Appliance Parts

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

197XP Dryer Thermostat Kit – Replaces 279816, WP3977767, W10900067 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Restore safe and efficient drying performance with the 197XP Dryer Thermostat Kit. This high-quality aftermarket replacement includes both a high-limit thermostat and a thermal cut-off fuse to regulate dryer temperature and prevent overheating. A failed thermostat or cut-off can cause long dry times, no-heat conditions, or overheating. Installing this complete kit ensures dependable temperature control and long-lasting dryer operation. Replaces Part Numbers 279816, 2651, 279816VP, 3399848, 3977393, AH334299, AP3094244, EA334299, PS334299, WP3977767, 3977767, 3399693, 898078, AP6009043, ER3977767, PS11742185, SET185, TJ90SET185, WP3977767VP, W10900067, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement thermostat kit fits select Whirlpool, Kenmore, Maytag, Amana, Roper, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.87562602, and Amana NED4655EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM temperature ratings and safety standards 🔥 Dual-Protection Design – Includes thermal cut-off fuse and high-limit thermostat for overheat prevention 💰 Affordable Alternative – Provides OEM-level performance at a lower cost 🛠️ Easy DIY Installation – Pre-terminated connectors and hardware for quick repair 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or short-cycling problems 📐 Product Specification Part Number: 197XP Temperature Ratings: 309* degree F Thermal Fuse with L250-80* degree F Limit Thermostat. High Limit Thermostat and Thermal Fuse for the Heater.      No need to splice any wires, no re wiring needed.  Component Type: Dryer Thermal Cut-Off & High-Limit Thermostat Kit Includes: Thermal cut-off fuse, high-limit thermostat, mounting hardware, and wire connectors Material: Metal thermostat housing with heat-resistant wiring Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the back panel of the dryer. Locate the heater housing and identify the existing thermostat and cut-off fuse. Remove wires and mounting screws from old components. Install the new 197XP thermostat kit in the same positions. Reconnect wires, reassemble the panel, and restore power. Run a drying cycle to confirm proper operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dryer and restore heat safely — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor The XPARTCO W10613606 is an aftermarket replacement compressor start relay and capacitor assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, and Magic Chef refrigerators. The start relay is a small but critical electrical component that plugs directly onto the compressor terminals and provides the initial power surge needed to start the compressor motor. Once the compressor reaches operating speed, the relay drops out — leaving the compressor to run on its own. The capacitor (rated 15µF ±5%, 250VAC) works alongside the relay to store and release the burst of electrical energy needed on startup. When the start relay fails, the compressor cannot start — causing the refrigerator to stop cooling entirely. A failed relay typically produces a clicking sound every few minutes as the compressor tries and fails to start, followed by a short rest, then another attempt. This kit includes both the start relay and the CBB61 capacitor. It directly replaces W10416065, 8208290, 8208368, C8931605, 67003186, 67005560, 67005561, 67005562, 67003764, 8171210, and several additional cross-reference numbers. Installs in under 15 minutes — no tools required in most cases. Quick Answer The XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor fixes refrigerators that are not cooling, are too warm, or are making a repeated clicking sound every few minutes as the compressor tries to start. Plugs directly onto the compressor terminals. Kit includes start relay and 15µF 250VAC CBB61 capacitor. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and more. Replaces W10416065, 8208290, C8931605, 67005560, and more. No tools required — installs in under 15 minutes. Common Problems This Part Fixes Refrigerator not cooling — compressor not running Freezer section too warm or not freezing Both refrigerator and freezer compartments gradually warming up Repeated clicking sound every 2–5 minutes from behind or underneath the refrigerator Compressor hums briefly then shuts off without reaching operating temperature Refrigerator runs but cannot maintain set temperature Shaking the start relay reveals a rattling sound inside — confirms internal failure Replaces Part Numbers This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers: W10613606, 67005560, 3023300, 67003186, 67003764, 67005561, 67005562, W10416065, 8171210, 8208290, 8208368, W10244032, 302TFBYY, SSP14R302TFR,  AWP41206, C8931605, PD00004905, EAP8746522, AP5787784, PS8746522. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This start relay and capacitor is compatible with select refrigerators from the following brands: Whirlpool refrigerators (side-by-side, French door, bottom-freezer) Kenmore / Sears refrigerators (select Whirlpool-built models) Maytag refrigerators KitchenAid refrigerators Amana refrigerators Jenn-Air refrigerators Admiral refrigerators Crosley refrigerators Dacor refrigerators Hardwick refrigerators Inglis refrigerators Litton refrigerators Magic Chef refrigerators Important: Always verify your refrigerator's model number and compare the old relay's shape and terminal configuration to the new part before installing. Some models may require trimming the wire connector tabs for a proper fit. Contact our support team with your model number if you need confirmation before ordering. Key Features Provides the initial electrical surge needed to start the compressor motor — without it, the compressor cannot run and the refrigerator cannot cool Kit includes both the start relay and the CBB61 run capacitor (15µF ±5%, 250VAC) — everything needed in one package Plugs directly onto the compressor terminals — no wiring or soldering required in most cases Quick rattle test — shake the old relay; if it rattles, the internal contacts have failed and it needs replacement Replaces W10416065, 8208290, C8931605, and over a dozen additional cross-reference part numbers Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Fast DIY repair — installs in under 15 minutes, no tools required in most cases Product Specifications Part Number W10613606 Part Type Refrigerator Compressor Start Relay and Capacitor Kit Condition Aftermarket Replacement Application Refrigerator Compressor (side-by-side, French door, bottom-freezer) Capacitor Type CBB61 Run Capacitor Capacitor Rating 15µF ±5%, 250VAC Kit Includes 1x Start relay, 1x CBB61 capacitor Installation Plug-in — no tools required in most cases Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, Magic Chef Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning. Move the refrigerator away from the wall to access the rear or lower back panel. Remove the rear access panel by unscrewing the retaining screws to expose the compressor. The compressor is a large black dome-shaped component — the start relay and capacitor assembly plugs onto the side terminals. Grip the old relay firmly and pull it straight off the compressor pins. Shake it — if it rattles, the internal contacts have failed and replacement is confirmed. Compare the old relay to the new W10613606 to confirm the terminal layout matches. Align the new relay with the compressor pins and press it firmly on. Reinstall the access panel, restore power, and listen for the compressor to start and run normally within a few minutes. Note: Some models may require trimming the wire connector tabs or reversing the connector orientation for a proper fit — do not force the connection. Tools needed: Phillips screwdriver (for panel access only). Frequently Asked Questions What does the compressor start relay do? The start relay plugs onto the compressor terminals and provides the brief but powerful surge of electrical current needed to start the compressor motor from a standstill. Once the compressor reaches operating speed — usually within a second or two — the relay drops out and the compressor runs on its own. Without a working start relay, the compressor cannot start at all, and the refrigerator stops cooling. The capacitor works alongside the relay to store and deliver the extra energy needed on startup. How do I know if my start relay has failed? The most reliable quick test is the rattle test: unplug the refrigerator, pull the start relay off the compressor, and shake it near your ear. A working relay is silent. A failed relay will rattle — the internal contacts have broken free and are loose inside