Dryer Fuses, Thermostats, Heaters & Igniters

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC32-00007A Dryer Thermistor - Compatible with Samsung, Kenmore, Whirlpool Dryers Product Description Maintain optimal dryer performance with the replacement DC32-00007A Dryer Thermistor. This thermistor is designed for select Samsung, Kenmore, and Whirlpool dryers, monitoring and regulating the air temperature inside the drum to ensure consistent drying. It addresses issues like no heat, overheating, insufficient heat, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermistor with two-pin connector. Disconnect power before installation.  Replaces part numbers: DC32-00007A, 2068429, N3S1-K41, N3SI-K41, DE0007A, PD00003059, EAP11741828, AP4201716, PS4204984. Compatibility: Compatible with models including but not limited to: Samsung: DV203AES, DV203AEW/XAA-0000, DV206AES/XAA-0000, DV209AEW/XAA, DV210AEW/XAA, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Whirlpool: Select models requiring 35001191 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, Whirlpool, and Skuttle dryers. 🔥 Specifications: replacement thermistor, 10K Ohms at 77°F, two-pin connector. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, overheating, insufficient heat, or premature shutoff. Product Specification Part Number: XPARTCO DC32-00007A Component Type: Dryer thermistor Material: Metal and plastic Electrical Specs: 10K Ohms at 77°F (25°C), resistance decreases with heat Mounting: Two-pin connector, 5/8" between mounting holes (center to center) Operating Conditions: Suitable for high-temperature dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO DC96-00887C – DC47-00018A Dryer Thermostat Set – Compatible with Samsung & Kenmore Dryers Product Description Restore safe temperature control and reliable drying performance with the XPARTCO DC96-00887C – DC47-00018A Dryer Thermostat Set. This high-quality aftermarket kit includes the primary operating thermostat and high-limit thermostat, designed to regulate dryer heat and prevent overheating. Faulty thermostats can cause no heat, overheating, long dry times, or repeated thermal fuse failures. Replacing both components together ensures proper heat cycling and dependable dryer operation. DC96-00887C Thermal fuse with bracket. The fuse is not resettable and will need to be replaced if blown. If the dryer does not heat, the thermal fuse may be blown. 250V, 160C, -35C. 320F Fits Samsung, Whirlpool and Kenmore dryers. DC96-00887A Replaces Part Numbers: DC96-00887C, DC96-00887A, AP5966894, PS4276292, WP35001193, 35001193, AP6008689, PS11741829. DC47-00018A  L260-50F. 125/250V. 25A. 1/4" spade terminals. Used on DC97-14486A elements. DC47-00018A Replaces Parts Numbers: DC47-00018A, AP4201898, PS4205217, 35001092, WP35001092 AP6008682, PS11741822, EXPDC47-00018A, L260-50F. Compatibility This replacement dryer thermostat set fits select Samsung and Kenmore (Samsung-manufactured) electric dryers. Example compatible models include (but are not limited to):Samsung DV210AEW, DV330AEW, DV42H5000EWKenmore 592-49045, 592-49303 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Matches OEM temperature regulation performance 🌡️ Accurate Heat Control – Maintains proper drying temperatures and prevents overheating 🔥 High-Limit Protection – Helps prevent thermal fuse blowouts 💰 Cost-Effective Repair – Reliable solution without OEM pricing 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or cycling problems 📐 Product Specification Part Numbers: DC96-00887C, DC47-00018A Component Type: Dryer Operating Thermostat & High-Limit Thermostat Set Application: Heater housing temperature regulation Material: Metal thermostat bodies with bimetal temperature discs Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and remove the rear panel. Locate the thermostats on the heater housing. Disconnect wiring and remove the old thermostats. Install the new XPARTCO DC96-00887C & DC47-00018A thermostats. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer heat control and safety — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

Genuine Whirlpool WP3392519 Dryer Thermal Fuse - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid Product Description Ensure safe dryer operation with the Genuine Whirlpool WP3392519 Dryer Thermal Fuse. This OEM thermal fuse is designed for select Whirlpool, Kenmore, Maytag, KitchenAid, and other dryers, acting as a safety device that cuts power if the dryer overheats (196°F/91°C). It addresses issues like no heat, failure to start, or premature shut-off, providing reliable performance as an authentic Whirlpool part. Note: Includes one thermal fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 3392519, WP3392519, 3388651, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PD00002311, EAP11741460, PS11741460, AP6008325 Compatibility: Compatible with models including but not limited to: Whirlpool: WED5500XW0, WED5600XW0, WED9400SW0, WGD5500XW0, WED5800BC0 Kenmore: 110.60022010, 110.68002010, 110.87872603 Maytag: MED6000XW0, MED7000XW0 KitchenAid: YKEHX01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and other dryers. 🔥 Specifications: OEM thermal fuse, trips at 196°F (91°C). 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, failure to start, or premature shut-off. Product Specification Part Number: Genuine Whirlpool WP3392519 Component Type: Dryer thermal fuse Material: Metal and plastic Electrical Specs: Trips at 196°F (91°C), one-time use, Mounting: Screw-mounted near heater housing or blower assembly Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a reliable fix!

