00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer
The 00770657 is a genuine Bosch OEM cutlery drawer — a dedicated third-rack silverware caddy that sits in the upper interior of the dishwasher tub, above the top rack, on select Bosch dishwashers equipped with a third rack add-on compartment. Rather than loading silverware into a basket down in the lower rack, this drawer holds forks, spoons, and knives flat in their own dedicated level, laid out individually with room around each piece so water and detergent can reach every surface. It rides on durable rollers along rails built into the tub, sliding smoothly in and out for loading and unloading, and its position at the top of the tub gives it a clear, unobstructed line to the upper spray arm for targeted cleaning.
The tray and support grid inside the drawer are open enough to let water flow freely through while still keeping utensils separated and organized. Because it's a lightweight tray sitting in a hot, wet, chemically active environment for years, common failure points include a metal frame that rusts through and eventually collapses under its own weight, plastic that becomes brittle or begins visibly disappearing from years of heat exposure, and dividers that crack or break, letting silverware jumble together. It directly replaces AP5788109, 00689507, 3279853, and PS8747441. As a genuine OEM part, the 00770657 is manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The 00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer fixes Bosch (and compatible Thermador, Gaggenau, and select Kenmore) dishwashers with a third-rack cutlery drawer that has rusted through, has cracked or broken dividers, has become gummy or sticky and won't slide smoothly, or has cracks exposing silverware to the heating element below. Rides on rollers for smooth in-and-out extension. Replaces AP5788109, 00689507, 3279853, PS8747441. This is the roller-equipped cutlery drawer — a similar-looking companion part, 00770656, is a different drawer design without rollers, so double-check which one your dishwasher uses.
Common Problems This Part Fixes
Metal frame of the cutlery drawer rusted through or visibly corroding
Drawer frame collapsing or sagging under the weight of silverware
Missing or broken dividers letting silverware commingle instead of staying separated
Drawer glides that have become gummy or sticky from food residue buildup, obstructing smooth movement
Cracks or holes in the drawer exposing silverware to direct contact with the heating element
Plastic that has become brittle, discolored, or is visibly disappearing after years of heat exposure
Silverware not getting fully clean due to poor spray coverage from a warped or damaged drawer
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher cutlery drawer directly replaces the following OEM and cross-reference part numbers:
00770657, AP5788109, 00689507, 3279853, ABS12031, EAP8747441, PD00043732, PS8747441
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cutlery drawer is compatible with select Bosch dishwashers equipped with a third rack add-on compartment, and is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers configured with a triple-rack setup, including model numbers such as:
SHE68T52UC, SHE68T55UC, SHE68T56UC, SHE68TL5UC
SHE863WF5N, SHE863WF6N
SHP65T56UC, SHP65TL2UC
SHV68T53UC, SHV68TL3UC, SHV863WD3N
SHVM63W53N, SHXM63W55N, SHXM63WS5N
Each of these models spans multiple production suffixes (such as /01, /02, /07, and /09) — check your full model and production number for exact confirmation.
Note — check for rollers: This drawer rides on rollers. A similar-looking companion part, 00770656, is a separate cutlery drawer design used on other Bosch/Thermador/Gaggenau models without the roller mechanism. The two are not interchangeable. Check whether your existing drawer slides on visible rollers before ordering, and always verify your full model and production number. Contact our support team with your model number if you're unsure which drawer fits your dishwasher.
Key Features
Genuine Bosch OEM part — factory-specified frame, grid, and roller mechanism
Dedicated third-rack cutlery drawer positioned above the top rack for optimal spray-arm targeting
Resolves "rusted frame," "broken dividers," "sticky glides," and "cracked drawer" symptoms caused by wear and corrosion
Multi-level basket layout keeps silverware separated for full surface exposure to wash spray
Rides smoothly on rollers for easy extension and retraction when loading and unloading
Open tray and support grid design allows water and detergent to flow through freely
Direct drop-in replacement — no tools required, simply slides into place on existing rails
Replaces AP5788109, 00689507, 3279853, and PS8747441
Compatible with Bosch, Thermador, Gaggenau, and select Kenmore third-rack dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
00770657
Part Type
Dishwasher Third-Rack Cutlery / Silverware Drawer
Condition
Genuine OEM
Brand
Bosch
Location
Upper interior of the tub, above the top rack
Mounting
Rides on rollers along built-in tub rails
Design
Multi-level basket grid with open tray for water flow
Repair Difficulty
Very Easy — no tools required
Quantity
1 cutlery drawer
Compatible Brands
Bosch, Thermador, Gaggenau, select Kenmore
Installation Notes
This is one of the simplest repairs in the entire dishwasher — no tools, no wiring, and no water lines to disconnect. Open the dishwasher door fully. Locate the existing cutlery drawer at the top of the tub, above the upper rack, and slide it forward and out along its rails until it clears the cabinet. Line up the new 00770657 drawer with the same rollers and rails, and slide it in until it seats fully at the back of the tub. Close the door and run a cycle to confirm the drawer sits securely and doesn't rattle or shift during operation.
