Search results for "Dryer belts and idler pulley"

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5303281153 Dryer Genuine OEM Rear Drum Bearing The 5303281153 is a genuine Frigidaire OEM rear drum bearing kit for Frigidaire dryers, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse models. This ball-and-socket style bearing supports the rear of the dryer drum, reducing friction and allowing the drum to rotate smoothly and quietly throughout the drying cycle. The bearing itself measures approximately 1-15/16"L x 1"W x 1-3/8"H, with mounting holes 1-1/2" apart, center to center. The holes in the metal mounting plate are not pre-threaded — the self-tapping screws included in the kit are what create the threads during installation. Common causes of failure include normal wear and tear, exposure to excessive heat or lint buildup, or physical damage from impact or overloading. Symptoms of a worn or failing rear drum bearing include excessive noise or grinding sounds, difficulty rotating the drum or a drum that won't turn at all, visible wear or damage on the bearing, or increased vibration and shaking during the drying cycle. It directly replaces AP2142648, 1851, 3281153, 5304459240, 85-852, AH459829, DE724, EA459829, PS459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 175428, 175432, 175433, 31581400, 3281019, 3281020, 5303281019, and 5303281020. Quick Answer The 5303281153 Dryer Genuine OEM Rear Drum Bearing fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse dryers with excessive noise or grinding, a drum that won't turn or turns with difficulty, or increased vibration. Ball-and-socket style, ~1-15/16"L x 1"W x 1-3/8"H. Replaces AP2142648, 1851, 3281153, 5304459240, 85-852, AH459829, DE724, EA459829, PS459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 175428, 175432, 175433, 31581400, 3281019, 3281020, 5303281019, 5303281020. The mounting plate holes aren't pre-threaded — the included self-tapping screws create the threads as you install them, so take your time getting them started straight. What's In The Kit Component Function Ball Shaft (131777700) The shaft the drum rotates on at the rear support point. Teflon Shaft Bearing (131825900) Reduces friction between the shaft and its bracket. Shaft Bearing Bracket (131724301) Mounts the bearing assembly to the rear bulkhead. Ball Bearing (5303281019) & Clip (5303281020) Supports the ball shaft and secures it in place. Mounting Screws & Washers Self-tapping screws (3 for the shaft, 2 for the bracket) that thread into the unthreaded metal plate. High-Temperature Lubricant Tube Lubricates the bearing assembly for quiet, smooth operation. Common Problems This Kit Fixes Excessive noise or grinding sounds from the rear of the dryer Drum won't turn, or turns with difficulty Visible wear or damage on the existing bearing Increased vibration or shaking during the drying cycle Loud squealing when the dryer runs Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer rear drum bearing kit directly replaces the following OEM and cross-reference part numbers: 5303281153, 1851, 3281153, 5304459240, 85-852, AH459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 3281019, 3281020, 5303281009, 5303286875, 8015113, 8015324, 902088, Q000022224, Q000500537, WQ22224, WQ500537, AFR17081, AP2142648, DE724, EA459829, EAP459829, PD00000097, PS459829 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This rear drum bearing kit is compatible with select Frigidaire dryers, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse dryers built on the Frigidaire platform. Note: This kit is commonly purchased alongside a drum belt (such as our 137292700 listing), since both are accessed through the same disassembly and often wear on a similar timeline. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — complete rear drum bearing kit in one purchase Resolves "excessive noise," "won't turn," "worn bearing," and "vibration" symptoms Ball-and-socket style bearing design Includes ball shaft, Teflon shaft bearing, bearing bracket, ball bearing and clip, mounting screws and washers, and a high-temperature lubricant tube Approximately 1-15/16"L x 1"W x 1-3/8"H, mounting holes 1-1/2" apart Replaces AP2142648, 1851, 3281153, 5304459240, 85-852, AH459829, DE724, EA459829, PS459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 175428, 175432, 175433, 31581400, 3281019, 3281020, 5303281019, and 5303281020 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5303281153 Part Type Dryer Rear Drum Bearing Kit Condition Genuine OEM Brand Frigidaire Bearing Style Ball-and-socket Bearing Dimensions Approx. 1-15/16"L x 1"W x 1-3/8"H Mounting Hole Spacing 1-1/2" apart, center to center Mounting Plate Not pre-threaded — self-tapping screws included Includes Ball shaft, Teflon bearing, bracket, ball bearing + clip, screws, washers, high-temp lubricant Repair Difficulty Moderate Quantity 1 rear drum bearing kit Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dryer Before Starting — Mounting Plate Holes Are Not Pre-Threaded Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel and the drum belt to access the drum, then remove the drum itself to reach the rear bearing assembly. While the dryer is open, take the time to clean out any accumulated lint from inside the cabinet and around the motor, since buildup here is common and worth clearing while you have access. Remove the old bearing bracket, ball shaft, and related hardware. Apply the included high-temperature lubricant to the new Teflon shaft bearing and ball bearing as directed. Assemble the new ball shaft, bearing, and bracket, then mount the bracket to the rear bulkhead. The holes in the metal mounting plate are not pre-threaded — use