Dishwasher Gasket, Seals, Hinges & Water Valves

W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W10844024 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers. This valve regulates the flow of water into the appliance during each fill stage of the wash cycle, opening and closing to admit the correct amount of water at the right times. Weighing approximately 0.2 lbs, common failure causes include mineral or sediment buildup inside the valve and general electrical wear in the solenoid. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, or a valve that's unusually noisy — starting and stopping repeatedly — during heavy wash cycles as it struggles to regulate flow correctly. It directly replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Quick Answer The W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers that aren't filling with water, or that are unusually noisy — starting and stopping — during heavy wash cycles. Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996. Some households need a separate hose adapter for this valve if the existing water line connector has a smaller diameter than the new valve's fitting — check before you start, or be prepared for a quick hardware store trip. Common Problems This Part Fixes Dishwasher not filling with water at all Valve unusually noisy — starting and stopping repeatedly during heavy wash cycles Cycle stalling at the fill step and never advancing to wash Poor washing results due to insufficient water fill Leaking near the valve connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W10844024, 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers built on the Whirlpool platform, including model numbers such as KUDR25SHWH1, MDB4629AWB1, DU900PWKB0, DU900PWKQ0, and Kenmore 665.15522000, 66517662991, and 66516669991. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher during each fill stage of the cycle Resolves "won't fill" and "noisy, starts and stops when filling" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Compatible with Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10844024 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Weight Approx. 0.2 lbs Function Regulates water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, Amana Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Check Your Hose Connector Size First Disconnect power at the outlet or shut off the circuit breaker, and disconnect the water lines connected to the old valve before beginning. Wear work gloves. Have a shop vacuum on hand — some customers have needed to remove standing water from the bottom of the dishwasher before starting this repair. Locate the old valve and use pliers to unscrew any screws or bolts connecting it to the appliance. Clean the area where the old valve was located, removing any debris before installing the new one. Check the diameter of your existing water line connector before starting — some households have a smaller-diameter connector than this new valve's fitting requires, in which case you'll need a separate hose adapter from a hardware store to complete the connection. Take the new W10844024 and place it in the same position as the old valve, making sure it's connected correctly, and secure any screws or bolts. Reattach the water lines to the new valve and reconnect power. Double-check all connections before restoring power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: pliers, possibly a hose adapter, shop vacuum (if needed), work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Will I need any extra parts for this installation? Possibly. A few customers have found their existing water line connector had a smaller diameter than this valve's fitting, requiring a separate hose adapter purchased locally from a hardware store to complete the connection. It's worth checking your connector size beforehand, or having a quick trip to the hardware store planned just in case. My dishwasher makes a noisy, start-and-stop sound when filling. Is that this valve? Yes, this is a documented symptom. One customer described their valve as "very noisy on heavy wash cycles, started and stopped when filling" before replacing it with this exact part, which resolved the issue. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve The WPW10327249 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers, mounted on the right-hand side of the dishwasher's interior behind the front kick plate. This valve regulates the flow of water into the appliance during each cycle, opening to admit water from the household supply and closing once the correct amount has entered, which is essential to proper filling and efficient operation. Over time, mineral or sediment buildup inside the valve body, or general electrical wear in the solenoid, can cause the valve to fail. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, water filling inconsistently or too slowly, leaking, or overfilling. It directly replaces AP6019618, W10316814, W10327249, W11130743, WPW10327249VP, 3015511, PS11752927, and W11669945. Quick Answer The WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers that won't fill with water, fill inconsistently, leak, or overfill. Located on the right-hand side of the dishwasher interior. Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter (W10685193), since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with water at all Water filling inconsistently or too slowly Dishwasher leaking near the valve area Dishwasher overfilling Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water valve directly replaces the following OEM and cross-reference part numbers: WPW10327249, W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, and Maytag dishwashers built on the Whirlpool platform, including model numbers such as WDT750SAHZ, WDTA50SAHZ, WDT710PAYM, MDB4949SDM, and MDB4949SHZ. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary in size or shape between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher during each fill cycle Resolves "won't fill," "fills inconsistently," "leaking," and "overfilling" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927 Compatible with Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Novice-friendly repair with basic hand tools Product Specifications Part Number WPW10327249 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Right-hand side of the dishwasher interior, behind the front kick plate Color Blue Water Line Connections Two 3/8" lines Repair Difficulty Medium — basic appliance repair skills Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply at the shutoff valve located behind the dishwasher before beginning. Wear work gloves. Remove the bottom front kick plate by pulling outward on the two clips located at either side of the bottom panel. Locate the water inlet valve on the right-hand side of the dishwasher interior. Disconnect the two 3/8" water lines from the old valve. Unscrew the mounting screws holding the valve in place, and carefully pull the old valve away from the dishwasher. Insert the new WPW10327249 into the dishwasher, making sure it's securely positioned, and secure it with the mounting screws. Reconnect both water lines to the new valve. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Turn the water supply back on and plug the dishwasher back into the power source. Run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: multi-screwdriver, standard pliers, adjustable wrench, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Should I check or replace the water supply adapter while I have the dishwasher open? It's a reasonable idea, since the water supply adapter is a related component located in the same general area and is easy to inspect while you already have access. It doesn't need to be replaced automatically, but checking its condition at the same time can save you from needing to open the dishwasher back up again soon after if it's also showing wear. My dishwasher is leaking near the valve. Could hard water be a factor? Yes, mineral and sediment buildup from hard water is a common contributor to valve failure over time, since it interferes with the valve's ability to seal and shut off properly. Using a dishwasher cleaner periodically to help reduce limescale buildup can support the longevity of the new valve, though it isn't a substitute for replacing a valve that has already failed. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link The WD14X10009 is a Genuine OEM GE replacement dishwasher hinge arm link compatible with an exceptionally wide range of GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers — it fits over 2,100 models. The hinge arm link is the small plastic connector that joins the door spring to the door hinge arm at the bottom of the dishwasher door. This tiny part carries a big load: it's what allows the spring to counterbalance the weight of the door — especially when the door is open with a fully loaded lower rack resting on it. Without an intact link, the spring can't do its job, and the door drops open under its own weight instead of lowering in a smooth, controlled motion. The hinge arm link is a small piece of white plastic approximately 1-1/2" long, weighing about 0.01 lbs. It fails from ordinary wear and tear — thousands of open/close cycles gradually stress the plastic until it cracks or snaps. As a Genuine OEM part manufactured by GE to factory specifications, the WD14X10009 directly replaces AP2039321, 270839, AH259336, EA259336, and PS259336. Important: your dishwasher has a door spring and hinge arm link on BOTH the left and right sides. This part is sold individually — if one link has broken from age, the other is the same age and often not far behind, so many customers order two and replace both while the dishwasher is pulled out. Installs in 15–30 minutes with basic hand tools. Quick Answer The WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link fixes GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore dishwashers where the door falls open instead of lowering gently, the door won't stay shut or won't latch, the door is hard to open or close, or the door slants when open. Small white plastic link ~1-1/2" long — connects the door spring to the door hinge arm. Genuine OEM. Sold individually. Replaces AP2039321, 270839, AH259336, EA259336, PS259336. Fits 2,100+ GE-platform dishwasher models. There's one link on EACH side