Search results for "dishwasher element"

154825001 Genuine OEM Frigidaire Dishwasher Heating Element The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet. Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element. Common Problems This Part Fixes Dishes not getting properly clean because wash water isn't reaching the correct temperature Dishwasher not drying dishes — items come out wet at the end of the cycle Cycle taking noticeably longer than usual to complete Visible damage, corrosion, or discoloration on the element itself Element that doesn't glow or heat up when the wash cycle is running Water leaking near the high-temperature wire connector at the element terminals Mineral scale buildup visible on or around the element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: 154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD. Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers. Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration Exposed round design sits in the tub bottom for direct water heating and drying support Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure 0.98" mounting hole with two mounting nuts and wire terminals Two white alignment dots for correct positioning in the tub's retaining clips Direct drop-in replacement — no modification required Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 154825001 Part Type Dishwasher Round Heating Element (Exposed) Condition Genuine OEM Brand Frigidaire / Electrolux Location Bottom of the wash tub (exposed, visible) Mounting Hole 0.98 in. Terminals 2 wire connections + 2 mounting nuts Alignment 2 white dots must align with tub retaining clips Repair Difficulty Medium — basic dishwasher familiarity required Tools Required Screwdrivers, wrench set Quantity 1 heating element Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves. Frequently Asked Questions How do I know it's the heating element and not something else, like the control board? Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase. Can I clean the element instead of replacing it? Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point. I noticed water leaking near the element's wire connector. Is that related? Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring. Do I really need to pull the dishwasher out from under the counter? On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10518394 Genuine OEM Whirlpool Dishwasher Heating Element The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades. This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools. Quick Answer The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed. Common Problems This Part Fixes Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase Wash water not getting hot enough — poor cleaning performance even with proper detergent Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation Heated dry cycle not working — no warm air at the end of the cycle Element visibly burned through, broken, or showing arcing damage Multimeter continuity test on the element shows an open circuit (no continuity) Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element) Detergent not fully dissolving — water too cool to activate the formulation Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead. Compatibility This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including: Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram) Maytag dishwashers — select models (verify with parts diagram) KitchenAid dishwashers — select models Amana dishwashers — ADB1400AGW and related models Kenmore / Sears dishwashers — select Whirlpool-built models Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase Rated 1200W for efficient heating and reliable temperature control Oval-shape element approximately 15" L x 3" W x 3" H Mounts in the bottom of the dishwasher tub, secured underneath with large nuts Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times) Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070 Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10518394 Part Type Dishwasher Heating Element Condition Genuine OEM Application Dishwashers (Whirlpool platform) Shape Oval (NOT interchangeable with horseshoe-style elements) Wattage 1200W Dimensions Approximately 15" L x 3" W x 3" H Mounting Location Bottom of dishwasher tub Related Parts (Sold Separately) Rubber Washer (717273), Heater Nut (8268548) Post-Install Step Diagnostic reset required on most Whirlpool dishwashers Compatible Brands Whirlpool, Maytag, KitchenAid, Amana, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses. Frequently Asked Questions Why are my dishes coming out wet — is the heating element the cause? Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed. After installing the new element, the dishwasher still isn't heating — why? On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well. How is the W10518394 different from horseshoe-shape heating elements? The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher. Do I need to replace the rubber washers and nuts when installing this? Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle. Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Quick Answer The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle. Common Problems This Part Fixes Dishes in the lower rack not getting cleaned properly Reduced or uneven water coverage during the wash cycle Spray arm that won't rotate freely or gets stuck Visible cracks, warping, or damage on the arm itself Arm that has come loose or detached from the sump assembly Clogged nozzle holes reducing water pressure and spray coverage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers: 5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform. Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit Snaps directly into the bottom sump assembly for a secure, no-tools installation Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms Durable plastic and metal construction, gray/blue finish Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H) Direct drop-in replacement — no modification required Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5304517203 Part Type Dishwasher Lower Spray Arm Condition Genuine OEM Brand Frigidaire Location Bottom of the dishwasher tub, in the lower sump assembly Material Plastic and metal Color Gray / Blue Dimensions Approx. 16.00" x 3.10" x 3.10" (L x W x H) Repair Difficulty Very Easy — no tools required Quantity 1 lower spray arm Compatible Brands Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none. Frequently Asked Questions My dishes in the lower rack aren't getting clean. Is this the part I need? Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean. I've read that a spray arm can come loose during operation. How do I prevent that? This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed. Do I need any tools to replace this spray arm? No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 675813 Dishwasher Thermal Fuse The XPARTCO 675813 is an aftermarket replacement bimetal thermal fuse (TCO — thermal cut-off) kit compatible with a wide range of Whirlpool-family dishwashers including Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, and Admiral. The thermal fuse is a one-time safety device located on or near the control board that monitors internal temperature. If the dishwasher overheats — due to a blocked vent, malfunctioning heating element, or other fault — the fuse permanently interrupts power to protect the dishwasher and prevent fire hazards. Unlike a resettable thermostat, a blown thermal fuse must be replaced. Once it trips, the dishwasher will show no power and will not start. The kit includes one thermal cutoff fuse with a 2-wire harness (leads extending approximately 18 inches from the fuse), one zip tie, and installation instructions. The fuse body measures 1-1/16" L x 1" W x 7/16" H. The new wiring harness must always be used when replacing the fuse. Installs in 5–15 minutes with basic hand tools. Quick Answer The XPARTCO 675813 Dishwasher Thermal Fuse Kit fixes Whirlpool-family dishwashers that show no power, won't start, have a blank control panel, or stopped mid-cycle with no response. The thermal fuse permanently trips when the dishwasher overheats and must be replaced. Kit includes fuse with 2-wire harness, zip tie, and instructions. Fuse body 1-1/16" L x 1" W x 7/16" H. Always install using the new harness included. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, and more. Common Problems This Part Fixes Dishwasher completely dead — no power, no lights, no response when buttons are pressed Control panel blank with no indicator lights or display Dishwasher stopped mid-cycle and will not restart Dishwasher will not start despite the door being closed and latched No sounds when attempting to start the dishwasher Dishwasher behaves as if it has no power even though the outlet is live Replaces Part Numbers This dishwasher thermal fuse kit directly replaces the following OEM and cross-reference part numbers: 675813, 3375557, 3376359, 675813VP, 679723, AH382828, OEM9345567, AWP39651 PD00002439, EA382828, EAP382828, AP3115186, PS382828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse kit is compatible with select dishwashers from the following brands: Whirlpool dishwashers Kenmore / Sears dishwashers (Whirlpool-built models) KitchenAid dishwashers Maytag dishwashers Estate dishwashers Crosley dishwashers Inglis dishwashers Roper dishwashers Admiral dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bimetal thermal cut-off (TCO) fuse — permanently interrupts power if the dishwasher overheats, protecting against fire hazard One-time safety device — once tripped, the fuse must be replaced (it does not reset) Rated at 98°C — trips when internal temperature exceeds the safe operating limit Fuse body dimensions: 1-1/16" L x 1" W x 7/16" H; leads extend approximately 18" from fuse Kit includes thermal fuse with 2-wire harness, zip tie, and installation instructions Always install using the new harness included — never reuse the old harness Metal and plastic construction — reliable performance and heat resistance Direct replacement for 675813, 675813VP, 3375557, and 3376359 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 5–15 minutes with basic hand tools Product Specifications Part Number 675813 Part Type Dishwasher Thermal Fuse / Thermal Cut-Off (TCO) Kit Condition Aftermarket Replacement Fuse Type Bimetal thermal cut-off (one-time, non-resettable) Trip Temperature 98°C (208°F) Fuse Body Dimensions 1-1/16" L x 1" W x 7/16" H Lead Length Approximately 18 inches from fuse body Color White / Brown Material Metal / Plastic Kit Includes Thermal cutoff fuse with 2-wire harness, zip tie, instructions Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug or Switch Off Breaker Before Starting Unplug the dishwasher or turn off the circuit breaker before beginning any repair. The thermal fuse is located inside the dishwasher door panel near the control board. Open the dishwasher door and remove all screws from the inner door panel — a Torx bit is typically required on Whirlpool-family models. Carefully lift the inner door panel to expose the control board housing. Remove the black plastic cover over the control