W10280608 Freezer Bracket
Bracket - Left Side
Replaces Part Numbers: WPW10280608, W10280608, W10187668, 12812301, 12812303, 4443902, 67004014, 8171234, AP6018544, PS11751846.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 3977394 Dryer Thermal Cut-Off Kit – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers
Product Description
Protect your dryer from overheating with the XPARTCO 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable XPARTCO 3977394 kit restores safe temperature control and helps prevent damage to internal components.
Replaces Part Numbers
XPTC352, 3977394, 352F, EXPTC352
Compatibility
This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers.
Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM safety and temperature performance
🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats
💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits
🛠️ Easy Installation – Direct-fit design with included thermostats and connectors
🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely
📐 Product Specification
Part Number: 3977394
Component Type: Dryer Thermal Cut-Off Kit
Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors
Temperature Rating: Cut-off opens at ~352°F.
Material: Metal thermostat housing and heat-resistant components
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Nut driver, Phillips screwdriver
⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock.
Steps:
Disconnect power and remove the rear dryer panel.
Locate the heating element housing and identify the cut-off and thermostat.
Disconnect wires and remove the old components.
Install the new 3977394 cut-off and thermostat in the same locations.
Reconnect wires, reassemble the back panel, and restore power.
Run a short test cycle to verify proper heating.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!
XPARTCO EAU63103201 Refrigerator Evaporator Fan Motor
The XPARTCO EAU63103201 is an aftermarket replacement evaporator fan motor for LG and select Kenmore/Kenmore Elite refrigerators. On this platform, the fan sits behind a panel near the crisper drawers and circulates air specifically through the fresh food compartment — a different physical location than the freezer-mounted evaporator fans found on many other brands. When this motor slows down or fails, the fresh food section is the part of the refrigerator most directly affected, since it depends on this fan to keep cold air moving across the compartment.
Rated 12V DC at 1A with a 4-pin connector, this motor has a 2.36" (60mm) shaft length and a 0.12" (3.16mm) shaft diameter, with roughly a 20.5" (56cm) wire lead. Common failure modes include worn motor bearings that let the blade wobble or bind, and general electrical wear from age. A fridge running warm, not cold at all, or making unusual noise from behind the crisper area are all signs pointing to this motor. It directly replaces 4391461, AP6317185, PS11761147, EAP11761147, and PD00051700. Also identified by its production number, ODM-001F-41.
Quick Answer
The XPARTCO EAU63103201 Refrigerator Evaporator Fan Motor fixes LG and select Kenmore/Kenmore Elite refrigerators where the fresh food compartment runs too warm or isn't cooling at all, or there's unusual noise from behind the crisper drawer area. DC 12V, 1A, 4-pin connector, 2.36" (60mm) shaft length, 0.12" (3.16mm) shaft diameter. Replaces 4391461, AP6317185, PS11761147, EAP11761147, PD00051700. LG uses several similarly-numbered EAU-prefix fan motors across its lineup — this is a different part from the EAU63923603/EAU65058305 assembly used on other LG models, so verify your exact model number before ordering.
Common Problems This Part Fixes
Fresh food compartment running too warm
Refrigerator not cooling at all in the fresh food section
Unusual noise coming from behind the crisper drawer area
Fan motor that won't run due to aging or internal damage
Refrigerator running constantly as it struggles to maintain temperature
Fan blade that doesn't spin freely, or spins with noticeable resistance, when checked by hand
Frost or condensation forming near the fan location behind the crisper panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers:
EAU63103201, ODM-001F-41, 4391461, ALG1473540, AP6317185, PS11761147, OEM18086529, EAP11761147, PD00051700
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select LG refrigerators, and also fits select Kenmore and Kenmore Elite refrigerators built on the LG platform, including model numbers such as:
LG LRSES2706V, LRSPS2706V
LG LSXC22396D, LSXC22396S, LSXC22426S, LSXC22436S
LG LSXC22486D, LSXC22486S
LG LSXS26326B, LSXS26326S, LSXS26326W
LG LSXS26336S, LSXS26336V, LSXS26336D
LG LSXS26386S, LSXS26396S
Kenmore 795.5173381, 795.5173781, 795.5183241, 795.5183242, 795.5183341, 795.5183941, 795.5183942, 795.5185361, 795.5185761, 795.5186261, 795.5186361, 795.5186761, 795.5186961
Note: LG uses several different evaporator fan motors across its refrigerator lineup with similar EAU-prefix part numbers. This EAU63103201 motor is a separate, distinct part from the EAU63923603 / EAU65058305 fan motor assembly used on other LG models (such as the LFXS28596S, LMXS28626S, LFXS26596S, and LFXS26973D series) — the two are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs.
