Welcome to Parts-O-Matic - Home page

XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570 This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features 2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 2 kits per order (2 door catches and 2 strikes in total) Product Specifications Part Number EXP570 (2 Pack) OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike per Kit Quantity 2 Kits (2 Door Catches & 2 Strikes) Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO (2 Pack) EXP571 Dryer Door Catch The XPARTCO (2 Pack) EXP571 is a two-pack of aftermarket replacement door catches for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 2 door catches. Quick Answer The XPARTCO (2 Pack) EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 2 catches per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 2 door catches per order Product Specifications Part Number EXP571 (2 Pack) OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 2 Door Catches Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 2 door catches. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

197XP Dryer Thermostat Kit – Replaces 279816, WP3977767, W10900067 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Restore safe and efficient drying performance with the 197XP Dryer Thermostat Kit. This high-quality aftermarket replacement includes both a high-limit thermostat and a thermal cut-off fuse to regulate dryer temperature and prevent overheating. A failed thermostat or cut-off can cause long dry times, no-heat conditions, or overheating. Installing this complete kit ensures dependable temperature control and long-lasting dryer operation. Replaces Part Numbers 279816, 2651, 279816VP, 3399848, 3977393, AH334299, AP3094244, EA334299, PS334299, WP3977767, 3977767, 3399693, 898078, AP6009043, ER3977767, PS11742185, SET185, TJ90SET185, WP3977767VP, W10900067, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement thermostat kit fits select Whirlpool, Kenmore, Maytag, Amana, Roper, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.87562602, and Amana NED4655EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM temperature ratings and safety standards 🔥 Dual-Protection Design – Includes thermal cut-off fuse and high-limit thermostat for overheat prevention 💰 Affordable Alternative – Provides OEM-level performance at a lower cost 🛠️ Easy DIY Installation – Pre-terminated connectors and hardware for quick repair 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or short-cycling problems 📐 Product Specification Part Number: 197XP Temperature Ratings: 309* degree F Thermal Fuse with L250-80* degree F Limit Thermostat. High Limit Thermostat and Thermal Fuse for the Heater.      No need to splice any wires, no re wiring needed.  Component Type: Dryer Thermal Cut-Off & High-Limit Thermostat Kit Includes: Thermal cut-off fuse, high-limit thermostat, mounting hardware, and wire connectors Material: Metal thermostat housing with heat-resistant wiring Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the back panel of the dryer. Locate the heater housing and identify the existing thermostat and cut-off fuse. Remove wires and mounting screws from old components. Install the new 197XP thermostat kit in the same positions. Reconnect wires, reassemble the panel, and restore power. Run a drying cycle to confirm proper operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dryer and restore heat safely — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406107 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

