Search results for "drum belt"

WP40111201 Genuine OEM Whirlpool Dryer Drum Belt The WP40111201 is a genuine Whirlpool OEM drum belt for full-size Whirlpool-built dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the tension (idler) pulley, and loops around the drive motor pulley. This belt is the sole mechanical connection between the motor and the drum — there is no gear or direct coupling — so when it breaks or slips off, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, but the drum sits still. Open the door and spin the drum by hand and it will turn freely with no resistance. This belt measures 93-3/8 inches long and 3/8 inch wide, with a 5-rib multi-groove profile. Belts fail from age and heat: the rubber hardens over years of thermal cycling, the ribs glaze over and begin slipping under a wet load, and eventually the belt cracks through or snaps outright. A screeching or squealing noise, a rhythmic thump timed to drum rotation, fraying at the edges, or black rubber dust in the cabinet are all signs a belt is near the end of its life. As a genuine OEM part, the WP40111201 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It directly replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549. Quick Answer The WP40111201 Genuine OEM Whirlpool Dryer Drum Belt fixes full-size Whirlpool-built dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer screeches, squeals, or thumps during operation. 93-3/8" long, 3/8" wide, 5-rib profile. Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549. Grooves face against the motor pulley on this platform — same orientation as our Y312959 belt. Common Problems This Part Fixes Dryer runs and hums but the drum does not turn — the classic broken belt symptom Drum spins freely by hand with no resistance when the door is open Loud screeching or squealing that begins as soon as the cycle starts Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt Grinding or rumbling from inside the cabinet as a frayed belt drags Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping Dryer won't start, or inadequate heating reported alongside a belt-related noise Black rubber dust or belt fragments found in the bottom of the cabinet Visible cracking, fraying, glazing, or stretching on the old belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, AWP47792, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115. 40111201 is the long-running legacy Whirlpool number and WP40111201 is the current part number carrying the "WP" prefix. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select full-size Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers Maytag dryers (select Whirlpool-built models) KitchenAid dryers (select models) Amana dryers (select models) JennAir dryers (select models) Kenmore dryers (select Whirlpool-built models, including SDG3606AWW) Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers (select models) This belt fits a large number of standard full-size front-load dryers used across North America. Because the compatible model list spans many years and revisions, always verify your full model number against your dryer's data label before ordering. Note: Whirlpool and Maytag use more than one length of drum belt across their dryer lineups, and belts of a similar rib count and width are not automatically interchangeable. This belt is 93-3/8" long — it is NOT the same belt as our 100"-long Y312959 belt used on other Maytag/Whirlpool platforms. A belt that's too long or too short for your drum will slip, walk off the pulley, or fail to seat properly. Measure your old belt or verify your model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, rib profile, and tension 93-3/8" length, 3/8" width, 5-rib multi-groove design Wraps around the drum, tension pulley, and drive motor pulley to transfer motor rotation to the drum Resolves "motor runs but drum won't turn," "screeching," "squealing," and "drum spins freely by hand" symptoms Multi-rib construction grips the motor pulley without slipping under heavy wet loads Direct drop-in replacement — no cutting, splicing, or modification required Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549 Compatible with Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP40111201 Part Type Dryer Drum Drive Belt Condition Genuine OEM Brand Whirlpool Length 93-3/8 in. Width 3/8 in. Ribs 5 Material Reinforced rubber Rib Orientation Grooves face against the motor pulley Routing Around drum → tension pulley → drive motor pulley Fuel Type Electric and gas dryers Quantity 1 belt Compatible Brands Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Pull off the lint trap and remove the screws securing the top panel, then raise the panel and support it with a block of wood. Remove the rear access panel to locate the motor, blower wheel, and belt. Photograph how the old belt routes around the drum, the tension pulley, and the motor pulley before removing anything — if the belt is already broken, note that the grooved side of this belt rides against the motor pulley, with the smooth back facing the drum. Loosen and remove the motor mount, lift the motor slightly, and slide the old belt free. The front panel typically needs to come off as well to fully access the drum. Vacuum out accumulated lint while the cabinet is open — lint buildup around the motor and idler is what cooks belts prematurely. Place the new belt around the drum, seat it in the polished wear track left by the old belt, then route it around the tension pulley and around the motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before repositioning the motor, so it doesn't slide off while you work. Re-secure the motor mount, then rotate the drum by hand several full turns and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the tension pulley and each drum roller by hand — if any is noisy, gritty, or has play, replace it now, since a seized pulley or worn roller will destroy the new belt quickly. Reassemble the front and rear panels and the top panel, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, 5/16" nut driver, flat-blade screwdriver, putty knife, masking tape, work gloves. Frequently Asked Questions How do I confirm the belt is broken and not the motor? With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright. What's the difference between WP40111201 and 40111201? They are the same belt across production revisions. 