XPARTCO 4681EA2001T Washer Drain Pump Motor The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase. This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more. Common Problems This Part Fixes OE error code displayed — washer cannot drain within the allotted time Washer not draining — standing water remaining in the drum after a cycle Loud humming or buzzing during the drain cycle — motor running but impeller not turning Grinding or rattling noise during draining — physical damage to pump components Washer stopping mid-cycle due to a drain fault Washer draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. 4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T. Compatibility This drain pump motor is compatible with select front-load washers from the following brands: LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series Kenmore / Sears front-load washers (select LG-built models, including 796-series) Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models Spin speed: 1,100–1,200 RPM for powerful, efficient drainage Includes pump impeller and removable filter housing with sealing ring Removable filter housing allows easy cleaning without full pump disassembly Sealing ring reduces vibration and noise during operation Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles Motor assembly only — installs into existing pump housing, no housing replacement needed Resolves OE error code on compatible LG and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 4681EA2001T Also Replaces 4681EA2001N (updated current replacement) Part Type Washer Drain Pump Motor Assembly Condition Aftermarket Replacement Application LG and Kenmore Front-Load Washers Voltage 120V – 127V AC Frequency 60 Hz Wattage 85W Amperage 1.4A Flow Rate 45 liters per minute Spin Speed 1,100 – 1,200 RPM Material Metal / ABS Plastic Includes Motor assembly, impeller, removable filter housing, sealing ring Note Motor assembly only — existing pump housing is reused Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan. Frequently Asked Questions What is the difference between 4681EA2001T and 4681EA2001N? These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order. What does the OE error code mean on an LG washer? OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement. Does this include the pump housing? No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced. Should I check the drain filter before replacing the pump motor? Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10810403 (OE) Washer Lid Switch Assembly – Compatible with Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana Washers Product Description Keep your washer running safely and reliably with the XPARTCO W10810403 Washer Lid Switch Assembly. This replacement part ensures the washer only operates when the lid is securely closed, preventing unsafe operation. A faulty lid switch can cause your washer to not start, stop mid-cycle, or fail to drain. Replacing it with this high-quality part restores dependable performance. What is OE ?:  “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. They offer identical fit and function to OEM (Original Equipment Manufacturer) components but are typically sold under independent brands like XPARTCO for better affordability. Replaces Part Numbers W10810403, 4283179, W10648012, W10787878, W10810403VP, PD00028176, EAP11722981, AP5984435, PS11722981. Compatibility This washer lid switch assembly is compatible with select Whirlpool, Kenmore, Maytag, Crosley, Roper, and Amana top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW4800BQ1, Kenmore 110.20222511, and Maytag MVWC415EW1. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana top-load washers 🔒 Safe Operation – Ensures washer won’t run with lid open 💰 Cost-Effective Alternative – OEM-equivalent performance at a lower price 🛠️ Easy Installation – Only requires a Phillips screwdriver, installs in 10–20 minutes 🛡️ Fixes Common Issues – Resolves washers not starting, stopping mid-cycle, or failing to drain 📐 Product Specification Part Number: W10810403 Component Type: Washer Lid Switch Assembly Material: High-durability plastic + electrical connectors Mounting: Direct replacement, top panel mount Operating Conditions: Designed for standard residential washer use Compliance: OEM-equivalent quality standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver ⚠️ Safety First: Always unplug the washer before starting repairs to avoid electrical shock. Steps: Unplug washer and locate lid switch under the top panel. Remove screws securing the control panel and release clips. Disconnect the wire harness from the old switch. Remove the old switch and install the new one in its place. Reconnect wiring, secure panel, and test the washer. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your washer’s performance today — Add to Cart Now for a safe, budget-friendly fix!

