Search results for "knobs"

XPARTCO W10195039 Dishwasher Float Switch The XPARTCO W10195039 is an aftermarket replacement float switch for Whirlpool-built dishwashers sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana and related brand names. The float switch is the safety device that shuts off the water fill valve if the water level gets too high before the timed fill cycle ends, so a failed float can mean overfilling or a dishwasher that won't fill properly. This is a direct-fit aftermarket replacement for the original Whirlpool float switch, which is sold as W10195039 and WPW10195039. Float problems can look like valve or control problems, so check the float for a stuck or damaged action before replacing it. Quick Answer The XPARTCO W10195039 Float Switch fixes a Whirlpool-built dishwasher that overfills, leaks from too much water, or won't fill because the float is stuck, damaged, or no longer switching. It is also listed as WPW10195039. Classic symptom: water keeps filling past the normal level, or the dishwasher won't fill and the float looks stuck or cracked. Common Problems This Part Fixes Dishwasher overfills or the water level gets too high Water leaking from too much water in the tub Dishwasher won't fill because the float switch is stuck or failed Float is cracked, broken, or doesn't move freely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This float switch directly replaces the following part numbers: WPW10195039, W10195039, W10734532, 1872053, MS10-06, AP6016738, AWP49215, EAP11750031, PD00002753, PS11750031 W10195039 is the older Whirlpool number and WPW10195039 is its current replacement. W10734532 comes from a single retailer cross-reference, so confirm against your dishwasher's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This float switch is listed for Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana, and Inglis dishwashers, including these examples: Kenmore 66513979K017, 66515049K111, 66513964K017, 66512776K310 ADB1100AWB0, CDBW4400SB0, KUDC10FBBL0, KUDS30FXSS0, MDB4709PAB0 Note: The models above are a sample of a much longer list, not a full list. A dishwasher that won't fill can also be caused by the inlet valve, so test the float and valve before ordering. Confirm your model number against your parts diagram, or contact our support team to verify fit. Key Features Direct-fit aftermarket float switch for Whirlpool-built dishwashers Shuts off the fill valve if the water level gets too high Replaces both W10195039 and WPW10195039 Fits Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air and related brands Product Specifications Part Number W10195039 OEM Part Number W10195039, WPW10195039 Part Type Dishwasher Float Switch Condition Aftermarket Replacement Application Whirlpool-Built Dishwashers Installation Notes ⚠️ Disconnect Power and Shut Off the Water Unplug the dishwasher or switch off its circuit breaker, and turn off the water supply before beginning. Wear work gloves to protect your hands. Follow your model's service guide to reach the float switch, and note the position of each wire connector before disconnecting it. Install the new float switch in the same position, reconnect the wires, and check that the float moves freely before closing the dishwasher. Run a cycle and check for leaks. Frequently Asked Questions What does the float switch do? It shuts off the water fill valve if the water level gets too high before the timed fill cycle ends. It is a safety device that helps prevent overflow. My dishwasher still won't fill. Will this fix it? Only if the float is the cause. A dishwasher that won't fill can also have a bad inlet valve, a clogged inlet screen, or a control problem. Check that the float moves freely and test the valve first. Is W10195039 the same as WPW10195039? Yes. W10195039 is the older Whirlpool number and WPW10195039 is its replacement. This float switch covers both. Will this fit my dishwasher? It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570 This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features 2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 2 kits per order (2 door catches and 2 strikes in total) Product Specifications Part Number EXP570 (2 Pack) OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike per Kit Quantity 2 Kits (2 Door Catches & 2 Strikes) Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly The AHA72973309 is a genuine LG OEM drain and circulation pump assembly for LG and select Kenmore front-load washers. This is a dual-purpose pump — an Askoll M120-2 unit — that handles two separate jobs from one motor and housing. During the drain portion of the cycle, it pumps wastewater out of the tub and out through the drain hose. During the wash and rinse portions, it switches roles and recirculates water from the bottom of the tub back up through the dispenser and spray nozzle, showering it back over the load. That recirculation spray is what lets LG's front-load washers clean effectively with less water than an older top-load design would need. Because this single assembly performs both functions, a failure here can show up in more than one way: standing water left in the tub after a cycle, a washer that won't complete its drain step, unusual grinding or humming noise, or reduced wash performance if the recirculation