Search results for "washer belt, motor"

XPARTCO 22003483 Washer Drive Belt The XPARTCO 22003483 is an aftermarket replacement drive belt for Whirlpool-built Maytag Atlantis top-load washers. This belt is the mechanical link between the drive motor and the washer's drive system — it's what actually transmits the motor's rotation to spin the drum, so both agitation and spin depend entirely on this belt gripping its pulleys correctly and staying properly tensioned. Made of black rubber, this belt measures 52 inches long. Over years of use, the belt material gradually hardens and glazes over, becoming smooth and "slick" rather than gripping the pulleys firmly — this degradation can cause the belt to slip under load even before it shows any visible cracking or damage. A worn belt produces a range of symptoms depending on how far the wear has progressed: the washer may pump water but fail to spin, fail to agitate at all, spin noticeably slower than normal, or produce a chirping or slipping noise, especially as the motor shifts between wash and spin modes. It directly replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667. Quick Answer The XPARTCO 22003483 Washer Drive Belt fixes Maytag (Whirlpool-built) top-load washers that pump but won't spin, won't agitate, spin slowly, or make a chirping/slipping noise as the motor shifts modes. 52 inches long, black rubber. Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, 824667. A belt can slip and cause symptoms well before it looks visibly worn — years of use leave the rubber "slick" and unable to grip the pulleys properly, even without visible cracking. Common Problems This Part Fixes Washer pumps water but won't spin Washer won't agitate Washer spins noticeably slower than it used to Chirping or slipping noise, especially as the motor shifts between wash and spin modes Belt that has become glazed, hardened, or "slick" from years of use Visible cracking, fraying, or glazing on the belt surface General noise or vibration during the wash or spin cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP22003483 22003483, 22002709, 62618130, 824667, AP6006365, EAP11739438, WP22003483VP, AWP47150, PD00002551, PS11739438 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Maytag Atlantis top-load washers built on the Whirlpool platform, including model numbers such as: MAV4057AWQ, MAV4057AWW, MAV4500AWW MAV5000AWQ, MAV5000AWW, MAV5057AWQ, MAV5057AWW, MAV5960AWW MAV6000AWQ, MAV6000AWW, MAV6057AWQ, MAV6057AWW MAV6200AWQ, MAV6200AWW, MAV6250AWQ, MAV6250AWW, MAV6257AWQ, MAV6257AWW MAV6548AWQ, MAV6548AWW, MAV6601AWQ, MAV6601AWW, MAV6650AWW, MAV7000AWQ Note: Always verify your full model number before ordering, since Whirlpool and Maytag use different belt lengths and profiles across their washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drive belt — transmits motor power to spin the washer drum Resolves "pumps but won't spin," "won't agitate," "spins slowly," and "chirping/slipping noise" symptoms caused by belt wear 52 inches long, black rubber construction Rides on three pulleys to transfer motor rotation to the drive system Direct drop-in replacement matching the original length and profile Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667 Compatible with Maytag Atlantis top-load washers built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 22003483 OEM Part Number WP22003483 Part Type Washer Drive Belt Condition Aftermarket Replacement Application Maytag Atlantis Top-Load Washers (Whirlpool-Built) Length 52 inches Material Rubber Color Black Function Transmits motor rotation to the drive system to spin the drum Quantity 1 drive belt Compatible Brand Maytag (Whirlpool-built) Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the motor and belt area. Loosen the motor's mounting screws so the motor can be pushed toward the drum, releasing tension on the old belt. Slide the old belt off its three pulleys and remove it. Route the new 22003483 belt over the same three pulleys, matching the original path. With the belt in place, gently push the motor away from the drum by hand to apply tension, then tighten the motor's mounting screws while continuing to check belt tightness — the belt should have firm, even tension across all three pulleys with no excess slack. Reinstall the rear panel, restore power, and run a full test cycle through both agitate and spin to confirm smooth, quiet operation with no chirping or slipping. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My washer makes a chirping noise when it shifts from agitate to spin. Is that the belt? Yes, this is a documented symptom of a worn belt. One long-term owner traced this exact chirp to a 10-year-old belt that had become "slick" from age — smooth and hardened enough that it briefly slipped on the pulleys as the motor shifted between modes, rather than moving cleanly into position. Replacing the belt resolved the noise completely. My belt doesn't look cracked or damaged. Could it still be the problem? Yes. A belt can degrade in ways that aren't obvious at a glance — the rubber can harden and glaze over time, becoming slick and losing its grip on the pulleys even without visible cracking or fraying. If your washer is slipping, chirping, or spinning weakly and the belt has been in service for many years, age-related slickness is a reasonable explanation even if the belt still looks intact. How do I know if I have the right belt length for my washer? This belt is 52 inches long and specific to the Maytag Atlantis top-load platform. Whirlpool and Maytag use different belt lengths across other washer models, so always confirm your model number matches the compatibility list, or measure your old belt for comparison, before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, profile, and material of the original WP22003483 drive belt used in compatible Maytag Atlantis top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP21352320 Genuine OEM Whirlpool Washer Drive Belt The WP21352320 is a genuine Whirlpool OEM drive belt for Whirlpool top-load washers. This belt connects the drive motor to the transmission at the bottom of the washer, and it's what actually spins the basket during the wash and spin cycles. Unlike a dryer's drum belt, which simply tumbles a drum, this washer drive belt has to transfer real torque to spin a heavy, water-filled basket, which puts it under considerably more mechanical stress. Measuring approximately 51" long and 3/8" wide. A worn or broken belt produces a distinctive set of symptoms: the washer may not spin at all, spin only slowly, agitate poorly or not at all, fail to drain properly since the pump relies on the same drive system, or produce a burning smell or loud grinding noise as a worn belt slips against the pulley. One useful diagnostic tip worth knowing: a belt can look intact at a glance but still be worn out — if the sides of the belt appear shiny or glazed rather than matte, that's a sign of slippage-related wear even without a visible crack. It directly replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882. Quick Answer The WP21352320 Genuine OEM Whirlpool Washer Drive Belt fixes Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers with a drum that won't spin, spins slowly, won't agitate, won't drain, or produces a burning smell or loud grinding noise. Approximately 51" long, 3/8" wide. Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, PS11738882. A belt can look intact but still be worn out — check the sides for a shiny, glazed appearance, which indicates slippage wear even without a visible crack. Common Problems This Part Fixes Washer drum won't spin, or spins only slowly Washer won't agitate during the wash cycle Washer won't drain properly Burning smell coming from the washer during operation Loud grinding noise from underneath the washer Washer that shakes or moves excessively during spin Washer that won't start or stalls partway through a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP21352320, 21352320, 21001478, 35-2073, 35-2320, 35-3662, PD00002418, EAP11738882, AP6005822, AWP46532, PS11738882, WP21352320VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Whirlpool top-load washers, and also fits select Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, and Ikea washers built on the Whirlpool platform, including model numbers such as HAV3460AWW. Note: Always verify your full model number before ordering, since Whirlpool uses several different drive belts across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, width, and material Connects the drive motor to the transmission to spin the basket Resolves "won't spin," "won't agitate," "won't drain," "burning smell," and "grinding noise" symptoms caused by belt failure Approximately 51" long, 3/8" wide Direct drop-in replacement matching the original belt routing Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882 Compatible with Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP21352320 Part Type Washer Drive Belt Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Length Approx. 51 in. Width 3/8 in. Attaches To Motor pulley and transmission Repair Difficulty Medium — basic hand tools required Quantity 1 drive belt Compatible Brands Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, Ikea Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Consider The Motor Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker, and shut off both the hot and cold water supply valves before beginning. Pull the washer out from the wall for full access. Wear work gloves. Locate the drive belt around the motor at the bottom of the washer. Use a flathead screwdriver or hex wrench to remove the screws holding the motor bracket in place, which releases tension on the belt. Carefully slide the motor bracket off the motor, and use pliers if needed to work the old belt off the pulley. While the bottom of the washer is accessible, this is a good time to inspect the motor pulley for wear as well, since it's a related component you'll already have exposed. Install the new WP21352320 belt around the pulley and transmission, following the same routing as the old belt, and make sure it's seated securely and tightened properly — a loose or improperly seated belt will slip and wear out quickly. Reattach the motor bracket with its screws. Restore the water supply and power, then run a test cycle to confirm the washer spins, agitates, and drains normally with no unusual noise. Tools needed: multi-bit screwdriver, hex wrench, standard pliers, work gloves. Frequently Asked Questions My belt looks fine — no cracks or visible damage. Could it still need replacing? Yes, and this is a common source of confusion. A belt can appear intact with no cracks and still be worn out. Check the sides of the belt closely: if they look shiny or glazed rather than having a matte, textured surface, that glazing indicates the belt has been slipping against the pulley, which is a clear sign of wear even without visible cracking. My washer pumps and drains but the drum spins slowly or not at all. Is this the belt? Yes, this is one of the most direct symptoms of a worn or slipping drive belt. Since this belt is what actually transfers the motor's power to spin the basket, a worn belt can slip under load, causing slow or absent spinning even though the motor itself and the drain pump are both working normally. Should I replace the motor pulley at the same time? It's worth inspecting while you have the bottom of the washer accessible, even if you don't end up replacing it. A worn pulley can accelerate wear on a brand-new belt, so checking its condition during this repair is a reasonable precaution, especially if your old belt showed the glazed, slipping-related wear pattern. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and routing configuration of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP95405 Washer Drive Belt The Genuine OEM Whirlpool WP95405 is a washer drive belt, a looped rubber V-belt, 1/2 inch wide and 47-3/8 inches long, that runs between the motor pulley and the drive pulley. When the motor turns, the belt turns the drive pulley, which spins the basket and agitates the clothes. A worn, stretched, or damaged belt can cause squealing at the start of the spin cycle, thumping during spin, longer wash times, or poor cleaning. This is the original Whirlpool part. It is listed for Whirlpool-built washers sold as Whirlpool and Kenmore. Replacing a belt takes some work to access the drive, and belts differ between washer families, so check the part number against your model before ordering. Quick Answer The Genuine OEM WP95405 Drive Belt fixes a Whirlpool or Kenmore washer that squeals or thumps during spin, takes longer to wash, or doesn't spin or agitate properly because the belt is worn or loose. Classic symptom: a squeal when the spin cycle starts, or a basket that spins slowly or not at all while the motor runs. Common Problems This Part Fixes Squealing at the start of the spin cycle Thumping noise during spin Longer wash times or poor cleaning Basket spins slowly or doesn't spin although the motor runs Visibly worn, stretched, cracked, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part numbers: WP95405, 95405, 16192, 16358, 21012, 26000095405, 3480, 8201, 8X475, 91261, F341241, LB165, P50-047, AP6013662, AWP48936, EAP11746889, PD00002366, PS11746889 These numbers span several generations of Whirlpool's own part numbering for this belt. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for Whirlpool and Kenmore washers, including these examples: Whirlpool LA5700XKW0, 2LA5700XKW0, 3LA5700XKW0, LA5705XKW0, LA6800XPW1, LA3800XPW1 Kenmore 11082620, 11075601, 11075193, 11076529, 11080094, 11076065 Note: The models above are a sample, not a full list. Washer belts differ in length and profile between washer families, so check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool washer drive belt, 1/2" wide x 47-3/8" long V-shape, cog-tooth belt profile Connects the drive motor to the drive system so the basket turns Resolves squealing, thumping, and slow-spin problems caused by a worn belt Replaces many older Whirlpool belt numbers, including 95405 Fits Whirlpool and Kenmore washers Product Specifications Part Number WP95405 OEM Part Number WP95405 Part Type Washer Drive Belt Belt Size 1/2" Wide x 47-3/8" Long Belt Profile V-Belt, Cog (Notched) Tooth Condition Genuine OEM Application Whirlpool & Kenmore Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and drive pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves and tensioned as shown in your service guide before reassembling. Reviewers rate this repair from moderate to very difficult, taking roughly 1 to 2 hours or more. Frequently Asked Questions My washer squeals when the spin starts. Is this the part I need? A worn or loose drive belt is a common cause. One reviewer reports a squeal at the start of spin that went away after the belt was replaced and tightened. Is WP95405 the same as 95405? Yes. 95405 is the older Whirlpool number, and WP95405 is the current number. This belt also replaces the other older numbers in the Replaces list above. Is this an easy repair? It depends on your model. Reviewers rate it from moderate to very difficult, usually taking 1 to 2 hours or more, because the drive has to be reached and the belt reseated. Follow your model's service guide. Will this fit my washer? It is listed for many Whirlpool and Kenmore washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X24697 Washer Drive Belt The XPARTCO WH01X24697 is an aftermarket replacement drive belt for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This belt connects the drive motor to the drive system, transmitting rotation to spin the basket during the wash and spin cycles. Measures approximately 21" long, made of durable, flexible rubber engineered to reduce slipping and squeaking while withstanding regular tension and wear. Over time, the belt stretches, cracks, or breaks from age and normal use. If your washing machine is making unusual noise, not spinning correctly, or the basket isn't moving, this drive belt may be the cause. It directly replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Quick Answer The XPARTCO WH01X24697 Washer Drive Belt fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers with unusual noise, a basket that won't spin correctly, or a basket that isn't moving at all. Approximately 21" long. Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Not the same as the similarly-numbered WH01X24180 or WH01X27538 belts, which are separate parts used on other GE/Hotpoint models — confirm your exact part number before ordering. Common Problems This Part Fixes Basket not spinning or not moving at all Unusual noise during operation, including squeaking Basket slipping or spinning inconsistently Wash cycle running without proper agitation or spin Belt visibly stretched, cracked, or broken Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WH01X24697, 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as GTW220ACK1WW, GTW220ACK2WW, GTW220ACK3WW, GTW330ASK0WW, GTW330ASK1WW, GTW330ASK2WW, GTW460AMJ1WW, GTW460AMJ3WW, GTW460AMJ4WW, GTW460ASJ1WW, GTW460ASJ3WW, GTW460ASJ4WW, GTW460ASJ5WW, GTW460ASJ6WW, GTW460ASJ7WW, HTW200ASK0WW, HTW200ASK1WW, HTW200ASK2WW, HTW240ASK0WS, HTW240ASK1WS, and HTW240ASK2WS. Note — not the same as WH01X24180 or WH01X27538: These are separate GE/Hotpoint drive belts with their own cross-reference sets, used on different models. The similar numbering makes them easy to confuse. Always verify your exact part number before ordering. Contact our support team with your model number if you're unsure which belt your washer needs. Key Features Aftermarket replacement drive belt — connects the drive motor to the drive system to spin the basket Resolves "won't spin," "unusual noise," and "basket not moving" symptoms caused by belt failure Approximately 21" long Durable, flexible rubber construction engineered to reduce slipping and squeaking Direct drop-in replacement matching the original length and profile Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair with basic tools Product Specifications Part Number WH01X24697 OEM Part Number WH01X24697 Part Type Washer Drive Belt Condition Aftermarket Replacement Length Approx. 21" Material Rubber Function Connects the drive motor to the drive system to spin the basket Repair Difficulty Easy to Moderate Quantity 1 drive belt Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the washer using a socket wrench set, taking out the securing screws and carefully lifting the panel away. Locate the drive belt near the motor, at the bottom of the washer. Use a screwdriver to loosen the tensioner, then gently slide the old belt off the pulleys. Fit the new WH01X24697 belt around the pulleys in the same path as the old one, then re-tension it with the tensioner. Reinstall the back panel and secure its screws. Restore power and run a test cycle to confirm the basket spins smoothly with no unusual noise. Tools needed: socket wrench set, screwdriver, work gloves. Frequently Asked Questions My washer's basket isn't spinning. Is this the belt I need? Yes, this is one of the most common symptoms of a failed drive belt. Since this belt is what transmits rotation from the drive motor to the basket, a stretched, cracked, or broken belt can leave the motor running while the basket doesn't spin correctly or at all. Is this a difficult repair? No, it's a straightforward repair for a confident DIYer with basic tools. It involves removing the back panel to access the belt near the motor, loosening the tensioner, and swapping the belt — no specialized skills required. Is this the same as WH01X24180 or WH01X27538? No, these are separate GE/Hotpoint drive belts with their own distinct cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old belt rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the