Search results for "stacking kit"

WH13X10029 Genuine OEM GE Washer Water Valve The WH13X10029 is a genuine GE OEM water inlet valve for GE, Hotpoint, Haier, Monogram, and Café front-load washers. This is a 2-inlet, 3-outlet valve assembly built around three internal solenoids: two work together during the wash portion of the cycle, opening in different combinations depending on the wash temperature you select, while the third solenoid handles the dedicated cold-only rinse. Because three separate solenoids share one valve body, a failure in any single one of them can affect only part of your washer's fill behavior while the rest continues working normally. Rated 120V, 60Hz, and measuring approximately 5-3/8"L x 3-1/8"W x 2-1/2"H, this valve ships as a complete 3-solenoid assembly with its mounting bracket included. Common failure symptoms include the washer continuing to fill after it should have stopped, slow filling, or a complete failure to fill on one specific water temperature setting while others work fine. It directly replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392. As a genuine OEM part, the WH13X10029 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X10029 Genuine OEM GE Washer Water Valve fixes GE, Hotpoint, Haier, Monogram, and Café front-load washers that won't shut off after filling, fill slowly, or won't fill on a specific temperature setting (such as cold-only rinse) while other settings work fine. 2-inlet, 3-outlet, 3-solenoid valve assembly with mounting bracket, 120V, 60Hz, 5-3/8"L x 3-1/8"W x 2-1/2"H. Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, PS1482392. Genuine OEM — manufactured by GE to factory specifications for guaranteed fit, materials, and performance. Common Problems This Part Fixes Washer keeps filling and won't shut off, even after reaching the correct level Washer fills much more slowly than it used to Washer won't fill at all on one specific temperature setting while other settings work normally Cold-only rinse cycle failing to fill while wash-cycle fills work fine (or vice versa) Cycle stalling at the fill step and never advancing to wash Water leaking or dripping near the valve connections Washer stopping mid-cycle due to a fill-related fault Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water valve directly replaces the following OEM and cross-reference part numbers: WH13X10029, 33090039, PD00001515, EAP1482392, AGE26067, AH1482392, EA1482392, AP4303282, PS1482392. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE, Hotpoint, Haier, Monogram, and Café front-load washers, including model families such as GFA, GFW, GMA, and WBV, and specific models such as GFWS1600H, GFWS1605H, GFWS1700H, and GFWS1705H. Note: This valve is specific to GE's front-load washer platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and flow-rate calibration Complete 3-solenoid water valve assembly — 2 inlets (hot and cold), 3 outlets Two solenoids manage the wash-cycle fill combinations by temperature selection; a third handles cold-only rinse Resolves "won't shut off," "fills slowly," and "won't fill on a specific temperature setting" symptoms caused by valve failure Includes the mounting bracket — no need to transfer hardware from the old valve Rated 120V, 60Hz Approximately 5-3/8"L x 3-1/8"W x 2-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392 Compatible with GE, Hotpoint, Haier, Monogram, and Café front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH13X10029 Condition Genuine OEM Part Type Washer Water Inlet Valve (2-In / 3-Out, 3-Solenoid) Brand GE Application Front-Load Washers Voltage 120V Frequency 60 Hz Inlets 2 (hot and cold) Outlets 3 Solenoids 3 (one double, one single, one dedicated cold-rinse) Dimensions 5-3/8"L x 3-1/8"W x 2-1/2"H Kit Contents Valve assembly + mounting bracket Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Stackable Units May Need A Second Person Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. If your washer is part of a stacked laundry center, the dryer sitting on top will need to be removed first to access the top of the washer — this is much easier with a second person helping to lift and support the dryer safely. Remove the screws securing the top panel of the washer, then slide the panel back and lift it off to access the valve assembly. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything, since this valve has multiple solenoids and outlet hoses that must be reconnected in the correct positions. Disconnect the electrical connectors and the three outlet hoses from the old valve, then remove its mounting screws and pull it free along with its bracket. Install the new WH13X10029 assembly in the same position, reconnect all three outlet hoses to their original positions, reconnect the electrical connectors, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the top panel, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings, including a cold-only rinse if your washer has one, to confirm each solenoid is filling and shutting off correctly. If this is a stackable unit, carefully reposition the dryer back on top once testing is complete. Tools needed: Phillips screwdriver, pliers, towel, work gloves, and a helper for stackable units. Frequently Asked Questions My washer won't shut off and keeps filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve on this platform. A worn internal seal on one of the three solenoids can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only my cold-only rinse doesn't fill, but regular wash cycles work fine. Do I need the whole valve? Yes. This valve houses three separate solenoids in one assembly — two that combine for wash-cycle fills at different temperatures, and one dedicated specifically to the cold-only rinse. If just one of those three has failed, the others can continue working normally, which is exactly why a single-cycle fill problem can appear alongside otherwise normal operation. The three solenoids aren't sold or serviced individually, so replacing the complete assembly is the correct repair even if only one function is affected. Do I really need to remove the dryer if this is a stacked unit? On most stacked laundry centers, yes — the top panel of the washer sits underneath the dryer, so the dryer needs to come off first to get access. This is a heavier, more awkward step than the rest of the repair, so it's worth having a second person help lift and support the dryer safely rather than attempting it alone. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-solenoid design, flow rate, and mounting configuration as the water valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

MWCDF-095-2Kit Microwave Capacitor, Diode & Fuse Kit – Universal High-Voltage Repair Kit Product Description Restore proper microwave heating and electrical safety with the MWCDF-095-Kit Microwave Capacitor, Diode & Fuse Kit. This high-quality aftermarket repair kit includes the three most common high-voltage components required to fix no-heat and power-related microwave issues: a high-voltage capacitor, high-voltage diode, and high-voltage fuse. Failed components in the HV circuit can cause the microwave to run without heating, blow fuses, or shut down completely. Replacing the full kit helps ensure reliable heating and safe operation. This Kit Includes Following Parts: 1 Capacitor 2 universal Diode (EXPHV10)  2 Ceramic Fuse (20 amp) 6.35 x 32 mm 2 5Kv Fuse (0.9A) 6x40mm Replaces Part Numbers Capacitor Replaces Part Numbers: TJ13QBP21095, 13QBP0300, 13QBP21095, AP5633423, RC-QZA234WRE0, RC-QZB011MRE0, RCQZA331WRZZ, 5304513458, PD00065299, EAP12365444, 4584979, AP6301645, PS12365444, 00631397, 631397, PD00044249, EAP10057840, 4161979, AP5950362, PS10057840, WB27X11031, PD00040188, EAP2339855, 1474116, AP4362390, PS2339855, WB27X10073, PD00045875, EAP239187, 769853, AP2025984, PS239187, WB27X11011, PD00087136, EAP2345628, 1474103, AP4368101, PS2345628, 2501-001016, 2028385, AP4033712, PS4130923, 8206562, PD00074258, EAP1486840, 1200936, AP3890709, PS1486840, 5304528930, 5304464253, AP7017693, PS2203382, WB27X10009, 254534, AH239117, EA239117, AP2025928, PS239117, WP815073, AP6011690, PS11744888, 2501-000260, AP4033659, PS4130923 and more Compatibility This universal microwave high-voltage repair kit is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that use a 0.95 µF high-voltage capacitor, standard microwave HV diode, and HV fuse. Commonly used in countertop, over-the-range, and built-in microwave models. Always verify capacitor rating and fuse specifications before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Built to OEM-equivalent electrical specifications ⚡ Complete HV Circuit Repair – Includes capacitor, diode, and fuse 🔥 Fixes No-Heat Issues – Restores proper magnetron power delivery 🛡️ Improves Electrical Safety – Protects microwave from overload and failure 💰 Cost-Effective Solution – Avoids expensive magnetron replacement 📐 Product Specification Kit Name: MWC-095-Kit Component Type: Microwave High-Voltage Repair Kit Capacitor Rating: 2100 VAC, 0.95 µF Diode Type: Microwave high-voltage diode Fuse Type: Microwave high-voltage fuse Application: Magnetron high-voltage power circuit Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:Microwaves contain EXTREMELY HIGH VOLTAGE, even when unplugged. Always discharge the high-voltage capacitor before servicing. Professional installation is strongly recommended. Basic Steps: Unplug the microwave and remove the outer cabinet. Safely discharge the existing high-voltage capacitor. Remove the old capacitor, diode, and fuse. Install the new components from the MWCDF-095-Kit. Reassemble the cabinet and restore power. Test microwave heating operation. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave heating safely and efficiently — Add to Cart Now for a complete, budget-friendly repair solution!

