Search results for "dryer idler pulleys"

WH08X10024CM Washer Drive Belt 1300J7 Poly-V auto tension belt. 7 Rib. Fits GE front load washers. Replaces Part numbers:WH08X10024, 1168664, AH1020114, AP3884128, EA1020114, PS1020114. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WDH8FT Washer Universal 8' Corrugated Drain Hose 8 foot. Corrugated plastic hose fits 1", 1-1/8", 1-1/4" & 1-3/8" outlets for Whirlpool, Kenmore, GE, Frigidaire & most other brands. Cross Reference: WDH8FT, TJ78WDH, AP5330761, 600-8P, 8WDH, ERSSD8, HP396, HP408, R87-408, SSD-8, SSD8, OEM15992288, WDH8FT. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov  

Read more less

WR60X10257 (OE) Refrigerator Evaporator Fan Motor The WR60X10257 is an OE (Original Equipment) evaporator fan motor, also known as an AC/DC fan motor, for GE and Hotpoint refrigerators. Located at the back of the freezer, this motor circulates air across the evaporator coils, which convert refrigerant into cooling capacity — the fan is what carries that cold air into both the freezer and fresh food compartments. Rated 115V, 60Hz, 2.4W. Common failure causes include worn motor bearings and general electrical wear. A failing motor produces a recognizable symptom: the freezer may stay reasonably cold while the fresh food section runs warm, since the fresh food compartment depends entirely on this fan to receive circulated cold air. Other symptoms include unusual noise from the freezer or inconsistent cooling overall. It directly replaces 1373246, 200D5001P003, AP4318644, EAP1766252, PS1766252, AH1766252, UDQR002GNL, WR60X10129, AGE29237, and PD00028496. Quick Answer The WR60X10257 (OE) Refrigerator Evaporator Fan Motor fixes GE and Hotpoint refrigerators where the freezer stays cold but the fresh food section runs warm, there's unusual noise from the freezer, or cooling is inconsistent. 115V, 60Hz, 2.4W. Replaces 1373246, 200D5001P003, AP4318644, EAP1766252, PS1766252, AH1766252, UDQR002GNL, WR60X10129, AGE29237, PD00028496. This is a 115V AC-powered motor — a different design from the 9.75V DC evaporator fan motors in our WR60X10074, WR60X10185, and WR60X10318 listings. Always match your original motor's voltage type before ordering. Common Problems This Part Fixes Freezer stays cold but the fresh food compartment runs warm Refrigerator or freezer sections too warm overall Unusual noise — humming, buzzing, or grinding — coming from the freezer Inconsistent or fluctuating refrigerator temperatures Refrigerator running constantly as it struggles to maintain temperature Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand What Is an OE Part? OE (Original Equipment) means this part is manufactured by the same original supplier that produces the Genuine OEM version — identical fit, materials, and performance. The only difference is packaging: OE parts ship under our XPARTCO brand rather than the appliance manufacturer's branded box, which is why they can't be listed as Genuine OEM. You get factory-original quality at a more affordable price. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10257, 1373246, 200D5001P003, UDQR002GNL, WR60X10129, AP4318644, EAP1766252, PS1766252, AGE29237, PD00028496 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE and Hotpoint refrigerators, and also fits select Haier, Monogram, and Café refrigerators built on the GE platform, including model numbers such as ETS22SBPARBS, ETS22SBSARSS, and GTS22FBPBRWW. Note — 115V AC, not 9.75V DC: This motor is a different design and voltage class from the DC evaporator fan motors used on other GE refrigerator platforms, including our WR60X10074, WR60X10185, and WR60X10318 listings (all 9.75V DC). Check your old motor's voltage rating, printed on the motor itself, before ordering — a DC motor and this AC motor are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features OE (Original Equipment) evaporator fan motor, also known as an AC/DC fan motor Circulates air across the evaporator coils to cool the freezer and fresh food compartments Resolves "freezer cold but fridge warm," "unusual noise," and "inconsistent cooling" symptoms caused by fan motor failure Rated 115V, 60Hz, 2.4W Direct drop-in replacement matching the original mounting and blade fitment Replaces 1373246, 200D5001P003, AP4318644, EAP1766252, PS1766252, AH1766252, UDQR002GNL, WR60X10129, AGE29237, and PD00028496 Compatible with GE, Hotpoint, Haier, Monogram, and Café refrigerators OE (Original Equipment) — manufactured by the same original supplier as the Genuine OEM part Product Specifications Part Number WR60X10257-OE Part Type Refrigerator Evaporator Fan Motor Designation OE (Original Equipment) Compatible Brand GE Location Back of the freezer, over the evaporator coils Voltage 115V AC Frequency 60 Hz Wattage 2.4 W Dimensions 4"H x 2-3/4"W x 17"D Quantity 1 fan motor Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is typically through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator coil and fan assembly. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the wiring harness connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation. Mount the new WR60X10257 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My freezer is cold but the fridge section is warm. Is this the right part? Yes, this is a very common and telling symptom pattern. The freezer sits close to the evaporator coil and can stay reasonably cold through proximity even with weakening air circulation, but the fresh food compartment depends entirely on this fan pushing cold air through the ducting to reach it. When the fan motor fails or slows down, the fresh food side is usually the first and most noticeably affected area. How do I know if I need this 115V motor or one of your DC motors? Check the voltage rating printed directly on your old motor before ordering. This WR60X10257 is a 115V AC-powered motor, while our WR60X10074, WR60X10185, and WR60X10318 listings are all 9.75V DC motors used on different GE refrigerator generations. The two motor types are not interchangeable, so matching the voltage rating on your original motor is the most reliable way to confirm which one you need. Is this a genuine OEM part? This is an OE (Original Equipment) part sold under our XPARTCO brand. OE parts are manufactured by the same original supplier that produces the Genuine OEM part, so the fit, materials, and performance are identical — the difference is that OE parts ship in XPARTCO packaging rather than the appliance manufacturer's branded box, which is why we can't list them as Genuine OEM. This gives you factory-original quality at a more affordable price than the branded version. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5040JA2009B Genuine OEM LG Refrigerator Motor Damper Grommet (Front) The 5040JA2009B is a genuine LG OEM front evaporator motor grommet for LG and select Kenmore refrigerators, and also fits select freezers. This rubber grommet cushions and secures the front side of the evaporator fan motor's mount, reducing vibration and noise as the motor runs. It's the front-position counterpart to our 5040JA2004A rear grommet — LG mounts this evaporator fan motor from both the front and rear with matching grommets working together. Made of rubber, this grommet naturally degrades from prolonged use, exposure to the freezer's cold temperatures, or physical damage from an accidental impact during cleaning or organizing. Once it fails, the evaporator motor loses proper cushioning and can shift slightly out of alignment. Symptoms of a bad grommet include increased noise and vibration, particularly noticeable when the evaporator fan motor is running, along with a rattling or buzzing sound coming from the freezer area. It directly replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, and 5040JQ2003B. Quick Answer The 5040JA2009B Genuine OEM LG Refrigerator Motor Damper Grommet (Front) fixes LG and select Kenmore refrigerators with increased noise or vibration from the evaporator fan motor, or a rattling/buzzing sound from the freezer area. Rubber, front-position grommet for the evaporator fan motor. Replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, 5040JQ2003B. This is the front counterpart to our 5040JA2004A rear grommet — both support the same evaporator fan motor from opposite sides. Common Problems This Part Fixes Increased noise or vibration from the evaporator fan motor Rattling or buzzing sound coming from the freezer area Noise that's especially noticeable when the fan motor is running Evaporator motor that has shifted slightly out of alignment Visibly cracked, hardened, or damaged rubber grommet Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This motor damper grommet directly replaces the following OEM and cross-reference part numbers: 5040JA2009B, AP4443769, 1268013, AH3526237, EA3526237, PS3526237, 5040JQ2003B If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This front evaporator motor grommet is compatible with select LG refrigerators and freezers, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as LFXC24726S, LMXS30776S, LSC27950ST, LFC20760SB, LFX25960SB, and LFX28968ST/02. Note — front grommet, not rear: This is the front-position evaporator motor grommet. The matching rear-position grommet for the same motor is a separate part, our 5040JA2004A listing. Both are typically checked and often replaced together, since they support the same motor and are usually the same age. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified rubber compound and fit Cushions and secures the front side of the evaporator fan motor mount Resolves "increased motor noise," "vibration," and "rattling/buzzing from the freezer" symptoms Front-position counterpart to our 5040JA2004A rear grommet Durable rubber construction designed for the freezer's cold operating environment Direct drop-in replacement — no tools required for the grommet itself Replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, and 5040JQ2003B Compatible with LG and select Kenmore refrigerators and freezers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5040JA2009B Part Type Front Evaporator Motor Grommet Condition Genuine OEM Brand LG Material Rubber Function Cushions and secures the front side of the evaporator fan motor mount Position Front Related Part 5040JA2004A (rear-position grommet for the same motor, sold separately) Repair Difficulty Moderate — freezer teardown required for access Quantity 1 damper grommet Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Photograph Wiring Before Disconnecting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access to the evaporator motor on many models requires going in through the freezer: empty the top half of the freezer, remove the side rails holding the ice bin, then remove the outer screws holding the ice auger assembly — on many models this means only the two outer screws on each side, not the middle ones. With the ice maker components clear, remove the rear panel to access the evaporator fan motor and its front and rear grommets. Photograph the wiring connections carefully before disconnecting anything, since several wires can look interchangeable but are not, and reconnecting one in reverse can cause a malfunction. Remove the old front grommet from the motor mount — it typically pulls free without tools. Press the new 5040JA2009B grommet into the same position, seating it fully. If the rear grommet is also worn, this is a good time to replace it as well since you already have access. Reassemble the ice maker components, rear panel, and any other parts removed for access, restore power, and run the refrigerator for a while to confirm the noise or vibration has resolved. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions Should I replace the rear grommet at the same time as this front one? It's worth considering. Both grommets support the same evaporator fan motor from opposite sides and are typically the same age, so if one has degraded, the other is often not far behind. Since accessing the motor for this repair already requires a fair amount of teardown, replacing both together — our 5040JA2004A rear grommet and this front one — saves you from repeating the same access work again soon after. Why do I need to go through the ice maker to reach this part? On many LG refrigerator models, the evaporator fan motor and its grommets sit behind the freezer's ice maker assembly, so reaching them requires removing the ice bin, its side rails, and the auger mechanism first. This is a more involved access path than some other freezer repairs, so budget extra time and take photos as you go to keep track of how everything reassembles. Why is it so important to photograph the wiring before disconnecting? Several of the wires in this area can look similar and are easy to connect in reverse or in the wrong position, which can cause a malfunction after reassembly. Taking clear photos of each connection before you disconnect anything is a simple step that prevents a frustrating troubleshooting session later. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound and mounting fit of the front evaporator motor grommet originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X26637 Washer Water Valve The XPARTCO WH13X26637 is an aftermarket replacement quad water inlet valve for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models. This valve controls the flow of water into the washer from the household supply line, using two internal valves — each with its own wire terminals — to manage water flow and temperature blending for the wash cycle. When the control calls for a fill, the corresponding solenoid opens to admit water and closes once the correct level is reached. Rated 120V, 6/5W. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve produces a clear set of symptoms: the washer not starting, an error code related to water fill, or — one of the most common complaints — water continuing to drip into the tub between cycles even when the washer isn't running, since a worn internal seal can fail to shut off completely. It directly replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665. Quick Answer The XPARTCO WH13X26637 Washer Water Valve fixes GE top-load washers (and select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models) that won't start, show a water-fill error code, or have water dripping into the tub between cycles. Quad valve design — 2 valves, each with its own wire terminals. 120V, 6/5W. Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, PD00037665. Dripping into the tub between cycles, even with the washer off, is a classic sign of a worn valve seal that isn't shutting off completely. Common Problems This Part Fixes Washer won't start Error code related to water fill displayed on the control panel Water dripping into the tub between cycles, even when the washer isn't running Washer filling slowly or only partially No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, 4546358, AGE26282, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X24058, WH13X26637-25PK, PD00037665 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore washers built on the GE platform, including model numbers such as: GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS GTW685BPL0DG, GTW750CPL1DG, GTW720BSN0WS PTW605BPR1DG, PTW605BSR0WS, PTW605BSR1WS PTW700BPT0DG, PTW700BST0RS, PTW700BST0WS PTW705BPT0DG, PTW705BST0RS, PTW705BST0WS Note: This is a top-load washer valve, distinct from GE's front-load valves used on other GE washer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement quad water inlet valve — two valves, each with its own wire terminals Resolves "won't start," "water fill error code," and "dripping into the tub between cycles" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Rated 120V, 6/5W Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665 Compatible with GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair, typically 15 to 30 minutes Product Specifications Part Number XPWH13X26637 OEM Part Number WH13X26637 Part Type Washer Quad Water Inlet Valve Condition Aftermarket Replacement Application Top-Load Washers Voltage 120V Wattage 6/5 W Valve Design Quad — 2 valves, each with separate wire terminals Repair Difficulty Easy — 15 to 30 minutes Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, RCA, Café, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves at the wall before beginning. Wear work gloves. Unscrew the hot and cold supply lines from the bottom of the old valve, then carefully pull the valve assembly away from the wall for access. Photograph the wiring and hose connections before disconnecting anything, since this valve has two separate wire terminal sets and multiple outlet hoses. Remove the cover securing the valve in place, disconnect the electrical connectors and outlet hoses, and take out the old valve — the entire assembly typically comes out in one piece. Insert the new WH13X26637 into the same opening, making sure it fits tightly and securely, and secure it with screws. Reconnect all outlet hoses to their original positions, reconnect the electrical connectors fully, and put the cover back on. Reconnect the hot and cold supply lines, tightening securely. Turn the water supply back on and check for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: screwdriver, spanner, pliers or adjustable wrench, work gloves. Frequently Asked Questions Water keeps dripping into my washer tub even when it's not running. Is this the valve? Yes, this is one of the most common symptoms of a failing valve, and a well-documented one for this exact part. If you've already checked the hoses and confirmed they're not the source of the leak, a worn internal seal in the valve is the most likely remaining cause — the seal fails to shut off completely, letting a small amount of water continue dripping through even between cycles. Shutting off the water supply is a temporary workaround, but replacing the valve is the permanent fix. Why does this valve have two sets of wire terminals? This is a quad valve design, meaning it houses two separate internal valves in one assembly, each with its own electrical connection. This allows the washer to independently control different water functions — such as hot and cold fill — from a single combined unit rather than requiring two completely separate valve housings. Is this a top-load or front-load washer valve? This is a top-load washer valve, compatible with GE's GTW and PTW model series. It's a different valve design from the ones used on GE's front-load washer platforms, so confirm your washer type and model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the quad valve design, wattage, and connection type of the original WH13X26637 valve used in compatible GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) The XPARTCO 8318314 is an aftermarket replacement 352°F thermal cutoff fuse compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers. The thermal cutoff fuse is a critical safety device mounted near the heating element housing — it acts as a backup safety in case the high-limit thermostat fails to open. When the air temperature inside the heating element area reaches 352°F, the fuse permanently opens and cuts power to the heater circuit, preventing the dryer from continuing to overheat and creating a fire risk. This is a one-time fuse — once it has tripped, it cannot be reset and must be replaced. White and gray metal/ceramic construction. Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H, with approximately 1-5/8" between mounting holes (center to center). It directly replaces 8318314. Important: when the thermal cutoff blows, the high-limit thermostat (8557403 — sold separately) is often also stressed and should be tested or replaced at the same time. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) fixes Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers that suddenly stopped heating after an overheat event. One-time fuse — 352°F open, must be replaced once blown. 1-1/4"L x 1-1/4"W x 2-3/16"H, ~1-5/8" between mounting holes. Metal/ceramic. Often replaced alongside the high-limit thermostat (8557403, sold separately). Common Problems This Part Fixes Dryer suddenly stopped heating with no warning — thermal cutoff has blown after an overheat event Dryer runs and tumbles normally but produces no heat No-heat fault following a partially blocked exhaust vent or restricted airflow event Multimeter continuity test shows the cutoff has an open circuit (no continuity) Visible damage or discoloration around the thermal cutoff housing from a prior overheat event Repeated no-heat problems where the thermal cutoff has tripped more than once Replaces Part Numbers This thermal cutoff fuse directly replaces the following OEM and cross-reference part numbers: 8318314 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This 352°F thermal cutoff fuse is compatible with select dryers from the following brands: Whirlpool dryers (Elite, Cabrio, Duet, and WED series — select models including WED9200, WED7300, WED7400, WED7600 and related) Maytag dryers (Maxima and MED series — select models including MED3500, MED6000XW, MEDE900VW and related) KitchenAid dryers (select models) Kenmore / Sears dryers — Elite 110-series and related Whirlpool-built models Amana dryers — NED and YNED series (select models including NED7500VW1 and related) Crosley dryers (CED series and related models) Roper dryers (select models) Inglis dryers (select models) Estate dryers (select models) Important — Check Vent Before Restarting: A blown thermal cutoff is almost always the result of restricted dryer airflow. Before replacing this fuse and restoring service, thoroughly clean the dryer's exhaust vent line all the way to the exterior wall outlet, the lint screen, and any internal lint buildup. Installing a new thermal cutoff without fixing the underlying airflow problem will cause the new fuse to blow within a short time, repeating the failure. Key Features 352°F one-time safety fuse — permanently opens to cut power to the heater circuit if the dryer overheats Backup safety device — protects against overheating in case the high-limit thermostat fails to open Cannot be reset — must be replaced once blown Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H; approximately 1-5/8" between mounting holes (center to center) Metal and ceramic construction in white/gray Often replaced together with the high-limit thermostat (8557403, sold separately) as a paired safety repair Compatible with Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8318314 Part Type Dryer Thermal Cutoff Fuse (Safety Fuse) Condition Aftermarket Replacement Application Electric and Gas Dryers (Whirlpool platform) Trip Temperature 352°F Fuse Type One-Time (must be replaced once blown — cannot be reset) Dimensions 1-1/4"L x 1-1/4"W x 2-3/16"H Mounting Hole Spacing Approx. 1-5/8" center to center Color White / Gray Material Metal / Ceramic Often Replaced With High-Limit Thermostat (8557403, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, Estate Installation Notes ⚠️ Unplug Dryer Before Starting — Clean Vent System First Disconnect power before beginning. Wear work gloves to protect your hands. Before installing the new thermal cutoff, thoroughly clean the dryer's vent line — from the lint screen through the duct to the exterior wall outlet, plus any internal lint buildup around the heater housing. A blown thermal cutoff is virtually always caused by restricted airflow; if you don't fix the underlying cause, the new fuse will trip again soon. Access the thermal cutoff by removing the rear (or front, depending on model) access panel of the dryer to expose the heating element housing. The 8318314 thermal cutoff is mounted on or near the heater housing. Photograph the wire connections before disconnecting. Disconnect the wires from the old cutoff and remove the mounting screw(s). Install the new 8318314 cutoff in the same position and reconnect the wires. While the panel is open, this is also the ideal time to test or replace the high-limit thermostat (8557403) — overheat events that blow this fuse often damage that component too. Reassemble the panel, restore power, and run a test heat cycle to confirm normal heat operation. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter, work gloves. Frequently Asked Questions What's the difference between a thermal cutoff, a thermal fuse, and a high-limit thermostat? All three are safety components in a dryer's heating circuit but they serve different roles. The high-limit thermostat (such as 8557403 or 3391914) is a resettable safety switch — it opens when the air gets too hot, then closes again automatically once it cools. The thermal cutoff (8318314, 352°F) is a one-time fuse on the heating element circuit — it blows permanently if the temperature exceeds 352°F, meaning the high-limit thermostat failed to do its job. The thermal fuse (often 3392519) is a separate one-time fuse mounted on the exhaust duct — it blows if exhaust airflow temperature exceeds its rating. Each protects against a different failure mode and is replaced individually when it blows. Why did my thermal cutoff blow in the first place? A blown thermal cutoff is almost always the result of restricted airflow through the dryer. The most common causes are: a clogged or kinked exhaust vent line, a clogged lint screen, lint buildup inside the dryer cabinet near the heater housing, or a failed blower wheel/motor that's not moving enough air. Less commonly, a failed high-limit thermostat (stuck closed) can let the dryer overheat until the thermal cutoff blows as a last-resort safety. Before replacing this part, identify and fix the underlying airflow issue — otherwise the new fuse will blow within a short time. Should I replace the high-limit thermostat at the same time? Yes, it's highly recommended. The thermal cutoff is the second line of defense against overheating — for it to trip, the high-limit thermostat ahead of it likely failed to open at its normal cycling temperature, was stressed by the overheat event, or was already weakened. Replacing the high-limit thermostat (8557403 on many compatible Whirlpool-platform dryers) at the same time is standard practice and ensures both safety components work correctly together. The 279973 kit even bundles a thermal cutoff with a high-limit thermostat for this reason. Can the thermal cutoff be reset like a circuit breaker? No — the 8318314 is a one-time thermal fuse. Once it opens at 352°F, it permanently breaks the electrical circuit and cannot be reset. Some appliance components (like a high-limit thermostat) can reset automatically as they cool, but a thermal cutoff fuse is a single-use safety device by design. If your dryer suddenly stopped heating and a continuity test on this fuse shows an open circuit, it must be replaced. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and ceramic with the same 352°F trip temperature, dimensions (1-1/4"L x 1-1/4"W x 2-3/16"H), and mounting hole spacing (1-5/8" center to center) as the original 8318314 thermal cutoff fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

809069207 Refrigerator Genuine OEM Evaporator Fan Motor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Restore powerful and consistent cooling with the 809069207 Refrigerator Genuine OEM Evaporator Fan Motor. This factory-approved motor circulates cold air throughout the refrigerator and freezer compartments, ensuring even temperature distribution. A failing fan motor can cause warm spots, frost buildup, poor cooling, or unusual noises. Replacing it with this Genuine OEM part ensures dependable performance and the same airflow efficiency your appliance had when new. Replaces Part Numbers 809069207, PD00064424, EAP12705983, AP6834878, PS12705983. Compatibility This Genuine OEM evaporator fan motor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to):Frigidaire FFHS2622MB3, FFSS2615TS0, Electrolux EI23CS55GS1, and Kenmore 253.7031321A. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for perfect fit and long-lasting performance ❄️ Restores Air Circulation – Ensures even cooling in fresh food and freezer sections 🔇 Quiet Motor Operation – Balanced OEM motor design lowers noise and vibration 💪 High Durability – Built with premium materials for extended service life 🛡️ Fixes Common Issues – Solves poor cooling, frost buildup, noisy fan, or warm temperatures 📐 Product Specification Part Number: 809069207 Component Type: Refrigerator Evaporator Fan Motor Material: Reinforced plastic fan housing with factory motor Voltage: 115V AC (model dependent) Mounting: Direct-fit motor mounted behind freezer interior panel Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before servicing to avoid electrical shock. Steps: Disconnect power and remove freezer shelves and panels. Locate the evaporator fan assembly. Disconnect the wiring harness and remove the old motor. Install the new 809069207 motor in the same location. Reassemble interior panels and restore power. Allow several minutes for airflow to stabilize. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore powerful, even cooling — Add to Cart Now for a factory-quality repair!