Read more less

XPARTCO W11220230 Washer Water Inlet Valve The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.. Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors. Quick Answer The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation. Common Problems This Part Fixes Washer not filling with water Slow water fill during cycles Water continuously flowing into washer Incorrect water temperature Washer stopping due to fill errors Leaking or stuck inlet valve Replaces Part Numbers This water inlet valve replaces the following part numbers: W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select washers from the following brands: Whirlpool washers Maytag washers Amana washers Kenmore / Sears washers (select models) Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Three coil hot and cold water valve. OEM-equivalent fit, performance, and durability Restores proper water fill levels and cycle operation Durable construction resists mineral buildup and wear Prevents leaks and overfilling issues Direct replacement for W11220230 valve assembly Product Specifications Part Number W11220230 Part Type three coil hot and cold water inlet valve. Application Top Load / Front Load Washers Condition Aftermarket Replacement Function Controls Water Flow Compatible Brands Whirlpool, Maytag, Amana, Kenmore Installation Notes ⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation. Frequently Asked Questions What does a washer water inlet valve do? It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill. Will this fix a washer that won’t fill? Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6501EA1001R Washer Water Level Pressure Switch The XPARTCO 6501EA1001R is an aftermarket replacement water level pressure switch compatible with select LG and Kenmore top-load and front-load washers — including the WT1, WT4, WT5, WT7 series and WM series. The pressure switch is a sealed sensor connected to the tub by a flexible air hose. As water fills the tub, air pressure inside the hose increases proportionally, and the switch translates that pressure into an electrical signal that tells the control board the current water level. The control board uses this signal to know when to stop filling, when to add more water, and to confirm the tub has drained before advancing to the next cycle phase. When the pressure switch fails, the washer may not fill with enough water, may overfill and leak (error code UE), may stop filling altogether, or may display error codes E4, E7, PE, F04, or F05 depending on the model. This switch has a body diameter of approximately 2.3"–2.4", body height of approximately 2.05", and includes an air pressure hose approximately 29" long. It directly replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, 5210FA3427J, AP5204365, AH3529177, EA3529177, EAP3529177, and PS3529177. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6501EA1001R Washer Water Level Pressure Switch fixes LG and Kenmore washers displaying error codes E4, E7, PE, UE (overflow), F04, or F05, not filling with enough water, overfilling and leaking, or not filling at all. Body diameter ~2.3"–2.4", height ~2.05", 29" air pressure hose. Replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, AP5204365, PS3529177. Compatible with LG WT1xxx–WT7xxx, WM series, and Kenmore (LG-built) washers. Common Problems This Part Fixes Error codes E4, E7, or PE displayed — water level pressure switch fault Error code UE (overflow) — switch not signaling the control board to stop filling Error codes F04 or F05 displayed on certain models — water level sensing fault Washer not filling with enough water for the selected cycle Washer overfilling — water level rising past the normal fill point and leaking from the tub Washer not filling with water at all Washer stopping mid-cycle due to a water level fault Inconsistent or inaccurate water level across different load sizes Replaces Part Numbers This pressure switch directly replaces the following OEM and cross-reference part numbers: 6501EA1001R, EBF62754506, 2651052, 5210FA3427J, 6501EA1001C, PD00022947, EAP3529177, AH3529177, EA3529177, AP5204365, ALG1185730, OEM15613104, PS3529177. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This pressure switch is compatible with select LG and Kenmore washers from the following series: LG top-load washers — WT1 series (WT1101CW, WT1201CW, WT1201CV, WT1501CW, WT1701CW, WT1801HVA, WT1801HWA and related models) LG top-load washers — WT4 series (WT4870CW, WT4970CW and related models) LG top-load washers — WT5 series (WT5001CW, WT5070CW, WT5101HV, WT5101HW, WT5270CW, WT5680HVA, WT5680HWA and related models) LG top-load washers — WT7 series (WT7200CW, WT7200CV, WT7300CW, WT7305CV, WT7600HWA, WT7600HKA and related models) LG front-load washers — WM series (WM2032HS and related models) LG washers — T1309ADFH, T1309ADFH6, T1309ADFN, WF-T8501 series Kenmore / Sears washers — 79629272000, 79629278000, 79631512210, 79631512211, 79631463410, 79629002010, 79629478000, 79631412310 and related models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Senses water level in the tub via air pressure changes in a connected hose — signals the control board to start, stop, or adjust water fill Resolves error codes E4, E7, PE, UE, F04, and F05 caused by pressure switch failure on compatible models Body diameter approximately 2.3"–2.4", body height approximately 2.05" Includes air pressure hose approximately 29" long Prevents overfilling and underfilling — restores accurate, energy-efficient water level control Replaces 6501EA1001C, 6501EA1001D, 6501EN1001R, EBF62754506, EBR78940615, 2651052, AP5204365, and PS3529177 Compatible with LG WT1xxx, WT4xxx, WT5xxx, WT7xxx, WM series, and Kenmore LG-built washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6501EA1001R Also Replaces 6501EA1001C, 6501EA1001D (prior versions) Part Type Washer Water Level Pressure Switch Condition Aftermarket Replacement Application LG and Kenmore Top-Load and Front-Load Washers Body Diameter Approximately 2.3 – 2.4 inches Body Height Approximately 2.05 inches Hose Length Approximately 29 inches Error Codes Resolved E4, E7, PE, UE, F04, F05 Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. On most LG top-load models, the pressure switch is located behind the control panel or console at the top of the washer. Slide and lift the top panel or remove the control panel screws to access the switch — refer to your model's service instructions if uncertain. Locate the switch and its connected air pressure hose, which