of the door — consider ordering two. Common Problems This Part Fixes Dishwasher door falls open instead of lowering in a smooth, controlled motion — no counterbalance from the spring Door drops down hard when opened — link broken, spring disconnected Door won't stay shut, or opens unexpectedly Door won't latch or lock properly Door is difficult to open or close Door slants or hangs unevenly when open Hinge arm link visibly cracked, bent, broken, or significantly worn Broken plastic link found lying on the floor beneath the dishwasher Door spring disconnected and hanging loose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher hinge arm link directly replaces the following OEM and cross-reference part numbers: WD14X10009, AGE24269, AP2039321, 270839, AH259336, EA259336, EAP259336, PD00023035, PS259336 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hinge arm link is compatible with an exceptionally broad range of dishwashers — over 2,100 models across the following brands: GE dishwashers — the vast majority of GE dishwasher models across many generations GE Profile dishwashers (including PDW-series models) Café dishwashers (select models) GE Monogram dishwashers (select models) Hotpoint dishwashers (select models) RCA dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Kenmore / Sears dishwashers (select GE-built models) Important — There Are TWO Links, One Per Side: Your dishwasher door has a spring and hinge arm link on both the left and right sides. This part is sold individually. Many customers discover the second link only after reinstalling the dishwasher — and since both links are the same age and have seen the same wear, the surviving one often breaks soon after. Consider ordering two and replacing both while the dishwasher is already pulled out. Also inspect the door hinge cable at the same time; if it's frayed, kinked, or bent, replace it too. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Hinge arm link — connects the door spring to the door hinge arm, allowing the spring to counterbalance the door's weight Enables the dishwasher door to open in a smooth, controlled motion rather than dropping open Supports the door's weight even when the lower rack is fully loaded and resting on the open door Prevents strain on the door hinges and door misalignment Small white plastic link, approximately 1-1/2" long, ~0.01 lbs Sold individually — note there is one link on each side of the door Replaces AP2039321, 270839, AH259336, EA259336, and PS259336 Fits over 2,100 dishwasher models across GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built lines Inexpensive fix for a problem that would otherwise cost a service call — many customers report the entire repair takes about 15 minutes DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WD14X10009 Part Type Dishwasher Hinge Arm Link (Door Spring Link) Condition Genuine OEM Application Dishwashers (GE platform) Length Approximately 1-1/2" Weight Approximately 0.01 lbs Color White Material Plastic Function Connects the door spring to the door hinge arm Location Bottom of the dishwasher door hinge, both left and right sides Quantity Sold individually (dishwasher uses TWO — one per side) Model Coverage Over 2,100 models Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. Remove the screws holding the bottom kick plate (a nut driver works well here) and the anchor screws at the top of the dishwasher that secure it to the countertop. Carefully pull the dishwasher out 8–10 inches from the cabinet to expose the door springs and hinge arm links at the bottom on both sides. (Depending on how the dishwasher is plumbed, you may be able to do this without disconnecting the water supply, drain line, or electrical — pull only as far as the connections allow, and disconnect them only if necessary for access.) Look at the hinge assembly at the bottom of the door: you'll see a steel cable with a hooked end, a spring, and the small white plastic link that ties them together. If the link is broken, it may already be lying on the floor. Remove the old link by disconnecting it from the hinge and spring — if it's cracked but still in place, you can break the remaining pieces free. Install the new WD14X10009: place the hinge arm link into the spring, hook the spring onto the clip, and seat the link into the clip on the hinge arm. Note: on some models the crimped hook opening on the steel cable is tight — if the new link won't slide in easily, a small file can carefully open the hook opening enough to accept it. Check the other side of the door while you're in there — there's a second spring and link, and if it's aged or cracked, replace it now. Push the dishwasher back into place, reinstall the anchor screws and kick plate, restore power and water, and test the door: it should now lower smoothly under spring tension rather than falling open. Tools needed: Nut driver, Phillips screwdriver, small file (occasionally), work gloves. Frequently Asked Questions My dishwasher door falls open instead of lowering gently — is this the part? Almost certainly, yes. The door spring is what counterbalances the door's weight so it lowers in a controlled motion. The hinge arm link is the small