Frequently Asked Questions
Does my drawer use rollers, or is it the other style?
Slide your existing drawer out partway and look underneath or along the sides — this 00770657 drawer rides on visible roller wheels along the tub rails. If your drawer instead has a simpler glide track with no rollers, you likely have the companion part, 00770656, which is a different design used on other models. The two aren't interchangeable, so it's worth confirming before ordering.
My drawer's metal frame has rusted through. Is that just cosmetic, or should I replace it?
It's worth replacing rather than living with it. Once the metal frame starts rusting through, it typically continues to weaken and can eventually collapse under the weight of loaded silverware, sometimes suddenly. Customers who've dealt with this describe the original frame rusting to the point of failure over time — replacing it before it fully gives out avoids a mid-cycle collapse and keeps your utensils properly organized and exposed to the wash spray.
Do I need any tools to install this?
No. This is a genuinely tool-free repair — slide the old drawer out along its rails, then slide the new one in until it seats. Customers consistently describe this as one of the easiest dishwasher parts to swap.
I see cracks or holes in my drawer near the bottom. Is that a safety concern?
It can be, depending on where the damage is. If cracks or holes are positioned where silverware could shift down and make direct contact with the dishwasher's heating element, that's worth addressing rather than ignoring, since it can affect both the cleaning process and the condition of your utensils over repeated cycles. Replacing a cracked or holed drawer resolves this.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original roller mechanism, basket grid layout, and dimensions of the cutlery drawer originally installed in your third-rack-equipped Bosch, Thermador, Gaggenau, or compatible Kenmore dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
(5 Pack) XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm
Product Description
Protect high-current electrical circuits with the XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm. This time-delay (slow-blow) fuse is designed to tolerate temporary inrush currents while providing dependable over-current protection for appliances, industrial equipment, and power supply systems.
The ceramic body construction offers superior heat resistance and arc containment compared to glass fuses, making it ideal for high-power applications. If excessive current flows, the fuse safely interrupts the circuit to prevent component damage or fire hazards.
Replaces Part Numbers
XP25A-SB, 25A 250V 6.35x32mm Slow Blow Fuse, MDL-25 equivalent style
Compatibility
This 25A slow-blow ceramic fuse is commonly used in:
Microwave ovens
Power supply units
Industrial control equipment
HVAC systems
Amplifiers and high-current appliances
Always verify amperage (25A), voltage rating (250V), and size (6.35 x 32 mm / 1/4" x 1-1/4") before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Slow Blow (Time Delay) – Handles temporary startup surges
⚡ 25 Amp Rating – Protects high-current circuits
🔥 Ceramic Body Construction – Enhanced heat and arc resistance
📏 Standard Size – 6.35 mm x 32 mm (1/4" x 1-1/4")
🛡️ Reliable Circuit Protection – Prevents overload damage
📐 Product Specification
Part Number: XP25A-SB-5PK
Type: Ceramic Line Fuse
Blow Type: Slow Blow (Time Delay)
Current Rating: 25 Amps
Voltage Rating: 250V
Size: 6.35 mm x 32 mm (1/4" x 1-1/4")
Application: Over-current protection
Quality Level: Aftermarket replacement
🛠️ Installation Notes
Tools Needed: Fuse puller or insulated pliers
⚠️ Safety First: Disconnect power before replacing any fuse to prevent electrical shock.
Basic Steps:
Turn off and unplug the device.
Locate the fuse holder.
Carefully remove the blown fuse.
Install the new XP25A-SB 25A slow-blow fuse.
Restore power and test operation.
⏱️ Time Required: Under 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance & Electrical Parts Supplier
🔄 30-Day Return Policy
Protect your equipment with dependable over-current protection — Add to Cart Now for a reliable replacement fuse!
XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers
Product Description
Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly.
Replaces Part Numbers
6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422.
Compatibility
This replacement rotor position sensor fits select LG and Kenmore front-load washers.
Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Aftermarket Replacement – Designed to match OEM performance and precision
Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing
Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price
Plug-and-Play Installation – No wiring modification required
Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors
Product Specification
Part Number: 6501KW2002B
Component Type: Washer Rotor Position Sensor (Hall Sensor)
Material: Durable printed circuit board with reinforced plastic housing
Mounting: Direct-fit installation on stator assembly
Operating Conditions: Rated for high-humidity, high-vibration washer environments
Compliance: Built to OEM-equivalent quality standards (not OEM)
Installation Notes
Tools Needed: 10 mm socket wrench, Phillips screwdriver
⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock.
Steps:
Disconnect power and remove the rear access panel.
Unscrew the rotor bolt and carefully remove the rotor assembly.
Locate and unplug the old sensor from the stator.
Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs.
Reconnect the wiring harness, reinstall the rotor, and secure the panel.
Restore power and run a spin test to verify correct operation.
⏱️ Time Required: 20–25 minutes
Shop With Confidence
Trusted Appliance Parts Supplier
30-Day Return Policy
Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!
XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F) – Normally Closed – Universal Microwave Safety Cutoff
Product Description
Protect your microwave from extreme overheating with the XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F), Normally Closed. This high-temperature safety device is designed to remain closed (conductive) during normal operation and open permanently when internal temperatures exceed 180℃, immediately cutting power to prevent serious damage or fire risk. A tripped thermal cut-off can cause the microwave to lose power or stop heating. Replacing it with the correctly rated NC fuse restores safe and reliable operation.
Replaces Part Numbers
XPMTC-180, MTC-180, Microwave Thermal Fuse 180C NC, 356F Normally Closed Thermal Cutoff, WB24X29270, 4586233, PD00045446, EAP12170419, KSD1 BR1 180, AP6262395, PS12170419, 6930W1A003X, 1365203, AH3530468, EA3530468, PD00001857, AP4443816, PS3530468.
Compatibility
This normally closed microwave thermal cut-off fuse is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 180℃ (356°F) NC thermal cutoff.
Commonly used near the magnetron, high-heat zones, or cavity protection points.
Always verify temperature rating and contact type before ordering.Contact our support team if you’re unsure.
🔍 What’s the Difference Between NC and NO Thermal Cut-Offs?
Normally Closed (NC): Circuit is closed during normal operation and opens permanently when the rated temperature is reached.👉 Most microwave thermal cut-offs are NC.
Normally Open (NO): Circuit is open during normal operation and closes only when overheated (used in limited designs).
⚠️ Installing the wrong type (NC vs NO) may cause the microwave not to run or fail to protect against overheating.
✅ Key Features
🔄 Aftermarket Replacement – Built to OEM-equivalent safety specifications
🌡️ 180℃ (356°F) Rating – Designed for high-temperature protection zones
🔁 Normally Closed (NC) – Conducts power during normal operation
🛡️ Critical Safety Component – Prevents overheating and fire hazards
💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut-offs
📐 Product Specification
Part Number: XPMTC-180
Component Type: Microwave Thermal Cut-Off Fuse
Temperature Rating: 180℃ (356°F)
Contact Type: Normally Closed (NC)
Function: One-time safety cutoff
Material: Heat-resistant metal body
Application: Magnetron or high-heat cavity temperature protection
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, insulated pliers
⚠️ Safety First:Unplug the microwave before servicing. Microwaves contain high-voltage components—allow capacitors to discharge before handling internal parts.
Basic Steps:
Disconnect microwave power.
Remove the outer cabinet or access panel.
Locate the thermal cut-off near the magnetron or high-heat area.
Disconnect wiring and remove the failed fuse.
Install the new XPMTC-180 (NC) thermal cut-off in the same position.
Reassemble the microwave and restore power.
Test operation.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore microwave safety under extreme heat conditions — Add to Cart Now for a dependable, budget-friendly repair!
XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm
Product Description
Protect high-current electrical circuits with the XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm. This time-delay (slow-blow) fuse is designed to tolerate temporary inrush currents while providing dependable overcurrent protection for appliances, industrial equipment, and power supply systems.
The ceramic body construction offers superior heat resistance and arc containment compared to glass fuses, making it ideal for high-power applications. If excessive current flows, the fuse safely interrupts the circuit to prevent component damage or fire hazards.
Replaces Part Numbers
XP25A-SB, 25A 250V 6.35x32mm Slow Blow Fuse, MDL-25 equivalent style
Compatibility
This 25A slow-blow ceramic fuse is commonly used in:
Microwave ovens
Power supply units
Industrial control equipment
HVAC systems
Amplifiers and high-current appliances
Always verify amperage (25A), voltage rating (250V), and size (6.35 x 32 mm / 1/4" x 1-1/4") before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Slow Blow (Time Delay) – Handles temporary startup surges
⚡ 25 Amp Rating – Protects high-current circuits
🔥 Ceramic Body Construction – Enhanced heat and arc resistance
📏 Standard Size – 6.35 mm x 32 mm (1/4" x 1-1/4")
🛡️ Reliable Circuit Protection – Prevents overload damage
📐 Product Specification
Part Number: XP25A-SB
Type: Ceramic Line Fuse
Blow Type: Slow Blow (Time Delay)
Current Rating: 25 Amps
Voltage Rating: 250V
Size: 6.35 mm x 32 mm (1/4" x 1-1/4")
Application: Overcurrent protection
Quality Level: Aftermarket replacement
🛠️ Installation Notes
Tools Needed: Fuse puller or insulated pliers
⚠️ Safety First: Disconnect power before replacing any fuse to prevent electrical shock.
Basic Steps:
Turn off and unplug the device.
Locate the fuse holder.
Carefully remove the blown fuse.
Install the new XP25A-SB 25A slow-blow fuse.
Restore power and test operation.
⏱️ Time Required: Under 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance & Electrical Parts Supplier
🔄 30-Day Return Policy
Protect your equipment with dependable overcurrent protection — Add to Cart Now for a reliable replacement fuse!
