Featured Appliance Parts

XPARTCO WE03X37317 - WE03X37318 Dryer Drum Glide Set The XPARTCO WE03X37317 - WE03X37318 is an aftermarket replacement drum glide set for GE and Hotpoint dryers, also used on select Whirlpool and Kenmore dryers and washer-dryer combos. These plastic bearing slides are the wear pads at the front of the dryer that the drum rides on as it turns. As they wear down, the drum no longer sits and rolls smoothly, and the dryer starts to squeak, squeal, or rumble. In worse cases the drum catches or drags, and clothes can get snagged or marked between the drum and the front frame. This set pairs both glide types used on these dryers: the WE03X37317 and the WE03X37318 front bearing slides. Because the slides wear at the same rate, replacing them together restores smooth, quiet drum rotation and avoids a repeat repair. Easy to install, typically 30–60 minutes. Quick Answer The XPARTCO WE03X37317 - WE03X37318 Drum Glide Set fixes a GE or Hotpoint dryer that squeaks, squeals, or rumbles loudly as the drum turns, or whose drum drags or catches. Replaces both the WE03X37317 and WE03X37318 front bearing slides. Classic symptom: a loud squeal or scraping noise from the drum area that gets worse over the cycle, sometimes with marks or snags on clothes. Common Problems This Part Fixes Loud squeaking, squealing, or scraping noise while the drum tumbles Drum not spinning smoothly, or dragging and catching Marks, wrinkles, or snags on clothes from items catching between the drum and the front frame Excessive drum noise during drying cycles Visibly worn, thin, or chewed-up plastic glides at the front of the drum Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This glide set replaces the following part numbers: WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AGE25692, AP5668531, AP7217723, FIX17137203, PD00089026, PS6447706, PS17137203, WE03X37318, WE1M504, WE01M0333, WE1M333, TJDE504, TJWE1M333, DE504, DE775, TJDE775, AH755842, EA755842, ERWE1M333, AGE25703, AP7217724, PD00088960, PS17137205 The first group of numbers (WE03X37317, WE1M1067, WE1M316, WE1M481, WE1M507, AP7217723, PS17137203) is for the gray glide. The second group (WE03X37318, WE1M504, WE01M0504, WE01M0333, WE1M333, AP7217724, PS17137205) is for the white glide. The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility These glides are used on GE, Hotpoint, Whirlpool, and Kenmore dryers and washer-dryer combos, including models such as: GE 61140418, 61140419, 61148418, 61148419 Numerous additional GE and Hotpoint dryer and washer-dryer combo models Note: These glides fit a wide range of models, so the list above is only a sample. Compare the glides in your dryer, or your parts diagram, against the Replaces list above, or contact our support team with your model number and we'll verify fit before you order. Key Features Aftermarket replacement drum glide set covering both the WE03X37317 and WE03X37318 front bearing slides Durable plastic bearing slides that let the drum rotate smoothly Resolves squeaking, squealing, and dragging drum symptoms Helps prevent clothes from being marked or snagged at the front of the drum Replacing both glide types together avoids a repeat repair Easy installation — typically 30–60 minutes Product Specifications Part Number XPWE03X37317-WE03X37318 OEM Part Number WE03X37317, WE03X37318 Part Type Dryer Drum Glide (Front Bearing Slide) Set Condition Aftermarket Replacement Set Includes WE03X37317 and WE03X37318 Front Bearing Slides Material Plastic Application GE, Hotpoint, Whirlpool & Kenmore Dryers and Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Remove the top and front panels per your model's service guide to expose the front of the drum, and disconnect any wiring that's in the way. Lift or support the drum enough to reach the worn glides, which are held in place at the front bearing support. Pull out the old glides, noting the position and orientation of each, and fit the new ones in the same positions. Reassemble the dryer and spin the drum by hand to confirm it turns smoothly before restoring power. Replace the glides as a set, since they wear at the same rate. Frequently Asked Questions My dryer squeals or rumbles loudly while tumbling — is this the part I need? Worn drum glides are a very common cause of squeaking and scraping from the drum area. If the plastic glides look thin, grooved, or chewed up, replacing them should quiet the dryer and restore smooth rotation. Also check the drum rollers and idler pulley, which can cause similar noises. Why are there two different part numbers? GE uses two glide types at the front of the drum: glide (WE03X37317) and  glide (WE03X37318). This set covers both, so you can replace the full set in one go. Should I replace all the glides or just the worn ones? Replace them together. The glides wear at about the same rate, so if one is worn the others are usually close behind. Will this fit my Whirlpool or Kenmore dryer? These glides are cross-listed for select Whirlpool and Kenmore dryers and washer-dryer combos as well as GE and Hotpoint. Compare the part numbers on your parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X27538 Washer Drive Belt The XPARTCO WH01X27538 is an aftermarket replacement washer drive belt for GE and Hotpoint top-load washers. It is a 5-rib belt with 4 grooves, approximately 22.87 inches long. The belt connects the drive motor to the transmission pulley, so the motor can spin the basket and agitate the clothes. A worn, stretched, or broken belt can cause a washer that won't spin or agitate, a slow spin, squealing, or noise during the cycle. This is a direct-fit aftermarket replacement for the original GE belt. Belts differ between washer families, so check the part number against your model before ordering. Quick Answer The XPARTCO WH01X27538 Drive Belt fixes a GE or