Search results for "dryer igniters and gas valves"

Genuine OEM 279311 Dryer Igniter Kit and Bracket The Genuine OEM Whirlpool 279311 is the gas dryer igniter kit with mounting bracket. The silicon carbide igniter glows to light the gas burner and produce the heat that dries your clothes. When the igniter weakens or breaks, the dryer tumbles but doesn't heat, because the gas valve never gets the signal to light the burner. This is the original Whirlpool part. It is listed as a replacement for both round and flat igniters, so it covers a long list of older Whirlpool part numbers for gas dryers sold as Whirlpool, Kenmore, Maytag, and KitchenAid. Quick Answer The Genuine OEM 279311 Igniter Kit and Bracket fixes a gas dryer that spins but doesn't heat because the igniter has burned out or is too weak to open the gas valve. It is for gas dryers only. Classic symptom: the drum turns and the dryer sounds normal, but clothes come out cold and damp, and you never see the igniter glow. Common Problems This Part Fixes Gas dryer runs but doesn't heat Clothes come out damp after a full cycle Igniter never glows, or glows but the burner never lights Cracked, broken, or burned igniter Burner lights unreliably or only some of the time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This igniter kit directly replaces the following part numbers: 279311, 239233, 239300, 239302, 26000279311, 279185, 279311VP, 338899, 338900, 3389895, 340607, 3415, 343128, 41-311, 6-85211, 660991, 685211, 686590, 687399, 691039, 8113, 99912719, AH334180, DE351, DE354, DE363, K35-166, AP3094138, AWP39784, EAP334180, EA334180, PD00002344, PS334180 These numbers span several generations of Whirlpool's own part numbering for this igniter as dryer models were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This igniter kit is for Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers, including these examples: Whirlpool LGN1000HQ0, LGN1000HQ1, 7MWG66740SG0, 7MWGD72HEDW0 Maytag 7MMGDC300YW0, 7MMGDC410AW0 Kenmore 11097291110, 10687884100, 110279119, 1103401771 Note: This igniter is for gas dryers only. The models above are a sample, not a full list. One supplier lists the kit contents as a 3-inch flat igniter, mounting bracket, 4-inch wire lead and plug. Confirm your model number and the igniter style against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool gas dryer igniter kit with bracket Silicon carbide igniter that lights the gas burner Listed to replace both round and flat igniters Resolves no-heat problems caused by a failed igniter Fits Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers Product Specifications Part Number 279311 OEM Part Number 279311 Part Type Gas Dryer Igniter Kit with Bracket Condition Genuine OEM Fuel Type Gas Dryers Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power and Shut Off the Gas Unplug the dryer and close the gas shutoff valve before beginning, and wear work gloves. Remove the panel that gives access to the burner assembly per your model's service guide, disconnect the igniter's wire connector, and remove the old igniter and bracket. The igniter is fragile, so handle it by the bracket and avoid bumping or squeezing the element. Install the new kit in the same position, reconnect the wires, then restore the gas and power and test the dryer for heat. If you smell gas at any point, stop, ventilate, and call your gas utility. Frequently Asked Questions My gas dryer spins but doesn't heat. Is this the part I need? A failed igniter is a common cause. If you run the dryer and never see the igniter glow, or it glows but the burner doesn't light, test the igniter for continuity. A bad coil on the gas valve or a thermal fuse can cause the same symptom, so check those too. Will this fit an electric dryer? No. This igniter is for gas dryers only. Electric dryers use a heating element instead. Why did my new igniter break? Silicon carbide igniters are fragile. Handle the new one by the bracket, and don't press or bump the element during installation. A weak or restricted gas supply or a faulty gas valve can also make igniters fail early. Will this fit my dryer? It is listed for many Whirlpool-built gas dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE4X750 Gas Dryer Igniter The XPARTCO WE4X750 is an aftermarket replacement flat igniter for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers, replacing GE part WE4X750 and cross-referencing 5303937186 and 4391996. The igniter sits in the burner assembly. It heats up when electrical current passes through it and lights the gas so the dryer can heat. When it wears out or stops glowing, the dryer may run but not heat. Check your model number before ordering, as gas dryers use several different igniters. Quick Answer The XPARTCO WE4X750 Gas Dryer Igniter replaces a worn or non-glowing igniter on a compatible gas dryer from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands. Replaces WE4X750, WE04X0750, 5303937186 and 4391996. Classic symptom: the dryer runs but does not heat, and the igniter doesn't glow. Other parts can cause the same symptom. Common Problems This Part Fixes Gas dryer not heating Igniter not glowing Worn igniter that no longer lights the burner Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer igniter directly replaces the following part numbers: WE4X750, WE04X0750, 276846, AGE25807, AH268196, AP2042796, EA268196, PD00001123, PS268196, 5303937186, 08001685, 08010845, 08015456, 1036069, 3281151, 5303281151, 8001685, F000134211, F134211-000, F134211000, F139743-000, F139743000, G139743-000, AFR17339, AH900236, AP3674313, EA900236, PD00000539, PS900236, Q000622141, Q622141, WQ622141, 4391996, 14211282, 3-4970, 3018, 304970, 41-311, 41-590, 4391996VP, AH373025, AP3109449, AWP39344, DE351, DE363, EA373025, K35-166, K35-455, PD00002514, PS373025 Gas dryers use several different igniters, and they are not interchangeable by number alone. If your old igniter shows a different number, contact our support team and we'll check whether it matches. Compatibility This igniter is listed for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers. Example GE and Hotpoint models that use WE4X750: GE DBL333GA0CC, DCL333GA0AA, DVL223GA0WW, DBL333GY0WW GE DCB330GB0KC, DCD330GY1AC, DH43GW0WW Hotpoint NVL333GY0AA Note: The models above are a small sample of the roughly 36 that retailers list for WE4X750, not a full list, and the example models are GE and Hotpoint. For other brands, confirm fit by your igniter's part number (such as 4391996 or 5303937186) and your model. