Search results for "Tub Seals"

WH41X22935 Washer Tub to Pump Hose Washer Tub to Pump Hose Replaces Part Number: WH41X22935, WH41X10163, 123C7981, 4258948, J27-763, WH41X0371, WH41X371, AP5983873, PS11721808. Description: This Washer Tub to Pump Hose is a replacement part for select GE, Hotpoint Top-Load Washer models.  This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W11168740 Washer Genuine OEM Cold Water Inlet Valve The W11168740 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, KitchenAid, Amana, and related models. Located at the rear of the washer, this valve connects to the cold water supply and solenoid wiring, opening to admit cold water into the tub as the cycle calls for it and closing once the correct fill level is reached. Blue in color, with two solenoids, a standard hose fitting inlet, and a single water outlet. Common causes of failure include a worn internal seal that no longer closes fully, or general electrical wear in the solenoid. Symptoms of a failing valve include the washer not getting any cold water, filling slowly, not filling at all, or continuing to fill or leak water even after the washer has been unplugged. It directly replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073. Quick Answer The W11168740 Washer Genuine OEM Cold Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, KitchenAid, and Amana top-load washers that aren't getting cold water, are filling slowly, aren't filling at all, or keep leaking or filling even when unplugged. Blue, two solenoids. Replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073. If water keeps running even after the washer is unplugged, try shutting off the cold water supply valve — if that stops it, the cold water inlet valve isn't closing properly and needs replacing. Common Problems This Part Fixes Washer not getting any cold water Washer filling slowly Washer not filling at all Water continuing to fill or leak even after the washer is unplugged Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168740, WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, KitchenAid, and Amana washers built on the Whirlpool platform. Note: This is the cold water valve only — a separate hot water valve is used alongside it on the same washer. If your washer isn't getting hot water rather than cold, you likely need the companion hot water valve instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates cold water flow into the washer tub during fill Resolves "no cold water," "fills slowly," "won't fill," and "leaks or fills when unplugged" symptoms Blue color with two solenoids Standard hose fitting inlet, single water outlet Direct drop-in replacement — matches the original mounting and hose connections Replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, and Amana top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically 20 to 30 minutes Product Specifications Part Number W11168740 Part Type Washer Cold Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Rear of the appliance Color Blue Solenoids 2 Inlet Standard hose fitting Outlet 1 Repair Difficulty Easy — 20 to 30 minutes Quantity 1 valve (sold individually) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access is at the rear of the washer, where both the cold and hot water inlet valves are typically mounted together, each secured with just a few screws. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical clamps and the water hose from the old cold water valve, remove the mounting screws, and pull it free. Install the new W11168740 in the same position, reconnect the water hose and electrical clamps fully, and secure the mounting screws. While you're in this area, consider replacing the fill hose at the same time if it shows signs of wear, since it's easy to access during this same repair. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Water keeps running even after I unplug my washer. Is this the valve I need? Yes, this is a documented symptom of a cold water inlet valve that's no longer closing properly. One customer had exactly this experience — after unplugging the washer, water continued to run, and shutting off the cold water supply valve at the wall stopped it. That confirmed the cold water inlet valve itself wasn't sealing shut, even with no power to the washer, and replacing it resolved the issue. Should I replace the hot water valve at the same time? It's worth considering, especially if both valves are the same age. Several customers have replaced both the hot and cold valves together in a single repair, since they're mounted in the same area and access is already open — one customer described it as "very quick & easy" to do both at once. Is this a difficult repair? No, this is a straightforward repair. Multiple customers describe it as easy, typically secured with just a few screws and simple electrical clamp connections — one review specifically noted the whole job took about 20 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the cold water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X26637 Washer Water Valve The XPARTCO WH13X26637 is an aftermarket replacement quad water inlet valve for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models. This valve controls the flow of water into the washer from the household supply line, using two internal valves — each with its own wire terminals — to manage water flow and temperature blending for the wash cycle. When the control calls for a fill, the corresponding solenoid opens to admit water and closes once the correct level is reached. Rated 120V, 6/5W. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve produces a clear set of symptoms: the washer not starting, an error code related to water fill, or — one of the most common complaints — water continuing to drip into the tub between cycles even when the washer isn't running, since a worn internal seal can fail to shut off completely. It directly replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665. Quick Answer The XPARTCO WH13X26637 Washer Water Valve fixes GE top-load washers (and select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models) that won't start, show a water-fill error code, or have water dripping into the tub between cycles. Quad valve design — 2 valves, each with its own wire terminals. 120V, 6/5W. Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, PD00037665. Dripping into the tub between cycles, even with the washer off, is a classic sign of a worn valve seal that isn't shutting off completely. Common Problems This Part Fixes Washer won't start Error code related to water fill displayed on the control panel Water dripping into the tub between cycles, even when the washer isn't running Washer filling slowly or only partially No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, 4546358, AGE26282, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X24058, WH13X26637-25PK, PD00037665 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore washers built on the GE platform, including model numbers such as: GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS GTW685BPL0DG, GTW750CPL1DG, GTW720BSN0WS PTW605BPR1DG, PTW605BSR0WS, PTW605BSR1WS PTW700BPT0DG, PTW700BST0RS, PTW700BST0WS PTW705BPT0DG, PTW705BST0RS, PTW705BST0WS Note: This is a top-load washer valve, distinct from GE's front-load valves used on other GE washer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement quad water inlet valve — two valves, each with its own wire terminals Resolves "won't start," "water fill error code," and "dripping into the tub between cycles" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Rated 120V, 6/5W Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665 Compatible with GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair, typically 15 to 30 minutes Product Specifications Part Number XPWH13X26637 OEM Part Number WH13X26637 Part Type Washer Quad Water Inlet Valve Condition Aftermarket Replacement Application Top-Load Washers Voltage 120V Wattage 6/5 W Valve Design Quad — 2 valves, each with separate wire terminals Repair Difficulty Easy — 15 to 30 minutes Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, RCA, Café, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves at the wall before beginning. Wear work gloves. Unscrew the hot and cold supply lines from the bottom of the old valve, then carefully pull the valve assembly away from the wall for access. Photograph the wiring and hose connections before disconnecting anything, since this valve has two separate wire terminal sets and multiple outlet hoses. Remove the cover securing the valve in place, disconnect the electrical connectors and outlet hoses, and take out the old valve — the entire assembly typically comes out in one piece. Insert the new WH13X26637 into the same opening, making sure it fits tightly and securely, and secure it with screws. Reconnect all outlet hoses to their original positions, reconnect the electrical connectors fully, and put the cover back on. Reconnect the hot and cold supply lines, tightening securely. Turn the water supply back on and check for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: screwdriver, spanner, pliers or adjustable wrench, work gloves. Frequently Asked Questions Water keeps dripping into my washer tub even when it's not running. Is this the valve? Yes, this is one of the most common symptoms of a failing valve, and a well-documented one for this exact part. If you've already checked the hoses and confirmed they're not the source of the leak, a worn internal seal in the valve is the most likely remaining cause — the seal fails to shut off completely, letting a small amount of water continue dripping through even between cycles. Shutting off the water supply is a temporary workaround, but replacing the valve is the permanent fix. Why does this valve have two sets of wire terminals? This is a quad valve design, meaning it houses two separate internal valves in one assembly, each with its own electrical connection. This allows the washer to independently control different water functions — such as hot and cold fill — from a single combined unit rather than requiring two completely separate valve housings. Is this a top-load or front-load washer valve? This is a top-load washer valve, compatible with GE's GTW and PTW model series. It's a different valve design from the ones used on GE's front-load washer platforms, so confirm your washer type and model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the quad valve design, wattage, and connection type of the original WH13X26637 valve used in compatible GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Frigidaire OEM Frigidaire 5304533220 Washer Water Fill Hose Assembly Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units. Product Overview The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models. This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets. Quick Answer 5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers. Common Problems This Part May Fix Water leaking inside the washer cabinet during fill Cracked, split, hardened, or deteriorated fill hose Leak between the inlet-valve outlet and wash tub Loose or damaged internal water-fill connection Water dripping from the valve-to-tub hose during operation Replaces and Cross-References 5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853 Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering. Compatibility Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as: FLCE7523AW0 FLCE7523AW1 FLCE7522AW1 FLCE7522AW4 FFLE3900UW0 FFLE3900UW1 FFLG3900UW0 FFLE3911QW1 CFLE3900UW0 41761712511 41761732810 41771732810 Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase. Key Features Genuine Frigidaire OEM replacement part Internal valve-to-tub fill hose Routes fill water from the inlet valve to the washer tub Direct replacement for 5304508358 and 809191901 Factory-style fit for compatible laundry centers Used on select Frigidaire, Kenmore, and related Electrolux-built models Product Specifications Manufacturer Part Number 5304533220 Brand Frigidaire Part Type Washer Internal Water Fill Hose Hose Location Water Inlet Valve to Wash Tub OEM Status Genuine OEM Appliance Type Laundry Center / Washer-Dryer Combo Condition New External Supply Hose? No — this is an internal appliance hose Installation Notes Disconnect electrical power to the appliance before service. Shut off both household water-supply valves. Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure. Place towels or a shallow pan below the hose connections to catch residual water. Release the clamps and remove the old hose without damaging the valve outlet or tub fitting. Install the new hose fully onto both fittings and reinstall the clamps in their original positions. Restore water and inspect carefully for leaks before returning the appliance to service. Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part. Frequently Asked Questions Is 5304533220 a Genuine OEM part? Yes. It is a Genuine Frigidaire OEM fill hose. Does 5304533220 replace 5304508358? Yes. 5304533220 supersedes 5304508358 and 809191901. Is this the hose that connects the washer to the wall faucet? No. This is an internal valve-to-tub fill hose located inside the laundry center. Can this part correct a washer leak? Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering. Shop With Confidence Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose. Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping

Read more less

3204405 Washer Outer Tub Bearing Replaces: 3204405, 508644, AH446536, EA446536, AP2131587, PS446536. 3204405 Washer Outer Tub Bearing – Genuine OEM Replacement Fix noisy or unbalanced wash cycles with the 3204405 Outer Tub Bearing. This Genuine OEM part supports the washer drum and allows smooth, quiet rotation during cycles. Key Features: ✅ Genuine OEM Part – designed for reliable, long-lasting performance 🔁 Replaces: 3204405, 508644, AH446536, EA446536, AP2131587, PS446536. 🌀 Ensures smooth drum movement and reduces vibration 🛠️ Fits select Frigidaire, Gibson, Kenmore, Westinghouse washers 🧰 Essential for tub and spin basket support ⚠️ Washer must be disassembled for bearing replacement. Contact us to confirm compatibility. 📦 Part Number: 3204405💯 30-Day Money Back Guarantee

Read more less

WH13X26637 Genuine OEM GE Washer Water Inlet Valve The WH13X26637 is a Genuine OEM GE replacement quad water inlet valve assembly compatible with select GE and GE Profile top-load washers in the GTW, GTV, GTN, PTW, and related series. This is a quad (4-solenoid) valve assembly that controls the flow of hot water, cold water, bleach dispenser water, and fabric softener dispenser water from the household supply lines into the washer tub and dispenser compartments. Each solenoid port is independently controlled by the washer's control board. When any port fails, the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or drip water between cycles. As a Genuine OEM part manufactured by GE to factory specifications, the WH13X26637 is a direct current-production replacement for the earlier WH13X24058. It measures approximately 7"L x 3"W x 3"H with multi-colored ports (blue, green, red, tan, silver, and gold) for easy identification of each solenoid's function. It directly replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PD00037665, and PS12171559. Installs in 20–30 minutes with basic hand tools. Quick Answer The WH13X26637 Genuine OEM GE Washer Water Inlet Valve fixes GE top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or drip water between cycles. Quad (4-solenoid) valve. Approx. 7"L x 3"W x 3"H. Multi-color port identification. Genuine OEM. Replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PS12171559. Compatible with GE GTW, GTV, GTN, PTW series top-load washers. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more solenoid ports partially blocked or failing Washer filling with only cold or only hot water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach not dispensing during the wash cycle Fabric softener not dispensing at the rinse cycle point Water dripping into the tub between cycles — valve port not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, WH13X24058, AGE26282, AP6282070, EAP12171559, PD00037665, PS12171559. WH13X26637 is the current updated part number superseding WH13X24058. If your washer's parts diagram shows WH13X24058, the WH13X26637 is the correct current replacement. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select GE and GE Profile top-load washers from the following series: GE washers — GTW680 series (GTW680BPL0DG, GTW680BPL1DG, GTW680BPL2DG, GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS and related models) GE washers — GTW685 series (GTW685BPL0DG, GTW685BPL1DG, GTW685BSL1WS, GTV685BSL0WS and related models) GE washers — GTW720 series (GTW720BPN0DG, GTW720BSN0WS and related models) GE washers — GTW725 series (GTW725BPN0DG, GTW725BSN0WS and related models) GE washers — GTW750 series (GTW750CPL0DG, GTW750CPL1DG, GTW750CSL0DG, GTW750CSL0WS, GTW750CSL1WS and related models) GE washers — GTW755 series (GTW755CPM0DG, GTW755CSM0WS, GTW755CSM1WS and related models) GE Profile washers — PTW600, PTW605, PTW700, PTW705 series and related models GE washers — GTN755 series (GTN755CPM1DG and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Quad (4-solenoid) valve assembly — independently controls hot water, cold water, bleach dispenser, and fabric softener dispenser ports Multi-colored ports for easy solenoid identification during installation Dimensions: approximately 7"L x 3"W x 3"H Current updated part number — directly supersedes WH13X24058 Compatible with GE GTW680, GTW685, GTW720, GTW725, GTW750, GTW755, PTW600, PTW605, PTW700, PTW705, GTN755 series top-load washers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH13X26637 Supersedes WH13X24058 Part Type Washer Water Inlet Valve Assembly (Quad / 4-Solenoid) Condition Genuine OEM Application GE and GE Profile Top-Load Washers Solenoids 4 (hot, cold, bleach, fabric softener) Dimensions Approximately 7"L x 3"W x 3"H Port Colors Multi-color (blue, green, red, tan, silver, gold) Material Plastic / Metal Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel and remove it to expose the valve assembly. Photograph all wire harness connections and hose routing — the multi-color ports make this straightforward. Disconnect the two external supply hoses from the hot and cold inlet ports. Disconnect the internal outlet hoses by releasing the retaining clips. Disconnect the wire harness connectors from each solenoid terminal. Unscrew the mounting bolts and remove the old valve. Install the new WH13X26637 valve in the same position, reconnect all hoses and wire harnesses in the documented positions, and secure the mounting bolts. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, socket wrench, needle-nose pliers. Frequently Asked Questions What is the difference between WH13X26637 and WH13X24058? These are the same quad water inlet valve assembly — WH13X26637 is the current updated part number that GE issued to supersede the earlier WH13X24058. If your washer's documentation, parts diagram, or old valve label shows WH13X24058, the WH13X26637 is the correct current replacement to order. Both are quad (4-solenoid) valve assemblies with the same port configuration and function. What does each solenoid port on this quad valve control? The WH13X26637 quad valve has four independently operated solenoid ports. The hot water port opens to supply hot water from the household supply line. The cold water port supplies cold water. The bleach dispenser port delivers cold water through the bleach compartment at the appropriate point in the wash cycle. The fabric softener port delivers water through the softener compartment during the rinse cycle. When any single solenoid fails, only the function it controls is affected — the rest of the valve continues to work normally. My washer won't fill and shows an error code — is it the water inlet valve? A fill error code on compatible GE models commonly points to the water inlet valve. Before replacing the valve, confirm that both supply valves behind the washer are fully open, neither supply hose is kinked, and the household water pressure is adequate. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed and the valve needs replacement. If all coils test good but the washer still won't fill, the issue may be with the control board or water pressure. My washer fills fine but won't dispense fabric softener — could it be the valve? Yes — if only the fabric softener dispenser function is affected, the solenoid coil controlling that specific port has likely failed. Since it is part of the same quad valve assembly, replacing the entire WH13X26637 assembly resolves the failed port. Individual solenoid ports cannot be replaced — the complete quad valve assembly must be replaced when any port fails. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same quad water inlet valve assembly installed in compatible GE and GE Profile top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X10014 Washer Water Inlet Valve The XPARTCO WH13X10014 is an aftermarket replacement water inlet valve for GE washer/dryer combination units — a single cabinet that houses both wash and dry functions and shares one door, lid, and control system for both. This valve sits at the point where the hot and cold water supply lines connect, and it's the gatekeeper for every drop of water that enters the tub during the wash portion of a cycle. When the control calls for a fill, the valve's solenoid opens to admit water; once the correct level is reached, it closes again. Common causes of failure include mineral or sediment buildup inside the valve body that prevents it from sealing fully, and a burned-out internal solenoid coil. A failing valve on a combo unit produces the same core symptoms you'd see on a standalone washer: the wash side won't fill, fills too slowly, won't stop filling, or leaks after the cycle ends — but because a combo unit shares more components in a single cabinet than separate machines do, it's worth confirming the water issue is isolated to the valve and not connected to other combo-specific parts nearby, such as our WH12X955 lid switch listing, which serves this same GE combo platform. It directly replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040. Quick Answer The XPARTCO WH13X10014 Washer Water Inlet Valve fixes GE washer/dryer combo units that won't fill with water, fill slowly, won't stop filling, or leak after the cycle ends. For GE's combination washer/dryer platform (WSM2420/WSM2480 series). Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, 944040. This valve is specific to GE's washer/dryer combo unit — not a standalone front-load or top-load washer valve. Common Problems This Part Fixes Washer/dryer combo won't fill with water at the start of the wash cycle Water fills much more slowly than normal Unit won't stop filling — water continues past the normal level Water leaking or dripping after the cycle has ended Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Unit not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X10014, WH13X0084, WH13X10013, WH13X84, AP3203931, 944040, AH756629, EA756629, AGE844170, PD00066092, PS756629 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select GE washer/dryer combination units, including model numbers such as: GE WSM2420D0WW, WSM2420D1WW, WSM2420D2WW, WSM2420D3WW, WSM2420D4WW, WSM2420D5WW GE WSM2420D0CC, WSM2420D1CC, WSM2420D2CC GE WSM2420TAAWW, WSM2420TBAWW, WSM2420TCAWW, WSM2420TAAAA, WSM2420TAACC, WSM2420TBAAA GE WSM2420SAZAA, WSM2420SBZAA, WSM2420SBZWW, WSM2420SCZAA, WSM2420SCZWW, WSM2420SDZWW GE WSM2480D0WW, WSM2480D1WW, WSM2480D2WW, WSM2480D3WW GE WSM2480SAZAA, WSM2480SAZWW, WSM2480SBZAA, WSM2480SBZWW, WSM2480SEZAA, WSM2480TCAWW Note: This valve is built specifically for GE's washer/dryer combination units. It is not the same valve used on GE's standalone front-load washers (such as our WH13X10029 listing) and is not interchangeable with them. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combination units Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure Solenoid-actuated design opens and closes precisely on the control's signal Direct drop-in replacement — matches the original mounting and hose connections Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040 Compatible with GE washer/dryer combo units, including WSM2420 and WSM2480 series Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number WH13X10014 OEM Part Number WH13X10014 Part Type Washer Water Inlet Valve Condition Aftermarket Replacement Application GE Washer/Dryer Combination Units Actuation Solenoid-operated Connections Hot and cold water supply inlets Quantity 1 valve Compatible Brand GE Installation Notes ⚠️ Shut Off Water Supply And Unplug Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. On these combination units, the top of the cabinet often lifts off or opens as a single enclosure covering both the wash and dry sections, which also carries the lid switch wiring — note this connector's location before pulling the panel free. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove its mounting screws, and pull it free. Install the new WH13X10014 in the same position, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold water supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet enclosure, reconnecting the lid switch harness if it was disturbed, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the wash side fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions Is this the same valve used on a standalone GE washer? No. This valve is built specifically for GE's washer/dryer combination units, which share a single cabinet and control system for both wash and dry functions. GE's standalone front-load washers use a different valve (such as our WH13X10029 listing), and the two are not interchangeable. Always confirm whether your appliance is a combo unit or a standalone washer before ordering. My unit won't stop filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve. A worn internal seal can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only hot or only cold water isn't coming in. Do I need the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold or serviced as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, connection type, and mounting configuration of the original WH13X10014 valve used in compatible GE washer/dryer combination units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137221600 Washer Drain Pump The XPARTCO 137221600 is an aftermarket replacement washer drain pump compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers — including popular Affinity series and washer-dryer combo models. The drain pump is mounted at the base of the washer and is responsible for evacuating the wash and rinse water from the tub through the drain hose at the end of each cycle. When the drain pump fails, the washer can't drain — leaving clothes soaking wet, water pooling in the tub, and the wash cycle unable to advance to spin. Common failure symptoms include humming without pumping (blocked or seized impeller), leaks from the pump housing, loud grinding or clicking noises, and complete pump silence when a drain cycle should be running. Rated 120V AC, 60Hz, 85W, 1.25A. Based on the Askol M65 design, with a firmly attached red flapper to prevent drain backflow into the tub. Constructed from strong, durable plastic to resist cracking and leaking through many years of cycling. Package includes the drain pump, mounting base, and mounting screw. This part directly replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, and PS7783938. Important: before installing the new pump, clean any lint or debris from the rubber boot, verify the drain hose is clear and properly fastened, and check the pump filter for blockage — installing a new pump on a system with the underlying blockage will not resolve the drainage problem. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 137221600 Washer Drain Pump fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers that won't drain, leave clothes soaking wet, are noisy or humming during the drain cycle, or display an E11 error code. 120V AC, 60Hz, 85W, 1.25A. Askol M65 design with red backflow flapper. Kit includes pump + mounting base + screw. Replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, PS7783938. Common Problems This Part Fixes Washer not draining — pump failed to remove water at the end of the wash or rinse cycle Clothes left soaking wet at the end of the cycle — no drain, so no spin can start Water leaking from the bottom of the washer — cracked pump housing or failed seal Loud humming noise but no water flowing — pump motor running against a seized impeller or blockage Grinding, clicking, or unusual noises during the drain cycle E11 error code displayed on the control panel (drain fault) Washer pumps but won't spin — drain cycle can't complete, blocking spin Cycles taking much longer than normal as the washer tries to drain Pump silent during drain — motor windings open or electrical fault Impeller broken, cracked, or missing pieces after opening the pump Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 137221600, 131724000, 134051200, 134740500, 137108100, 137151800, 137151800KITK, 2754548, TJ137108100, ER137108100, PD00000118, EAP7783938, BPX401-72J, AFR14249, AP5684706, PS7783938, Also replaces GE WH23X10041, 2119312, WH23X10009, WH23X10017, WH23X10031, WH23X10034, AH3502779, EA3502779, AP5324214, PS3502779. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers and washer-dryer combos from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW3, FAFW3801LW3 and related), FEX831FS2/FS4, FTF2140ES1, FWS445RFS2, FWX445RFS3 series Frigidaire front-load washers — ATF6000ES1, ATF8000FS1, ATFB6700FS0 series Frigidaire front-load washers — GLTF2940ES3, GLTF2940FS1 and related GLTF series Frigidaire washer-dryer combos — CWS3600AS1 and related Electrolux front-load washers — select models Crosley front-load washers — select models Gibson front-load washers — select models Kelvinator front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built models (41744052400, 41744052401, 41744052500, 41744082500, 41748102700, 41748106700, 41748116700, 41790812995 and related 417-series) Tappan front-load washers — select models Westinghouse front-load washers — select models Note: The redesigned 137221600 may look slightly different from your original (e.g., white or gray housing vs. original black), but functions identically. Ensure proper orientation and flapper alignment during installation. Always verify your appliance model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Drain pump — removes water from the washer tub through the drain hose at the end of the wash and rinse cycles Resolves "won't drain," "won't spin," "wet clothes," "E11 error," and "humming pump" symptoms 120V AC, 60Hz, 85W, 1.25A — correct electrical specifications for compatible Frigidaire-platform washers Askol M65 design with red backflow flapper to prevent water from flowing back into the tub Strong, durable plastic construction resistant to cracking and leaking Kit includes: 1x drain pump, 1x mounting base, 1x mounting screw Replaces 15+ OEM and cross-reference part numbers including 137108100, 137151800, 131724000, 134051200, 134740500, 134740800, AP5684706, and PS7783938 Compatible with Frigidaire (Affinity, FEX, FTF, FWS, FWX, ATF, ATFB, GLTF, CWS series), Electrolux, Crosley, Gibson, Kelvinator, Kenmore (417-series), Tappan, and Westinghouse front-load washers and washer-dryer combos DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP137221600 