Hotpoint top-load washer that won't spin or agitate, spins slowly, or squeals or makes noise because the drive belt is worn or broken. Classic symptom: the motor runs, but the basket or agitator doesn't turn. Common Problems This Part Fixes Motor runs but the basket or agitator doesn't turn Washer won't spin or agitate Slow spin or poor wash performance Squealing or noise during the cycle Visibly worn, cracked, stretched, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part number: WH01X27538, 290D1101P005, 4587903, AGE25699, AP6328256, OEM18984777, PD00043350, PS12299369 Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for GE and Hotpoint top-load washers, including these examples: GE GTW220ACK4WW, GTW220ACK5WW, GTW330ASK4WW, GTW335ASN1WW GE GTW460ASJ8WW, GTW460ASJ9WW, GTW460ASJAWW Hotpoint HTW200ASK3WW, HTW240ASK5WS, HTW240ASK6WS Note: The models above are a small sample, not a full list. Washer belts differ between families, so compare your old belt to this one (approximately 22.87 inches, 5 ribs) and check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket drive belt for GE and Hotpoint top-load washers 5-rib, 4-groove design, approximately 22.87 inches long Connects the drive motor to the transmission pulley Resolves no-spin, no-agitate, and noise problems caused by a worn belt Typically a 30 minute to 1 hour repair Product Specifications Part Number XPWH01X27538 OEM Part Number WH01X27538 Part Type Washer Drive Belt Condition Aftermarket Replacement Belt Length Approx. 22.87 Inches Belt Profile 5-Rib, 4-Groove Application GE & Hotpoint Top-Load Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves before reassembling. Frequently Asked Questions My washer motor runs but the basket won't turn. Is this the part I need? A broken or slipping drive belt is a common cause. If the belt looks worn, cracked, or loose, replacing it is a good first step. How long is this belt? It is approximately 22.87 inches long, with 5 ribs and 4 grooves. If your old belt is a very different length or has a different number of ribs, check your model number before ordering. Is this a top-load or front-load part? It is listed for GE and Hotpoint top-load washers. If you are unsure which belt your washer uses, check your model number or contact our support team. Is this an easy repair? Retailers list it at roughly 30 minutes to 1 hour, though it depends on your model. Follow your model's service guide to reach the motor and pulleys. Will this fit my washer? It is listed for many GE and Hotpoint washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse Replaces WP8573713 The XPARTCO 8573713 is an aftermarket replacement thermal cut-off fuse for Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. This fuse is mounted on top of the burner funnel, directly under the drum, and it's a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant temperatures near the burner climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power. That's why a blown fuse produces such a specific symptom: the dryer won't heat, even though the drum may still tumble and the rest of the dryer seems to run normally. Because this fuse sits on the burner funnel underneath the drum rather than on the more accessible blower housing, replacing it is a more involved repair than a typical thermal fuse swap — the drum has to come out of the cabinet to reach it. Unlike a resettable thermostat, this fuse cannot be reset once it blows; it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat near the burner is exactly what this fuse is designed to react to. It directly replaces WP8573713, AP6013467, and PS11746693. Quick Answer The XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse fixes Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers that won't heat, even if the drum still tumbles normally. Mounted on the burner funnel under the drum. Replaces WP8573713, AP6013467, PS11746693. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer runs and tumbles but produces no heat Dryer that stopped heating suddenly, especially after running unusually hot Drying times that have gotten noticeably longer or clothes coming out damp Repeated blown fuses on a dryer with a known venting or airflow restriction Dryer that recently smelled like burning or overheating before losing heat Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers: WP8573713, 1180872, 8573713, AP3866211, EAP990558, PS990558, AWP49233, PD00006618 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal cut-off fuse is compatible with select Whirlpool gas dryers, and also fits select Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers built on the Whirlpool platform, including model numbers such as WGD8500SR0, and Kenmore 11070372710 and 11071112020. Note: This fuse is specific to gas dryers, mounted on the burner funnel. It is not the same fuse used on electric dryer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats Mounted on top of the burner funnel, directly under the drum Resolves "runs but won't heat," "drying takes too long," and "clothes coming out damp" symptoms caused by a blown fuse Replaces WP8573713, AP6013467, and PS11746693 Compatible with Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8573713 OEM Part Number WP8573713 Part Type Gas Dryer Thermal Cut-Off Fuse Condition Aftermarket Replacement Application Gas Dryers Location Top of the burner funnel, under the drum Resettable No — one-time use, must be replaced once blown Material Plastic housing Dimensions Approx. 