spray isn't working even though draining still seems fine. Common causes include debris such as coins, buttons, or lint lodged in the impeller, general wear and tear on the motor bearings, or an electrical failure in the pump motor itself. It directly replaces AP5676608, 2659237, AHA72973304, and PS7788830. As a genuine OEM part, the AHA72973309 is manufactured by LG to factory specifications — guaranteed fit, materials, and performance. Quick Answer The AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly fixes LG and select Kenmore front-load washers with standing water left in the tub after a cycle, a washer that won't drain, unusual grinding or humming noise, or reduced wash performance from a weak recirculation spray. Askoll M120-2 dual-purpose pump — handles both draining and mid-cycle water recirculation. Replaces AP5676608, 2659237, AHA72973304, PS7788830. Installation is average difficulty, 30 to 60 minutes — and on many models it's accessible through the front panel without needing to tip the washer over. Common Problems This Part Fixes Standing water left in the tub after a cycle finishes Washer won't drain, or drains very slowly Drainage-related error code displayed on the control panel Unusual grinding, humming, or rattling noise during the drain or wash portion of the cycle Reduced wash performance — clothes not getting as clean, possibly from a weak recirculation spray Washer stalling mid-cycle at the drain step Water leaking from underneath the washer near the pump housing Pump that hums but doesn't seem to move water — possible clog or seized impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain and circulation pump assembly directly replaces the following OEM and cross-reference part numbers: AHA72973309, AHA72973304, AP5676608, 2659237, ALG53336, PD00024680, PS7788830 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain and circulation pump assembly is compatible with select LG front-load washers, and also fits select Kenmore and Kenmore Elite front-load washers built on the LG platform. Note: This is a dual-function drain-and-circulation assembly specific to LG's front-load platform, built around the Askoll M120-2 pump. It is not a drain-only pump, and it is not intended for top-load washers, which use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor, impeller, and housing design Dual-purpose Askoll M120-2 pump — drains the tub and recirculates wash water through the dispenser spray nozzle Resolves "standing water in the tub," "won't drain," "grinding or humming noise," and "reduced wash performance" symptoms caused by pump failure Includes all necessary wiring and mounting hardware for a complete replacement Direct drop-in replacement — no modification required Replaces AP5676608, 2659237, AHA72973304, and PS7788830 Compatible with LG and select Kenmore/Kenmore Elite front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Average installation difficulty — typically 30 to 60 minutes Product Specifications Part Number AHA72973309 Part Type Washer Drain & Circulation Pump Assembly Condition Genuine OEM Brand LG Pump Model Askoll M120-2 Function Drains tub water and recirculates wash water through the dispenser spray Kit Contents Pump assembly with wiring and mounting hardware Application Front-Load Washers (LG-Built) Repair Difficulty Average — 30 to 60 minutes Quantity 1 pump assembly Compatible Brands LG, select Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Drain Residual Water First Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Place towels down and have a shallow pan ready, since the pump housing will hold residual water even after a completed cycle — draining this into a pan before disconnecting hoses will save you a mess. On many models, this pump is fully accessible by removing the front lower access panel or kick plate, without needing to tip the washer onto its back — check this first, since it can save significant time and effort compared to some online guides that recommend tipping the unit. Photograph the hose routing and wiring connections before disconnecting anything. Disconnect the two hose clamps connecting the pump to the tub and drain hose, and unplug the electrical connector from the pump motor. Remove the mounting screws or clips securing the pump assembly and lift it free, checking the impeller area for coins, buttons, or debris while it's out — clearing a clog here may have been the actual cause of the original symptom. Install the new AHA72973309 in the same orientation, reconnect both hoses with their clamps, and reconnect the electrical connector fully. Reinstall the front access panel, restore water and power, and run a short cycle to confirm normal draining, recirculation spray, and no leaks around the pump housing. Tools needed: Phillips screwdriver, hose clamp pliers, shallow pan or towels, work gloves. Frequently Asked Questions Do I really need to tip the washer over to replace this pump? Not necessarily — check your model first. While a lot of general online guidance recommends tipping the washer onto its back to access the pump from underneath, many LG and Kenmore Elite front-load models make this pump fully accessible through the front lower access panel or kick plate instead, without any tipping required. It's worth removing that panel first and seeing