routes down to a fitting on the tub. Photograph the wire harness connections before disconnecting. Disconnect the wire harness connector from the switch. Carefully disconnect the air pressure hose from the old switch (avoid kinking or puncturing the hose). Unclip or unscrew the old switch from its mounting bracket. Install the new 6501EA1001R switch into the mounting slot, ensuring it locks securely with the retaining tabs. Reconnect the air pressure hose and the wire harness. Reinstall the panel, restore power, and run a fill cycle to confirm normal water level control and check that no error codes appear. Tools needed: Phillips screwdriver, putty knife (for some models). Frequently Asked Questions What do error codes E4, E7, and PE mean on LG washers? E4 and E7 on LG front-load and top-load washers, and PE on certain LG top-load models, all indicate a water level sensing fault detected by the pressure switch. These codes appear when the control board receives an inconsistent, absent, or out-of-range pressure signal from the switch — preventing the washer from accurately determining how much water is in the tub. Replacing the pressure switch resolves these codes when the switch itself has failed; if the air hose is pinched, disconnected, or has a small leak, that should also be checked and corrected before assuming the switch needs replacement. What does error code UE mean and how does the pressure switch relate to it? UE typically indicates an unbalanced load error on LG washers, but in some cases it can also appear in connection with overfilling caused by a pressure switch that is not correctly signaling the control board to stop adding water. If you are experiencing overflow along with a UE code, and you've confirmed the load is balanced and not the unbalance cause, a failed pressure switch allowing continuous fill is a possible explanation and replacing the switch can resolve the overfill behavior. What is the difference between 6501EA1001R and 6501EA1001C? These are the same pressure switch across different production revisions. 6501EA1001C was an earlier version, and 6501EA1001R is the current updated part number. The 6501EA1001D and 6501EN1001R are also cross-references for this same switch. All are fully interchangeable — if your washer's parts diagram shows any of these numbers, this replacement covers all of them. My washer isn't filling with enough water — could it be the pressure switch instead of the inlet valve? Yes — insufficient water fill is commonly assumed to be a water inlet valve problem, but the pressure switch is just as likely a cause. If the inlet valve is delivering water normally but the pressure switch is misreporting the water level as already full, the control board will stop the fill cycle prematurely. Before replacing the inlet valve, check the pressure switch's air hose for kinks, pinches, or disconnection, and consider testing or replacing the switch if the hose is intact and undamaged. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the dimensions and air-pressure sensing performance of the original 6501EA1001R water level pressure switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11210459 Genuine OEM Washer Water Inlet Valve - Compatible with Whirlpool, Kenmore, Maytag, Amana Product Description Keep your washer running smoothly with the W11210459 Genuine OEM Washer Water Inlet Valve. This Whirlpool-manufactured valve assembly is designed as a replacement for select Whirlpool, Kenmore, Maytag, Amana, and other compatible washing machines. It controls the flow of hot and cold water into the washer during wash and rinse cycles, ensuring proper filling and efficient operation. This part addresses issues like leaking water, slow or no water fill, inconsistent water temperature, or overflow, often caused by a faulty or clogged valve. Note: Includes (1) water inlet valve assembly with two solenoids (hoses and clamps not included). Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, PD00042885, EAP12349267, AP6329217, PS12349267.  Compatibility: Compatible with select washer models, including but not limited to: Whirlpool: WTW5000DW1, WTW4816FW2, WTW4616FW2, WTW4815EW1, WTW4816FW1 Kenmore: 110.25132411, 110.22352511 Maytag: MVWC565FW0, MVWC415EW1 Amana: NTW4516FW3 Crosley, Inglis, Roper: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washing machines. 🔧 Specifications: Genuine OEM Whirlpool water inlet valve with two solenoids, 110-120V, 60Hz, standard 3/4" hose fitting inlet. 💪 Reliable Performance: Controls hot and cold water flow for consistent wash and rinse cycles. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves leaking, slow or no fill, inconsistent water temperature, or overflow issues. Product Specification Part Number: W11210459 Component Type: Washer water inlet valve assembly Material: Plastic and metal Electrical Specs: 110-120V, 60Hz, two solenoids, standard 3/4" hose fitting inlet, two water outlets. Compliance: UL-listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO W11165546 Washer Water Inlet Valve The XPARTCO W11165546 is an aftermarket replacement washer water inlet valve assembly compatible with Maytag Bravos XL, Whirlpool Cabrio, Kenmore 700-series, and related Whirlpool-platform HE top-load washers. This 4-solenoid assembly controls the flow of hot and cold water from the household supply lines into the washer tub and dispenser compartments. It includes an integrated thermistor on the center outlet that monitors incoming water temperature and communicates it to the control board so the washer can achieve the correct wash temperature. When the valve fails — or when a single solenoid coil burns out — the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. Rated 120V, 60Hz, with 2 inlet ports and 3 outlet ports, this assembly measures 5-3/8"L x 4-1/4"W x 3"H. The valve body may be blue or green in color depending on production run — both are functionally identical. It is compatible with 1/2" ID supply hoses. It directly replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, WV5546, 33090105, 4545980, AP6284346, EAP12348013, PD00037668, and PS12348013. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO W11165546 Washer Water Inlet Valve fixes Maytag Bravos XL and Whirlpool Cabrio/WTW HE top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. 4-solenoid valve with thermistor. 120V/60Hz. 2 inlet / 3 outlet ports. 