Search results for "knobs"

XPARTCO 316233903 Oven Temperature Sensor The XPARTCO 316233903 is an aftermarket replacement oven temperature sensor (probe), made to replace Frigidaire part 316233903, for select Frigidaire, Kenmore, Tappan, Crosley and White-Westinghouse gas and electric ranges. The sensor constantly monitors the temperature inside the oven and sends signals to the control board, which uses them to hold the set temperature for baking, roasting and broiling. When it fails, the oven may not heat properly, may not hold temperature, or may run too hot. This is an aftermarket replacement from XPARTCO, not a genuine Frigidaire part. It is sold individually. Check your model number before ordering, and compare the sensor's plug with your old one, because connectors can differ. Quick Answer The XPARTCO 316233903 Oven Temperature Sensor replaces the oven sensor probe on a compatible range when it has failed. Replaces 316217008, 316233900 and 316233902. Classic symptoms: little or no heat when baking, uneven heating, an oven that runs too hot, or an oven that won't start. Common Problems This Part Fixes Little or no heat when baking Oven not heating evenly Oven running too hot Oven won't start Inaccurate oven temperature Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven temperature sensor is made to replace the following Frigidaire part numbers: 316233903, 316217008, 316233902, 316233900, AFR16108, AP5998652, OEM17995965, PD00027614, PS11731754 If your old sensor shows a different number, contact our support team and we'll check whether it matches. Compatibility This oven temperature sensor is listed for Frigidaire, Kenmore, Tappan, Crosley and White-Westinghouse gas and electric ranges, including these examples: Frigidaire CFEF3043RSD, CFEF3043RSC, CWEF3007TWB, FFLF3049SSB, FFGF3052TSA, TGF328GSF Crosley CRG3150SSA, CRG3150SSB, CCRE3530LWG White-Westinghouse WWEF3001TWA, WWGF3008TWA, WWGF3008TWB Kenmore 79073033314, 79073033315, 79073033316, 79061750100 Note: The models above are a sample, not a full list. This sensor may require cutting and splicing the wire connector, and some buyers report that the plug on their range did not match, so compare it with your old sensor. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the Frigidaire 316233903 oven temperature sensor Monitors oven temperature and signals the control board Cross-references three earlier Frigidaire sensor part numbers Sold individually Product Specifications Part Number XP316233903 OEM Part Number 316233903 Part Type Oven Temperature Sensor (Probe) Condition Aftermarket Replacement Quantity 1 Sensor Application Select Gas and Electric Ranges Installation Notes ⚠️ Disconnect Power Before Installing Unplug the range or shut off its circuit breaker, let the oven cool, and wear work gloves. Pull the range out to reach the back panel, remove the panel, then unscrew the old sensor and disconnect its wiring. Mount the new sensor in the same position and reconnect the wiring. Note: this sensor may require cutting and splicing the wire connector. If the plug differs from your old one, cut the connector and splice the wires with porcelain wire nuts. Refit the panel, restore power, and check oven temperature accuracy. Frequently Asked Questions My oven isn't heating right. Is the sensor the problem? It can be, but not always. Some customers found the real fault was the igniter, bake element or control board. Test the sensor and check those parts before replacing it. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace Frigidaire part 316233903. If you specifically need a genuine Frigidaire part, contact our support team. Will I need to cut and splice the wire connector? Yes, it may. This sensor may require cutting and splicing the wire connector, depending on your range. Compare your old sensor with this one before ordering. Customers have spliced the wires with porcelain wire nuts when the plug differed. Contact our support team if you are unsure. Will this fit my range? It is listed for many Frigidaire-built models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3949238 Washer Lid Switch Replaces WP3949238 The XPARTCO 3949238 is an aftermarket replacement lid switch assembly for Whirlpool top-load washers, and also fits select Kenmore models. This switch confirms the lid is closed before the washer will spin — a pin on the underside of the lid pushes against the switch's lever, telling the machine it's safe to proceed with the cycle. Includes a 3-wire lead and a metal shield for added durability. Over time, the switch's internal contacts can wear out or fail electrically. If your washer will agitate but won't spin, this switch is a strong candidate for the cause. Symptoms of a failing lid switch include the washer not spinning, not draining, not starting, not agitating, the cycle failing to advance, or the lid not closing properly. It directly replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021. Quick Answer The XPARTCO 3949238 Washer Lid Switch fixes Whirlpool and Kenmore top-load washers that won't spin, won't drain, won't start, won't agitate, won't advance through the cycle, or have a lid that won't close properly. Includes 3-wire lead, metal shield. Replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021. If your washer agitates fine but won't spin, that's the classic symptom pointing to this switch. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting Washer not agitating Cycle not advancing Lid or door won't close properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch is compatible with select Whirlpool top-load washers, and also fits select Kenmore washers built on the Whirlpool platform, including model numbers such as 11015732400, 11015842400, 11015852400, 11020692000, 11020602992, 11020612990, 11020612991, 11020622990, 11020622991, 11020632990, 11020632991, 11020642990, 11020642991, 11021894000, 11022292100, 11022294100, 11022422100, 11022432100, 11022442100, 11022622100, 11022632100, 11022642100, 11022652100, 11022662100, 11022692100, 11022692101, 11022702100, 11022702101, 11022712100, 11022722100, and 11022722101. Note — not the same as 3949247: A similarly-numbered switch, 3949247, is a separate part used on different models. Whirlpool also uses several other distinct lid switch designs, including the direct-drive style (8318084) and the thin-twin style (3355806), which are not interchangeable with this switch. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your washer needs. Key Features Aftermarket replacement lid switch assembly — confirms the lid is closed before allowing the washer to spin Resolves "won't spin," "won't drain," "won't start," "won't agitate," "cycle not advancing," and "lid won't close" symptoms 3-wire lead with metal shield for added durability Direct drop-in replacement matching the original mounting and connection Replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021 Compatible with Whirlpool and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Requires basic hand tools, some disassembly, novice repair experience Product Specifications Part Number 3949238 OEM Part Number WP3949238 Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Wiring 3-wire lead Shield Metal Function Confirms lid is closed before allowing the washer to spin Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 lid switch assembly Compatible Brands Whirlpool, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Unplug your washer and turn off the water supply before you begin — make sure both the hot and cold water supplies are shut off. Remove the screws located on the back of the washer cabinet, usually located at the top of the access panel. Lift or tilt the top of the washer to access the lid switch, typically mounted near the lid opening. Photograph the wiring before disconnecting anything. Disconnect the wire connectors from the old switch and remove the mounting screws securing it in place. Install the new 3949238 in the same position, reconnect the wire connectors fully, and secure the mounting screws. Reassemble the washer cabinet and secure its screws. Restore power and water, then run a test cycle with the lid closed to confirm the washer spins normally. Tools needed: multi screwdriver. Frequently Asked Questions My washer agitates but won't spin. Is this the part I need? Yes, this is the classic and most reliable symptom of a failed lid switch. This switch confirms to the washer's control system that the lid is closed before allowing the spin cycle to run — a failed switch commonly still allows agitation while preventing spin, since spin specifically requires the lid-closed signal. Is this the same as the 3949247 switch I've seen listed nearby? No, these are separate lid switch part numbers, despite the similar numbering. 3949247 is used on different models. Always confirm your exact part number from your washer's parts diagram or the sticker on your old switch before ordering. Is this a difficult repair? No, this is a straightforward repair requiring basic hand tools and some cabinet disassembly, suitable for a novice DIYer. A multi screwdriver is typically all that's needed. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the wiring, mounting, and switching function of the original WP3949238 lid switch assembly used in compatible Whirlpool and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP572 Dryer Door Catch – Aftermarket Replacement for Whirlpool, Kenmore, Maytag, GE, Hotpoint Product Overview This Door Catch is a replacement part for specific GE, Hotpoint dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly Replaces Part Numbers WE1M1011, PS3502777, AP5324728, WE01M0197, WE01X0889, WE01X0903, WE01X1032, WE1M187, WE1M197, WE1M536, WE1X1032, WE1X889, WE1X903. It provides a reliable fit and function similar to OEM components. Fixes the Following Issues Dryer door won’t stay closed Dryer doesn’t start Door pops open mid-cycle Worn or damaged door catch Compatible Brands Compatible with dryers made by Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, GE and Crosley. Suitable for many front-load and top-load residential models. Why Buy from Parts-O-Matic High-quality, durable replacement part Always Fast and Free U.S. shipping Easy to install – no special tools required Trusted by appliance repair professionals and DIYers