Genuine OEM WPW10605427 Washer Drain Pump
The Genuine OEM Whirlpool WPW10605427 is the washer drain pump for select Whirlpool, Maytag, Amana and Crosley washers. The drain pump removes wastewater from the washer during the drain portion of the cycle. When it fails, the washer may not drain, may leak near the pump, may make unusual noise, or may pump but not spin.
This is the original Whirlpool part, not an aftermarket equivalent. It replaces many earlier Whirlpool pump numbers, so the new pump may look different from your original. It is sold individually, without accessories or wire harnesses. Check your model number before ordering.
Quick Answer
The Genuine OEM WPW10605427 Drain Pump replaces the drain pump on a compatible Whirlpool, Maytag, Amana or Crosley washer when it has failed. Replaces W10605427, W10425238 and several other Whirlpool pump numbers. Classic symptoms: the washer won't drain, leaks, or makes unusual noise.
Common Problems This Part Fixes
Washer won't drain, or keeps water after the cycle
Water leaking near the pump
Unusual noises during draining
Washer pumps but won't spin
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump replaces or supersedes the following part numbers:
WPW10605427 replaces WPW10425238, W10425238, W10605427, W10799064, W10799065, W10903216, W10918044, W10365896, B40-3A, AP6023357, AWP51154, EAP11756700, PD00038328, PS11756700
If your old pump shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This drain pump is listed for Whirlpool, Maytag, Amana and Crosley washers, including these examples:
Maytag MHW3000BW2, MHW3500FW0, MHW4300DC0, 7MMHW5500FW0
Whirlpool WFW87HEDC0, WFW95HEDC0, 7MWFW75HEFW0, 7MWFW90HEFW0
Crosley CFWH4084GW0
Note: The models above are a small sample of about 30 that retailers list, not a full list. Similar-looking pumps can differ in size and shape, so check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool part, not an aftermarket equivalent
Pumps wash water out of the washer during the drain cycle
Replaces many earlier Whirlpool drain pump numbers
Sold individually
Product Specifications
Part Number
WPW10605427
OEM Part Number
WPW10605427
Part Type
Washer Drain Pump
Condition
Genuine OEM
Manufacturer
Whirlpool
Quantity
1 Pump
Application
Select Whirlpool, Maytag, Amana & Crosley Washers
Installation Notes
⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear work gloves. The pump is at the bottom of the washer, and installation involves partially disassembling it, so moving the washer away from the wall helps. Remove the bottom or back panel and drain any remaining water. Disconnect the drain hose and electrical plug, remove the mounting bolts, and take out the old pump. Fit the new pump, reconnect the hose and plug, and refit the panel. Restore power and water and run a drain cycle, checking for leaks.
Frequently Asked Questions
My washer won't drain. Is this the part I need?
It can be, but a clogged hose or filter, or other parts, can cause the same symptom. Check for blockages first, and test the pump for continuity with a multimeter before replacing it. If the pump runs continuously, the water level switch may be the cause, so check that as well.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Whirlpool, not an aftermarket equivalent.
Will the pump look the same as my old one?
Not necessarily. This pump replaces many earlier Whirlpool pump numbers, so it can look different from the original while still being the correct replacement. Match the part number and your model number.
Will this fit my washer?
It is listed for about 30 Whirlpool, Maytag, Amana and Crosley models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W11210459 Washer Water Inlet Valve
The XPARTCO W11210459 is an aftermarket replacement washer water inlet valve assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper top-load washers in the WTW4xxx, WTW5xxx, MVWC4xx, MVWC5xx, NTW, and related series. The water inlet valve is a solenoid-operated valve mounted on the back of the washer that controls the flow of water from the household supply lines into the washer tub. When the control board calls for water during a fill or rinse cycle, it energizes the valve's solenoid coil to open the valve and allow water to flow in. When the correct water level is reached, the solenoid de-energizes and the valve closes.
When the water inlet valve fails, the washer may not fill with water at all, fill too slowly, fill with an incorrect temperature, overfill, or drip water into the tub when it should be closed. This valve assembly directly replaces W10701459, W10838319, W10869799, W11025984, W11038711, W11210459VP, AP6329217, and PS12349267. Installs in 15–20 minutes with basic hand tools.
Quick Answer
The XPARTCO W11210459 Washer Water Inlet Valve fixes Whirlpool-family top-load washers that won't fill, fill slowly, fill with the wrong water temperature, overfill, or drip water into the tub between cycles. Compatible with Whirlpool WTW4xxx/WTW5xxx, Maytag MVWC4xx/MVWC5xx, Kenmore, Amana NTW, Crosley, Inglis, and Roper top-load washers. Replaces W10701459, W10838319, W10869799, W11025984, W11038711, AP6329217, PS12349267.