5-3/8"L x 4-1/4"W x 3"H. Compatible with 1/2" ID supply hoses. Replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, 33090105, 4545980, AP6284346, PS12348013. Common Problems This Part Fixes Washer not filling with water — error code F8E1, LF, or LO FL displayed Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection — thermistor failed Water dripping into the tub between cycles — valve not closing completely Water leaking from the back of the washer near the valve Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: W10839828, 33090105, 4545980, W10599423, W10758828, W11096267, W11165546VP, AP6284346, AWP43457, EAP12348013, PD00037668, PS12348013. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select HE top-load washers from the following brands and series: Maytag top-load washers — Bravos XL series (MVWB765FW0, MVWB765FW1, MVWB765FW2, MVWB765FW3, MVWB765FC1, MVWB765FC2, MVWB766FW0, MVWB766FW1, MVWB835DW1, MVWB835DW2, MVWB835DW3, MVWB835DW4, MVWB855DC2, MVWB855DC3, MVWB865GC0, MVWB865GW0, MVW6230HW2, MVW7230HW0, MVW7232HW0 and related models) Whirlpool top-load washers — Cabrio / WTW series (WTW7500GC0, WTW7500GW0, WTW8500DC2, WTW8500DC4, WTW8500DC5, WTW8500DR4, WTW8500DR5, WTW8500DW4, WTW8500DW5, WTW8700EC1, 7MWTW8500EC2 and related models) Kenmore / Sears top-load washers — 700 series (11028132410, 11028132411, 11028132412, 11028132413, 11028133410, 11028133411, 11029132411, 11029133410 and related models) Crosley top-load washers (select models) Note: The valve body color may be blue or green depending on production run — both are functionally identical. This valve is for HE top-load washers only. Always verify your model number before ordering. Key Features 4-solenoid valve assembly — controls hot water, cold water, and additional dispenser/recirculation ports to fill the tub with the correct temperature water for each cycle Integrated thermistor on center outlet — monitors incoming water temperature and communicates with the control board to achieve the correct wash temperature Resolves F8E1, LF, and LO FL error codes on compatible Maytag and Whirlpool HE top-load washers Rated 120V, 60Hz — correct electrical specifications for compatible models Dimensions: 5-3/8"L x 4-1/4"W x 3"H 2 inlet ports, 3 outlet ports — compatible with 1/2" ID supply hoses Valve body color (blue or green) varies by production run — functionally identical Replaces W10599423, W10758828, W10839828, W11096267, and W11165546VP Compatible with Maytag Bravos XL MVWB series, Whirlpool WTW7xxx/WTW8xxx, Kenmore 700 series, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number W11165546 Part Type Washer Water Inlet Valve Assembly (4-Solenoid with Thermistor) Condition Aftermarket Replacement Application HE Top-Load Washers — Bravos XL, Cabrio, WTW series Solenoids 4-coil (hot, cold, and additional ports) Thermistor Integrated on center outlet — monitors water temperature Voltage 120V AC Frequency 60 Hz Dimensions 5-3/8"L x 4-1/4"W x 3"H Inlet Ports 2 (hot and cold) Outlet Ports 3 Supply Hose ID 1/2 inch Color White / Blue or Green (production run dependent — functionally identical) Error Codes Resolved F8E1, LF, LO FL Compatible Brands Maytag, Whirlpool, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose routing before disconnecting. Disconnect the two external supply hoses from the valve inlet ports using pliers to loosen any stuck connections. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from all solenoid coils and the thermistor. Unscrew the mounting hardware and remove the old valve. Install the new W11165546 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the same positions as documented. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers, channel-lock pliers for stubborn hose connections. Frequently Asked Questions What do error codes F8E1, LF, and LO FL mean on Maytag and Whirlpool washers? F8E1 (also displayed as LF or LO FL on some models) indicates a long fill fault — the washer was unable to fill to the required water level within the expected time. The most common causes are a failed water inlet valve (solenoid coil burned out or valve seat clogged), low household water pressure, or kinked supply hoses. Before replacing the valve, confirm both supply valves are fully open, the supply hoses are not kinked, and household water pressure is adequate. If all supply conditions are good and the error persists, the water inlet valve is the most likely cause. What is the difference between W11165546 and W11096267? These are the same water inlet valve assembly. W11096267 was an earlier version, and W11165546 is the current updated part number. The W10599423 and W10758828 are also cross-references to earlier versions of this same valve. The W11165546VP is the Whirlpool factory-packaged version. All of these are covered by this aftermarket replacement. Why does this valve have 4 solenoids? Modern HE top-load washers like the Maytag Bravos XL and Whirlpool Cabrio use multiple water paths for different wash functions — hot water inlet, cold water inlet, a bleach dispenser port, and a fabric softener/recirculation port. Each path is controlled by its own independent solenoid coil on the same valve assembly. This allows the control board to independently open any combination of ports needed for a given cycle phase. When any single solenoid coil fails, only the function controlled by that coil is affected — which is why the washer might fill normally with cold water but not hot, or fail to activate only one dispenser. Does the valve color (blue vs green) matter? No — the blue and green valve body colors are simply the result of different production runs at the factory. Both colors are the same part number (W11165546) with identical electrical specifications, port configuration, thermistor, and dimensions. Either color will function correctly in your washer. There is no functional difference between the two. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with 4 solenoid coils and an integrated thermistor to match the electrical specifications and port configuration of the original W11165546 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11481722 Washer Genuine OEM Shift Actuator Replaces Part Numbers: W11481722, W10597177, WPW10597177, W11237117, W11398781, AP6990751, PS16221077.  Shift Actuator, Mode shift actuator with 6 pin wire connection  Description: This Actuator is a Genuine OEM part for select Whirlpool washing machine models. This part shifts the washer between different cycles and functions, such as agitation and spinning. It ensures that the washing machine transitions smoothly and operates effectively throughout each cycle.  

