Appliance Parts

2 Pack - 12638000004021 Genuine OEM Midea Dryer Drum Support Roller The 12638000004021 is a Genuine OEM Midea replacement dryer drum support roller compatible with a wide range of Midea, Criterion, Insignia, and Frigidaire-branded Midea-built electric and gas dryers. The drum support roller is a cylindrical wheel mounted on a fixed shaft inside the dryer cabinet that cradles and supports the outer rim of the drum as it rotates. As the roller wheel wears down or the axle bushing degrades, the drum no longer rides smoothly, causing thumping, rumbling, or squealing noises, or in advanced cases, preventing the drum from turning freely. This is a single roller, sold individually — most compatible dryers use multiple support rollers, so check your model's parts diagram to confirm the quantity needed for a complete repair. As a Genuine OEM part manufactured by Midea to factory specifications, the 12638000004021 directly replaces 12638000000786 and is also cross-referenced under the Frigidaire-branded catalog number 5304511415, since Frigidaire-branded units in this size class are built by Midea and share the same roller component. Installs in 30–45 minutes with basic hand tools. Quick Answer The 12638000004021 Genuine OEM Midea Dryer Drum Support Roller fixes Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers that are thumping, rumbling, squealing, or where the drum isn't turning smoothly. Sold individually — check your model's parts diagram for the total quantity needed. Genuine OEM. Replaces 12638000000786, Frigidaire 5304511415. Compatible with Midea MLG45N1BWW and related Midea, Criterion, Insignia, and Frigidaire-branded dryer models. Common Problems This Part Fixes Loud thumping or rumbling noise during the drying cycle — worn drum roller wheel Squealing or squeaking noise — roller bushing or axle wearing out Drum turning unevenly or wobbling — roller no longer supporting the drum smoothly Drum not spinning at all — roller(s) worn to the point the drum has dropped off the support path Scraping or grinding noise — roller wheel surface worn flat and dragging against the drum rim Excessive vibration during the drying cycle Visible flat spots, cracks, or uneven wear on the roller wheel Replaces Part Numbers This drum support roller directly replaces the following OEM and cross-reference part numbers: 12638000004021,  AP7990985, PS18170578, 5304511415, 4056012471. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drum support roller is compatible with select Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers, including: Midea MLG45N1BWW gas dryer Midea MLE, MLG, MLTE, and MLTG series electric and gas dryers (select models) Criterion electric and gas dryers (select models) Insignia electric and gas dryers (select models) Frigidaire-branded dryers built by Midea (select models — see Frigidaire cross-reference 5304511415) Important: This roller is sold individually. Most dryers on this platform use multiple drum support rollers — check your specific model's parts diagram to confirm the total quantity needed, and consider replacing all rollers at the same time for even drum support. Always verify your model number before ordering. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Supports and cradles the drum rim as it rotates for smooth, quiet operation Reduces drum noise and wear caused by an aging or damaged roller Sold individually — verify total quantity needed per your model's parts diagram Replaces 12638000000786 and Frigidaire cross-reference 5304511415 Compatible with Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 12638000004021 Part Type Dryer Drum Support Roller Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Quantity Pack of 2 Compatible Brands Midea, Criterion, Insignia, Frigidaire (Midea-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power (and shut off gas first for gas dryer models) before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Access the drum rollers by removing the back panel of the dryer. Take a photo of the belt routing and roller positions before removing anything. Release the drive belt from the idler pulley, lift the drum, and set it aside. Each drum roller is mounted on a fixed shaft inside the dryer cabinet, typically secured by a retaining clip. Use needle-nose pliers to remove the old clip, slide the old roller off the shaft, and slide the new roller on. Reinstall the retaining clip to secure the new roller. If your model uses multiple rollers, repeat for each one — replacing all rollers at the same time is recommended for even drum support. Reinstall the drum, re-route the belt, and reassemble the rear panel. Restore power and run a test cycle to confirm quiet, smooth drum operation. Tools needed: Phillips screwdriver, Torx screwdriver (model dependent), needle-nose pliers, work gloves. Frequently Asked Questions How many drum rollers does my Midea dryer have? The number of drum support rollers varies by model on the Midea dryer platform. This listing is for a single roller. Before ordering, look up your dryer's model number in the official parts diagram to confirm how many rollers your specific dryer uses, and order enough to replace all of them if you want even drum support. Replacing all rollers at once — rather than just the noisiest one — is generally the most cost-effective approach since they tend to wear out around the same time. Does this roller fit my Frigidaire dryer? Yes, on select models. Some Frigidaire-branded dryers in certain size classes are manufactured by Midea and use the same internal components, including this drum support roller — cross-referenced under Frigidaire part number 5304511415. Always verify your specific Frigidaire model number before ordering to confirm it is a Midea-built unit using this roller. What is the difference between 12638000004021 and 12638000000786? These are the same drum support roller. 12638000000786 is an earlier or alternate catalog reference for the identical Midea-manufactured roller, and 12638000004021 is the current manufacturer part number. If your dryer's parts diagram or supplier listing shows 12638000000786, the 12638000004021 is the correct current part and this listing covers both references. Should I replace the drum belt and idler pulley at the same time? Since the dryer cabinet must already be opened to access the drum rollers, this is a good opportunity to also inspect the drum belt and idler pulley for wear. These components work together as the drum drive system, and a worn belt or idler pulley can accelerate roller wear (and vice versa). If you notice cracking, fraying, or looseness in the belt, or if the idler pulley wheel doesn't spin freely, replacing them in the same repair can help prevent a near-term repeat teardown. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum support roller installed in compatible Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

