Search results for "dryer idler pulleys"

XPARTCO WR60X10074 Refrigerator Evaporator Fan Motor The XPARTCO WR60X10074 is an aftermarket replacement evaporator fan motor with thermistor for GE and Hotpoint refrigerators. This motor is located at the back of the freezer and circulates air across the evaporator coils, which convert refrigerant into cooling capacity — the fan is what carries that cooled air into both the freezer and fresh food compartments. Bundled with this motor is a separate thermistor that snaps onto the top portion of the evaporator and sends temperature signals back to the main control board, letting it regulate cooling accurately. Rated 9.75V DC, 3.25W — the same base motor used in our WR60X10185 listing, but this version ships with the thermistor included. GE's own guidance is direct on this point: the thermistor should be replaced at the same time as the evaporator fan, since the two are serviced together under this part number rather than sold and swapped independently. Common failure causes include worn motor bearings and general electrical wear. Symptoms include unusual noise from the freezer, a refrigerator or freezer section running too warm, or inconsistent temperatures overall. It directly replaces AP3191003, 914169, 197D4492G001, and 197D2039P013. Quick Answer The XPARTCO WR60X10074 Refrigerator Evaporator Fan Motor fixes GE and Hotpoint refrigerators with unusual noise from the freezer, a refrigerator or freezer section running too warm, or inconsistent cooling overall. 9.75V DC, 3.25W, includes thermistor. Replaces AP3191003, 914169, 197D4492G001, 197D2039P013. This is the motor-plus-thermistor version — if your old connector has no thermistor wire, you need our WR60X10185 listing instead; this is also a different assembly from our WR60X10318 side-by-side listing, which has the thermistor integrated into the motor's own harness rather than as a separate snap-on piece. Common Problems This Part Fixes Unusual noise — humming, buzzing, or grinding — coming from the freezer Fresh food compartment or freezer running too warm Inconsistent or fluctuating refrigerator temperatures Refrigerator running constantly as it struggles to maintain temperature Fan motor that has gone silent after previously running normally Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10074, 197D4492G001, 914169, AH304658, AP3191003, AGE29122, PD00001062, EA304658, PS304658 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE and Hotpoint refrigerators, including model numbers such as DSS25PFMCCC. Note — check your connector before ordering: This motor includes the thermistor. If your old motor's connector has no thermistor wire — a plain 4-wire harness with 2 empty pin slots on a 6-pin connector — you need our WR60X10185 listing instead (no thermistor). If your connector has a dedicated light connector, you need WR23X10467. This part is also a separate assembly from our WR60X10318 listing, a side-by-side platform motor with the thermistor built directly into its own 6-pin harness rather than snapping onto the evaporator as a separate piece. Even between similar GE thermistor-equipped motors, always verify your full model number, since GE support has confirmed these are not automatically interchangeable without checking your specific model. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Aftermarket replacement evaporator fan motor — circulates air across the evaporator coils to cool the freezer and fresh food compartments Includes a separate thermistor that snaps onto the top of the evaporator and reports temperature to the main control board Resolves "unusual noise," "running too warm," and "inconsistent cooling" symptoms caused by fan motor or thermistor failure Rated 9.75V DC, 3.25W Direct drop-in replacement matching the original mounting and blade fitment Replaces AP3191003, 914169, 197D4492G001, and 197D2039P013 Compatible with GE and Hotpoint refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WR60X10074 OEM Part Number WR60X10074 Part Type Refrigerator Evaporator Fan Motor with Thermistor Condition Aftermarket Replacement Brand GE Location Back of the freezer, over the evaporator coils Voltage 9.75V DC Wattage 3.25 W Includes Thermistor Yes — snaps onto the top of the evaporator, sold together Weight Approx. 0.6 lb. Quantity 1 fan motor + 1 thermistor Compatible Brands GE, Hotpoint Installation Notes ⚠️ Unplug Refrigerator Before Starting — Replace The Thermistor Along With The Motor Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator coil, fan, and thermistor. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the wiring harness connector, the fan blade's orientation, and the thermistor's snap-on position before disconnecting anything. Unplug the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Unsnap the old thermistor from the top of the evaporator and disconnect its wiring as well. Install both the new motor and the new thermistor together, even if only one of them tested as failed — GE's own guidance is to replace the thermistor whenever the evaporator fan is replaced, since they're serviced as a pair under this part number. Mount the new motor in the same position, reconnect the wiring harness connector, and snap the new thermistor onto the same spot on the evaporator, reconnecting its wiring. Confirm the fan blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I really need to replace the thermistor if only the fan motor stopped working? GE's official guidance is yes — the thermistor should be replaced along with the evaporator fan whenever this part number is used, since they're sold and serviced together as a pair rather than as fully independent components. That said, some technicians have successfully replaced just the fan motor alone in certain situations; if you want to attempt a fan-only swap, test your existing thermistor first and keep in mind this isn't the manufacturer-recommended approach. How do I know if I need this motor or the WR60X10185 (no thermistor) version? Look at your old motor's electrical connector before ordering. This WR60X10074 motor comes with a thermistor — if your connector has a thermistor wire running to it, this is the correct part. If your connector is a plain 4-wire harness with no thermistor wire and two empty pin positions on a 6-pin plug, you need our WR60X10185 listing instead, which does not include a thermistor. My fridge isn't cooling but the fan seems to spin fine. Could it still be this part? Yes — if the fan is spinning but the fridge still isn't cooling properly, the thermistor half of this assembly is worth suspecting, since a faulty thermistor can send incorrect temperature readings to the control board even while the fan motor itself works fine. One customer confirmed their control board and thermistor initially "checked good" before eventually tracing a similar symptom to fan circulation — so it's worth testing both components rather than assuming the fan alone is the issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the 9.75V, 3.25W motor design, blade fitment, and thermistor function of the original WR60X10074 evaporator fan motor and thermistor used in compatible GE and Hotpoint refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3977767 Dryer Hi Limit Thermostat 250 -80F Limit Thermostat. Fits specific Maytag, Kenmore, Whirlpool dryer models. Replaces Part Number: WP3977767, 3977767, 3399693, ER3977767, SET185, TJ90SET185, WP3977767VP, AP6009043, PS11742185. Description: This Hi-Limit Thermostat is a replacement part for specific Maytag, Kenmore, Whirlpool dryer models. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR60X10172 Refrigerator Genuine Evaporator Fan Motor 115V, .20A, 60Hz, 2800RPM, 2-5/8" shaft, Has quick disconnect. Replaces Part Numbers: WR60X10172, 1164351, AH967024, AP3855311, EA967024, IS-23210GEVA, PS967024, WR60X10057, WR60X10117, WR60X10190, WR60X10197.