Key Features
Aftermarket replacement evaporator fan motor — circulates air through the fresh food compartment
Resolves "fresh food too warm," "not cooling at all," and "noise behind the crisper drawer" symptoms caused by fan motor failure
Rated 12V DC, 1A, with a 4-pin connector for direct plug-and-play electrical fit
2.36" (60mm) shaft length, 0.12" (3.16mm) shaft diameter
Approximately 20.5" (56cm) wire lead
Direct drop-in replacement matching the original mounting and blade fitment
Replaces 4391461, AP6317185, PS11761147, EAP11761147, and PD00051700
Compatible with LG and select Kenmore/Kenmore Elite refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair — just a screwdriver needed on most models
Product Specifications
Part Number
XPEAU63103201
OEM Part Number
EAU63103201 (ODM-001F-41)
Part Type
Refrigerator Evaporator Fan Motor
Condition
Aftermarket Replacement
Compatible Brand
LG, Kenmore
Location
Behind panel near the crisper drawers, fresh food compartment
Voltage
12V DC
Amperage
1 A
Connector
4-pin
Shaft Length
2.36 in. (60mm)
Shaft Diameter
0.12 in. (3.16mm)
Wire Lead Length
Approx. 20.5 in. (56cm)
Color
Gray
Material
Plastic and metal
Quantity
1 fan motor
Compatible Brands
LG, Kenmore, Kenmore Elite
Installation Notes
⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Access on this platform is different from many other brands: rather than removing a rear panel inside the freezer, slide the crisper drawer out fully, then remove the panel behind or above the drawer area to expose the fan motor. Photograph the wiring connector and the fan blade's position before disconnecting anything. Disconnect the 4-pin electrical connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and carefully pull the motor and fan blade assembly free. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation on the 60mm shaft. Mount the new EAU63103201 in the same position, reconnect the 4-pin connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the panel and sliding the crisper drawer back into place. Restore power and monitor the fresh food compartment over the next several hours to confirm normal cooling has returned. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
Why is this fan located near the crisper drawers instead of in the freezer?
LG's refrigerator platform routes cold air to the fresh food compartment differently than many other brands, with this particular fan positioned behind a panel near the crisper drawer area rather than inside the freezer compartment. That's simply a difference in refrigerator design between manufacturers — it doesn't affect the fan's job, which is still to keep cold air circulating through the fresh food section, but it does mean the access point for this repair looks different from what you might expect if you've worked on a different brand before.
My fridge section is warm but everything else seems fine. Is this the right part?
Yes, this is the classic symptom this motor addresses. Since this fan specifically circulates air through the fresh food compartment, a failure here tends to affect that section directly — a warm fridge with an otherwise normally-functioning freezer points squarely at this motor rather than at the compressor or refrigerant system.
There are several similar LG fan motor part numbers online. How do I know I have the right one?
LG's EAU-prefix fan motors can look similar at a glance, but they aren't interchangeable — for example, the EAU63923603/EAU65058305 assembly used on models like the LFXS28596S and LMXS28626S is a completely different part from this EAU63103201 motor. The safest way to confirm is to check your refrigerator's full model number against a verified compatibility list, or contact our support team with your model number before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the electrical specifications (12V DC, 1A, 4-pin connector), shaft dimensions, and mounting configuration of the original EAU63103201 evaporator fan motor used in compatible LG and Kenmore refrigerators.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WD13X10031 Dishwasher Genuine OEM Door Latch
Replaces Part Numbers: WD13X10031, 1088549, AH959002, EA959002, AP3778749, PS959002.
Description: This dishwasher door latch, model WD13X10031, is a genuine OEM part. It ensures a secure and reliable closure of your dishwasher door, preventing any leaks and ensuring effective cleaning. With this product, you can have peace of mind knowing your dishes will be washed efficiently and without any hassle.
XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag
Product Description
Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat.
Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model.
Replaces part numbers:
Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405.
Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325.
Compatibility:
Compatible with select dryer models, including but not limited to:
Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0
Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990
Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW
Roper: RED4440VQ1, REX5634KQ1
Amana: NED4655EW0
KitchenAid: KEYE760WWH0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers.
🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable).
💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying.
🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes.
🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times.
Product Specification
Part Number: XPARTCO 3387134 - 3392519
Component Type: Dryer cycling thermostat and thermal fuse kit
Material: Plastic and metal
Electrical Specs:
Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F
Thermal Fuse: 250°F limit, 125/250V, non-resettable
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today!
Add to cart now for a reliable fix!
XPARTCO 5304528029 Washer Water Valve
Dispenser Valve Gaskets are Not Included
Washer water inlet valve.
5 Solenoid Coils, 5 Outlets
Fits Specific Electrolux, Frigidaire front load washer models.
Replaces Part Numbers:5304528029, 5304514790, 5304522534, AP7014477, PS16544354.
Description: This Water Valve is a replacement part for specific Electrolux, Frigidaire washing machine models. This part controls the entry of water into the washer during the wash and rinse cycles. Common causes of a bad valve include mineral deposits from hard water, electrical issues, or general wear and tear over time.
This is an aftermarket part that can be used as a replacement for the OEM part.
154756401 Genuine Frigidaire Dishwasher Door Hinge Cable
The 154756401 is a Genuine OEM Frigidaire replacement dishwasher door hinge cable compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers. The door hinge cable runs through a pulley system at the base of the dishwasher door and is responsible for balancing and controlling the weight of the door as it opens and closes. When a cable breaks or frays, the door drops down suddenly and heavily, opening with a loud bang — or may not hold itself up at all, straining the door hinges and latch with every use.
This is a Genuine OEM part manufactured by Frigidaire to factory specifications and directly replaces the older 154578801. It is sold as a single cable — most Frigidaire dishwashers have two door hinge cables (one on each side), and it is strongly recommended to replace both at the same time. Installs in under 30 minutes with basic hand tools.
Quick Answer
The 154756401 Genuine Frigidaire Dishwasher Door Hinge Cable fixes dishwashers where the door drops open too fast, bangs loudly when opened, doesn't stay open at a comfortable angle, or where a broken cable is visible at the door hinges. Sold individually — replace both cables at the same time. Compatible with Frigidaire, Electrolux, Kenmore, Crosley, and Ikea dishwashers. Replaces 154578801.
Common Problems This Part Fixes
Dishwasher door drops suddenly and forcefully when opened — "slams" down instead of lowering gently
Loud banging or crashing noise when opening the dishwasher door
Door does not stay open at a horizontal position — drops all the way down
Broken, frayed, or snapped door cable visible near the door hinge or base of the door
Door hinge is being damaged or strained due to missing cable tension
Uneven door opening — one side drops faster than the other
Replaces Part Numbers
This door hinge cable directly replaces the following OEM and cross-reference part numbers:
154756401, 154578801, AFR14437, PD00082115, AP7212793, PS17217958.
154756401 is the current updated part number superseding the older 154578801. Contact our support team with your model number if you need compatibility confirmation before ordering.
Compatibility
This door hinge cable is compatible with select dishwashers from the following brands:
Frigidaire dishwashers
Electrolux dishwashers
Kenmore / Sears dishwashers (Frigidaire/Electrolux-built models)
Crosley dishwashers
Gibson dishwashers
Kelvinator dishwashers
Westinghouse dishwashers
Ikea dishwashers (select models)
Important: Most Frigidaire dishwashers use two door hinge cables — one on each side. This part is sold as a single cable. It is strongly recommended to replace both cables at the same time, as the second cable is likely to fail soon after the first.