Read more less

279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag Product Description Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278. Compatibility: Compatible with models including but not limited to: Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW Kenmore: 110.60022010, 110.70102312, 110.78002012 Maytag: MEDC215EW1, MGDX655DW1 Roper: RED4640YQ0 Estate: EED4400WQ0 KitchenAid: YKEHS01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers. 🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F). 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start. Product Specification Part Number: 279769 Component Type: Dryer thermostat kit Material: Metal and plastic Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16) Weight: 2.4 oz (Based on web:1, web:15) Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C) Mounting: Screw-mounted on heater housing. Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 280148 Dryer Thermostat Set – Compatible with Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana Dryers Product Description Restore safe and efficient drying with the XPARTCO 280148 Dryer Thermostat Set. This replacement kit includes the high-limit thermostat and thermal cutoff fuse, ensuring your dryer shuts off overheating cycles and prevents potential hazards. A faulty thermostat or cutoff can cause the dryer to overheat, stop heating, or shut down mid-cycle. This set is a cost-effective solution to restore proper dryer function. Replaces Part Numbers 280148, 1175772, 280148VP, PD00002627, FIX991443, EAP991443, AH991443, AP3874047, EA991443, PS991443, 8318314, WP8557403, 8557403, 1180102, AP6013164, PS11746386. Compatibility This dryer thermostat set is compatible with select Whirlpool, Kenmore, Maytag, Roper, Crosley, and Amana dryers. Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.66912690, Maytag MDE5500AYW. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits Whirlpool, Kenmore, Maytag, Roper, Crosley, and Amana dryers 🔒 Safety Protection – Prevents overheating and protects against dryer fires 💰 Cost-Effective Repair Kit – Includes both high-limit thermostat and thermal fuse 🛠️ Easy DIY Installation – Only requires a screwdriver, installs in 20–30 minutes 🛡️ Fixes Common Issues – Restores heating, prevents shutdowns, resolves overheating problems 📐 Product Specification Part Number: 280148 Component Type: Dryer Thermostat Set (high-limit thermostat + thermal cutoff fuse) L146-44C, 295-111F with 50 Ohm thermistor. Material: High-temperature resistant metal and thermal fuse components Mounting: Direct replacement kit with standard connections Operating Conditions: Suitable for residential dryer heating systems Compliance: OEM-equivalent safety and performance standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before servicing your dryer to avoid electrical shock. Steps: Unplug dryer and locate the heating element housing. Remove screws securing access panel and locate old thermostat and fuse. Disconnect wire terminals from defective components. Replace with new thermostat and cutoff fuse from this kit. Reattach wires, secure components, and reinstall access panel. Restore power and test dryer operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix your dryer’s heating issues quickly — Add to Cart Now for a reliable, budget-friendly repair kit.

Read more less

DC47-00018A CM Dryer Thermostat L260-50F. 125/250V. 25A. 1/4" spade terminals. Used on DC97-14486A elements. Replaces Parts Numbers: DC47-00018A, 1122485, AP4201898, PS4205217. Description: This High Limit Thermostat is a replacement part for specific Samsung dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO LA1053 Dryer Thermostat Kit – Replaces LA-1053 – Compatible with Whirlpool, Maytag, Admiral, and Amana Dryers Product Description Restore proper dryer temperature control with the XPARTCO LA1053 Dryer Thermostat Kit. This Dryer Thermostat Kit is a replacement part for specific Maytag, Whirlpool dryer models. This kit includes a high-limit thermostat and a thermal fuse, both of which are crucial for regulating the dryer’s temperature. The high-limit thermostat prevents the dryer from overheating, while the thermal fuse will cut off power if a critical temperature is exceeded, ensuring safety. The kit includes a high-limit thermostat (53-0771) and two thermal fuses. 53-1096 (blue dot for Gas) 53-1182 (Red dot for Electric) Replaces Part Numbers LA-1053, 3344, 53-0143, 53-0170, 53-0261, 53-1133, 53-1526, AH2162282, EA2162282, ERLA1053, ET403, ET405, K35-601, LA-1053VP, LA1053, SET405, TJ90SET405, 531526, 531182, 531133, 530261, LA1053, 530143, WP53-1182, 53-1182, 53-0143, 53-1096 , L248-80F, PD00002446, EAP2162282, AP4242472, PS2162282, WP53-0771, 53-0771, 1422, 53-0306, 53-1037, 53-1459, ER53-0771, SET176, TJSET176, AP6009638, PS11742806, WP53-1096, 53-1096, 4434853, AP6009640, PS11742808.  Compatibility This replacement thermostat kit fits select Whirlpool, Maytag, Admiral, and Amana dryers. Example compatible models include (but are not limited to): Maytag DE303, Whirlpool LDE8824ACE, and Amana LEA30AW. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Compatibility – Compatible with Whirlpool, Maytag, Admiral, and Amana dryers 🔥 Complete Kit – Includes cycling thermostat, high-limit thermostat, and thermal fuse. Dryer thermal fuse and high limit thermostat kit for both gas and electric models. If the dryer does not heat then the thermal fuse may have blown and will need to be replaced.  💰 Cost-Effective Repair – Replaces multiple components in one package 🛠️ Easy to Install – Direct-fit parts require only basic tools 🛡️ Fixes Common Issues – Resolves dryers not heating, overheating, or shutting off early 📐 Product Specification Part Number: LA1053 Component Type: Dryer Thermostat and Thermal Fuse Kit Material: Heat-resistant metal with high-quality electrical connectors Mounting: Direct-fit replacement on heater housing and blower housing Operating Conditions: Designed for residential electric dryers Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Unplug the dryer and remove the rear access panel. Locate the thermostat and thermal fuse on the heater housing. Remove screws securing the old components and disconnect wires. Install the new thermostats and fuse from the XPARTCO LA1053 kit. Reconnect wiring, reinstall the back panel, and restore power. Run a test cycle to confirm proper heating and temperature control. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dryer running safely and efficiently again — Add to Cart Now for a reliable, budget-friendly repair kit!