the self-tapping screws included in the kit to thread the plate as you install them. If the included screws feel blunt or don't bite well, threading with your original screws first and then switching to the new screws for final installation can help. Reinstall the drum, making sure it seats correctly on the new bearing. Reattach the drum belt and back panel, and double check that no leftover screws remain before closing everything up. Restore power and run a test cycle to confirm quiet, smooth drum rotation. Tools needed: nut driver, Phillips or square-drive screwdriver, work gloves. Frequently Asked Questions My dryer is making a loud grinding or squealing noise. Is this the part I need? Yes, this is one of the most common symptoms of a worn rear drum bearing. One customer described their dryer as no longer "talking back" after the repair — no more chatter or grinding — confirming this bearing was the source of the noise. Why does it matter that the mounting plate holes aren't pre-threaded? Since the plate isn't pre-threaded, the self-tapping screws included in the kit have to cut their own threads as you install them, which takes a bit more care than screwing into an already-threaded hole. One customer found the included screws were blunt and didn't tap easily, and got better results starting the threads with their original, sharper screws before switching to the new screws for the final installation. Should I clean anything else while I have the dryer open for this repair? Yes, it's worth it. One customer found their motor "completely embedded with lint and animal hair" during this repair and spent extra time cleaning it out. Since you'll already have the back panel and drum removed, this is a good opportunity to clear out accumulated lint throughout the cabinet. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original bearing style, dimensions, and hardware configuration of the rear drum bearing kit originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

131775600 Dryer Genuine Blower Wheel and Housing Complete housing and captive blower assembly. Fits specific Frigidaire, Electrolux dryer models. Replaces Part Numbers: 131775600, 131775610, AH418726, EA418726, OEM6322823, AP2107606, PS418726. Description: This Blower Housing Assembly is a Genuine part for specific Frigidaire dryer models. It houses the blower wheel, which circulates air through the dryer drum and out the exhaust. This assembly ensures that hot air is efficiently directed through the dryer to dry clothes properly.  Common Cause is the blower housing assembly can become damaged or worn out, affecting the dryer's performance. Causes of a bad blower housing assembly can include accumulation of lint or debris, wear and tear from frequent use, or physical damage to the housing or blower wheel.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM WP3406107 Dryer Door Switch The Genuine OEM Whirlpool WP3406107 is a dryer door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. It mounts inside the top of the dryer's front panel, with one end connecting to the wiring harness and the other passing through the panel to make contact with the door. When the door closes, it presses the switch's black tab, which tells the dryer the door is shut so it can run. When the switch wears out, the dryer may not start, may run with the door open, or may lose its interior light. This is the original Whirlpool part, a white, 6.5 inch, three-wire switch. Retailers describe the switch as a regular wear part and rate the repair as really easy, typically 15 to 30 minutes. Quick Answer The Genuine OEM WP3406107 Door Switch fixes a Whirlpool, Kenmore, Maytag, or KitchenAid dryer that won't start, runs with the door open, has a light that doesn't work, or has a door that won't close properly. Quick test: with the dryer unplugged, press the switch's black tab. If it has no resistance and doesn't click, the switch likely needs replacing. Common Problems This Part Fixes Dryer won't start Dryer runs with the door open Interior light doesn't work Door won't close or latch properly against the switch Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, W10569603, 3405100, 3405101, 3406100, 3406101, 528948, 11259-65, 11288-80, WP3406107VP, AP6008561, AWP47183, EAP11741701, PD00002378, PS11741701 These numbers come from retailer cross-reference lists and span several generations of Whirlpool's own numbering for this switch. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This door switch is listed for Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including these examples: Kenmore 11060372710, 11060522900, 11060702990, 11060802990 Kenmore 11061202010, 11061262311, 11061802000 Whirlpool EED4400WQ Note: The models above are a small sample of a longer list, not a full list. This is a three-wire switch that replaces the two-wire switch found on many models, so compare it to your old switch, and contact our support team with your model number to verify fit before ordering. Key Features Genuine OEM Whirlpool dryer door switch, not an aftermarket equivalent Three-wire design; replaces the two-wire switch on many models White, 6.5 inch switch with a spring-loaded black tab Resolves no-start, runs-with-door-open, and light problems caused by a worn switch Typically a 15 to 30 minute repair Product Specifications Part Number WP3406107 OEM Part Number WP3406107 Part Type Dryer Door Switch Condition Genuine OEM Manufacturer Whirlpool Length 6.5 Inches Color White Wire Configuration Three-Wire Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as cabinet edges can be sharp. The switch is mounted inside the top of the front panel, so follow your model's service guide to remove the