Read more less

6600JB3001C Refrigerator Dispenser Switch – Replacement for GE, LG and Kenmore Product Overview This Dispenser Switch is a replacement part for specific LG, Kenmore, GE refrigerator models. This switch is crucial for the functionality of the water and ice dispenser, as it activates the dispensing mechanism when the user presses the lever or button. The switch ensures that the refrigerator dispenses water or ice on demand, providing convenience and ease of use. Replaces Part Numbers This dispenser switch replaces part numbers 6600JB3001C, 1268245, 1395586, 6600JB3001B, 6600JB3001H, PD00025340, EAP3529276, AH3529276, EA3529276, AP4441530, PS3529276, WR23X10783, 2695743, WR23X10171, WR23X10224, AP5688654, PS8259956. Engineered to deliver OEM-level performance and compatibility. Compatible Brands Compatible with LG and Kenmore refrigerators manufactured by LG. Fits various French door, side-by-side, and bottom-freezer models with front panel dispensers. Fixes the Following Issues Water or ice dispenser not working Dispenser works only when pressed a certain way No power reaching water or ice components Intermittent or unresponsive dispenser control Why Buy from Parts‑O‑Matic Durable and reliable aftermarket replacement Fast and free U.S. shipping Simple to install with plug-in compatibility Trusted by appliance repair techs and homeowners

Read more less

W10428167 Dishwasher Pump and Motor Assembly Pump & motor assembly, circulation and drain are handled by this assembly Replaces Part Numbers: W10428167, 2024551, 3385003, 3385004, 8193511, 8193511A, 8283498, 8283502, AH3500988, EA3500988, AP5306229, PS3500988   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 Product Overview The XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 is designed to monitor water levels inside the dishwasher and prevent overfilling. This float switch detects rising water levels and signals the control system to stop filling, protecting your appliance from leaks and water damage. Quick Answer If your dishwasher is overfilling, not filling correctly, or leaking due to excess water, the 165256 float switch may be faulty. Replacing it restores proper water level control and prevents overflow issues. Replaces Part Numbers Replaces OEM part number: 00165256, 165256, 935359, EAP8697040, ABS10088, PD00035415, AH3439096, EA3439096, PS3439096, AP2802373, PS8697040. Compatibility This dishwasher float switch is compatible with select Bosch, Thermador, and other compatible dishwashers. Bosch Dishwashers Thermador Dishwashers Compatible European-style Dishwashers Always verify your appliance model number before ordering. Common Problems This Part Fixes Dishwasher overfilling Water leaking due to excess fill Incorrect water level detection Dishwasher not filling properly Key Features Monitors dishwasher water level Prevents overfilling and leaks High-quality aftermarket replacement Reliable and durable construction Product Specifications Part Number: 165256 Part Type: Dishwasher Float Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Level Control Troubleshooting Guide Dishwasher overfills → Faulty float switch Water keeps filling → Float switch stuck or failed Dishwasher won’t fill → Switch not detecting properly When Should You Replace This Float Switch? Replace this float switch if your dishwasher is overfilling, leaking, or not detecting correct water levels. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the float switch inside the tub area and install securely according to your dishwasher model. Related Parts Water Inlet Valve Dishwasher Float Assembly Control Board Frequently Asked Questions Will this float switch fit my dishwasher?This part fits many Bosch and compatible dishwashers. Always verify your model number. What does a float switch do?It monitors water levels and prevents overfilling inside the dishwasher. What are signs of a bad float switch?Overfilling, leaking, or improper water level control. