Search results for "washer strike"

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO MFG63099101 Washer Door Strike (Door Lock Hook) The XPARTCO MFG63099101 is an aftermarket replacement washer door strike — also called a door lock hook or door latch hook — compatible with a wide range of LG front-load washers and Kenmore 796-series washing machines. The door strike is the metal hook component mounted on the inside edge of the washer door. When the door closes, the hook enters the door lock switch on the front panel and engages the electromagnetic lock mechanism, signaling the control board that the door is closed and locking it for safe operation during wash and spin cycles. Without an intact door strike, the lock can't grip anything, and the washer will not start. When the strike breaks — typically from repeated use, sudden impact, or stress over thousands of door cycles — the washer will not start, may stop mid-cycle, may display DE1 or DE2 error codes, leak water around the door, or fail to lock altogether. It directly replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132. Important: replacing the strike requires removing the inside door panel to access the hook — note that the inner glass insert is loose during disassembly and must be handled carefully. Often replaced alongside the matching door lock switch (EBF61315802, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO MFG63099101 Washer Door Strike fixes LG and Kenmore 796-series front-load washers where the door won't lock, won't start, stops mid-cycle, displays DE1 or DE2 errors, or leaks at the door. Metal hook attaches to the inside of the washer door — engages the lock switch when the door closes. Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132. Often paired with the door lock switch (EBF61315802, sold separately). Common Problems This Part Fixes Washer door not latching properly — strike broken or worn down Washer not starting because the door isn't detected as locked Washer stopping mid-cycle due to a door fault DE1 or DE2 error codes displayed on the control panel Minor water drips or leaks around the door during operation — door not sealing because the strike isn't fully engaging Door strike visibly broken, chipped, or missing on the inside edge of the door Door not staying closed — strike worn from repeated impact Washer not powering on Replaces Part Numbers This washer door strike directly replaces the following OEM and cross-reference part numbers: MFG63099101, 2759645, AGF77417823, PD00046132, EAP8752721, AP5787149, PS8752721. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the number printed on your original door hook may be a production batch code rather than the OEM part number — this does not affect fit. Compatibility This door strike is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3170CW/00, WM3180CW series LG front-load washers — WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HVA/01, WM3370HWA, WM3370HWA/01, WM3370HWA/00 series LG front-load washers — WM3400CW, WM3500CW, WM3500CW/00, WM3555HWA, WM3555HWA/00 series LG front-load washers — WM3570HVA, WM3570HVA/00, WM3575CW series LG front-load washers — WM3600HVA, WM3600HWA, WM3600HWA/00, WM3670HRA, WM3670HRA/00, WM3670HVA, WM3670HWA series LG front-load washers — WM3700HVA, WM3700HWA, WM3770HVA, WM3770HWA series LG front-load washers — WM3900HBA, WM3900HWA series LG front-load washers — WM4000HBA, WM4000HWA, WM4270HVA, WM4270HVA/00, WM4370HKA, WM4370HWA series Kenmore / Sears washers — 796-series (79641162410, 79641162411, 79641262610, 79641283310, 79641283311, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641482410, 79641482411, 79641483410, 79641483411, 79641582410, 79641582411, 79641583211, 79641583410, 79641583411, 79641962610, 79641963610 and many related models) Note: If both the door strike (MFG63099101) and the door lock switch (EBF61315802) have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new strike. Always verify your model number before ordering. Key Features Metal door strike (door lock hook) — mounts to the inside edge of the washer door and engages the door lock switch when the door closes Resolves DE1 and DE2 error codes when caused by a broken door strike on compatible LG and Kenmore washers Restores the proper engagement between the door and latch assembly for a firm, consistent connection every cycle Durable metal construction — designed to withstand repeated opening and closing impact Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132 Compatible with LG WM1388, WM3050, WM3170, WM3270, WM3370, WM3500, WM3570, WM3600, WM3670, WM3700, WM3770, WM3900, WM4000, WM4270, WM4370 series and Kenmore 796-series front-load washers Often replaced together with the door lock switch (EBF61315802, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number MFG63099101 Part Type Washer Door Strike (Door Lock Hook / Latch Hook) Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore LG-built platform) Location Inside edge of washer door Material Metal Often Paired With Door Lock Switch (EBF61315802, sold separately) Error Codes Resolved DE1, DE2 (when caused by broken strike) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Don't Drop the Inner Glass Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a broken strike, use a putty knife to pry the white latch on the door lock through the bottom service opening to release the door. With the door open, locate the screws around the perimeter of the inner door panel. Remove the screws to release the inner door panel from the outer frame. Important: the inner glass insert is loose once the panel is unscrewed — support the glass with one hand as you pry the panel away to prevent it from falling out and breaking. Note the orientation of the old door strike (the direction it points and how it's seated). Use needle-nose pliers or tweezers to pull out the retaining pin holding the old strike in place, then remove the broken strike. Install the new MFG63099101 strike in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Reinsert the retaining pin to secure it. Carefully reposition the glass insert into the door, reinstall the inner door panel, and tighten the screws. Restore power and run a test cycle to confirm the door locks properly and there are no leaks. Tools needed: Phillips screwdriver, needle-nose pliers or tweezers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door strike and the door lock switch? These are two separate parts that work together to lock the washer door. The door strike (MFG63099101) is the metal hook attached to the inside edge of the washer door — when the door closes, the hook is what physically enters the lock assembly. The door lock switch (EBF61315802) is the assembly mounted on the front panel just inside the door opening — it contains the electromagnetic