the casing. Another sign is a repeated clicking sound every 2–5 minutes from the back of the refrigerator, where the compressor attempts to start, fails, trips the overload protector, rests, and tries again. If the fridge is warm and you hear clicking, check the relay first. What is the difference between the start relay and the capacitor? The start relay is the switching device that connects and disconnects the start winding of the compressor motor during startup. The capacitor stores a charge and releases it during startup to give the motor the additional torque it needs to get moving under load. Together they work as a startup system for the compressor. This kit includes both — replacing both at the same time ensures the complete startup circuit is fresh and reliable. My fridge is still not cooling after replacing the start relay — what else could it be? If replacing the start relay does not restore cooling, other possible causes include a failed compressor (the compressor runs but no longer builds pressure), a refrigerant leak in the sealed system, a failed start capacitor (if not replaced along with the relay), a bad overload protector, or a faulty main control board. Listen carefully after installing the new relay — if the compressor now starts and runs but the fridge still doesn't cool after several hours, a sealed system issue or refrigerant problem is likely and will require a certified technician. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and terminal configuration of the original W10613606 start relay and capacitor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WG447 Microwave Mica Sheet, Waveguide Cover – Compatible with Whirlpool, GE, Samsung, LG, Panasonic, and More Product Description Protect your microwave’s internal components with the WG447 Microwave Mica Sheet / Waveguide Cover. Microwave mica chips can effectively prevent water or oil and other substances from splashing on the magnetron or other components during the heating process of food. Protect the microwave oven from burning. Size can be cut: The waveguide cover size is 10 cm*10.8 cm (3.93 in x 4.65 in), you could cut it into any size to fit your microwave oven. Easy to cut. Widely used: As a kind of heat resisting and insulating product. Mica Plates is widely used in household appliances such as hair dryers, toasters, microwave ovens, warmers, etc.  Replaces Part Numbers universal microwave mica sheet equivalents. Size can be cut: The waveguide cover size is 10 cm*10.8 cm (3.93 in x 4.65 in), you could cut it into any size to fit your microwave oven. Easy to cut.   Compatibility This replacement waveguide cover fits a wide range of Whirlpool, GE, Samsung, LG, Panasonic, Emerson, Sharp, Kenmore, and other microwaves that use a cut-to-fit mica sheet. Common compatible models include (but are not limited to):Whirlpool WMH31017HS, GE JVM3160RFSS, Samsung ME18H704SFS, LG LMV1762ST, Panasonic NN-SN766S. Always compare dimensions before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Universal cut-to-fit design matches OEM insulation and heat resistance ⚡ Restores Safe Operation – Prevents arcing, sparking, and microwave energy leakage 🔥 Heat & Moisture Resistant – Made from high-grade mica composite ✂️ Easy to Trim – Can be cut to match original waveguide cover size 🛡️ Fixes Common Issues – Solves sparking, burning smell, and uneven heating caused by damaged covers 📐 Product Specification Part Number: WG447 Component Type: Microwave Mica Sheet / Waveguide Cover Material: Heat-resistant mica composite Dimensions: Approx. 6" × 6" (can be trimmed to size) Thickness: Standard 0.3–0.4 mm mica sheet Mounting: Press-fit or screw-secured depending on model Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Scissors or utility knife (for trimming), screwdriver (if applicable) ⚠️ Safety First: Always unplug the microwave before servicing. Do not operate the microwave without a waveguide cover. Steps: Disconnect power and remove the old burned or damaged mica cover. Use the old cover as a template to trim the new WG447 mica sheet. Align the new cover over the waveguide opening. Press into clips or secure with screws depending on your model. Restore power and test heating performance. ⏱️ Time Required: 5–10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop microwave sparking and restore safe heating — Add to Cart Now for a quick, reliable fix!