40111201 was the long-running legacy Whirlpool number and WP40111201 is the current number carrying the "WP" prefix Whirlpool adopted. WP40111201VP is a variant packaging code for the same belt. If your dryer's parts diagram or the old belt itself shows any of these numbers, this listing is the correct replacement. The remaining cross-references (14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549) are catalog identifiers used by various parts distributors for the same belt. Is this the same belt as your Y312959 listing? No. This belt is 93-3/8" long, while the Y312959 belt in our catalog is 100" long — the two are used on different Maytag/Whirlpool dryer platforms and are not interchangeable. Both share a similar 5-rib profile and grooves-against-motor-pulley orientation, which is exactly why they're easy to confuse. Always check your model number or measure your old belt's length before ordering either one. Which way do the grooves face on this belt? On this Whirlpool platform, the grooved (ribbed) side of the belt rides against the motor pulley, with the smooth back of the belt facing the drum. This is the same orientation as our Y312959 belt, but it is the opposite of some other manufacturers' platforms — for example, Frigidaire's 134719300 belt runs with the grooves facing down against the drum instead. Always confirm orientation for your specific brand and platform, and photograph the old belt before removing it whenever possible. The dryer squeals but the drum still turns. Belt or something else? Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry tension pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the tension pulley and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original 93-3/8" length, 3/8" width, and 5-rib profile of the drum belt originally installed in your Whirlpool, Maytag, KitchenAid, Amana, or related dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 134719300 Dryer Drum Belt The XPARTCO 134719300 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. The drum belt is a critical component that connects the motor pulley to the drum, enabling the drum to rotate during drying cycles. The belt wraps around the drum circumference, passes over an idler pulley (which maintains tension), and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail due to normal wear from friction and heat, cracking or fraying from age and repeated flexing, stretching that reduces tension and causes slipping, contamination from lint buildup, or sudden breakage from overloading or mechanical stress. Constructed from durable black rubber with reinforced fabric or cord embedded inside for strength and flexibility, designed to withstand thousands of hours of operation under high temperatures and constant friction. Dimensions: 90"L x 5/16"W x 1/8"H with 5 ribs and 4 grooves. It directly replaces 134719300, 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294. Important: install the belt with the grooves facing DOWN, against the drum. Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair since both wear together. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 134719300 Dryer Drum Belt fixes Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, the dryer makes loud squealing or squeaking noises, or clothes take too long to dry. 90"L x 5/16"W x 1/8"H. 5 ribs, 4 grooves. Black rubber. Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, PS2349294. Install with grooves facing DOWN against the drum. Often paired with idler pulley (134793500/134793511, sold separately). Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Dryer won't start — belt switch (on some models) tripped by broken belt Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — clear sign the belt has snapped Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 134719300, 137315300, 7134719300, AFR14405, AP4368788, EAP2349294, LB5300, PD00000843, PS2349294. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Frigidaire dryers (select electric and gas models) — including FDEB34RGS1/GS2, FDEB55RGS0/GS1, FDER436RHS0 and related models Electrolux dryers (select models) Crosley dryers — CDE4500KW0, CDE4700LB0/LW0, CDE4701QW0, CDE7300RW0, CDE7400QW0/QW1, CDE7500KB0/KR0/KW0, CDE7700LR0/LW0, CDEC450KW0, CDEC750KW0, CDG4500KW0, CDG4700LB0/LW0, CDG4701QW0, CDG7300RW0/RW1, CDG7400QW0, CDG7500KB0/KR0/KW0, CDG7700LW0/LW1 series Kenmore / Sears dryers — select Frigidaire/Electrolux-built models White-Westinghouse dryers (select models) Gibson dryers (select models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler pulley (134793500 or 134793511, sold separately) — it wears from the same friction cycles as the belt, and if it's rough, seized, or noisy, the new belt will wear out prematurely. Many customers replace both together as a matched set. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction with reinforced fabric/cord for strength and flexibility Engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 90" L x 5/16" W x 1/8" H with 5 ribs and 4 grooves Install with grooves facing DOWN against the drum for proper engagement Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294 Compatible with Frigidaire, Electrolux, Crosley (CDE/CDG series), Kenmore, White-Westinghouse, and Gibson dryers Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP134719300 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Frigidaire/Electrolux platform) Length 90" Width 5/16" Thickness 1/8" Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber with reinforced fabric/cord Installation Orientation Grooves face DOWN against the drum Often Paired With Idler Pulley (134793500 or 134793511, sold separately) Compatible Brands Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, Gibson Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooves Face DOWN Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Remove the top and/or front panels of the dryer to access the drum — the specific procedure varies by model, but typically involves removing 2–4 screws under the top edge or lint trap area, then lifting or tilting the top panel forward. Once the top is off, disconnect the door switch wire harness and lift the front panel free. This exposes the drum, motor, and idler pulley. Photograph the belt routing before disassembly if any belt fragments remain — you'll need to match the routing pattern with the new belt. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley. Support the drum from underneath (a wooden block or two can help hold it in position). Route the new 134719300 belt around the drum in the same position as the old belt — approximately 4-6 inches from the front lip of the drum. Install with the grooves facing DOWN, against the drum surface — this is essential for proper engagement with the motor pulley. From under the drum, route the belt over the idler pulley and around the drive motor pulley in a Z-shape. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly. Verify the drum rotates freely without binding — if it doesn't, the belt is twisted, kinked, or misrouted; fix it before reassembling. Reinstall the front and top panels, reconnect the door switch, restore power, and run a test cycle to confirm normal operation. Tools needed: Phillips screwdriver, wooden block, side cutters (for removing broken belt fragments), flathead screwdriver, work gloves. Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming/whirring) but the drum stays still, the belt has almost always snapped or is slipping badly. To confirm without opening the dryer: reach in through the door and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum bearings or rollers could be the issue. In either case, opening the dryer to inspect the belt visually is the definitive check — a snapped belt will be lying in the bottom of the cabinet. Why do I have to install the belt with grooves facing down? The dryer's motor pulley is a smooth, un-grooved cylinder — the belt runs against it with the flat (smooth) side. The drum, on the other hand, needs the grooves to positively engage and drive without slipping under load. So the grooved side faces the drum (down when you're routing the belt around the drum from above), and the smooth side wraps around the motor pulley and idler pulley. Installing the belt backwards with grooves facing up will cause the belt to slip against the drum immediately and can burn out the new belt within a few minutes of operation. Should I replace the idler pulley at the same time? Yes, it's strongly recommended. The idler pulley (134793500 or 134793511 on many compatible dryers) maintains constant tension on the drum belt as the drum rotates. It wears from the same friction cycles as the belt — when the belt fails, the idler pulley bearings have typically also been stressed and are near end-of-life. Since the dryer is already open and the pulley is right there next to the belt, replacing both saves you a repeat repair when the pulley fails a few months later. Signs of a worn idler pulley: rough or noisy rotation when spun by hand, visible wear grooves, or seized bearings. What's the difference between 134719300 and 137315300? These are the same drive belt across production revisions. 137315300 was a Frigidaire OEM part number and 134719300 is the current cross-referenced part number that covers the same belt. Both are physically and functionally identical — if your dryer's parts diagram shows either number, this listing is the correct replacement. LB5300 and 7134719300 are additional catalog references for the same belt. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable rubber with reinforced fabric/cord to match the dimensions (90"L x 5/16"W x 1/8"H), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original 134719300 drum belt used in compatible Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WE03X32037 Dryer Drum Belt Replaces WE12M24 The XPARTCO WE03X32037 is an aftermarket replacement drum drive belt for GE, Hotpoint, and RCA portable, compact, and unitized stack dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the idler tension pulley, and finishes around the small drive motor pulley. That belt is the only mechanical link between the motor and the drum — there are no gears and no direct coupling — so when it breaks, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, and the drum simply sits there. Open the door and spin the drum by hand and it coasts freely with no resistance at all. This belt measures approximately 79 inches long and about 1/4 inch wide, with a 4-rib multi-groove profile molded into the inner face. The 79" length is the defining specification here — GE uses several visually similar 4-rib dryer belts across its lineup, and the difference between them is length. Belts fail from heat and age: the rubber hardens, the ribs glaze and begin slipping under a heavy wet load, and eventually the belt cracks through or snaps. Fraying edges, a squeal at startup, a rhythmic thump timed to drum rotation, or black rubber dust in the bottom of the cabinet all point to a belt nearing the end of its life. It directly replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, and related numbers. Installs in 45–90 minutes with basic hand tools. Quick Answer The XPARTCO WE03X32037 Dryer Drum Belt fixes GE, Hotpoint, and RCA portable, compact, and stack dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, thumps, or rumbles during a cycle. Approximately 79" long, 1/4" wide, 4 ribs, black rubber. Fits DDP1370/DDP1375/DDP1380 portable and DSKP333/DSKS333/DSKS433 stack models. Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943. Not the same belt as the 89-1/2" full-size GE WE12M29 — length is what separates them. Common Problems This Part Fixes Dryer runs and hums but the drum does not turn — the classic broken belt symptom Drum spins freely by hand with no resistance when the door is open Loud squealing or screeching that begins as soon as the cycle starts Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt Grinding or rumbling from inside the cabinet as a frayed belt drags Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping Clothes not drying because the drum isn't tumbling to expose them to airflow Black rubber dust or belt fragments in the bottom of the cabinet Visible cracking, fraying, glazing, or stretching on the old belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WE03X32037, WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, PS16729246, EAP16729246, AH755943, EA755943, 943874, AGE25647, PD00074729 WE03X32037 is the current GE part number; WE12M24 is the long-running legacy number that most service diagrams and older belts still carry. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select portable, compact, and unitized stack dryers from the following brands: GE portable and compact electric dryers — DDP1370, DDP1375, and DDP1380 series GE unitized stack and Spacemaker laundry centers — DSKP333, DSKS333, and DSKS433 series Hotpoint compact and stack dryers (select GE-built models) RCA compact and stack dryers (select GE-built models) Select Kenmore compact dryers built on the GE platform Verified model numbers include: DDP1370GAM, DDP1370SAM, DDP1370SBM, DDP1375GAM, DDP1375GBM, DDP1375GCM, DDP1375GDM, DDP1375GEM, DDP1375SAM, DDP1375SBM, DDP1380GAM, DDP1380GBM, DDP1380GCM, DDP1380GDM, DDP1380GFM, DDP1380SAM, DDP1380SBM, DDP1380SCM, DDP1380SDM, DDP1380TAM, DSKP333EC0WH, DSKP333EC0WW, DSKP333EC2WW, DSKP333EC3WW, DSKP333EC4WW, DSKP333EC5WW, DSKP333EC6WW, DSKS333EC0WH, DSKS333EC0WW, DSKS333EC2WW, DSKS333EC3WW, DSKS333EC4WW, DSKS333EC5WW, DSKS333EC6WW, DSKS433EA0AA, DSKS433EB3WW, DSKS433EB5WW, DSKS433EB6WW, and DSKS433EB7WW. Note — 79" portable/compact belt only: GE uses several visually identical 4-rib dryer belts that differ only in length, and they are NOT interchangeable. This belt is approximately 79 inches, for portable, compact, and stack units. It is NOT the WE12M29 / WE03X29897 belt (89-1/2") used on full-size GE dryers, NOT the WE12X10009 belt (87"), and NOT the WE12X10014 / WE12X42 belt (87-13/16"). Fitting a longer belt leaves slack the idler cannot take up, and the belt will slip or walk off the pulley within minutes. Measure your old belt end to end, or verify your full model number, before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum drive belt — transfers motor rotation to the dryer drum Approximately 79" long, the correct length for GE portable, compact, and unitized stack dryers 4-rib multi-groove profile molded into the inner face for positive grip on the motor pulley 1/4" width matched to the original belt track and idler pulley Durable black rubber construction that resists heat hardening and cracking Resolves "motor runs but drum won't turn," "squealing," "thumping," and "drum spins freely by hand" symptoms Multi-rib design prevents slipping under heavy wet loads where a worn belt would stall Direct drop-in replacement — no cutting, splicing, or modification required Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, AH755943, EA755943, and 943874 Compatible with GE, Hotpoint, RCA, and select Kenmore compact and stack dryers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number XPWE03X32037 OEM Part Number WE03X32037 (formerly WE12M24) Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application GE Portable, Compact, and Unitized Stack Dryers Length Approx. 79 in. Width 1/4 in. Ribs 4 ribs / 3 grooves Material Rubber Color Black Rib Orientation Ribbed side faces the drum Routing Around drum → idler tension pulley → drive motor pulley Fuel Type Electric and gas dryers Quantity 1 belt Compatible Brands GE, Hotpoint, RCA, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — the sheet metal edges inside the cabinet are sharp. Before removing anything, photograph how the old belt routes around the drum, around the idler tension pulley, and around the motor pulley. If the belt is already broken and the routing isn't visible, note that the ribbed side of the belt faces toward the drum, with the smooth back riding against the idler pulley. Access on these compact and stack units is generally from the front: remove the top panel, then the control panel and front panel, which frees the drum enough to lift or tilt it forward. Vacuum out accumulated lint while the cabinet is open — restricted airflow and lint packed around the motor are what cook belts prematurely. Slip the new belt around the drum roughly one-third of the way back from the front lip, ribbed side against the drum, and seat it in the polished wear track the old belt left behind. Reach underneath, route the belt around the idler pulley, then loop it around the small motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before you reach underneath, so it can't slide off while you work the idler into position. Many GE idler arms have a locked or pre-loaded position — if yours does, remember to release it after the belt is seated, or the belt will have no tension and the drum will stall under load. Once routed, rotate the drum several full turns by hand and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the idler pulley and each drum roller by hand; if any is noisy, gritty, or has side-to-side play, replace it now, because a seized idler or flat-spotted roller will destroy the new belt quickly. Reassemble, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, nut driver or socket set, putty knife, masking tape, flashlight, work gloves. Frequently Asked Questions How do I confirm the belt is broken and not the motor? With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright. What's the difference between WE03X32037 and WE12M24? They are the same belt across production revisions. WE12M24 was the long-running legacy GE number and WE03X32037 is the current number that supersedes it. If your dryer's parts diagram or the old belt itself shows WE12M24, WE12M9, WE12X79, or WE12X0079, this listing is the correct replacement. The remaining cross-references (AP3418890, AP7186820, PS755943, AH755943, EA755943, 943874) are catalog identifiers used by various parts distributors for the same belt. Can I use a longer GE belt if this one is out of stock? No. GE's 4-rib dryer belts look nearly identical and differ mainly in length, which is precisely why they get substituted