mechanism that grips and locks the strike, and the electrical sensor that tells the control board the door is closed. If the strike is broken, the lock has nothing to grip and the washer won't start. If the switch is broken, the strike can still enter the slot but the lock won't engage or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing strike has broken off inside the lock or the lock won't release, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the strike installation. Always disconnect power from the washer first. The number on my old strike doesn't match — is it still compatible? In many cases, yes. LG sometimes prints production batch codes on door strikes that look like part numbers but don't match the official OEM part number. As long as your washer's parts diagram lists MFG63099101 (or one of its cross-references: AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132), this strike is the correct fit. If you're unsure, contact our support team with your washer model number and we'll verify before you order. Should I replace the door lock switch (EBF61315802) at the same time? Not always, but often. The strike and the lock switch work together as a pair — if one is worn, the other has typically experienced the same load over thousands of cycles and is approaching the end of its service life. When a broken strike is the cause of the failure, examine the lock switch when the panel is open: if the lock mechanism shows visible wear, doesn't grip the new strike firmly, or has corroded contacts, replace it at the same time. Since the door is already partially disassembled and you have the washer apart, doing both at once saves a second repair session. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal to match the dimensions, mounting configuration, and lock-engagement function of the original MFG63099101 door strike used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11457841 Washer Lid Latch Strike The XPARTCO W11457841 is an aftermarket replacement washer lid latch strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid latch strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the latch strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid latch strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. This W11457841 aftermarket replacement is built to OEM-equivalent specifications and supersedes the earlier W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The XPARTCO W11457841 Washer Lid Latch Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic latch strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid latch strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid latch strike visibly broken, cracked, or missing on the underside of the lid Latch strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid latch strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid latch strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Aftermarket replacement built to OEM-equivalent quality standards — direct fit for compatible Whirlpool platform washers Plastic latch strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Latch Strike Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid latch strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old latch strike: rotate it counterclockwise until the retaining tab breaks free and pulls back, then pull the old latch strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the latch strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid latch strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid latch strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current part number that superseded it. Both are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this aftermarket part covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid latch strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the latch strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the latch strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid latch strike uses a twist-in design with no screws or hardware. To remove the old latch strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, twist-in mounting design, and lid switch activation function of the original W11457841 lid latch strike used in compatible Whirlpool, Maytag, and Kenmore HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10240513 Washer Lid Lock Strike – Replaces WPW10240513 – Compatible with Whirlpool, Maytag & Kenmore Washers Product Description Restore proper lid locking function with the W10240513 Washer Lid Lock Strike. This replacement part attaches to the washer lid and engages with the lid lock assembly to ensure the washer detects when the lid is closed and can safely begin operation. A damaged or broken lid strike can prevent the washer from starting, cause lid lock errors, or stop the spin cycle. Replacing it with this durable replacement part restores proper lid engagement and ensures smooth washer operation. This part is designed to match original fit and function for reliable performance. Replaces Part Numbers WPW10240513, W10240513, AWP50167, PD00004624, 1873013, 045900191755, EAP11750882, AP6017583, PS11750882. Compatibility This replacement washer lid lock strike fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, and Roper washers. Common compatible models include (but are not limited to): Whirlpool WTW5000DW Maytag MVWC565FW Kenmore 110.22352510 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Direct Replacement Part – Matches OEM fit and function 🔒 Ensures Proper Lid Lock Engagement – Works with lid lock assembly ⚙️ Fixes Common Issues – Resolves lid lock errors and start failures 🧩 Simple Installation – Attaches easily to washer lid 💰 Cost-Effective Repair – Affordable solution for lid lock problems ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: ❌ Washer will not start 🔒 Lid not locking properly ⚠️ Lid lock error codes 🔄 Cycle won’t begin or stops mid-cycle 🛑 Washer won’t spin Replacing this lid strike can restore proper lid locking and washer operation. 📐 Product Specification Part Number: W10240513 Component Type: Washer Lid Lock Strike Material: Durable molded plastic Application: Lid lock engagement system Mounting: Snap-in or screw-mounted (model dependent) Quality Level: Aftermarket replacement 🛠️ Installation Notes Tools Needed: Screwdriver (if required) ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Locate the lid strike on the washer lid. Remove the damaged strike. Install the new W10240513 strike in place. Ensure proper alignment with the lid lock assembly. Restore power and test operation. ⏱️ Time Required: Under 10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Replacement Parts 🔄 30-Day Return Policy Restore proper lid locking and washer performance — Add to Cart Now for a quick and easy fix!

