Dishwasher Gasket, Seals, Hinges & Water Valves

WD08X23477 Genuine OEM GE Dishwasher Tub Seal Gasket The WD08X23477 is a genuine GE OEM tub seal gasket designed specifically for GE dishwashers with a stainless steel tub. This gasket runs around the tub opening and creates the seal that keeps wash water contained inside the tub during the cycle rather than leaking out around the edges where the tub meets the door and surrounding cabinet structure. Over time, this seal can flatten, harden, or develop gaps from years of heat and moisture exposure, which lets water escape past the seal instead of staying inside the tub. A worn or damaged gasket typically shows up as water leaking from underneath or around the front of the dishwasher during a cycle, dampness or pooling near the base of the unit, or visible flattening, cracking, or separation in the seal material itself. It directly replaces AP6041570 and PS11774413. Quick Answer The WD08X23477 Genuine OEM GE Dishwasher Tub Seal Gasket fixes GE dishwashers with a stainless steel tub that are leaking water from around the tub opening during a cycle. Replaces AP6041570, PS11774413. This gasket is specific to stainless steel tub models — it is not the plastic tub/door gasket used on other GE dishwasher designs, such as WD08X21894 or WD08X23476. Common Problems This Part Fixes Water leaking from underneath or around the front of the dishwasher during a cycle Dampness or pooling near the base of the dishwasher after running Visible flattening, hardening, or cracking of the seal around the tub opening Gaps or separation in the gasket where it meets the tub frame Leak that appears intermittently, worse on longer or hotter cycles Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher tub seal gasket directly replaces the following OEM and cross-reference part numbers: WD08X23477, WD08X22095, WD08X20675, 4466531, WD08X20591, AGE24098, AP6041570, EAP11774413, PD00052582, PS11774413 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This tub seal gasket is compatible with select GE dishwashers equipped with a stainless steel tub, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the same GE platform. Note — stainless steel tub only, and verify fit carefully: This gasket is designed specifically for GE's stainless steel tub design and is a different part from the gaskets used on plastic tub GE dishwashers (such as WD08X21894 or WD08X23476). Additionally, this seal has a documented fitment sensitivity — at least one customer has reported that on their unit, the older original seal had roughly 2 extra inches of material at the bottom that this replacement did not match, resulting in a persistent minor leak even after installation. Confirm your dishwasher has a stainless steel tub and verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified for stainless steel tub dishwashers Seals the tub opening to keep wash water contained during the cycle Resolves "water leaking from the front or underneath," "dampness near the base," and "flattened or cracked seal" symptoms Durable material designed to withstand repeated high-humidity, high-temperature cycles Direct drop-in replacement — fits the original tub opening groove Replaces AP6041570 and PS11774413 Compatible with GE, Hotpoint, Haier, Monogram, and Café stainless steel tub dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD08X23477 Part Type Dishwasher Tub Seal Gasket Condition Genuine OEM Brand GE Application Stainless Steel Tub Dishwashers Function Seals the tub opening to prevent water leaks during wash cycles Quantity 1 tub seal gasket Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Verify Seal Length Against Your Original Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access to the tub opening seal is typically from the front of the unit with the door open, though some models may require removing the door or surrounding trim to fully access the gasket channel. Before removing the old seal, take note of its full length and how it seats into the groove around the tub opening — some customers have found the replacement seal shorter than the original at one section, so compare the two side by side before discarding the old one. Carefully pull the old gasket free from its retaining groove, working around the full perimeter. Press the new WD08X23477 gasket into the same groove, working around the full perimeter and ensuring it seats evenly with no twists, gaps, or areas where it's pulled too tight. Run your fingers along the full seal after installation to confirm even, consistent contact with no visible gaps. Restore water and power, then run a test cycle and check underneath and around the front of the unit for any signs of leaking. Tools needed: flat-blade screwdriver (model-dependent access), work gloves. Frequently Asked Questions How do I know if my dishwasher has a stainless steel tub or a plastic tub? Open the dishwasher door and look at the interior tub walls — a stainless steel tub has a visible metallic finish, while a plastic tub is typically a solid plastic color (often white, gray, or black) with no metallic sheen. This gasket is designed specifically for the stainless steel tub design; plastic tub models use a different gasket. If you're not sure, check your model number against your appliance's documentation or contact our support team. I installed the new seal but I'm still seeing a small leak. What should I check? This has been reported by at least one customer, who found their original seal had extra material at the bottom that this replacement didn't fully match, resulting in a persistent minor leak. Before assuming the gasket itself is faulty, run your fingers around the entire seal after installation to check for any spot where it isn't making even, firm contact — pay particular attention to the bottom section. If a specific area isn't sealing, it may need to be pressed more firmly into its groove, or in rare cases, your particular tub design may require a different seal than expected. Contact our support team with your model number if the leak persists after a careful reinstall. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original material, profile, and groove fit of the tub seal gasket originally installed in your stainless steel tub dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚰 DD82-01588A Dishwasher Water Inlet Valve – Genuine OEM Samsung Part 🔁 Replaces These Part Numbers DD82-01588A (primary OEM) Also Replaces PS12593084, AP6807545, DD81-02265A, AP6244375, PS12085633. Description: This Dishwasher Water Inlet Valve Assembly is essential for regulating the water flow into dishwasher, ensuring optimal cleaning performance. This replacement Genuine OEM part is engineered to provide precise water control, preventing leaks and maintaining efficient operation. ✅ Key Features Genuine Samsung OEM part – DD82-01588A Precision-engineered to match factory standards Controls cold water intake with accurate timing and pressure Easy to install using standard tools Tested for leak-free performance 🔧 Fixes Common Symptoms Dishwasher won’t fill or fills slowly Error codes related to water inlet No water intake at cycle start Valve leaks or hums without water flow 🚚 Why Buy from Parts‑O‑Matic? ✅ Genuine OEM quality — not a knock‑off ✅ Always Fast and Free U.S. shipping ✅ Expert customer support for part fitment ✅ Trusted by DIYers and appliance professionals 🛒 Restore proper water fill and cycle reliability — order your DD82-01588A OEM water inlet valve today from Parts‑O‑Matic and enjoy speedy, free delivery.