length, material, and pulley fit of the original WH01X24697 drive belt used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 134511600 Washer Drive Belt Replaces WH07X10009 The XPARTCO 134511600 is an aftermarket replacement washer drive belt (V-belt) compatible with a wide range of Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, and Kelvinator washing machines. The drive belt connects the drive motor to the washer's drive system, transferring power to spin the basket and drive the transmission during agitation and spin cycles. When the belt wears out, stretches, frays, or snaps, the washer motor runs but the tub doesn't spin or agitate — one of the most recognizable failure patterns in appliance repair. This is a universal-fit aftermarket belt that spans both the Frigidaire/Electrolux platform (134511600-series part numbers) and the GE platform (WH07X-series part numbers) — one physical belt covers both manufacturers' cross-referenced drive belt positions on compatible washers. V-belt profile, approximately 1/2" wide with a 31–32" circumference. It directly replaces 134511600, 134161100, 131686100, 131234000, 1156860, 145371, 3204418, F145371, F145371-000, AP3867042, AP3203734, AH1146950, EA1146950, PS1146950, PS960606, WH07X10009, WH07X10002, WH07X0113, WH7X10009, WH7X10002, WH7X113, AH960606, EA960606, and 1089279. Belt failures typically come from normal wear, stretching, fraying, or snapping due to overloading. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 134511600 Washer Drive Belt fixes Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, and White-Westinghouse washers where the motor runs but the tub won't spin or agitate, the washer makes squealing or burning-rubber smells, or the belt is visibly cracked, frayed, or snapped. V-belt, approximately 1/2" wide x 31–32" circumference. Universal-fit — spans both Frigidaire (134511600) and GE (WH07X10009) platforms. Replaces 134161100, 131686100, 131234000, 1156860, AP3867042, AP3203734, PS1146950, PS960606, WH07X10009, WH07X10002, WH7X113 and more. Common Problems This Part Fixes Washer motor runs but the tub won't spin — belt snapped or slipping Washer won't agitate — belt no longer driving the transmission Tub spins slowly or intermittently — belt worn, stretched, or glazed Loud squealing or screeching during the spin cycle — belt slipping on the pulleys Burning rubber smell during operation — belt slipping and overheating Belt visibly cracked, frayed, glazed, or stretched Belt broken completely — often found lying in the bottom of the cabinet Clothes coming out sopping wet because the spin cycle isn't working Washer stops mid-cycle when it should transition to spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This universal-fit washer drive belt directly replaces the following OEM and cross-reference part numbers across multiple brands: 134511600, 1156860, 131234000, 131686100, 134161100, 145371, 3204418, AH1146950, AP3867042, EA1146950, F145371, F145371-000, AFR14885, PD00000111, PS1146950, WH07X10009, WH07X0113, WH07X10002, WH7X10002, WH7X10009, WH7X113, AH960606, EA960606, AP3203734, PS960606. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit drive belt is compatible with select washing machines from the following brands: Frigidaire washers — FLEB43RGS3, FLEB8200FS0, FLGB43RGS1, FLSE72GCS8, FLSG72GCSA, FWS223RFS0, FWS777GHS0, FWS933FS0, FWX233RES4, FWX645LBS4, FWXB45RGS0, FEZ831AS2 and related models Electrolux washers — select models on the Frigidaire platform GE washers and washer/dryer combo units — select models (WH07X10009 cross-reference) Crosley washers — CLCE500FW0, CLCE500FW1, CLCE500FW2, CLCG500FW0, CLCG500FW1, CLCG500FW3 and related models Gibson washers — select models Kelvinator washers — select models Tappan washers — select models White-Westinghouse washers — select models Kenmore / Sears washers — select Frigidaire-built and GE-built models Hotpoint and RCA washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Universal-fit washer drive belt (V-belt) — replaces both Frigidaire/Electrolux (134511600-series) and GE (WH07X-series) OEM drive belts in a single aftermarket part Connects the drive motor to the washer's drive system, spinning the basket and driving the transmission Resolves "motor runs but tub won't spin," "won't agitate," "squealing," and "burning rubber smell" symptoms V-belt profile: approximately 1/2" wide with a 31–32" circumference Durable rubber construction engineered to resist stretching, cracking, and glazing under load Replaces 23+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE, and universal aftermarket catalogs Compatible with Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 134511600 Also Replaces (GE-side) WH07X10009 Part Type Washer Drive Belt (V-Belt) — Universal Fit Condition Aftermarket Replacement Application Washing Machines (Frigidaire and GE platforms) Belt Profile V-belt Width Approximately 1/2" Circumference Approximately 31–32" Material Rubber Also Known As V-Belt Compatible Brands Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, RCA Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect the washer from all utilities — unplug it from the outlet (or shut off the breaker) and turn off the hot and cold water supplies — before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the cabinet. Pull the washer away from the wall to give yourself room to work. Access the drive belt by removing the rear access panel or tilting/laying the washer to reach the underside — the specific procedure varies by model, so consult your appliance's service diagram. Photograph the belt routing before removing anything so you can match the path with the new belt. Remove any pieces of the old broken belt from around the motor pulley and the transmission/drive pulley, and clear out accumulated lint or debris. Inspect the pulleys while you're in there — if a pulley is rough, grooved, or wobbly, the new belt will wear out prematurely and the pulley should be addressed too. Route the new 134511600 belt around the drive motor pulley and the transmission pulley, following the same path as the original. Rotate the pulleys by hand a few full turns to confirm the belt seats correctly in the pulley grooves and rides smoothly without twisting or binding. Confirm proper belt tension — the belt should be snug with a small amount of deflection, not loose enough to slip or so tight that it stresses the bearings. Reinstall the access panel, restore water and power, and run a test cycle to confirm the tub agitates and spins normally. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, work gloves. Frequently Asked Questions My washer motor runs but the tub won't spin — is the belt the problem? Almost certainly, yes. When you can hear the motor running (a hum or whir) but the tub stays still or barely turns, the drive belt has almost always snapped, slipped off its pulleys, or worn to the point where it can't grip. A quick check: unplug the washer, open the cabinet, and look for a belt lying loose in the bottom — a snapped belt is unmistakable. If the belt is still on the pulleys but glazed, cracked, or stretched, it's slipping rather than driving and needs replacement. Other symptoms that point to the belt: a squealing noise during spin, or a burning-rubber smell from the belt slipping and overheating against the pulleys. Does this really fit both Frigidaire AND GE washers? Yes — this is a genuine cross-brand part. The same V-belt design serves as a direct replacement for both the Frigidaire/Electrolux 134511600-series and the GE WH07X-series drive belts, and the two OEM catalogs are cross-referenced to each other through the 134161100 number. The belts share the same V-profile, width (approximately 1/2"), and circumference (31–32"), allowing a single aftermarket belt to function correctly in both platforms. Compatible models span Frigidaire's FLEB/FLGB/FLSE/FLSG/FWS/FWX series, GE washers and washer/dryer combos, plus Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Kenmore, Hotpoint, and RCA models. Always verify your specific model number before ordering. What causes a washer drive belt to fail? The most common causes are normal wear and tear from continuous use, stretching over time (which reduces grip and causes slipping), fraying or cracking from age and repeated flexing, and snapping due to overloading the washer or improper installation. Chronic overloading is a big contributor — forcing the motor to drive an over-packed tub puts extreme stress on the belt. Belt failures can also be accelerated by a worn or seized pulley, which is why it's worth inspecting the motor and transmission pulleys whenever you replace the belt. If a pulley is rough, grooved, or wobbly, the new belt will wear out quickly against it. How tight should the new belt be? The belt should be snug in the pulley grooves with a small amount of deflection when you press on it — firm enough that it won't slip under load, but not so tight that it puts excess strain on the motor and transmission bearings. Most washers with a V-belt drive use a spring-loaded or adjustable motor mount to set tension automatically; if yours has an adjustment, follow your model's service specification. After installing, rotate the pulleys by hand a few full turns and confirm the belt tracks correctly in the grooves without twisting or riding up the sides. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire, Electrolux, or GE OEM part, but is manufactured from durable rubber to match the V-belt profile, dimensions (approximately 1/2" wide x 31–32" circumference), and drive function of the original 134511600 and WH07X10009 washer drive belts used across compatible Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304516132 Washer Drive Belt – Compatible with Frigidaire, Electrolux, and Kenmore Washers Product Description Keep your washer spinning smoothly with the XPARTCO 5304516132 Washer Drive Belt. This high-quality aftermarket replacement transfers power from the motor to the washer drum, enabling proper agitation and spin speed. A worn, stretched, or broken belt can cause slow spinning, loud noises, or the drum not turning at all. Replacing it with this durable XPARTCO belt restores reliable performance and efficient wash cycles. Replaces Part Numbers 5304516132, 12638000001161, 7PJE607, PD00055739, EAP12585162, 4839724, AP6339955, PS12585162. Compatibility This replacement drive belt fits select Frigidaire, Electrolux, and Kenmore front-load washers. Example compatible models include (but are not limited to): Frigidaire FAFW3801LW, Electrolux EWFLS70JSS0, and Kenmore 417.41122310. Always verify your washer's model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and performance at a lower cost ⚙️ Restores Drum Motion – Ensures proper spinning, agitation, and wash performance 💪 Durable Construction – Made with reinforced rubber for long-lasting tension 🛠️ Easy Installation – Designed for quick DIY replacement 🛡️ Fixes Common Issues – Solves slow spinning, no spin, squealing noises, or drum not turning 📐 Product Specification Part Number: 5304516132 Component Type: Washer Drive Belt Material: Reinforced rubber with tension-resistant cord Dimensions: Exact OEM-equivalent sizing for proper tension Mounting: Wraps around motor pulley and drum pulley Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver (depending on model) ⚠️ Safety First: Always unplug the washer before servicing to avoid electrical shock. Steps: Unplug the washer and remove the rear access panel. Locate the old drive belt and remove it from the motor and drum pulleys. Position the new XPARTCO 5304516132 belt around the drum pulley first. Stretch the belt onto the motor pulley while rotating the drum. Reinstall the back panel, restore power, and test wash/spin cycles. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth washer performance — Add to Cart Now for a dependable, affordable repair!

Read more less

WH01X24697 Washer Genuine OEM Drive Belt The WH01X24697 is a genuine GE OEM drive belt for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This belt connects the drive motor to the drive system, transmitting rotation to spin the basket during the wash and spin cycles. Measures approximately 21" long, made of durable, flexible rubber engineered to reduce slipping and squeaking while withstanding regular tension and wear. Over time, the belt stretches, cracks, or breaks from age and normal use. If your washing machine is making unusual noise, not spinning correctly, or the basket isn't moving, this drive belt may be the cause. It directly replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. As a genuine OEM part, the WH01X24697 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH01X24697 Washer Genuine OEM Drive Belt fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers with unusual noise, a basket that won't spin correctly, or a basket that isn't moving at all. Approximately 21" long. Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Not the same as the similarly-numbered WH01X24180 or WH01X27538 belts, which are separate parts used on other GE/Hotpoint models — confirm your exact part number before ordering. Common Problems This Part Fixes Basket not spinning or not moving at all Unusual noise during operation, including squeaking Basket slipping or spinning inconsistently Wash cycle running without proper agitation or spin Belt visibly stretched, cracked, or broken Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WH01X24697, 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as GTW220ACK1WW, GTW220ACK2WW, GTW220ACK3WW, GTW330ASK0WW, GTW330ASK1WW, GTW330ASK2WW, GTW460AMJ1WW, GTW460AMJ3WW, GTW460AMJ4WW, GTW460ASJ1WW, GTW460ASJ3WW, GTW460ASJ4WW, GTW460ASJ5WW, GTW460ASJ6WW, GTW460ASJ7WW, HTW200ASK0WW, HTW200ASK1WW, HTW200ASK2WW, HTW240ASK0WS, HTW240ASK1WS, and HTW240ASK2WS. Note — not the same as WH01X24180 or WH01X27538: These are separate GE/Hotpoint drive belts with their own cross-reference sets, used on different models. The similar numbering makes them easy to confuse. Always verify your exact part number before ordering. Contact our support team with your model number if you're unsure which belt your washer needs. Key Features Genuine GE OEM part — factory-specified length and construction Connects the drive motor to the drive system to spin the basket Resolves "won't spin," "unusual noise," and "basket not moving" symptoms caused by belt failure Approximately 21" long Durable, flexible rubber construction engineered to reduce slipping and squeaking Direct drop-in replacement matching the original length and profile Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair with basic tools Product Specifications Part Number WH01X24697 Part Type Washer Drive Belt Condition Genuine OEM Length Approx. 21" Material Rubber Function Connects the drive motor to the drive system to spin the basket Repair Difficulty Easy to Moderate Quantity 1 drive belt Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the washer using a socket wrench set, taking out the securing screws and carefully lifting the panel away. Locate the drive belt near the motor, at the bottom of the washer. Use a screwdriver to loosen the tensioner, then gently slide the old belt off the pulleys. Fit the new WH01X24697 belt around the pulleys in the same path as the old one, then re-tension it with the tensioner. Reinstall the back panel and secure its screws. Restore power and run a test cycle to confirm the basket spins smoothly with no unusual noise. Tools needed: socket wrench set, screwdriver, work gloves. Frequently Asked Questions My washer's basket isn't spinning. Is this the belt I need? Yes, this is one of the most common symptoms of a failed drive belt. Since this belt is what transmits rotation from the drive motor to the basket, a stretched, cracked, or broken belt can leave the motor running while the basket doesn't spin correctly or at all. Is this a difficult repair? No, it's a straightforward repair for a confident DIYer with basic tools. It involves removing the back panel to access the belt near the motor, loosening the tensioner, and swapping the belt — no specialized skills required. Is this the same as WH01X24180 or WH01X27538? No, these are separate GE/Hotpoint drive belts with their own distinct cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old belt rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original length, material, and pulley fit of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

134511600 Genuine OEM Frigidaire Washer Drive Belt The 134511600 is a Genuine OEM Frigidaire replacement washer drive belt compatible with a wide range of Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley top-load and laundry center washers — including the FLS, FWS, FLEB, GLWS, FEZ, FGZ, and related series. The drive belt is a wrapped V-style rubber belt that connects the motor pulley to the washer tub, transferring the motor's rotation to spin the basket during the wash and spin cycles. When the belt breaks, wears out, or stretches, the motor continues to run but the basket stops rotating — the washer fills with water and drains but does not agitate or spin, leaving clothes soaking wet. This is a Genuine OEM part manufactured by Frigidaire to factory specifications. The belt measures approximately 32-1/4" in length (30" inner circumference) x 1/2" wide x 5/16" high — a wrapped V-belt profile that seats on the motor pulley. It directly replaces 1156860, 131234000, 131686100, 134161100, 145371, 3204418, F145371, F145371-000, AP3867042, AH1146950, EA1146950, EAP1146950, LB117, PD00000111, and PS1146950. Installs in 15–30 minutes with basic hand tools. Quick Answer The 134511600 Genuine OEM Frigidaire Washer Drive Belt fixes Frigidaire-platform top-load washers that won't agitate, won't spin, pump and drain but don't spin, make a burning rubber smell, or are noisy. Wrapped V-belt, approx. 32-1/4"L (30" inner circumference) x 1/2"W x 5/16"H, black rubber. Genuine OEM. Replaces 1156860, 131234000, 131686100, 134161100, 3204418, F145371, AP3867042, AH1146950, EA1146950, LB117, PS1146950. Compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley. Common Problems This Part Fixes Washer not agitating — belt has broken or slipped off the motor pulley Washer pumps and drains normally but does not spin clothes — belt failed Washer fills and drains but drum never moves — no belt drive to the basket Burning rubber smell during the wash or spin cycle — belt slipping on the motor pulley Squealing or grinding noise during operation — worn or slipping belt Washer spinning slowly or unevenly — stretched belt losing grip on the pulley Belt visibly cracked, frayed, broken, or missing inside the washer cabinet Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: 134511600, 1156860, 131234000, 131686100, 134161100, 145371, 3204418, AH1146950, EA1146950, F145371, F145371-000, AP3867042, PS1146950. Contact our support team with your model number if you need confirmation before ordering. Compatibility This washer drive belt is compatible with select top-load washers and laundry centers from the following brands and series: Frigidaire washers — FLS, FWS, FLEB, FEZ, FGZ, FLSG, GLWS, GLET, FWX, GWS series and related models Electrolux washers (select Frigidaire-platform models) Gibson washers (select models) Kelvinator washers (select models) Kenmore / Sears washers — 41 series and other Frigidaire/Electrolux-built models Tappan washers (select models) White-Westinghouse washers (select models) Crosley washers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance Wrapped V-belt style — connects the motor pulley to the washer tub to spin the basket during agitation and spin cycles Dimensions: approximately 32-1/4"L (30" inner circumference) x 1/2"W x 5/16"H Black rubber construction — designed to withstand continuous flexing and motor load under normal wash conditions Replaces 1156860, 