what you find before committing to the more involved tip-over approach. Why does this one pump handle both draining and something during the wash cycle? LG's front-load washers use this same Askoll pump for two different jobs at different points in the cycle: pumping wastewater out during the drain step, and recirculating water from the bottom of the tub back up through the dispenser and spray nozzle during wash and rinse to shower it over the load. That recirculation spray is part of how these washers clean effectively while using less water than an older top-load design. Because one pump does both jobs, a failure can affect draining, wash performance, or both, depending on what's actually gone wrong inside it. There's water left in the tub after every cycle. Is this definitely the pump? It's one of the most common causes, but check the easy things first. A clogged drain filter or a kinked drain hose can produce the same "won't drain" symptom and cost nothing to fix. If the filter and hose are clear and water is still standing in the tub, or if the pump hums but doesn't seem to move any water, the pump assembly itself has likely failed. My washer drains fine but clothes aren't coming out as clean. Could this pump be the cause? Possibly. Since this same assembly also handles the recirculation spray during wash, a partial failure can leave draining intact while weakening or eliminating that spray function, which reduces how effectively detergent and water reach the load. If drainage is normal but wash performance has noticeably declined, it's worth having this pump checked as one possible cause alongside things like detergent dosing and water hardness. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same Askoll M120-2 dual-function pump design, wiring, and mounting configuration as the drain and circulation pump assembly originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10810403 Washer Lid Switch Assembly The XPARTCO W10810403 is an aftermarket replacement lid lock assembly for Whirlpool Cabrio and Maytag Bravos XL top-load washers. Positioned on the underside of the washer lid, this assembly detects whether the lid is open or closed and locks it shut during the wash cycle, preventing the washer from spinning or agitating — and preventing the lid from being opened — while the cycle is running. This is a safety mechanism as much as a functional one, keeping users from contacting moving parts or being splashed by water or detergent mid-cycle. This assembly includes the lid lock mechanism and its wiring harness, and ships with a white bezel. Many of these lid locks also contain an internal fuse as part of the switch circuit — if that fuse blows, the symptom isn't limited to lid-related errors; it can prevent the entire control board from powering up at all, since the switch sits in the same circuit path. A failing lid lock typically shows up as the lid not closing or locking properly, the washer failing to start, the cycle stopping mid-way, or in more severe cases, a completely unresponsive control panel with no lights at all. It directly replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, and PS11731620. Quick Answer The XPARTCO W10810403 Washer Lid Switch Assembly fixes Whirlpool Cabrio, Maytag Bravos XL, and select Kenmore 600/700 Series top-load washers where the lid won't lock, the washer won't start, the cycle stops mid-way, or the control panel is completely unresponsive with no lights. White bezel. Replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, PS11731620. If your original lock has a grey bezel, you need part number W10861642 instead — same mechanism, different bezel color, so match the color of your existing lock before ordering. Common Problems This Part Fixes Lid won't lock or lock reliably during the cycle Lid won't open after a cycle finishes Washer won't start Washer won't agitate or spin because the lid isn't sensed as locked Cycle stops partway through Washer pumps but won't spin Control panel completely unresponsive with no lights, potentially from an internal fuse in the switch circuit Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select Whirlpool Cabrio and Maytag Bravos XL top-load washers, and also fits select Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea washers built on the same platform, including model numbers such as MVWB855DW1, MVWB865GW1, MVWB835DW3, and MVWB765FW4. Note — bezel color and lid lock platform both matter: This assembly has a white bezel. If your original lock has a grey bezel, order W10861642 instead — same lock mechanism, different bezel color. Separately, Whirlpool has used several distinct lid lock designs across its Cabrio-era washer lineup, including a different 3-wire electronic lock (our W11670519 listing) used on other Cabrio/MVW models. These are not the same part despite both serving Cabrio-platform washers. Always verify your full model number and match your original lock's exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement lid lock assembly — includes the lock mechanism and wiring harness Resolves "lid won't lock," "washer won't start," "cycle stops mid-way," and "unresponsive control panel" symptoms White bezel finish Safety mechanism that prevents lid opening and drum movement from occurring at the same time Direct drop-in