Part Type Washer Drain Pump Condition Aftermarket Replacement Application Front-Load Washers and Washer-Dryer Combos (Frigidaire/Electrolux platform) Voltage 120V AC Frequency 60 Hz Wattage 85W Amperage 1.25A Design Askol M65 with red backflow flapper Material Durable plastic Includes 1x Drain Pump, 1x Mounting Base, 1x Mounting Screw Error Codes Resolved E11 (drain fault) Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Check for Blockage First Disconnect power at the outlet or breaker and shut off both water supplies at the wall before beginning. Wear work gloves to protect your hands — pump components can have sharp edges. Have towels ready — residual water remains in the pump housing and hoses. Important: before replacing the pump, check for the underlying cause of the drain problem. Inspect the pump filter (accessible on many models via the lower front kick panel), the drain hose for kinks, and the rubber boot at the bottom of the tub for lint, coins, buttons, or other debris — installing a new pump on a system with an unresolved blockage will not fix the drain problem. Remove the appropriate access panel (typically the rear or front lower kick panel — model-dependent) to expose the pump. Photograph the wire harness and hose connections before disconnecting. Disconnect the electrical wire connectors from the pump motor. Squeeze the hose clamps with pliers and slide them back to release the tub-to-pump hose and the pump-to-drain-hose from the pump. Remove the 2 mounting screws holding the pump to its base and lift the old pump out. Clean any residual debris from the rubber boot, hoses, and pump filter area. Install the new 137221600 pump using the included mounting base and screw. Reconnect the hoses with the clamps, orient the red backflow flapper correctly, and reconnect the electrical connectors. Reinstall the access panel, restore water and power, and run a rinse cycle to test drainage and check for leaks at all connections. Tools needed: Phillips screwdriver, needle-nose pliers, channel-lock pliers, small flathead screwdriver, towel, work gloves. Frequently Asked Questions My washer won't drain — is it always the pump? Not always. Before replacing the pump, check for these common causes: 1) Clogged pump filter — most Frigidaire front-load washers have a filter accessible via the lower front kick panel; coins, buttons, lint, and small items can block it. 2) Kinked or clogged drain hose — inspect the entire drain hose from the pump to the wall standpipe or sink. 3) Blocked rubber boot — small items can get stuck between the tub and the pump inlet. 4) Failed lid lock/door switch — if the washer doesn't detect a locked door, it won't run the drain cycle. If all of these check out and the pump still isn't draining (or is humming without moving water), the pump has failed and this is the correct repair. What is the E11 error code on my Frigidaire washer? E11 on Frigidaire and Electrolux front-load washers indicates a drain fault — the control board is not detecting successful drainage within the expected time. Common causes are a failed drain pump, a clogged pump filter, a kinked or clogged drain hose, or debris blocking the impeller. If you've verified the filter and hose are clear but the code persists, replacing the 137221600 drain pump typically resolves it. If the code returns after replacement, check the wire harness between the pump and the control board. Does the pump come with everything I need for installation? Yes — the 137221600 (OE) package includes the drain pump itself, a mounting base, and a mounting screw. This is everything you need for the pump replacement itself. However, you should reuse the original hose clamps and hoses from your old pump (they should still be in good condition). If you find that the rubber boot at the base of the tub is cracked, hardened, or torn during the repair, that's a separate part that would need to be ordered — inspect it before completing the reinstallation. The new pump looks different from my old one — is it the right part? Very likely, yes. The 137221600 has been through several revisions over its production history — some housings are black, others white or gray, and the exact shape can vary slightly across production runs. As long as the mounting bolt pattern, hose inlet/outlet sizes, and electrical connector are the same, and the specs match (120V, 60Hz, 85W, Askol M65 design), the pump will function identically to your original. During installation, focus on correct orientation and flapper alignment — the flapper (red) must be positioned so it opens outward toward the drain hose direction to prevent backflow. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (120V AC, 60Hz, 85W, 1.25A), Askol M65 design, red backflow flapper, dimensions, and drain pump function of the original 137221600 used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

2159083 Genuine OEM Whirlpool Refrigerator Door Gasket The 2159083 is a genuine Whirlpool OEM door gasket for the fresh food (refrigerator) door on Whirlpool side-by-side refrigerators. This flexible rubber gasket runs around the entire inner edge of the door and is what actually creates the airtight seal against the cabinet when the door closes — magnetic strips embedded inside the gasket pull it snug against the frame, keeping cold air inside and warm room air out. It's a simple-looking part with an outsized job: nearly every "why is my fridge working overtime" complaint traces back either to the gasket or to something the gasket is failing to seal against. Black in color, measuring approximately 19-1/4" wide by 62" tall. Over time, the gasket's rubber loses flexibility and can crack, tear, or develop permanent creases, and its embedded magnetic strip can weaken. Food debris or moisture trapped along the sealing edge accelerates this wear. A failing gasket lets cold air leak out continuously, which forces the compressor to run longer and more often just to hold temperature, and often shows up as visible frost or condensation forming right at the seal. It directly replaces AP3038628, 2171185, 2181893, 2196241, 2221313, 2309529, 443026, AH323906, EA323906, EAP323906, PS323906, and W10912133. As a genuine OEM part, the 2159083 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 2159083 Genuine OEM Whirlpool Refrigerator Door Gasket fixes Whirlpool