pushed firmly shut, or the door feels loose or sags on its hinge. Apollo Gray finish. Replaces AP5656407, 2684526, PS5573850, W10249949, W10257197, W10257209. Mounting the closing cam requires a new screw, sold separately — the kit does not include it. Common Problems This Part Fixes Refrigerator door won't close fully on its own — has to be pushed firmly shut Door that feels loose, sags, or doesn't swing smoothly on its hinge Worn or flattened closing cam that no longer pulls the door shut Visible cracks or wear on the plastic closing cam Door that doesn't seal properly due to incomplete closing Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator bottom door hinge and cam kit directly replaces the following OEM and cross-reference part numbers: 2684526, W10249949, W10257197, W10257209, AP5656407, AWP40907, EAP5573850, PD00024325, PS5573850 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This bottom door hinge and cam kit is compatible with select Whirlpool refrigerators, and also fits select Amana, KitchenAid, Maytag, Jenn-Air, Magic Chef, Roper, and Admiral refrigerators built on the Whirlpool platform, as well as select Kenmore Elite and Ikea refrigerators, including model numbers such as 3WSC19D4AY00, 3WSC19D4XW00, 3WSC19D4XD00, 3WSC19D4XB00, 3WSC20N4XB00, and 3WSC20N4XW00. Note — right side only: This kit is specific to the right-side fresh food door. A separate kit exists for the left side. This is also the lower door's hinge and cam kit — the upper door's closing cam is a different part sold separately. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hinge kit your refrigerator needs. Key Features Genuine Whirlpool OEM part — factory-specified hinge and cam design Combined kit — bottom hinge plus closing cam in one part Resolves "door won't close on its own," "door feels loose," and "worn or cracked cam" symptoms Apollo Gray finish Approximately 4.65" x 4.49" x 2.24", 0.34 lbs Direct drop-in replacement for the right-side lower door hinge and cam Replaces AP5656407, 2684526, PS5573850, W10249949, W10257197, and W10257209 Compatible with Whirlpool, Amana, KitchenAid, Maytag, Jenn-Air, Magic Chef, Roper, and Admiral refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10500004 Part Type Bottom Door Hinge & Closing Cam Kit Condition Genuine OEM Brand Whirlpool Door Position Right side, fresh food door, lower hinge Color Apollo Gray Dimensions 4.65" x 4.49" x 2.24" Weight 0.34 lbs Additional Hardware Needed New cam mounting screw (sold separately) Repair Difficulty Moderate — door removal required Quantity 1 hinge and cam kit Compatible Brands Whirlpool, Amana, KitchenAid, Maytag, Jenn-Air, Magic Chef, Roper, Admiral, Kenmore Elite, Ikea Installation Notes ⚠️ Unplug Refrigerator Before Starting — A New Cam Mounting Screw Is Required, Sold Separately Disconnect power at the outlet before beginning. Wear work gloves. Remove the top hinge cover, then remove the top hinge support to free the top of the door. Lift the door up and off the bottom hinge support to remove it completely — this is easier with a second person supporting the door's weight. Remove the old, worn closing cam and hinge from the bottom support. The manufacturer specifies that mounting the new closing cam requires a new screw, which is not included in this kit and must be ordered separately. Install the new W10500004 hinge and cam onto the bottom support, applying a small amount of lubricant such as petroleum jelly to the cam surface to help it move smoothly against the door once reassembled. Set the door back onto the bottom hinge support, making sure it seats correctly on the new cam. Reinstall the top hinge support and top hinge cover. Restore power and test the door by opening it partway and letting go — it should swing the rest of the way closed on its own if the cam is seated and lubricated correctly. Tools needed: 5/16" nut driver or socket, ratchet, small flat-blade screwdriver, work gloves. Frequently Asked Questions My door won't close all the way unless I push it. Is this the right part? Yes, this is the classic symptom of a worn closing cam. When the cam is new, its contoured shape gives the door that final "pull" to swing closed on its own once you've pushed it most of the way shut. As the cam wears flat or cracks over years of use, it loses that pulling action, leaving the door to stay open unless you close it firmly by hand. Do I need to buy anything else along with this kit? Yes — per Whirlpool's own specifications, mounting the new closing cam requires a new mounting screw, which is sold separately and not included in this kit. Order that screw at the same time to avoid a delay partway through the repair. Should I lubricate anything during installation? Yes, it's recommended. Applying a small amount of lubricant, such as petroleum jelly, to the cam surface helps it move smoothly against the door once everything is reassembled, and can extend the life of the new cam by reducing friction wear. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original hinge design, cam shape, and Apollo Gray finish of the bottom door hinge and cam kit originally installed on your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WD01X10393 Dishwasher Door Hinge Cable