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WE4X750 flat gas dryer igniter Lights the gas burner so the dryer can heat Installs in the dryer burner assembly Replaces the earlier GE number WE04X0750 and cross-references 5303937186 and 4391996 Product Specifications Part Number XPWE4X750 OEM Part Number WE4X750, 5303937186, 4391996 Part Type Gas Dryer Igniter (Flat) Condition Aftermarket Replacement Quantity 1 Igniter Application Select GE, Hotpoint, Whirlpool, Maytag, Frigidaire & Other Gas Dryers Installation Notes ⚠️ Disconnect Power And Shut Off The Gas Before Installing Unplug the dryer and shut off the gas supply before you begin, and wear work gloves. Remove the panel to reach the burner assembly, note how the igniter and its wiring connect, and remove the old igniter. Handle the new igniter carefully and install it in the same position. Reconnect the wiring, restore power and gas, and test the dryer. If you smell gas at any point, stop and contact a qualified technician. Frequently Asked Questions My gas dryer runs but doesn't heat. Is this the part I need? It can be, if the igniter has worn out and no longer glows. Other parts, such as the gas valve coils or thermal fuse, can cause the same symptom, so confirm the igniter is the problem before replacing it. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WE4X750. If you specifically need a genuine GE part, contact our support team. Can I use a different gas dryer igniter? Not by number alone. Gas dryers use several different igniters. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my dryer? It is listed for select gas dryers from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE4X444 Gas Dryer Genuine Igniter Replaces Part Numbers:WE4X444, WE04X0444, WE11X0096, WE4X444R, AH268028, EA268028, OEM8170538, AP2042634, PS268028, WP4392003, 4392003, 14200046, 3-3376, 303376, 41-982, 4392003BULK, 55438, 55438-6, 63-5010, 63-5877, DE350, K35-106, K35-368, R0611505, OEM24037398, AP6009349, PS11742507. Description: This Gas Dryer Igniter is a replacement part for specific GE, Hotpoint, Whirlpool dryer models. This essential component is responsible for igniting the gas in the burner, allowing the dryer to heat up and effectively dry your clothes. The igniter heats up to a high temperature to ignite the gas, starting the heating process necessary for drying.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XP382 Dryer Gas Valve Solenoid for DC62-00201A The XP382 is an aftermarket replacement gas valve solenoid coil kit for Samsung gas dryers, and also fits select Whirlpool, Sears, and Kenmore models using a compatible two-coil gas valve. This is a newer-style coil kit that fits most dryers using a two-coil gas valve design, and it works alongside the gas valve assembly (DC62-00201A) to regulate the precise amount of gas needed to properly combust and generate heat for drying clothes. Over time, these solenoid coils can weaken or fail electrically, preventing the gas valve from opening correctly even when the igniter is functioning normally. Symptoms of a failing gas valve solenoid include the burner not igniting even though the igniter glows, weak or inconsistent heat, or the dryer running a full cycle with little to no heat. Quick Answer The XP382 Dryer Gas Valve Solenoid fixes Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve, where the burner isn't igniting despite the igniter glowing, heat is weak or inconsistent, or the dryer runs without heating. Fits Samsung DC62-00201A gas valve assembly. This is a gas ignition component — always shut off the gas supply and let the dryer cool before working on it, and if you smell gas at any point, stop and call a professional. Common Problems This Part Fixes Burner not igniting even though the igniter glows normally Weak or inconsistent heat Dryer running a full cycle with little to no heat Gas valve failing to open when the igniter calls for gas Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer gas valve solenoid directly replaces the following OEM and cross-reference part numbers: Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This gas valve solenoid is compatible with select Samsung gas dryers using the DC62-00201A gas valve assembly, and also fits select Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve design. Note: This is a coil kit that works with the gas valve assembly, not a replacement for the full valve body itself. If your gas valve assembly needs full replacement rather than just the coils, you'll need the complete DC62-00201A assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dryer needs. Key Features Aftermarket replacement gas valve solenoid coil kit Resolves "burner won't ignite," "weak heat," and "no heat" symptoms tied to gas valve solenoid failure Newer-style coil kit fitting most two-coil gas valve designs Direct drop-in replacement matching the original mounting and connection Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A Compatible with Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil valve Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP382 OEM Part Number DC62-00201A (compatible coil kit) Part Type Dryer Gas Valve Solenoid Coil Kit Condition Aftermarket Replacement Coil Configuration Two-coil Application Gas Dryers Repair Difficulty Moderate — gas appliance component Quantity 1 solenoid coil kit Compatible Brands Samsung, Whirlpool, Sears, Kenmore Installation Notes ⚠️ Shut Off Gas Supply And Unplug Dryer Before Starting This is a gas ignition component. Turn off the gas supply to the dryer at the shutoff valve and disconnect power at the outlet before beginning. Allow the dryer to cool fully if it has recently been in use. Wear work gloves. If you smell gas at any point during this repair, stop immediately, do not operate any switches, leave the area, and contact your gas utility or a qualified technician from a safe location. Access the gas valve assembly, typically located near the burner housing — consult your dryer's service documentation for the exact access point on your model. Locate the old solenoid coils and disconnect their wiring. Remove the mounting screws or clips securing the old coils to the valve body and pull them free. Install the new XP382 coils in the same position, reconnect the wiring fully, and secure the mounting hardware. Restore the gas supply and power, then test the burner to confirm it ignites reliably with consistent heat. If you are not fully comfortable working with gas line connections, have a qualified technician perform this repair instead. Frequently Asked Questions My igniter glows but the burner doesn't light. Is this the part I need? Yes, this is a classic sign of a failed gas valve solenoid. The igniter can glow and reach ignition temperature normally, but if the solenoid coils that open the gas valve have failed electrically, no gas reaches the burner to actually ignite, leaving the dryer to run without heat. Do I need the whole gas valve assembly, or just this coil kit? If the valve body itself is intact and only the solenoid coils have failed, this coil kit is the more targeted and typically less expensive repair. If the valve body is cracked, stuck, or otherwise physically damaged, you'll need the complete DC62-00201A gas valve assembly instead. Is it safe to replace this myself? This repair involves working around your dryer's gas supply line, so take care to fully shut off the gas and let the appliance cool before starting. If you're not comfortable working around gas appliances, or if you smell gas at any point, stop and contact a qualified technician or your gas utility rather than continuing the repair yourself. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the coil configuration and connection type needed to work with the DC62-00201A gas valve assembly used in compatible Samsung, Whirlpool, Sears, and Kenmore gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11590294 Gas Oven Igniter The XPARTCO W11590294 is an aftermarket replacement flat-style silicon carbide gas oven igniter compatible with select Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges in the WFG, AGR, VRGW, and related series. The oven igniter is a silicon carbide heating element mounted next to the oven burner tube. When a bake or broil cycle is started, the igniter draws electrical current through the gas safety valve, which holds the valve open — and simultaneously heats to ignition temperature to light the gas. The igniter must draw at least 3.2 amps to hold the gas valve fully open; as the silicon carbide element ages and weakens, it draws progressively less current, causing the oven to take too long to light, not light at all, or glow without ever opening the gas valve. This flat-style igniter is rated 3.3–3.6 amps at 120V and measures approximately 4" wide x 1" high. It features a silicon carbide element, high-temperature ceramic housing, and metal bracket. The current part number W11590294 directly supersedes W11208965, W11613927, and W11506321 — all four are the same igniter across successive production revisions. It also replaces 4977065, AP7193166, PS16744629, and EAP16744629. Pre-attached wire connectors included. Note: do not touch the silicon carbide element with bare hands — skin oils cause premature burnout. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W11590294 Gas Oven Igniter fixes Whirlpool-family gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat silicon carbide igniter, 3.3–3.6A, 120V, approx. 4"W x 1"H. Do not touch element with bare hands. Replaces W11208965, W11613927, W11506321, 4977065, AP7193166, PS16744629. Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and more. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange or red but the oven burner never lights Oven takes more than 90 seconds to ignite — igniter too weak to fully open the gas valve Oven preheats very slowly — weakened igniter limiting gas valve opening Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11590294, W11208965, W11506321, W11613927, AP7193166, AWP45526, EAP16744629, PD00083398, PS16744629. W11590294 is the current production part number superseding W11208965, W11613927, and W11506321 — all four are the same igniter. If your parts diagram shows any of these numbers, this replacement is correct. Contact our support team with your model number if you need confirmation before ordering. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands and series: Whirlpool gas ranges — WFG320 series (WFG320M0MB0, WFG320M0MS0, WFG320M0MW0 and related models) Whirlpool gas ranges — WFG505 series (WFG505M0BS4, WFG505M0BW3, WFG505M0MB0, WFG505M0MS0, WFG505M0MW0 and related models) Amana gas ranges — AGR4203 series (AGR4203MNB0, AGR4203MNW0 and related models) Amana gas ranges — AGR6303 series (AGR6303MMB0, AGR6303MMW0 and related models) Crosley gas ranges — VRGW series (VRGW3150RB0, VRGW3150RW0, VRGW3162RB0, VRGW3162RS0, VRGW3162RW0 and related models) Maytag gas ranges (select models) KitchenAid gas ranges (select models) Jenn-Air gas ranges (select models) Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the gas safety valve to hold it open so gas can flow to the burner Draws 3.3–3.6 amps at 120V — correct amperage range to reliably open the oven gas safety valve on compatible models Dimensions: approximately 4" wide x 1" high Silicon carbide element, high-temperature ceramic housing, metal mounting bracket Pre-attached wire connectors included — direct plug-in installation on compatible models Current production part superseding W11208965, W11613927, and W11506321 Do not touch the silicon carbide element with bare hands — skin oils cause premature burnout Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and related brands Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPW11590294 Supersedes W11208965, W11613927, W11506321 Part Type Gas Oven Flat Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Igniter Style Flat silicon carbide element Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Dimensions Approximately 4" W x 1" H Material Silicon carbide / Ceramic / Metal / Plastic Color White / Silver Connector Pre-attached wire connectors Handling Note Do not touch element — skin oils cause premature burnout Compatible Brands Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas range. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. ⚠️ Handle With Care — Do Not Touch the Igniter Element The silicon carbide igniter element is fragile and sensitive to skin oils. Handle only by the bracket and wiring — never touch the silicon carbide element itself. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel to expose the burner assembly. Locate the old igniter mounted next to the oven burner tube. Disconnect the igniter's wire connectors and remove the two mounting screws securing the bracket. Note the wire routing inside the range cavity before removing — be careful not to let the burner wires fall back into the range body. Connect the new W11590294 igniter's pre-attached connectors to the matching wires from the range. Mount the new igniter in the same position with the two bracket screws. Reinstall the oven bottom panel and racks. Restore gas and power, then run a bake cycle and confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the relationship between W11590294, W11208965, W11613927, and W11506321? These are all part numbers for the same gas oven igniter across successive production revisions by Whirlpool. W11506321 was an earlier version, W11613927 and W11208965 were subsequent updates, and W11590294 is the current production number. All four are the same flat silicon carbide igniter with the same specifications, dimensions, and function. If your range's parts diagram or old igniter shows any of these numbers, this replacement covers all of them. My oven igniter glows but the burner never lights — is this the right part? Yes — an igniter that glows but fails to light the burner is the most common symptom of a weakened igniter. The gas safety valve requires at least 3.2 amps of current draw through the igniter to hold it open. As the silicon carbide element ages, it draws less current — eventually reaching a point where it glows visibly but no longer draws enough current to fully open the gas valve. If the igniter glows for more than 90 seconds without the burner lighting, it needs replacement. The W11590294 is rated 3.3–3.6 amps, which is the correct range to reliably activate the safety valve on compatible models. What is the difference between W11590294 and W11176454? Both are flat silicon carbide oven igniters for Whirlpool-family gas ranges, but for different model series. The W11590294 is used on the WFG320, WFG505, and related entry-level Whirlpool and Amana gas ranges. The W11176454 (which replaces W10914411) is used on higher-end Whirlpool, Amana, and Maytag models across a broader range of WFG, MGR, and related series. They have the same amperage rating and igniter style but are not always interchangeable — always verify your model number before ordering to confirm which igniter is correct for your range. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, the igniter is too weak. For a more precise test, use a multimeter in resistance mode — disconnect the igniter and measure resistance across the element. A working W11590294-style igniter typically reads between 40–100 ohms at room temperature. An open circuit (infinite resistance) means the element has burned through completely. You can also test in operation by measuring current draw at the igniter circuit — a reading below 3.2 amps indicates the igniter is too weak to reliably open the gas valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original W11590294 gas oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO MEE61841401 Gas Oven Igniter The XPARTCO MEE61841401 is an aftermarket replacement oven burner igniter compatible with select LG and Kenmore gas ranges in the LDG, LRG, LSG, LSS, LTG, and LSR series. The igniter is a flat glow bar hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without ever lighting the burner. This igniter draws 3.3–3.8 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F within approximately 60 seconds. The igniter body measures 3-1/2 inches long x 1-3/4 inches wide x 7/8 inches high, with a lead/plug assembly extending approximately 10-3/4 inches from the igniter. It includes a 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors to accommodate direct plug-in or spliced installation. Directly replaces OEM part numbers MEE61841401, MEE61841403, and MEE63084901. Quick Answer The XPARTCO MEE61841401 Gas Oven Igniter fixes LG and Kenmore gas ovens that won't heat, take too long to preheat, display error codes F9 or F11, or have an igniter that glows but never lights the burner. Flat glow bar style, silicon carbide. Draws 3.3–3.8A at 120V. Igniter body 3-1/2" L x 1-3/4" W x 7/8" H with 10-3/4" lead. Includes bracket and 2 porcelain wire connectors. Replaces MEE61841403 and MEE63084901. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat Igniter glows orange or red but never lights the gas burner Error codes F9 or F11 displayed on LG gas ranges Gas smell when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Igniter burned out or visibly cracked or broken Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: MEE61841401, MEE63084901, 1599783, MEE61841403, EAP3535362, ALG1385007, PD00001851, 095225468650, AH3535362, EA3535362, AP5214765, PS3535362. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands and series: LG gas ranges — LRG series (freestanding) LG gas ranges — LDG series (freestanding) LG gas ranges — LSG series (slide-in) LG gas ranges — LSS series LG gas ranges — LTG series LG gas ranges — LSR series Kenmore / Sears gas ranges (select LG-built models) Compatible with both single and double oven models. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Flat glow bar hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance, high melting point, corrosion and oxidation resistant Draws 3.3–3.8 amps at 120V AC — correct amperage range to open the LG gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 60-second heat-up time Igniter body: 3-1/2" L x 1-3/4" W x 7/8" H; lead/plug assembly: approximately 10-3/4" from igniter body Plug-in installation — includes 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors for splicing if needed Compatible with single and double oven models Directly replaces MEE61841401, MEE61841403, and MEE63084901 — no modification required in most cases Resolves error codes F9 and F11 on compatible LG gas ranges Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with basic hand tools Product Specifications Part Number MEE61841401 Also Replaces MEE61841403, MEE63084901 Part Type Gas Oven Burner Igniter (Flat Glow Bar Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (single and double oven) Igniter Style Flat glow bar, cageless Material Silicon Carbide / Metal / Ceramic / Porcelain / Plastic Colors White / Black / Gray Amperage Draw 3.3 – 3.8 Amps Voltage 120V AC Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 60 seconds Igniter Body Dimensions 3-1/2" L x 1-3/4" W x 7/8" H Lead / Plug Length Approximately 10-3/4 inches from igniter body Includes Igniter, mounting bracket, 2-wire harness/plug, 2 porcelain wire connectors Error Codes Resolved F9, F11 Compatible Brands LG, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to contamination. Do not touch the ceramic bar with bare hands under any circumstances — oils from skin will damage the element and significantly shorten its lifespan. Handle only by the bracket, wires, and plug. To install: unplug the range and shut off the gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector. Secure the new MEE61841401 igniter to the burner bracket with the mounting screws. If the plug is a direct match to your range's harness, plug it in. If not, cut the wires and use the included porcelain wire connectors to splice the new igniter to the existing wiring. Reinstall the oven bottom panel, restore gas supply and power, and run a test cycle. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between MEE61841401, MEE61841403, and MEE63084901? These are all part numbers for the same LG flat glow bar oven igniter used across different model ranges and production runs. MEE63084901 is the earlier part number; MEE61841401 and MEE61841403 are updated versions. All three are interchangeable, and this aftermarket replacement is compatible with all of them. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than normal to preheat, or the igniter glowing orange but never lighting the gas burner. A healthy igniter glows bright orange and ignites the burner within about 60 seconds. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Error codes F9 or F11 on LG ranges can also indicate a failed igniter. Do I need to splice the wires or does it plug straight in? This igniter includes a 2-wire harness/plug for direct plug-in installation on most compatible LG models. If the connector does not match your range's existing harness, cut the old connector off and use the 2 porcelain wire connectors included in the kit to splice the new igniter to the existing wiring. Do not use standard plastic wire nuts — only porcelain connectors should be used near the oven burner due to the high heat involved. What do error codes F9 and F11 mean on an LG range? On compatible LG gas ranges, error code F9 typically indicates an oven heating failure, and F11 can indicate a shorted or failed igniter circuit. Both codes can be triggered by a weak or failed oven igniter. Replacing the MEE61841401 igniter resolves these error codes in many cases — though other causes such as a failed gas safety valve or control board issue should also be ruled out if the problem persists after replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from silicon carbide, metal, ceramic, and porcelain to match the electrical specifications and physical dimensions of the original MEE61841401 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 316489403 Gas Oven Igniter The XPARTCO 316489403 is an aftermarket replacement gas oven igniter compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges, ovens, and stoves. The oven igniter is the component that lights the gas burner — when you set the oven to bake or broil, electricity flows through the igniter, heating it until it glows bright orange. This heat both ignites the gas and draws enough current to open the gas safety valve, releasing gas to the burner. When the igniter weakens with age, it may still glow but no longer pull enough current to open the safety valve — so the oven fails to light, takes a long time to heat, or heats unevenly. This is a flat-style, open-cage igniter. Electrical rating: 3.2–3.6 amps, 120V AC. Made of silicon carbide and ceramic for high heat resistance and long service life. Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; the lead and plug measure approximately 16" long. Includes the flat-style igniter assembly with bracket and leads/plug. It directly replaces 316489403, 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063. Important: the igniter element is fragile — handle it only by the bracket, never by the element itself. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 316489403 Gas Oven Igniter fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ovens that won't light, take too long to heat, heat unevenly, or where you smell gas because the igniter is too weak to open the safety valve. Flat-style open-cage igniter. 3.2–3.6A, 120V AC. Silicon carbide/ceramic. Overall 3-1/2"L x 1-3/4"W x 13/16"H, 16" lead. Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, PS2364063. Handle by the bracket only — the element is fragile. Common Problems This Part Fixes Oven won't light or heat at all — igniter too weak to open the gas safety valve Oven takes a long time to reach temperature — igniter glowing but drawing insufficient current Oven heats unevenly or undercooks food — weak or slow ignition Igniter glows but the burner never ignites — classic sign of a degraded igniter Igniter doesn't glow at all — burned out or open circuit (no power reaching the burner) Gas smell when the safety valve opens but the burner doesn't light Oven runs erratically or won't maintain temperature Igniter visibly cracked, broken, or with a damaged element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas oven igniter directly replaces the following OEM and cross-reference part numbers: 316489403, 5304508786, 7316489403, Model 501RB, AH2364063, EA2364063, EAP2364063, AFR16172, AP4433236, PD00000756, PS2364063. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: on some models this is the broil (upper) igniter, and the bake (lower) igniter is a different part — see the FAQ below on bake vs broil igniters. Compatibility This gas oven igniter is compatible with select gas ranges, ovens, and stoves from the following brands: Frigidaire gas ranges and ovens — including many Frigidaire Gallery models (LGGF, FGGF, FFGF series and related) Electrolux gas ranges and ovens (select models) Crosley gas ranges and ovens (select models) Gibson gas ranges and ovens (select models) Kelvinator gas ranges and ovens (select models) Tappan gas ranges and ovens (select models) White-Westinghouse gas ranges and ovens (select models) Ikea gas ranges and ovens (select Frigidaire-built models) Kenmore / Sears gas ranges and ovens (select Frigidaire-built models, including 790-series) Note: This igniter fits specific models — always verify against your appliance's model number before ordering. On ranges with two igniters (a bake igniter and a broil igniter), confirm which one you need (see the bake-vs-broil FAQ below). Contact our support team with your model number if you're unsure. Key Features Gas oven igniter — heats up to ignite the burner and draws current to open the gas safety valve Flat-style, open-cage design Resolves "won't light," "slow to heat," "uneven heating," "glows but won't ignite," and "gas smell" symptoms caused by a weak or failed igniter Electrical rating: 3.2–3.6 amps, 120V AC Silicon carbide and ceramic construction — high heat resistance and long service life Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; lead and plug approximately 16" long Includes the flat-style igniter assembly with bracket and leads/plug (some kits include ceramic wire nuts) Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 316489403 Part Type Gas Oven Igniter (Flat Style, Open Cage) Condition Aftermarket Replacement Application Gas Ranges, Ovens, and Stoves (Frigidaire platform) Amperage 3.2–3.6 Amps Voltage 120V AC Igniter Style Flat, open cage Overall Dimensions 3-1/2"L x 1-3/4"W x 13/16"H Ceramic Block 1.5" L Lead Length Approximately 16" Material Silicon carbide / ceramic / metal Color Almond / White / Gray Includes Igniter assembly with bracket and leads/plug Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Shut off the gas supply to the range at the shutoff valve and disconnect electrical power at the breaker before beginning any repair. After installation, if you smell gas at any point, leave the area immediately and contact your gas utility provider. If you're not comfortable working around gas components, have this repair done by a qualified appliance technician. Improper gas appliance repairs can cause fire, explosion, or carbon monoxide hazards. ⚠️ Handle the Igniter by the Bracket Only — The Element Is Fragile Disconnect power at the breaker and shut off the gas supply before beginning. Wear work gloves and safety glasses. The silicon carbide igniter element is extremely fragile and cracks easily — handle the new igniter only by its metal bracket, never by touching the element itself. Skin oils and any impact can shorten its life or break it. Locate the igniter: the bake igniter is beneath the oven floor panel (remove the oven racks, then the floor panel, and on some models the bottom drawer for access), while the broil igniter is mounted near the top of the oven cavity. Photograph the wiring connection before disconnecting. Disconnect the old