Read more less

XPARTCO 131763302 Washer Door Striker The XPARTCO 131763302 is an aftermarket replacement washer door striker compatible with a wide range of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers — including the Frigidaire Affinity series and a broad set of GLTF, FAFW, FFFW, FFFS, ATF, ATFB, BLTF, CTF, CRTF, FCCW, FRFW, FTF, and FWFB models. The door striker (also called a door strike or door catch) attaches to the inside edge of the washer door and physically enters the lock mechanism on the front panel when the door closes. Once engaged, the strike is what the lock latches onto — and the strike also activates the door switch, signaling the control board that the door is safely closed and the washer can start. When the striker fails — typically by cracking, chipping, or breaking off from repeated door closures — the washer will not start, will not lock the door, may leak water, or may fail to advance past the fill phase. Gray/red plastic construction, approximately 2.6" x 1.3". This is the current production part number that supersedes many earlier revisions. It directly replaces 131763302, 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH2378364, AH890617, EA2378364, EA890617, PD00000164, PS2378364, and PS890617. Often replaced together with the matching door lock assembly (131763256, sold separately). Installs in under 5 minutes — no tools required beyond a Phillips screwdriver. Quick Answer The XPARTCO 131763302 Washer Door Striker fixes Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers where the door won't lock, won't start, won't close properly, leaks water, or won't fill. Gray/red plastic. Approx 2.6" x 1.3". Current production part — supersedes 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH890617, EA890617, PS890617, AH2378364, PS2378364. Often paired with the door lock assembly (131763256, sold separately). Common Problems This Part Fixes Washer door won't latch properly — striker broken or worn down Washer won't start because the door isn't detected as locked Washer door won't close — striker missing or damaged Washer door will not open at the end of the cycle — striker stuck inside the lock Washer pumps but won't spin — spin cycle blocked by broken striker Washer won't fill with water — fill cycle blocked by broken striker Water leaking around the door — door not fully sealing because striker isn't fully engaging Striker visibly broken, chipped, or missing on the inside edge of the door Door lock failure — actuator damaged Replaces Part Numbers This washer door striker directly replaces the following OEM and cross-reference part numbers: 131763302, 134456600, 131763300, 131763340, 134456602, 134456640, 1564512, AH2378364, EA2378364, EAP2378364, AP4508273, AFR14210, PD00000391, PS2378364. 131763302 is the current OEM production part superseding all listed earlier revisions. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door striker is compatible with select front-load washers from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW0-LW7, FAFW3511KW0-KW2, FAFW3801LW0/LW2/LW3/LW4/LW5, FAFW3921NW0/NW1, FAFW4011LW0, FAFW4221LW0) Frigidaire front-load washers — ATF6000ES0/ES1, ATF6000FS0/FS1/FS2, ATFB6000ES0/ES1, ATFB6000FS0, ATF7000FE0, ATFB7000ES0 series Frigidaire front-load washers — BLTF2940ES0-ES3, BLTF2940FS0/FS1, BLTF6100FS0 series Frigidaire front-load washers — FFFS5115PW0, FFFW4000QW0, FFFW5000QW0 series Frigidaire front-load washers — FRFW3700LW0, FCCW2000LS0, FCCW3000ES0/FS0/FS1/FS2/FS3/FS4 series Frigidaire front-load washers — FTF1040AS0, FTF1240FS0/FS1, BTF2140FS1, CRTF1240AS0, CRTR9300AS0, CTF140ES0, CTF140FS0/FS1/FS2 series Frigidaire front-load washers — GLTF1040/GLTF1240/GLTF1570/GLTF2940 series and related GLEH/GLGH models Frigidaire front-load washers — Additional 38712, 38802, 970L48022A0, 970L48422E0 and related legacy models Electrolux front-load washers — select models with the matching striker configuration Kenmore / Sears front-load washers — 4124182300/2301, 412180/181/182/183/184, 4129042992, 4129052991, 410032990, 410042990, 410052990, 4101400, 410410, 410411 and related Frigidaire-built models Crosley front-load washers — BTF1240ES0/ES1, BTF1240FS0 and related models Gibson front-load washers — select models Kelvinator, Tappan, Westinghouse front-load washers — select models Note: The door striker (131763302) and the door lock assembly (131763256) are two separate components that work together — the striker enters the lock, and the lock grips the striker. If both are worn or one has caused damage to the other, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new part. Always verify your model number before ordering. Key Features Washer door striker — mounts to the inside edge of the door and enters the lock mechanism when the door closes Activates the door switch to signal the control board that the door is safely closed and ready for the wash cycle Restores the proper engagement between the door and lock assembly for consistent locking every cycle Current OEM production part number — supersedes many earlier