Search results for "cooking switch"

XPARTCO 3406107 Dryer Door Switch – Replaces WP3406107 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Ensure your dryer starts safely and operates correctly with the XPARTCO 3406107 Dryer Door Switch. This high-quality aftermarket replacement detects when the dryer door is closed, enabling the motor to run and heat to activate. A defective switch can prevent your dryer from starting or cause it to stop mid-cycle. Replacing it with this reliable XPARTCO switch restores normal operation and dependable performance. Replaces Part Numbers WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, PS11741701. Compatibility This replacement door switch fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.60902990, and Maytag MEDC200XW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Engineered to match OEM safety and electrical performance 🚪 Restores Start Function – Ensures dryer runs only when the door is fully closed 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ Quick Installation – Simple plug-in wiring and snap-in mounting 🛡️ Fixes Common Issues – Solves dryer not starting, shutting off mid-cycle, or running with door open 📐 Product Specification Part Number: 3406107 Component Type: Dryer Door Switch Assembly Material: Plastic body with metal actuator lever and 3-pin terminal Mounting: Snap-in installation behind front panel Electrical Rating: 15A / 125-250V AC Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and open the dryer door. Remove the top or front panel (depending on model). Unplug the old switch’s wire connectors. Press the locking tabs and remove the old switch. Install the new XPARTCO 3406107 switch, reconnect wires, and secure panels. Restore power and test dryer start function. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s start function — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA34-00041B Refrigerator Door Switch – Replacement for Samsung Product Overview The DA34-00041B Refrigerator Door Switch is an aftermarket replacement that controls interior lighting and signals the control board when the refrigerator or freezer door is open or closed. A malfunctioning switch can result in the light staying off or on, cooling fans not running correctly, or even door-related error codes. Replacing a faulty switch with this part helps restore normal operation and energy efficiency. Replaces Part Numbers This part replaces DA34-00041B, DA34-10110B, AP5957961, PS10061325. It is designed to meet OEM specifications for reliable fit and performance in Samsung-built refrigerators. Compatible Brands This door switch is compatible with refrigerators manufactured by Samsung and Kenmore (Samsung-built). It fits a wide range of French door, bottom freezer, and side-by-side models. Fixes the Following Issues Refrigerator light not turning on or off Cooling fan not operating when door closes Door-related error messages Inconsistent temperature regulation Why Buy from Parts‑O‑Matic Affordable and reliable aftermarket solution Fast and free U.S. shipping Easy to install with no special tools required Trusted by appliance repair professionals and DIYers