Key Features
Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance
Balances and controls door weight as it opens and closes — prevents sudden door drops and hinge damage
Works in conjunction with the door pulley and spring system to provide smooth, controlled door movement
Current updated part number — directly supersedes 154578801
Sold individually — most models require two cables (one per side); replace both at the same time
Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers
DIY repair — installs in under 30 minutes with basic hand tools
Product Specifications
Part Number
154756401
Supersedes
154578801
Part Type
Dishwasher Door Hinge Cable
Condition
Genuine OEM
Application
Dishwashers
Material
Metal cable
Sold As
Single cable (most models require 2 — replace both at the same time)
Compatible Brands
Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, Ikea
Installation Notes
⚠️ Unplug Dishwasher Before Starting Disconnect power before beginning any repair. Open the dishwasher door and remove the inner door panel by unscrewing the screws around the perimeter of the inner door. With the inner panel removed, locate the door hinge cable routing — the cable runs from a bracket near the bottom of the door, through a pulley, and connects to the door spring tension system at the base of the dishwasher. Note how the cable is routed before removing the old one. Remove the broken cable by detaching it from the anchor points at each end. Thread the new 154756401 cable through the same pulley path and re-attach it to the anchor points at both ends, ensuring proper tension. Reinstall the inner door panel. Close and open the door to verify it moves smoothly and holds itself open horizontally. Restore power and run a short cycle to confirm normal operation. Tip: Replace both cables at the same time — the second cable will likely fail soon after the first. Tools needed: Phillips screwdriver, Torx screwdriver (T20), needle-nose pliers.
Frequently Asked Questions
What does the dishwasher door hinge cable do?
The door hinge cable is a tensioned metal cable that runs through a pulley and connects to the door spring system to balance the weight of the dishwasher door as it opens and closes. Without the cable, the full weight of the door would cause it to drop suddenly and forcefully when opened, slamming down onto the floor or straining the hinges with every use. The cable provides the controlled, counterbalanced movement that allows the door to lower gently and stay open at a horizontal position for easy loading and unloading.
How many door cables does my Frigidaire dishwasher have?
Most Frigidaire dishwashers use two door hinge cables — one on the left side and one on the right side of the door. This listing is for a single cable. When one cable breaks, the other is typically close behind since both cables have endured the same amount of use. It is strongly recommended to replace both cables at the same time while the door panel is already disassembled, saving you from repeating the repair shortly after.
What is the difference between 154756401 and 154578801?
These are the same door hinge cable. 154756401 is the current updated part number that superseded the older 154578801 during a production revision. If your dishwasher's parts diagram or old cable label shows 154578801, the 154756401 is the correct current replacement to order.
Is this compatible with Electrolux and Kenmore dishwashers?
Yes — Frigidaire and Electrolux are part of the same corporate family and share many components. The 154756401 cable is compatible with select Electrolux dishwashers and with Kenmore dishwashers built on the Frigidaire/Electrolux platform. Always verify your specific model number before ordering to confirm compatibility.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same door hinge cable installed in compatible Frigidaire, Electrolux, and related brand dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit
The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed.
This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below.
Quick Answer
The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run.
Common Problems This Part Fixes
Dryer door won't stay closed
Door pops open in the middle of a cycle
Dryer won't start because the open-door condition isn't clearing
Worn, cracked, or damaged catch or strike
Heat escaping around the door, leaving clothes damp
Door that no longer latches with a firm, positive click
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door latch kit directly replaces the following part numbers:
5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570
This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts.
Compatibility
This latch kit is used on dryer models from the following brands:
Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers
Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers
GE and Hotpoint dryers
Select LG and Kenmore (LG-built) dryers
Select Crosley, Norge, and Speed Queen dryers
Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch.
Key Features
2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike
Replaces both halves of the latch in one repair
Restores a secure door closure so heat stays in and the dryer runs efficiently
Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start
Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering
2 kits per order (2 door catches and 2 strikes in total)
Product Specifications
Part Number
EXP570 (2 Pack)
OEM Part Number
279570, 5303207102, WE01X10023, 4027EL2001A
Part Type
Dryer Door Latch Kit (Door Catch & Strike)
Condition
Aftermarket Replacement
Kit Contents
1 Door Catch & 1 Strike per Kit
Quantity
2 Kits (2 Door Catches & 2 Strikes)
Application
Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly.
Frequently Asked Questions
My dryer door won't stay shut — is this the part I need?
Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix.
My dryer won't start and seems to think the door is open. Could this be the cause?
It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead.
What's included in the kit?
This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch.