Read more less

197XP Dryer Thermostat Kit – Replaces 279816, WP3977767, W10900067 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Restore safe and efficient drying performance with the 197XP Dryer Thermostat Kit. This high-quality aftermarket replacement includes both a high-limit thermostat and a thermal cut-off fuse to regulate dryer temperature and prevent overheating. A failed thermostat or cut-off can cause long dry times, no-heat conditions, or overheating. Installing this complete kit ensures dependable temperature control and long-lasting dryer operation. Replaces Part Numbers 279816, 2651, 279816VP, 3399848, 3977393, AH334299, AP3094244, EA334299, PS334299, WP3977767, 3977767, 3399693, 898078, AP6009043, ER3977767, PS11742185, SET185, TJ90SET185, WP3977767VP, W10900067, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement thermostat kit fits select Whirlpool, Kenmore, Maytag, Amana, Roper, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.87562602, and Amana NED4655EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM temperature ratings and safety standards 🔥 Dual-Protection Design – Includes thermal cut-off fuse and high-limit thermostat for overheat prevention 💰 Affordable Alternative – Provides OEM-level performance at a lower cost 🛠️ Easy DIY Installation – Pre-terminated connectors and hardware for quick repair 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or short-cycling problems 📐 Product Specification Part Number: 197XP Temperature Ratings: 309* degree F Thermal Fuse with L250-80* degree F Limit Thermostat. High Limit Thermostat and Thermal Fuse for the Heater.      No need to splice any wires, no re wiring needed.  Component Type: Dryer Thermal Cut-Off & High-Limit Thermostat Kit Includes: Thermal cut-off fuse, high-limit thermostat, mounting hardware, and wire connectors Material: Metal thermostat housing with heat-resistant wiring Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the back panel of the dryer. Locate the heater housing and identify the existing thermostat and cut-off fuse. Remove wires and mounting screws from old components. Install the new 197XP thermostat kit in the same positions. Reconnect wires, reassemble the panel, and restore power. Run a drying cycle to confirm proper operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dryer and restore heat safely — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC47-00016A Dryer Thermostat - Compatible with select Samsung, Whirlpool, Maytag, Kenmore Dryers Product Description Protect your dryer from overheating with the replacement DC47-00016A Dryer Thermostat. This thermal cut-off thermostat is designed for select Samsung, Whirlpool and Kenmore dryers, shutting off the motor when the dryer overheats to prevent damage or hazards. It addresses issues like no heat, insufficient heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermal cut-off thermostat with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: DC47-00016A, L0016A, AP4201894, PS4205213, AP6008681, EAP4205213, EAP11741821, PD00005341, PD00003747, PS11741821, 35001087, WP35001087. Compatibility: Compatible with models including but not limited to: Samsung: DV203AGS, DV203AGW/XAA-0000, DV206AES, DV209AEW/XAA-0000, DV210AEW, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, and LG dryers. 🔥 Specifications: replacement thermal cut-off thermostat, opens at 260°F, two 1/4" male spade terminals. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, insufficient heat, failure to start, or premature shutoff. Product Specification Part Number: XPARTCO DC47-00016A Component Type: Thermal cut-off thermostat Material: Metal and plastic Electrical Specs: 125/250V, 25A, 85°C - 35°C, 185°F. Mounting: Two 1/4" male spade terminals, mounts on blower housing Operating Conditions: Suitable for high-temperature dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and efficient today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 3977394 Dryer Thermal Cut-Off Kit –  Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable XPARTCO 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F, EXPTC352 Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less