revisions (131763310, 131763300, 131763340, 134456600, and more) Gray and red plastic construction, approximately 2.6" x 1.3" Replaces 20+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE (WH10X10004), and universal aftermarket catalogs Compatible with Frigidaire Affinity series and a broad set of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers Often replaced together with the matching door lock assembly (131763256, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 5 minutes with a Phillips screwdriver Product Specifications Part Number XP131763302 Supersedes 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640 Part Type Washer Door Striker (Door Strike / Door Catch) Condition Aftermarket Replacement Application Front-Load Washers (Frigidaire platform) Dimensions Approximately 2.6" x 1.3" Color Gray / Red Material Plastic Mounting Location Inside edge of washer door Often Paired With Door Lock Assembly (131763256, sold separately) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer Before Starting — Quick Toolless Replacement Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, use a putty knife to release the manual override latch through the bottom service opening. Locate the old door striker on the inside edge of the washer door. It's typically secured by a single Phillips screw. Unscrew the mounting screw and remove the old striker. If the striker has broken off inside the lock mechanism on the front panel, remove any broken pieces from the lock before proceeding — leaving debris in the lock will damage the new striker and prevent proper engagement. Take the new 131763302 striker and align it with the mounting hole in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Secure the new striker with the Phillips mounting screw. Close the door and confirm the striker enters the lock slot smoothly. Restore power and run a test cycle to confirm the door locks properly and the washer starts. Tools needed: Phillips screwdriver, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door striker and the door lock assembly? These are two separate parts that work together as a system to lock the washer door. The door striker (131763302) is the plastic part attached to the inside edge of the washer door — when the door closes, the striker enters the lock. The door lock assembly (131763256) is the assembly mounted on the front panel just inside the door opening — it contains the latching mechanism that grips the striker and the electrical switch that tells the control board the door is closed. If the striker is broken, the lock has nothing to grip and the washer won't start. If the lock is broken, the striker can still enter the slot but the lock won't hold it or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. What is the difference between 131763302 and the older 131763310 or 131763300? All are the same door striker across production revisions. 131763300 was the original OEM part number, 131763310 and 131763340 were mid-generation revisions, and 131763302 is the current OEM production version. Frigidaire also uses 134456600, 134456602, and 134456640 as additional catalog references for the same part. All are physically and functionally interchangeable — if your washer's parts diagram shows any of these numbers, the 131763302 is the correct current replacement, and this listing covers all of them. My washer won't start and the door seems to close normally — could this be the striker? Yes, this is one of the most common symptoms of a failed door striker on Frigidaire-platform front-load washers. Even though the door appears to close, if the striker has cracked or worn down, it may not physically engage the lock or activate the door switch correctly. Visually inspect the striker on the inside edge of the door — if it's broken, missing, chipped, or its tab has worn down, replacement is straightforward. Also inspect the lock opening on the front panel: if there are broken plastic pieces inside from the old striker, they need to be removed before the new striker can seat properly. Do I really only need a Phillips screwdriver for this repair? Correct — the 131763302 striker is held in place by a single Phillips mounting screw on the inside edge of the washer door. Remove the old striker, install the new one in the same orientation, and tighten the screw. The whole replacement typically takes under 5 minutes once you have the new part in hand. Just make sure to install it in the correct direction — installing the striker backwards will prevent the lock from engaging when the door closes. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable plastic to match the dimensions (approximately 2.6" x 1.3"), mounting configuration, and lock-engagement function of the original 131763302 door striker used in compatible Frigidaire, Electrolux, Kenmore, Crosley, and related front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP8181651 Washer Genuine OEM Door Striker Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a Genuine part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation.