Read more less

154756401 Genuine Frigidaire Dishwasher Door Hinge Cable The 154756401 is a Genuine OEM Frigidaire replacement dishwasher door hinge cable compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers. The door hinge cable runs through a pulley system at the base of the dishwasher door and is responsible for balancing and controlling the weight of the door as it opens and closes. When a cable breaks or frays, the door drops down suddenly and heavily, opening with a loud bang — or may not hold itself up at all, straining the door hinges and latch with every use. This is a Genuine OEM part manufactured by Frigidaire to factory specifications and directly replaces the older 154578801. It is sold as a single cable — most Frigidaire dishwashers have two door hinge cables (one on each side), and it is strongly recommended to replace both at the same time. Installs in under 30 minutes with basic hand tools. Quick Answer The 154756401 Genuine Frigidaire Dishwasher Door Hinge Cable fixes dishwashers where the door drops open too fast, bangs loudly when opened, doesn't stay open at a comfortable angle, or where a broken cable is visible at the door hinges. Sold individually — replace both cables at the same time. Compatible with Frigidaire, Electrolux, Kenmore, Crosley, and Ikea dishwashers. Replaces 154578801. Common Problems This Part Fixes Dishwasher door drops suddenly and forcefully when opened — "slams" down instead of lowering gently Loud banging or crashing noise when opening the dishwasher door Door does not stay open at a horizontal position — drops all the way down Broken, frayed, or snapped door cable visible near the door hinge or base of the door Door hinge is being damaged or strained due to missing cable tension Uneven door opening — one side drops faster than the other Replaces Part Numbers This door hinge cable directly replaces the following OEM and cross-reference part numbers: 154756401, 154578801, AFR14437, PD00082115, AP7212793, PS17217958. 154756401 is the current updated part number superseding the older 154578801. Contact our support team with your model number if you need compatibility confirmation before ordering. Compatibility This door hinge cable is compatible with select dishwashers from the following brands: Frigidaire dishwashers Electrolux dishwashers Kenmore / Sears dishwashers (Frigidaire/Electrolux-built models) Crosley dishwashers Gibson dishwashers Kelvinator dishwashers Westinghouse dishwashers Ikea dishwashers (select models) Important: Most Frigidaire dishwashers use two door hinge cables — one on each side. This part is sold as a single cable. It is strongly recommended to replace both cables at the same time, as the second cable is likely to fail soon after the first. Key Features Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance Balances and controls door weight as it opens and closes — prevents sudden door drops and hinge damage Works in conjunction with the door pulley and spring system to provide smooth, controlled door movement Current updated part number — directly supersedes 154578801 Sold individually — most models require two cables (one per side); replace both at the same time Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number 154756401 Supersedes 154578801 Part Type Dishwasher Door Hinge Cable Condition Genuine OEM Application Dishwashers Material Metal cable Sold As Single cable (most models require 2 — replace both at the same time) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, Ikea Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power before beginning any repair. Open the dishwasher door and remove the inner door panel by unscrewing the screws around the perimeter of the inner door. With the inner panel removed, locate the door hinge cable routing — the cable runs from a bracket near the bottom of the door, through a pulley, and connects to the door spring tension system at the base of the dishwasher. Note how the cable is routed before removing the old one. Remove the broken cable by detaching it from the anchor points at each end. Thread the new 154756401 cable through the same pulley path and re-attach it to the anchor points at both ends, ensuring proper tension. Reinstall the inner door panel. Close and open the door to verify it moves smoothly and holds itself open horizontally. Restore power and run a short cycle to confirm normal operation. Tip: Replace both cables at the same time — the second cable will likely fail soon after the first. Tools needed: Phillips screwdriver, Torx screwdriver (T20), needle-nose pliers. Frequently Asked Questions What does the dishwasher door hinge cable do? The door hinge cable is a tensioned metal cable that