Common Problems This Part Fixes
Washer not filling with water at all when a cycle is started
Washer filling very slowly — taking much longer than normal to reach the correct water level
Washer filling with only cold water on a warm or hot cycle — or only hot on a cold cycle
Washer overfilling or filling continuously — valve stuck open
Water dripping or trickling into the tub when the washer is not running
Water leaking from the back of the washer near the valve body
Washer not advancing past the fill portion of the cycle
Replaces Part Numbers
This water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, AWP43369, PD00042885, EAP12349267, AP6329217, PS12349267.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select top-load washers from the following brands and series:
Whirlpool top-load washers — WTW4616, WTW4715, WTW4810, WTW4815, WTW4816, WTW4850, WTW4855, WTW4915, WTW4950, WTW4955, WTW5000 series and related models
Maytag top-load washers — MVWC215, MVWC415, MVWC416, MVWC465, MVWC555 series and related models
Kenmore / Sears top-load washers — 110 series (Whirlpool-built models)
Amana top-load washers — NTW4516, NTW4655 series and related models
Crosley top-load washers (select models)
Inglis top-load washers (select models)
Roper top-load washers (select models)
Note: Always verify your exact model number before ordering. The W11210459 is a specific-fit valve — not universal. Contact our support team if you need confirmation before ordering.
Key Features
Solenoid-operated valve — opens and closes on command from the control board to deliver the correct amount of hot and cold water during wash and rinse cycles
Complete valve assembly — direct plug-in replacement for compatible models
Resolves not-filling, slow-filling, wrong-temperature, overfill, and drip-when-off symptoms
Replaces W10701459, W10838319, W10869799, W11025984, W11038711, and AP6329217
Compatible with Whirlpool WTW4xxx/WTW5xxx, Maytag MVWC series, Amana NTW series, Kenmore 110 series, Crosley, Inglis, and Roper top-load washers
Top-load washer application — not for Whirlpool front-load models
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–20 minutes with basic hand tools
Product Specifications
Part Number
W11210459
Part Type
Washer Water Inlet Valve Assembly
Condition
Aftermarket Replacement
Application
Top-Load Washers
Valve Type
Solenoid-operated water inlet valve
Compatible Series
WTW4xxx, WTW5xxx, MVWC4xx, MVWC5xx, NTW, Kenmore 110
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer — the external supply hoses connect to the inlet ports and internal hoses route water into the tub. Photograph all wire harness connections and hose routing before disconnecting anything. Use pliers to loosen the hose clamps and disconnect the internal hoses. Unscrew the mounting screws holding the valve to the washer cabinet and disconnect the wire harness. Remove the old valve and install the new W11210459 in the same position. Reconnect the wire harness, internal hoses with clamps, and mounting screws. Reconnect the external supply hoses, restore water and power, then run a fill cycle and check for leaks. Tools needed: Phillips screwdriver, pliers.
Frequently Asked Questions
What is the difference between the W11210459 and the W10683603 water inlet valves?
Both are Whirlpool-platform top-load washer water inlet valves, but they are different assemblies for different model generations and are not interchangeable. The W10683603 (WPW10683603) is a larger dual-valve assembly with an integrated thermistor and vacuum break, used on older Whirlpool-family top-load models. The W11210459 is a newer valve assembly used on more recent Whirlpool WTW4xxx/WTW5xxx and Maytag MVWC series top-load washers. Always use your specific model number to confirm which valve is correct for your washer before ordering.
How do I know if the water inlet valve has failed?
Common signs of a failed water inlet valve are the washer not filling with water, filling very slowly, filling only on one temperature setting, overfilling, or water dripping into the tub when the washer is off. You can test the valve's solenoid coils with a multimeter — each coil should show a resistance reading (typically 200–500 ohms) rather than open circuit. A coil reading open circuit has failed. Before testing the valve, check that the household water supply is fully open, the fill hoses are not kinked, and the inlet screens inside the valve ports are not clogged with mineral deposits.
What are the small screens inside the valve inlet ports for?
The small mesh screens inside the hot and cold water inlet ports of the valve are sediment filters that prevent mineral deposits and debris from the household water supply from reaching the valve seats and solenoid mechanisms. Over time — especially in areas with hard water — these screens can become clogged with mineral buildup and restrict water flow, causing the same slow-fill symptoms as a failed valve. Before replacing the valve, remove and inspect the inlet screens. If they are clogged, clean them with a soft brush and white vinegar or replace them. If cleaning the screens does not restore normal fill speed, the valve itself needs replacement.
My washer fills with only cold water — is the water inlet valve the cause?
Filling with only cold water when a warm or hot cycle is selected usually points to the hot water solenoid coil having failed. Each solenoid controls one temperature port independently — a failed hot coil means only the cold port opens. Test both solenoid coils with a multimeter as described above. Also check that your household hot water supply valve is fully open and that hot water is reaching the back of the washer in the supply hose before assuming the valve has failed.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the specifications and performance of the original W11210459 water inlet valve assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WE4X800 Dryer Genuine OEM Thermostat
Replaces Part Numbers: WE4X800, 2285, AH268245, EA268245, ET800, WE04X0730, WE04X0800, WE4X730, OEM10477750, AP2619437, PS268245.