12638000004021 Genuine OEM Midea Dryer Drum Support Roller The 12638000004021 is a Genuine OEM Midea replacement dryer drum support roller compatible with a wide range of Midea, Criterion, Insignia, and Frigidaire-branded Midea-built electric and gas dryers. The drum support roller is a cylindrical wheel mounted on a fixed shaft inside the dryer cabinet that cradles and supports the outer rim of the drum as it rotates. As the roller wheel wears down or the axle bushing degrades, the drum no longer rides smoothly, causing thumping, rumbling, or squealing noises, or in advanced cases, preventing the drum from turning freely. This is a single roller, sold individually — most compatible dryers use multiple support rollers, so check your model's parts diagram to confirm the quantity needed for a complete repair. As a Genuine OEM part manufactured by Midea to factory specifications, the 12638000004021 directly replaces 12638000000786 and is also cross-referenced under the Frigidaire-branded catalog number 5304511415, since Frigidaire-branded units in this size class are built by Midea and share the same roller component. Installs in 30–45 minutes with basic hand tools. Quick Answer The 12638000004021 Genuine OEM Midea Dryer Drum Support Roller fixes Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers that are thumping, rumbling, squealing, or where the drum isn't turning smoothly. Sold individually — check your model's parts diagram for the total quantity needed. Genuine OEM. Replaces 12638000000786, Frigidaire 5304511415. Compatible with Midea MLG45N1BWW and related Midea, Criterion, Insignia, and Frigidaire-branded dryer models. Common Problems This Part Fixes Loud thumping or rumbling noise during the drying cycle — worn drum roller wheel Squealing or squeaking noise — roller bushing or axle wearing out Drum turning unevenly or wobbling — roller no longer supporting the drum smoothly Drum not spinning at all — roller(s) worn to the point the drum has dropped off the support path Scraping or grinding noise — roller wheel surface worn flat and dragging against the drum rim Excessive vibration during the drying cycle Visible flat spots, cracks, or uneven wear on the roller wheel Replaces Part Numbers This drum support roller directly replaces the following OEM and cross-reference part numbers: 12638000004021,  AP7990985, PS18170578, 5304511415, 4056012471. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drum support roller is compatible with select Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers, including: Midea MLG45N1BWW gas dryer Midea MLE, MLG, MLTE, and MLTG series electric and gas dryers (select models) Criterion electric and gas dryers (select models) Insignia electric and gas dryers (select models) Frigidaire-branded dryers built by Midea (select models — see Frigidaire cross-reference 5304511415) Important: This roller is sold individually. Most dryers on this platform use multiple drum support rollers — check your specific model's parts diagram to confirm the total quantity needed, and consider replacing all rollers at the same time for even drum support. Always verify your model number before ordering. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Supports and cradles the drum rim as it rotates for smooth, quiet operation Reduces drum noise and wear caused by an aging or damaged roller Sold individually — verify total quantity needed per your model's parts diagram Replaces 12638000000786 and Frigidaire cross-reference 5304511415 Compatible with Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 12638000004021 Part Type Dryer Drum Support Roller Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Quantity Sold individually — verify total needed per model Compatible Brands Midea, Criterion, Insignia, Frigidaire (Midea-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power (and shut off gas first for gas dryer models) before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Access the drum rollers by removing the back panel of the dryer. Take a photo of the belt routing and roller positions before removing anything. Release the drive belt from the idler pulley, lift the drum, and set it aside. Each drum roller is mounted on a fixed shaft inside the dryer cabinet, typically secured by a retaining clip. Use needle-nose pliers to remove the old clip, slide the old roller off the shaft, and slide the new roller on. Reinstall the retaining clip to secure the new roller. If your model uses multiple rollers, repeat for each one — replacing all rollers at the same time is recommended for even drum support. Reinstall the drum, re-route the belt, and reassemble the rear panel. Restore power and run a test cycle to confirm quiet, smooth drum operation. Tools needed: Phillips screwdriver, Torx screwdriver (model dependent), needle-nose pliers, work gloves. Frequently Asked Questions How many drum rollers does my Midea dryer have? The number of drum support rollers varies by model on the Midea dryer platform. This listing is for a single roller. Before ordering, look up your dryer's model number in the official parts diagram to confirm how many rollers your specific dryer uses, and order enough to replace all of them if you want even drum support. Replacing all rollers at once — rather than just the noisiest one — is generally the most cost-effective approach since they tend to wear out around the same time. Does this roller fit my Frigidaire dryer? Yes, on select models. Some Frigidaire-branded dryers in certain size classes are manufactured by Midea and use the same internal components, including this drum support roller — cross-referenced under Frigidaire part number 5304511415. Always verify your specific Frigidaire model number before ordering to confirm it is a Midea-built unit using this roller. What is the difference between 12638000004021 and 12638000000786? These are the same drum support roller. 12638000000786 is an earlier or alternate catalog reference for the identical Midea-manufactured roller, and 12638000004021 is the current manufacturer part number. If your dryer's parts diagram or supplier listing shows 12638000000786, the 12638000004021 is the correct current part and this listing covers both references. Should I replace the drum belt and idler pulley at the same time? Since the dryer cabinet must already be opened to access the drum rollers, this is a good opportunity to also inspect the drum belt and idler pulley for wear. These components work together as the drum drive system, and a worn belt or idler pulley can accelerate roller wear (and vice versa). If you notice cracking, fraying, or looseness in the belt, or if the idler pulley wheel doesn't spin freely, replacing them in the same repair can help prevent a near-term repeat teardown. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum support roller installed in compatible Midea, Criterion, Insignia, and Frigidaire-branded Midea-built dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools. Quick Answer The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models. Common Problems This Part Fixes Dryer overheating — thermistor not accurately reporting rising temperature to the control board Dryer not heating at all — thermistor circuit open or shorted Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle Dryer taking much longer than normal to complete a cycle Not-heating fault code displayed on models with digital control panels Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading Dryer cycling heat on and off erratically Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 17438200000404, WF-123X2060,  AP7157538, PS18188581 Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including: Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13 Criterion — CDE41N1AW (electric), CDG41N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models Replaces WF-123X2060 Installs in 20–30 minutes with basic hand tools Product Specifications Part Number 17438200000404 Part Type Dryer Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at Room Temp Approximately 10,000 – 12,000 ohms (~70°F) Location Blower housing/exhaust duct or drum cavity, depending on model Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing). Frequently Asked Questions How do I test if the temperature sensor (thermistor) has failed? Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine. My Midea dryer has more than one temperature sensor — how do I know which one to replace? Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor. What is the difference between 17438200000404 and WF-123X2060? These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part. Does this sensor fit my Insignia or Criterion dryer? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