Read more less

XPARTCO 131763310 Washer Door Striker The XPARTCO 131763310 is an aftermarket replacement door striker (also called a door strike or door catch) compatible with select Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan front-load washers. The door striker is a small plastic tab mounted on the washer door that engages with the door lock assembly on the front of the washer when the door is closed — activating the door switch and allowing the washer to start, fill, and spin. When the striker breaks or wears down, the door will not properly activate the door lock, causing the washer not to start, not to fill, or to display a door-related error code. Made from durable white plastic, this striker measures approximately 1-1/4" L x 9/16" W x 2-9/16" H with approximately 2 inches between mounting holes (center to center). It directly replaces 131763300, 134456600, 1032664, LP3310, AP3580441, and several additional cross-reference numbers. Sold individually. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The XPARTCO 131763310 Washer Door Striker fixes Frigidaire-platform front-load washers where the door won't activate the door lock, the washer won't start, won't fill, leaks from the door, or shows a door-related error code. White plastic, approx. 1-1/4" L x 9/16" W x 2-9/16" H, ~2" between mounting holes. Sold individually. Phillips screwdriver only — installs in under 15 minutes. Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, and more. Common Problems This Part Fixes Washer door will not properly latch or activate the door lock when closed Washer will not start — door switch not being triggered by the striker Washer will not fill with water — door lock not engaged Washer will not spin — door lock fault preventing cycle completion Water leaking from the door area due to door not sealing properly Door-related error codes displayed on compatible models Broken, cracked, or missing door striker visible on the washer door Replaces Part Numbers This door striker directly replaces the following OEM and cross-reference part numbers: 131763310, 134456600, 131763302, 1032664, 131763300, AH890617, EA890617, AP3580441, PS890617, AFR14210, PD00000391, EAP2378364, AP4508273, PS2378364, WH10X10004, 824421, AH269392, EA269392, AP2621447, PS269392. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door striker is compatible with select front-load washers from the following brands: Frigidaire front-load washers (ATF, ATFB, BLTF, GLTF, LTF, FTF, FAFW, FRFW series and more) Kenmore / Sears front-load washers (select Frigidaire-built models) Electrolux front-load washers (select models) Crosley front-load washers (CFW, CLCE series) Gibson front-load washers (GTF series) White-Westinghouse front-load washers Kelvinator front-load washers Tappan front-load washers Note: The 131763310 (white) and 131763302 (gray) are interchangeable and functionally identical — the only difference is color. Either part will work as a replacement regardless of which color was originally installed. Key Features Engages with the door lock assembly to activate the door switch, allowing the washer to start, fill, and run Critical safety component — washer will not operate without a properly functioning door striker Durable white plastic construction — strong and wear-resistant for long service life Dimensions: approx. 1-1/4" L x 9/16" W x 2-9/16" H; ~2" between mounting holes (center to center) Sold individually — one striker per order Direct replacement for 131763300, 134456600, 1032664, and LP3310 Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver only Product Specifications Part Number 131763310 Part Type Washer Door Striker (Door Strike / Door Catch) Condition Aftermarket Replacement Application Front-Load Washers Dimensions Approx. 1-1/4" L x 9/16" W x 2-9/16" H Mounting Hole Spacing Approx. 2" center to center Color White Material Plastic Sold As Single striker Compatible Brands Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, Tappan Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. Open the washer door and locate the door striker — it is the small plastic tab mounted on the inside of the door, typically near the top or center of the door panel. Remove the two Phillips screws securing the old striker to the door. If the striker is broken, the screws may already be loose or missing. Align the new 131763310 striker with the mounting holes in the door and secure it with the two Phillips screws. Close the door to confirm it clicks firmly into the door lock assembly. Restore power and run a short cycle to verify the washer starts, fills, and runs normally. Tools needed: Phillips screwdriver only. Frequently Asked Questions What does the washer door striker do? The door striker is the small plastic tab on the washer door that engages with the door lock assembly mounted on the front of the washer when the door is closed. As the door closes, the striker pushes into the door lock, activating the door switch — a signal to the control board that the door is securely closed. The washer will not start, fill, or spin unless the door switch is activated by the striker. A broken or worn striker means the door lock is never properly engaged, so the washer appears to be in a constant "door open" state even when the door is physically shut. What is the difference between the 131763310 and 131763302 door strikers? Both are Frigidaire-platform door strikers, they are different color and interchangeable. The 131763310 is used on older Frigidaire front-load washer models (ATF, GLTF, FAFW series and others). The 131763302 is a gray color used on newer Frigidaire and Electrolux models. Always compare your existing striker's shape