1"H x 1"W Repair Difficulty Moderate to Hard — drum removal required for access Quantity 1 thermal cut-off fuse Compatible Brands Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, Sears Canada Installation Notes ⚠️ Gas Safety — Shut Off The Gas Supply Before Starting This fuse sits directly on the burner funnel, close to the gas burner assembly. Before beginning, close the gas shutoff valve behind the dryer in addition to unplugging the dryer or shutting off its circuit breaker. If at any point you smell gas, stop immediately, leave the area, and do not operate any switches — contact your gas utility or a qualified technician. Do not attempt this repair if you are not comfortable working safely around a gas appliance's burner assembly; a qualified technician can complete it instead. ⚠️ Drum Removal Required — Inspect And Clean The Venting Before Reassembling Wear work gloves. This repair requires removing the drum from the dryer cabinet to access the burner funnel, so budget more time and disassembly than a typical thermal fuse swap. Remove the top and front panels according to your model's service diagram, disconnect the drive belt from the idler pulley, and lift the drum out of the cabinet to expose the burner funnel underneath. Photograph the wiring before disconnecting the old fuse's connectors. Test the old fuse for continuity with a multimeter to confirm it's actually blown (no continuity) rather than assuming, and test the new fuse to confirm it's good out of the box. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new 8573713 fuse on the burner funnel in the same mounting position, reconnect the wiring, and reassemble the drum, belt, and panels in reverse order. Restore the gas supply and power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer tumbles fine but there's no heat. Is this the right part? Yes, this is the classic symptom of a blown gas dryer thermal cut-off fuse. Because this fuse only interrupts the heating circuit and not the drive motor, the drum can continue tumbling completely normally while the dryer produces no heat at all. If you've confirmed the burner isn't igniting and the fuse tests as an open circuit, this is very likely the fix. Why does this repair require removing the drum? My other dryer's fuse didn't need that. This particular fuse is mounted on the burner funnel underneath the drum rather than on the blower housing at the back of the cabinet, which is where many thermal fuses on other platforms are located. Reaching the burner funnel requires taking the drum out of the cabinet, which is why this repair involves more disassembly than some other thermal fuse replacements. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and mounting configuration of the original WP8573713 thermal cut-off fuse used in compatible Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WH01X27538 Washer Drive Belt The Genuine OEM GE WH01X27538 is a washer drive belt for GE and Hotpoint top-load washers. It is a 5-rib belt with 4 grooves, approximately 22.87 inches long. The belt connects the drive motor to the transmission pulley, so the motor can spin the basket and agitate the clothes. A worn, stretched, or broken belt can cause a washer that won't spin or agitate, a slow spin, squealing, or noise during the cycle. This is the original GE part. Belts differ between washer families, so check the part number against your model before ordering. Quick Answer The Genuine OEM WH01X27538 Drive Belt fixes a GE or Hotpoint top-load washer that won't spin or agitate, spins slowly, or squeals or makes noise because the drive belt is worn or broken. Classic symptom: the motor runs, but the basket or agitator doesn't turn. Common Problems This Part Fixes Motor runs but the basket or agitator doesn't turn Washer won't spin or agitate Slow spin or poor wash performance Squealing or noise during the cycle Visibly worn, cracked, stretched, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part number: WH01X27538, replaces 290D1101P005, 4587903, 5PJ 586 SJ 161, AGE25699, AP6328256, OEM18984777, PD00043350, PS12299369 Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for GE and Hotpoint top-load washers, including these examples: GE GTW220ACK4WW, GTW220ACK5WW, GTW330ASK4WW, GTW335ASN1WW GE GTW460ASJ8WW, GTW460ASJ9WW, GTW460ASJAWW Hotpoint HTW200ASK3WW, HTW240ASK5WS, HTW240ASK6WS Note: The models above are a small sample, not a full list. Washer belts differ between families, so compare your old belt to this one (approximately 22.87 inches, 5 ribs) and check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM GE drive belt for GE and Hotpoint top-load washers 5-rib, 4-groove design, approximately 22.87 inches long Connects the drive motor to the transmission pulley Resolves no-spin, no-agitate, and noise problems caused by a worn belt Typically a 30 minute to 1 hour repair Product Specifications Part Number WH01X27538 OEM Part Number WH01X27538 Part Type Washer Drive Belt Condition Genuine OEM Belt Length Approx. 22.87 Inches Belt Profile 5-Rib, 4-Groove Application GE & Hotpoint Top-Load Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves before reassembling. Frequently Asked Questions My washer motor runs but the basket won't turn. Is this the part I need? A broken or slipping drive belt is a common cause. If the belt looks worn, cracked, or loose, replacing it is a good first step. How long is this belt? It is approximately 22.87 inches long, with 5 ribs and 4 grooves. If your old belt is a very different length or has a different number of ribs, check your model number before ordering. Is this a top-load or front-load part? It is listed for GE and Hotpoint top-load washers. If you are unsure which belt your washer uses, check your model number or contact our support team. Is this an easy repair? Retailers list it at roughly 30 minutes to 1 hour, though it depends on your model. Follow your model's service guide to reach the motor and pulleys. Will this fit my washer? It is listed for many GE and Hotpoint washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP UVLIGHT LED UV Flashlight Batteries not included  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less