17438200000109 Genuine OEM Midea Dryer Heating Element Assembly The 17438200000109 is a Genuine OEM Midea replacement dryer heating element assembly compatible with a wide range of Midea and Insignia electric dryers, including the MLE41N1AWW, MLE43A3AWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLTE37N1BWW, CDE41N1AW, CLADE67W, LE43A3AWW, MDD160A2301E1305, and Insignia NS-FDRE67WH8A-C series. The heating element uses electrical resistance to generate the heat that warms air as it circulates through the dryer drum, evaporating moisture from wet clothes. Without a functioning heating element, the dryer will tumble and run normally but produce no heat, leaving clothes damp at the end of a cycle. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000109 is the complete heater assembly housing. It directly replaces 302461060002 and MDA17438200000109 (alternate catalog references for the same assembly). Note: when an electric dryer heating element fails due to overheating, the paired high-limit thermostat (Midea 17400513000460) is often stressed as well — inspecting or replacing it at the same time is recommended. Installs in 30–45 minutes with basic hand tools. Quick Answer The 17438200000109 Genuine OEM Midea Dryer Heating Element Assembly fixes Midea and Insignia electric dryers that tumble normally but produce no heat, dry unevenly, or take much longer than usual to dry a load. Complete heater assembly housing. Genuine OEM. Replaces 302461060002, MDA17438200000109. Compatible with Midea MLE41N1AWW, MLE43A3AWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLTE37N1BWW, CDE41N1AW, CLADE67W, LE43A3AWW, MDD160A2301E1305, and Insignia NS-FDRE67WH8A-C electric dryers. Often paired with thermostat replacement (Midea 17400513000460). Common Problems This Part Fixes Dryer tumbles normally but produces no heat Dryer takes significantly longer than usual to dry a full load Clothes coming out damp or only partially dried at the end of a cycle Uneven heat distribution — some loads dry while others don't Heating element visibly burned through, broken, or showing signs of arcing Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Replaces Part Numbers This heating element assembly directly replaces the following OEM and cross-reference part numbers: 17438200000109, AP7157535, PS18188573, MDA17438200000109 Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element assembly is compatible with select Midea and Insignia electric dryers, including: Midea MLE41N1AWW, MLE41N1AWWC electric dryers Midea MLE43A3AWW, LE43A3AWW, LE43A3AWWFR electric dryers Midea MLE47A3AGG electric dryer Midea MLE47C3AWW, MLE47C4AWW electric dryers Midea MLE47R5BWW electric dryer Midea MLTE37N1BWW electric dryer Midea CDE41N1AW electric dryer Midea CLADE67W electric dryer Midea MDD160A2301E1305 electric dryer Insignia NS-FDRE67WH8A-C electric dryer (6.7 cu. ft., Midea-built) Insignia NS-TDRE67W1 electric dryer (Midea-built) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Complete heater assembly housing — generates the heat needed for the drying cycle Delivers consistent, even heat distribution to reduce drying time and energy consumption Durable construction designed to withstand frequent daily drying cycles Replaces 302461060002 and MDA17438200000109 Compatible with Midea MLE, LE, CDE, CLADE, MLTE, and MDD series electric dryers, plus Insignia Midea-built models Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 17438200000109 Part Type Dryer Heating Element Assembly Condition Genuine OEM Application Electric Dryers (Midea platform) Often Replaced With High-Limit Thermostat (Midea 17400513000460) Compatible Brands Midea, Insignia (Midea-built) Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Pull the dryer away from the wall and remove the rear service panel to expose the heating element housing. Take a photo of the wiring before disconnecting anything — this is important since the high-limit thermostat and thermal cut-off wiring are both in the same area as the element leads and it's easy to mix up terminals. Disconnect the high-limit thermostat/thermal cut-off wiring and the element leads from the old heating element assembly. Remove the mounting screws securing the element housing and slide the old assembly out. Install the new 17438200000109 assembly in the same orientation, reconnect all wires snugly to the correct terminals as documented in your photo, and reinstall the mounting screws. Reassemble the rear service panel, restore power, and run a test heat cycle to confirm the dryer is heating properly. Tip: while the rear panel is open, inspect the high-limit thermostat (Midea 17400513000460) — if the original element failed due to overheating, the thermostat may also need replacement. Tools needed: Phillips screwdriver, nut driver. Frequently Asked Questions How do I know if my dryer's heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp or only partially dried. You may also notice the dryer taking significantly longer than usual to dry a load as it tries to compensate with extended tumbling time. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit. Should I replace the thermostat at the same time as the heating element? It's a good idea to inspect it. When a heating element fails due to overheating — rather than simple end-of-life wear — the paired high-limit thermostat (Midea 17400513000460) located in the same area can also be stressed by the same heat event. Since the rear panel must already be open to replace the element, checking the thermostat's continuity at the same time is a quick step that can prevent a repeat repair if the thermostat is also on the verge of failing. What is the difference between 17438200000109 and 302461060002? These are the same heating element assembly. 302461060002 and MDA17438200000109 are alternate catalog reference numbers used by some parts suppliers for the identical Midea heater assembly. If your dryer's parts diagram or supplier listing shows either of these numbers, the 17438200000109 is the correct part and this listing covers all three references. Does this element fit my Insignia dryer? Yes — Insignia is a Best Buy house brand, and several Insignia electric dryer models (including the NS-FDRE67WH8A-C and NS-TDRE67W1) are manufactured by Midea and use the same internal components, including this heating element assembly. Always verify your specific Insignia model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same heating element assembly installed in compatible Midea and Insignia electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH12X10614C Washer Genuine Electronic Control Board Replaces Part Number: WH12X10614C, WH12X10614, WH12X10538, AP8056060.