replacement — mounts to the original position on the underside of the lid Replaces W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 Compatible with Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10810403 OEM Part Number W10810403 Part Type Washer Lid Lock/Switch Assembly Condition Aftermarket Replacement Application Whirlpool Cabrio / Maytag Bravos XL Top-Load Washers Bezel Color White (grey bezel = W10861642) Included Components Lid lock mechanism + wiring harness Location Underside of the washer lid Repair Difficulty Easy — basic hand tools Quantity 1 lid switch assembly Compatible Brands Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, Ikea Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W10810403 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My control panel has no lights at all. Could the lid lock really cause that? Yes, and this is a less obvious but documented cause. Some of these lid lock assemblies include an internal fuse as part of the switch circuit. If that fuse blows, it can prevent the control board from powering up entirely, producing a completely dark, unresponsive panel rather than a symptom that's obviously tied to the lid. If your washer has no lights and no response at all, this lock assembly is worth checking alongside the more obvious suspects. My old lock has a grey bezel. Can I still use this part? This specific listing has a white bezel. If your original lock is grey, order part number W10861642 instead — it's the same lock mechanism, just finished with a grey bezel to match certain washer trim colors. Using the wrong bezel color won't affect function, but it will look mismatched against your washer's lid. Is this the same lock used on all Cabrio washers? No — Whirlpool has used more than one lid lock design across its Cabrio-era lineup. This W10810403 is a distinct assembly from other Cabrio/MVW-platform locks, such as our W11670519 listing, which uses a different 3-wire electronic locking design. Always match your exact original part number rather than assuming any "Cabrio lock" will fit, since the mounting and electrical interface can differ between designs. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the locking mechanism, wiring harness, and bezel design of the original W10810403 lid lock assembly used in compatible Whirlpool Cabrio, Maytag Bravos XL, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406107 Dryer Door Switch Replaces WP3406107 The XPARTCO 3406107 is an aftermarket replacement door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. Mounted inside the upper corner of the front panel, this safety switch has a spring-loaded black tab that gets pressed in when the door closes. That contact tells the control board the door is shut, which is required before the dryer will start, and it also powers the interior drum light. Over time the switch's internal contacts wear out or the tab loses spring tension, and the dryer either won't start at all or runs with the door open — a safety condition the switch is specifically designed to prevent. This is a three-wire SPDT (single pole, double throw) switch built to the same dimensions and mounting points as the original, and it's designed to remain compatible with older two-wire harnesses as well. Direct-fit aftermarket replacement, no wiring modifications needed. Quick Answer The XPARTCO 3406107 Dryer Door Switch fixes a dryer that won't start, runs with the door open, or has a dead interior light. Direct-fit replacement for OEM WP3406107. Classic symptom: pressing start does nothing until you push and hold the door shut, or the drum light never comes on. Common Problems This Part Fixes Dryer won't start even though the door is closed Dryer runs with the door open (safety switch failure) Interior drum light doesn't turn on Door doesn't seem to latch or seal properly against the switch tab Drum doesn't spin, or cycle stops intermittently Touchpad or start button appears unresponsive Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, AWP47183, PS11741701 This switch design was updated to a three-wire configuration at some point in its production history (superseding older 3405100/3405101/3406100/3406101 numbers), but the current three-wire version remains compatible with older two-wire harnesses, so it's a safe direct replacement across all of these part numbers. Compatibility This door switch is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including units across the: Whirlpool/Kenmore Series 60, 70, 80, 90, 500, 600, 700, and 800 dryer lines AED4475TQ1, MEDC400VW0, and numerous additional model numbers Note: This switch has been used across a very wide range of Whirlpool-built dryers (including Kenmore, Maytag, and KitchenAid badged units) spanning many production years, so the list above is only a sample. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket door safety switch for Whirlpool-built dryers Three-wire SPDT design, backward-compatible with two-wire harnesses Controls both the start-permission safety interlock and the interior drum light Resolves no-start, runs-with-door-open, and dead-light symptoms White plastic and metal tab construction, approx. 