Read more less

XPARTCO W11220230 Washer Water Inlet Valve The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.. Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors. Quick Answer The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation. Common Problems This Part Fixes Washer not filling with water Slow water fill during cycles Water continuously flowing into washer Incorrect water temperature Washer stopping due to fill errors Leaking or stuck inlet valve Replaces Part Numbers This water inlet valve replaces the following part numbers: W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select washers from the following brands: Whirlpool washers Maytag washers Amana washers Kenmore / Sears washers (select models) Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Three coil hot and cold water valve. OEM-equivalent fit, performance, and durability Restores proper water fill levels and cycle operation Durable construction resists mineral buildup and wear Prevents leaks and overfilling issues Direct replacement for W11220230 valve assembly Product Specifications Part Number W11220230 Part Type three coil hot and cold water inlet valve. Application Top Load / Front Load Washers Condition Aftermarket Replacement Function Controls Water Flow Compatible Brands Whirlpool, Maytag, Amana, Kenmore Installation Notes ⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation. Frequently Asked Questions What does a washer water inlet valve do? It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill. Will this fix a washer that won’t fill? Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406107 Dryer Door Switch – Replaces WP3406107 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Ensure your dryer starts safely and operates correctly with the XPARTCO 3406107 Dryer Door Switch. This high-quality aftermarket replacement detects when the dryer door is closed, enabling the motor to run and heat to activate. A defective switch can prevent your dryer from starting or cause it to stop mid-cycle. Replacing it with this reliable XPARTCO switch restores normal operation and dependable performance. Replaces Part Numbers WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, PS11741701. Compatibility This replacement door switch fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.60902990, and Maytag MEDC200XW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Engineered to match OEM safety and electrical performance 🚪 Restores Start Function – Ensures dryer runs only when the door is fully closed 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ Quick Installation – Simple plug-in wiring and snap-in mounting 🛡️ Fixes Common Issues – Solves dryer not starting, shutting off mid-cycle, or running with door open 📐 Product Specification Part Number: 3406107 Component Type: Dryer Door Switch Assembly Material: Plastic body with metal actuator lever and 3-pin terminal Mounting: Snap-in installation behind front panel Electrical Rating: 15A / 125-250V AC Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and open the dryer door. Remove the top or front panel (depending on model). Unplug the old switch’s wire connectors. Press the locking tabs and remove the old switch. Install the new XPARTCO 3406107 switch, reconnect wires, and secure panels. Restore power and test dryer start function. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s start function — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO 6501EA1001R Washer Water Level Pressure Switch The XPARTCO 6501EA1001R is an aftermarket replacement water level pressure switch compatible with select LG and Kenmore top-load and front-load washers — including the WT1, WT4, WT5, WT7 series and WM series. The pressure switch is a sealed sensor connected to the tub by a flexible air hose. As water fills the tub, air pressure inside the hose increases proportionally, and the switch translates that pressure into an electrical signal that tells the control board the current water level. The control board uses this signal to know when to stop filling, when to add more water, and to confirm the tub has drained before advancing to the next cycle phase. When the pressure switch fails, the washer may not fill with enough water, may overfill and leak (error code UE), may stop filling altogether, or may display error codes E4, E7, PE, F04, or F05 depending on the model. This switch has a body diameter of approximately 2.3"–2.4", body height of approximately 2.05", and includes an air pressure hose approximately 29" long. It directly replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, 5210FA3427J, AP5204365, AH3529177, EA3529177, EAP3529177, and PS3529177. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6501EA1001R Washer Water Level Pressure Switch fixes LG and Kenmore washers displaying error codes E4, E7, PE, UE (overflow), F04, or F05, not filling with enough water, overfilling and leaking, or not filling at all. Body diameter ~2.3"–2.4", height ~2.05", 29" air pressure hose. Replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, AP5204365, PS3529177. Compatible with LG WT1xxx–WT7xxx, WM series, and Kenmore (LG-built) washers. Common Problems This Part Fixes Error codes E4, E7, or PE displayed — water level pressure switch fault Error code UE (overflow) — switch not signaling the control board to stop filling Error codes F04 or F05 displayed on certain models — water level sensing fault Washer not filling with enough water for the selected cycle Washer overfilling — water level rising past the normal fill point and leaking from the tub Washer not filling with water at all Washer stopping mid-cycle due to a water level fault Inconsistent or inaccurate water level across different load sizes Replaces Part Numbers This pressure switch directly replaces the following OEM and cross-reference part numbers: 6501EA1001R, EBF62754506, 2651052, 5210FA3427J, 6501EA1001C, PD00022947, EAP3529177, AH3529177, EA3529177, AP5204365, ALG1185730, OEM15613104, PS3529177. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This pressure switch is compatible with select LG and Kenmore washers from the following series: LG top-load washers — WT1 series (WT1101CW, WT1201CW, WT1201CV, WT1501CW, WT1701CW, WT1801HVA, WT1801HWA and related models) LG top-load washers — WT4 series (WT4870CW, WT4970CW and related models) LG top-load washers — WT5 series (WT5001CW, WT5070CW, WT5101HV, WT5101HW, WT5270CW, WT5680HVA, WT5680HWA and related models) LG top-load washers — WT7 series (WT7200CW, WT7200CV, WT7300CW, WT7305CV, WT7600HWA, WT7600HKA and related models) LG front-load washers — WM series (WM2032HS and related models) LG washers — T1309ADFH, T1309ADFH6, T1309ADFN, WF-T8501 series Kenmore / Sears washers — 79629272000, 79629278000, 79631512210, 79631512211, 79631463410, 79629002010, 79629478000, 79631412310 and related models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Senses water level in the tub via air pressure changes in a connected hose — signals the control board to start, stop, or adjust water fill Resolves error codes E4, E7, PE, UE, F04, and F05 caused by pressure switch failure on compatible models Body diameter approximately 2.3"–2.4", body height approximately 2.05" Includes air pressure hose approximately 29" long Prevents overfilling and underfilling — restores accurate, energy-efficient water level control Replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, AP5204365, and PS3529177 Compatible with LG WT1xxx, WT4xxx, WT5xxx, WT7xxx, WM series, and Kenmore LG-built washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6501EA1001R Also Replaces 6501EA1001C, 6501EA1001D (prior versions) Part Type Washer Water Level Pressure Switch Condition Aftermarket Replacement Application LG and Kenmore Top-Load and Front-Load Washers Body Diameter Approximately 2.3 – 2.4 inches Body Height Approximately 2.05 inches Hose Length Approximately 29 inches Error Codes Resolved E4, E7, PE, UE, F04, F05 Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. On most LG top-load models, the pressure switch is located behind the control panel or console at the top of the washer. Slide and lift the top panel or remove the control panel screws to access the switch — refer to your model's service instructions if uncertain. Locate the switch and its connected air pressure hose, which routes down to a fitting on the tub. Photograph the wire harness connections before disconnecting. Disconnect the wire harness connector from the switch. Carefully disconnect the air pressure hose from the old switch (avoid kinking or puncturing the hose). Unclip or unscrew the old switch from its mounting bracket. Install the new 6501EA1001R switch into the mounting slot, ensuring it locks securely with the retaining tabs. Reconnect the air pressure hose and the wire harness. Reinstall the panel, restore power, and run a fill cycle to confirm normal water level control and check that no error codes appear. Tools needed: Phillips screwdriver, putty knife (for some models). Frequently Asked Questions What do error codes E4, E7, and PE mean on LG washers? E4 and E7 on LG front-load and top-load washers, and PE on certain LG top-load models, all indicate a water level sensing fault detected by the pressure switch. These codes appear when the control board receives an inconsistent, absent, or out-of-range pressure signal from the switch — preventing the washer from