Read more less

XPARTCO 8580309 Dishwasher Door Latch Strike Replaces WP8580309 The XPARTCO 8580309 is an aftermarket replacement door latch strike for Whirlpool-built dishwashers. This small metal component attaches at the top of the dishwasher tub and locks the door latch securely in place whenever the door is closed. It does double duty: mechanically, it's what keeps the door held shut and properly tensioned against the tub opening to maintain a watertight seal during the wash cycle, and it also acts as the actuator that trips the door switch, telling the control that the door is closed and it's safe to run. Made from durable metal, measuring approximately 2" in length. Over years of opening and closing the door, the strike can wear down, bend from an accidental impact, or simply weaken to the point where it no longer holds the latch with enough tension. Debris buildup around the strike can also interfere with proper latching. A failing strike produces a clear set of symptoms: the dishwasher won't start because the door switch never registers as closed, the door feels loose or doesn't seal tightly when shut, or water leaks out around the door during a cycle. It directly replaces WP8580309, AP6013574, 8269111, 1181203, AH1156352, EA1156352, PS1156352, and PS11746800. Quick Answer The XPARTCO 8580309 Dishwasher Door Latch Strike fixes Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Estate, Inglis, and Crosley dishwashers that won't start because the door won't latch, feel loose when closed, or leak water around the door during a cycle. Metal construction, approximately 2" long. Replaces WP8580309, AP6013574, 8269111, 1181203, AH1156352, EA1156352, PS1156352, PS11746800. Package includes small parts — keep away from young children during installation. Common Problems This Part Fixes Dishwasher won't start because the door won't latch or the door switch never registers as closed Door feels loose, doesn't seal tightly, or doesn't hold shut properly Water leaking out around the door during a wash cycle Door latch failing to catch even though the door appears closed Visible wear, bending, or damage on the strike itself Increased door-closing noise since the strike no longer cushions the latch properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher door latch strike directly replaces the following OEM and cross-reference part numbers: 8580309, WP8580309, AP6013574, 8269111, 1181203, AH1156352, EA1156352, EAP1156352 PS1156352, AWP48708, PD00004771. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door latch strike is compatible with select Whirlpool-built dishwashers across the Whirlpool family of brands, including: Whirlpool dishwashers — DP1040X, DU1055XTSS2, DU1145XTPBA Whirlpool GU series — GU1500XTKB0, GU1200XTKS0, GU1200XTLB3, GU2400XTPS3, GU1200XTKB0, GU1100XTLB1, GU1500XTLQ1 KitchenAid — KUDC02IRBL1, KUDI01DLBL2, KUDI01DLWH2, KUDL02IRBS3, KUDK01ILBS0, KUDK01ILBS1, KUDK01ILBS5, KUDK03ITBS1 Kenmore / Sears — 665.16512201, 665.16532200, 665.17533202, 665.17512200 Maytag, Amana, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Estate, Inglis, and Crosley dishwashers (select models) Note: Always verify your full model number before ordering, since Whirlpool uses several different door latch strikes across its dishwasher lineup, including the separate W10544004 / WPW10544004 strike used on other models. Contact our support team with your model number if you're unsure which strike fits your dishwasher. Key Features Aftermarket replacement door latch strike — attaches to the top of the tub and locks the door latch in place when closed Works as a mechanical actuator for the door switch, confirming to the control that the door is closed Provides the door tension needed for a proper watertight seal Resolves "won't start," "door won't latch," "loose door," and "leaking around the door" symptoms caused by strike wear or damage Durable metal construction, approximately 2" in length Direct drop-in replacement — mounts to the original tub location Replaces WP8580309, AP6013574, 8269111, 1181203, AH1156352, EA1156352, PS1156352, and PS11746800 Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Jenn-Air, and related dishwashers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8580309 OEM Part Number WP8580309 Part Type Dishwasher Door Latch Strike Condition Aftermarket Replacement Material Metal Length Approx. 2 in. Weight Approx. 