XPARTCO 5304511335 Washer Water Level Pressure Switch – Compatible with Frigidaire & Electrolux Washers
Product Description
Restore accurate water level control and proper washer operation with the XPARTCO 5304511335 Washer Water Level Pressure Switch. It is responsible for detecting the water level inside the washer tub and ensuring accurate water level control during the wash cycle. It detects the pressure changes caused by the water level, allowing the washer to adjust the water intake accordingly.
A faulty pressure switch can cause overfilling, under-filling, or cycles not advancing properly. Replacing it with this reliable XPARTCO component helps ensure correct water levels and consistent wash performance.
XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function.
Replaces Part Numbers
5304511335, 4584277, EAP12176459, AFR17584, OEM18784872, PD00046588, AP6261621, PS12176459.
Compatibility
This replacement washer water level pressure switch fits select Frigidaire, Electrolux, Gibson, Crosley, and Kenmore (Frigidaire-manufactured) washers.
Common compatible models include (but are not limited to):
Frigidaire FFTW4120SW1, FFTW4120SW0, FFTW4120SW, FFTW4120SW0
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and pressure sensing performance
💧 Accurate Water Level Detection – Ensures proper fill and cycle control
⚙️ Fixes Common Issues – Resolves overfill, underfill, and cycle errors
🧩 Direct-Fit Design – Installs easily with existing hose and wiring
💰 Cost-Effective Repair – Affordable alternative to OEM pressure switches
⚠️ Symptoms
If your washer is experiencing any of the following issues, this part may need replacement:
💧 Washer overfilling or underfilling
⚠️ Incorrect water levels during cycles
🔄 Cycle not advancing properly
🛑 Washer stops mid-cycle
🚫 No water or continuous filling
Replacing this pressure switch can restore proper water level control and washer performance.
📐 Product Specification
Part Number: 5304511335
Component Type: Washer Water Level Pressure Switch
Function: Detects water level and signals control board
Connection Type: Air hose + electrical connector
Application: Washer water level sensing system
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver
⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock.
Basic Steps:
Disconnect washer power.
Access the control panel or top panel.
Locate the pressure switch and disconnect the air hose and wiring.
Remove mounting screws and remove the old switch.
Install the new XPARTCO 5304511335 pressure switch.
Reconnect hose and wiring, reassemble, and restore power.
Run a test cycle to verify correct water levels.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore accurate water level control and reliable washer performance — Add to Cart Now for a dependable repair!
WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve
The WPW10327249 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers, mounted on the right-hand side of the dishwasher's interior behind the front kick plate. This valve regulates the flow of water into the appliance during each cycle, opening to admit water from the household supply and closing once the correct amount has entered, which is essential to proper filling and efficient operation.
Over time, mineral or sediment buildup inside the valve body, or general electrical wear in the solenoid, can cause the valve to fail. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, water filling inconsistently or too slowly, leaking, or overfilling. It directly replaces AP6019618, W10316814, W10327249, W11130743, WPW10327249VP, 3015511, PS11752927, and W11669945.
Quick Answer
The WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers that won't fill with water, fill inconsistently, leak, or overfill. Located on the right-hand side of the dishwasher interior. Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter (W10685193), since it's in the same area and easy to inspect at the same time.
Common Problems This Part Fixes
Dishwasher not filling with water at all
Water filling inconsistently or too slowly
Dishwasher leaking near the valve area
Dishwasher overfilling
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher water valve directly replaces the following OEM and cross-reference part numbers:
WPW10327249, W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, and Maytag dishwashers built on the Whirlpool platform, including model numbers such as WDT750SAHZ, WDTA50SAHZ, WDT710PAYM, MDB4949SDM, and MDB4949SHZ.
Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary in size or shape between models. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates water flow into the dishwasher during each fill cycle
Resolves "won't fill," "fills inconsistently," "leaking," and "overfilling" symptoms caused by valve failure
Direct drop-in replacement — matches the original mounting and hose connections
Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927
Compatible with Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Novice-friendly repair with basic hand tools
Product Specifications
Part Number
WPW10327249
Part Type
Dishwasher Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Location
Right-hand side of the dishwasher interior, behind the front kick plate
Color
Blue
Water Line Connections
Two 3/8" lines
Repair Difficulty
Medium — basic appliance repair skills
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Maytag
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply at the shutoff valve located behind the dishwasher before beginning. Wear work gloves. Remove the bottom front kick plate by pulling outward on the two clips located at either side of the bottom panel. Locate the water inlet valve on the right-hand side of the dishwasher interior. Disconnect the two 3/8" water lines from the old valve. Unscrew the mounting screws holding the valve in place, and carefully pull the old valve away from the dishwasher. Insert the new WPW10327249 into the dishwasher, making sure it's securely positioned, and secure it with the mounting screws. Reconnect both water lines to the new valve. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Turn the water supply back on and plug the dishwasher back into the power source. Run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: multi-screwdriver, standard pliers, adjustable wrench, work gloves.