by mistake. This belt is about 79"; the full-size GE belt WE12M29 is 89-1/2", and WE12X10009 and WE12X10014 are around 87". On a compact or portable drum, that extra 8 to 10 inches is far more slack than the idler arm can absorb, so the belt runs loose, slips on the motor pulley, and typically walks off within minutes. If you're unsure, lay your old belt flat in a loop and measure its circumference before ordering. Which way do the ribs face? On this GE platform the ribbed side faces toward the drum, so the ribs grip the drum surface while the smooth back of the belt rides against the idler pulley. This is worth stating plainly because rib orientation is not universal across manufacturers — some other platforms run the grooves against the motor pulley instead. Whenever possible, photograph the old belt before removing it. The polished wear track on the drum will also show you exactly where the belt is meant to sit. The dryer squeals but the drum still turns. Belt or something else? Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry idler pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the idler and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice. Why did my belt fail in the first place? Usually heat and age — rubber hardens over years of thermal cycling until it cracks. Two things accelerate it sharply. Restricted airflow from a lint-clogged vent makes the whole cabinet run far hotter than designed, which cooks the belt. And a seized idler pulley or a flat-spotted drum roller forces the belt to drag against a stationary surface, shredding it in short order. If your belt failed unusually early, clean the vent ducting end to end and inspect the idler and rollers rather than assuming the new belt will simply last longer. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (approximately 79" length, 1/4" width), 4-rib profile, rubber construction, and drum-drive function of the original WE03X32037 / WE12M24 belt used in compatible GE, Hotpoint, RCA, and related portable, compact, and unitized stack dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W10849499 Dryer Drum Belt The XPARTCO W10849499 is an aftermarket replacement drum belt for Whirlpool's large-capacity dryer platform. The belt wraps all the way around the outside of the drum, passes around the idler tension pulley, and loops around the drive motor pulley — that belt is the only mechanical connection between the motor and the drum, so when it breaks, the console still lights up, the motor still hums, and the blower still moves air, but the drum sits completely still. Open the door and spin the drum by hand and it will turn freely with no resistance. This belt measures approximately 97.75 inches long. Belts fail from age and heat: the rubber hardens over years of thermal cycling, the ribs glaze over and begin slipping under a heavy wet load, and eventually the belt cracks through or snaps outright. A worn or seized idler pulley is also a common root cause of premature belt failure, since a pulley that won't turn freely forces the belt to drag continuously against a stationary surface until it shreds. Squealing or chirping at startup, a rhythmic thump timed to drum rotation, fraying at the edges, or black rubber dust in the cabinet are all signs a belt is near the end of its life. As an aftermarket replacement, the W10849499 is built to OEM-equivalent quality standards. It directly replaces AP5989682, 4383705, PS11731121, and W10610882. Quick Answer The XPARTCO W10849499 Dryer Drum Belt fixes Whirlpool large-capacity dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, chirps, or thumps during operation. Approximately 97.75" long. Replaces AP5989682, 4383705, PS11731121, W10610882. If your belt broke due to a worn idler pulley rather than simple age, replace the pulley (PS334244) at the same time or the new belt will wear out quickly too. Common Problems This Part Fixes Dryer runs and hums but the drum does not turn — the classic broken belt symptom Drum spins freely by hand with no resistance when the door is open Loud squealing, chirping, or scraping noise from inside the dryer Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping Clothes not drying completely, or drying taking longer than it used to Broken belt pieces or fragments found inside the drum Visible cracking, fraying, glazing, or stretching on the old belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: W10849499, W10610882, AP5989682, 4383705, AWP42591, EAP11731121, OEM17969055, PD00046442, PS11731121 W10610882 was the immediately preceding number for this same belt. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select large-capacity Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool large-capacity electric and gas dryers Maytag dryers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana dryers (select models) Magic Chef, Admiral, Norge, Roper, and Inglis dryers (select models) Select Kenmore and Ikea dryers built on the Whirlpool platform Verified model numbers include: YWED8500DC, YWED8000DW, YWED8500DW, 7MWGD8000E, and 7MWGD8500E. Note: Whirlpool uses several different drum belt lengths across its dryer lineup, and this one is approximately 97.75" long — different from the shorter belts used on other Whirlpool-built platforms. Belts of a similar rib profile but a different length are not interchangeable; a belt that's too long or short for your drum will slip, walk off the pulley, or fail to seat properly. Verify your model number, or measure your old belt end to end, before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum belt for Whirlpool's large-capacity dryer platform Approximately 97.75" in length Wraps around the drum, idler tension pulley, and drive motor pulley to transfer motor rotation to the drum Resolves "motor runs but drum won't turn," "squealing or chirping," and "drum spins freely by hand" symptoms Direct drop-in replacement — no cutting, splicing, or modification required Replaces W10610882, AP5989682, 4383705, and PS11731121 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore large-capacity dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10849499 OEM Part Number W10849499 (formerly W10610882) Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Whirlpool Large-Capacity Dryers Length Approx. 