and dimensions to confirm, or contact our support team with your model number. Should I also replace the door lock assembly when replacing the striker? Not necessarily — in most cases the striker is the only part that needs replacement. The striker is a small plastic tab that takes repeated impact every time the door is closed, making it the most commonly worn part in the door latch system. The door lock assembly (131763202) is more durable and less prone to failure. Inspect the door lock for any cracks, burn marks, or a latch that does not spring back after pressing — if it appears damaged, replace it as well. If the lock looks intact, the 131763310 striker alone should resolve the issue. My washer door closes but the washer still won't start — is it the striker? It may be. If the striker is cracked, worn, or broken, it may appear to engage the door lock but not push far enough into the lock assembly to fully activate the door switch. In other cases, a fully intact striker may not be the cause — the door lock assembly itself (131763202) or the door latch on the frame side may also be the culprit. Visually inspect the striker first — if it is visibly broken, replace it. If it appears intact, the issue may be with the door lock assembly or wiring. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 131763310 door striker. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 8181651 Washer Door Striker  Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X20826 Washing Machine Shock Absorber The XPARTCO WH01X20826 is an aftermarket replacement shock absorber (damper) for GE front-load washers. The wash tub inside a front-load washer hangs suspended inside the cabinet, and a set of these shock absorbers is what controls that movement — dampening the tub's vibration and motion during spin so it doesn't bang against the cabinet or shake the whole machine. These washers typically use four shock absorbers working together around the tub, and this listing is for a single individual shock absorber. Over time the internal damping material in these shocks wears out, or the shock can physically separate from its mounting point — something that can also happen if the washer is moved or shifted without the tub properly secured first. Because all four shocks on a given washer are typically the same age and under the same stress, if one has failed the others are often not far behind — many technicians recommend ordering four of this same part and replacing the full set together as a preventative measure. A worn or detached shock absorber produces a very recognizable symptom: excessive vibration, shaking, or banging noise during the spin cycle, sometimes strong enough that the washer visibly moves or "walks" across the floor. It directly replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Quick Answer The XPARTCO WH01X20826 Washing Machine Shock Absorber fixes GE front-load washers (and select Hotpoint, Haier, Monogram, Café, and Kenmore models built on the GE platform) that vibrate, shake, or bang excessively during spin, or seem to "walk" across the floor. Sold as a single individual shock absorber. Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. These washers use four shock absorbers total — if one has failed, order four of this part to replace the full set, since they wear on the same schedule. Common Problems This Part Fixes Excessive vibration or shaking during the spin cycle Loud banging or knocking noise from inside the cabinet during spin Washer that seems to "walk" or move across the floor during operation Tub striking the cabinet frame or nearby panels Shock absorber that has visibly separated or detached from its mounting point Noise or vibration that started or worsened after the washer was moved or relocated Visible wear, cracking, or looseness in the shock absorber material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washing machine shock absorber directly replaces the following OEM and cross-reference part numbers: WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select GE front-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: GE uses several different shock absorber part numbers across its washer lineup, including separate parts such as WH01X10727 and WH03X29516 for other platforms. This WH01X20826 shock is specific to the front-load models listed above and is not interchangeable with those other GE shocks. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement shock absorber — dampens tub vibration and movement during spin Sold individually — order four to replace the full set on a typical front-load washer Resolves "excessive vibration," "banging or knocking noise," and "washer walking across the floor" symptoms caused by worn or detached shocks Durable plastic and rubber construction for long-term damping performance Direct drop-in replacement — no modification required Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Compatible with GE, Hotpoint, Haier, Monogram, Café, and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH01X20826 OEM Part Number WH01X20826 Part Type Washing Machine Shock Absorber (Damper) Condition Aftermarket Replacement Application GE Front-Load Washers Material Plastic and rubber Function Dampens tub vibration and movement during spin Typical Quantity Per Washer 4 (this listing is for 1 individual shock) Quantity 1 shock absorber Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Consider Replacing All Four Shocks Together Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shock absorbers typically requires removing the top and/or front panel of the washer to reach the tub suspension points — check your model's service diagram, since access