0.03 lbs. Location Top of the dishwasher tub Function Locks the door latch and actuates the door switch Repair Difficulty Easy — basic hand tools, minor disassembly Quantity 1 door latch strike Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Estate, Inglis, Crosley Installation Notes ⚠️ Unplug Dishwasher Or Shut Off Breaker Before Starting Unplug the dishwasher or shut off the house circuit breaker before beginning. Wear work gloves. Open the dishwasher door and locate the door latch strike mounted at the top of the tub opening, above where the door latch engages when closed. Using a flat-blade screwdriver, remove the screws securing the old strike in place, then lift it free. Position the new 8580309 strike in the same location, aligning it so the door latch will catch and engage correctly when the door is closed, and secure it with the mounting screws. Close the door and confirm the latch catches firmly and holds the door snugly against the tub with no give. Restore power and run a test cycle, checking around the door for any signs of leaking. Tools needed: flat-blade screwdriver, work gloves. Frequently Asked Questions My dishwasher won't start even though I closed the door. Is this the strike? It's a strong possibility. This strike acts as the mechanical actuator for the door switch — when the door closes, the strike is what physically trips the switch to signal the control that it's safe to run. If the strike has worn down, bent, or weakened, the door may appear closed without properly triggering that switch, leaving the dishwasher unable to start even though nothing looks obviously wrong. Water is leaking around my door during the cycle. Could that be this part? Yes, this is a common cause. The strike provides the tension that pulls the door snugly against the tub opening to maintain a watertight seal. If it's worn or damaged, the door may close but without enough holding tension to keep the seal tight, letting water seep out around the edges during the wash. Is this the same strike used on all Whirlpool dishwashers? No. Whirlpool uses more than one door latch strike design across its dishwasher lineup — for example, the W10544004 / WPW10544004 strike is a separate part used on other models such as the WDF520PADM, WDT730PAHZ, and WDT720PADM. Always check your full model number before ordering to make sure you're getting the correct strike for your specific dishwasher. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, mounting configuration, and door-tensioning function of the original WP8580309 latch strike used in compatible Whirlpool, Kenmore, KitchenAid, and related dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD08X27458 Dishwasher Genuine OEM Floating Seal – Compatible with GE Dishwashers Product Description Prevent leaks and ensure reliable dishwasher operation with the WD08X27458 Dishwasher Genuine OEM Floating Seal. This factory-approved seal fits beneath the float assembly, helping regulate water levels and keeping water contained inside the tub. A worn or damaged seal can cause leaks or improper filling. Replacing it with this genuine OEM part restores proper performance and protects your kitchen from water damage. Replaces Part Numbers WD08X27458, WD08X25471, AP7018540, EAP16554611, PD00072539, PS16554611. Compatibility This floating seal is compatible with select GE dishwashers. Example compatible models include (but are not limited to): GE GDF530PSM0SS, GE GDT695SMJ0ES, and GE PDT825SSJ0SS. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Part – Factory-approved floating seal for GE dishwashers 💧 Leak Protection – Keeps water contained in the dishwasher tub 💰 Cost-Effective Repair – Prevents costly kitchen water damage 🛠️ Easy Installation – Installs in minutes under the float assembly 🛡️ Fixes Common Issues – Resolves dishwasher leaks and incorrect filling 📐 Product Specification Part Number: WD08X27458 Component Type: Dishwasher Floating Seal Material: Durable rubber construction Mounting: Direct-fit replacement under float assembly Operating Conditions: Designed for residential dishwasher use Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: None or Phillips screwdriver (depending on model) ⚠️ Safety First: Disconnect power and water supply before servicing the dishwasher. Steps: Disconnect dishwasher from power and water supply. Open the dishwasher door and locate the float assembly. Lift float to access the old seal beneath it. Remove worn seal and place new WD08X27458 floating seal in position. Ensure secure fit, reinstall float, and close door. Restore power and water, then run a short cycle to test. ⏱️ Time Required: 10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop leaks and protect your kitchen — Add to Cart Now for a genuine, factory-approved repair!