Read more less

WP74010750 Genuine OEM Whirlpool Oven Bake Element The WP74010750 is a Genuine OEM Whirlpool replacement oven bake element compatible with select Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges and ovens — particularly CE-series, JDS-series, and MES-series slide-in and freestanding ranges. The bake element is the lower heating element located at the bottom of the oven cavity. It provides the primary heat source for baking, roasting, and preheating. When the element coil burns through, the oven will not heat, will bake unevenly, or will trip the circuit breaker when the bake cycle is selected. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 2585W with push-on terminal ends (two 1/4" high-temp connectors). It measures approximately 23-5/8" wide x 15-3/8" long with 3-3/8" inserts. It directly replaces 74010750, 74003039, 7406P425-60, 1184162, WP74010750VP, ERB0750, AP6011209, PS11744404, and several additional cross-reference numbers. Installs in 15–20 minutes with basic hand tools. Quick Answer The WP74010750 Genuine OEM Whirlpool Oven Bake Element fixes electric ovens that won't heat, bake unevenly, or trip the circuit breaker during bake. 2585W, push-on terminal ends (two 1/4" high-temp connectors), 23-5/8"W x 15-3/8"L, 3-3/8" inserts. Genuine OEM. Compatible with Whirlpool CE, Jenn-Air JDS, Maytag MES series and related brands. Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, AP6011209, PS11744404. Common Problems This Part Fixes Oven produces no heat — bake element coil has burned through Oven takes much longer than normal to preheat Food baking unevenly — bottom of food undercooked while top is done Bake element not glowing red during the bake cycle Visible burn marks, blistering, holes, or breaks in the element coil Oven trips the circuit breaker when the bake cycle is selected — shorted element Burning smell during a bake cycle — arcing at a weak point in the element Replaces Part Numbers This bake element directly replaces the following OEM and cross-reference part numbers: WP74010750, 74010750, 1184162, 74003039, 7406P425-60, AP6011209, AWP47950, EAP11744404, PD00002565, PS11744404, WP74010750VP. Contact our support team with your model number if you need confirmation before ordering. Compatibility This bake element is compatible with select electric ranges and ovens from the following brands and series: Whirlpool electric ranges — CE35200, CE38800 and related CE-series models Jenn-Air electric ranges — JDS8850, JDS9860 and related JDS-series slide-in models Maytag electric ranges — MES5770 and related MES-series models KitchenAid electric ranges (select models) Amana electric ranges (select models) Kenmore / Sears electric ranges (select Whirlpool-built models) Magic Chef electric ranges (select models) Admiral electric ranges Norge electric ranges Roper electric ranges Note: Always verify your exact model number before ordering — bake elements are model-specific due to differences in dimensions and terminal configuration. The WP74010750 uses 1/4" push-on terminals and specific mounting dimensions that differ from other Whirlpool-family bake elements. If you are not sure this element is the right fit, contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for baking, roasting, and preheating in compatible electric ovens Rated 2585W — correct wattage for compatible CE, JDS, and MES series models Push-on terminal ends — two 1/4" high-temperature connectors for direct wire attachment Dimensions: approximately 23-5/8" wide x 15-3/8" long, with 3-3/8" inserts Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, and AP6011209 Compatible with Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number WP74010750 Part Type Oven Bake Element (Lower Heating Element) Condition Genuine OEM Application Electric Ranges and Ovens Wattage 2585W Terminal Type Push-on — two 1/4" high-temperature connectors Width Approximately 23-5/8 inches Length Approximately 15-3/8 inches Inserts 3-3/8 inches Compatible Brands Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Range or Turn Off Breaker Before Starting Disconnect power before beginning and allow the oven to cool completely. Open the oven door and remove all racks. The bake element is located at the bottom of the oven cavity. Remove the screws securing the element bracket to the rear oven wall — typically one or two Phillips screws at the back. Carefully pull the element forward toward the door to expose the two 1/4" push-on wire connectors behind the oven rear wall. Note the position of each wire before disconnecting — take a photo. Pull each wire connector off the element terminals by gripping the connector (not the wire) and pulling straight back. Connect the two wires to the new WP74010750 element's terminals, slide the element back into position, and secure the mounting screws. Restore power and run a bake cycle to confirm the element heats and glows red. Tools needed: Phillips screwdriver. Frequently Asked Questions How do I know if my bake element has failed? The clearest sign is an oven that does not heat, takes much longer than usual to preheat, or bakes food unevenly with the bottom undercooked. When the bake element is working, it should glow bright red during a bake cycle. If it does not glow at all, the element has failed. You can also visually inspect the element for burn marks, blistering, cracks, or a visible break in the coil. A multimeter continuity test will confirm failure — a working element shows continuity (resistance of approximately 10–100 ohms), while a failed element reads open circuit. If the element trips the circuit breaker when selected, the element coil has shorted to the metal housing — replace it immediately. What is the difference between WP74010750 and WP74003019? Both are Genuine OEM Whirlpool oven bake elements but for different model families and with different wattage ratings. The WP74010750 is rated 2585W and is used on CE, JDS, and MES-series electric ranges. The WP74003019 is rated 2800W and is used on a different set of models. They are not interchangeable — always verify your model number to confirm which element is correct for your oven before ordering. Is it normal for a bake element to arc or spark before it fully fails? Yes — it is not unusual for a bake element to arc or spark at a weak spot before the coil fully burns through. If you see sparking, arcing, or a bright flash from the element area, immediately turn off the oven and disconnect power. Do not use the oven again until the element has been replaced. An arcing element can damage the oven liner and, in rare cases, pose a fire risk. The good news is that once you replace the WP74010750 element, the oven should perform normally again. Are the wires interchangeable on the bake element terminals? On most electric range bake elements — including the WP74010750 — the two terminal wires are interchangeable. The bake element is a resistance heater with no polarity, so either wire can connect to either terminal and the element will heat correctly. However, it is good practice to photograph the original connection before disconnecting to ensure you reconnect in the same configuration, particularly if one wire is color-coded differently from the other. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same bake element installed in compatible Whirlpool, Jenn-Air, Maytag, and related brand electric ranges from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