runs through a pulley and connects to the door spring system to balance the weight of the dishwasher door as it opens and closes. Without the cable, the full weight of the door would cause it to drop suddenly and forcefully when opened, slamming down onto the floor or straining the hinges with every use. The cable provides the controlled, counterbalanced movement that allows the door to lower gently and stay open at a horizontal position for easy loading and unloading. How many door cables does my Frigidaire dishwasher have? Most Frigidaire dishwashers use two door hinge cables — one on the left side and one on the right side of the door. This listing is for a single cable. When one cable breaks, the other is typically close behind since both cables have endured the same amount of use. It is strongly recommended to replace both cables at the same time while the door panel is already disassembled, saving you from repeating the repair shortly after. What is the difference between 154756401 and 154578801? These are the same door hinge cable. 154756401 is the current updated part number that superseded the older 154578801 during a production revision. If your dishwasher's parts diagram or old cable label shows 154578801, the 154756401 is the correct current replacement to order. Is this compatible with Electrolux and Kenmore dishwashers? Yes — Frigidaire and Electrolux are part of the same corporate family and share many components. The 154756401 cable is compatible with select Electrolux dishwashers and with Kenmore dishwashers built on the Frigidaire/Electrolux platform. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same door hinge cable installed in compatible Frigidaire, Electrolux, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout  

Read more less

2 Pack - XPARTCO 4933DD3001B Dishwasher Door Hinge Cable – Compatible with LG & Kenmore Dishwashers Product Description Restore smooth and controlled dishwasher door movement with the XPARTCO 4933DD3001B Dishwasher Door Hinge Cable. This high-quality aftermarket replacement connects the dishwasher door to the hinge spring system, allowing the door to open and close evenly without slamming or dropping. A worn or broken hinge cable can cause the door to fall open, feel too heavy, or fail to stay balanced. Replacing it with this durable XPARTCO cable helps restore proper door tension and safe operation. XPARTCO is a trusted aftermarket brand offering appliance replacement parts designed to meet OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers 4933DD3001B, 1395107, 4933DD3001A, PD00001803, EAP3524406, AH3524406, AP4511304, EA3524406, PS3524406   Compatibility This replacement dishwasher door hinge cable fits select LG and Kenmore (LG-manufactured) dishwashers. Example compatible models include (but are not limited to):LG LDF7811ST, LDF6920STKenmore 795.13293K701, 795.13299K701 Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit, length, and tension performance 🚪 Restores Proper Door Balance – Prevents door from dropping or slamming 💪 Durable Steel Cable – Designed to withstand repeated door cycles 💰 Cost-Effective Repair – Reliable alternative to OEM hinge cables 🛡️ Fixes Common Issues – Solves loose door, uneven opening, or excessive door weight 📐 Product Specification Part Number: 4933DD3001B Component Type: Dishwasher Door Hinge Cable Material: Braided steel cable with end fittings Application: Door hinge and spring tension system Installation Side: Typically used on left or right side (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Disconnect power to the dishwasher before servicing. Door springs are under tension—use caution during installation. Basic Steps: Disconnect dishwasher power. Remove the lower access panel. Carefully release tension from the old hinge cable. Remove the damaged cable from the hinge and spring. Install the new XPARTCO 4933DD3001B cable in the same routing. Reattach spring tension and reinstall access panel. Test door movement for smooth, balanced operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, controlled dishwasher door operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 4933DD3001B Dishwasher Door Hinge Cable – Compatible with LG & Kenmore Dishwashers Product Description Restore smooth and controlled dishwasher door movement with the XPARTCO 4933DD3001B Dishwasher Door Hinge Cable. This high-quality aftermarket replacement connects the dishwasher door to the hinge spring system, allowing the door to open and close evenly without slamming or dropping. A worn or broken hinge cable can cause the door to fall open, feel too heavy, or fail to stay balanced. Replacing it with this durable XPARTCO cable helps restore proper door tension and safe operation. XPARTCO is a trusted aftermarket brand offering appliance replacement parts designed to meet OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers 4933DD3001B, 1395107, 4933DD3001A, PD00001803, EAP3524406, AH3524406, AP4511304, EA3524406, PS3524406   