Frequently Asked Questions
My dishwasher isn't filling with water at all. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
Should I check or replace the water supply adapter while I have the dishwasher open?
It's a reasonable idea, since the water supply adapter is a related component located in the same general area and is easy to inspect while you already have access. It doesn't need to be replaced automatically, but checking its condition at the same time can save you from needing to open the dishwasher back up again soon after if it's also showing wear.
My dishwasher is leaking near the valve. Could hard water be a factor?
Yes, mineral and sediment buildup from hard water is a common contributor to valve failure over time, since it interferes with the valve's ability to seal and shut off properly. Using a dishwasher cleaner periodically to help reduce limescale buildup can support the longevity of the new valve, though it isn't a substitute for replacing a valve that has already failed.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob
The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings.
Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required.
Quick Answer
The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required.
Common Problems This Part Fixes
Selector knob cracked, broken, or split from age and repeated use
Knob loose and slipping on the control shaft — no longer changes settings when turned
Knob has stripped or damaged internal grip and won't stay coupled to the shaft
Knob missing entirely from the control panel
Knob damaged from impact — dropped or bumped
Knob discolored, faded, or worn from years of daily handling
Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly
Water or detergent damage to the knob material
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This cycle selector knob directly replaces the following OEM and cross-reference part numbers:
WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This selector knob is compatible with select washers and dryers from the following brands:
GE washers — GTW500ASNWS and related top-load models
GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models
GE Profile and GE Café washers and dryers (select models)
GE Monogram washers and dryers (select models)
Hotpoint washers and dryers (select models)
RCA washers and dryers (select GE-built models)
Haier washers and dryers (select models using GE-platform controls)
Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure.
Key Features
Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle
Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required
Heat-resistant plastic construction — designed for years of daily use without warping or cracking
Clean white and chrome finish complements GE appliance styling
Ergonomic shape for comfortable grip and precise cycle selection
Restores full cycle control when the original knob has cracked, stripped, or gone missing
Replaces WH01X24378, AP5986397, 4396548, and PS11726904
Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers
Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately)
Aftermarket replacement built to OEM-equivalent quality standards
Quick replacement — installs in under 1 minute
Product Specifications
Part Number
XPWH01X24378
Part Type
Washer/Dryer Cycle Selector Knob (Options Knob)
Condition
Aftermarket Replacement
Application
Washers and Dryers (GE platform)
Knob Size
Smaller cycle/options knob (NOT the larger main timer knob)
Color
White / Chrome
Material
Heat-resistant plastic
Installation
Snap-on — no tools required
Larger Timer Knob
Different part — PS11736611 (sold separately)
Compatible Brands
GE, Hotpoint, RCA, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional).
Frequently Asked Questions
Is this the smaller or larger knob on my GE washer?
The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable.
How do I remove the old knob if it's cracked or spinning without coming off?
If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too.
Do I really not need any tools for this?
Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in.
The knob installs fine but my washer still doesn't change settings — what next?
If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WH49X27616 Washer Genuine OEM Tub Cover
Cross Reference Information
Part Number WH49X27616, WH44X10286, 4591241, AP6331330, PS12343566.
Description
Note: Newly designed cover includes 4 new rod and spring assemblies. The tub dampening straps and clips are no longer used.
WD19X25278 Dishwasher Diverter Assembly
The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning.
The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK.
Quick Answer
The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first.
Common Problems This Part Fixes
Water pooling or leaking underneath the dishwasher
Poor washing performance from one or both spray arms
Unusual noise during the wash cycle
Water not properly directed to the correct spray arm
Inconsistent cleaning results between the upper and lower racks
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers:
WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB.
Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement diverter assembly — controls water flow to the spray arms
Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms
Valve and float assembly engineered to optimize water flow while minimizing noise
Direct drop-in replacement matching the original mounting and connections
Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK
Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
DIY-friendly repair
Product Specifications
Part Number
WD19X25278
OEM Part Number
WD19X25278
Part Type
Dishwasher Diverter Valve Assembly
Condition
Aftermarket Replacement
Function
Controls water flow direction to the upper and lower spray arms
Design
Valve and float assembly
Repair Difficulty
Easy to Moderate — DIY-friendly
Quantity
1 diverter assembly
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
I'm seeing water pooling under my dishwasher. Is this the part I need?
Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it.
Any tips to avoid damaging the new part during installation?
Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this.
Is this a difficult repair?
No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WD01X29878 Dishwasher Door Latch – Compatible with GE Dishwashers
Product Description
Restore secure door closing and proper dishwasher operation with the XPARTCO WD01X29878 Dishwasher Door Latch. This high-quality aftermarket replacement ensures the dishwasher door locks firmly during wash cycles and signals the control board that it is safe to operate. A faulty door latch can cause the dishwasher not to start, stop mid-cycle, or display door-related error codes. Replacing it with this reliable XPARTCO latch helps restore safe and dependable washing performance.
XPARTCO offers cost-effective aftermarket appliance parts engineered to match original fit and function.
Replaces Part Numbers
WD01X29878, WD01X27701, 265D1214G004, EG-380944, PD00072017, FIX16659468, 4979622, AP7176296, PS16659468.
Compatibility
This replacement dishwasher door latch fits select GE dishwashers.
Common compatible models include (but are not limited to):
GE GDT655SSJSS
GE GDF630PGMWW
Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and electrical function
🔒 Secure Door Locking – Ensures dishwasher runs only when door is properly closed
⚙️ Fixes Start Issues – Resolves no-start or cycle interruption problems
🧩 Direct-Fit Design – Installs without modification
💰 Cost-Effective Repair – Affordable alternative to OEM door latches
📐 Product Specification
Part Number: WD01X29878
Component Type: Dishwasher Door Latch Assembly
Function: Door locking and safety interlock
Mounting: Screw-mounted, plug-in harness
Application: Dishwasher door safety system
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver
⚠️ Safety First: Unplug the dishwasher or turn off the breaker before servicing to avoid electrical shock.
Basic Steps:
Disconnect dishwasher power.
Remove the inner door panel screws.
Locate and disconnect the old door latch assembly.
Remove mounting screws and take out the latch.
Install the new XPARTCO WD01X29878 latch.
Reconnect wiring and reassemble the door panel.
Restore power and test operation.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore secure dishwasher operation and prevent door-related errors — Add to Cart Now for a dependable, budget-friendly repair!
6601EN1003D Washer Door Lock Interlock Switch
Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.
This is an aftermarket part that can be used as a replacement for the OEM part.
WARNING: California’s Proposition 65 (California Residents Only)
XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers
Product Description
Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts.
Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model.
Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083.
Compatibility:
Compatible with models including but not limited to:
Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS
Other brands: Select models requiring DC96-01703G
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G.
🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes.
🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA).
Product Specification
Part Number: XPDC96-01703G
Component Type: Washer water level pressure switch
Material: Durable plastic housing with metal contacts
Terminal Type: Electrical connector.
Operating Conditions: Suitable for high-humidity washer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the washer from the power source and water supply before installation.
Tools Needed: Phillips screwdriver, work gloves.
Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today!
Add to cart now for a budget-friendly fix!
Genuine OEM WH02X24374 Washer Agitator Screw
The Genuine OEM GE WH02X24374 is a 1/4-20, class 2A Sinuloc screw for GE and Hotpoint washers. GE catalogs it as "Screw, 1/4-20, 2A Sinuloc," and retailers list it for agitator repairs, where it is commonly replaced along with the agitator or agitator base. A missing, stripped, or damaged screw can leave the agitator loose or keep the washer from agitating properly.
This is the original GE part. Retailers do not agree on exactly where the screw is used, so check your model's parts diagram to confirm that it is the screw your washer calls for.
Quick Answer
The Genuine OEM WH02X24374 Agitator Screw replaces a lost, stripped, or damaged 1/4-20 screw on a GE or Hotpoint washer, most often during an agitator repair. Classic symptom: the washer will not agitate, or the agitator is loose, and the old screw is missing or has stripped threads.
Common Problems This Part Fixes
Washer will not agitate
Loose or wobbling agitator
Missing screw after an agitator or agitator base repair
Stripped, damaged, or corroded screw threads
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This screw directly replaces the following part numbers:
WH02X24374, 4587952, AGE26439, AP6027539, EAP11759130, PD00042816, PS11759130
Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This screw is listed for GE and Hotpoint washers, including these examples:
GE GTW220ACK1WW, GTW330ASK4WW, GTW335ASN0WW, GTW385ASW0WS
GE GTW460ASJ3WW, GTW460AMJ0WW, 5TW4307SW0WS, ETW485ASW0WB
Hotpoint HTW200ASK4WW, HTW240ASK6WS
Note: The models above are a small sample of a longer list, not a full list. Check your model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM GE screw for GE and Hotpoint washers
1/4-20 thread, class 2A
Often replaced along with the agitator or agitator base
Easy repair, typically under an hour
Product Specifications
Part Number
WH02X24374
OEM Part Number
WH02X24374
Part Type
Washer Screw (Agitator Repair)
Thread
1/4-20, Class 2A
Condition
Genuine OEM
Application
GE & Hotpoint Washers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Follow your model's service guide to reach the screw, thread the new screw into position, and tighten it firmly without over-tightening, which can strip the threads. If you are replacing an agitator or agitator base, install the screw as shown in your model's parts diagram.