WH44X10288 Washer Lid Lock and Switch Assembly Replaces Part Numbers: WH44X10288, 1974376, AH3496878, EA3496878, AP5270191, PS3496878. 120V, 60Hz, lid lock and switch assembly. Fits select GE laundry center. Description: This Door Latch Lid Lock is a replacement part for select GE washing machine models. It is designed to securely lock the washing machine's lid or door during operation, ensuring safety and preventing water from spilling during the wash cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

134101800 Washer Lid Lock Switch – Replacement for Frigidaire, Electrolux, Kenmore Product Overview This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. 120V, 60Hz, lid lock and switch assembly. Replaces Part Numbers This switch replaces part numbers 134101800, 131595100, 131675600, 3204390, 3204391, 3205646, 5303306138, 916791, AP2108159, PS648775. It matches original specifications for fit and performance in compatible top-load washers. Compatible Brands This lid lock switch is compatible with washers from Frigidaire, Electrolux, Kenmore, and Gibson. It fits many models built under these brands and used in U.S. and Canadian homes. Fixes the Following Issues Washer won’t start Lid lock error or flashing indicator Washer stops mid-cycle Broken or non-responsive lid switch Why Buy from Parts‑O‑Matic High-quality, tested aftermarket part Fast and free shipping across the U.S. Trusted by appliance repair pros and DIYers Easy returns and friendly customer support