Read more less

5304509493 Electric Range Oven Genuine OEM Control Board Genuine Frigidaire part Replaces Part Numbers: 5304509493, 316557115, 4547461, AFR17844, A03619506, EAP12114577, SF5401-S9506, PD00038168, AP6248375, PS12114577  

Read more less

WD19X24829 Genuine OEM GE Dishwasher Drain Pump Kit The WD19X24829 is a Genuine OEM GE replacement dishwasher drain pump kit compatible with select GE, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers. The drain pump removes wastewater from the dishwasher tub during the drain portion of each wash and rinse cycle. Without a properly functioning drain pump, water cannot be expelled from the tub — leaving standing water after a cycle, preventing the dishwasher from advancing to the next phase, or causing slow drainage that affects wash and dry performance. As a Genuine OEM part manufactured by GE to factory specifications, the WD19X24829 is the current production drain pump kit that supersedes the earlier WD19X24394. Note: replacing this pump requires pulling the dishwasher out from under the counter to access the pump on the underside of the appliance — the pump is not accessible from inside the tub. It directly replaces WD19X24394, AP6802078, 4863016, PS12582714, and EAP12582714. Installs in 30–45 minutes with basic hand tools. Quick Answer The WD19X24829 Genuine OEM GE Dishwasher Drain Pump Kit fixes GE dishwashers that won't drain, leave standing water in the tub, make unusual noise during draining, or stop mid-cycle due to a drain fault. Genuine OEM — supersedes WD19X24394. Note: dishwasher must be pulled out from the cabinet to access the pump from the underside. Replaces WD19X24394, AP6802078, 4863016, PS12582714, EAP12582714. Compatible with GE, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers. Common Problems This Part Fixes Dishwasher not draining — standing water remaining in the tub after a cycle Dishwasher draining very slowly — pump motor weakening below rated performance Dishwasher stopping mid-cycle — pump fault detected by control board Loud humming or buzzing during the drain phase — motor running but pump not expelling water Grinding or rattling during drain — damaged pump impeller or worn motor bearings Dishes not drying properly — standing water remaining in the tub affecting drying performance Water leaking from the bottom of the dishwasher near the pump area Replaces Part Numbers This drain pump kit directly replaces the following OEM and cross-reference part numbers: WD19X24394, 4863016, AGE24616, AP6802078, EAP12582714, PD00050849, PS12582714. WD19X24829 is the current production part number superseding WD19X24394. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drain pump kit is compatible with select dishwashers from the following GE product lines: GE dishwashers — GDF510, GDF520, GDF530, GDF535, GDF570, GDF620, GDF630, GDF640, GDF645, GDF650 series GE dishwashers — GDT530, GDT535, GDT545, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT655, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE dishwashers — DDT575, DDT595 series GE Profile dishwashers — PDT715, PDT720, PDT760, PDT775, PDT785, PDT820, PDT825 series GE Café dishwashers — CDT836, CDT875 series GE Monogram dishwashers — ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) Kenmore / Sears dishwashers (select GE-built models) Important: Replacing this drain pump requires pulling the dishwasher out from under the counter and tilting it on its side to access the pump from the underside. The pump is not accessible from inside the tub. Always verify your model number before ordering. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Removes wastewater from the tub during each drain phase so the dishwasher can advance through the wash cycle properly Engineered for quiet operation — minimizes noise during the drain cycle Current production part — directly supersedes WD19X24394 Compatible with GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers Note: dishwasher must be pulled out and tilted for pump access — not accessible from inside the tub Installs in 30–45 minutes with basic hand tools Product Specifications Part Number WD19X24829 Supersedes WD19X24394 Part Type Dishwasher Drain Pump Kit Condition Genuine OEM Access Method Dishwasher must be pulled out and tilted — pump on underside Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. This repair requires pulling the dishwasher out from under the counter. Disconnect the water supply line, drain hose, and electrical connection before pulling the unit out. Place a blanket or cardboard on the floor and carefully lay the dishwasher on its side to access the drain pump on the underside. Loosen the hose clamps at both ends of the pump and disconnect the drain hoses. Disconnect the pump wiring connector. Rotate or unscrew the old pump assembly to release it from the pump housing. Install the new WD19X24829 pump in the same position, reconnect the hoses and wiring connector, and secure the clamps and mounting hardware. Return the dishwasher to upright, reconnect the supply line, drain hose, and electrical connection, and slide it back under the counter. Restore power and water and run a test cycle to confirm normal drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, adjustable wrench, blanket or cardboard. Frequently Asked Questions What is the difference between WD19X24829 and WD19X24394? These are the same dishwasher drain pump kit. WD19X24829 is the current production part number that GE issued to supersede the earlier WD19X24394. If your dishwasher's parts diagram shows WD19X24394, the WD19X24829 is the correct current replacement to order. Why does this pump require pulling the dishwasher out? Unlike some dishwasher drain pumps that are accessible from inside the tub through the filter and pump cover, the drain pump on compatible GE models is mounted to the exterior underside of the dishwasher tub. It cannot be reached from inside without removing the entire tub assembly — which is a much larger repair. Pulling the dishwasher out from the cabinet, disconnecting it, and tilting it onto its side is the standard and only practical method for replacing this pump on compatible models. What is the difference between the drain pump (WD19X24829) and the circulation pump (WD26X23258)? These are two completely different pumps that serve different functions. The drain pump (WD19X24829) removes wastewater from the tub at the end of each wash and rinse cycle — it is the pump responsible for draining. The circulation pump (WD26X23258) pressurizes clean water and sends it to the spray arms during the wash cycle — it is responsible for cleaning. When the drain pump fails, the dishwasher won't drain and leaves standing water. When the circulation pump fails, the dishwasher drains normally but dishes don't get clean because no water is being sprayed. My dishwasher has standing water — is it always the drain pump? Not always. Standing water in a dishwasher after a cycle can be caused by a failed drain pump, a clogged drain filter, a blocked or kinked drain hose, a clogged garbage disposal connection, or a failed drain solenoid. Before replacing the pump, check the dishwasher drain filter (accessible from inside the tub at the bottom), confirm the drain hose is not kinked, and check whether the garbage disposal knockout plug has been removed if the drain hose connects to a new disposal. If all of these are clear and the dishwasher still won't drain, the pump is the most likely cause. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump kit installed in compatible GE, GE Profile, GE Café, and Monogram dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-20621C Washer Drain Pump Assembly The XPARTCO DC97-20621C is an aftermarket replacement drain pump assembly compatible with a wide range of Samsung front-load washers in the specific series, as well as select Kenmore front-load washers built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, leave standing water in the tub, stop mid-cycle, display error codes 5C, SE, nd, 5E, or 4E, or make loud grinding or humming noises during the drain phase. The DC97-20621C is the current production revision of this pump, which also covers the earlier DC97-20621A variants — all three are the same pump in successive production runs. It also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830. Before ordering, always check the drain filter/coin trap at the bottom front of the washer — a clogged filter is a common cause of drain error codes that does not require pump replacement. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC97-20621C Washer Drain Pump Assembly fixes Samsung front-load washers displaying error codes 5C, SE, nd, 5E, or 4E, not draining, leaving standing water, or making loud grinding or humming noises during the drain cycle. Covers DC97-20621A and DC97-20621B variants. Compatible with select Samsung series and Kenmore (Samsung-built). Replaces DC97-20621A, DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, EAP12592830. Check drain filter before replacing pump. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, nd, 5E, or 4E displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — pump motor running but not pumping Grinding or rattling noise during drain — damaged impeller or worn pump bearings Water draining very slowly — worn pump below rated performance Clothes excessively wet after a cycle — pump not fully removing water before spin Water leaking from the pump area at the front bottom of the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: DC97-17999N, DC97-20621A, 03DC31-00187A, AP7366238, ASM105564, PFIX17701443, PD00095227, PX3516-01, PS17701443, AP6807020, PS12592830. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select Samsung front-load washers and related Kenmore models: Samsung series — WF50R8500AW, WF45T6200AW, WF53BB8900 and related models Kenmore / Sears front-load washers (select Samsung-built models) Important: Before replacing the pump, check and clean the drain filter/coin trap located behind the lower access panel at the front of the washer. A clogged filter causes the same error codes as a failed pump and is the most common fixable cause of Samsung front-load drain errors. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Resolves Samsung error codes 5C, SE, nd, 5E, and 4E caused by drain pump failure DC97-20621C is the current production revision — covers DC97-20621A and DC97-20621B as well Also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830 Compatible with select Samsung series and Kenmore Samsung-built front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC97-20621C Also Covers DC97-20621A (prior revisions) Part Type Front-Load Washer Drain Pump Assembly Condition Aftermarket Replacement Application Samsung Front-Load Washers  Error Codes Resolved 5C, SE, nd, 5E, 4E Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel. Remove the lower kick panel screws to expose the drain filter and pump area. First, drain residual water by removing the drain filter cap (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the hose clamps and disconnect the drain hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Install the new DC97-20621C pump in the same position, reconnect drain hoses and secure clamps, reconnect the wiring harness, and reinstall the front panel. Restore power and water and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What is the difference between DC97-20621C and DC97-20621A? These are successive production revisions of the same Samsung front-load washer drain pump assembly. DC97-20621A was the original version, DC97-20621B was an intermediate revision, and DC97-20621C is the current production part. All three are the same pump with minor manufacturing changes across production runs — they are fully interchangeable. If your washer's parts diagram or old pump label shows any of these numbers, this replacement covers all of them. What error codes indicate a drain pump failure on Samsung front-load washers? Error codes 5C, SE, nd, 5E, and 4E on Samsung front-load washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the pump, clean the drain filter/coin trap at the front lower access panel — lint, coins, and debris in the filter are among the most common causes of these error codes. If the filter is clean and the errors persist, the pump itself has failed and needs replacement. Where is the drain filter on my Samsung front-load washer? The drain filter (also called the coin trap) on Samsung front-load washers is located behind the lower front access panel, typically on the right side. Remove the lower kick panel by pressing the release tab or removing the screws. You will see a small cap or twist-out cover — that is the filter. Place a shallow pan under it and slowly unscrew the cap to allow water to drain out. Remove any debris from the filter, then replace the cap and reinstall the panel. Run a cycle to check if the error clears. If the filter was clogged, this may be all the repair needed. My washer makes a loud noise