6.5" length Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number 3406107 OEM Part Number WP3406107 Part Type Dryer Door Safety Switch Condition Aftermarket Replacement Switch Type SPDT (Single Pole, Double Throw) Wire Configuration Three-Wire (Backward-Compatible with Two-Wire Harnesses) Length Approx. 6.5 Inches Color / Material White; Plastic & Metal Construction Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. The switch is mounted inside the upper corner of the front panel, so you'll need to remove the front panel or top panel per your model's service guide to access it. Disconnect the wire connector from the old switch, then remove the mounting screw(s) holding it in place. Install the new switch in the same position, reconnect the wire connector, and reinstall the panel. Before closing everything up, you can test the switch by pressing the black tab — you should feel spring resistance and hear or feel a distinct click. Restore power and confirm the dryer starts normally with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start — is this the part I need? This is one of the most common causes of a dryer that won't start even with the door closed. Try pressing the black tab on the switch by hand — if it feels loose, doesn't click, or offers no resistance, the switch has likely failed and needs replacement. My dryer runs even with the door open — is that dangerous? Yes, this indicates the door safety switch has failed in a way that no longer prevents operation with the door open, which is a safety hazard. Replace the switch promptly and avoid running the dryer with the door open in the meantime. My dryer has a two-wire connector — will this three-wire switch still work? Yes. This switch was redesigned to a three-wire configuration but remains compatible with older two-wire wiring harnesses, so it's a safe direct replacement regardless of which wire configuration your dryer currently has. Does this switch also control the interior light? Yes. This switch serves a dual function — it's the safety interlock that permits the dryer to run only with the door closed, and it also powers the interior drum light when the door is open. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool W11428245 Range Genuine OEM Screw Factory-original replacement screw for select Whirlpool, Roper, and Estate ranges. Product Description W11428245 is a Genuine Whirlpool OEM range screw. On many compatible gas ranges it is used as the surface burner valve mounting screw. It supersedes original Whirlpool part number 98005521. Quick Answer If your parts diagram calls for W11428245 or 98005521, this is the genuine Whirlpool OEM replacement. Verify the complete appliance model and screw location before ordering because Whirlpool ranges use several similar fasteners. Key Features Genuine Whirlpool OEM part Factory-correct range mounting screw Replaces 98005521 Commonly used for surface burner valve mounting Fits select Whirlpool, Roper, and Estate ranges Sold individually Replaces and Cross-References W11428245, 98005521, AP6981620, AWP44475, EAP12745627, PS12745627, PD00057954 Compatibility Confirmed model examples include WFG320M0BS3, WFG320M0MS0, WFG505M0BB2, WFG505M0MS0, SF110AXSQ0, SF114PXSB0, SF114PXSQ0, TGP310LW0, FGP300KN0, FGP300KW1, FGP305KW3, and FGP337KW1. Partial model list only. Verify your full appliance model number and the screw callout in the parts diagram before purchase. Product Specifications Part Number W11428245 Brand Whirlpool OEM Status Genuine OEM Part Type Range Mounting Screw Replaces 98005521 Common Use Surface Burner Valve Mounting Quantity 1 Screw Condition New Common Reasons for Replacement Original screw is missing Threads are stripped Screw head is damaged Burner valve or related component is loose Correct OEM hardware is required during reassembly Installation Notes Disconnect electrical power before service. Shut off the gas supply if servicing burner-valve or gas-manifold components. Verify the screw location in the model-specific parts diagram. Start the screw by hand to avoid cross-threading. Do not overtighten. Follow the appliance service procedure and complete any required gas-leak checks after servicing gas-system components. High-Quality Replacement Part Manufactured to meet or exceed original specifications for your appliance. Reliable, durable, and built to last. Shipping Information Free Tracking included with every order. We ship to the eBay-verified address only. Address changes after checkout cannot be guaranteed. Please double-check before purchasing. Compatibility Help Not sure if this part fits your appliance? Contact us anytime and we’ll gladly help confirm fitment. Payments & Tax We accept: Visa, MasterCard, Discover, AMEX, and PayPal. Applicable sales tax will be collected per eBay policy. Returns & Warranty Returns: Item must be in brand new, resalable condition. 20% restocking fee may apply. If shipping was free, it will be deducted from your refund. Buyer is responsible for return shipping. Please include a copy of the packing list or order number with a brief reason for return. Warranty: 30-Day Replacement or Money-Back Guarantee. Item must be returned before a replacement can be issued. Buyer is responsible for return shipping. Why Buy From Express Parts Direct? Trusted aftermarket replacement parts Fast shipping & free tracking Responsive customer service Simple return & warranty process Express Parts Direct

Read more less

