Appliance Parts

XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570 This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features 2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 2 kits per order (2 door catches and 2 strikes in total) Product Specifications Part Number EXP570 (2 Pack) OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike per Kit Quantity 2 Kits (2 Door Catches & 2 Strikes) Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EXP570 Dryer Door Latch Kit The XPARTCO EXP570 is an aftermarket replacement door catch and strike kit for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. Each kit includes 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. Each kit includes 1 door catch and 1 strike. Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570. This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features Aftermarket replacement dryer door latch kit with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 1 kit per order Product Specifications Part Number EXP570 OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike Quantity 1 Kit Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? Each kit includes 1 door catch and 1 strike. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO (2 Pack) EXP571 Dryer Door Catch The XPARTCO (2 Pack) EXP571 is a two-pack of aftermarket replacement door catches for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 2 door catches. Quick Answer The XPARTCO (2 Pack) EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 2 catches per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 2 door catches per order Product Specifications Part Number EXP571 (2 Pack) OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 2 Door Catches Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 2 door catches. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279838 Dryer Heating Element The XPARTCO 279838 is an aftermarket replacement heating element for Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. This part is often nicknamed the "shorty" because of its compact size compared to the larger, older Whirlpool element it replaced, part number 4391960 — the shorty design is used on dryers with the lint filter positioned on the top right near the control housing. Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. A quick way to check: a healthy element reads approximately 9 to 10 ohms across its terminals with a multimeter; a reading of no resistance (open circuit) confirms the element has failed. This element shares the same dryer platform as our WP3392519 thermal fuse and works alongside a cycling thermostat and high-limit thermostat in the same heating circuit — all commonly checked or replaced together when a dryer stops heating. It directly replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130. Quick Answer The XPARTCO 279838 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Also called the "shorty" element. Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, PS3343130. A healthy element reads approximately 9-10 ohms with a multimeter; if the dryer has no heat at all, also check the thermal fuse (such as our WP3392519 listing) before assuming the element is at fault — a blown fuse produces the identical symptom. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that reads no resistance (open circuit) on a multimeter continuity or ohms test Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: 279838, WP279837, 279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, AH334313, AP3094254, AWP39215, PD00002351, EA334313, OEM9282771, PS334313. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air dryers built on the same platform, including model numbers such as: LER5624DQ0, LER4634EQ2 NED4655EW, NED4600YQ1 WED4815EW, WED4800BQ1, WED49STBW1, WED8300SW0 MEDC465HW, MEDC215EW, MEDX655DW, MEDX655DW1 RED4640YQ1, AED4675YQ1, AED4475TQ1 EED4400WQ0 Kenmore 70, 80, 90, 300, 400, 500, and 600 Series Model 110 Note: This element fits Whirlpool-platform dryers with the lint filter positioned on the top right near the control housing. It is a compact "shorty" design and is not the same element as the larger, older 4391960 used on earlier Whirlpool dryers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil for effective, heat-and-abrasion-resistant heating Compact "shorty" design for dryers with the lint filter near the control housing Direct drop-in replacement — no modification required Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP279838 OEM Part Number 279838 Part Type Dryer Heating Element Assembly ("Shorty") Condition Aftermarket Replacement Coil Material Nickel-chromium Typical Resistance (Healthy Element) Approx. 