Compatibility This replacement dishwasher door hinge cable fits select LG and Kenmore (LG-manufactured) dishwashers. Example compatible models include (but are not limited to):LG LDF7811ST, LDF6920STKenmore 795.13293K701, 795.13299K701 Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit, length, and tension performance 🚪 Restores Proper Door Balance – Prevents door from dropping or slamming 💪 Durable Steel Cable – Designed to withstand repeated door cycles 💰 Cost-Effective Repair – Reliable alternative to OEM hinge cables 🛡️ Fixes Common Issues – Solves loose door, uneven opening, or excessive door weight 📐 Product Specification Part Number: 4933DD3001B Component Type: Dishwasher Door Hinge Cable Material: Braided steel cable with end fittings Application: Door hinge and spring tension system Installation Side: Typically used on left or right side (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Disconnect power to the dishwasher before servicing. Door springs are under tension—use caution during installation. Basic Steps: Disconnect dishwasher power. Remove the lower access panel. Carefully release tension from the old hinge cable. Remove the damaged cable from the hinge and spring. Install the new XPARTCO 4933DD3001B cable in the same routing. Reattach spring tension and reinstall access panel. Test door movement for smooth, balanced operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, controlled dishwasher door operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

ERP 154578801 Dishwasher Door Hinge Cable Replaces Part Numbers: 154578801, 1196201, AH1524995, EA1524995, AP3958767, PS1524995.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WB15X27280 Genuine OEM GE Oven Door Handle and End Cap Assembly — Stainless Steel The WB15X27280 is a genuine GE OEM oven door handle and end cap assembly, finished in stainless steel, for GE ranges. This is the bar you grip every time you open or close the oven door, along with the two end caps that anchor it securely to the door frame. It's a simple mechanical part, but it takes a lot of repeated stress and impact over years of daily cooking, which is exactly why it's a common wear item. The handle measures 27.5 inches long. Over time, frequent use, exposure to high oven temperatures, and accidental impact can loosen, crack, or bend the handle or its end caps, making the door harder or less safe to operate. This is sold as a complete assembly — the handle bar and both end caps come together as one part and are not available individually, since the caps are what secure the handle to the door and the two are engineered as a matched set. It directly replaces AP6030812, WB15T10222, 4456008, and PS11762365. Quick Answer The WB15X27280 Genuine OEM GE Oven Door Handle and End Cap Assembly fixes GE, Hotpoint, RCA, and select Kenmore ranges with an oven door handle that's loose, cracked, wobbly, or has a broken or missing end cap. Stainless steel finish, 27.5" long. Replaces AP6030812, WB15T10222, 4456008, PS11762365. Sold only as a complete assembly — the handle and end caps are not available separately, even if only one end cap has failed. Common Problems This Part Fixes Oven door handle feels loose or wobbly when gripped Handle has cracked, bent, or broken End cap is cracked, broken, or missing entirely Handle has separated or come loose from the door frame Difficulty safely opening or closing the oven door Visible discoloration or heat damage on the handle or end caps Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven door handle and end cap assembly directly replaces the following OEM and cross-reference part numbers: WB15X27280, WB15T10222, AP6030812, AGE21582, 4456008, EAP11762365, PD00032591, PS11762365 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This handle and end cap assembly is compatible with select GE ranges, and also fits select Hotpoint, RCA, and Kenmore ranges built on the GE platform. Note — sold as a complete assembly only: The handle bar and end caps for this part are not sold separately, even if only one end cap or only one side has failed — you'll need to replace the complete WB15X27280 assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified fit, finish, and mounting Complete assembly — handle bar and both end caps included as a matched set Resolves "loose or wobbly handle," "cracked or broken handle," and "missing or broken end cap" symptoms Stainless steel finish for durability and a clean, matching appearance 27.5" handle length Direct drop-in replacement for the original door-mounted handle Replaces WB15T10222, AP6030812, 4456008, and PS11762365 Compatible with GE, Hotpoint, RCA, and select Kenmore ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB15X27280 Part Type Oven Door Handle and End Cap Assembly Condition Genuine OEM Brand GE Finish Stainless steel Handle Length 27.5 in. Kit Contents Handle bar + 2 end caps (sold as one assembly) Repair Difficulty Moderate — inner