XPARTCO WE03X29897 Dryer Drum Belt The XPARTCO WE03X29897 is an aftermarket replacement drum drive belt for GE, Hotpoint, and Kenmore dryers. It is a four-rib belt, approximately 89-1/2 inches long, that wraps around the drum, the tension pulley, and the drive motor pulley, so the motor can turn the drum. A worn, stretched, or broken belt can cause noise, a drum that won't turn, or a dryer that won't start. This is a direct-fit aftermarket replacement for the original GE belt. Because the drum has to be moved to fit a new belt, it is also a good time to inspect the tension pulley, idler, and drum rollers and replace any that look worn. Quick Answer The XPARTCO WE03X29897 Drum Belt fixes a GE, Hotpoint, or Kenmore dryer whose drum won't turn, that makes a noisy thumping or squealing sound, or that won't start because the belt is worn or broken. Classic symptom: the dryer hums or the motor runs, but the drum stays still. Common Problems This Part Fixes Drum does not turn although the motor runs Noisy dryer, with thumping or squealing as the drum turns Dryer won't start Heat stays on after the drum has stopped Visibly stretched, cracked, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part numbers: WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, 254C1413P002, 3516321, 4 PH 2275, SH210T, 4975431, WE12M0022, WE12M22, WE12M33, 559C197P004, 559C197P005, 559C197P006, WE120122, AGE25601, AP7012633, EAP10065160, PD00074201, PS16542496 These numbers span several generations of GE's own part numbering for this belt. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drum belt is listed for GE, Hotpoint, and Kenmore dryers and washer-dryer combos, including these examples: GE DBB3300EA0AA, DBLR333EE0CC, DNCK440GG9WC, DWXR473GT5WW GE DDC4400T3WH, DRSR495EG0WW, DX2300EB1WW, DX4500EG1WW GE 2661532210 and 3636154241, Kenmore 36371542 Note: The models above are a small sample of a list of hundreds, not a full list. Compare your old belt's length to this one (approximately 89-1/2 inches), and contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket drum drive belt for GE, Hotpoint, and Kenmore dryers Four-rib design, approximately 89-1/2 inches long Wraps around the drum, tension pulley, and motor pulley Resolves drum-not-turning, noise, and no-start problems caused by a worn belt Straightforward repair, typically 30 minutes to 1 hour Product Specifications Part Number XPWE03X29897 OEM Part Number WE03X29897 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Belt Length Approx. 89-1/2 Inches Belt Profile 4-Rib Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as internal parts and cabinet edges can be sharp. Remove the top and front panel as shown in your model's service guide, then slide the drum out, which is easier with a second person. Remove the old belt and route the new belt around the drum, the tension pulley, and the motor pulley as the old one ran, then reassemble in reverse order. Check the tension pulley and drum rollers while the drum is out and replace any that are worn. Frequently Asked Questions My dryer runs but the drum won't turn. Is this the part I need? That is the classic sign of a broken drum belt. If the motor runs and you can turn the drum freely by hand, check the belt first. How long is this belt? It is approximately 89-1/2 inches long, with four ribs. Small differences are normal, but if your old belt is a very different length, check your model number before ordering. Should I replace anything else while the drum is out? Inspect the tension pulley and the drum rollers or glides. These wear along with the belt, and they are much easier to replace now than later. Will this fit my dryer? It is listed for hundreds of GE, Hotpoint, and Kenmore dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP98014893 Oven Genuine Gas Safety Valve Description: The Gas Safety Valve is an OEM replacement part for Whirlpool gas ranges. This important safety device works to automatically shut off the gas supply to the range if abnormal flame conditions, such as flame rollout, occur. Replaces Part Numbers:WP98014893, W11399433, 98014893, 1061522, 98007439, AP6014264, PS11747502.   California Residents only WARNING: California’s Proposition 65

Read more less

XPARTCO 00619985 Dishwasher Mounting Bracket Kit - Compatible with Bosch, Thermador, Gaggenau, Kenmore Dishwashers Product Description Secure your dishwasher with the replacement XPARTCO 00619985 Mounting Bracket Kit. This kit provides sturdy brackets to fasten select Bosch, Thermador, Gaggenau, and Kenmore dishwashers to kitchen cabinets or countertops, ensuring stability and preventing tipping. It addresses issues like loose mounting, excessive vibration, or noise during operation, offering a cost-effective alternative to OEM parts. Note: Includes two mounting brackets and mounting screws (for top or side installation). Disconnect power before installation. Verify countertop or cabinet suitability for mounting. Replaces part numbers: 00619985, 00628371, 00605007, 1567804, 605007, 619985, 628371, AH3478789, EA3478789, PS3478789, PD00000071, AP4538351, PS8728568. Compatibility: Compatible with models including but not limited to: Bosch: SHX88PW55N/01, SHX89PW55N/01, SHX33M06UC/46, SHX33M05UC/46, SHX33M02UC/53, SHX33M02UC/52, SHX33M02UC/50, SHX33M02UC/46, SHEM3AY55N Thermador: DWHD94EP/50 Gaggenau: Select models requiring 00619985 Kenmore: Select models requiring 00619985 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Bosch, Thermador, Gaggenau, and Kenmore dishwashers. 