igniter's wire leads at the connector (they're often joined with ceramic wire nuts). Remove the screws securing the old igniter bracket and lift it out. Install the new 316489403 by securing its bracket in the same position and orientation, then connect the wire leads (use the included or existing ceramic wire nuts — regular wire nuts can't handle the heat). Route the leads away from the burner flame. Restore gas and power. Test by setting the oven to bake (or broil, if that's the igniter you replaced) — the igniter should glow bright orange within a minute or so, and the burner should light within about 60–90 seconds. Tools needed: Nut driver, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions My igniter glows but the oven won't light — do I still need to replace it? Yes — this is actually the most common way an oven igniter fails, and it's counterintuitive. The igniter has two jobs: to get hot enough to ignite the gas, AND to draw enough electrical current to open the gas safety valve. As an igniter ages, it can still glow (so it looks like it's working) but weaken to the point where it no longer pulls enough current to open the safety valve — so no gas is released and the burner never lights. If your igniter glows orange but the burner doesn't light within about 90 seconds, the igniter is weak and needs replacement. A good rule of thumb: if it takes more than 90 seconds from glow to flame, the igniter is on its way out. Is the 316489403 the bake igniter or the broil igniter? This is an important distinction, and there's genuine confusion in the industry about it. On many Frigidaire gas ranges, the 316489403 is used as the broil (upper) igniter with an approximately 14–16" lead, while the bake (lower) igniter is a different part — 5304506545 (which superseded 316489404) — often with a shorter lead. However, some sources and parts diagrams list them differently or even reversed, and on some models the 316489403 serves the bake position. The safest approach: look up YOUR specific model number to confirm which igniter you need, and compare your old igniter's lead length to the replacement. If your old igniter's leads reach a connector far from the igniter (14–16"), the 316489403 with its 16" lead is likely correct. Contact our support team with your model number and we'll confirm. Why do I smell gas when I try to use the broiler? If you smell gas when the broiler's safety valve opens but the burner doesn't light, it usually means the igniter isn't getting hot enough (or drawing enough current) to ignite the gas that's being released — so raw gas escapes before shutting off. This points to a weak igniter. To confirm which part is at fault: with the gas off, do a voltage test at the oven safety valve on the broil side — you should read between 3.0 and 3.3 VAC. If the voltage is correct but the burner won't light, the igniter is the problem. If there's no proper voltage, or the burner tube has spider webs or debris blocking it, address those first. Also inspect the gas supply tube from the safety valve to the burner for damage or loose connections. Why do I need to handle the igniter so carefully? The igniter's heating element is made of silicon carbide, a material that's excellent at withstanding heat but is brittle and cracks easily from impact or flexing. Even touching the element with bare fingers can leave oils that create hot spots and shorten its life, and a small bump can crack it invisibly, causing premature failure. Always handle the new igniter by its metal bracket, never by the element or the ceramic block. When installing, be careful not to bump the element against the oven walls or burner. This care is the single biggest factor in whether your new igniter lasts years or fails early. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from silicon carbide and ceramic to match the electrical specifications (3.2–3.6A, 120V AC), flat open-cage style, dimensions (3-1/2"L x 1-3/4"W x 13/16"H, 16" lead), and ignition function of the original 316489403 gas oven igniter used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10918546CM Gas Oven Igniter Replaces Part Numbers: W10918546, W10140611, 98005652, W10918546VP, WPW10140611, AP6037202, PS11770066. 3.4 - 3.6 Amp, 1.5" block, 3.75" cage, 10" leads w/male pins. Bake igniter for specific single burner Whirlpool range models. Description: This Oven Igniter is a replacement part for select Maytag, Kenmore, Whirlpool gas oven models, responsible for igniting the gas burner that heats the oven. It works by drawing electrical current through the igniter filament, heating it to a high temperature until it glows and ignites the gas to start the cooking process. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 5304509706 Gas Oven Igniter Product Overview The XPARTCO 5304509706 Gas Oven Igniter is designed to ignite the gas burner and ensure consistent oven heating performance. This Oven Igniter is a replacement part for select Frigidaire, Kenmore, GE gas oven models, designed to ignite the gas in the oven burner to start the heating process. This part is responsible for creating the spark that ignites the gas, providing the heat needed to cook and bake food. Over time, the oven igniter can wear out or become damaged, which can prevent the oven from heating. Quick Answer If your gas oven is not heating, takes too long to preheat, or the burner does not ignite, the 5304509706 igniter may be weak or faulty. Replacing this igniter restores proper ignition and consistent oven performance. Replaces Part Numbers Replaces OEM part number: 5304509706, 316489402, 316489408, 316119301, 4545981, 012505482182, EAP12071409, AFR18015, PD00035904, AP6230715, PS12071409, WB2X10016, WB02X10016, 1704, EAP241804, AGE826644, PD00042950, AH241804, EA241804, AP2009619, PS241804. Compatibility