Dryer Fuses, Thermostats, Heaters & Igniters

XPARTCO 137032600 Dryer Thermal Fuse – Compatible with Frigidaire, Electrolux, and Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 137032600 Dryer Thermal Fuse. This high-quality aftermarket replacement acts as a safety device that shuts off power to the heating element if the dryer overheats. A blown fuse can cause the dryer to stop heating or fail to start. Replacing it with this reliable and affordable XPARTCO fuse ensures safe operation and restores your dryer’s performance. Replaces Part Numbers 137032600, 137060800, 1483164, 7137032600, AH2349395, EA2349395, PD00000890, EAP2349395, AP4368739, PS2349395. Compatibility This replacement thermal fuse fits select Frigidaire, Electrolux, and Kenmore dryers. Example compatible models include (but are not limited to): Frigidaire AEQ6000ES0, Electrolux EIED55HIW0, and Kenmore 417.88042700. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance for Frigidaire and Electrolux dryers 🔥 Safety Protection – Prevents overheating by cutting off power to the heating element 💰 Cost-Effective Fix – Affordable alternative to expensive OEM replacements 🛠️ Easy Installation – Direct-fit design for simple DIY replacement 🛡️ Fixes Common Issues – Restores heat function and resolves dryer not starting or heating problems 📐 Product Specification Part Number: 137032600 Component Type: Dryer Thermal Fuse Material: Heat-resistant plastic and metal housing Mounting: Direct-fit installation on heater housing Operating Conditions: Designed for residential electric dryers Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and move dryer away from the wall. Remove the rear access panel to locate the thermal fuse. Disconnect wires and remove screws securing the old fuse. Install the new XPARTCO 137032600 fuse and reconnect wires. Reattach the back panel, restore power, and test heating function. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🧰 Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dryer and restore performance — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5301EL1001J Dryer Genuine Heating Element Fits Specific LG Dryer Models. 240V, 5400W complete assembly with housing and thermostats Replaces Part Numbers: 5301EL1001J, 5301EL1001A, 1377645, AEG72910307, AH3527791, AP4439759, EA3527791, PS3527791, 5301EL1001H, 1377645, 5301EL1001E, 5301EL1001G, 5301EL1001S, 5301EL1001U, 5301EL1001W, AH3527790, AP5072170, EA3527790, PS3527790, AEG72910301, AP5669354, AEG72910309, AP7211081. Description:  This Heater Assembly is a Genuine OEM part for specific LG dryer models. This component is responsible for generating the heat required to dry clothes effectively. It consists of a heating element and necessary components that work together to maintain the desired drying temperature, ensuring clothes come out dry and ready to wear.  Causes of a bad heater assembly can include wear and tear from regular use, overheating, electrical issues, or damage to the heating element itself. A malfunctioning heater assembly can lead to inefficient drying or no heat at all. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.go