Read more less

XPARTCO WH12X955 Washer Lid Switch for GE & Hotpoint Washer/Dryer Combos – Reliable OEM Replacement 🔧 Product Description:Ensure safe and efficient operation for your GE or Hotpoint washer/dryer combo with the XPARTCO WH12X955 Washer Lid Switch, a premium, OEM-compatible replacement. This essential safety switch detects lid closure, preventing the unit from agitating or spinning when open, protecting your appliance and household. Built from high-quality plastic with a secure wiring harness, it provides durable performance and precise activation. Ideal for DIY repairs, this switch resolves issues like non-spinning cycles or error codes in 20–40 minutes. Key Features: 🔧 Broad Compatibility: Fits GE, Hotpoint, and select washer/dryer combo models (see below). 💪 Durable Build: High-impact plastic housing with reliable wiring for long-term use. ⚙️ Simple Installation: Replace with basic tools in minutes – no professional needed. 🔒 Safety-Focused Design: Ensures accurate lid detection to prevent unsafe operation. 🛡️ 30 Days Hassle-Free Return: Shop with confidence with our risk-free return policy. Compatibility:Fits numerous GE and Hotpoint washer/dryer combo models, including: WSM2420D0WW, WSM2420D0CC WSM2420D1WW, WSM2420D2WW WSM2420D3WW, WSM2420SCZAA WSM2420TAACC, WSM2480D1WW WSM2480TBAAA Replaces Part Numbers: WH12X955, 278666, AH270219, EA270219, PD00030733, EAP270219, PS270219, AP2045786, WH12X0955, EXPWH12X955Verify fit with your model’s manual or serial number. Specifications: Material: High-Impact Plastic with Wiring Harness Part Number: WH12X955 (XPARTCO Brand) Installation Instructions: Unplug the washer/dryer combo and turn off the water supply. Remove the top panel by unscrewing rear bolts and sliding it back. Locate the old lid switch near the lid hinge, disconnect the wiring harness, and remove mounting screws. Install the XPARTCO switch, reconnect the harness, and secure in place. Reassemble the panel, plug in, and test a cycle.Shop Now for free, fast shipping and a 30-day hassle-free return policy! Customer Reviews:⭐⭐⭐⭐⭐ “Fixed my GE combo unit's spin problem in 25 minutes – works like new!” – Karen L.⭐⭐⭐⭐⭐ “Perfect fit for my Hotpoint WSM2420, easy install and reliable!” – Steve R. Add to Cart and restore safe, efficient washing today! FAQs:Q: Will this fit my GE washer/dryer combo?A: The XPARTCO WH12X955 fits most GE and Hotpoint combo models. Check your model number or contact support to confirm.Q: Is this an OEM part?A: It’s a premium aftermarket part engineered to meet or exceed OEM standards.Q: How do I install it?A: Use basic tools for a quick swap. Follow our digital guide or YouTube tutorial for step-by-step help.