board to access the thermal fuse — it is typically on the right side of the board with one wire connected to each terminal. Test the old fuse with a multimeter for continuity (no continuity confirms the fuse has blown). Disconnect the old fuse and its harness. Connect the new 675813 fuse using the new 2-wire harness included in the kit — do not reuse the old harness. Secure the harness with the included zip tie. Reinstall the control board cover, inner door panel, and all screws. Restore power and run a test cycle. Note: If the fuse blows again after replacement, an underlying cause such as a blocked vent, failed heating element, or faulty control board should be diagnosed before replacing the fuse a second time. Tools needed: Torx screwdriver (T15 or T20), Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions What does the dishwasher thermal fuse do? The thermal fuse is a one-time safety device that monitors the internal temperature of the dishwasher. If the temperature rises above the safe operating limit — 98°C in this case — the fuse permanently interrupts the electrical circuit, cutting all power to the dishwasher. This protects both the appliance and your home from fire hazard caused by overheating. Unlike a resettable thermostat, a blown thermal fuse cannot be reset and must be physically replaced. How do I know if my thermal fuse has blown? The most obvious sign is a completely dead dishwasher — no lights, no sounds, and no response when you press any buttons, even though the outlet has power. You can confirm a blown fuse with a multimeter: disconnect the fuse from the harness and test for continuity across its two terminals. A working fuse will show continuity (near-zero resistance); a blown fuse will show no continuity (open circuit). If the fuse tests bad, replace it with the 675813 kit. Why did my thermal fuse blow, and will it happen again? Thermal fuses blow when the dishwasher overheats. Common causes include a blocked air vent, a malfunctioning or shorted heating element, a failed thermostat, or an electrical fault in the control board. If you simply replace the fuse without addressing the root cause, it may blow again. After replacing the fuse, run the dishwasher and monitor for any unusual heat, steam, or burning smell. If the fuse blows again, have the underlying fault diagnosed before ordering another replacement. Why must I use the new harness and not the old one? When a thermal fuse blows, the wiring harness connected to it may have been exposed to the same overheating event that tripped the fuse. The wires or connectors may have degraded or partially melted even if they appear intact. Using the old harness risks a poor connection or a recurring fault. Always install the new 2-wire harness included in the kit to ensure a reliable, safe connection. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, trip temperature, and performance of the original 675813 thermal fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

W11175771 Genuine OEM Whirlpool Dishwasher Water Valve The W11175771 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers, located behind the lower kick plate panel in either the right or left corner. This valve controls the flow of water into the appliance during the wash cycle — an electrical solenoid plunger opens and closes the valve to admit exactly the right amount of water at the appropriate stages of the dishwasher's cycle. Measuring approximately 3.37" in height, this is a superseding part, replacing the earlier W10872255 and W11130744 valve numbers so older models can be updated with the current version. Over time, a screen inside the valve can become clogged with sediment — this screen isn't designed to be cleaned or serviced, so a clog means the whole valve needs to be replaced. A failing valve produces a clear set of symptoms: the dishwasher not filling with enough water or not filling at all, leaking into the dishwasher while not in use, or overfilling with too much water. It directly replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743. Quick Answer The W11175771 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers that aren't filling with water, are leaking, or are overfilling. Located behind the lower kick plate panel. Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, W11130743. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter, since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with enough water, or not filling at all Water leaking into the dishwasher while it's not in use Dishwasher overfilling with too much water High-pitched whining sound while the dishwasher is filling Poor washing results or an error code related to water fill Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11175771, 3015468, 328C151-T, 4451572, 4843711, AP5804368, AP6024301, AP6339872, EAP11738107, EAP12578165, EAP3406951, AWP43823, PD00052484, PS11738107, PS12578165 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers built on the Whirlpool platform, including model numbers such as WDF130PAHB1, WDF130PAHB2, WDF130PAHS1, WDF130PAHS2, WDF130PAHW2, WDF330PAHB3, WDF330PAHW4, WDF331PAHB1, WDF520PADB9, WDF520PADM, WDT730PAHZ, WDT720PADM, WDF330PAHS, ADB1400AGW, KDTE104ESS1, and Kenmore 66513222N410 through N414. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher via an electrical solenoid plunger Resolves "won't fill," "leaking," "overfilling," and "whining noise" symptoms caused by valve failure Superseding part — current replacement for the earlier W10872255 and W11130744 valves Approximately 3.37" in height Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743 Compatible with Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11175771 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Behind the lower kick plate panel, right or left corner Height 3.37" Supersedes W10872255, W11130744 Screen Serviceable No — replace valve if clogged Repair Difficulty Easy to Moderate — approx. 