131234000, 131686100, 134161100, 3204418, F145371, AP3867042, LB117, PS1146950, and additional cross-references Compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley washers DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 134511600 Part Type Washer Drive Belt (Wrapped V-Belt) Condition Genuine OEM Application Top-Load Washers and Laundry Centers Belt Style Wrapped V-belt Length (overall) Approximately 32-1/4 inches Inner Circumference Approximately 30 inches Width 1/2 inch Height 5/16 inch Material Rubber Color Black Quantity Sold individually (1 belt) Compatible Brands Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. On most compatible Frigidaire-platform washers, the drive belt is accessed by removing the back panel or by laying the washer on its side to access the motor and pulley from the bottom. The belt wraps around the motor pulley (small, at the motor shaft) and the transmission pulley or basket (large, beneath the tub). Release the old belt by slipping it off the motor pulley — the motor may need to be slightly unbolted and shifted to relieve tension, depending on your model. Route the new 134511600 belt around both pulleys in the same path as the original and seat it firmly in the V-groove on each pulley. If the motor position is adjustable, re-tension the belt so it deflects no more than 1/2 inch when pressed in the middle. Reinstall the back panel, restore power and water, and run a test cycle to confirm the basket agitates and spins normally. Tools needed: Phillips screwdriver, socket set or adjustable wrench. Frequently Asked Questions What does the washer drive belt do? The drive belt is the power transmission link between the motor and the washer basket. The motor turns a small drive pulley on its shaft, and the drive belt wraps around both the motor pulley and the larger transmission or basket pulley, transferring the motor's rotation to spin the basket. Without an intact, properly tensioned belt, the motor runs but the basket stays still — the washer fills with water, pumps it out, but never agitates or spins clothes. A broken, cracked, or slipping drive belt is one of the most common causes of washer failure on Frigidaire-platform top-load models. What is the difference between 134511600 and 1156860? These are the same drive belt. 1156860 is an older cross-reference part number and item number for the same belt that Frigidaire consolidated into the current part number 134511600. The 134161100, 131234000, 131686100, and 3204418 numbers are also cross-references for this same belt from various parts catalog revisions. All are covered by this OEM belt. My washer pumps but won't spin — is it the belt? A washer that pumps and drains normally but does not spin the basket is a classic drive belt failure symptom on Frigidaire-platform top-load washers. Since the drain pump is typically driven separately from the basket, a broken belt will stop basket rotation while leaving the pump functioning normally. Open the back panel and visually inspect the belt — if it is broken, stretched to the point of slipping, or missing entirely, replacing the 134511600 belt will restore normal spin and agitation. If the belt looks intact but the basket still doesn't turn, check the motor capacitor or idler pulley. Should I also inspect the idler pulley when replacing this belt? Yes — since the washer must be partially disassembled to replace the belt, this is a good opportunity to inspect the idler pulley for wear. The idler pulley maintains belt tension on compatible models — if the pulley bearing is worn or the spring tension is reduced, the belt will slip even when new, causing a burning rubber smell and poor spin performance. The Frigidaire washer idler pulley is sold separately (part 131462600 or 134371700 depending on model). If the idler pulley wobbles or the wheel doesn't spin freely by hand, replace it at the same time as the belt. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same drive belt installed in compatible Frigidaire, Electrolux, Gibson, and related brand top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X27538 Washer Drive Belt The XPARTCO WH01X27538 is an aftermarket replacement washer drive belt for GE and Hotpoint top-load washers. It is a 5-rib belt with 4 grooves, approximately 22.87 inches long. The belt connects the drive motor to the transmission pulley, so the motor can spin the basket and agitate the clothes. A worn, stretched, or broken belt can cause a washer that won't spin or agitate, a slow spin, squealing, or noise during the cycle. This is a direct-fit aftermarket replacement for the original GE belt. Belts differ between washer families, so check the part number against your model before ordering. Quick Answer The XPARTCO WH01X27538 Drive Belt fixes a GE or Hotpoint top-load washer that won't spin or agitate, spins slowly, or squeals or makes noise because the drive belt is worn or broken. Classic symptom: the motor runs, but the basket or agitator doesn't turn. Common Problems This Part Fixes Motor runs but the basket or agitator doesn't turn Washer won't spin or agitate Slow spin or poor wash performance Squealing or noise during the cycle Visibly worn, cracked, stretched, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part number: WH01X27538, 290D1101P005, 4587903, AGE25699, AP6328256, OEM18984777, PD00043350, PS12299369 Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for GE and Hotpoint top-load washers, including these examples: GE GTW220ACK4WW, GTW220ACK5WW, GTW330ASK4WW, GTW335ASN1WW GE GTW460ASJ8WW, GTW460ASJ9WW, GTW460ASJAWW Hotpoint HTW200ASK3WW, HTW240ASK5WS, HTW240ASK6WS Note: The models above are a small sample, not a full list. Washer belts differ between families, so compare your old belt to this one (approximately 22.87 inches, 5 ribs) and check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket drive belt for GE and Hotpoint top-load washers 5-rib, 4-groove design, approximately 22.87 inches long Connects the drive motor to the transmission pulley Resolves no-spin, no-agitate, and noise problems caused by a worn belt Typically a 30 minute to 1 hour repair Product Specifications Part Number XPWH01X27538 OEM Part Number WH01X27538 Part Type Washer Drive Belt Condition Aftermarket Replacement Belt Length Approx. 22.87 Inches Belt Profile 5-Rib, 4-Groove Application GE & Hotpoint Top-Load Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves before reassembling. Frequently Asked Questions My washer motor runs but the basket won't turn. Is this the part I need? A broken or slipping drive belt is a common cause. If the belt looks worn, cracked, or loose, replacing it is a good first step. How long is this belt? It is approximately 22.87 inches long, with 5 ribs and 4 grooves. If your old belt is a very different length or has a different number of ribs, check your model number before ordering. Is this a top-load or front-load part? It is listed for GE and Hotpoint top-load washers. If you are unsure which belt your washer uses, check your model number or contact our support team. Is this an easy repair? Retailers list it at roughly 30 minutes to 1 hour, though it depends on your model. Follow your model's service guide to reach the motor and pulleys. Will this fit my washer? It is listed for many GE and Hotpoint washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