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519 The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature. When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure. Quick Answer The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers. Common Problems This Part Fixes Dryer won't start at all Dryer runs but produces no heat Dryer stops mid-cycle and won't restart Timer advances but drum does not heat Dryer shuts off too soon before clothes are dry No continuity detected across fuse terminals during testing Replaces Part Numbers This thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (including Duet and Cabrio series) Kenmore / Sears dryers (including Elite series) KitchenAid dryers Maytag dryers (including Centennial and Neptune series) Roper dryers Estate dryers Inglis dryers Crosley dryers Amana dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Broad compatibility across 11 major appliance brands DIY-friendly repair — installs with basic hand tools in under 30 minutes Budget-friendly safety fix — one of the most common and least expensive dryer repairs Product Specifications Part Number 3392519 Part Type Dryer Thermal Fuse Condition Aftermarket Replacement Application Gas and Electric Dryers Opening Temperature 196°F (91°C) Length 2 inches Width 1/2 inch Terminal Size 3/16 inch (2 terminals) Resettable No — one-time use only, must be replaced when blown Location on Dryer Exhaust duct / blower wheel housing Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef Installation Notes ⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected. Frequently Asked Questions Will the 3392519 fit my dryer? This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering. What does a dryer thermal fuse do? The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced. How do I know if my thermal fuse is blown? Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced. Why did my thermal fuse blow? The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X10024 Genuine OEM Washer Water Valve Replaces Part Numbers: WH13X10024, WH13X0086, WH13X0087, WH13X10004, WH13X10019, WH13X86, WH13X87, AH1155105, EA1155105, OEM15444478, AP3861119, PS1155105. Description: This Water Inlet Valve is a Genuine OEM part for select GE washing machine models. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 316489403 Gas Oven Igniter The XPARTCO 316489403 is an aftermarket replacement gas oven igniter compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges, ovens, and stoves. The oven igniter is the component that lights the gas burner — when you set the oven to bake or broil, electricity flows through the igniter, heating it until it glows bright orange. This heat both ignites the gas and draws enough current to open the gas safety valve, releasing gas to the burner. When the igniter weakens with age, it may still glow but no longer pull enough current to open the safety valve — so the oven fails to light, takes a long time to heat, or heats unevenly. This is a flat-style, open-cage igniter. Electrical rating: 3.2–3.6 amps, 120V AC. Made of silicon carbide and ceramic for high heat resistance and long service life. Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; the lead and plug measure approximately 16" long. Includes the flat-style igniter assembly with bracket and leads/plug. It directly replaces 316489403, 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063. Important: the igniter element is fragile — handle it only by the bracket, never by the element itself. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 316489403 Gas Oven Igniter fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ovens that won't light, take too long to heat, heat unevenly, or where you smell gas because the igniter is too weak to open the safety valve. Flat-style open-cage igniter. 3.2–3.6A, 120V AC. Silicon carbide/ceramic. Overall 3-1/2"L x 1-3/4"W x 13/16"H, 16" lead. Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, PS2364063. Handle by the bracket only — the element is fragile. Common Problems This Part Fixes Oven won't light or heat at all — igniter too weak to open the gas safety valve Oven takes a long time to reach temperature — igniter glowing but drawing insufficient current Oven heats unevenly or undercooks food — weak or slow ignition Igniter glows but the burner never ignites — classic sign of a degraded igniter Igniter doesn't glow at all — burned out or open circuit (no power reaching the burner) Gas smell when the safety valve opens but the burner doesn't light Oven runs erratically or won't maintain temperature Igniter visibly cracked, broken, or with a damaged element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas oven igniter directly replaces the following OEM and cross-reference part numbers: 316489403, 5304508786, 7316489403, Model 501RB, AH2364063, EA2364063, EAP2364063, AFR16172, AP4433236, PD00000756, PS2364063. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: on some models this is the broil (upper) igniter, and the bake (lower) igniter is a different part — see the FAQ below on bake vs broil igniters. Compatibility This gas oven igniter is compatible with select gas ranges, ovens, and stoves from the following brands: Frigidaire gas ranges and ovens — including many Frigidaire Gallery models (LGGF, FGGF, FFGF series and related) Electrolux gas ranges and ovens (select models) Crosley gas ranges and ovens (select models) Gibson gas ranges and ovens (select models) Kelvinator gas ranges and ovens (select models) Tappan gas ranges and ovens (select models) White-Westinghouse gas ranges and ovens (select models) Ikea gas ranges and ovens (select Frigidaire-built models) Kenmore / Sears gas ranges and ovens (select Frigidaire-built models, including 790-series) Note: This igniter fits specific models — always verify against your appliance's model number before ordering. On ranges with two igniters (a bake igniter and a broil igniter), confirm which one you need (see the bake-vs-broil FAQ below). Contact our support team with your model number if you're unsure. Key Features Gas oven igniter — heats up to ignite the burner and draws current to open the gas safety valve Flat-style, open-cage design Resolves "won't light," "slow to heat," "uneven heating," "glows but won't ignite," and "gas smell" symptoms caused by a weak or failed igniter Electrical rating: 3.2–3.6 amps, 120V AC Silicon carbide and ceramic construction — high heat resistance and long service life Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; lead and plug approximately 16" long Includes the flat-style igniter assembly with bracket and leads/plug (some kits include ceramic wire nuts) Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 316489403 Part Type Gas Oven Igniter (Flat Style, Open Cage) Condition Aftermarket Replacement Application Gas Ranges, Ovens, and Stoves (Frigidaire platform) Amperage 3.2–3.6 Amps Voltage 120V AC Igniter Style Flat, open cage Overall Dimensions 3-1/2"L x 1-3/4"W x 13/16"H Ceramic Block 1.5" L Lead Length Approximately 16" Material Silicon carbide / ceramic / metal Color Almond / White / Gray Includes Igniter assembly with bracket and leads/plug Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Shut off the gas supply to the range at the shutoff valve and disconnect electrical power at the breaker before beginning any repair. After installation, if you smell gas at any point, leave the area immediately and contact your gas utility provider. If you're not comfortable working around gas components, have this repair done by a qualified appliance technician. Improper gas appliance repairs can cause fire, explosion, or carbon monoxide hazards. ⚠️ Handle the Igniter by the Bracket Only — The Element Is Fragile Disconnect power at the breaker and shut off the gas supply before beginning. Wear work gloves and safety glasses. The silicon carbide igniter element is extremely fragile and cracks easily — handle the new igniter only by its metal bracket, never by touching the element itself. Skin oils and any impact can shorten its life or break it. Locate the igniter: the bake igniter is beneath the oven floor panel (remove the oven racks, then the floor panel, and on some models the bottom drawer for access), while the broil igniter is mounted near the top of the oven cavity. Photograph the wiring connection before disconnecting. Disconnect the old igniter's wire leads at the connector (they're often joined with ceramic wire nuts). Remove the screws securing the old igniter bracket and lift it out. Install the new 316489403 by securing its bracket in the same position and orientation, then connect the wire leads (use the included or existing ceramic wire nuts — regular wire nuts can't handle the heat). Route the leads away from the burner flame. Restore gas and power. Test by setting the oven to bake (or broil, if that's the igniter you replaced) — the igniter should glow bright orange within a minute or so, and the burner should light within about 60–90 seconds. Tools needed: Nut driver, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions My igniter glows but the oven won't light — do I still need to replace it? Yes — this is actually the most common way an oven igniter fails, and it's counterintuitive. The igniter has two jobs: to get hot enough to ignite the gas, AND to draw enough electrical current to open the gas safety valve. As an igniter ages, it can still glow (so it looks like it's working) but weaken to the point where it no longer pulls enough current to open the safety valve — so no gas is released and the burner never lights. If your igniter glows orange but the burner doesn't light within about 90 seconds, the igniter is weak and needs replacement. A good rule of thumb: if it takes more than 90 seconds from glow to flame, the igniter is on its way out. Is the 316489403 the bake igniter or the broil igniter? This is an