during draining — is it the pump? A loud humming or grinding during the drain cycle is a common sign of a failing pump. Humming without water movement means the motor is running but the impeller is not pumping — either jammed by debris or mechanically failed. Grinding suggests worn pump bearings or a damaged impeller. Check the drain filter first for foreign objects. If the filter is clear and the noise persists, the pump needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the specifications and performance of the original DC97-20621C drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11590294 Gas Oven Igniter The XPARTCO W11590294 is an aftermarket replacement flat-style silicon carbide gas oven igniter compatible with select Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges in the WFG, AGR, VRGW, and related series. The oven igniter is a silicon carbide heating element mounted next to the oven burner tube. When a bake or broil cycle is started, the igniter draws electrical current through the gas safety valve, which holds the valve open — and simultaneously heats to ignition temperature to light the gas. The igniter must draw at least 3.2 amps to hold the gas valve fully open; as the silicon carbide element ages and weakens, it draws progressively less current, causing the oven to take too long to light, not light at all, or glow without ever opening the gas valve. This flat-style igniter is rated 3.3–3.6 amps at 120V and measures approximately 4" wide x 1" high. It features a silicon carbide element, high-temperature ceramic housing, and metal bracket. The current part number W11590294 directly supersedes W11208965, W11613927, and W11506321 — all four are the same igniter across successive production revisions. It also replaces 4977065, AP7193166, PS16744629, and EAP16744629. Pre-attached wire connectors included. Note: do not touch the silicon carbide element with bare hands — skin oils cause premature burnout. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W11590294 Gas Oven Igniter fixes Whirlpool-family gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat silicon carbide igniter, 3.3–3.6A, 120V, approx. 4"W x 1"H. Do not touch element with bare hands. Replaces W11208965, W11613927, W11506321, 4977065, AP7193166, PS16744629. Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and more. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange or red but the oven burner never lights Oven takes more than 90 seconds to ignite — igniter too weak to fully open the gas valve Oven preheats very slowly — weakened igniter limiting gas valve opening Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11590294, W11208965, W11506321, W11613927, AP7193166, AWP45526, EAP16744629, PD00083398, PS16744629. W11590294 is the current production part number superseding W11208965, W11613927, and W11506321 — all four are the same igniter. If your parts diagram shows any of these numbers, this replacement is correct. Contact our support team with your model number if you need confirmation before ordering. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands and series: Whirlpool gas ranges — WFG320 series (WFG320M0MB0, WFG320M0MS0, WFG320M0MW0 and related models) Whirlpool gas ranges — WFG505 series (WFG505M0BS4, WFG505M0BW3, WFG505M0MB0, WFG505M0MS0, WFG505M0MW0 and related models) Amana gas ranges — AGR4203 series (AGR4203MNB0, AGR4203MNW0 and related models) Amana gas ranges — AGR6303 series (AGR6303MMB0, AGR6303MMW0 and related models) Crosley gas ranges — VRGW series (VRGW3150RB0, VRGW3150RW0, VRGW3162RB0, VRGW3162RS0, VRGW3162RW0 and related models) Maytag gas ranges (select models) KitchenAid gas ranges (select models) Jenn-Air gas ranges (select models) Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the gas safety valve to hold it open so gas can flow to the burner Draws 3.3–3.6 amps at 120V — correct amperage range to reliably open the oven gas safety valve on compatible models Dimensions: approximately 4" wide x 1" high Silicon carbide element, high-temperature ceramic housing, metal mounting bracket Pre-attached wire connectors included — direct plug-in installation on compatible models Current production part superseding W11208965, W11613927, and W11506321 Do not touch the silicon carbide element with bare hands — skin oils cause premature burnout Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and related brands Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPW11590294 Supersedes W11208965, W11613927, W11506321 Part Type Gas Oven Flat Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Igniter Style Flat silicon carbide element Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Dimensions Approximately 4" W x 1" H Material Silicon carbide / Ceramic / Metal / Plastic Color White / Silver Connector Pre-attached wire connectors Handling Note Do not touch element — skin oils cause premature burnout Compatible Brands Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas range. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. ⚠️ Handle With Care — Do Not Touch the Igniter Element The silicon carbide igniter element is fragile and sensitive to skin oils. Handle only by the bracket and wiring — never touch the silicon carbide element itself. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel to expose the burner assembly. Locate the old igniter mounted next to the oven burner tube. Disconnect the igniter's wire connectors and remove the two mounting screws securing the bracket. Note the wire routing inside the range cavity before removing — be careful not to let the burner wires fall back into the range body. Connect the new W11590294 igniter's pre-attached connectors to the matching wires from the range. Mount the new igniter in the same position with the two bracket screws. Reinstall the oven bottom panel and racks. Restore gas and power, then run a bake cycle and confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the relationship between W11590294, W11208965, W11613927, and W11506321? These are all part numbers for the same gas oven igniter across successive production revisions by Whirlpool. W11506321 was an earlier version, W11613927 and W11208965 were subsequent updates, and W11590294 is the current production number. All four are the same flat silicon carbide igniter with the same specifications, dimensions, and function. If your range's parts diagram or old igniter shows any of these numbers, this replacement covers all of them. My oven igniter glows but the burner never lights — is this the right part? Yes — an igniter that glows but fails to light the burner is the most common symptom of a weakened igniter. The gas safety valve requires at least 3.2 amps of current draw through the igniter to hold it open. As the silicon carbide element ages, it draws less current — eventually reaching a point where it glows visibly but no longer draws enough current to fully open the gas valve. If the igniter glows for more than 90 seconds without the burner lighting, it needs replacement. The W11590294 is rated 3.3–3.6 amps, which is the correct range to reliably activate the safety valve on compatible models. What is the difference between W11590294 and W11176454? Both are flat silicon carbide oven igniters for Whirlpool-family gas ranges, but for different model series. The W11590294 is used on the WFG320, WFG505, and related entry-level Whirlpool and Amana gas ranges. The W11176454 (which replaces W10914411) is used on higher-end Whirlpool, Amana, and Maytag models across a broader range of WFG, MGR, and related series. They have the same amperage rating and igniter style but are not always interchangeable — always verify your model number before ordering to confirm which igniter is correct for your range. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, the igniter is too weak. For a more precise test, use a multimeter in resistance mode — disconnect the igniter and measure resistance across the element. A working W11590294-style igniter typically reads between 40–100 ohms at room temperature. An open circuit (infinite resistance) means the element has burned through completely. You can also test in operation by measuring current draw at the igniter circuit — a reading below 3.2 amps indicates the igniter is too weak to reliably open the gas valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original W11590294 gas oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11612326 Dishwasher Circulation Pump (OE) OE-style dishwasher circulation pump designed to move water through the spray arms and restore proper dishwasher wash performance. ✓ Dishwasher Repair Part ✓ Replaces W11612326 ✓ Compatibility Support Product Description The XPARTCO W11612326 Dishwasher Circulation Pump moves water through the dishwasher spray arms during the wash cycle. A faulty circulation pump can cause poor cleaning, weak water pressure, unusual pump noise, or incomplete wash performance. Replacing a failed dishwasher circulation pump can help restore proper water circulation and improve dishwashing results. What is OE ?:  “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. They offer identical fit and function to OEM (Original Equipment Manufacturer) components but are typically sold under independent brands like XPARTCO for better affordability. Quick Answer If your dishwasher is not cleaning properly, has weak spray arm pressure, or makes unusual pump noise, the W11612326 circulation pump may need replacement. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not cleaning dishes properly Weak spray arm water pressure Water not circulating during wash cycle Unusual circulation pump noise Poor dishwasher wash performance Replaces part Number W11612326, W10879262, W10805386, W11521435, AP7193729, PS16744934, 4460096, AP6027386, AWP45622, AP16744934, PD00080710, PS11759751. Compatibility This part fits select Whirlpool, KitchenAid, Maytag, Amana, and compatible dishwasher models using part number W11612326. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Dishwasher circulation pump replacement Helps restore proper water circulation Supports spray arm water pressure Designed for compatible dishwasher models “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. Product Specifications Brand XPARTCO Part Type Dishwasher Circulation Pump Primary Part Number W11612326-OE Compatible Appliance Type Dishwasher Condition New Installation Disconnect power and water supply before installation. Inspect hoses, seals, and wiring connections after installation. Troubleshooting Guide ⚠️ Disconnect power and water supply before servicing the dishwasher. Check spray arms and filters for blockage before replacing the pump. Inspect the circulation pump area for leaks or unusual noise. Verify wiring connections are secure. Replace the circulation pump if water circulation problems continue. When Should You Replace This Part? Replace the dishwasher circulation pump if the dishwasher has poor cleaning performance, weak spray pressure, unusual pump noise, or water is not circulating during the wash cycle. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ OE-Style Replacement ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W10498976 Refrigerator Water Inlet Valve Replaces WPW10498976 The XPARTCO W10498976 is an aftermarket replacement refrigerator water inlet valve assembly compatible with select Whirlpool, Maytag, KitchenAid, Kenmore, and Ikea bottom-freezer and French door refrigerators in the WRB, WRF, MBF, GX5, GB9, GB2, and related series. The water inlet valve is a solenoid-operated valve mounted on the back of the refrigerator that controls the flow of water from the household supply line to the ice maker and, on models with a door dispenser, to the water dispenser. When the solenoid coil burns out or the valve seat becomes clogged with mineral deposits, the ice maker stops producing ice, the water dispenser stops working, water trickles weakly, or water leaks from the valve body. Rated 120V, 50/60Hz, 35W solenoid, this valve measures 3-1/2"L x 2-3/4"W x 3"H and includes the valve body and mounting bracket. It connects via 1/4" inlet fitting to the household supply line and uses push-in tube fittings on the outlet side. It directly replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, 2315508, IMV-576, AP6022334, EAP11755667, PD00024636, PS11755667, WP2315576, and WV8047. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W10498976 Refrigerator Water Inlet Valve fixes Whirlpool-family bottom-freezer and French door refrigerators where the ice maker is not making ice, the water dispenser is not working or producing only a trickle, or water is leaking from the back of the refrigerator. 120V/50-60Hz/35W solenoid, 3-1/2"L x 2-3/4"W x 3"H, includes bracket. 