Will this fit my Whirlpool, Frigidaire, GE, or LG dryer?
This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10006355 Washer Shift Actuator
Fits specific Maytag, Kenmore, Whirlpool top-load machine models.
Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977.
Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor Replaces WP8557403
The XPARTCO 8557403 is an aftermarket replacement dryer high-limit thermostat and thermistor sensor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers — including the Whirlpool Duet and Maytag MED series. This single component combines two functions: the high-limit thermostat (rated L146-44C, opens at 295°F) acts as a resettable safety switch that cuts power to the heating element if the dryer air temperature exceeds safe limits, and the integrated 50-ohm thermistor continuously monitors air temperature and sends resistance-based readings to the control board to regulate the drying cycle.
When this part fails — whether the thermostat opens permanently or the thermistor provides incorrect temperature data — the dryer may produce no heat, run too hot, take too long to dry, overheat, or display temperature-related error codes. It measures 1-5/8"L x 1-5/8"W x 2"H with approximately 1-5/8" between mounting holes and is constructed from black/gray plastic and metal. It directly replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386. Note: the exhaust duct thermostat and thermal fuse are separate parts — if those have also failed, they must be ordered separately. Installs in 15–20 minutes with basic hand tools.
Quick Answer
The XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor fixes Whirlpool Duet, Maytag MED, and related dryers with no heat, overheating, or erratic temperature. Combined part: L146-44C high-limit thermostat (opens at 295°F, auto-resets) + 50-ohm NTC thermistor. 1-5/8"L x 1-5/8"W x 2"H, ~1-5/8" between mounting holes. Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, PS11746386. For Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, and Admiral electric dryers.
Common Problems This Part Fixes
Dryer produces no heat — high-limit thermostat has failed open
Dryer overheating — thermostat not opening at the correct temperature
Dryer takes too long to dry — thermistor providing incorrect temperature readings to the control board
Dryer cycling on and off erratically — thermistor fault causing incorrect cycle control
Temperature-related error codes on models with digital displays
Multimeter test shows open circuit on the thermostat at room temperature
Multimeter test shows open or shorted thermistor (not ~50 ohms at room temperature)
Replaces Part Numbers
This thermostat/thermistor assembly directly replaces the following OEM and cross-reference part numbers:
WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This high-limit thermostat and thermistor is compatible with select electric dryers only from the following brands:
Whirlpool electric dryers — Duet, WED5000, WED5500, WED5600, WED5620, WED8000, WED8200, WED8500, WED9200, WED92HEF, WED7000 series and related models
Maytag electric dryers — MED3500, MED5630, MED6630, MED7230, MEDB835 series and related models
Kenmore / Sears electric dryers — 110-series (Whirlpool-built models)
Amana electric dryers (select models)
KitchenAid electric dryers (select models)
Jenn-Air electric dryers (select models)
Roper electric dryers
Admiral electric dryers
Norge electric dryers
Magic Chef electric dryers
Note: This part is for electric dryers only. The exhaust duct thermal fuse and cycling thermostat are separate parts — if those have also failed, they must be ordered separately. Always verify your model number before ordering.
Key Features
Combined high-limit thermostat and thermistor in a single assembly — replaces both functions in one part
High-limit thermostat rated L146-44C — opens at 295°F (146°C), resets automatically when cooled
Integrated 50-ohm NTC thermistor — continuously monitors dryer air temperature and sends readings to the control board for cycle regulation
Dimensions: 1-5/8"L x 1-5/8"W x 2"H; approx. 1-5/8" between mounting holes
Black/gray plastic and metal construction
Electric dryers only — not for gas dryer models
Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386
Compatible with Whirlpool Duet, Maytag MED, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–20 minutes with basic hand tools
Product Specifications
Part Number
8557403
OEM Part Number
WP8557403
Part Type
Dryer High-Limit Thermostat with Integrated Thermistor Sensor
Condition
Aftermarket Replacement
Application
Electric Dryers Only
Thermostat Rating
L146-44C — opens at 295°F (146°C), auto-resets
Thermistor
50-ohm NTC (at room temperature ~25°C)
Dimensions
1-5/8"L x 1-5/8"W x 2"H
Mounting Hole Spacing
Approx. 1-5/8" center to center
Color
Black / Gray
Material
Plastic / Metal
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. The 8557403 thermostat/thermistor assembly is typically located on the heating element housing or duct inside the dryer — access it by removing the back panel. On Whirlpool Duet and Maytag front-load-style dryers, the component may be accessible by removing the lower front panel. Photograph all wire connections before disconnecting — the thermistor wires and thermostat wires must be reconnected to the correct terminals. Remove the two mounting screws and pull the old assembly off. Note the position and orientation before removing. Install the new 8557403 assembly in the same position and orientation, reconnect all wires, and reinstall the mounting screws and panel. Restore power and run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver.