Frequently Asked Questions
Is this the screw that holds my agitator on?
Retailers list it for agitator repairs and often sell it with the agitator, but they do not all spell out its exact location. Check your model's parts diagram or contact our support team before ordering.
What size is this screw?
It is a 1/4-20, class 2A screw. The length is not listed by the retailers we checked, so compare it to your old screw.
How many screws are included?
Retailers sell it as a single part, but do not state a pack count. Contact our support team if you need to confirm the quantity.
Will this fit my washer?
It is listed for many GE and Hotpoint washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE01X30638 Laundry Center Control Knob
The XPARTCO WE01X30638 is an aftermarket replacement control knob compatible with select GE, Hotpoint, RCA, and Kenmore GE-built laundry centers (stacked washer/dryer combination units). The control knob mounts on the timer or cycle selector shaft on the laundry center's control panel — it's what you grip and turn to choose wash cycles, dry cycles, and timer settings on both the washer and dryer sections of the unit. Because a stacked laundry center's knobs get twice the daily use of a standalone appliance (one control panel serving both washer and dryer functions), cracked and stripped knobs are one of the most common repairs on these units.
Constructed from durable black ABS plastic with a polished silver edge ring and an internal metal plate insert that grips the D-shaped control shaft — allowing precise detent positioning so you land exactly on your desired cycle setting. Approximately 2" in diameter with thick inner walls to resist the cracking that plagues aging original knobs. Snap-on installation — pulls straight off, pushes back on, no tools required. This is the current production version, directly superseding WE01X24776. It also replaces 4961358, AP6996856, PS16226089, and EAP16226089. Installs in under 1 minute — no tools required.
Quick Answer
The XPARTCO WE01X30638 Laundry Center Control Knob replaces a cracked, stripped, or missing control knob on GE, Hotpoint, RCA, and Kenmore GE-built stacked laundry centers. Black ABS plastic with polished silver edge, ~2" diameter, internal metal plate for a firm shaft grip. Snap-on — no tools required. Current part superseding WE01X24776; also replaces 4961358, AP6996856, PS16226089, EAP16226089. Compatible with GE GUD27ESPM0DG, GUD27ESPM1DG, GUD27GSPM0DG, GUD27GSPM1DG and related GUD27 series laundry centers.
Common Problems This Part Fixes
Control knob cracked or split from age and repeated use — the most common failure on GUD27-series laundry centers
Knob spinning freely on the shaft — internal grip stripped, no longer changing settings when turned
Knob difficult to turn or not responding — worn internal metal plate no longer engaging the shaft
Knob missing entirely from the control panel
Knob loose and wobbling on the shaft — imprecise cycle selection
Hairline cracks visible around the knob's shaft opening — early-stage failure that will soon strip
Knob damaged from impact or overtightened grip
Replacing multiple aging knobs at once — original knobs from the same production era tend to crack around the same time
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This laundry center control knob directly replaces the following OEM and cross-reference part numbers:
WE01X30638, WE01X24776, AGE25575, AP6996856, EAP16226089, PD00068517, PS16226089.
WE01X30638 is the current production part superseding WE01X24776. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This control knob is compatible with select laundry centers (stacked washer/dryer units) from the following brands:
GE laundry centers — GUD27ESPM0DG (electric dryer) and GUD27ESPM1DG series
GE laundry centers — GUD27GSPM0DG (gas dryer) and GUD27GSPM1DG series
GE laundry centers — related GUD27 series models (verify with parts diagram)
Hotpoint laundry centers (select GE-built models)
RCA laundry centers (select GE-built models)
Kenmore / Sears laundry centers (select GE-built models)
Tip: If one knob on your laundry center has cracked, inspect the others — knobs from the same production era typically develop cracks around the same time. Since the replacement takes seconds and the knobs are identical, many customers order two or more at once and replace them all in a single session, avoiding a repeat order a few months later. This knob is approximately 2" in diameter — confirm your original knob's size matches before ordering.