Description: This Thermal Cut-Off Kit is a Genuine OEM part for specific GE dryer models. This safety kit is designed to protect the dryer from overheating by interrupting the heat source when the dryer air temperature reaches dangerously high levels.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 5220FR2008C Washer Water Valve
The XPARTCO 5220FR2008C is an aftermarket replacement water inlet and dispenser valve assembly for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's water source and to the washer's solenoid wiring, controlling exactly how much water enters the tub and ensuring the correct fill level for each cycle. The assembly has 1 inlet and 4 outlets.
Rated 120V, 60Hz. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer continuing to fill even after it should be full, filling slowly, overfilling, or leaking water into the drum when the washer is off. On some LG models, this can also trigger an FE error code specifically tied to the fill process. It directly replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
Quick Answer
The XPARTCO 5220FR2008C Washer Water Valve fixes LG and select Kenmore front-load washers that keep filling past full, fill slowly, overfill, or leak water into the drum when off — sometimes accompanied by an FE error code. 120V, 60Hz, 1 inlet, 4 outlets. Replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429. Some LG steam washers use this valve alongside a separate hot water valve — if only one side is failing, you may only need to replace the specific valve at fault rather than the whole group.
Common Problems This Part Fixes
Washer continues filling with water even after it should be full
Washer filling slowly
Washer overfilling
Water leaking into the drum when the washer is turned off
FE error code displayed during the fill portion of the cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform.
Note: LG uses several visually similar water valves across its washer lineup, including 5220FR2006H and 5221ER1003S. This part is also closely related to our 5220FR2008C cold water inlet valve listing — some model listings note that either may fit depending on the exact production run, but they are separate part numbers. Always confirm your exact part number — comparing your old valve's printed number and photo against the listing is the most reliable way to avoid ordering a similar-looking but incorrect valve. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement water inlet and dispenser valve assembly
Resolves "won't stop filling," "fills slowly," "overfills," "leaks when off," and "FE error code" symptoms
1 inlet, 4 outlets
Rated 120V, 60Hz
Sold individually
Direct drop-in replacement — matches the original mounting and hose connections
Replaces 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
Compatible with LG and select Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP5220FR2008C
OEM Part Number
5220FR2008C
Part Type
Washer Water Inlet & Dispenser Valve Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers
Voltage
120V
Frequency
60 Hz
Inlets / Outlets
1 inlet, 4 outlets
Weight
Approx. 0.60 lbs
Package Dimensions
5.12" x 4.69" x 3.98"
Repair Difficulty
Easy to Moderate
Quantity
1 valve (sold individually)
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access on most LG front-load washers requires removing the top cover to reach the water valve assembly and its electrical connections and hoses. On models with multiple valves (some LG steam washers use one separate hot water valve plus a group of cold water valves), identify specifically which valve is failing before removing anything — check your old valve's printed part number and compare it against a reference photo, since several LG valves look very similar. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and hose from the failing valve, remove its mounting screws, and pull it free. Install the new 5220FR2008C in the same position, reconnect the hose and electrical connector fully, and secure the mounting screws. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking or error codes. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
My washer shows an FE error code. Is this the valve I need?
Possibly. One customer reported an FE error appearing while the machine was still "filling," which pointed to one of the hot or cold water valves not working correctly. If your FE error consistently appears during the fill portion of the cycle, this valve is a reasonable place to start troubleshooting.
My washer has more than one water valve. Do I need to replace all of them?
Not necessarily. Some LG steam washers use a separate hot water valve plus a group of valves fed from the cold water main, and it's common for only one specific valve in that group to actually be bad. One customer confirmed this exact setup, testing and replacing only the single failing valve rather than the entire group, which resolved their issue.
How do I make sure I'm ordering the correct valve, since several look similar?
Check the part number printed directly on your old valve and compare it, along with a photo if available, against the listing before ordering. One customer specifically noted that several LG valves looked alike, and having a clear reference photo was what let them positively identify the correct replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the solenoid design, inlet/outlet configuration, and electrical rating of the original 5220FR2008C valve used in compatible LG and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR50X60 Refrigerator Genuine OEM Defrost Thermostat – For GE, Hotpoint, and Kenmore
Product Overview
The WR50X60 Refrigerator Defrost Thermostat is a genuine OEM part designed to regulate the defrost cycle by monitoring the temperature near the evaporator coils. When the temperature drops to a preset level, the thermostat activates the defrost heater to melt frost and maintain proper airflow. A faulty defrost thermostat can cause excessive frost buildup and cooling problems. This OEM replacement ensures reliable operation and is ideal for long-term use in compatible refrigerator models.
Replaces Part Numbers
This OEM thermostat replaces WR50X60, 3489, WR23X5030, WR50X0005, WR50X0007, WR50X0010, WR50X0011, WR50X0017, WR50X0021, WR50X0023, WR50X0026, WR50X0027, WR50X0036, WR50X0060, WR50X0076, WR50X0077, WR50X0089, WR50X0091, WR50X0093, WR50X0101, WR50X0105, WR50X0107, WR50X0110, WR50X0111, WR50X0115, WR50X0125, WR50X10, WR50X101, WR50X105, WR50X107, WR50X11, WR50X110, WR50X111, WR50X115, WR50X125, WR50X17, WR50X21, WR50X23, WR50X26, WR50X27, WR50X36, WR50X5, WR50X5009, WR50X5026, WR50X7, WR50X76, WR50X77, WR50X89, WR50X91, WR50X93, AH303547, EA303547, AP2071242, PS303547.