Read more less

DC97-15459G Washer Water Valve 120V, 60Hz, five coil linear valve. Fits Specific Samsung Washer Models. Replaces Part Numbers:DC97-15459G, AP5623056, PS4220861. Description: The Water Valve Assembly is a replacement part for specific Samsung washing machines. It controls the flow of hot and cold water into the washer during the different cycles, ensuring the proper mix and temperature for effective cleaning.  The water valve assembly can fail due to various reasons such as mineral deposits from hard water clogging the valve, electrical issues, or general wear and tear over time. Exposure to high water pressure or impurities in the water supply can also lead to malfunction.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10913953 Washer Shift Actuator The XPARTCO W10913953 is an aftermarket replacement washer shift actuator assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper top-load washers with VM (variable motor) transmissions — including Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos series. The shift actuator is a small synchronous gearmotor assembly located beneath the washer tub that controls how the transmission shifts between agitation mode and spin mode during the wash cycle. It moves the arm on the cam ring assembly to engage the basket (for spinning) or disengage it and engage only the agitator or wash plate (for agitation). The shift actuator also contains an internal tachometer that continuously reports the basket's rotational speed to the control board. When the shift actuator fails — most commonly due to a stripped or broken gear inside the gearmotor — the washer may not agitate, not spin, get stuck in one phase of the cycle, display error codes F7E1 or F7E5, or produce a loud grinding or clicking noise as the gears fail. This 6-pin plug assembly is rated 120V, 60Hz, 4W with a synchronous motor running at 3 RPM clockwise rotation. It measures 4-1/4"L x 2-3/4"W x 1-7/8"H and directly replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, 50SM21-1-221B, AP6037270, and PS11769864. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10913953 Washer Shift Actuator fixes Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos top-load washers that won't agitate, won't spin, display error codes F7E1 or F7E5, or make grinding/clicking noises when trying to shift cycles. 6-pin plug, 120V/60Hz/4W synchronous motor, 3 RPM CW, 4-1/4"L x 2-3/4"W x 1-7/8"H. Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, AP6037270, PS11769864. Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper VM-transmission top-load washers. Common Problems This Part Fixes Washer not agitating — basket fills with water but agitator or wash plate does not move Washer not spinning — cycle advances to spin but basket does not rotate Washer getting stuck in one phase — completing wash or fill but not advancing to spin Clothes soaking wet after a full cycle — washer is not reaching high-speed spin Error codes F7E1 or F7E5 displayed — motor shift or basket speed sensing fault Loud grinding, clicking, or buzzing noise during cycle transitions between agitate and spin Washer pumping normally but basket not spinning after draining Replaces Part Numbers This shift actuator directly replaces the following OEM and cross-reference part numbers: W10913953, W10815026, 4455082, 49TYZ-E120A1, 50SM21-1-221B, KT-155867_rev011, EAP11769864, AP6037270, AWP42172, PD00032232, PS11769864. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select top-load washers with VM transmissions from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW5000, WTW4816, WTW4850, WTW4915, WTW4950, WTW4955 and related models) Maytag top-load washers — Centennial series (MVWC215, MVWC415, MVWC416, MVWC465, MVWC555, MVWC565 and related models) Maytag top-load washers — Bravos series (MVWX655 and related models) Kenmore / Sears top-load washers (select Whirlpool-built models) Amana top-load washers — NTW series (NTW4516, NTW4655 and related models) Crosley top-load washers (select models) Inglis top-load washers (select models) Roper top-load washers (select models) Note: The W10913953 is for VM (variable motor) transmission top-load washers. It is not compatible with older Whirlpool top-load washers using a different transmission type. Always verify your model number before ordering. The shift actuator works in conjunction with the pulley clutch kit (W10721967 / W10006384) — if the actuator is good but the issue persists, the clutch kit should also be inspected. Key Features Controls transmission shifting between agitation mode and spin mode during the wash cycle Moves the cam ring arm to engage the basket for spinning, or disengage it to allow only the agitator/wash plate to move Integrated tachometer — continuously reports basket rotational speed to the control board for cycle management Synchronous gearmotor — 120V, 60Hz, 4W, 3 RPM clockwise rotation 6-pin plug connector — direct plug-in installation on compatible models Dimensions: 4-1/4"L x 2-3/4"W x 1-7/8"H Resolves F7E1 and F7E5 error codes on compatible Whirlpool and Maytag top-load washers Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, and AP6037270 Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos, Amana NTW, and Kenmore VM-transmission top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10913953 Also Replaces W10815026, W10597177 (prior versions) Part Type Washer Shift Actuator Assembly (Mode Shift Actuator) Condition Aftermarket Replacement Application Top-Load Washers with VM Transmission (Cabrio, Centennial, Bravos) Motor Type Synchronous gearmotor Voltage 120V AC Frequency 60 Hz Wattage 4W Speed 3 RPM, clockwise rotation Connector 6-pin plug Dimensions 4-1/4"L x 2-3/4"W x 1-7/8"H Includes Integrated tachometer for basket speed sensing Error Codes Resolved F7E1, F7E5 Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. The shift actuator is located beneath the washer tub on the drive shaft assembly. To access it, remove the washer cabinet by unscrewing the top panel and releasing the front panel, or lay the washer on its back if your model requires it. The shift actuator is mounted to the bottom of the drive shaft assembly with mounting screws and connects to the washer's control harness via a 6-pin plug. Photograph the wiring before