🔥 Specifications: replacement mounting bracket kit, includes two stainless steel brackets and two 1.5" hex-head screws for top or side mounting. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, wrench, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves loose or unstable mounting, excessive vibration, or noise during operation. Product Specification Part Number: XP619985 Component Type: Mounting bracket kit Material: Stainless steel Weight: 3.0 oz (kit) Mounting Hardware: Includes two 1.5" hex-head screws Operating Conditions: Suitable for high-humidity kitchen environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dishwasher from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher stable and secure today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO (2 Pack) EXP571 Dryer Door Catch The XPARTCO (2 Pack) EXP571 is a two-pack of aftermarket replacement door catches for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 2 door catches. Quick Answer The XPARTCO (2 Pack) EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 2 catches per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 2 door catches per order Product Specifications Part Number EXP571 (2 Pack) OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 2 Door Catches Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 2 door catches. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

3W40025L Genuine LG OEM Dishwasher Micro Switch – Compatible with LG Dishwashers Product Description Restore proper operation to your dishwasher with the 3W40025L Genuine LG OEM Dishwasher Micro Switch. This small but essential component detects door position or button activations, ensuring cycles start and stop correctly. A failed micro switch can cause the dishwasher not to run, stop mid-cycle, or display error codes. Replacing it with this genuine LG part restores dependable performance and safety. Replaces Part Numbers 3W40025L, D3V-16G-1C25, PD00035953, EAP5574491, AP5650845 PS5574491. Compatibility This micro switch is compatible with select LG dishwashers. Example compatible models include (but are not limited to): LG LDF7774ST, LDF8764ST, and LDF6810ST. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 OEM Replacement – Genuine LG part for reliable performance 🔒 Cycle Safety – Ensures proper door detection and cycle control 💰 Cost-Effective OEM Part – Built to last with factory-tested quality 🛠️ Easy to Install – Small component, quick replacement with basic tools 🛡️ Fixes Common Issues – Resolves dishwashers not starting, stopping mid-cycle, or showing error codes 📐 Product Specification Part Number: 3W40025L Component Type: Dishwasher Micro Switch, 16A  125/250VAC Material: High-durability plastic housing with electrical contacts Mounting: Direct replacement switch with snap-in or screw mount Operating Conditions: Designed for standard dishwasher use Compliance: Genuine LG OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect the dishwasher from power before starting repairs. Steps: Disconnect power supply to dishwasher. Access control panel or door latch assembly (depending on model). Locate and remove the faulty micro switch. Install the new 3W40025L switch and reconnect wiring. Reassemble the control panel or door latch assembly. Restore power and test dishwasher operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dishwasher running properly again — Add to Cart Now for a genuine, factory-approved fix!

Read more less

XPARTCO 12138200000320 Dryer Door Catch The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle. This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases. Quick Answer The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Dryer requires the door to be held or pushed to stay running Replaces Part Numbers This door catch directly replaces the following part numbers: 12138200000320, AP7152622, PS18161385. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch is compatible with select dryers from the following brands: Midea dryers (gas and electric — select models) Insignia dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door closed and activates the door switch so the dryer can run safely Snap-in installation — no tools required in most cases; installs in under 5 minutes Durable plastic construction — designed to withstand repeated opening and closing Sold individually — one door catch per order Replaces AP7152622 and PS18161385 Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 12138200000320 Part Type Dryer Door Catch (Door Latch Clip) Condition Aftermarket Replacement Application Gas and Electric Dryers Material Plastic Installation Snap-in — no tools required Sold As Single door catch Compatible Brands Midea, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal. Frequently Asked Questions What dryers is the 12138200000320 compatible with? The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly. Why won't my dryer start even though I'm closing the door? If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked. Do I need to replace the door strike as well? Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less