accurately determining how much water is in the tub. Replacing the pressure switch resolves these codes when the switch itself has failed; if the air hose is pinched, disconnected, or has a small leak, that should also be checked and corrected before assuming the switch needs replacement. What does error code UE mean and how does the pressure switch relate to it? UE typically indicates an unbalanced load error on LG washers, but in some cases it can also appear in connection with overfilling caused by a pressure switch that is not correctly signaling the control board to stop adding water. If you are experiencing overflow along with a UE code, and you've confirmed the load is balanced and not the unbalance cause, a failed pressure switch allowing continuous fill is a possible explanation and replacing the switch can resolve the overfill behavior. What is the difference between 6501EA1001R and 6501EA1001C? These are the same pressure switch across different production revisions. 6501EA1001C was an earlier version, and 6501EA1001R is the current updated part number. The 6501EA1001D and 6501EN1001R are also cross-references for this same switch. All are fully interchangeable — if your washer's parts diagram shows any of these numbers, this replacement covers all of them. My washer isn't filling with enough water — could it be the pressure switch instead of the inlet valve? Yes — insufficient water fill is commonly assumed to be a water inlet valve problem, but the pressure switch is just as likely a cause. If the inlet valve is delivering water normally but the pressure switch is misreporting the water level as already full, the control board will stop the fill cycle prematurely. Before replacing the inlet valve, check the pressure switch's air hose for kinks, pinches, or disconnection, and consider testing or replacing the switch if the hose is intact and undamaged. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the dimensions and air-pressure sensing performance of the original 6501EA1001R water level pressure switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8066184 Dryer Motor Pulley Replaces WP8066184 The XPARTCO 8066184 is an aftermarket replacement dryer motor pulley compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef. The motor pulley is a small but critical metal component that threads onto the dryer motor shaft and serves as the anchor point for the drive belt. As the motor spins, the belt wraps around the motor pulley to transfer rotation to the drum via the idler pulley. When the motor pulley cracks, strips, or breaks, the belt loses its anchor point on the motor side — the drum stops spinning even though the motor continues to run. Made from durable metal, this motor pulley measures 1-1/8" L x 1-3/8" W x 1-1/8" H and is designated Pulley 29 (60Hz). It threads onto the motor shaft with a left-hand (reverse) thread — it tightens clockwise and loosens counter-clockwise. It directly replaces WP8066184, 8578565, 3389627, 3394341, 3401143, 694871, W10299847, W10290525, W10290531, W10402909, and WP8066184VP. Installs in 30–45 minutes with basic hand tools including a wrench. Quick Answer The XPARTCO 8066184 Dryer Motor Pulley fixes Whirlpool-family dryers where the drum is not spinning, the motor runs but the belt slips off the motor shaft, or the pulley is visibly cracked or broken. Metal, 1-1/8" L x 1-3/8" W x 1-1/8" H. Left-hand thread — loosen counter-clockwise. Replaces WP8066184, 8578565, 3394341, 694871, W10299847, and more. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef dryers. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum is still Drive belt repeatedly slipping off the motor shaft — pulley is damaged or missing Squealing or grinding noise from the motor area during the drying cycle Motor pulley visibly cracked, stripped, or broken into pieces Belt falls off immediately after being reinstalled — pulley not gripping correctly Drum spinning intermittently due to a pulley that is partially damaged Replaces Part Numbers This motor pulley directly replaces the following OEM and cross-reference part numbers: WP8066184, 8066184, 8578565, W10299847, 1200324, 3389627, 3394341, 3401143, 694871, W10290525, W10290531, W10402909, AWP48528, AP6011686, EAP11744884, PD00028572, PS11744884. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor pulley is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric — WED, WGD, and related series) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric — MEDC, MED, MGD, and related series) KitchenAid dryers Amana dryers (NED, NGD, and related series) Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Threads onto the motor shaft to serve as the drive belt anchor point — transfers motor rotation to the drum via the drive belt Durable metal construction — resists cracking, stripping, and wear under continuous high-speed motor operation Dimensions: 1-1/8" L x 1-3/8" W x 1-1/8" H — Pulley 29 designation (60Hz motors) Left-hand (reverse) thread — tightens clockwise, loosens counter-clockwise — do not force removal with standard right-hand tools Replaces WP8066184, 8578565, 3394341, 694871, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform Often replaced together with the drive belt (341241) and idler pulley (279640 or W10837240) for a complete drum drive repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools including a wrench Product Specifications Part Number 8066184 OEM Part Number WP8066184 Part Type Dryer Motor Pulley Condition Aftermarket Replacement Application Gas and Electric Dryers Material Metal Dimensions 1-1/8" L x 1-3/8" W x 1-1/8" H Pulley Designation Pulley 29 (60Hz) Thread Direction Left-hand (reverse) thread — loosen counter-clockwise Often Replaced With 341241 Drive Belt, 279640 or W10837240 Idler Pulley Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Left-Hand Thread: Loosen Counter-Clockwise Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel and front panel to access the motor and drum area. Release the drive belt tension from the idler pulley and slide the belt off the motor pulley. The motor pulley threads onto the motor shaft with a left-hand (reverse) thread — to remove it, turn it counter-clockwise (which is the tightening direction for standard threads). Use two adjustable wrenches or a wrench and pipe for additional leverage if the pulley is stuck — a penetrating oil applied and allowed to soak for 10–15 minutes can help free a seized pulley. Once removed, thread the new 8066184 pulley clockwise onto the motor shaft (which tightens it due to the left-hand thread) and snug it firmly. Re-route the drive belt around the new motor pulley and idler pulley, reinstall the front and top panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, two adjustable wrenches or pipe wrench. Frequently Asked Questions What does the dryer motor pulley do? The motor pulley is a small threaded metal wheel that screws onto the dryer motor shaft. The drive belt wraps around the motor pulley on one side and the drum on the other, with the idler pulley maintaining tension. As the motor spins, the motor pulley rotates with it, pulling the belt and turning the drum. Without the motor pulley — or with a cracked or stripped one — the belt has no grip point on the motor side and the drum will not rotate even though the motor is running normally. Why does this pulley have a left-hand (reverse) thread? The motor pulley uses a left-hand thread so that the motor's rotation naturally tightens the pulley during normal operation rather than loosening it. Since the motor spins in a direction that would loosen a standard right-hand thread, Whirlpool designed the motor pulley with a reverse thread to prevent it from backing off and falling loose during use. This means: to remove the old pulley, turn it counter-clockwise (opposite of standard). To install the new pulley, turn it clockwise to tighten. What is the difference between 8066184 and WP8066184? These are the same motor pulley. WP8066184 is the updated Whirlpool OEM part number that superseded the original 8066184. The 8578565 and 3394341 are also cross-references for this same pulley from earlier production runs. This aftermarket replacement is compatible with all of these numbers. Should I also replace the drive belt and idler pulley at the same time? Yes — since the dryer is already disassembled, inspect and replace the drive belt (341241) and idler pulley (279640 or W10837240 depending on your model) at the same time. A broken motor pulley often damages or frays the belt, and the idler pulley bearing wears at a similar rate. Replacing all three together in a single repair eliminates the most common drum drive failure points and prevents a repeat teardown in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable metal to match the dimensions and thread specification of the original WP8066184 motor pulley. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10198086 Replacement Dryer Drum Belt - Compatible with Whirlpool, Maytag replaces WPW10198086 Product Description Ensure your dryer’s drum rotates smoothly with the W10198086 Replacement Dryer Drum Belt. This high-quality replacement part is designed for select Whirlpool, Maytag, Kenmore, and other dryers, connecting the motor to the drum to enable proper tumbling during drying cycles. It addresses issues like the drum not spinning, unusual noises, or failure to start, offering a cost-effective alternative to OEM parts with equivalent performance. Note: Includes one dryer drum belt. Disconnect power before installation. Inspect the idler pulley and motor pulley for wear to prevent repeat failures. This is a replacement part designed to match OEM specifications. Replaces part numbers: WPW10198086, W10198086, 1481904, W11575709, W11667279, LB8086, PD00007598, EAP11750135, AP6016842, PS11750135. Compatibility: Compatible with models including but not limited to: Whirlpool: WED9151YW0, WED9050XW0, WED9150WW0, WED9200SQ0, WED9400SW0, WED9500TW0, WGD9151YW0, WGD9200SQ0, WGD9400SW0 Maytag: MED6000XW0, MED7000XW0, MGD6000XW0, MGD7000XW0 Kenmore: 110.67032600, 110.67086600, 110.68812790, 110.78832790, 110.97831790 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, and other dryers. 🔧 Specifications: 92-1/4" long, 5-rib, 1/4" wide belt drives the dryer drum for efficient tumbling. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, wrench, work gloves; typically installed in 20–40 minutes with YouTube video guidance. 🛡️ Effective Fixes: Resolves drum not spinning, noisy operation, or failure to start. Product Specification Part Number: W10198086 Component Type: Dryer drum belt Material: Durable rubber Dimensions: Approximately 92-1/4" length, 1/4" width, 5 ribs Mounting: Loops around drum, motor pulley, and idler pulley Operating Conditions: Suitable for high-tension dryer drum systems Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tip: Access the drum by removing the dryer’s top or front panel; thread the belt through the idler pulley and around the motor pulley, ensuring proper tension. Watch YouTube videos for step-by-step guidance. Check idler pulley and motor pulley for wear to avoid premature belt failure. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO WE04X10052 Dryer Door Switch - Compatible with GE, Hotpoint Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO WE04X10052 Dryer Door Switch. This door switch is designed for select GE and Hotpoint dryers, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WE04X10052, 877374, WE4X10052, EXPWE4X10052, PD00030680, AH265289, EAP265289, EA265289, AP2042951, PS265289. Compatibility: Compatible with models including but not limited to: GE: WSM2420D0CC , WSM2420D0WW , WSM2420D1CC , WSM2420D1WW , WSM2420D2CC , WSM2420D2WW , WSM2420D3WW , WSM2420D4WW , WSM2420D5WW , WSM2420TAAAA , WSM2420TAACC , WSM2420TAAWW , WSM2420TBAAA , WSM2420TBAWW , WSM2480D0WW , WSM2480D1WW , WSM2480D2WW , WSM2480D3WW , WSM2480TAAAA , WSM2480TAAWW , WSM2480TBAAA , WSM2480TBAWW , WSM2480TCAAA , WSM2480TCAWW Hotpoint: HTDP120EDWW, NVLR333EE0WW, HTDX100GDWW Other brands: Select models requiring WE04X10052 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Hotpoint, and other dryers requiring WE04X10052. 🔥 Specifications: replacement dryer door switch, 2- or 3-terminal configuration, push-to-start functionality. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop. Product Specification Part Number: XPWE04X10052 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: 2- or 3-terminal (model-specific, verify before purchase) Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO DC47-00016A Dryer Thermostat - Compatible with select Samsung, Whirlpool, Maytag, Kenmore Dryers Product Description Protect your dryer from overheating with the replacement DC47-00016A Dryer Thermostat. This thermal cut-off thermostat is designed for select Samsung, Whirlpool and Kenmore dryers, shutting off the motor when the dryer overheats to prevent damage or hazards. It addresses issues like no heat, insufficient heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermal cut-off thermostat with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: DC47-00016A, L0016A, AP4201894, PS4205213, AP6008681, EAP4205213, EAP11741821, PD00005341, PD00003747, PS11741821, 35001087, WP35001087. Compatibility: Compatible with models including but not limited to: Samsung: DV203AGS, DV203AGW/XAA-0000, DV206AES, DV209AEW/XAA-0000, DV210AEW, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, and LG dryers. 🔥 Specifications: replacement thermal cut-off thermostat, opens at 260°F, two 1/4" male spade terminals. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, insufficient heat, failure to start, or premature shutoff. Product Specification Part Number: XPARTCO DC47-00016A Component Type: Thermal cut-off thermostat Material: Metal and plastic Electrical Specs: 125/250V, 25A, 85°C - 35°C, 185°F. Mounting: Two 1/4" male spade terminals, mounts on blower housing Operating Conditions: Suitable for high-temperature dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and efficient today! Add to cart now for a budget-friendly fix!

Read more less