disconnecting. Remove the mounting screws, disconnect the 6-pin harness, and slide the old actuator off the shaft. Install the new W10913953 actuator in the same position and orientation, secure the mounting screws, and reconnect the 6-pin harness. Reassemble the cabinet, restore power and water, and run a test cycle through both agitation and spin to confirm normal operation. Note: if grinding noise continues after replacing the actuator, inspect the pulley clutch kit (W10721967 / W10006384) for wear. Tools needed: Phillips screwdriver, 1/4" nut driver, Torx screwdriver (T20 on some models). Frequently Asked Questions What does the shift actuator do in a top-load washer? The shift actuator is a small synchronous gearmotor that controls the transmission shifting in Whirlpool Cabrio, Maytag Centennial, and Bravos-style VM-transmission top-load washers. During a wash cycle, the control board signals the actuator to move the cam ring arm — this engages or disengages the drive connection between the motor and the basket. When the cam moves one way, only the agitator or wash plate moves (agitation mode). When it moves the other way, the basket engages and spins at high speed (spin mode). The actuator also contains a tachometer that tells the control board how fast the basket is rotating, which the board uses to manage spin speed and detect imbalance. What are error codes F7E1 and F7E5? On compatible Whirlpool Cabrio and Maytag Centennial/Bravos top-load washers, F7E1 indicates a motor shift error — the actuator failed to complete the shift between agitate and spin mode within the expected time. F7E5 indicates a basket speed sensing fault — the tachometer inside the actuator is not providing a valid speed signal to the control board. Both codes are commonly caused by a failed shift actuator, though a failed drive motor, clutch assembly, or control board can also produce these codes. Replacing the shift actuator resolves both error codes in most cases. Should I also check the pulley clutch kit? Yes — if the shift actuator is replaced but the grinding noise persists, or if the washer still does not agitate or spin properly after the new actuator is installed, inspect the pulley clutch kit (W10721967 / W10006384). The clutch kit is a separate assembly that works in conjunction with the shift actuator to engage the drum. A worn or stripped clutch can produce the same symptoms as a failed actuator and is a common companion failure. Since the washer is already disassembled to replace the actuator, it is a good opportunity to inspect the clutch for wear. What is the difference between W10913953 and W10815026? The W10815026 was an earlier version of this shift actuator, and the W10913953 is the updated current replacement. Both are the same functional component — Whirlpool updated the part number during a production revision. The W10597177 and WPW10597177 are also cross-references for this same actuator. If your washer's parts diagram shows any of these older numbers, the W10913953 is the correct current replacement to order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a synchronous gearmotor and ABS housing to match the electrical specifications and dimensions of the original W10913953 shift actuator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X29528 Washer Door Lock The XPARTCO WH01X29528 is an aftermarket replacement door lock assembly compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Monogram front-load washing machines — as well as select GE UltraFast 2-in-1 combo washer/dryer units. The door lock is a safety mechanism mounted at the front of the washer where the door closes — it automatically engages when the door is shut, securing it closed for the entire wash and spin cycle so water and detergent can't spill out and cause injury. It also signals the control board that the door is safely locked, which is what allows the washer to start filling and running. When the door lock fails, the washer typically won't start, won't lock the door, stops mid-cycle, or throws a door-related error code. Rated 120 VAC, 60Hz, 16A. Failure usually comes from physical damage or normal wear over time. As a direct replacement for the GE WH01X29528, it also replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 (additional production markings: ITW 12070-71, V13305, 0024000128GE). Installation is straightforward with no wiring modifications — remove the old lock and install the new one, typically in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO WH01X29528 Washer Door Lock fixes GE, GE Profile, Café, and Haier front-load washers (and GE UltraFast 2-in-1 combo units) where the door won't lock or unlock, the washer won't start, the washer stops mid-cycle, the door feels loose or won't seal, or a door-latch error code appears. 120 VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, PS12749276, PD00060769, 4958749. Compatible with GE GFW510, GFW550, GFW650, GFW850, PFW870, PFW950, PFQ97 series front-load washers. No wiring modifications — installs in 10–15 minutes. Common Problems This Part Fixes Washer door won't lock at the start of the cycle Washer won't start — control board not detecting a locked door Washer door won't unlock at the end of the cycle Washer stops mid-cycle due to a door lock fault Door-latch related error code displayed on the control panel Door feels loose or doesn't seal properly Excessive noise and shaking while the washer is running (related to a door not securing properly) Intermittent locking — washer sometimes starts, sometimes doesn't Door lock assembly visibly broken, cracked, or with a failed latch Burning/electrical smell or humming from the door lock area (failed lock solenoid) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AGE26402, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, OEM20955948, V13305, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock assembly is compatible with select front-load washing machines and combo washer/dryer units from the following brands: GE front-load washers — GFW510 series (GFW510SCN0WW–SCN5WW, GFW510SCV0WW) GE front-load washers — GFW550 series (GFW550SPN0DG–SPN3DG, GFW550SPR0RS/SPR3RS/SPR4RS/SPR5RS, GFW550SSN0WW–SSN5WW) GE front-load washers — GFW650 series (GFW650SPN0SN–SPN4SN, GFW650SSN0WW–SSN4WW) GE front-load washers — GFW655 