This gas oven igniter is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible gas ranges and ovens. Frigidaire Gas Ranges Electrolux Ovens GE Gas Ranges Kenmore Gas Ovens Always verify your appliance model number before ordering. Common Problems This Part Fixes Oven not heating Slow or delayed ignition Burner not lighting Gas smell due to ignition failure Key Features Designed for gas oven ignition Provides fast and reliable burner ignition High-quality aftermarket replacement Durable construction for long-lasting performance Product Specifications Part Number: XP5304509706 Part Type: Gas Oven Igniter Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Gas Ovens & Ranges Troubleshooting Guide Oven not igniting → Faulty igniter Long preheat time → Weak igniter No flame despite gas flow → Igniter failure When Should You Replace This Igniter? Replace this igniter if your oven fails to heat, takes too long to preheat, or does not ignite the gas burner properly. Installation Notes ⚠️ Disconnect power and shut off gas before installation. Remove mounting screws, disconnect wiring, and install the new igniter carefully. Avoid touching the igniter surface with bare hands. Related Parts Gas Oven Safety Valve Oven Temperature Sensor Control Board Frequently Asked Questions Will this igniter fit my oven?This igniter fits many Frigidaire and compatible gas ovens. Always verify your model number. What does an oven igniter do?It ignites the gas burner and allows the oven to heat properly. What are signs of a bad igniter?Oven not heating, delayed ignition, or no flame during operation. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

1408 Gas Furnace Hot Surface Igniter The 1408 is a replacement 120V silicon carbide hot surface igniter for gas furnaces. When the furnace calls for heat, the igniter glows white hot and lights the gas burners. Over time the element can crack or wear out, and a failed igniter is a common reason a gas furnace tries to start but never lights or never heats. This igniter replaces the Robertshaw 41-408 and the Rheem 62-22868-93. It is a furnace igniter, not an oven igniter, so check the part number and the look of your old igniter before ordering. Quick Answer The 1408 Gas Furnace Igniter replaces a cracked, burned-out, or failed hot surface igniter on a gas furnace that tries to start but won't light. Replaces 41-408 and 62-22868-93. Classic symptom: the inducer runs, but the igniter never glows and the burners never light. Common Problems This Part Fixes Furnace won't light, with no heat Igniter does not glow when the furnace calls for heat Cracked, broken, or visibly damaged igniter element Furnace cycles through ignition attempts and then locks out Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This igniter directly replaces the following part numbers: 1408, 41-408, 62-22868-93, 62-22868-02, 62-22868-82, 62-22441-01, 62-22868-92, B340039P01, 767A-372, 271N, IG408, 41-408, 67900, IG1408 The first three numbers are the main references for this igniter. The others appear on retailer cross-reference lists. Confirm against your furnace's parts list, or contact our support team, if your furnace calls out a different number. Compatibility This igniter is a replacement for the Robertshaw 41-408 and the Rheem 62-22868-93, and it is used on gas furnaces that call for either one. The Rheem number is used on Rheem, Ruud, WeatherKing, and Protech furnaces, including these series examples: Rheem/Ruud UGDG, UGLG, UGLH, UGPH, UGTA, UGVG Rheem/Ruud 80LJ, 80PJ, 90RJ, 90TJ Note: The series above are a sample, not a full list. Retailers do not list the lead length or connector style for this igniter, so compare your old igniter's shape, lead, and connector to the new one, and contact our support team with your furnace model number to verify fit before ordering. Key Features 120V silicon carbide hot surface igniter for gas furnaces Replaces Robertshaw 41-408 and Rheem 62-22868-93 Resolves no-light and no-heat problems caused by a failed igniter Furnace igniter, not for gas ovens Product Specifications Part Number 1408 OEM Part Number 62-22868-93, 41-408 Part Type Gas Furnace Hot Surface Igniter Condition Aftermarket Replacement Element Material Silicon Carbide Voltage 120V Application Gas Furnaces Installation Notes ⚠️ Turn Off Power and Gas Before Installing Switch off power to the furnace at the breaker and the furnace switch, and shut off the gas supply, before beginning. Wear work gloves. Let the old igniter cool, disconnect its lead, remove it, and fit the new igniter in the same position. Handle the new igniter only by its ceramic base, and avoid touching the silicon element, since skin oils can cause early failure. If the furnace still does not light, check the control board and the gas valve. Frequently Asked Questions My furnace won't light. Is this the part I need? A cracked or burned-out igniter is a common cause. If the igniter doesn't glow when the furnace calls for heat, or the element is visibly cracked, it is likely the problem. If the igniter glows but the burners don't light, check the gas valve and control. Does this replace the Robertshaw 41-408 and the Rheem 62-22868-93? Yes, it is listed as a replacement for both. Because retailers do not list lead length or connector style, compare your old igniter to this one, or contact our support team, before ordering. Why shouldn't I touch the igniter element? Skin oils on the silicon element can cause the igniter to fail early. Handle it by the ceramic base only. Will this fit my furnace? It is used on gas furnaces that call for a 41-408 or 62-22868-93 igniter, but the series list above is only a sample. Check your furnace's parts list, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less