varies. Photograph how each old shock absorber connects to the frame and the tub before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Disconnect the old shock absorber from its mounting point at both the frame and tub ends, and remove the mounting pin. Install the new shock absorber in the same position with its mounting pin, matching the original orientation. If you're only replacing one shock, be aware the remaining three original shocks are the same age and under the same stress — many technicians recommend ordering three more of this same part and replacing all four together to avoid reopening the washer again soon after. Once installed, gently rock the tub by hand to confirm even resistance at each corner before reassembling the panels. Restore power and run a full spin cycle to confirm the vibration, shaking, or banging noise has resolved. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I need to order more than one of these? This listing is for a single shock absorber, but GE front-load washers use four of them working together around the tub. If one has failed, it's strongly worth ordering four total and replacing the full set, since all four are typically the same age and have been under the same stress — replacing just one risks having to reopen the washer again soon after for the next one. My washer started shaking right after I moved it to a new spot. Is that related? Yes, this is a documented cause of shock absorber problems on this platform. If the tub wasn't properly secured or the washer was tilted significantly during a move, one or more shock absorbers can separate from their mounting point. Check that all four shocks are still properly connected at both ends before assuming a shock itself has failed — sometimes reseating a separated shock is all that's needed, though if it shows wear it's worth replacing regardless. How much vibration is normal, and how do I know it's actually the shocks? Some vibration during high-speed spin is normal, especially with an unbalanced load. But vibration strong enough to move the washer across the floor, or accompanied by a banging or knocking noise from inside the cabinet, points to a suspension problem rather than a simple unbalanced load. Try redistributing the laundry evenly in the drum and running the spin cycle again — if the shaking persists with a balanced load, inspect the shock absorbers for wear, cracking, or separation. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, mounting configuration, and damping performance of the original WH01X20826 shock absorber used in compatible GE, Hotpoint, Haier, Monogram, Café, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10404050 Genuine OEM Washer Lid Switch Assembly The W10404050 is a Genuine OEM replacement lid switch and latch assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge top-load washers. The lid switch is a critical safety component that detects when the washer lid is opened or closed. It sends a signal to the control board to allow the washer to fill, agitate, and spin when the lid is closed — and to immediately stop the spin cycle when the lid is opened, preventing contact with a moving drum. This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It features a 4-wire plug connection and includes two bezels (one white and one gray) to match different model color schemes. It directly replaces W10238287, W10744659, W10404050VP, AP5263307, and several additional cross-reference numbers. The companion lid strike (W10240513) is sold separately — inspect the strike on your lid for wear or damage and replace if needed. Installs in 20–30 minutes with basic hand tools. Quick Answer The W10404050 Genuine OEM Washer Lid Switch Assembly fixes top-load washers that won't start, won't spin, have a blinking lid lock light, or continue spinning with the lid open. 4-wire plug connection. Includes white and gray bezels. Replaces W10238287, W10744659, AP5263307, and more. Compatible with Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge washers. Lid strike W10240513 sold separately. Common Problems This Part Fixes Washer will not start — lid lock light blinks without locking Washer fills but will not agitate or spin Washer lid lock light continuously blinks and clicks without engaging Washer continues to spin with the lid open — safety mechanism not working Lid appears locked but washer will not proceed past sensing or fill cycle Washer stops mid-cycle and will not restart without opening and re-closing the lid Lid lock assembly visibly broken or latch no longer springs back after pressing Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10404050, 1938607, W10238287, W10404050VP, W10744659, EAP3497627, AWP41256, PD00003596, AH3497627, AP5263307, EA3497627, PS3497627. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands: Whirlpool top-load washers — Cabrio and WTW series (electronic top-load models) Maytag top-load washers — Centennial, Bravos X, and MVWC/MVWX series Kenmore / Sears top-load washers — 110 series and select others (Whirlpool-built) Amana top-load washers — NTW and ATW series KitchenAid top-load washers Roper top-load washers Admiral top-load washers — ATW series Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Norge top-load washers Note: The W10404050 is for electronic top-load washers with a 4-wire lid lock (Cabrio, Centennial, Bravos, and similar platforms). Older mechanical top-load washers use a different lid switch style. Verify your model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Critical safety component — stops the spin cycle when the lid is opened to prevent contact with a moving drum Signals the control board to allow filling, agitating, and