2 Pack - XPARTCO 303373K Dryer Drum Roller Replaces 12001541, WP6-3129480 The XPARTCO 303373K is an aftermarket replacement drum roller support wheel kit for Maytag dryers, and also fits select Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral models. This roller supports the rear of the dryer drum and allows it to spin smoothly against the rear bulkhead throughout the drying cycle, working together with the front drum supports to keep everything rotating evenly. This kit includes 2 roller, 2 shaft (axle), 2 fiber washer, 2 nut, and 2 C-clip/retainer clip. The roller measures approximately 3" in diameter and 1-1/8" wide, fits a 1/2" shaft, and does not require lubrication. Finished in white or black, made of rubber, plastic, and metal. Over time, the roller's bearing wears out or the wheel develops flat spots from age and use. Symptoms of worn rollers include the dryer being noisy, failing to tumble, leaving marks on clothes, or failing to start. It directly replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, and 312948. Quick Answer The XPARTCO 303373K Dryer Drum Roller fixes Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers that are noisy, won't tumble, leave marks on clothes, or won't start. Single roller and shaft, 3" diameter, 1-1/8" wide, fits 1/2" shaft, no lubrication needed. Replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, 312948. For even wear, it's recommended to replace both rear drum rollers at the same time — you'll need two of this kit if your dryer uses two rear rollers. Common Problems This Kit Fixes Dryer noisy during operation Drum won't tumble Marks left on clothes Dryer won't start Squeaking noise during the drying cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum roller kit directly replaces the following OEM and cross-reference part numbers: 12001541, 12001541VP, 3-3373, 303373, 400518, W10116741, DE693, W10116741, Y303373, AH1570070, EA1570070, K35-248, AP4008534, AWP38865, EAP1570070, PD00004911, PS1570070, WP6-3129480, 6-3129480, 1480353, 3-12948, 312948, W10912638, WP6-3129480VP, Y312948, AP6009858, AWP48110, EAP2347258, PD00002609, PS11743031 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller kit is compatible with select Maytag dryers, and also fits select Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers built on the Maytag platform, including model numbers such as: MDE5500AYW, MDE2600AYW, MDE4000AYW, MDE6800AYW, MDE7400AYW, MDE7500AYW, MDE8600AYW, MDE9606AYW LDE4916ACE, LDE4916ACM, LDE4916ADE, LDE5916ACE, LDE5916ACM, LDE5916ADE LDE7600ACL, LDE8426GGE, LDE8624ACE, LDE9206ACE, LDE9206ACM, LDE9206ADE, LDE9334ACE, LDE9806GGE, LDE512 LDG4916AAE, LDG4916AAM, LDG5916AAE, LDG5916AAM LSE7806ACE, MDG9520BWW, DE303, DG7500 Note: Always verify your full model number before ordering, since Maytag uses several different drum roller designs across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum roller support wheel kit — single roller and shaft Resolves "noisy," "won't tumble," "marks on clothes," and "won't start" symptoms caused by worn rollers Kit includes 2 roller, 2 shaft, 2 fiber washer, 2 nut, and 2 C-clip 3" diameter, 1-1/8" wide, fits a 1/2" shaft Self-lubricating bearing — no lubrication required White or black finish, rubber/plastic/metal construction Direct drop-in replacement matching the original mounting Replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, and 312948 Compatible with Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 303373K OEM Part Number 12001541 Part Type Dryer Drum Roller Support Wheel Kit Condition Aftermarket Replacement Kit Contents 1x Roller, 1x Shaft, 1x Fiber Washer, 1x Nut, 1x C-Clip Roller Diameter 3" Roller Width 1-1/8" Shaft Fit 1/2" Lubrication Not required — self-lubricating bearing Color White / Black Material Rubber / Plastic / Metal Repair Difficulty Easy to Moderate Quantity 2 drum roller (single kit) Compatible Brands Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Install The Snap Ring Before Assembling The Roller Onto The Shaft Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the dryer, then remove the drum to access the rear drum roller(s). Remove the old roller by taking off the retainer clip, sliding the roller off its shaft, and removing the shaft itself if it's also being replaced. One customer found it much easier to install the C-clip/snap ring onto the new shaft before assembling the rest of the roller, rather than after. Once assembled this way, you're only dealing with tightening a nut at the back, which can be finger-tightened and then given about a half turn with a 1/2" wrench — useful since one side of the mounting area can be tight to access. Install the new roller, shaft, fiber washer, and nut in the same position, following this assembly order. If your dryer uses two rear rollers and you've ordered a second kit to replace both, repeat this process for the other side. Reinstall the drum, making sure it seats correctly on the new roller(s). While the dryer is fully open, this is also a good opportunity to clean out any accumulated lint from inside the cabinet, since lint buildup here is a genuine fire hazard that isn't addressed by simply cleaning the lint trap. Reassemble the back panel. Restore power and run a test cycle to confirm quiet, smooth tumbling with no marks transferring to clothes. Tools needed: nut driver, 1/2" wrench, work gloves. Frequently Asked Questions My dryer squeaks. Is this the part I need? Yes, squeaking is one of the most common symptoms of worn drum rollers. As the roller's bearing wears down, it can no longer support the drum's rotation smoothly, producing a squeaking or squealing noise that typically gets more noticeable over time. Should I replace both rollers, or just the one that's obviously worn? It's recommended to replace both rear drum support rollers at the same time for even wear, even if only one appears visibly worse than the other. This kit includes a single roller and shaft, so if your dryer uses two rear rollers, you'll want to order two of this kit to replace both together. Do I need to lubricate these rollers? No, these rollers use a self-lubricating bearing and do not require any additional lubrication during installation or afterward. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag OEM part, but is manufactured to match the diameter, width, and shaft fit of the original 12001541 drum roller kit used in compatible Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279973 Dryer Genuine OEM Thermostat Kit Replaces: 279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, AH334387, AP3094323, EA334387, PS334387.  Description: This Thermal Cut-Off Kit is a Genuine OEM part for select Kenmore, Whirlpool dryer models, responsible for protecting the dryer from overheating by interrupting the power flow to the heating element if the dryer air temperature reaches a dangerously high level.  

Read more less