It offers a direct fit and performance consistent with original factory-installed components.
Compatible Brands
Compatible with GE, Hotpoint, and Kenmore refrigerators made by GE. It fits various top-freezer, bottom-freezer, and side-by-side models that use this thermostat in their defrost systems.
Fixes the Following Issues
Frost accumulation in freezer
Refrigerator not defrosting
Blocked airflow due to ice
Inconsistent cooling performance
Why Buy from Parts‑O‑Matic
100% genuine OEM part for guaranteed compatibility
Fast and free shipping throughout the U.S.
Trusted by appliance technicians and DIYers
Hassle-free returns and responsive support
5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot)
The 5220FR2006H is a genuine LG OEM hot water inlet valve for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's hot water line and controls the flow of hot water into the tub during the fill portion of each cycle, opening as the cycle calls for hot water and closing once the correct fill level and temperature mix are reached. The valve has a standard hose fitting inlet and a single water outlet.
Common causes of failure include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid. Symptoms of a failing valve include the washer not filling, not stopping when it should, not starting, leaking water, not washing properly, no hot water reaching the tub, or an IE error code displayed on the control panel. It directly replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427.
Quick Answer
The 5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot) fixes LG and select Kenmore front-load washers with no hot water, won't fill, won't stop filling, won't start, leaking, or an IE error code. Standard hose fitting inlet, 1 outlet. Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427. This is the hot water valve — a separate but related cold water valve is used alongside it. If both valves are original and the same age, consider replacing both together while you have the washer open.
Common Problems This Part Fixes
No hot water reaching the tub
Washer not filling with water
Washer not stopping fill when it should
Washer not starting
Water leaking from the valve area
IE error code displayed on the control panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers:
1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hot water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform, including model numbers such as WM2240CW, WM2250CW, WM2277HW, WM3170CW, WM3250HV, 40272, 40441 (ABWESEU), 41002, 41003, 41172 (ABWEPEU), 41172 (ABWESEU), 41182, 41262 (ABWEPEU), 41262 (ABWEVEU), and 41283.
Note: This is the hot water valve. Our 5220FR2008C listing is the related cold water valve, and our 5220FR2008F listing is a closely related water inlet and dispenser valve assembly used on other models — these are separate parts serving different roles or platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your washer needs.
Key Features
Genuine LG OEM part — factory-specified solenoid design and flow rate
Regulates hot water flow into the tub during fill
Resolves "no hot water," "won't fill," "won't stop filling," "won't start," "leaking," and "IE error code" symptoms
Standard hose fitting inlet, 1 water outlet
Direct drop-in replacement — matches the original mounting and hose connections
Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427
Compatible with LG and select Kenmore front-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Simple 15-minute DIY repair
Product Specifications
Part Number
5220FR2006H
Part Type
Washer Hot Water Inlet Valve
Condition
Genuine OEM
Brand
LG
Application
Front-Load Washers
Inlet
Standard hose fitting
Outlet
1
Related Part
5220FR2008C cold water valve (sold separately)
Repair Difficulty
Easy — approx. 15 minutes
Quantity
1 valve
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting Turn off the water supply and unplug the washing machine from the wall before beginning. Wear work gloves. Locate the top cover of your washer — depending on your model, it may be located along the side or in the back — and use a flat-blade screwdriver to gently pry it off. Locate the hot water valve and disconnect the water supply hose from it, using locking pliers to loosen the hose clamp before carefully pulling the hose away. Unscrew the screws holding the valve in place and gently remove it from the washer. Mount the new 5220FR2006H valve in place and replace the screws. Reconnect the water supply hose to the valve and tighten the hose clamp using locking pliers. Turn the water supply back on and plug the washer back in. Test the new valve by running a load of laundry and checking for any leaks. Tools needed: flat-blade screwdriver, locking pliers, work gloves.
Frequently Asked Questions
My washer isn't getting hot water. Is this the part I need?
Yes, this is the most direct symptom of a failed hot water inlet valve. Since this valve is what admits hot water from your household supply into the washer, a solenoid failure or internal blockage can prevent hot water from entering properly, even if cold water fill still works normally.
My washer shows an IE error code. Could this valve be the cause?
Yes, an IE error code on LG washers is commonly tied to a fill issue, and a failed inlet valve — hot or cold — is one of the most frequent causes. Confirm which side (hot or cold) is actually affected before ordering, since these are separate parts.
Should I replace the cold water valve at the same time?