important distinction, and there's genuine confusion in the industry about it. On many Frigidaire gas ranges, the 316489403 is used as the broil (upper) igniter with an approximately 14–16" lead, while the bake (lower) igniter is a different part — 5304506545 (which superseded 316489404) — often with a shorter lead. However, some sources and parts diagrams list them differently or even reversed, and on some models the 316489403 serves the bake position. The safest approach: look up YOUR specific model number to confirm which igniter you need, and compare your old igniter's lead length to the replacement. If your old igniter's leads reach a connector far from the igniter (14–16"), the 316489403 with its 16" lead is likely correct. Contact our support team with your model number and we'll confirm. Why do I smell gas when I try to use the broiler? If you smell gas when the broiler's safety valve opens but the burner doesn't light, it usually means the igniter isn't getting hot enough (or drawing enough current) to ignite the gas that's being released — so raw gas escapes before shutting off. This points to a weak igniter. To confirm which part is at fault: with the gas off, do a voltage test at the oven safety valve on the broil side — you should read between 3.0 and 3.3 VAC. If the voltage is correct but the burner won't light, the igniter is the problem. If there's no proper voltage, or the burner tube has spider webs or debris blocking it, address those first. Also inspect the gas supply tube from the safety valve to the burner for damage or loose connections. Why do I need to handle the igniter so carefully? The igniter's heating element is made of silicon carbide, a material that's excellent at withstanding heat but is brittle and cracks easily from impact or flexing. Even touching the element with bare fingers can leave oils that create hot spots and shorten its life, and a small bump can crack it invisibly, causing premature failure. Always handle the new igniter by its metal bracket, never by the element or the ceramic block. When installing, be careful not to bump the element against the oven walls or burner. This care is the single biggest factor in whether your new igniter lasts years or fails early. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from silicon carbide and ceramic to match the electrical specifications (3.2–3.6A, 120V AC), flat open-cage style, dimensions (3-1/2"L x 1-3/4"W x 13/16"H, 16" lead), and ignition function of the original 316489403 gas oven igniter used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR2X7054CM Dishwasher / Refrigerator Push-on Nut Push on retainer clip. Used on GE dishwashers and refrigerators. Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

V-152-1C25 Micro Limit Switch Contact Type: SPDT 1NO 1NC Actuator Type: Long Straight 1" Hinge Lever Rating: 15A 125 250VAC Lever Length: 1" Rating: 15A,1/2HP, 125 250VAC; 0.6A,125VDC; 0.3A, 250VDC   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 6600JB3001E Refrigerator Dispenser Switch - Compatible with LG, Kenmore, GE Product Description Restore your refrigerator’s dispenser functionality with the XPARTCO 6600JB3001E Refrigerator Dispenser Switch. This high-quality replacement switch is designed for select LG, Kenmore, GE, and Hotpoint refrigerators, controlling the dispensing of ice or water when the lever is pressed. It ensures reliable operation at a cost-effective price, addressing issues like no dispensing or intermittent dispensing. Note: Includes one micro switch (16A 1/2HP, 125/250VAC, 10T150 μ1E4 ). Disconnect power before installation. Verify compatibility with your refrigerator model. Replaces part numbers: 6600JB3001E, 1268245, AH3529277, SZM-V16-2FA-53, EA3529277, AP4650818, PS3529277. Compatibility: Compatible with models including but not limited to: LG: LSC24971ST/00, LRSC21934SW Kenmore: 79571039010, 79571039011, 79578789801 GE, Hotpoint: (select models with WR23X10783 compatibility, verify part number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG, Kenmore, GE, and Hotpoint refrigerators with front panel dispensers. 🔧 Specifications: Micro switch, 16A 1/2HP, 125/250VAC, T130 5E4μ, 1/4" terminals. 💪 Reliable Performance: Ensures precise activation of ice and water dispensing. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves no dispensing or intermittent dispensing issues. Product Specification Part Number: XPARTCO 6600JB3001E Component Type: Refrigerator dispenser micro switch Material: Plastic housing, metal contacts Electrical Rating: 16A 1/2HP, 125/250VAC Mounting: Snap-in or screw-mounted, 1/4" terminals Operating Conditions: Suitable for refrigerator dispenser environments Compliance: UL listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator dispensing smoothly today! Add to cart now for a reliable fix!

Read more less