15 to 30 minutes Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, Inglis Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the bottom front kick plate to access the interior, where the valve is located behind the panel in either the right or left corner depending on your model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water line, the electrical connector, and remove the mounting screws securing the old valve, then pull it free. Install the new W11175771 in the same position, securely reconnect the water line and electrical connector, and secure the mounting screws. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Reinstall the kick plate, restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Can I just clean the valve's screen instead of replacing the whole thing? No — the screen inside this valve isn't designed to be cleaned or serviced. If it becomes clogged with sediment from your household water supply, the entire valve should be replaced rather than attempting to clean or repair the screen itself. My dishwasher makes a high-pitched whining sound while filling. Is that this valve? Yes, this is a documented symptom of a failing water inlet valve. One customer specifically traced an "obnoxious high-pitched whining sound when filling with water" to this exact valve and resolved it with a straightforward replacement in about 15 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚰 DD82-01588A Dishwasher Water Inlet Valve – Genuine OEM Samsung Part 🔁 Replaces These Part Numbers DD82-01588A (primary OEM) Also Replaces PS12593084, AP6807545, DD81-02265A, AP6244375, PS12085633. Description: This Dishwasher Water Inlet Valve Assembly is essential for regulating the water flow into dishwasher, ensuring optimal cleaning performance. This replacement Genuine OEM part is engineered to provide precise water control, preventing leaks and maintaining efficient operation. ✅ Key Features Genuine Samsung OEM part – DD82-01588A Precision-engineered to match factory standards Controls cold water intake with accurate timing and pressure Easy to install using standard tools Tested for leak-free performance 🔧 Fixes Common Symptoms Dishwasher won’t fill or fills slowly Error codes related to water inlet No water intake at cycle start Valve leaks or hums without water flow 🚚 Why Buy from Parts‑O‑Matic? ✅ Genuine OEM quality — not a knock‑off ✅ Always Fast and Free U.S. shipping ✅ Expert customer support for part fitment ✅ Trusted by DIYers and appliance professionals 🛒 Restore proper water fill and cycle reliability — order your DD82-01588A OEM water inlet valve today from Parts‑O‑Matic and enjoy speedy, free delivery.

Read more less

W11047722 Genuine OEM Range Radiant Surface Element - Compatible with Whirlpool, KitchenAid, Maytag Product Description Restore your range’s cooking performance with the W11047722 Genuine OEM Range Radiant Surface Element. This Whirlpool-manufactured element is designed for select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and other compatible ranges. It provides even heat distribution for reliable cooking, addressing issues like uneven heating, no heat, or burnt-out elements. This single element is rated at 2500W and 240V, ensuring efficient operation for large to medium cookware. Note: Includes (1) radiant surface element. Disconnect power before installation. Verify compatibility with your range model. Replaces part numbers: W11047722, WP8273992, W10248262, 8273992, AP6041999, PS11775308, 316135401, 316224200, 316224201, 318198835, PD00044547, EAP11775308, FIX11775308, AH2361362, EA2361362, AP4416812, PS2361362.  Compatibility: Compatible with select range models, including but not limited to: Whirlpool: WFE525S0HV0, WFE525S0HZ0, WFE525S0JB0, WFE525S0JS0, WFE525S0JW0 KitchenAid: KSEG700EBS0, KSEG700ESS0, KSEG700EWH0 Maytag: MER6600FB0, MER6600FW0, MER6600FZ0 Jenn-Air: JEC3430BB00, JEC3430BS00 Amana: AER6603SFB0, AER6603SFS0, AER6603SFW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana ranges. 🔧 Specifications: 2500W, 240V, 9 3/4-inch radiant element, glass-ceramic construction. 💪 Reliable Performance: Delivers consistent heat for efficient cooking. 🛠️ Easy Installation: Requires screwdriver and gloves; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves uneven heating, no heat, or burnt-out element issues. Product Specification Part Number: W11047722 Component Type: Radiant surface element Material: Glass-ceramic with metal heating coil Dimensions: Approximately 9 3/4" diameter Electrical Specs: 2500W, 240V Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the range from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your range cooking efficiently today! Add to cart now for a reliable fix!

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC62-30314L Dishwasher Genuine OEM Water Valve 120V, 60Hz, single coil valve with GHT inlet.  Fits Specific Samsung Dishwashers Models. Replaces Part Numbers: DC62-30314L, AP5582579, PS4209101. Description: The Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This genuine OEM part ensures reliable water flow control, allowing your dishwasher to fill and drain effectively during each cycle. Designed specifically for Samsung dishwashers, it guarantees a perfect fit and seamless integration with your appliance.  

Read more less