1/4" inlet connection. Replaces WPW10498976, W10420082, W10498974, K-78200, 2684516, AP6022334, PS11755667. Compatible with Whirlpool WRB/WRF, Maytag MBF, KitchenAid, Kenmore, and Ikea. Common Problems This Part Fixes Ice maker not producing ice or producing very small cubes due to insufficient water supply Water dispenser not working — no water flows when the lever or button is pressed Water dispenser producing only a trickle — valve partially blocked or solenoid weakening Water leaking from behind the refrigerator near the water valve Ice maker fills but overflows — valve stuck open and not closing properly Humming sound near the back of the refrigerator when requesting ice or water — solenoid energized but valve not opening No water reaching the refrigerator despite supply line being connected and pressurized Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WPW10498976, W10498976, W10420082, AWP50873, EAP11755667, PD00024636, AP6022334, PS11755667.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select bottom-freezer and French door refrigerators from the following brands and series: Whirlpool refrigerators — WRB322, WRB329, WRF535, WRF555, and related WRB/WRF series (French door and bottom-freezer models) Maytag refrigerators — MBF1958, MBF2258, and related MBF series KitchenAid refrigerators — select bottom-freezer and French door models Kenmore / Sears refrigerators — select Whirlpool-built models Ikea refrigerators — select models (Whirlpool-built) Other Whirlpool-platform models including GB9, GB2, GX5, GX2, ET1CH, ET8CH, IX5HH, ED22, and related series Note: Always verify your exact model number before ordering — water inlet valves are model-specific and not universal across all refrigerator configurations. Check that the supply line connection size (1/4") matches your existing supply line before purchasing. Key Features Solenoid-operated valve — opens on command from the refrigerator's control board to supply water to the ice maker and water dispenser Rated 120V, 50/60Hz, 35W — correct electrical specifications for compatible Whirlpool-family refrigerators Dimensions: 3-1/2"L x 2-3/4"W x 3"H — includes mounting bracket for direct installation 1/4" inlet connection — matches standard residential refrigerator supply line diameter Push-in outlet tube fittings — easy connection to existing water supply tubing inside the refrigerator Plastic and metal construction — durable and resistant to mineral buildup Replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, AP6022334, and over 10 additional cross-references Compatible with Whirlpool WRB/WRF series, Maytag MBF series, KitchenAid, Kenmore, and Ikea refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10498976 OEM Part Number WPW10498976 Part Type Refrigerator Water Inlet Valve Assembly Condition Aftermarket Replacement Application Bottom-Freezer and French Door Refrigerators Voltage 120V AC Frequency 50/60 Hz Solenoid Wattage 35W Dimensions 3-1/2"L x 2-3/4"W x 3"H Inlet Connection 1/4 inch Color Brown / Blue / Yellow / Gray Material Plastic / Metal Includes Water valve body and mounting bracket Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the household water supply valve before beginning. Place a towel and small container under the valve area to catch residual water. Pull the refrigerator away from the wall to access the back lower panel — remove the panel screws to expose the water inlet valve. Photograph the wiring harness connections and water tube connections before disconnecting. Turn off the water supply and disconnect the 1/4" supply line from the valve inlet — use an adjustable wrench, as some compression fittings may be stuck. Squeeze the plastic retaining clips on the outlet tube fittings and pull the internal water tubes free. Disconnect the wiring harness. Unscrew the mounting bracket and remove the old valve. Install the new W10498976 valve with its bracket, reconnect the internal water tubes (push until they click), reconnect the wire harness and supply line. Restore water supply and power. Run a water dispenser test and check for leaks. Tools needed: Phillips screwdriver, adjustable wrench, needle-nose pliers. Frequently Asked Questions What does the refrigerator water inlet valve do? The water inlet valve is an electrically controlled solenoid valve that opens on command from the refrigerator's control board to allow household water pressure to push water through to the ice maker fill tube or the water dispenser. When the ice maker calls for water or you press the dispenser lever, the board sends voltage to the solenoid coil, which opens the valve. When the demand is satisfied, the voltage stops, the spring closes the valve, and water flow stops. A failed solenoid coil — or a valve seat clogged with mineral deposits — prevents the valve from opening or closing correctly, causing no water, weak water, overflow, or dripping. What is the difference between W10498976 and WPW10498976? These are the same water inlet valve. WPW10498976 is the updated Whirlpool OEM part number that superseded the original W10498976. The W10420082 and W10498974 are also cross-references for this same valve from earlier production runs. This aftermarket replacement is compatible with all of these numbers. How do I know if the water inlet valve has failed vs. something else? First confirm the household water supply valve behind the refrigerator is fully open and the supply line is not kinked. Then check the water filter — a clogged filter is one of the most common causes of weak or no water flow and is mistaken for a valve failure. If both supply pressure and the filter are good, test the valve's solenoid coil with a multimeter — a working coil reads 200–500 ohms of resistance; an open circuit confirms failure. If the solenoid tests good but the valve still does not open when the control board sends voltage, the valve seat may be physically clogged with mineral deposits and the valve needs to be replaced. My ice maker is not working but my water dispenser is fine — is it the valve? Possibly — but if the water dispenser works normally, the main valve solenoid is likely functioning. On some refrigerator configurations, the ice maker and the dispenser are controlled by separate solenoid ports on the valve assembly. If only the ice maker port has failed, the dispenser can continue working while ice production stops. Test the ice maker solenoid coil separately. However, a more common cause of ice maker failure with a working dispenser is the ice maker module, freezer temperature, or ice maker shut-off arm — rule out those causes before replacing the valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal to match the electrical specifications and dimensions of the original WPW10498976 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less