plastic piece that connects that spring to the door hinge arm. When the link cracks or snaps, the spring is effectively disconnected — so the door has no counterbalance and drops open under its own weight. This is the classic symptom. To confirm, pull the dishwasher out a few inches and look at the bottom hinge area on each side: if a link is broken, you'll often find the pieces on the floor or the spring hanging loose. If both links are intact, check the door hinge cable for fraying or the spring for damage. Should I order one or two? Order two. Your dishwasher has a door spring and hinge arm link on both sides of the door — and this part is sold individually. Many customers order one, replace the broken link, push the dishwasher back into the cabinet, and only then realize the second link exists (and is the same age, with the same wear). Since the tedious part of the job is pulling the dishwasher out from under the counter, replacing both links while you're already in there is the smart move. At a few dollars each, having a spare on hand is cheap insurance against doing the whole job over in a few months. Why do these little plastic links break? Ordinary wear and tear. The hinge arm link is a small plastic component that carries a surprising amount of load — every time you open the door, it transmits the spring's counterbalancing force to the hinge arm, and that load increases dramatically when the lower rack is fully loaded and resting on the open door. Over thousands of open/close cycles across years of use, the plastic fatigues and eventually cracks or snaps. It's a consumable wear item on GE dishwashers, which is exactly why GE uses the same inexpensive part across 2,100+ models. Do I have to disconnect the water and electrical to pull the dishwasher out? Often not. Many customers find that removing the top anchor screws and the bottom kick plate, then sliding the dishwasher out 8–10 inches, gives enough access to reach the hinge arm links — without disconnecting the water supply, drain hose, or electrical. It depends on how much slack your installer left in those lines. Pull the dishwasher out only as far as the connections allow, and see whether you can reach the hinge area. If the lines are too short and you can't reach, you'll need to disconnect the water supply, drain tube, and electrical (turn off power and water first). Either way, the link replacement itself takes only a few minutes once you can reach it. Should I replace the door hinge cable at the same time? Inspect it, and replace it if it shows any damage. The door hinge cable is the steel cable that connects the door spring assembly to the door hinge — it works alongside the link and spring in the same counterbalance system. If the cable is frayed, kinked, bent, or its crimped hook end is damaged, it will fail soon and you'll be pulling the dishwasher out again. Since you already have access, this is the ideal moment to check it. Also inspect the door spring itself for stretching or breakage. Contact our support team with your model number if you need the correct cable or spring part number. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same hinge arm link installed in compatible GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10542314 Dishwasher Gasket (Without Door Strike) Fits Specific Whirlpool, Kenmore, Maytag Dishwasher models. Door Gasket Only (Strike is not included) Description: This dishwasher gasket and strike kit (W10542314) is designed for a secure and leak-proof seal on your dishwasher. It ensures a tight closure and proper functioning for your appliance. Trust in XPARTCO for expert solutions and reliable performance with your dishwasher. Replaces Part Numbers:W10542314, 2409202, 8268888, W10284090, W10300589, W10350162, W10542314VP, AP5650274, PS5136129.  This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

00622058 Dishwasher Genuine OEM Water Valve  Fits Specific Bosch Dishwasher Models Description: This dishwasher Water Inlet Valve is a Genuine OEM part for specific Bosch dishwasher models. This component is responsible for controlling the flow of water into the dishwasher. It operates via electrical signals from the dishwasher's control board, opening to allow water to enter during the fill cycle and closing to prevent water from entering during other cycles. ✅ Key Features: Genuine OEM Part for Bosch #00622058 120V, 60Hz single solenoid valve Includes mounting bracket and hose connection port Durable thermoplastic construction 🔁 Replaces Part Numbers: 00622058, 1999956, 622058, AH3491417, AP4927070, EA3491417, PS3491417, PS8728724. 🔧 Fixes These Common Symptoms: Dishwasher not filling with water Low or slow water flow Water inlet error codes Humming or clicking without water intake Leaking around the valve area 🧰 Compatible With: ✔️ Bosch✔️ Thermador✔️ Gaggenau✔️ Siemens(Check your model number or contact us for assistance.) ✅ Affordable aftermarket solution ✅ Always Fast and Free U.S. shipping ✅ Backed by helpful support and easy returns ✅ Trusted by DIYers and appliance techs 🛒 Restore your dishwasher’s performance — order the 00622058 water inlet valve today from Parts-O-Matic.com, and get it delivered fast and free.