Read more less

5304523741 Refrigerator Genuine OEM Evaporator Fan Motor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling efficiently with the 5304523741 Refrigerator Genuine OEM Evaporator Fan Motor. This factory-approved replacement circulates cold air from the evaporator throughout the refrigerator and freezer compartments. A failing fan motor can cause uneven temperatures, frost buildup, or warm sections in your fridge. Installing this genuine OEM part ensures quiet, dependable air circulation and consistent cooling performance. Replaces Part Numbers 5304523741, AP6983831, EAP12746805, 4960926, PD00067011, PS12746805. Compatibility This genuine OEM fan motor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFSS2615TS0, Electrolux LFHB2751TF, and Kenmore 253.70313214. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Factory-approved motor for reliable cooling performance ❄️ Efficient Air Circulation – Distributes cold air evenly throughout the compartments 💰 Energy-Efficient Operation – Restores temperature consistency and reduces compressor strain 🛠️ DIY Friendly – Direct-fit replacement installs in minutes 🛡️ Fixes Common Issues – Solves warm freezer, frost buildup, or noisy fan motor problems 📐 Product Specification Part Number: 5304523741 Component Type: Refrigerator Evaporator Fan Motor Material: Metal and high-temperature plastic housing Mounting: Direct-fit replacement in freezer compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove freezer shelves and back panel. Locate and disconnect the wiring harness from the old fan motor. Remove mounting screws and take out the old motor and fan blade. Transfer the fan blade (if required) to the new 5304523741 motor. Mount the new motor, reconnect wiring, and reinstall back panel. Restore power and confirm even cooling and quiet operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🧊 Genuine OEM Replacement Part 🔄 30-Day Return Policy Keep your refrigerator running at peak performance — Add to Cart Now for a genuine, factory-approved repair!

Read more less

2187145 Refrigerator Genuine Compressor Overload Replaces Part Numbers: WP2187145, OEM24024106, AP6006026, 2187145, 2-34286-038, 4431117, 8206664, PS11739089, W10306725. Description: This Compressor Overload is a Genuine OEM part for specific Whirlpool, Kenmore refrigerator models.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERP DC97-05280W Washer Suspension Rod Replaces Part Numbers: DC97-05280W, 3998024, AP5966911, PS11719937   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact. Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482. Common Problems This Part Fixes Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit Dryer takes much longer than normal to dry a load Dryer tumbles normally but generates no heat during the cycle No heat even after the thermal fuse has already been replaced — thermostat also failed Dryer overheating intermittently — thermostat not opening at the correct temperature Multimeter test shows open circuit (no continuity) across the thermostat at room temperature Replaces Part Numbers This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers: 6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform. LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models) LG electric dryers — DLEX series (select models) LG gas dryers — DLG series (DLG2051W, DLG3788W and related models) LG gas dryers — DLGX series (select models) LG electric and gas dryers — DLB series (select models) Kenmore / Sears dryers — 796-series (LG-built models) Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both. Key Features Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers 3-terminal design — matches the original wiring configuration on compatible heater housings Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center) Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application Mounts directly on the heater housing — accessible from the dryer back panel Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair Test with multimeter before replacing — should show closed continuity at room temperature Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6931EL3001F Part Type Dryer Rear Hi-Limit Heater Thermostat Condition Aftermarket Replacement Application LG and Kenmore Electric and Gas Dryers Thermostat Rating L125-31C — auto-resets after cooling Voltage 250V Amperage 25A Terminals 3-terminal Dimensions 2"L x 1-3/4"W x 1-1/4"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Gray / Black Material Metal / Plastic Location Heater housing (rear of dryer) Normal Behavior Closed continuity at room temperature Often Replaced With 6931EL3003D Thermal Fuse Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter. Frequently Asked Questions What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse? Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended. How do I test the 6931EL3001F thermostat with a multimeter? Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat. My LG dryer has no heat but the thermal fuse is good — could it be the thermostat? Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition. What does the "L125-31C" rating mean? The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304530651 Refrigerator Genuine OEM Evaporator Fan Motor 115V 60hz 2.8W Replaces Part Numbers: 5304530651, 242077704, AP7179350, PS16660872 Description: This Evaporator Fan Motor is a Genuine OEM part for specific Electrolux, Frigidaire refrigerator models. It is responsible for circulating air throughout the refrigerator’s interior to maintain consistent cooling and optimal temperature distribution. This motor works to move air over the evaporator coils, aiding in the cooling process and ensuring that the refrigerator and freezer compartments remain at the desired temperature.

Read more less