Read more less

ERP DC97-05280S Washer Suspension Rod Replaces Part Numbers: DC97-05280S, 3998020, AP5799907, PS8764053   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERP WD12X10277 Dishwasher Lower Dish rack Roller Axle Single Pack Gray Color Replaces Part Number: WD12X10277, WD12X10075, WD12X10101, WD12X10126, WD12X10261   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WD19X25278 Dishwasher Genuine OEM Diverter Assembly Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077. Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.

Read more less

285785 Washer Transmission Clutch - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and Other Washers Product Description Restore your washer’s performance with the replacement 285785 Washer Transmission Clutch. This high-quality replacement clutch assembly, designed for direct-drive (beltless) Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and other washer models, connects the transmission to the inner tub during the spin cycle and the agitator during the wash cycle. Constructed from durable plastic and metal, this clutch assembly includes a clutch with liner, brake cam driver, retaining clip, blue spring for large capacity (27") washers, and black spring for compact (24") washers. It addresses issues like slow spinning, failure to agitate, burning smells, or excessive shaking. Note: Includes one clutch assembly with hardware. Disconnect power before installation. Replaces part numbers: 285785, 2670, 285331, 285380, 285422, 285540, 285761, 285785VP, 3350015, 3350114, 3350115, 3351342, 3351343, 387888, 388948, 388949, 3946794, 3946847, 3951311, 3951312, 62699, 63174, 63765, 64176, PD00002503, EAP334641, AH334641, EA334641, J27-662, LP326, AP3094537, PS334641. Compatibility: Compatible with models including but not limited to: Whirlpool: WTW5300SQ0, LSR7233EQ0, LSR8433KQ0, LSQ9544KQ0 Kenmore: 110.26902690, 110.28762790, 110.29822800 KitchenAid: KAWS750JQ0, KAWS850JQ0 Maytag: MAV6451AWW, MAV9750AWW Amana: NTW4500XQ0 Roper: RAS8245EQ1, RTW4440XQ0 Inglis: ITW4300SQ0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Inglis, and other direct-drive washer models. 🔥 Specifications: replacement clutch assembly, plastic and metal, 4-1/2"L x 4-1/2"W x 1-1/8"H, includes clutch w/liner, brake cam driver, retaining clip, blue spring (1.24" for large capacity 27" washers), black spring (1.46" for compact 24" washers). 💰 Cost-Effective Alternative: replacement clutch offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a socket set, screwdrivers, work gloves; typically installed in 1–2 hours. 🛡️ Reliable Fixes: Resolves slow spinning, failure to agitate, burning smells, excessive shaking, or noisy operation. Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your washer spinning and agitating smoothly today! Add to cart now for a budget-friendly fix!