Read more less

XPARTCO 00619985 Dishwasher Mounting Bracket Kit - Compatible with Bosch, Thermador, Gaggenau, Kenmore Dishwashers Product Description Secure your dishwasher with the replacement XPARTCO 00619985 Mounting Bracket Kit. This kit provides sturdy brackets to fasten select Bosch, Thermador, Gaggenau, and Kenmore dishwashers to kitchen cabinets or countertops, ensuring stability and preventing tipping. It addresses issues like loose mounting, excessive vibration, or noise during operation, offering a cost-effective alternative to OEM parts. Note: Includes two mounting brackets and mounting screws (for top or side installation). Disconnect power before installation. Verify countertop or cabinet suitability for mounting. Replaces part numbers: 00619985, 00628371, 00605007, 1567804, 605007, 619985, 628371, AH3478789, EA3478789, PS3478789, PD00000071, AP4538351, PS8728568. Compatibility: Compatible with models including but not limited to: Bosch: SHX88PW55N/01, SHX89PW55N/01, SHX33M06UC/46, SHX33M05UC/46, SHX33M02UC/53, SHX33M02UC/52, SHX33M02UC/50, SHX33M02UC/46, SHEM3AY55N Thermador: DWHD94EP/50 Gaggenau: Select models requiring 00619985 Kenmore: Select models requiring 00619985 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Bosch, Thermador, Gaggenau, and Kenmore dishwashers. 🔥 Specifications: replacement mounting bracket kit, includes two stainless steel brackets and two 1.5" hex-head screws for top or side mounting. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, wrench, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves loose or unstable mounting, excessive vibration, or noise during operation. Product Specification Part Number: XP619985 Component Type: Mounting bracket kit Material: Stainless steel Weight: 3.0 oz (kit) Mounting Hardware: Includes two 1.5" hex-head screws Operating Conditions: Suitable for high-humidity kitchen environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dishwasher from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher stable and secure today! Add to cart now for a budget-friendly fix!

Read more less

AEC74337401 Dishwasher Water Inlet Guide - Compatible with LG Dishwashers Product Description Restore your dishwasher’s cleaning performance with the AEC74337401 Water Inlet Guide from Parts-O-Matic. This genuine OEM replacement guide directs water from the inlet valve into the dishwasher tub, ensuring proper water flow for wash and rinse cycles. Designed for LG dishwashers, it fixes issues like insufficient water, poor cleaning, or water inlet error codes.  Note: Includes one water inlet guide. Take photos of connections during disassembly and clean the inlet valve before installation. Replaces part numbers: AEC74337401, AP6233501, PD00056036, PS12078211. Compatibility: Compatible with models including but not limited to: Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand Compatibility: Fits select LG dishwasher models. 💧 Specifications: OEM plastic water inlet guide, designed for secure water flow and durability. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Reliable Fixes: Resolves insufficient water, poor cleaning, or water inlet error codes. Installation Notes: Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Clean the inlet valve and hose to prevent clogs. Access the inlet guide (inside or near the bottom of the dishwasher), disconnect the old guide, and install the new one, ensuring tight connections. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W11434044 is a Genuine OEM Whirlpool replacement dishwasher water inlet valve assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, and Caloric dishwashers. The water inlet valve is mounted at the base of the dishwasher and connects to the household cold water supply line. When the control board calls for water during the fill cycle, the valve's internal solenoid opens, allowing water to flow into the tub. The valve closes the instant the control board cuts power, stopping flow precisely when the correct water level is reached. Without a properly functioning inlet valve, the dishwasher can't get water into the tub — meaning it can't wash, rinse, or complete a cycle. Rated 120V AC, 50/60Hz, 6/5W. Approximate dimensions: 2.9" H x 2.3" W with a 0.9" threaded orifice for the water supply connection. The package includes the water inlet valve, water outlet pipe (inlet hose), and two hose clamps — everything needed for the connection between the valve and the dishwasher's water divider. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11434044 directly replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, and PS16217908. Important: the water inlet connection uses plastic threads, which are easily damaged by over-tightening or cross-threading — hand-tighten the water line carefully during installation. Installs in 30–45 minutes with basic hand tools. Quick Answer The W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Maytag, KitchenAid, JennAir, and Kenmore dishwashers that aren't filling with water, fill slowly, aren't washing properly, drain immediately after filling, or leak at the valve. 120V AC, 50/60Hz, 6/5W. Approximately 2.9"H x 2.3"W. Genuine OEM. Includes inlet valve, water outlet pipe, and 2 hose clamps. Replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, PS16217908. Compatible with WDT750SAKZ, KDTM404KPS, MDB4949SKZ, WDTA50SAKZ, KDTE204KPS, WDPA70SAMZ, WDPS7024, WDT740SAL, WDT751SAP, WDT970SAK series and related models. Plastic-thread inlet connection — hand-tighten carefully to avoid stripping. Common Problems This Part Fixes Dishwasher not filling with water — valve solenoid not opening when commanded Dishwasher filling too slowly — valve partially clogged with sediment or weak solenoid Dishes not being washed properly due to insufficient water fill Dishwasher fills but doesn't reach normal water level Water leaking from the valve body or its connections Dishwasher continuously running water even when the cycle should be complete — valve stuck open Dishwasher won't advance past the fill phase due to insufficient water detection Excessive cycle times as the dishwasher tries to fill from a partially clogged valve Multimeter test on the valve solenoid shows no continuity Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11434044, W11025970, W11025972, W11187724, AP6987233, AWP44732, EAP16217908, PD00064823, PS16217908. W11434044 is the current OEM production part superseding W11187724, W11025972, and W11025970. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: Whirlpool dishwashers — WDPA70SAMZ0, WDPA70SAMZ2, WDPA70SAMZ3, WDPS7024RV0, WDPS7024RZ0 series Whirlpool dishwashers — WDT740SALB2, WDT740SALB3, WDT740SALW2, WDT740SALW3, WDT740SALZ3 series Whirlpool dishwashers — WDT750SAKB0/B2/B3, WDT750SAKV0/V2/V3, WDT750SAKW0/W2/W3, WDT750SAKZ0/Z2/Z3 series Whirlpool dishwashers — WDT751SAPZ0, WDT751SAPZ1 series Whirlpool dishwashers — WDT970SAKV2, WDT970SAKV3, WDT970SAKZ2, WDT970SAKZ3 series Whirlpool dishwashers — WDTA50SAKB0/B2/B3, WDTA50SAKT0/T2/T3, WDTA50SAKV0/V2/V3, WDTA50SAKZ0/Z2/Z3 series KitchenAid dishwashers — KDTM404KPS, KDTE204KPS and related models Maytag dishwashers — MDB4949SKZ and related models JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric — select Whirlpool-built dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles Solenoid-actuated — opens precisely when the control board calls for water and closes the moment the call is dropped 120V AC, 50/60Hz, 6/5W — correct electrical specifications for compatible Whirlpool-platform dishwashers Dimensions: approximately 2.9" H x 2.3" W · 0.9" threaded orifice diameter Includes water inlet valve, water outlet pipe (inlet hose), and 2 hose clamps for a complete connection set Current OEM production part — supersedes W11187724, W11025972, and W11025970 Also replaces AWP44732, AP6987233, and PS16217908 Compatible with Whirlpool WDT740SAL, WDT750SAK, WDT751SAP, WDT970SAK, WDTA50SAK, WDPA70SAMZ, WDPS7024 series and select KitchenAid, JennAir, Kenmore, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, and related Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W11434044 Supersedes W11187724, W11025972, W11025970 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Voltage 120V AC Frequency 50/60 Hz Wattage 6/5W Dimensions Approximately 2.9" H x 2.3" W Threaded Orifice Diameter 0.9" Inlet Thread Material Plastic (hand-tighten carefully to avoid stripping) Body Material ABS Plastic / Stainless Steel Includes 1x Inlet Valve, 1x Water Outlet Pipe, 2x Hose Clamps Compatible Brands Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves — DON'T OVER-TIGHTEN PLASTIC THREADS Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Have towels ready — residual water remains in the supply line and will spill when disconnected. Critical: the W11434044's water supply connection uses plastic threads. Multiple installers have reported stripping the plastic threads by over-tightening or cross-threading the water line during installation — always