Key Features
Control knob for laundry center timer and cycle selection — installs on the control panel shaft
Durable black ABS plastic construction with thick inner walls — resists the cracking common on aging original knobs
Polished silver edge ring for a clean, modern look that matches GE laundry center styling
Internal metal plate insert grips the D-shaped control shaft firmly — precise detent positioning for accurate cycle selection
Approximately 2" diameter with smooth mirror-polished surface for a comfortable grip
Snap-on installation — pulls straight off the shaft, pushes back on; no tools or hardware required
Current production part — directly supersedes WE01X24776
Replaces 4961358, AP6996856, PS16226089, and EAP16226089
Compatible with GE GUD27ESPM0DG/1DG and GUD27GSPM0DG/1DG laundry centers, plus Hotpoint, RCA, and Kenmore GE-built models
Aftermarket replacement built to OEM-equivalent quality standards
Quick replacement — installs in under 1 minute
Product Specifications
Part Number
XPWE01X30638
Supersedes
WE01X24776
Part Type
Laundry Center Control Knob (Timer / Cycle Selector)
Condition
Aftermarket Replacement
Application
Laundry Centers / Stacked Washer-Dryer Units (GE platform)
Diameter
Approximately 2"
Color
Black with polished silver edge
Material
ABS plastic with internal metal plate insert
Shaft Type
D-shaped shaft receiver
Installation
Snap-on — no tools required
Compatible Brands
GE, Hotpoint, RCA, Kenmore (GE-built)
Installation Notes
⚠️ Unplug Laundry Center Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Locate the old control knob on the laundry center's control panel. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools required). If the knob is cracked and spinning without releasing, wrap a soft cloth around it for extra grip, or gently pry it off with a plastic tool (avoid metal tools that could scratch the control panel). Once the old knob is off, inspect the metal control shaft — note the D-shape (flat side) of the shaft. If the shaft itself is damaged, worn round, or the timer behind it feels loose, the underlying timer or switch may also need attention. Align the new WE01X30638 knob's internal D-shaped receiver with the flat side of the shaft and push it firmly straight on until it seats fully. Rotate the knob through its full range to confirm it clicks into each detent position cleanly and the indicator lines up with the panel markings. Restore power and run a quick test cycle. If replacing multiple knobs, repeat for each position — they're all identical on compatible GUD27-series units. Tools needed: None (soft cloth optional).
Frequently Asked Questions
Why do the knobs on my GE laundry center keep cracking?
The original knobs on GUD27-series laundry centers are subject to constant rotational stress concentrated at the D-shaped shaft opening — and on a stacked laundry center, one control panel serves both the washer and dryer, so the knobs see roughly double the daily turning of a standalone appliance's controls. Over years of use, hairline cracks form at the shaft opening and gradually spread until the knob's grip strips and it spins freely. The replacement knob's thick inner walls and internal metal plate insert are designed to resist this failure pattern. If one of your knobs has cracked, check the others — knobs from the same production era typically crack around the same time, and replacing them together saves a repeat order.
What's the difference between WE01X30638 and WE01X24776?
These are the same control knob across production revisions. WE01X24776 was the earlier GE part number, and WE01X30638 is the current production version that GE issued as its direct replacement. Both are physically and functionally interchangeable — if your laundry center's parts diagram shows WE01X24776, the WE01X30638 is the correct current replacement, and this listing covers both numbers. There may be a very slight color variation between the new knob and your aged originals, but the fit and function are identical.
How do I remove the old knob if it's cracked and just spins?
When the internal grip has stripped, the knob spins on the shaft instead of pulling off cleanly. Wrap a soft cloth around the knob for extra grip and pull firmly straight out while wiggling slightly. If that doesn't work, gently work a plastic pry tool (a plastic putty knife or old credit card) behind the knob's base and lever it outward evenly around its circumference. Avoid metal tools, which can scratch the control panel. If the knob is badly cracked, you can also carefully break away the remaining plastic to free it from the shaft. Once removed, the new knob pushes straight on.
Does this knob work for both the washer and dryer controls on my laundry center?
Yes — on compatible GUD27-series laundry centers, the control knobs across the panel are the same part, whether they operate washer cycle selection, dryer timer, or other rotary controls that use the same D-shaped shaft. If you're replacing more than one knob, a single part number covers all matching positions. Just confirm each position's knob is the same ~2" diameter style before ordering multiples — if your unit has a visibly different-sized knob at any position, verify against the parts diagram first.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable ABS plastic with an internal metal plate insert to match the dimensions (~2" diameter), D-shaped shaft receiver, snap-on installation, and appearance of the original WE01X30638/WE01X24776 control knob used in compatible GE, Hotpoint, RCA, and Kenmore GE-built laundry centers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