side-by-side refrigerators where the fresh food door doesn't seal properly, cold air leaks out, energy bills have climbed, or condensation and frost form around the door edge. Black, approximately 19-1/4"W x 62"H, for the fresh food (refrigerator) door specifically. Replaces AP3038628, 2171185, 2181893, 2196241, 2221313, 2309529, 443026, AH323906, EA323906, EAP323906, PS323906, W10912133. This is the fresh food door gasket — the matching freezer door gasket is a separate part, 2159082. Common Problems This Part Fixes Fresh food compartment running warmer than it should, or refrigerator running constantly Door not closing properly or not staying sealed against the cabinet Visible cracks, tears, or permanent creases in the rubber gasket Condensation forming around the door seal or on the cabinet near the door Frost or ice buildup near the door edge inside the fresh food compartment Noticeably higher energy bills as the compressor works harder to maintain temperature Gasket that feels stiff, brittle, or has lost its flexibility with age Weak or inconsistent magnetic seal — the door doesn't "pull shut" the way it used to Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator door gasket directly replaces the following OEM and cross-reference part numbers: 2159083, AP3038628, 2171185, 2181893, 2196241, 2221313, 2309529, 443026, AH323906, EA323906, EAP323906, PS323906, W10912133 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This fresh food door gasket is compatible with select Whirlpool side-by-side refrigerators across the Whirlpool family of brands, including: Whirlpool side-by-side refrigerators — WRS325 and WRS315 series Maytag side-by-side refrigerators (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana refrigerators (select models) Magic Chef, Admiral, Norge, and Roper refrigerators (select models) Estate and Inglis refrigerators (select models) Select Kenmore and Ikea refrigerators built on the Whirlpool platform Verified model numbers include: WRS325FDAM, WRS325FDAM02, WRS325FDAM04, WRS325SDHZ, WRS325SDHW, WRS315SDHZ, and WRS315SDHM. Note — fresh food door only: This is the gasket for the fresh food (refrigerator) door. The matching gasket for the freezer door on these same side-by-side models is a separate part, 2159082 (a different size, replacing a different set of numbers). The two are not interchangeable — check which door is actually failing to seal before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified rubber compound, profile, and embedded magnetic strip Creates an airtight magnetic seal around the fresh food door to keep cold air in and warm air out Resolves "door not sealing," "condensation at the door," "frost buildup," and "refrigerator running constantly" symptoms caused by gasket failure Black finish, approximately 19-1/4" wide by 62" tall Direct drop-in replacement — mounts to the original inner door panel retaining channel Replaces AP3038628, 2171185, 2181893, 2196241, 2221313, 2309529, 443026, AH323906, EA323906, EAP323906, PS323906, and W10912133 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, Inglis, and Kenmore side-by-side refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair — typically 30 to 60 minutes Product Specifications Part Number 2159083 Part Type Refrigerator Door Gasket — Fresh Food Door Condition Genuine OEM Brand Whirlpool Application Side-by-Side Refrigerators Color Black Width Approx. 19-1/4 in. Height Approx. 62 in. Seal Type Magnetic strip embedded in flexible rubber gasket Companion Part 2159082 (freezer door gasket, sold separately) Repair Difficulty Easy to Moderate — 30 to 60 minutes Quantity 1 gasket Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, Inglis, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Soften The Gasket First For An Easier Fit Disconnect power at the outlet before beginning. Wear work gloves. The gasket is held in a retaining channel around the inside edge of the door, usually secured by a continuous strip or a series of screws under a flap of the gasket itself — starting at one corner, gently pull back the inner lip of the old gasket to expose the retaining screws, then work your way around the door removing them. New gaskets can arrive stiff from packaging and folded for shipping, which makes them harder to seat evenly. Before installing, soften the new gasket by soaking it in warm water for several minutes, or by gently warming it with a hair dryer on low heat — this makes it far more pliable and easier to seat without permanent creases. Starting at the top corner, tuck the gasket's inner lip into the retaining channel and work around the door, replacing the screws as you go, checking periodically that the gasket lies flat with no twists, folds, or overlaps. Once fully installed, close the door and run your hand around the full perimeter feeling for warm spots or drafts, and use a piece of paper as a simple test — close the door on it at several points around the seal and check that it takes light resistance to pull out. Address any folds or creases immediately, since a gasket that seals with a crease in it will not hold that seal over time. Tools needed: flat-head or Phillips screwdriver (model-dependent), warm water or hair dryer, work gloves. Frequently Asked Questions How do I know if it's the fresh food gasket or the freezer gasket that's failing? Check which door is actually leaking air — run your hand around the inside edge of each door with the refrigerator running, or use the paper test (close the door on a strip of paper at several points and see if it pulls out too easily). Whichever door fails that test is the one that needs its gasket replaced. This 2159083 listing is specifically for the fresh food (refrigerator) door; the freezer door on these same side-by-side models uses a separate part, 2159082. The new gasket is stiff and hard to seat evenly. What can I do? This is normal — gaskets often arrive stiff and creased from packaging. Softening the gasket before installation makes a real difference: soak it in warm water for a few minutes, or gently warm it with a hair dryer set on low heat, then work it into the retaining channel while it's still pliable. A gasket installed with folds or creases won't seal properly even if it's brand new, so take the extra few minutes to get it lying flat. How can I confirm the gasket is actually the problem before I order? The classic test is the dollar-bill or paper test: close the door on a strip of paper at several points around the full perimeter of the seal and gently pull it out. If it slides out with little to no resistance at any point, the seal has failed at that spot. Also visually inspect the gasket for cracks, tears, permanent creases, or a soft, mushy feel to the rubber — any of these confirm it's time to replace it rather than looking elsewhere for the cause of a warm refrigerator. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound, profile, dimensions, and embedded magnetic strip of the fresh food door gasket originally installed on your side-by-side refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4970FR2084Z Washer Suspension Spring The XPARTCO 4970FR2084Z is an aftermarket replacement suspension hinge spring for LG and Kenmore front-load washers. The suspension springs support and stabilize the outer tub during wash and spin cycles and help it stay steady through unbalanced loads. When a spring is broken, snapped, or stretched, the washer may make a loud noise during spin, vibrate heavily, or stop spinning. This is a direct-fit aftermarket replacement for the original LG spring. A broken spring can let the drum drop and damage the shocks, dampers, and door seal, so inspect those parts while the washer is open. Quick Answer The XPARTCO 4970FR2084Z Suspension Spring fixes an LG or Kenmore front-load washer that is loud or shakes badly during spin, stops spinning, or has a drum that has dropped because a suspension spring is broken or stretched. Classic symptom: a loud banging or grinding noise on spin, as if something snapped inside the washer. Common Problems This Part Fixes Loud drum noise during the spin cycle Excessive vibration or shaking on spin Washer stops spinning or stops mid-cycle Drum looks lowered, or the front door seal is pushed forward Visibly broken, snapped, or stretched spring Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This suspension spring directly replaces the following part numbers: 4970FR2084Z, MHY62964802, AGF75223050, MHY57694605, MHY62964801, ALG51959, AP4998892, AH3524578, EA3524578, OEM14996685, PD00028343, PS3524578 These numbers span several generations of LG's own part numbering for this spring as washer models were updated. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This suspension spring is listed for LG and Kenmore front-load washers, including these examples: LG WM3470HWA, WM3360HWCA, WM3700HVA, WM3770HVA, WM4370HWA, WM5000HWA LG WM2601HW, WM2801HWA, WM2901HVA, WM3001HWA, WM3875HWCA Kenmore 79641172212, 79641182311 Note: The models above are a sample of more than 100 listed models, not a full list. Washers use more than one suspension spring, and customers often replace the springs on both sides together, so check how many your model uses. Confirm your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket suspension hinge spring for LG and Kenmore front-load washers Supports and stabilizes the outer tub during wash and spin cycles Resolves loud spin noise and vibration caused by a broken or stretched spring Fits a long list of LG and Kenmore front-load models Product Specifications Part Number XP4970FR2084Z OEM Part Number 4970FR2084Z Part Type Washer Suspension Hinge Spring Condition Aftermarket Replacement Application LG & Kenmore Front-Load Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer and turn off the water supply before beginning, and wear work gloves. Follow your model's service guide to reach the springs, which usually means removing the top and front panels. The drum is heavy, so have a second person lift it, or use a rope loop, while you hook the new spring, which customers say is the hardest step. Check the shocks, dampers, hoses, and door seal while you are in there, since a dropped drum can damage them. Reassemble, then run a spin cycle and check the washer is steady. Frequently Asked Questions My washer is very loud on spin. Is this the part I need? A broken or stretched suspension spring is a common cause of loud spin noise and heavy vibration, especially if it sounded like something snapped. Check the springs, shocks, and dampers for damage. Should I replace all the springs? Many customers replace the springs on both sides together, since an old spring may stretch or fail soon after. Check your parts diagram for how many your model uses. Is this an easy repair? Retailers rate it easy to moderate, with customers reporting from under 15 minutes to 2 hours. Hooking the new spring while holding up the drum is the hardest part, so a helper makes it easier. Will this fit my washer? It is listed for many LG and Kenmore front-load washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11220230 Washer Water Inlet Valve The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.. Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors. Quick Answer The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation. Common Problems This Part Fixes Washer not filling with water Slow water fill during cycles Water continuously flowing into washer Incorrect water temperature Washer stopping due to fill errors Leaking or stuck inlet valve Replaces Part Numbers This water inlet valve replaces the following part numbers: W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select washers from the following brands: Whirlpool washers Maytag washers Amana washers Kenmore / Sears washers (select models) Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Three coil hot and cold water valve. OEM-equivalent fit, performance, and durability Restores proper water fill levels and cycle operation Durable construction resists mineral buildup and wear Prevents leaks and overfilling issues Direct replacement for W11220230 valve assembly Product Specifications Part Number W11220230 Part Type three coil hot and cold water inlet valve. Application Top Load / Front Load Washers Condition Aftermarket Replacement Function Controls Water Flow Compatible Brands Whirlpool, Maytag, Amana, Kenmore Installation Notes ⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation. Frequently Asked Questions What does a washer water inlet valve do? It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill. Will this fix a washer that won’t fill? Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less