hand-tighten the fitting carefully and align the threads squarely before tightening. If your dishwasher is installed under a counter, working through the lower access panel is possible but tight — many installers find it easier to pull the dishwasher partially out from the cabinet, or lay it on its side, to reach the inlet connection cleanly (this also lets you use a 90-degree hose fitting without cross-threading). Remove the lower access panel (typically 2 screws) at the front bottom of the dishwasher. Locate the water inlet valve. Photograph the wire harness and hose connections before disconnecting anything. Disconnect the household water supply line from the valve. Squeeze the hose clamps with pliers and slide them back to release the outlet hose from the valve, then disconnect the wire harness plug. Remove the mounting screws holding the valve in place. Install the new W11434044 valve, secure the mounting hardware, and reconnect the outlet hose and hose clamps. Push the electrical connector's fixing plate firmly into place before connecting the wire harness plug — this prevents the connector from falling out during operation. Reconnect the household water supply — hand-tighten the fitting carefully to avoid stripping the plastic threads. Restore water and power. Run a test cycle and check for leaks at all connections. Tools needed: Phillips screwdriver, adjustable wrench (used lightly on plastic threads only!), channel-lock pliers, work gloves, safety glasses. Frequently Asked Questions My dishwasher isn't filling with water — is the inlet valve the problem? Very likely, yes — that's the most common symptom of a failed dishwasher water inlet valve. Before replacing, do a few quick checks: 1) confirm the household water supply to the dishwasher is turned on at the shutoff valve; 2) check the household water pressure at a nearby fixture (a nearby faucet) to make sure your home has normal pressure; 3) inspect the inlet screen on the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean but the dishwasher still won't fill, the W11434044 valve solenoid has likely failed and replacing it will resolve the issue. You can also test the solenoid with a multimeter — no continuity means the solenoid has burned out. What is the difference between W11434044 and W11025970/W11025972/W11187724? These are the same water inlet valve across production revisions. W11025970 was the original OEM part number, W11025972 and W11187724 were mid-generation revisions, and W11434044 is the current OEM production version. All are physically and functionally interchangeable — if your dishwasher's parts diagram or the part on your appliance shows any of these numbers, the W11434044 is the correct current replacement, and this listing covers all of them. Why is over-tightening the water line connection such a common issue? The water supply inlet on the W11434044 has plastic threads to reduce cost and simplify manufacturing — but plastic threads are much less forgiving than brass or metal fittings. Cross-threading (starting the fitting at an angle instead of straight-in) or applying too much torque with a wrench will strip the plastic threads or split the fitting. Always align the water line fitting carefully by hand first, get several turns of engagement before applying any tool, and use only enough torque to snug the connection (typically hand-tight plus a very light quarter-turn with a wrench). If the threads are already stripped, the valve or a replacement plastic fitting will need to be ordered — the connection can't be repaired. Should I lay the dishwasher on its side for this repair? If you're finding it difficult to reach the water inlet connection cleanly through the lower access panel — which is a common complaint from installers — laying the dishwasher on its side (or pulling it partially out from the cabinet) makes the connection much easier to work with. This is especially helpful if your water supply line uses a 90-degree hose fitting that needs a straight approach for correct thread engagement. Before laying the dishwasher down, disconnect all connections and drain any residual water from the tub to avoid spills. Note that if the door has been damaged or bent, laying the unit on its side can worsen the damage — inspect first. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same water inlet valve installed in compatible Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, and related Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less