Read more less

ERP DC97-16350C Washer Suspension Support Rod - Compatible with Samsung Washers Product Description Stabilize your washer with the replacement DC97-16350C Washer Suspension Support Rod. This replacement suspension rod and spring assembly is designed for select Samsung top-load washers, supporting the washer tub to minimize vibration and noise during operation. It addresses issues like excessive shaking, off-balance drums, or "DC" error codes, offering a cost-effective alternative to OEM parts. Note: Includes one suspension rod and spring assembly (approximately 25.6" long). Sold individually; recommend replacing all four rods for optimal performance. Disconnect power before installation. Verify compatibility with your washer model. Replaces part numbers: DC97-16350C, DC97-16350J, 3282689, DC97-05280K, PD00007282, EAP4221572, AP5623264, PS4221572. Compatibility: Compatible with models including but not limited to: Samsung: WA400PJHDWR/AA-01, WA400PJHDWR/AA-02, WA400PJHDWR/AA-03, WA422PRHDWR/AA-00, WA422PRHDWR/AA-01, WA422PRHDWR/AA-02, WA45H7000AW/A2, WA45M7050AW/A4 Other brands: Select models requiring DC97-16350C Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung top-load washers requiring DC97-16350C. 🔥 Specifications: Replacement suspension rod and spring assembly, approximately 25.6" long, designed to absorb shock and reduce vibration. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes per rod. 🛡️ Effective Fixes: Resolves excessive shaking, off-balance drums, noise, or "DC" error codes. Product Specification Part Number: DC97-16350C Component Type: Washer suspension support rod and spring assembly Material: Durable ABS plastic and metal with high-tension spring Dimensions: Approximately 25.6" L (rod and spring assembly) Operating Conditions: Suitable for high-vibration washer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves, optional pliers. Process: Access the washer tub, remove the old suspension rod, and install the new one, ensuring secure attachment to the tub and base. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 50561602 Heater Safety Thermostat  Compatible with Victory 50561602 Safety Switch, Heater, 250F

Read more less

PK136277-1 Lower Dishrack Roller and Axle Set Single Pack Replaces part Numbers: WD12X10136,  WD12X10277   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

17438100000436 Combo Washer / Dryer Genuine OEM Heating Element Genuine OEM heating element designed for select Midea and Magic Chef combo washer / dryer units to restore proper drying heat. ✓ Genuine OEM Part ✓ Replaces 17438100000436 ✓ Compatibility Support Product Description The 17438100000436 Combo Washer / Dryer Genuine OEM Heating Element is designed for select Midea and Magic Chef combo washer / dryer units. This heating element produces heat during the drying cycle and helps restore proper drying performance. A failed heating element can cause no heat, long drying times, damp clothes after the cycle, or inconsistent drying temperature. Quick Answer If your Midea or Magic Chef combo washer / dryer is not heating, takes too long to dry, or leaves clothes damp after the drying cycle, the 17438100000436 heating element may need replacement. ⚠️ Always verify your combo washer / dryer model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Combo washer / dryer not heating Clothes still damp after drying cycle Drying cycle takes too long Inconsistent drying temperature Failed or burned-out heating element Replaces part Number 17438100000436,  AP7157526, AP6984785, PS18188537 Compatibility This genuine OEM heating element fits select Midea and Magic Chef combo washer / dryer models using part number 17438100000436. Always verify your combo washer / dryer model number before ordering. Contact our support team if you’re unsure. Key Features Genuine OEM heating element Designed for select Midea and Magic Chef combo washer / dryer units Helps restore proper drying heat Supports reliable drying cycle performance Direct replacement component for compatible models Product Specifications Brand Midea / Magic Chef Part Type Combo Washer / Dryer Heating Element Primary Part Number 17438100000436 Compatible Appliance Type Combo Washer / Dryer Condition Genuine New Installation Disconnect power before installation. Inspect wiring, thermal fuse, thermostat, airflow path, and related heating components before testing appliance operation. Troubleshooting Guide ⚠️ Disconnect power before servicing the appliance. Check for lint buildup or airflow restrictions before replacing the heating element. Inspect the heating element for visible breaks, burns, or damage. Check related thermostats, thermal fuse, and wiring connections. Replace the heating element if no-heat or poor drying problems continue. When Should You Replace This Part? Replace the heating element if the Midea or Magic Chef combo washer / dryer does not heat, takes too long to dry, leaves clothes damp, or shows signs of a burned-out heating element. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Genuine Parts ✓ Compatibility Support ✓ Secure Checkout ```

Read more less