Read more less

XPARTCO WH01X27954 Washer Lid Switch (Old Style) Product Overview The XPARTCO WH01X27954 Washer Lid Switch (Old Style) is designed to restore proper lid detection and washer operation. This high-quality replacement detects whether the washer lid is closed, allowing safe operation during wash and spin cycles. A broken or faulty switch can cause the washer not to start, stop mid-cycle, or fail to spin. Replacing it with this durable XPARTCO switch restores normal functionality and safety performance. Old-style GE lid switch (does not require harness replacement). Quick Answer If your washer will not spin, drain, or start properly, a faulty WH01X27954 lid switch may be the cause. Replacing this old style washer lid switch helps restore normal washer operation and cycle performance. Replaces Part Numbers Replaces OEM part number: WH08X32697, WH01X27954, WH08X31577, WH01X24114, WH01X26114, 290D1580P001, 290D1580P004, 290D1580P002, 290D1580P003, WH08X31577, AP7015047, PS16554755. Compatibility This washer lid switch is compatible with select GE, Hotpoint, and other compatible top-load washers that use the old style lid switch design. Example compatible models include (but are not limited to): GE GTW220ACK1WW GTW220ACK2WW GTW220ACK3WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW330ASK2WW GTW330ASK3WW GTW330ASK4WW GTW330ASKWW GTW335ASN0WW GTW335ASN2WW GTW335ASNWW GTW460AMJ0WW GTW460AMJ1WW GTW460AMJ2WW GTW460AMJ3WW GTW460AMJ4WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW335ASN0WW. GE Top-Load Washers Hotpoint Washers Old Style Lid Switch Applications Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting cycle Lid switch not detecting closed lid Key Features Designed for old style washer lid switch applications Helps restore safe and proper washer operation High-quality aftermarket replacement Durable construction for reliable performance Product Specifications Part Number: WH01X27954 Part Type: Washer Lid Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Top-Load Washers Style: Old Style Troubleshooting Guide Washer fills but does not spin → Lid switch may be faulty Washer will not start cycle → Lid switch may not detect closed lid Washer stops before spin cycle → Defective lid switch can interrupt operation When Should You Replace This Lid Switch? Replace this lid switch if your washer does not start, spin, or drain properly, or if the switch no longer detects when the lid is closed. Installation Notes ⚠️ Disconnect power before installation. Access the lid switch area according to your washer design and install the replacement securely. Refer to your appliance manual if needed. Related Parts Washer Lid Strike Washer Timer Washer Door or Lid Lock Components Frequently Asked Questions Will this lid switch fit my washer?This switch fits select GE and compatible washers that use the old style lid switch. Always verify your model number. What does a washer lid switch do?It detects whether the washer lid is closed so the machine can operate safely. What are signs of a bad lid switch?Common signs include the washer not spinning, not starting, or stopping before the cycle completes. Is this the old style version?Yes, this listing is for the old style WH01X27954 washer lid switch. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality aftermarket parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO 3406108 Dryer Door Switch - Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO 3406108 Dryer Door Switch. This door switch is designed for select Whirlpool, Kenmore, Maytag, and other dryer models, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch with 2 wire leads and a two-prong plug. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP3406108, 3406108, PD00029356, EAP11741702, PS11741702, AP6008562.  Compatibility: Compatible with models including but not limited to: Whirlpool: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. Kenmore: 11060012000, 11060022010, 11060232000 Maytag: MEDC400VW0, AED4475TQ1 Other brands: Select models requiring 3406108 (e.g., Amana, Crosley, Roper) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Roper dryers requiring 3406108. 🔥 Specifications: Replacement dryer door switch, 2 wire leads, two-prong plug, 120-240V, 50-60Hz, 11A, 1/3HP. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop when door is opened. Product Specification Part Number: XP3406108 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: Two-prong plug with 2 wire leads Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO W10810403 (OE) Washer Lid Switch Assembly – Compatible with Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana Washers Product Description Keep your washer running safely and reliably with the XPARTCO W10810403 Washer Lid Switch Assembly. This replacement part ensures the washer only operates when the lid is securely closed, preventing unsafe operation. A faulty lid switch can cause your washer to not start, stop mid-cycle, or fail to drain. Replacing it with this high-quality part restores dependable performance. What is OE ?:  “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. They offer identical fit and function to OEM (Original Equipment Manufacturer) components but are typically sold under independent brands like XPARTCO for better affordability. Replaces Part Numbers W10810403, 4283179, W10648012, W10787878, W10810403VP, PD00028176, EAP11722981, AP5984435, PS11722981. Compatibility This washer lid switch assembly is compatible with select Whirlpool, Kenmore, Maytag, Crosley, Roper, and Amana top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW4800BQ1, Kenmore 110.20222511, and Maytag MVWC415EW1. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana top-load washers 🔒 Safe Operation – Ensures washer won’t run with lid open 💰 Cost-Effective Alternative – OEM-equivalent performance at a lower price 🛠️ Easy Installation – Only requires a Phillips screwdriver, installs in 10–20 minutes 🛡️ Fixes Common Issues – Resolves washers not starting, stopping mid-cycle, or failing to drain 📐 Product Specification Part Number: W10810403 Component Type: Washer Lid Switch Assembly Material: High-durability plastic + electrical connectors Mounting: Direct replacement, top panel mount Operating Conditions: Designed for standard residential washer use Compliance: OEM-equivalent quality standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver ⚠️ Safety First: Always unplug the washer before starting repairs to avoid electrical shock. Steps: Unplug washer and locate lid switch under the top panel. Remove screws securing the control panel and release clips. Disconnect the wire harness from the old switch. Remove the old switch and install the new one in its place. Reconnect wiring, secure panel, and test the washer. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your washer’s performance today — Add to Cart Now for a safe, budget-friendly fix!

Read more less

XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers Product Description Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts. Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083. Compatibility: Compatible with models including but not limited to: Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS Other brands: Select models requiring DC96-01703G Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G. 🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA). Product Specification Part Number: XPDC96-01703G Component Type: Washer water level pressure switch Material: Durable plastic housing with metal contacts Terminal Type: Electrical connector. Operating Conditions: Suitable for high-humidity washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

WPW10242957 Range Genuine OEM Surface Element Radiant Surface Element Radiant surface element, 2000 watts Replaces Part Numbers: WPW10242957, W10242957, 1873054, 4343098, 8053622, 8272568, 8523695, OEM24070458, AP6017614, PS11750913. Description: This Radiant Surface Element is an OEM replacement part for specific Whirlpool, Maytag electric ranges and cooktops.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less