door panel removal required Quantity 1 handle and end cap assembly Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting — Support The Door While Working Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the oven door and locate the screws along the bottom edge of the door — typically four screws securing the inner door panel. Remove these screws, then carefully remove the inner door panel to expose the screws that hold the handle assembly in place from behind. Photograph the mounting hardware and orientation before removing the old handle. Remove the screws securing the old handle and end caps, and lift the assembly free. Position the new WB15X27280 assembly in the same orientation, secure it with the mounting screws, and reinstall the inner door panel with its bottom screws. Close and open the door a few times to confirm the handle feels solid with no wobble before returning the oven to normal use. Tools needed: Phillips or nut driver screwdriver, work gloves. Frequently Asked Questions Can I just replace one end cap instead of the whole handle? No. GE does not sell the end caps or the handle bar separately for this part — WB15X27280 is sold only as the complete assembly. Even if just one end cap has cracked or broken while the handle bar itself is fine, you'll need to order the full assembly to make the repair. How do I access the handle to replace it? Start at the bottom edge of the oven door, where you'll find screws (typically four) securing the inner door panel. Remove those screws and take off the inner panel, which exposes the screws holding the handle assembly in place from behind. From there, removing the old handle and installing the new one is straightforward. My handle is curved — can I get a flat one instead? This assembly is designed to match your oven's original handle shape and mounting points, so it replicates the curved profile if that's what your model originally came with. A differently shaped handle isn't offered as a substitute for this part number, since the end caps and mounting points are engineered specifically for the original handle's geometry. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original stainless steel finish, length, and mounting configuration of the handle and end cap assembly originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB13K21 Gas Oven Flat Igniter with Harness The XPARTCO WB13K21 is an aftermarket replacement flat-style gas oven igniter with harness compatible with select GE, Hotpoint, RCA, and Kenmore gas ranges and ovens. The oven igniter is a silicon carbide heating element mounted inside the oven next to the burner. It serves a dual purpose: it draws electrical current through the oven safety valve to hold it open, and it heats to ignition temperature to light the gas burner. The igniter must draw sufficient current — typically 3.2–3.6 amps — to hold the safety valve fully open. A weakened igniter that draws too little current will glow but never fully open the gas valve, preventing the burner from lighting. This flat-style igniter draws 3.4–3.6 amps at 115V. The ceramic block measures 1-1/2" L, with an overall bracket/cage measuring 3-3/4"L x 2-1/8"W x 13/16"H. The harness and plug extend approximately 7-7/8" from the igniter body with female pin connectors and a double wing mounting bracket. It can be used as a bake or broil igniter replacement on compatible models. It directly replaces WB13K21, WB13K12, WB13K13, WB13K14, WB13K0012, WB13K0013, WB13K0014, WB13K0021, WB13K10009, WB13K10026, IG21, 2494, AP2020569, AH231280, EA231280, EAP231280, PS231280, and PD00001023. Note: if the connector does not match your range's harness, cut the connector and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO WB13K21 Gas Oven Flat Igniter with Harness fixes GE, Hotpoint, RCA, and Kenmore gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat igniter, 3.4–3.6A, 115V. 1-1/2" ceramic block, 3-3/4"L x 2-1/8"W x 13/16"H bracket. 7-7/8" harness with female pins. If connector doesn't match, splice with porcelain wire nuts. Replaces WB13K21, WB13K12, WB13K13, WB13K14, IG21, AP2020569, AH231280, PS231280. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange but the gas burner never lights Oven takes more than 90 seconds to ignite after turning on Oven preheats very slowly — weak igniter no longer drawing enough current to fully open the gas valve Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: WB13K21, WB13K0012, WB13K0013, WB13K0014, WB13K10009, WB13K10026, WB13K12, WB13K13, WB13K14, 2494, AH231280, AP2020569, AGE21391, EA231280, EAP231280, PD00001023, PS231280. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands: GE gas ranges and ovens (select models) Hotpoint gas ranges and ovens (select models) RCA gas ranges and ovens (select models) Kenmore / Sears gas ranges (select GE-built models) Note: Can be used for both bake and broil igniter replacement on compatible models. If the two-pin connector does not match your range's existing harness connector, cut the connector off the new igniter and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner due to heat. Always verify your model number before ordering. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the safety valve to open it and allow gas to flow to the burner Draws 3.4–3.6 amps at 115V — correct amperage range to reliably open the GE oven gas safety valve Ceramic block: 1-1/2" L; bracket/cage: 3-3/4"L x 2-1/8"W x 13/16"H Harness and plug extend approximately 7-7/8" from the igniter body Female pin connectors with double wing mounting bracket — quick install on compatible models Can replace bake or broil igniter on compatible models If connector does not match: cut and splice using porcelain wire nuts (included) — never use standard plastic wire nuts near the burner Replaces over 18 older GE oven igniter cross-reference part numbers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPWB13K21 Part Type Gas Oven Flat Igniter with Harness (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (bake and broil) Igniter Style Flat (cageless silicon carbide element) Amperage Draw 3.4 – 3.6 Amps Voltage 115V AC Ceramic Block Length 1-1/2 inches Bracket / Cage Dimensions 3-3/4"L x 2-1/8"W x 13/16"H Harness / Lead Length Approximately 7-7/8 inches from igniter body Connector Type Female pins, two-pin quick-disconnect (splice with porcelain nuts if needed) Mounting Double wing bracket Material Silicon carbide / Ceramic / Metal / Plastic Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are secure. If you are not comfortable working on gas appliances, have this part installed by a qualified technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to skin oils. Do not touch the igniter element with bare hands — oils from skin will create hot spots that prematurely burn the igniter. Handle only by the bracket, harness, and mounting wings. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector at the connection point inside the oven. Remove the two screws securing the mounting bracket. If the new igniter's connector matches the harness, plug it in directly. If it does not match, cut the connector from the new igniter and use the included porcelain wire nuts to splice the wires to your range's existing harness — do not use plastic wire nuts. Mount the new igniter using the double wing bracket and two screws. Reinstall the oven bottom panel, restore gas and power, and run a bake cycle to confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, socket set, work gloves. Frequently Asked Questions My igniter glows but the burner never lights — is it the igniter? Yes, almost certainly. A gas oven igniter that glows orange or red but does not light the burner is a classic sign of a weakened igniter. The igniter must draw enough electrical current — typically 3.2 amps or more — to hold the gas safety valve fully open. As the silicon carbide element ages, its resistance increases and it draws progressively less current. When the current drops below the threshold needed to hold the valve open, the valve never fully opens, even though the igniter appears to glow. If the igniter glows for more than 90 seconds without lighting the burner, it needs to be replaced. Why can't I use plastic wire nuts to splice the igniter wires? The igniter is located inside the oven cavity, directly adjacent to the gas burner, where temperatures during operation can easily exceed what standard plastic wire nuts are rated for. Plastic wire nuts can melt or deform at oven operating temperatures, potentially exposing bare wire connections and creating a short circuit or fire hazard. Porcelain wire nuts are specifically rated for high-temperature applications and are the only safe connector to use when splicing igniter wires near the oven burner. Always use porcelain — never plastic — for any wiring connection inside the oven cavity. Can this igniter be used for both bake and broil? Yes — on compatible GE, Hotpoint, and Kenmore models, the WB13K21 can be used to replace both the bake igniter (lower burner) and the broil igniter (upper burner), as both igniters use the same part number and specifications on these models. Verify your range's parts diagram to confirm that both igniters use the WB13K21 before ordering for the broil position. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, it has weakened. You can also use a multimeter — disconnect the igniter wires and measure resistance. A working WB13K21-style igniter typically reads between 40 and 90 ohms at room temperature (a lower resistance draws more current; a very high resistance means the element is nearly failed). An open circuit (infinite resistance) means the element has burned through completely. If the igniter does not glow at all when the oven is turned on, it has completely failed electrically. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original WB13K21 oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less