9-10 ohms Legacy Predecessor 4391960 (larger, older design, not interchangeable) Related Components Cycling thermostat, high-limit thermostat, thermal fuse (see our WP3392519 listing) Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, Jenn-Air Installation Notes ⚠️ Unplug Dryer Before Starting — Test Resistance Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, inspect the old element visually for a break in the coil — sometimes you can see it directly, or feel it by gently wiggling each section of the coil. If nothing is visibly broken, test with a multimeter: place one probe on each terminal and look for a reading of approximately 9-10 ohms on a good element; no resistance at all confirms the element has failed. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 279838 assembly in the same position, reconnect the wire terminals, and secure the mounting hardware — if the original connection wire shows burning or damage, replace it as well rather than reusing a damaged connector. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions How do I test whether the element is actually bad? Start with a visual inspection — often you can see a break directly in the coil, or find it by gently wiggling each section to check for a loose or separated point. If nothing is visible, use a multimeter set to ohms and place one probe on each terminal. A good element typically reads approximately 9 to 10 ohms; a reading of no resistance at all (open circuit) confirms the element has failed and needs replacing. My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first, since a blown fuse produces the exact same "no heat at all" symptom as a failed heating element and is a cheaper, faster part to test and replace — our WP3392519 listing covers the thermal fuse used on this same dryer platform. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test. What's the difference between this "shorty" element and the older 4391960? Both are Whirlpool dryer heating elements, but this 279838 is a more compact design used on dryers with the lint filter positioned on the top right near the control housing, while 4391960 is the larger, older element used on earlier Whirlpool dryer platforms. They are not interchangeable, so confirm which style your dryer uses — checking your model number or comparing the physical size of your old element — before ordering. Should I check the connection wire while I'm replacing the element? Yes, it's worth a look. The wire connecting to the element terminals can occasionally show burning or damage if the element was arcing or overheating before it failed. If you notice any discoloration, melting, or damage on the connection wire, replace it along with the element rather than reusing a compromised connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the nickel-chromium coil composition, resistance rating, compact "shorty" form factor, and terminal configuration of the original 279838 heating element used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EXP571 Dryer Door Catch The XPARTCO EXP571 is an aftermarket replacement door catch for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 1 door catch. Quick Answer The XPARTCO EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 1 catch per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 1 door catch per order Product Specifications Part Number EXP571 OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 1 Door Catch Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 1 door catch. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR60X26866 Refrigerator Evaporator Fan Motor The XPARTCO WR60X26866 is an aftermarket replacement axial evaporator fan motor for the fresh food section of select GE French door refrigerators, including the CFE28, CFE29, CWE23, CYE22, CYE23, DFE28, DFE29, GFD28, GFE26, GFE27, GFE28, GFE29, GFS26, GFS28, GNE26, GNE29, GYE22, GYS22, PFD28, PFE28, PFE29, PWE23, PYD22, PYE22, PYE23, and ZWE23 series. The evaporator fan motor pulls air through the evaporator coils to remove heat from the circulating air inside the refrigerator. Without a functioning evaporator fan, the refrigerator compartment cannot maintain its target temperature even when the compressor and condenser are running normally — the cold air generated at the evaporator simply isn't being circulated to the food storage areas. The WR60X26866 is a DC motor rated at 13.6V DC, 0.16A, with a fan housing measuring 3-4/7"L x 2"W x 3-1/8"H, plus a multi-color wire harness and plug approximately 11-1/2" long. It includes the axial fan blade and harness as a complete assembly. It directly replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, and PS12172983. Important: if your refrigerator was built between May 2014 and March 2015 with serial range FF–HD, the unit's software must be updated before installing this fan motor — see FAQ below. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR60X26866 Refrigerator Evaporator Fan Motor fixes GE French door refrigerators where the fridge isn't cooling but the freezer is cold, the evaporator coils are frosted over, the ice maker isn't working due to insufficient cooling, or there's loud humming or grinding from the freezer area. Axial fan motor, 13.6V DC, 0.16A. Fan housing: 3-4/7"L x 2"W x 3-1/8"H; harness ~11-1/2"L. Replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, PS12172983. Note: May 2014 – Mar 2015 build refrigerators (serial range FF–HD) require a software update before installation. Common Problems This Part Fixes Refrigerator not cooling properly while the freezer remains cold — classic evaporator fan failure Freezer cold but fridge warm — fresh food compartment air not being circulated Frosty or frozen evaporator coils due to insufficient air circulation Ice maker failure caused by inadequate cooling in the compartment Loud humming, grinding, or buzzing noise from the freezer or fresh food compartment Refrigerator running continuously without reaching set temperature Fan blade not spinning freely or seized when checked by hand Multimeter shows no continuity through the motor windings Replaces Part Numbers This evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE French door refrigerators, including: GE refrigerators — CFE28, CFE29, CWE23, CYE22, CYE23 series (CFE28TP2MBS1, CFE28USHNSS, CWE23SP2MBS1, CYE22TP2MBS1 and related) GE refrigerators — DFE28, DFE29 series (DFE28JELCDS and related) GE refrigerators — GFD28, GFE26, GFE27, GFE28, GFE29 series (GFD28GBLBTS, GFE26GGHEBB and related) GE refrigerators — GFS26, GFS28, GNE26, GNE29 series GE refrigerators — GYE22, GYS22 series (GYE22HMKEES and related) GE refrigerators — PFD28, PFE28, PFE29 series (PFE28KELFDS and related) GE refrigerators — PWE23 series (PWE23KSKDSS and related) GE refrigerators — PYD22, PYE22, PYE23 series (PYE22KSKBSS and related) GE refrigerators — ZWE23 series and select related Café and Profile French door models Important — Software Update Requirement: If your GE refrigerator was manufactured between May 2014 and March 2015 with a serial number in the range FF–HD, the refrigerator's control software must be updated by GE factory service (or via Software Update Module WR98R882802) before installing this fan motor. Installing the new motor without the software update on these affected units may result in improper performance. Check your refrigerator's serial number plate before ordering. Key Features Axial evaporator fan motor for the fresh food section of GE French door refrigerators Pulls air through the evaporator coils to remove heat and circulate cold air through the refrigerator compartment DC motor — rated 13.6V DC, 0.16A — runs on DC voltage from the refrigerator control board Includes the axial fan blade and pre-attached multi-color wire harness with plug Fan housing dimensions: 3-4/7"L x 2"W x 3-1/8"H; harness and plug approximately 11-1/2" long Quiet operation — engineered to minimize hum and vibration in the refrigerator cabinet Plastic and metal construction, black housing with multi-color harness Replaces an extensive list of GE part numbers including WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, and additional cross-references Compatible with GE, GE Café, and GE Profile French door refrigerators in the CFE, CWE, CYE, DFE, GFD, GFE, GFS, GNE, GYE, GYS, PFD, PFE, PWE, PYD, PYE, and ZWE series Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR60X26866 Part Type Refrigerator Evaporator Fan Motor (Fresh Food / Axial) Condition Aftermarket Replacement Application GE French Door Refrigerators Voltage 13.6V DC Amperage 0.16A Fan Type Axial Fan Housing Dimensions 3-4/7"L x 2"W x 3-1/8"H Harness Length Approximately 11-1/2 inches Color Black housing with multi-color harness Material Plastic / Metal Includes Axial fan motor assembly with harness Software Update Required For May 2014 – Mar 2015 builds (serial range FF–HD) — use WR98R882802 Compatible Brands GE, GE Café, GE Profile Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor for the fresh food section is mounted on the back wall of the fresh food (refrigerator) compartment, behind an access panel. Take a photo of the existing fan position and wire harness routing before disconnecting. Remove the shelves and any internal components blocking access to the back wall, then remove the screws holding the rear access panel in place. Disconnect the fan motor's wire harness connector and remove the mounting screws securing the old motor. Note the fan blade orientation on the motor shaft. Install the new WR60X26866 motor assembly in the same position with the blade facing the same direction, reconnect the wiring harness, and reinstall the mounting screws and access panel. Replace the shelves and other internal components, restore power, and confirm the fan spins and the refrigerator cools properly. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My fridge is warm but my freezer is cold — is the evaporator fan motor the problem? Yes — this is one of the most recognizable symptoms of evaporator fan motor failure on GE French door refrigerators with a separate fresh food evaporator. The freezer side has its own cooling circuit and remains cold, while the fresh food side relies on this fan to circulate air across its evaporator coils. When the fan fails, the freezer continues working but the fresh food compartment loses its cold air supply, warming up while the freezer stays at temperature. If you also notice frost building up on the evaporator coils behind the back panel of the fresh food compartment, the fan failure is confirmed. What is the software update requirement for May 2014 – March 2015 refrigerators? GE issued a software update for certain refrigerators manufactured between May 2014 and March 2015 (serial range FF–HD) before they could properly support newer revisions of the WR60X26866 evaporator fan motor. If your refrigerator falls in this date and serial range, the control software must be updated before installing this fan motor — either by GE factory service or by using the Software Update Module part WR98R882802. Installing the new fan on an unupdated unit can result in improper performance. Check the serial number plate inside your refrigerator (typically on the left side wall) to confirm whether your unit is affected. Refrigerators built outside this range do not require the update. How do I test if the evaporator fan motor has failed? Unplug the refrigerator, then access the fan behind the rear panel of the fresh food compartment. First, try turning the fan blade by hand — if it doesn't spin freely, is stiff, or seizes, the motor bearing has failed. Next, listen during normal operation — if the motor is unusually noisy or makes a grinding sound, the bearings are worn even if it still spins. Finally, with the unit unplugged and the motor disconnected, use a multimeter on the motor windings to check for continuity. If the windings show no continuity, the motor has failed electrically. Also check for approximately 11–14V DC at the connector when the refrigerator is running — if voltage is present but the motor doesn't spin, the motor has failed. My fridge has two evaporator fans — which one does this replace? Some GE French door refrigerators have separate evaporator fan motors for the freezer and the fresh food sections. The WR60X26866 is the fresh food evaporator fan motor — it's the axial fan located behind the rear panel of the fresh food compartment, not in the freezer. If your symptom is "freezer cold, fridge warm," this is the correct part. If your symptom is "freezer warm" or "ice maker not making ice but fridge is fine," the freezer evaporator fan motor (a different part number) is more likely the cause. Confirm which compartment has the cooling problem before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, fan housing, electrical specifications, and pre-attached wire harness configuration of the original WR60X26866 evaporator fan motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

(5 Pack) 20A Ceramic Fuse 6.35 x 32 mm, 20A 250V - Compatible with GE, Whirlpool, Kenmore, Maytag, Frigidaire, LG, Samsung and Other Appliances Product Description Protect your appliances with the replacement 20A Slow-Blow Ceramic Fuse 6.35 x 32 mm, 20A 250V. This high-quality time-delay (slow-blow) ceramic cartridge fuse is designed for GE, Whirlpool, Kenmore, and other appliances like microwaves, washers, dryers, and spa control systems. With a ceramic body for durability and heat resistance, this fuse (6.35 x 32 mm, 20A, 250V AC) safeguards circuits from over current and short circuits while tolerating brief surges. It addresses issues like appliance failure, power loss, or blown fuses.  Note: Includes one ceramic fuse. Disconnect power before installation. Verify fuse size and rating match your appliance’s requirements. Replaces part numbers: EXP20A, MDA-20, 0326020.HXP, 0326020.MXDP, BK1-MDP-20-R, BK-MDP-V-20-R, GSA20, 8020.0605, 8020.0605.G, WB27X10388, AP3094537, AH334641, EA334641, EAP334641, PS334641, WP4375321, W11305892, W11305905, AP6009296, PS11742452, 3601-001198, AP4046006, PS4131369, 5F1CD2031S, AP4565040, 1206681, 4922155, WB27X11151, AP4980434, PS3486702, WB27X11151, AP4980434, PS3486702, WB2X3910, PS242167, AP2010811, WB2X3910, WB27X995, WB27X945, B27X10388, PS239525, AP2631556, WP8183507, 8183507, PS11745084, AP6011884, M0805101, AP6014669, PS11747931, WPM0805101, 