97.75 in. Routing Around drum → idler tension pulley → drive motor pulley Fuel Type Electric and gas dryers Companion Part Idler pulley PS334244 (check/replace if belt failed prematurely) Quantity 1 belt Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — A Second Person Helps Support The Drum Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. On many large-capacity models, both the front and rear panels need to come off to fully access the belt and drum, so budget extra time compared to a simpler platform. Photograph how the old belt routes around the drum, the idler pulley, and the motor pulley before removing anything. Loosen and remove the motor mount or bracket as needed to slip the old belt free, and check the idler pulley by spinning it with your fingers — if it's stiff, gritty, or doesn't spin freely, replace it at the same time, since a worn pulley is a common cause of premature belt failure and will shorten the life of the new belt. With the front panel off, the drum may need to be supported by hand as it comes free — having a second person hold the drum steady makes this significantly easier and reduces the risk of scratching the drum or dropping it. Vacuum out accumulated lint while the cabinet is open. Place the new belt around the drum, seat it in the polished wear track left by the old belt, then route it around the idler pulley and around the motor pulley. Reinstall the motor mount, rotate the drum by hand to confirm the belt tracks straight and stays centered, then reassemble the front and rear panels. Restore power and run a short empty cycle listening for squeal or thump before loading it. Tools needed: nut driver or bit driver, open-end wrench, Phillips screwdriver, work gloves, and ideally a second person to support the drum. Frequently Asked Questions How do I confirm the belt is broken and not the motor? With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. My belt broke and I noticed the idler pulley felt stiff. Do I need to replace that too? Yes, strongly consider it. A worn or seized idler pulley is a well-documented cause of belt failure — if the pulley can't spin freely, it drags against the belt continuously instead of rolling with it, which wears through even a brand-new belt quickly. If your old belt broke and the pulley feels stiff, gritty, or doesn't spin smoothly when you turn it by hand, replace the idler pulley (part PS334244) along with the belt to avoid repeating this repair soon. Is this the same length as your other Whirlpool dryer belt listings? Not necessarily — Whirlpool uses different belt lengths across different dryer platforms even when the rib profile looks similar. This belt is approximately 97.75" long, which is specific to the large-capacity platform it's designed for. Always check your model number or measure your old belt's total length before ordering, since a belt of the wrong length will not seat and tension correctly. Why does replacing this belt need two people? On this large-capacity platform, accessing the belt often means removing the front panel and freeing the drum, which is heavy and can be awkward to support single-handedly while also working with your other hand. A second person holding the drum steady while you route the new belt reduces the risk of the drum shifting, scratching the finish, or being dropped. It's not strictly required, but it makes the job considerably easier. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the approximately 97.75" length and rib profile of the original W10849499 / W10610882 belt used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, and related large-capacity dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Y312959 Dryer Drum Belt Replaces WPY312959 The XPARTCO Y312959 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers — including the long-running vintage Maytag DE and DG halo-of-heat series. The drum belt is a critical component that connects the drive motor to the drum. It wraps all the way around the drum's circumference, passes around a spring-loaded idler (tension) pulley, and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail from normal wear, cracking or fraying from age and repeated flexing, exposure to heat and lint buildup, stretching that causes slipping, or sudden breakage. Constructed from durable black rubber. Dimensions: 100" long x 3/8" (5/16") wide, with 5 ribs and 4 grooves. Includes instructions. It directly replaces Y312959, WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PD00028571, and PS11757542. Important: install the belt with the grooved side against the motor pulley and the smooth side against the drum. Because the belt is symmetrical, it can be installed with either end facing out. Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO Y312959 Dryer Drum Belt fixes Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, or the dryer makes loud squealing/thumping noises. 100"L x 3/8"W. 5 ribs, 4 grooves. Black rubber. Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PS11757542. Install grooved side against the motor pulley, smooth side against the drum. Often paired with idler pulley WP6-3037050 and drum roller kit 12001541. Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — a clear sign the belt has snapped Belt worn thin or stretched after decades of use on a vintage Maytag dryer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: Y312959, WPY312959, 1000H5, 1246110, 3-12959, 3-14774, 312959, 314774, 8195-959, P46-150, P46-151, 6 3129590, AP6024192, AWP51437, EAP11757542, PD00028571, PS11757542 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Maytag electric dryers — DE106, DE107, DE110, DE180, DE18CA/CM/CS/CT, DE19CA/CD/CS/CT, DE210, DE212, DE21CA/CM/CS/CT, DE22CA/CS/CT, DE23CD, DE24CA/CM/CS/CT, DE25CS, DE26CA/CD/CS/CT, DE27CA/CS/CT, DE303, DE308, DE309, DE312, DE313, DE382, DE4000, DE408-DE9900 series and many more Maytag gas dryers — DG106, DG107, DG110, DG18CA/CM/CS/CT, DG19CA/CD/CS/CT, DG210, DG212, DG21CA/CM/CS/CT, DG22CA/CS and related DG-series models Maytag dryers — LDE and LDG series (LDE7304ACE, LDE8406ACE/ACM/ADE, LDE8410, LDG8424AAE, LDG9304AAM and related) Jenn-Air dryers (select models) Whirlpool dryers (select Whirlpool-built models) Amana, Magic Chef, Admiral, Norge, Roper dryers (select Whirlpool/Maytag-built models) Kenmore / Sears dryers (select Whirlpool/Maytag-built models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler (tension) pulley (WP6-3037050) and the drum support rollers (kit 12001541 / 303373K) — they wear from the same friction cycles as the belt, and if they're rough, seized, or noisy, the new belt will wear out prematurely. Before replacing the belt due to noise, check the drum support rollers and idler pulley and replace if you see signs of wear. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction — engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 100" long x 3/8" (5/16") wide with 5 ribs and 4 grooves Install with the grooved side against the motor pulley and the smooth side against the drum Symmetrical design — can be installed with either end facing out Includes instructions Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, and PS11757542 Compatible with vintage Maytag DE/DG series, LDE/LDG series, plus Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number Y312959 OEM Part Number WPY312959 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Maytag / Whirlpool platform) Length 100" Width 3/8" (5/16") Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber Installation Orientation Grooved side against motor pulley, smooth side against drum Often Paired With Idler Pulley (WP6-3037050), Drum Roller Kit (12001541 / 303373K) Compatible Brands Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooved Side Against Motor Pulley Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Access the drum by removing the appropriate panels — the specific procedure varies by model, but on many vintage Maytag dryers this involves removing the front or top panel. Photograph the belt routing before disassembly if any belt fragments remain. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley, and vacuum out accumulated lint and belt dust. Clean any belt dust off the drum. Route the new Y312959 belt around the drum. Install with the grooved (ribbed) side against the motor pulley and the smooth side against the drum — this is the correct orientation for proper drive engagement. Because the belt is symmetrical, either end can face outward. A helpful tip from experienced installers: use two small pieces of tape to hold the belt against the drum while you lace it onto the idler and motor pulleys. From under or behind the drum, route the belt around the idler (tension) pulley and the drive motor pulley following the belt diagram for your model. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly without binding. While you have the machine apart, check that the idler pulley and drum support rollers spin freely — if they're rough or noisy, replace them now to protect the new belt. Reassemble the panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, vacuum, work gloves, tape (helpful for holding the belt). Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming) but the drum stays still, the belt has almost always snapped. To confirm without opening the dryer: reach in and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum rollers or bearings could be the issue. Opening the dryer to inspect is the definitive check — a snapped belt will be lying in the bottom of the cabinet. On decades-old Maytag dryers, a belt that finally snapped from age is one of the most common repairs. Which way does the belt go — grooves in or out? Install the belt with the grooved (ribbed) side facing the motor pulley and the smooth side against the drum. The ribs engage the grooved motor pulley for positive drive without slipping, while the smooth side rides against the large drum surface. Note that this is the opposite orientation from some other dryer belts (like certain Frigidaire belts where grooves face the drum) — so don't assume; follow the grooves-against-motor-pulley rule for this Maytag/Whirlpool-platform belt. The belt is symmetrical end-to-end, so either end can face outward; only the grooved-vs-smooth orientation matters. Should I replace the idler pulley and drum rollers at the same time? It's strongly recommended, especially on older dryers. The idler (tension) pulley (WP6-3037050) keeps the belt under proper tension, and the drum support rollers (kit 12001541 / 303373K) carry the drum's weight as it turns. All wear from the same friction and heat cycles as the belt. In fact, a common piece of repair advice is: before you replace the belt due to noise, check the drum support rollers and idler pulley first — worn rollers or a seized idler are frequent noise sources, and if you replace only the belt, the new belt may wear out prematurely against a bad pulley. Since the dryer is already apart, replacing all three together is efficient and saves a repeat repair. What's the difference between Y312959 and WPY312959? These are the same drum belt across production revisions. Y312959 was the earlier Maytag part number and WPY312959 is the Whirlpool-era part number (after Whirlpool acquired Maytag) for the same belt. WPY312959VP is a variant packaging code. All are physically and functionally identical — if your dryer's parts diagram shows any of these numbers, this listing is the correct replacement. The many other cross-references (3-12959, 314774, LB234, P46-150, etc.) reflect the belt's long production history across decades of Maytag dryers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag/Whirlpool OEM part, but is manufactured from durable rubber to match the dimensions (100"L x 3/8"W), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original Y312959/WPY312959 drum belt used in compatible Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE03X29897 Dryer Drum Belt Product Title XPARTCO WE03X29897 Dryer Drum Belt - Compatible with GE, Hotpoint, Kenmore Dryers Product Description Ensure your dryer tumbles smoothly with the XPARTCO WE03X29897 Dryer Drum Belt from Parts-O-Matic. This high-quality aftermarket belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum for efficient drying. Compatible with select GE, Hotpoint, RCA, and Kenmore dryers, this belt resolves issues like failure to tumble, squealing or thumping noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select GE, Hotpoint, RCA, and Kenmore dryer models. 🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying. 💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair. 🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production. Compatibility: Compatible with models including but not limited to: GE: GTD33EASK0WW, GTD42EASJ2WW, GTD65EBSJ0WS, GTX33EASK0WW Hotpoint: HTX21EASK0WW, HTX24EASK0WS Kenmore: 363.61542412, 363.71542410 Replaces part numbers: WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, PS16542496. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension (e.g., WE12X83). Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Caution: Avoid stretching the belt during installation, as this can reduce its lifespan. Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

W11568627 Genuine OEM Dryer Drum Belt - Compatible with Whirlpool, Maytag, Kenmore Product Description Restore your dryer’s tumbling action with the W11568627 Genuine OEM Dryer Drum Belt. This Whirlpool-manufactured belt is designed for select Whirlpool, Maytag, Kenmore, and other compatible dryers. It connects the motor to the drum, ensuring smooth rotation during the drying cycle. This part addresses issues like the drum not spinning, unusual noises (e.g., squeaking or thumping), or the dryer stopping mid-cycle, often caused by a worn, stretched, or broken belt. Note: Includes (1) dryer drum belt. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: W11568627, W10577771, PD00070745, EAP16660508, AP7175918, PS16660508. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WED5010LW0, WED4950EW0, WED4950EW1, WED4950EW2, WED4950EW3 Maytag: MED4950DW0, MED4950DW1, MED4950DW2, MED4950DW3 Kenmore: 110.67022610, 110.67022611, 110.67022612, 110.67022613 Amana: NED4950EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, and other dryers. 💪 Reliable Performance: Ensures smooth drum rotation for consistent drying. 🛠️ Easy Installation: Requires screwdriver, pliers; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves drum not spinning, squeaking noises, or mid-cycle stopping. Product Specification Part Number: W11568627 Component Type: Dryer drum belt Material: Rubber Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO 6602-001655 Dryer Drum Belt The XPARTCO 6602-001655 is an aftermarket replacement dryer drum belt compatible with select Samsung and Kenmore dryers. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from premium neoprene rubber reinforced with polyester cords, this 5-rib belt measures 92 inches long x 5/16 inch wide and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It is a direct drop-in replacement for OEM part numbers 6602-001655 and 6602-001314, and installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 6602-001655 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer during operation. It drives the drum via the motor and idler pulleys. Compatible with select Samsung and Kenmore dryers. Measures 92" L x 5/16" W with 5 ribs and 4 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Samsung dryers (gas and electric) Kenmore / Sears dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92" length x 5/16" width — 5-rib, 4-groove design for a secure, slip-free grip on the pulleys Made from premium neoprene rubber with polyester cord reinforcement — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 6602-001655 and 6602-001314 — no modification required Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (DC93-00634A) and drum rollers (DC97-16782A) for a complete drum drive repair Product Specifications Part Number 6602-001655 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 5/16 inch Height 1/8 inch Ribs 5 ribs, 4 grooves Material Neoprene rubber with polyester cord reinforcement Color Black Compatible Brands Samsung, Kenmore Often Replaced With DC93-00634A Idler Pulley, DC97-16782A Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum belt, remove the top panel and front panel of the dryer. Lift the drum out of the cabinet, remove the old belt, and loop the new 6602-001655 belt around the drum with the ribbed side facing inward. Route the belt slack around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific video for the correct belt path around the pulleys. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the drum is out, this is an ideal time to also inspect and replace the idler pulley and drum support rollers if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Will the 6602-001655 fit my Samsung or Kenmore dryer? This belt is compatible with select Samsung and Kenmore dryers. Use the model search above to verify your model number, or contact our support team before ordering. What does the dryer drum belt do? The drum belt wraps around the outside of the dryer drum and connects to the motor pulley and idler pulley. As the motor spins, it drives the belt which causes the drum to rotate, tumbling your clothes through the heated air to dry them. A broken or worn belt means the drum cannot spin. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor runs and you can hear it humming, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is slipping or partially broken. Opening the dryer cabinet and visually inspecting the belt will confirm if it is broken, frayed, or stretched. Should I replace the idler pulley and drum rollers at the same time? Yes — since you need to disassemble the dryer to replace the belt anyway, it is highly recommended to also inspect and replace the idler pulley (DC93-00634A) and drum support rollers (DC97-16782A) at the same time. These parts wear at a similar rate and replacing all three together prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from premium neoprene rubber with polyester cord reinforcement to match the dimensions and performance of the original belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less