It's worth considering, especially if both valves are the same age. One customer specifically purchased both the hot and cold water inlet valves together during a single repair, along with a new drain pump motor, rather than tackling each part separately over multiple repairs.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the hot water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W10838313 Genuine OEM Whirlpool Freezer Wire Shelf (Lower)
The W10838313 is a genuine Whirlpool OEM wire shelf that sits at the floor of the freezer section on Whirlpool upright freezers. This is the lowermost shelf in the compartment, sliding into grooves molded into the freezer's interior walls to provide a sturdy, ventilated surface for storing frozen goods. Unlike a solid shelf, the open wire construction lets cold air circulate freely around whatever is stored on it, which helps maintain even freezing throughout the compartment.
Measuring approximately 12" x 25" (11.65"W x 24.55"L), this shelf is made of coated wire with a white finish. Over years of loading and unloading groceries, the wire can weaken, bend, or separate from its retaining clips, and constant weight can eventually cause sagging or wobbling. A worn shelf typically shows up as wobbling under load, difficulty locking securely into its groove position, or wires that have visibly pulled loose from their retention brackets. It directly replaces AP5988764, W10581579, 4363361, PS11727969, and W10837264.
Quick Answer
The W10838313 Genuine OEM Whirlpool Freezer Wire Shelf (Lower) fixes Whirlpool upright freezers with a bottom shelf that wobbles, sags, won't lock securely into place, or has wires separating from the retaining clips. Approximately 12" x 25" (11.65"W x 24.55"L). Replaces AP5988764, W10581579, 4363361, PS11727969, W10837264. This is the lower shelf — the upper shelf for the same freezers is a separate, wider part, W10838310 (15.75"W). Double-check which shelf you need before ordering.
Common Problems This Part Fixes
Shelf wobbling or sagging under the weight of stored food
Inability to securely lock the shelf into its groove position
Wires separating or pulling loose from the retaining brackets
Visibly bent, weakened, or broken wire sections
Shelf that no longer sits level, causing items to slide or tip
Missing or broken original shelf needing straightforward replacement
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This freezer wire shelf directly replaces the following OEM and cross-reference part numbers:
W10838313, W10837264, W10581579, 4363361, AP5988764, AWP41859, EAP11727969, PD00031016, PS11727969
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lower wire shelf is compatible with select Whirlpool upright freezers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore upright freezers, including model numbers such as WZF34X16DW, WZF34X18DW, and GAFZ30FDGB.
Note — lower shelf, not upper: This is the lower wire shelf. The upper shelf used on the same freezers is a separate, wider part — W10838310 (15.75"W, replacing AP5988763, W10581578, 4363360, PS11727968, EAP11727968). Customers have ordered the wrong one by mistake since the two look similar at a glance — measure your existing shelf or confirm which position (upper or lower) has failed before ordering. Contact our support team with your model number if you're unsure which shelf you need.
Key Features
Genuine Whirlpool OEM part — factory-specified wire gauge and coating
Open wire construction allows cold air to circulate freely around stored items
Resolves "wobbling," "sagging," "won't lock in place," and "wires separating from clips" symptoms caused by shelf wear
Slides directly into existing grooves molded into the freezer's interior walls
Approximately 12" x 25" (11.65"W x 24.55"L)
No tools required — simple slide-out, slide-in replacement
Replaces W10837264, W10581579, 4363361, AP5988764, and PS11727969
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore upright freezers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W10838313
Part Type
Freezer Wire Shelf — Lower
Condition
Genuine OEM
Brand
Whirlpool
Application
Upright Freezers
Position
Lower (floor of freezer compartment)
Dimensions
Approx. 12"W x 25"L (11.65"W x 24.55"L)
Material
Coated wire
Color
White
Companion Part
W10838310 (upper shelf, 15.75"W, sold separately)
Repair Difficulty
Very Easy — no tools required
Quantity
1 wire shelf
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
This is one of the simplest repairs in the freezer — no tools, no wiring, nothing to disconnect. Open the freezer door and remove any food from the affected shelf position. Slide the old shelf forward and out along its grooves until it clears the cabinet. Line up the new W10838313 shelf with the same grooves at the bottom of the freezer compartment, and slide it in until it seats fully at the back. Close the door and confirm the shelf sits level and locks securely before reloading it with food.
Frequently Asked Questions
How do I know if I need the upper or lower shelf?
Check which position in your freezer has the wobbling, sagging, or damaged shelf — this W10838313 listing is specifically the lower shelf that sits at the floor of the freezer compartment. The upper shelf is a separate part, W10838310, and it's noticeably wider (15.75" versus this shelf's narrower width). If you're not certain, measure your existing shelf before ordering, since customers have accidentally ordered the wrong position in the past.
Do I need any tools to install this?
No. This is a tool-free repair — slide the old shelf out along its grooves, then slide the new one in until it seats. It's one of the easiest parts to replace in the entire freezer.
My shelf wobbles but isn't broken. Is it still worth replacing?
If the wobble is due to weakened or bent wires rather than just needing to be reseated in its grooves, replacement is the more reliable fix. Try removing the shelf and reseating it fully first — if it still wobbles or won't lock securely after that, the wire has likely weakened enough that a new shelf is the better long-term solution.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original dimensions, wire gauge, and coating of the lower freezer shelf originally installed in your Whirlpool, Maytag, KitchenAid, or related upright freezer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