5304423383, PS472662, AP2151673, EA472662, WB27X10928, AP3994062, WB27X10388, AH1481237, EA1481237, PS1481237, W11707984, W10138793, AP7225218, PS17629444, 3B74133Q, AP4440371, PS3522743, 5F1CD0202S, 5F1CD2031S, 3B74133K. AH3522741, EA3522741, AP4438152, PS3522741. Compatibility: Compatible with appliances including but not limited to: GE Microwaves: JE1860SH04, JVM1540SM5SS, JVM1440WH04 Whirlpool Microwaves: MH1150XMQ0, MH2175XSB0 Kenmore Microwaves: 721.62649200, 665.68612800 Whirlpool Washers: WTW5300SQ0, LSQ9544KQ0 Whirlpool Dryers: WED5300SQ0 Balboa Spa Control Systems: 30123 Other Brands: KitchenAid, Maytag, Amana, Hotpoint, and other appliances requiring 6.35 x 32 mm, 20A 250V slow-blow fuses Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Hotpoint, LG, Samsung and other appliances requiring 6.35 x 32 mm, 20A 250V fuses. 🔥 Specifications: replacement slow-blow ceramic fuse, 6.35 x 32 mm (1/4" x 1-1/4"), 20A, 250V AC, ceramic body, time-delay, 3.35–3.5 mOhms resistance, cylindrical, holder/clip mount. 💰 Cost-Effective Alternative: replacement fuse offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires insulated gloves, needle-nose pliers; typically installed in 5–15 minutes. 🛡️ Reliable Fixes: Resolves appliance failure, power loss, or blown fuse issues in microwaves, washers, dryers, and spa systems. Installation Notes: Safety First: Disconnect the appliance from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your appliances running safely and efficiently today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO EXPHV10 Microwave High Voltage Diode The XPARTCO EXPHV10 is a universal aftermarket replacement high voltage diode (rectifier) compatible with most major microwave brands including GE, Whirlpool, Maytag, Samsung, LG, Frigidaire, Panasonic, Sharp, KitchenAid, and Kenmore. The high voltage diode is a critical component in the microwave's high-voltage circuit, working alongside the high-voltage capacitor and transformer to convert alternating current (AC) to direct current (DC) — providing the high-voltage DC power required by the magnetron to generate microwave energy and heat food. When the diode fails — due to electrical surges, overheating, or normal wear — the magnetron cannot receive the correct power supply, resulting in a microwave that runs but does not heat. A failed diode may also cause the high-voltage fuse to blow repeatedly. Rated at 12,000V DC (12 kV) with a 500mA current capacity, the EXPHV10 is a universal cross-brand replacement that meets or exceeds OEM specifications across hundreds of microwave models. ⚡ HIGH VOLTAGE SAFETY WARNING — READ BEFORE SERVICING Microwaves contain a high-voltage capacitor that can store a lethal electrical charge of up to 2,100 volts even when the microwave is unplugged. Do NOT touch any internal components without first discharging the capacitor. If you are not experienced with high-voltage appliance repair, do not attempt this repair yourself — contact a qualified appliance technician. Always unplug the microwave before opening the cabinet and discharge the capacitor using a properly insulated discharge tool before handling any internal parts. Quick Answer The XPARTCO EXPHV10 Microwave High Voltage Diode fixes microwaves that run but produce no heat, have a repeatedly blown fuse, or have a humming sound with no heating. It converts AC to DC power for the magnetron and is rated 12,000V DC / 500mA. Universal fit — compatible with most GE, Whirlpool, Maytag, Samsung, LG, Frigidaire, Panasonic, Sharp, KitchenAid, and Kenmore microwaves. Common Problems This Part Fixes Microwave runs (turntable spins, light works) but does not heat food High-voltage fuse blows repeatedly after replacement Loud humming or buzzing sound with no heating Microwave takes much longer than normal to heat food Microwave heats unevenly or inconsistently Replaces Part Numbers This diode directly replaces the following OEM and cross-reference part numbers: HV10, EXPHV10, 2CL70, 2CL77, W11256462, W10886077, AWP43735, PD00047836, AP6784287, PS12584264, WB27X1160, AGE22195, PD00026293, AP2026385, PS239843, DE91-70063D, DE91-70063A, ASM94577, PD00033057, AP4236698, PS4235633, 5304417430, AP2151558, PS472334, 6021W3B001U, AP4439834, PS3528798, 6851W1A002E, ALG51731, PD00006373, AP5203812, PS3529603, 5304456178, AP3960683, PS1532581, 3518400800, AP7110292, 5304509479, 5304472472, AFR17769, PD00040522, AP4433625, PS12071314, WPR9800486, AWP128355, PD00004942, AP6014695, PS11747959, 11QBP0237, AP5633255, PS4085135, WB27X10744, AP3792899, PS953886, WB27X35382, WB27X10930, WB18X10449, WB27X10892, WB27X10965, WB27X11035, AP6992536, PS16219547, WB27X10562, AGE1037090, AP3187536, PS239704, WP13091701, AWP634588, PD00035043, AP6005641 PS11738693, WB27X10687, AGE1019656, PD00032466, AP3207509, PS953843, WB27X10107, AP2026017, PS239224, WB27X10037, AGE22509 PD00031660, AP2025948, PS239148, WPDE91-70063D, AWP547793, PD00034036, AP6014620, PS11747873, 6021W3B001V, 6021W3B001R, AP5632506 EAP3528799, ALG51931, PD00008859, AP4438526, PS3528799, WB27X21012, AGE360033, PD00037340, AP5791119, PS8754690, 00625682, 10001605, ABS11495, PD00047510, AP5804800, PS8770335, CL04-12. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal high voltage diode is compatible with most microwave ovens from the following brands: GE and Hotpoint microwaves Whirlpool microwaves Maytag microwaves KitchenAid microwaves Samsung microwaves LG microwaves Frigidaire and Electrolux microwaves Panasonic microwaves Sharp microwaves Kenmore / Sears microwaves Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Converts AC to DC power in the microwave's high-voltage circuit — enabling the magnetron to generate microwave energy and heat food Rated 12,000V DC (12 kV) / 500mA — meets or exceeds OEM electrical specifications Universal fit — compatible with most major microwave brands across hundreds of models Aftermarket replacement built to OEM-equivalent quality standards Pre-terminated leads — direct drop-in replacement, no modification required Compact insulated design for safe and easy installation Budget-friendly fix for one of the most common microwave no-heat failures Product Specifications Part Number EXPHV10 Part Type High Voltage Diode (Rectifier) Condition Aftermarket Replacement Application Microwave Oven High Voltage Circuit Voltage Rating 12,000V DC (12 kV) Current Rating 500 mA Material Insulated Epoxy Body Terminals Pre-terminated leads Fit Type Universal — fits most major microwave brands Compatible Brands GE, Whirlpool, Maytag, KitchenAid, Samsung, LG, Frigidaire, Panasonic, Sharp, Kenmore Installation Notes ⚡ DANGER — HIGH VOLTAGE — DISCHARGE CAPACITOR BEFORE SERVICING Microwaves store a lethal charge in the high-voltage capacitor even when unplugged. You must discharge the capacitor before touching any internal parts. Use a properly insulated discharge tool or resistor — never a screwdriver or bare wire. Once the capacitor is safely discharged: unplug the microwave and remove the outer cover. Locate the high voltage diode — it is connected between the high-voltage capacitor and the chassis ground. Disconnect both leads, note the orientation/polarity, remove the old diode, and install the new EXPHV10 in the same position and orientation. Reconnect leads, reassemble the cover, and test heating operation. Time required: approximately 20–25 minutes. If you are unsure about any step, contact a qualified appliance technician. Frequently Asked Questions Will the EXPHV10 fit my microwave? The EXPHV10 is a universal replacement diode compatible with most GE, Whirlpool, Maytag, KitchenAid, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwaves. Use the model search above to verify, or contact our support team before ordering. What does the high voltage diode do? The high voltage diode works with the capacitor and transformer to convert AC power to high-voltage DC power — typically around 4,000 to 5,000 volts. This DC voltage powers the magnetron, which generates the microwave energy that heats food. A failed diode prevents the magnetron from receiving proper power, resulting in a microwave that runs but does not heat. How do I test if my microwave diode is bad? After safely discharging the capacitor, use a multimeter set to the diode test mode. A good diode will show continuity in one direction and no continuity in the other (one-way electrical flow). A bad diode will show either no continuity in both directions (open) or continuity in both directions (shorted). A shorted diode will also cause the fuse to blow repeatedly. My microwave fuse keeps blowing — is the diode the problem? A shorted high voltage diode is one of the most common causes of a repeatedly blown microwave fuse. When the diode shorts, it draws excess current which blows the fuse. If you replace only the fuse and it blows again immediately, test the diode and capacitor as well before replacing the fuse again. Is this an OEM or aftermarket part? This is an aftermarket universal replacement part built to OEM-equivalent electrical specifications. It is not a genuine OEM part from any specific brand, but is rated at 12,000V DC / 500mA — meeting or exceeding the requirements of most microwave high-voltage circuits. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3387747 Dryer Heating Element Replaces WP3387747 The XPARTCO 3387747 is an aftermarket replacement heating element assembly for Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. Everything downstream — the drum temperature, the drying time, the final dampness of your clothes — depends on this coil working correctly. Rated 5400W at 240V, with two 5/16" terminals for a direct connection. The nickel-chromium coil is rated at roughly 85% nickel-chromium content for effective, heat-and-abrasion-resistant heating, and it's mounted in high-temperature ceramic insulators that hold it firmly in the frame so it won't loosen or shift under the vibration of a running dryer. Over years of use, the coil itself typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. It directly replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365. Quick Answer The XPARTCO 3387747 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. 5400W, 240V, two 5/16" terminals. Replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365. If the dryer has no heat at all, check the thermal fuse first — it's a cheaper, faster fix, and a blown fuse produces the same "no heat" symptom as a failed element. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that tests as an open circuit (no continuity) with a multimeter Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, KitchenAid, Amana, and Roper dryers built on the same platform, including model numbers such as: GEW9200LW0, GEW9200LW1, GEW9250PL0, GEW9250PW0, GEW9250PW1 GEQ9800PW1, GEQ9800PW2 MEDB835DW4, MEDC700VW0 WED5100HW1, WED5500XW1, WED5700AC1, WED6120HW1, WED6620HW1, WED8300SW2 MED5500FW1, MED6230HW1, MED6230RHW1 Kenmore 110.82822101 Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element assembly — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil (approx. 85% Ni-Cr content) for effective, heat-and-abrasion-resistant heating High-temperature ceramic insulators hold the coil firmly in the frame against vibration Rated 5400W at 240V Two 5/16" terminals for a direct connection Approximately 10"L x 6"W x 1"H Direct drop-in replacement — no modification required Replaces WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 3387747 OEM Part Number WP3387747 Part Type Dryer Heating Element Assembly Condition Aftermarket Replacement Wattage 5400 W Voltage 240V Terminals 2 (5/16") Coil Material Nickel-chromium (approx. 85% Ni-Cr) Insulators High-temperature ceramic Dimensions Approx. 10"L x 6"W x 1"H Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper Installation Notes ⚠️ Unplug Dryer Before Starting — Test Continuity Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, test the old element with a multimeter set to continuity — a healthy element reads continuous end to end, while a failed one (with a visible break in the coil) reads open. Photograph the wiring before disconnecting anything. Disconnect the two wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 3387747 assembly in the same position, reconnect the two wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first. A blown thermal fuse produces the exact same "no heat at all" symptom as a failed heating element, and it's a much cheaper, faster part to test and replace. Whirlpool's own service guidance recommends checking the thermal fuse before replacing the element. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test and likely replace. How can I tell if the element has actually failed? The most reliable way is a continuity test with a multimeter — set it to continuity mode, disconnect the element's wires, and touch a probe to each terminal. A healthy element shows continuity (a complete circuit); a failed one shows open (no continuity), which usually corresponds to a visible break or burned-through section somewhere in the coil if you inspect it closely. Why does the listing recommend cleaning the vent duct during this repair? Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the 5400W/240V electrical rating, nickel-chromium coil composition, ceramic insulator mounting, and terminal configuration of the original WP3387747 heating element used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP572 Dryer Door Catch – Aftermarket Replacement for Whirlpool, Kenmore, Maytag, GE, Hotpoint Product Overview This Door Catch is a replacement part for specific GE, Hotpoint dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly Replaces Part Numbers WE1M1011, PS3502777, AP5324728, WE01M0197, WE01X0889, WE01X0903, WE01X1032, WE1M187, WE1M197, WE1M536, WE1X1032, WE1X889, WE1X903. It provides a reliable fit and function similar to OEM components. Fixes the Following Issues Dryer door won’t stay closed Dryer doesn’t start Door pops open mid-cycle Worn or damaged door catch Compatible Brands Compatible with dryers made by Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, GE and Crosley. Suitable for many front-load and top-load residential models. Why Buy from Parts-O-Matic High-quality, durable replacement part Always Fast and Free U.S. shipping Easy to install – no special tools required Trusted by appliance repair professionals and DIYers

Read more less