 XPARTCO WE12X27300 Washer Drive Belt The XPARTCO WE12X27300 is an aftermarket replacement washer drive belt for GE stacked laundry center (combination washer/dryer) units, and also fits select Whirlpool, Amana, Hotpoint, Haier, and Kenmore combo models. This belt connects the motor pulley to the washer's drive system, transmitting rotation to spin the basket during agitation and spin cycles. Made of neoprene rubber for corrosion resistance, low temperature resistance, wear resistance, and stability. Measures approximately 23" long, 0.5" wide, and 0.12" thick. Over time, the belt stretches, cracks, or wears through from age and regular use. Symptoms of a failing belt include the washer spinning extremely slowly, the washer failing to agitate, excessive noise during operation, or complete belt failure leaving the basket unable to move at all. It directly replaces 4587578, AP6328196, PS12342956, EAP12342956, FIX12342956, 253C1275P001, 5PJ587, 5PJ587SJ161, WE12X27300-50PK, AGE25036, and PD00054473. Quick Answer The XPARTCO WE12X27300 Washer Drive Belt fixes GE, Whirlpool, Amana, Hotpoint, Haier, and Kenmore stacked laundry center units where the washer spins extremely slowly, won't agitate, or makes excessive noise. Neoprene rubber, approx. 23" long, 0.5" wide, 0.12" thick. Replaces 4587578, AP6328196, PS12342956, EAP12342956, FIX12342956, 253C1275P001, 5PJ587SJ161, WE12X27300-50PK, AGE25036, PD00054473. This is a laundry center (combo unit) belt — a different application from a standalone washer belt. Since a worn belt sometimes runs alongside a failing speed sensor, it's worth checking that component too if the belt has clearly worn out. Common Problems This Part Fixes Washer spinning extremely slowly Washer failing to agitate Excessive noise during operation Belt completely failed — basket not moving at all Inconsistent or jerky basket movement Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WE12X27300, 253C1275P001, 4587578, 5PJ587, 5PJ 587 SJ161, 5PJ587SJ161, AGE25036, AP6328196, EAP12342956, FIX12342956, PD00054473, PS12342956 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This washer drive belt is compatible with select GE stacked laundry center units, and also fits select Whirlpool, Amana, Hotpoint, Haier, and Kenmore combo units built on the same platform, including model numbers such as GUD24ESSM0WW, GUD24ESSM1WW, GUD27ESSM0WW, GUV27ESSM0WW, GUV27ESSM1WW, GUD24GSSM0WW, GUD24GSSM1WW, GUD27GSSM0WW, GUD27GSSM1WW, GUD27GSSM2WW, GUD27ESPM0DG, GUD27ESPM1DG, GUD27GSPM0DG, GUD27GSPM1DG, GUD27EESN0WW, and GUD27GESN0WW. Note: This is a laundry center (stacked washer/dryer combo) belt, distinct from standalone GE washer belts like WH01X24180 or WH01X24697. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement washer drive belt for laundry center (combo) units Resolves "spins extremely slowly," "won't agitate," and "excessive noise" symptoms caused by belt failure Neoprene rubber — corrosion resistant, low temperature resistant, wear resistant Approximately 23" long, 0.5" wide, 0.12" thick Direct drop-in replacement matching the original length and profile Replaces 4587578, AP6328196, PS12342956, EAP12342956, FIX12342956, 253C1275P001, 5PJ587SJ161, WE12X27300-50PK, AGE25036, and PD00054473 Compatible with GE, Whirlpool, Amana, Hotpoint, Haier, and Kenmore laundry center units Aftermarket replacement built to OEM-equivalent quality standards Typical repair takes 0 to 15 minutes Product Specifications Part Number WE12X27300 OEM Part Number WE12X27300 Part Type Laundry Center Washer Drive Belt Condition Aftermarket Replacement Application Stacked Washer/Dryer Laundry Centers Material Neoprene rubber Length Approx. 23" Width Approx. 0.5" Thickness Approx. 0.12" Repair Difficulty Easy — 0 to 15 minutes Quantity 1 drive belt Compatible Brands GE, Whirlpool, Amana, Hotpoint, Haier, Kenmore Installation Notes ⚠️ Unplug The Laundry Center Before Starting Disconnect power to the laundry center unit at the outlet before beginning. Wear work gloves. Access the washer's drive belt through the appropriate access panel for your model — since this is a combined washer/dryer unit, take care to work only in the washer section. Locate the old belt connecting the motor pulley to the drive system. Slide the old belt off the pulleys. Fit the new WE12X27300 belt around the pulleys in the same path as the old one, making sure it seats correctly and is properly tensioned. Reassemble the access panel. Restore power and run a test cycle to confirm the washer agitates and spins normally with no excessive noise. Tools needed: basic hand tools, work gloves. Frequently Asked Questions My laundry center's washer spins very slowly. Is this the belt I need? Yes, this is a documented symptom of a worn drive belt. As the belt stretches or wears down, it can no longer grip the pulleys effectively, resulting in a noticeably slower spin than normal, along with possible noise or agitation problems. Should I check anything else while I'm replacing this belt? It's worth checking the speed sensor if your unit has one. One customer specifically noted they were replacing their speed sensor and noticed the belt was also worn, so they replaced both at the same time — a worn belt and a failing speed sensor can sometimes develop around the same time on the same unit. Is this the same as a standalone GE washer belt? No, this belt is specifically for GE-style stacked laundry center units, where the washer and dryer are combined into one appliance. It's a different part from standalone GE washer belts, such as WH01X24180 or WH01X24697, used on separate washing machines. Confirm your unit type and model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the length, width, thickness, and material of the original WE12X27300 drive belt used in compatible GE, Whirlpool, Amana, Hotpoint, Haier, and Kenmore laundry center units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less