spinning when the lid is properly closed and locked 4-wire plug connection — direct plug-in replacement on compatible models Includes two bezels (white and gray) to match different model color schemes Replaces W10238287, W10744659, W10404050VP, AP5263307, and more Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos X, Kenmore 110 series, and many more Lid strike W10240513 sold separately — inspect and replace if worn Product Specifications Part Number W10404050 Part Type Washer Lid Switch and Latch Assembly Condition Genuine OEM Application Electronic Top-Load Washers (4-wire lid lock) Connector 4-wire plug Color White (includes both white and gray bezels) Includes Lid switch assembly, white bezel, gray bezel Companion Part W10240513 Lid Strike (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. The lid switch assembly is mounted under the washer's top panel near the lid opening. To access it, insert a putty knife about 2 inches from each front corner of the top panel to release the spring clips and lift the top panel. Disconnect the 4-wire harness from the old lid switch assembly. Remove the mounting screws securing the assembly and lift it out. Install the new W10404050 assembly, secure with the mounting screws, and reconnect the 4-wire harness. Choose the appropriate bezel (white or gray) for your model and snap it into place. Lower the top panel until the clips engage. Restore power and run a test cycle to confirm the lid locks, the washer starts, and the spin cycle stops when the lid is opened. Tip: While the top panel is raised, inspect the lid strike (W10240513) on the lid for cracks or wear — if worn, replace it at the same time. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the washer lid switch do? The lid switch assembly serves two functions. First, it is a safety device — when the lid is opened during the spin cycle, the switch immediately cuts power to the spin motor to prevent contact with the moving drum. Second, it signals the control board that the lid is securely closed and locked, allowing the washer to proceed through the fill, agitate, and spin cycles. If the switch fails, the washer either won't start at all, or will fail to proceed past a specific cycle stage because the board cannot confirm the lid is closed. My lid lock light is blinking — does that mean the lid switch needs to be replaced? A blinking lid lock light is one of the most common symptoms of a failed W10404050 lid switch assembly. It typically means the lid lock mechanism is attempting to engage but failing — either because the switch is internally faulty or because the lid strike (W10240513) on the lid is broken and not triggering the switch properly. Inspect the lid strike first — if it is cracked or missing, replace it. If the strike looks intact and the lid lock still blinks without engaging, replace the W10404050 switch assembly. Should I also replace the lid strike (W10240513) at the same time? It depends on the condition of the strike. Open the lid and inspect the two plastic prongs on the underside of the lid that engage the W10404050 latch — this is the W10240513 lid strike. If the prongs are cracked, broken, or noticeably worn down, replace the strike at the same time as the switch assembly. Since the top panel is already lifted for the switch replacement, it is a good opportunity to inspect and replace the strike if needed, using only a Phillips screwdriver. What washers is the W10404050 compatible with? The W10404050 is used on Whirlpool Cabrio and WTW series electronic top-load washers, Maytag Centennial and Bravos X top-load washers, and Kenmore 110 series top-load washers, among others. It is specifically for electronic top-load models with a 4-wire lid lock — not for older mechanical top-load washers that use a simpler 2- or 3-wire lid switch. Verify your model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid switch and latch assembly installed in compatible washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

D510181 Genuine OEM Dryer Metal Door Strike - Compatible with Speed Queen, Alliance, Huebsch Product Description Secure your dryer door with the D510181 Genuine OEM Dryer Metal Door Strike. This Speed Queen-manufactured metal strike is designed as a replacement for select Speed Queen, Alliance, Huebsch, and other compatible dryers. It latches into the door catch when the dryer door is closed, ensuring a secure seal during operation. This part addresses issues like the door not closing properly or not staying closed, often caused by a worn or damaged strike. Note: Includes (1) metal door strike. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: D510181, 510181, 500039, 54661, H87020228, PD00041917, TU21401, AP6284686. Compatibility: Compatible with select dryer models, including but not limited to: Speed Queen: ADE3SRGS175TW01, ADE4BRGS175TW01, ADEE9BGS175TW01, KDEBXRGS175TW01 Alliance: JDEJEAGW303EW01, JDEJGAGW303EW01, JSGJEAGW303EW01 Huebsch: YDE3TRGS171CW01, YDE4BRGS171CW01 Econowash: CA025L, CA025N Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Speed Queen, Alliance, Huebsch, Econowash, and other dryers. 🔧 Specifications: Genuine OEM Speed Queen metal door strike, corrosion-resistant. 💪 Reliable Performance: Ensures secure door closure for safe and efficient drying. 🛠️ Easy Installation: Requires pliers; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves door not closing or staying closed issues. Product Specification Part Number: D510181 Component Type: Dryer door strike Material: Metal Additional Specs: Corrosion-resistant metal, designed for front panel attachment  Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a reliable fix!

Read more less