Read more less

XPARTCO 3977767 Dryer Hi Limit Thermostat 250 -80F Limit Thermostat. Fits specific Maytag, Kenmore, Whirlpool dryer models. Replaces Part Number: WP3977767, 3977767, 3399693, ER3977767, SET185, TJ90SET185, WP3977767VP, AP6009043, PS11742185. Description: This Hi-Limit Thermostat is a replacement part for specific Maytag, Kenmore, Whirlpool dryer models. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 279769 Dryer Thermostat Kit The XPARTCO 279769 is an aftermarket replacement thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279769, 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. As an aftermarket replacement, the 279769 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO 279769 Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match Whirlpool's factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) OEM Part Number 279769 Condition Aftermarket Replacement Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 279769 high-limit thermostat and thermal cut-off fuse kit used in compatible Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5300622032 Genuine OEM Dryer Heater Restring - Compatible with Frigidaire, Electrolux, Kenmore Product Description Restore optimal drying performance with the 5300622032 Genuine OEM Dryer Heater Restring. This authentic Frigidaire-manufactured heating element restring coil is designed for select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers, generating heat to efficiently dry clothes. Built for durability and precise fit, it addresses issues like no heat or insufficient heat. Note: Includes one heating element restring coil with 1/4" terminals (4600 watts, 240 volts). Does not include heater housing insulators (131472100) or terminal block (3202786). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: 5300622032, 08015672, 3202787, 3281114, AH451031, DE335, EA451031, NQ00622032, Q000622032, Q622032, TJ90DE335, WQ622032, PD00000126, EAP451031, AP2135127, PS451031. Compatibility: Compatible with models including but not limited to: Frigidaire: FDE646GES0, FDE747GES0, FDE847GES0, F31C336ES0, F31C436ES0 Gibson: GSE746RFS0, GSE746RFS1, GDE336RES1, GDE546RES0 Tappan: TDE336RED0, TDE546REW0 Kenmore, Electrolux, Kelvinator, White Westinghouse: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers. 🔧 Specifications: Genuine OEM heating element restring coil, 1/4" terminals, 4600 watts, 240 volts. 💪 Reliable Performance: Authentic Frigidaire part ensures efficient heat generation and long-lasting operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–45 minutes. 🛡️ Effective Fixes: Resolves no heat or insufficient heat in the dryer. Product Specification Part Number: 5300622032 Component Type: Dryer heating element restring coil Material: Metal alloy coil Electrical Rating: 4600 watts, 240 volts Mounting: Fits within existing heater housing, screw-mounted Operating Conditions: Suitable for household dryer environments Compliance: UL listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse Replaces WP8573713 The XPARTCO 8573713 is an aftermarket replacement thermal cut-off fuse for Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. This fuse is mounted on top of the burner funnel, directly under the drum, and it's a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant temperatures near the burner climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power. That's why a blown fuse produces such a specific symptom: the dryer won't heat, even though the drum may still tumble and the rest of the dryer seems to run normally. Because this fuse sits on the burner funnel underneath the drum rather than on the more accessible blower housing, replacing it is a more involved repair than a typical thermal fuse swap — the drum has to come out of the cabinet to reach it. Unlike a resettable thermostat, this fuse cannot be reset once it blows; it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat near the burner is exactly what this fuse is designed to react to. It directly replaces WP8573713, AP6013467, and PS11746693. Quick Answer The XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse fixes Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers that won't heat, even if the drum still tumbles normally. Mounted on the burner funnel under the drum. Replaces WP8573713, AP6013467, PS11746693. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer runs and tumbles but produces no heat Dryer that stopped heating suddenly, especially after running unusually hot Drying times that have gotten noticeably longer or clothes coming out damp Repeated blown fuses on a dryer with a known venting or airflow restriction Dryer that recently smelled like burning or overheating before losing heat Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers: WP8573713, 1180872, 8573713, AP3866211, EAP990558, PS990558, AWP49233, PD00006618 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal cut-off fuse is compatible with select Whirlpool gas dryers, and also fits select Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers built on the Whirlpool platform, including model numbers such as WGD8500SR0, and Kenmore 11070372710 and 11071112020. Note: This fuse is specific to gas dryers, mounted on the burner funnel. It is not the same fuse used on electric dryer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats Mounted on top of the burner funnel, directly under the drum Resolves "runs but won't heat," "drying takes too long," and "clothes coming out damp" symptoms caused by a blown fuse Replaces WP8573713, AP6013467, and PS11746693 Compatible with Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8573713 OEM Part Number WP8573713 Part Type Gas Dryer Thermal Cut-Off Fuse Condition Aftermarket Replacement Application Gas Dryers Location Top of the burner funnel, under the drum Resettable No — one-time use, must be replaced once blown Material Plastic housing Dimensions Approx. 1"H x 1"W Repair Difficulty Moderate to Hard — drum removal required for access Quantity 1 thermal cut-off fuse Compatible Brands Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, Sears Canada Installation Notes ⚠️ Gas Safety — Shut Off The Gas Supply Before Starting This fuse sits directly on the burner funnel, close to the gas burner assembly. Before beginning, close the gas shutoff valve behind the dryer in addition to unplugging the dryer or shutting off its circuit breaker. If at any point you smell gas, stop immediately, leave the area, and do not operate any switches — contact your gas utility or a qualified technician. Do not attempt this repair if you are not comfortable working safely around a gas appliance's burner assembly; a qualified technician can complete it instead. ⚠️ Drum Removal Required — Inspect And Clean The Venting Before Reassembling Wear work gloves. This repair requires removing the drum from the dryer cabinet to access the burner funnel, so budget more time and disassembly than a typical thermal fuse swap. Remove the top and front panels according to your model's service diagram, disconnect the drive belt from the idler pulley, and lift the drum out of the cabinet to expose the burner funnel underneath. Photograph the wiring before disconnecting the old fuse's connectors. Test the old fuse for continuity with a multimeter to confirm it's actually blown (no continuity) rather than assuming, and test the new fuse to confirm it's good out of the box. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new 8573713 fuse on the burner funnel in the same mounting position, reconnect the wiring, and reassemble the drum, belt, and panels in reverse order. Restore the gas supply and power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer tumbles fine but there's no heat. Is this the right part? Yes, this is the classic symptom of a blown gas dryer thermal cut-off fuse. Because this fuse only interrupts the heating circuit and not the drive motor, the drum can continue tumbling completely normally while the dryer produces no heat at all. If you've confirmed the burner isn't igniting and the fuse tests as an open circuit, this is very likely the fix. Why does this repair require removing the drum? My other dryer's fuse didn't need that. This particular fuse is mounted on the burner funnel underneath the drum rather than on the blower housing at the back of the cabinet, which is where many thermal fuses on other platforms are located. Reaching the burner funnel requires taking the drum out of the cabinet, which is why this repair involves more disassembly than some other thermal fuse replacements. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and mounting configuration of the original WP8573713 thermal cut-off fuse used in compatible Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 35001092 Dryer Thermostat – Replaces WP35001092 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain proper dryer temperature and consistent drying results with the XPARTCO 35001092 Dryer Thermostat. This High Limit Thermostat is a replacement part for specific dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards. Replaces Part Numbers WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.  Compatibility This replacement dryer thermostat fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature cycling performance 🌡️ Accurate Heat Regulation – Maintains safe, consistent drying temperatures 🔧 Reliable Thermal Control – Helps prevent overheating and heat loss 💰 Cost-Effective Repair – Quality alternative to OEM thermostats 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses 📐 Product Specification Part Number: 35001092 Component Type: Dryer Operating Thermostat Application: Heater or exhaust temperature regulation Material: Heat-resistant metal thermostat housing Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermostat on the heater housing or exhaust duct. Disconnect wiring and remove the old thermostat. Install the new XPARTCO 35001092 thermostat. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less