Dryer Door Latches, Switches & Knobs

17438000001584 Genuine OEM Midea Dryer Belt Safety Switch The 17438000001584 is a Genuine OEM Midea replacement belt safety switch compatible with select Midea, Criterion, and Insignia electric and gas dryers. This safety switch is positioned near the drive belt and tensioner pulley assembly, where it monitors belt-related conditions and interrupts electrical flow to the motor or heating circuit if a fault or unsafe condition is detected — such as a broken or severely slipped drive belt. This is a key safety mechanism: if the belt fails and the drum can no longer be safely driven, this switch helps prevent the motor from continuing to run unsafely or the heater from continuing to operate without normal airflow from drum rotation. When this switch fails, the dryer may not start, may shut off unexpectedly during operation, or may fail to heat even though other components test correctly. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438000001584 measures 2"L x 2"W x 3"H and weighs approximately 1 oz. It is found on the same parts diagram as the drive belt, tensioner pulley assembly, and drum support components on compatible models. Installs in 30–45 minutes with basic hand tools. Quick Answer The 17438000001584 Genuine OEM Midea Dryer Belt Safety Switch fixes Midea, Criterion, and Insignia dryers that won't start, shut off unexpectedly during operation, or fail to heat despite other components testing normally. Mounted near the drive belt and tensioner pulley assembly — interrupts power if a fault or unsafe belt condition is detected. Dimensions: 2"L x 2"W x 3"H, approx. 1 oz. Genuine OEM. Compatible with Midea MLG45N3BMG, Criterion CDG41N1AW, CDG45N1AW, and related Midea-platform dryer models. Common Problems This Part Fixes Dryer not starting — safety switch not signaling normal belt/drive conditions Dryer shutting off unexpectedly partway through a cycle Dryer not heating despite the heating element, thermostat, and other components testing normal Dryer behaving erratically after a drive belt failure or replacement Intermittent power interruption during operation traced to this switch area Switch contacts failing continuity test with a multimeter Replaces Part Numbers This belt safety switch directly replaces the following part number: 17438000001584, AP7157511, PS18188483 This is the Midea manufacturer part number used across multiple Midea, Criterion, and Insignia dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This belt safety switch is compatible with select Midea, Criterion, and Insignia dryers, including: Midea MLG45N3BMG gas dryer Midea MLG45N1BWW, MLG45N3BWW, and related MLG gas dryer series Midea MLE series electric dryers (select models) Criterion CDG41N1AW, CDG45N1AW gas dryers (air vent series) Insignia electric and gas dryers built on the Midea platform (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Safety switch mounted near the drive belt and tensioner pulley assembly Interrupts electrical flow to the motor or heating circuit if a fault or unsafe belt-related condition is detected Compact design: 2"L x 2"W x 3"H, approximately 1 oz Compatible with Midea MLG/MLE series, Criterion CDG series, and Insignia Midea-built dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 17438000001584 Part Type Dryer Belt Safety Switch Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Dimensions 2"L x 2"W x 3"H Weight Approximately 1 oz Location Near drive belt and tensioner pulley assembly Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum, drive belt, and tensioner pulley assembly. Locate the belt safety switch in this area — refer to your model's parts diagram to confirm its exact mounting position, as it is positioned near the belt and tensioner pulley support. Photograph the wire connections before disconnecting. Disconnect the wires from the old switch, remove the mounting screw or clip, and pull the switch free. Install the new 17438000001584 switch in the same position, secure the mounting hardware, and reconnect the wires. While this area is open, it's a good time to inspect the drive belt and tensioner pulley for wear, since this switch is related to belt operation. Reassemble the front panel and top panel in reverse order. Restore gas and power, and run a test cycle to confirm the dryer starts and runs normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the belt safety switch do? The belt safety switch monitors belt-related conditions near the drive belt and tensioner pulley assembly and interrupts electrical flow to the motor or heating circuit if it detects a fault or unsafe condition — such as a broken or badly slipped drive belt. This is a protective measure: if the belt has failed and the drum can no longer be driven normally, the switch helps prevent continued unsafe operation of the motor or heater. It works alongside other safety components in the dryer (like the door/cover switch and thermal limiters) as part of an overall safety system. My dryer just had a belt replacement and now isn't working right — could this switch be involved? It's possible. Since this switch is positioned near the belt and tensioner pulley assembly, it can be disturbed, dislodged, or its connector improperly reseated during a belt replacement. If your dryer is behaving erratically after a recent belt repair — failing to start, shutting off, or not heating — check that this switch's connector is fully seated and that the switch itself wasn't damaged during the repair. If the connector is good and the switch tests as an open circuit with a multimeter, it has failed and needs replacement. How do I test if this safety switch has failed? Unplug the dryer, disconnect the switch's wire connector, and set your multimeter to continuity mode. With the belt and tensioner mechanism in their normal operating position, the switch should show closed continuity (allowing current to flow). If the switch shows an open circuit when it should be closed, it has failed and needs replacement. Always refer to your specific model's wiring diagram to confirm the expected switch state, since exact behavior can vary by dryer model. Does this switch fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in certain configurations are manufactured by Midea and use the same internal components, including this belt safety switch. Confirmed Criterion models include the CDG41N1AW and CDG45N1AW gas dryers. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same belt safety switch installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11676494 Dryer Genuine OEM Knob Replaces Part Numbers: W11676494, W10215799, AP7215412, .

Read more less

🚪 XPARTCO 131658800 Dryer Door Catch This Door Catch is a replacement part for specific Kenmore, Frigidaire dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number 131658800. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit many Frigidaire, Kenmore, Electrolux, and Crosley dryers. ✅ Key Features: High-quality aftermarket replacement for part #131658800 Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: 131658800, 131658820, 131658845, 00634863, 07521419, 08015370, 134548000, 134548045, 3004967, 3202755, 3281055, 5303281055, 5307521419, 7521419, 835, AH418433, EA418433, F141735-000, F141735000, F62661-4, K1300884, K1301594, K1308079, K1309301, N8010215, Q0000401002, Q000504551, Q000504553, Q504551, Q504553, WQ504551, WQ504553, AP2107362, PS418433, WE01X25316, AP6037347, 4512762, PS11766999. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Gibson✔️ Tappan✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the 131658800 dryer door catch from Parts-O-Matic.com, and enjoy fast, free U.S. shipping!

Read more less

EXP568 Dryer Door Strike & Screw Replaces Part Number: WP8565122, 8565122, AP6013352, PS11746578, WP308685, 308685, AP6007584, PS11740701 Description: This is a replacement door strike and screw for select Maytag, Whirlpool Dryer Models.  This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

EXP571 Door Catch (Pack of 30) Pack of 30 Replaces Part Number:WP71002106, WP3389441, 3389441, 71002106, OEM18032060, AP6010685, PS11743869, OEM18024902, AP6008299, PS11741434, WE1X1195, OEM6126632, AP2042209, PS266896, 131658800, OEM6322091, AP2107362, PS418433, 5307521419, 10690002, 10690001. Description: This Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less