Read more less

XPARTCO DD94-01002A Dishwasher Mounting Installation Kit for Samsung. High-quality dishwasher mounting installation kit designed to help secure compatible dishwashers properly during installation. ✓ Dishwasher Installation Part ✓ Replaces DD94-01002A ✓ Compatibility Support Product Description The XPARTCO DD94-01002A Dishwasher Mounting Installation Kit is used to help secure compatible dishwashers during installation. Proper mounting helps keep the dishwasher stable, aligned, and safely positioned under the countertop or cabinet opening. Replacing missing, damaged, or worn mounting hardware can help restore a secure dishwasher installation and prevent unwanted movement during use. Quick Answer If your dishwasher is loose, shifting, not secured under the counter, or missing mounting hardware, the DD94-01002A dishwasher mounting installation kit may be needed. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not secured properly Missing dishwasher mounting hardware Dishwasher shifting during use Loose dishwasher installation Damaged or worn mounting brackets Replaces part Number DD94-01002A, 2077601, AP4450818, ASM941007, PD00007402, EAP4222710, PS4222710. Compatibility This part fits select Samsung and compatible dishwasher models using part number DD94-01002A. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Dishwasher mounting installation kit Helps secure dishwasher in place Supports proper dishwasher alignment Designed for compatible dishwasher models Quality aftermarket replacement part Product Specifications Brand XPARTCO Part Type Dishwasher Mounting Installation Kit Primary Part Number DD94-01002A Compatible Appliance Type Dishwasher Condition New Installation Disconnect power before installation. Follow the dishwasher installation instructions and verify the unit is level, aligned, and securely mounted before use. Troubleshooting Guide ⚠️ Disconnect power before servicing or installing the dishwasher. Check if the dishwasher is level and properly aligned. Inspect mounting brackets and screws for damage or missing hardware. Confirm the dishwasher does not shift when the door is opened or closed. Replace the mounting kit if hardware is missing, damaged, or no longer secure. When Should You Replace This Part? Replace the dishwasher mounting installation kit if the dishwasher is loose, shifting, not properly secured, or if the original mounting hardware is missing or damaged. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout ```

Read more less

WD19X25278 Dishwasher Genuine OEM Diverter Assembly Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077. Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.

Read more less

WD19X25278 Dishwasher Diverter Assembly The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning. The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK. Quick Answer The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first. Common Problems This Part Fixes Water pooling or leaking underneath the dishwasher Poor washing performance from one or both spray arms Unusual noise during the wash cycle Water not properly directed to the correct spray arm Inconsistent cleaning results between the upper and lower racks Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers: WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB. Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement diverter assembly — controls water flow to the spray arms Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms Valve and float assembly engineered to optimize water flow while minimizing noise Direct drop-in replacement matching the original mounting and connections Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair Product Specifications Part Number WD19X25278 OEM Part Number WD19X25278 Part Type Dishwasher Diverter Valve Assembly Condition Aftermarket Replacement Function Controls water flow direction to the upper and lower spray arms Design Valve and float assembly Repair Difficulty Easy to Moderate — DIY-friendly Quantity 1 diverter assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions I'm seeing water pooling under my dishwasher. Is this the part I need? Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it. Any tips to avoid damaging the new part during installation? Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this. Is this a difficult repair? No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

8270020CM Dishwasher Door Spring Door balance spring - 7.75" overall length. Fits Whirlpool dishwashers. Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.   This is an aftermarket part that can be used as a replacement for the OEM part.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less