Dryer Fuses, Thermostats, Heaters & Igniters

Genuine OEM Dryer Part W11683629 Dryer Genuine OEM Thermistor A manufacturer-approved temperature-sensing component designed to help the dryer control system regulate heat and drying performance. Product Description The W11683629 Dryer Genuine OEM Thermistor monitors air temperature inside the dryer and sends temperature information to the electronic control system. The control uses this signal to cycle the heat source and maintain the correct operating temperature during the drying cycle. This is a Genuine OEM replacement part manufactured to the original equipment specifications for fit, electrical response, and dependable operation. Replacing a failed thermistor can help restore accurate temperature control, normal cycle times, and consistent drying results. Quick Answer W11683629 is a Genuine OEM dryer thermistor. It senses dryer air temperature and communicates with the control board so the appliance can regulate heating. Replace it when testing or diagnosis confirms an open, shorted, damaged, or inaccurate temperature sensor. Common Problems This Part Fixes Dryer overheats or runs hotter than normal Clothes remain damp after a complete cycle Drying cycles take too long Heat cycles on and off incorrectly Dryer stops before clothes are dry Temperature-sensor or heating-related error codes Replaces Part Number The product title identifies the following part number: W11683629, W11452857, AP7216892, AWP1400864, PS17216463.  No additional replacement or cross-reference number was included in the supplied product title. Compatibility Designed for select dryer models that specify Genuine OEM part number W11683629. Appliance parts can look similar while using different resistance ranges, connectors, mounting positions, or control logic. Always verify the complete dryer model number and the required part number before ordering. The model-number label is commonly located around the door opening, on the cabinet frame, or on the rear identification plate. Key Features Genuine OEM manufacturer-approved component Monitors dryer operating temperature Sends temperature feedback to the control system Helps regulate heating and cycle performance Built to original fit and electrical specifications Direct replacement when W11683629 is specified Product Specifications Part Number W11683629 Part Type Dryer Thermistor / Temperature Sensor Condition New Quality Genuine OEM Application Clothes Dryer Primary Function Measures air temperature for the dryer control system Package Quantity 1 Thermistor Troubleshooting Guide Disconnect the dryer from electrical power before opening or servicing the cabinet. Inspect the exhaust vent, lint path, and blower area. Restricted airflow can produce symptoms similar to a failed thermistor. Inspect the thermistor body, terminals, connector, and wire harness for damage, corrosion, loose connections, or heat discoloration. Disconnect the thermistor and test resistance with a multimeter. Compare the reading with the dryer service information for the measured temperature. Warm or cool the sensor carefully. Resistance should change smoothly as temperature changes; an open circuit, short circuit, or unstable reading can indicate failure. Check the heater circuit, thermal devices, moisture-sensing system, and control board when the thermistor tests within specification. Safety: Do not bypass a thermistor or protective temperature device. Installation and diagnosis should be performed by a qualified person when you are not comfortable servicing electrical appliances. When Should You Replace This Part? The thermistor is open, shorted, or outside the specified resistance range The sensor reading does not change correctly with temperature The housing or connector is cracked, burned, or physically damaged A service diagnostic identifies W11683629 as the failed component Airflow and related heating components have been checked and the thermistor fails testing Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your dryer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM Fast U.S. Shipping Compatibility Support Secure Checkout  

Read more less

17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools. Quick Answer The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models. Common Problems This Part Fixes Dryer overheating — thermistor not accurately reporting rising temperature to the control board Dryer not heating at all — thermistor circuit open or shorted Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle Dryer taking much longer than normal to complete a cycle Not-heating fault code displayed on models with digital control panels Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading Dryer cycling heat on and off erratically Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 17438200000404, WF-123X2060,  AP7157538, PS18188581 Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including: Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13 Criterion — CDE41N1AW (electric), CDG41N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models Replaces WF-123X2060 Installs in 20–30 minutes with basic hand tools Product Specifications Part Number 17438200000404 Part Type Dryer Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at Room Temp Approximately 10,000 – 12,000 ohms (~70°F) Location Blower housing/exhaust duct or drum cavity, depending on model Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing). Frequently Asked Questions How do I test if the temperature sensor (thermistor) has failed? Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine. My Midea dryer has more than one temperature sensor — how do I know which one to replace? Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor. What is the difference between 17438200000404 and WF-123X2060? These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part. Does this sensor fit my Insignia or Criterion dryer? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

(8 Pack) 3977394 Dryer Thermal Cut-Off Kit – Replaces 3977394 – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

WP8544772 Dryer Genuine OEM Heating Element Replaces part Numbers: WP8544772, 8544772, 1180055, AP6013116, PS11746338. Restore your dryer’s heating performance with the WP8544772 Heating Element. This Genuine OEM part is designed to provide consistent, efficient heat for drying your clothes quickly and evenly. Key Features: ✅ Genuine OEM Part – built for performance and durability 🔁 Replaces: WP8544772, 8544772, 1180055, AP6013116, PS11746338. 🔥 Produces the necessary heat for drying cycles 🛠️ Fits select Whirlpool, Kenmore, Maytag, Amana, and Crosley dryers 🧰 Easy to install – plug-and-play direct replacement ⚠️ Unplug dryer before servicing. Need help confirming fit? We’re here to assist! 📦 Part Number: WP8544772💯 30-Day Money Back Guarantee

Read more less