Read more less

EXP694 Dryer Repair Kit Replaces DC97-16782A, 6602-001655, DC93-00634A The EXP694 Dryer Repair Kit is a complete drum system rebuild solution designed to restore smooth, quiet, and efficient dryer operation. This kit includes the most common wear components found inside your dryer: drum belt, idler pulley, and drum support rollers. Over time, these parts wear down together, causing squeaking, grinding, drum slippage, or complete failure to spin. Replacing all components at once ensures proper alignment, eliminates noise, and prevents repeat breakdowns — making this the most effective long-term repair solution. Quick Answer The EXP694 Dryer Repair Kit fixes dryers that won’t spin, make loud squeaking or grinding noises, or stop tumbling. It replaces the belt, rollers, and idler pulley to restore smooth and quiet drum operation. Note: Includes four rollers (each with shaft and two tri-rings), one idler pulley, and one belt. Replace all four rollers for even wear. Inspect the drum and felt seal (e.g., DC97-07618A) for wear. Clean lint from the drum and cabinet to prevent overheating. Common Problems This Part Fixes Dryer drum not spinning or slipping Loud squeaking, grinding, or thumping noises Uneven or slow drum rotation Dryer stopping mid-cycle Excessive vibration or instability Worn belt, rollers, or idler pulley components Replaces Part Numbers This repair kit replaces the following common drum system components: Drum Roller: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648 Idler Pulley: DC93-00634A, AP6038887, DC96-00882C, DC61-01230B, DC96-00882B, PS11771601, 12002777, AP4010261, 1401171, 35001083, 35001098, 35001276, AH2004052, DC61-01215A, DC96-00882B, EA2004052, PS2004052 Drum Belt: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This repair kit is compatible with select dryers from the following brands: Samsung dryers (gas and electric models) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drum repair kit including belt, rollers, and idler pulley OEM-equivalent fit, performance, and durability Eliminates noise and restores smooth drum rotation Prevents repeat repairs by replacing all wear components together Cost-effective all-in-one repair solution DIY-friendly installation with basic tools Product Specifications Includes 4 drum rollers (DC97-16782A, ~3-1/4" diameter x 1-1/8" width, blue/black plastic/rubber, metal shaft, self-lubricating bushing with ball bearing, each with shaft and two tri-rings), 1 idler pulley (DC93-00634A, metal/plastic), 1 drum belt (6602-001655, 92" long, 5 ribs, neoprene), kit dimensions ~10"L x 6"W x 4"H. Part Type Dryer Repair Kit Includes Belt, Rollers, Idler Pulley Application Dryer Drum System Condition Aftermarket Replacement Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Disconnect power before servicing. Remove dryer panels, release belt tension, and replace worn components. Ensure proper alignment of the belt and rollers before reassembly. For best results, replace all components included in this kit at the same time. Frequently Asked Questions Should I replace all parts at once? Yes. The belt, rollers, and pulley wear together. Replacing all components ensures smooth operation and prevents future breakdowns. Will this fix dryer noise? Yes. This kit resolves most squeaking, grinding, and thumping noises caused by worn drum components. Is this an OEM part? This is a high-quality aftermarket repair kit built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP653 Dryer Idler Pulley and Belt Set – Replaces 6602-001655, DC93-00634A – Compatible with Samsung & Kenmore Dryers Product Description Restore smooth drum rotation and proper belt tension with the EXP653 Dryer Idler Pulley and Belt Set. This high-quality aftermarket repair kit includes a dryer drum belt and idler pulley, designed to work together to keep the drum turning quietly and efficiently. Worn belts or failing idler pulleys can cause squealing noises, belt slippage, or a drum that won’t rotate. Replacing both components at the same time helps ensure long-lasting performance and prevents repeat breakdowns. EXP653 is an aftermarket solution built to OEM-equivalent specifications, offering reliable performance at a cost-effective price. Replaces Part Numbers Drum Belt Replaces: 6602-001655, 6602-001314, 5PH2337, PD00002012, EXP645, EAP2407938, AP4373659, PS4133825.  Idler Pulley Replaces:  DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, EXP645, 4455850, PD00032419, EAP11771601, AP6038887, PS11771601. Compatibility This replacement dryer belt and idler pulley set fits select Samsung and Kenmore (Samsung-manufactured) electric dryers. Example compatible models include (but are not limited to): Samsung DV42H5000EW, DV45H7000EW Kenmore 592.89003, 592.89004 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Designed to match OEM fit and performance 🌀 Restores Smooth Drum Rotation – Ensures proper belt tracking and tension 🔇 Reduces Noise & Vibration – Helps eliminate squealing or grinding sounds 💪 Durable Construction – Reinforced belt and heavy-duty pulley bearing 💰 Cost-Effective Repair – Replaces multiple wear parts in one kit 📐 Product Specification Kit Name: EXP653 Component Type: Dryer Belt & Idler Pulley Set Includes: Dryer drum belt and idler pulley Belt Style: Ribbed, OEM-equivalent length Pulley Type: Bearing-style idler pulley Application: Drum drive and belt tension system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Basic Steps: Disconnect dryer power. Open the cabinet and remove the drum. Remove the worn belt and idler pulley. Install the new EXP653 idler pulley. Route and install the new drum belt correctly. Reinstall the drum, reassemble the dryer, and restore power. Run a test cycle to confirm quiet, smooth operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Fix belt noise and restore smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 4392065 Dryer Maintenance Kit Replaces 349241T, 341241, WP691366 The XPARTCO 4392065 is an aftermarket dryer maintenance and repair kit containing the three most commonly replaced drum drive components for Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the drum belt (341241), idler pulley (691366), and rear drum support roller kit (349241T) — the three parts that work together to drive and support the dryer drum, and that most frequently cause squealing, thumping, no heat, and drum-not-spinning issues when worn. Replacing all three parts together in a single repair is the recommended approach — since these components wear at similar rates and the dryer must be fully disassembled to access any one of them, doing all three at once saves significant time and cost compared to replacing them individually. The kit contains everything needed: 1 drum belt, 1 idler pulley, 2 drum support rollers, 4 tri-rings, and 2 retaining washers. Installs in 45–60 minutes with basic hand tools. Quick Answer The XPARTCO 4392065 Dryer Maintenance Kit fixes squealing, thumping, no heat, and drum-not-spinning issues in Whirlpool-family 29" dryers in a single repair. Includes 1x 341241 drum belt (92-1/4" x 1/4", 4 ribs), 1x 691366 idler pulley, 2x 349241T drum rollers, 4x tri-rings, and 2x retaining washers. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef dryers. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Dryer drum not spinning — motor runs but belt has broken Clothes not tumbling or drying properly Grinding or rumbling noise from the drum area Dryer drum spinning unevenly or stopping intermittently Belt repeatedly slipping or breaking due to worn idler pulley Drum vibrating excessively due to worn roller bearings What's in the Kit Part 1 of 3 — 1 included 341241 Dryer Drum Belt 92-1/4" L x 1/4" W · 4 ribs, 3 grooves · Neoprene rubber · Wraps around the drum and connects to the idler pulley and motor pulley to drive drum rotation Part 2 of 3 — 1 included 691366 Idler Pulley Sturdy plastic with metal shaft and idler arm · Maintains correct tension on the drum belt between the motor and drum · Self-lubricating bearing Part 3 of 3 — 2 included 349241T Rear Drum Support Roller Kit 2 drum rollers · Reinforced self-lubricating metal bearings, thickened rubber wheel · Supports the rear of the drum as it rotates · Includes 4 tri-rings and 2 retaining washers Replaces Part Numbers Kit (4392065) cross-references: 4392065, 2014, 26000279435, 26000279436, 279435, 279436, 279708, 279708MS, 279709, 279709MS, 279860, 279948, 4392065VP, 587636, 80046, 8106, 8237, 8238, AWP39348, PD00002464, AH373087, EA373087, AP3131942, PS373087. 341241 Belt cross-references: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AP2946843, PS346995, TJ341241. 691366 Idler Pulley cross-references: WP691366, 691366, 239477, 26000691366, 3346, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, AP6010582, PS11743765. 349241T Drum Roller cross-references: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AP3098345, PS347627. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select 29-inch large-capacity gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Note: This kit is designed for 29-inch large-capacity Whirlpool-family dryers. If your dryer is a compact or stackable model, verify compatibility with our support team before ordering. Key Features Three-part kit addresses the most common drum drive failures in a single repair — saves time and cost vs. replacing parts individually Belt: 92-1/4" x 1/4", 4 ribs, 3 grooves — premium neoprene rubber resists cracking, heat, and stretching Idler pulley: sturdy plastic with metal shaft and self-lubricating bearing — maintains correct belt tension Drum rollers: 2 included — reinforced self-lubricating metal bearings and thickened rubber wheels for quiet, stable drum support All hardware included: 4 tri-rings and 2 retaining washers — everything needed for complete installation Since the dryer must be disassembled to access any one of these parts, replacing all three at once eliminates repeated teardowns Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392065 Condition Aftermarket Replacement Application 29-inch Gas and Electric Dryers Kit Includes 1x 341241 Drum Belt, 1x 691366 Idler Pulley, 2x 349241T Drum Rollers, 4x Tri-rings, 2x Retaining Washers Belt Length 92-1/4 inches Belt Width 1/4 inch Belt Ribs 4 ribs, 3 grooves Belt Material Neoprene rubber Idler Pulley Material Plastic / Metal Drum Roller Quantity 2 rollers (replace both at same time) Roller Lubrication Self-lubricating bearings — no grease needed Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, then lift the drum out. Remove the old belt, idler pulley, and drum rollers. Install the 2 new 349241T rollers onto the rear bulkhead shafts, pressing the new tri-rings and washers into place. Install the new 691366 idler pulley onto the idler arm. Loop the new 341241 belt around the drum with the ribbed side facing inward, then route it around the idler pulley and motor pulley. Reinstall the drum, reassemble the front and top panels, and restore power. Run a test cycle to confirm quiet operation. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, needle-nose pliers, flat pry tool. Frequently Asked Questions Why should I replace all three parts at the same time? The drum belt, idler pulley, and drum support rollers all work together as a system and wear at similar rates under the same conditions. Since the dryer must be fully disassembled to access any one of these parts, replacing all three in a single repair is far more cost-effective than replacing them one at a time — which would require three separate teardowns. This is the same reason the 4392065 maintenance kit was designed: one repair, all three parts, done. What does each part in this kit do? The 341241 drum belt wraps around the outside of the drum and connects to the idler pulley and motor pulley — the motor drives the belt, which spins the drum. The 691366 idler pulley maintains tension on the belt so it grips the drum and motor pulley properly. The 349241T drum rollers are support wheels mounted on the rear of the dryer that cradle and support the back edge of the drum as it rotates. All three are essential to smooth, quiet drum operation. How is this kit different from the 4392067 repair kit? The 4392065 and 4392067 kits are designed for different Whirlpool-family dryer generations. The 4392065 uses the 341241 belt (92-1/4" x 1/4", 4 ribs) and the 691366 idler pulley, and is for older 29-inch Whirlpool-family dryers. The 4392067 uses the 661570V belt (93-1/2" x 1/4", 4 ribs) and the W10837240 idler arm assembly, and is for newer Whirlpool-family dryers (those with the lint screen inside the door). Use your model number to confirm which kit fits your specific dryer before ordering. Do I need to lubricate the drum rollers after installing? No — the 349241T drum rollers include self-lubricating bearings and do not require any additional grease or oil after installation. Applying grease to self-lubricating rollers is not recommended and can actually attract lint and debris, causing the rollers to wear faster. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM kit, but all three included components are manufactured from premium neoprene rubber, durable plastic, and metal to match the dimensions and performance of the original 4392065 kit parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet. This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours. Quick Answer The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258. Common Problems This Part Fixes Dishes not getting clean — food soil, grit, or film left behind after a full cycle Top rack not getting wet or not getting cleaned while the bottom rack washes normally Spray arms turning slowly or not turning at all — insufficient water pressure Loud humming, whining, or grinding noise during the wash portion of the cycle Dishwasher runs a full cycle quietly with no audible water circulation Water pooling in the base pan under the dishwasher from a leaking pump shaft seal Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle Cleaning performance that has gradually declined over months as bearings wear Pump motor humming but the impeller not turning — seized shaft or jammed impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers: WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands: GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series) Café dishwashers (CDT865 and CDT866 series) Monogram dishwashers (ZDT915 and ZDT975 series) Hotpoint dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS. Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump Drives water through the lower spray arm, middle spray arm, and upper wash manifold Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure Sealed shaft design protects the motor from sump water intrusion Direct drop-in replacement for the superseded WD26X22789 — no modifications required Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD26X25103 Part Type Dishwasher Variable Wash Pump Kit (Circulation Pump) Condition Genuine OEM Brand GE Appliances Motor Type Variable speed Voltage 120V / 60 Hz Function Circulates water under pressure to the spray arms and upper wash manifold Kit Contents Wash pump assembly + integrated wiring harness Location Underneath the tub, mounted to the sump housing Connections 2 hose clamps + 2 electrical connections Supersedes WD26X22789 Repair Difficulty Moderate — 1 to 2 hours Quantity 1 pump kit Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, Haier Installation Notes ⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves. Frequently Asked Questions My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump? It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced. What does "variable" mean on this pump, and does it matter? It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly. The dishwasher is making a loud grinding noise. Do I need the whole pump? Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak. I found water in the pan underneath the dishwasher. Could the pump cause that? Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear. Does this kit include everything, or do I need to reuse parts from the old pump? The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks." What's the difference between WD26X25103 and WD26X22789? They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE49X20697 Dryer Genuine OEM Front Bearing Repair Kit This Kit Includes Following Parts WE3M26 top front bearing WE09X27634 front drum felt WE03X29897 drive belt 2 x WE03X37317 bearing slides, 2 x WE03X37318 glide slides Replaces Part Numbers:WE49X20697, AP5806906, PS9493092, WE03X37318, WE1M504, WE01M0333, WE1M333, AP7217724, WE03X37317, WE1M1067, WE01M0316, WE1M316, WE1M481, WE1M507, AP7217723, WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, WE3M26,  1089201, AH960316, EA960316, PS960316, WE03M0020, WE3M20, AP3790641, WE09X27634, WE09X20441, WE9M30, WE09M0015, WE9M15, AP6889049.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WE49X21874 Dryer Front Bearing Repair Kit Replaces Part Numbers: WE49X21874, AP5970729, 4379300, PS11700897, WE14M124,  1257069, AH1766010, EA1766010, WE14M106, WE14M120, WG04L00523, AP4297334, PS1766010, WE09X27634, WE09X20441, WE9M30, WE09M0015, WE9M15, AP6889049, PS12722961, WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, PS16542496, WE03X37318, WE1M504, WE01M0333, WE03X37318-50PK, WE1M333, AP7217724, PS17137205, WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AP7217723, PS17137203. This Kit Includes Following Parts WE14M124 top front bearing WE09X27634 front drum felt WE03X29897 drive belt 2 x WE1M504 bearing slides, 2 x WE1M1067 glide slides Description: The WE49X21874 Dryer Bearing Kit is designed for front-load dryers and makes servicing the dryer easy, affordable, and convenient. This kit works for select GE front-load dryer models. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

EXP696 Dryer Drum Roller & Belt for Samsung Replaces DC97-16782A, 6602-001655 This Kit Included Following Parts:4 X Drum Rollers DC97-16782A 1 X Drum Belt  6602-001655    Drum Roller Replaces Part Numbers: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648  Drum Belt Replaces: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240 The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy. Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system. Quick Answer The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. What's in the Kit Part 1 of 2 Dryer Drum Belt — Replaces WPW10112954 93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation Part 2 of 2 Idler Pulley Assembly with Bracket — Replaces W10837240 2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door Common Problems This Kit Fixes Dryer drum not spinning — motor runs but drum stays still Loud squeaking, squealing, or grinding noise during operation Clothes not tumbling during the drying cycle Thumping or slapping noise when dryer is running Belt slipping off or repeatedly breaking Burning rubber smell coming from the dryer Dryer drum turning erratically or stopping while motor continues to run Replaces Part Numbers Drum Belt (WPW10112954) cross-references: WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388. Idler Pulley Assembly (W10837240) cross-references: W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244. If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric — fits models with lint screen inside door) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Crosley dryers Admiral dryers Inglis dryers Roper dryers Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering. Key Features Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation Replacing both parts together saves a second disassembly if the other part fails soon after Aftermarket replacement built to OEM-equivalent quality standards Belt directly replaces WPW10112954 / W10112954 — no modification required Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required DIY-friendly repair — installs in 30–60 minutes with basic hand tools Product Specifications Kit Part Number EXP651 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240) Belt Length 93-1/4 inches Belt Width 5/16 inch Belt Height 1/8 inch Belt Ribs 5 ribs, 4 grooves (Multi-V) Belt Material Rubber Pulley Diameter 2-1/8 inches Pulley Overall Dimensions 6-1/4" L x 1-1/4" W x 3-7/16" H Pulley Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Why should I replace the belt and idler pulley at the same time? The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa. How does the W10837240 differ from other Whirlpool idler pulleys? The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering. What is the difference between WPW10112954 and W10112954? These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit. Should I also replace the drum rollers at the same time? It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering. Are these OEM or aftermarket parts? Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less