series (GFW655SPV0DS, GFW655SSV0WW) GE front-load washers — GFW850 series (GFW850SPN0DG–SPN5RS all DG/RS variants, GFW850SSN0WW–SSN5WW) GE Profile front-load washers — PFW870 series (PFW870SPV0RS, PFW870SSV0WW), PFW950 series (PFW950SPT0DS/SPT1DS/SPT2DS) GE Profile combo units — PFQ97HSPV0DS (UltraFast 2-in-1 combo washer/dryer) GE Café, Haier, Hotpoint, RCA, Monogram — select front-load models using the same door lock Sears Kenmore and Crosley — select GE-built front-load models Always verify your appliance model number before ordering. The WH01X29528 fits the specific models listed — please double-check your model number. Contact our support team if you're unsure. Key Features Door lock and switch assembly — locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Prevents the door from being opened mid-cycle, keeping water and detergent safely contained Resolves "won't lock," "won't unlock," "won't start," "stops mid-cycle," and door-latch error codes when caused by a failed lock Rated 120 VAC, 60Hz, 16A — correct electrical specifications for compatible GE front-load washers Integrates with the washer's main control board, door switch, and load detection system Durable, moisture-resistant materials resist deformation, wear, and short circuits for long service life No wiring modifications required — direct-fit replacement using the original connector Replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 Compatible with GE GFW510/GFW550/GFW650/GFW850, PFW870/PFW950, and PFQ97 series front-load washers and UltraFast combo units, plus select Café, Haier, Hotpoint, RCA, Monogram, Kenmore, and Crosley GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPWH01X29528 Part Type Washer Door Lock and Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers & Combo Washer/Dryer Units (GE platform) Voltage 120 VAC Frequency 60 Hz Amperage 16A Additional Production Markings ITW 12070-71, V13305, 0024000128GE Function Locks door during wash/spin; signals control board door is secure Location Front of washer at the door opening Compatible Brands GE, GE Profile, Café, Haier, Hotpoint, RCA, Monogram, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, you may need to access the manual release. Peel back the rubber door boot/gasket from the front panel edge near the lock to expose the door lock assembly — on some models this requires releasing the spring-loaded wire clamp that secures the boot with needle-nose pliers. Photograph the wire harness connection before disconnecting anything. Remove the mounting screws holding the door lock assembly to the front panel. Reach in and pull the assembly out through the door opening far enough to access the wire connector. Disconnect the wire harness plug from the old assembly (no wiring modifications are needed — it's a direct plug connection). Snap the new WH01X29528 assembly onto the wire harness plug until it clicks firmly, position it in the front panel opening, and secure it with the mounting screws. Press the rubber door boot back into its groove and reinstall the spring-loaded wire clamp if applicable. Restore power and test by closing the door and starting a cycle — confirm the door locks, the washer runs, and the door unlocks at the end. Tools needed: Phillips screwdriver, needle-nose pliers, work gloves. Frequently Asked Questions My GE washer won't start and shows a door error — is this the part? Very likely, yes. GE front-load washers won't start unless the control board receives confirmation from the door lock that the door is closed and locked — it's a safety interlock. When the door lock fails, the washer either won't lock the door, won't start, or displays a door-related message on the panel. If your door appears to close normally but the washer won't begin the cycle (or stops shortly after starting), the door lock is the most common cause. Replacing the WH01X29528 typically resolves it. If you've already replaced the door lock and the problem persists, the issue may be the main control board instead. I replaced the door lock and it worked briefly, then failed again — what's wrong? If a new door lock works for a short time (seconds to minutes) and then the washer goes back to showing a door error, the problem may not be the lock itself but the main control board that powers and monitors it. A control board with a failing door-lock circuit can damage or fail to properly drive the lock, causing repeated symptoms even after replacing the lock. Some customers report an electrical smell or humming from the lock in these cases. If you've replaced the door lock (especially more than once) and the door error returns, the main control board is the next component to investigate. Contact our support team with your model number for the correct control board part. Does this fit the GE UltraFast 2-in-1 combo washer/dryer? Yes — the WH01X29528 is used on select GE UltraFast 2-in-1 combo washer/dryer units (such as the PFQ97HSPV0DS) in addition to standalone GE front-load washers. The combo units use the same door lock design as the front-load washers in the GFW/PFW families. As always, confirm your specific model number against the compatibility list before ordering, since GE uses different door locks across different washer generations. How do I open the door if it's stuck locked and the washer won't run? If the door is stuck in the locked position because of a failed lock, first make sure there's no water in the drum (run or complete a drain cycle if possible). Then unplug the washer and wait a few minutes — some GE models release the lock after power is removed. If it's still stuck, most front-load washers have a manual release mechanism accessible from behind the lower kick panel at the front of the machine — a tab or cord you pull to manually disengage the lock. Consult your model's manual for the manual release location. Once the door is open, you can proceed with replacing the lock. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable, moisture-resistant materials to match the electrical specifications (120 VAC, 60Hz, 16A), connector configuration, mounting, and door-locking function of the original WH01X29528 door lock used in compatible GE, GE Profile, Café, Haier, and related front-load washers and combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less