Frequently Asked Questions
What makes this part unusual — why does it combine a thermostat and a thermistor?
The WP8557403 is a combined assembly used on newer Whirlpool Duet and Maytag MED series dryers that use electronic temperature control rather than purely mechanical thermostats. The high-limit thermostat (L146-44C) provides the traditional safety function — it opens the circuit if dryer temperature exceeds 295°F. The integrated NTC thermistor continuously reports resistance-based temperature data to the electronic control board, which uses the data to regulate the heating element and control cycle timing. Both functions are built into a single compact housing, making this a unique part that replaces what older dryers used to handle with separate components.
How do I test the thermostat and thermistor?
Set your multimeter to continuity or resistance mode. For the thermostat portion: probe the thermostat terminals — at room temperature, a working thermostat shows closed continuity (near-zero resistance). An open circuit at room temperature confirms the thermostat has failed. For the thermistor portion: probe the thermistor terminals — at room temperature (approximately 25°C/77°F), a working 50-ohm NTC thermistor should read approximately 50 ohms. A reading of zero ohms (shorted) or open circuit (no continuity) confirms the thermistor has failed. Either failure mode warrants replacing the complete 8557403 assembly.
What is the difference between 8557403 and WP8557403?
These are the same part. WP8557403 is the updated Whirlpool OEM part number that superseded the original 8557403. The 1180102 is also a cross-reference for this same assembly. This aftermarket replacement is compatible with all of these numbers.
Do I also need to replace the thermal fuse or cycling thermostat?
The 8557403 replaces the high-limit thermostat and thermistor mounted on the heating element housing area. The exhaust duct thermal fuse (WP3392519 on most Whirlpool-family dryers) and cycling thermostat (WP3387134) are separate components located on the exhaust duct and are not included in or replaced by the 8557403. If your dryer has no heat, test all thermal components before ordering — check the 8557403 assembly, the thermal fuse, and the cycling thermostat, then order only what has failed. If an overheating event caused the high-limit to fail, the other thermal components may be stressed as well.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal with an L146-44C thermostat and 50-ohm NTC thermistor to match the specifications and performance of the original WP8557403 assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WP3387134 Dryer Cycling Thermostat
The Genuine OEM Whirlpool WP3387134 is a dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F.
When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is the original Whirlpool part, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names.
Quick Answer
The Genuine OEM WP3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent.
Common Problems This Part Fixes
Dryer not heating
Dryer running too hot
Inconsistent drying temperatures
Heat staying on after the drum has stopped
Dryer won't start or the timer doesn't advance, if the thermostat has failed
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This cycling thermostat directly replaces the following part numbers:
WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187, EAP11741405, WP3387134VP, AP6008270, AWP47432, EAP11741405, PD00002313, PS11741405, L155-25F
These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram.
Compatibility
This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples:
Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990
Numerous additional Whirlpool-built dryer models
Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool cycling thermostat
Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop
Keeps dryer temperature steady by cycling the heating element on and off
Resolves no-heat, overheating, and inconsistent-temperature symptoms
Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers
Medium-difficulty repair with basic hand tools
Product Specifications
Part Number
WP3387134
OEM Part Number
WP3387134
Part Type
Dryer Cycling Thermostat
Condition
Genuine OEM
Temperature Rating
L155-25 (Cuts Out ~155°F, 25°F Differential)
Application
Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating.
Frequently Asked Questions
My dryer isn't heating or runs too hot. Is this the part I need?
A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it.
What's the difference between the cycling thermostat and the high limit thermostat?
The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only.
How do I test this thermostat?
With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed.
Will this fit my dryer?
It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