panel needed to reach it. Note how the wiring connector is attached, disconnect it, and remove the old switch. Fit the new switch in the same position, reconnect the wiring, and reassemble. Restore power and confirm the dryer starts with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start. Is this the part I need? A worn door switch is a common cause. With the dryer unplugged, press the switch's black tab. If there is no resistance and no click, the switch likely needs replacing. My dryer runs with the door open. Is that a problem? Yes. The door switch is a safety part that stops the dryer from running when the door is open. If the dryer runs with the door open, replace the switch promptly. My dryer has a two-wire switch. Will this three-wire switch work? Retailers list this three-wire switch as the replacement for the two-wire switch found on many models. Compare it to your old switch and your wiring, or contact our support team with your model number, before ordering. Will this fit my dryer? It is listed for many Whirlpool, Kenmore, Maytag, and KitchenAid dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ADQ56656401 Genuine OEM LG Dryer Lint Screen The ADQ56656401 is a genuine LG OEM lint filter screen for LG and select Kenmore Elite front-load dryers. This is the removable screen that sits in the lint trap opening at the top of the dryer, catching lint and fabric fibers out of the exhaust airflow before they can reach the vent duct. Keeping this screen intact and free of buildup is one of the most important things you can do for your dryer's performance — a torn, missing, or heavily clogged screen doesn't just slow drying, it lets more lint travel downstream into the ducting, which is a well-documented fire risk factor for dryers generally. Built with an ABS plastic frame and a stainless steel mesh screen, this filter measures approximately 11.9" x 10.9". Over time the mesh can tear, the frame can crack, or the screen can simply wear out and stop trapping lint as effectively as it should. A worn or damaged lint screen typically shows up as drying times that have crept longer than they used to, visible lint on clean clothes, or a screen that's visibly torn, bent, or missing sections of mesh. It directly replaces AP4457244, 1462822, AH3531962, EA3531962, and PS3531962. Quick Answer The ADQ56656401 Genuine OEM LG Dryer Lint Screen fixes LG and select Kenmore Elite front-load dryers with a torn, cracked, missing, or heavily worn lint filter, showing up as longer drying times or lint on clean clothes. ABS frame with stainless steel mesh, approximately 11.9" x 10.9". Replaces AP4457244, 1462822, AH3531962, EA3531962, PS3531962. Not the same filter as ADQ56656403, which is a slightly smaller (11.2" x 10.9") screen used on LG WashTower models. Common Problems This Part Fixes Drying times that have gradually gotten longer than they used to Lint visible on clean clothes after a cycle Lint screen visibly torn, cracked, or missing sections of mesh Screen frame that's cracked, warped, or won't seat properly in the trap opening Reduced airflow through the dryer overall Lint screen that has gone missing and needs straightforward replacement Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer lint screen directly replaces the following OEM and cross-reference part numbers: ADQ56656401, AP4457244, EAP3531962, PS3531962, ALG52875, PD00001720, AH3531962, EA3531962 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lint screen is compatible with select LG front-load dryers, and also fits select Kenmore Elite dryers built on the LG platform, including model numbers such as: DLE3170W, DLE3400W, DLE3500W, DLE3600V, DLE3050W DLEX3360V, DLEX3370V, DLEX3370W, DLEX3370R, DLEX3470V, DLEX3470W, DLEX3570V, DLEX3570W, DLEX3700V, DLEX3700W, DLEX3900W, DLEX4370K, DLEX3001R DLG3171W, DLG3401W, DLGX3361R, DLGX3361V, DLGX3361W, DLGX3371V, DLGX3371W, DLGX3471W, DLGX4271W, DLGX3002R DLE2601R, DLE2601W, DLE2701V, DLEX2801L, DLEX2801R, DLEX2801W, DLEX2901V, DLEX3001W, DLEX3001P, DLEX3875V, DLEX3875W DLG2602R, DLG2602W, DLG2702V, DLGX2802L, DLGX2902V, DLGX3002P, DLGX3002W, DLGX3876V Kenmore Elite RN1308AS, RN1308BS, RN1308CS, RN1310A, RN1310AS, RN1310B, RN1310BS, RN1310DS, RN1319E, RN1319VS, RN1321VS, RV1308AS, RV1308BS, RV1308CS, RV1310A, RV1310AS, RV1310B, RV1310BS, RV1310DS, RV1319E, RV1319VS, RV1321AS, RV1321VS Note — not the same as ADQ56656403: This lint screen is approximately 11.9" x 10.9". A similarly-numbered part, ADQ56656403, is a slightly smaller 11.2" x 10.9" screen used on LG WashTower models such as DLEX4000W, DLGX4001W, DLGX4201B, and DLGX4201W. The two are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lint screen fits your dryer. Key Features Genuine LG OEM part — factory-specified frame dimensions and mesh density ABS plastic frame with a stainless steel mesh screen for durability Resolves "longer drying times," "lint on clean clothes," and "torn or missing screen" symptoms Traps lint and fabric fibers before they reach the exhaust ducting Approximately 11.9" x 10.9" Direct drop-in replacement — lifts out and in with no tools required Replaces AP4457244, 1462822, AH3531962, EA3531962, and PS3531962 Compatible with LG and select Kenmore Elite front-load dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number ADQ56656401 Part Type Dryer Lint Screen / Filter Condition Genuine OEM Brand LG Frame Material ABS plastic Screen Material Stainless steel mesh Dimensions Approx. 11.9" x 10.9" Location Lint trap opening, top of dryer Repair Difficulty Very Easy — no tools required Quantity 1 lint screen Compatible Brands LG, Kenmore Elite Installation Notes This is a simple, tool-free repair. With the dryer unplugged or off, locate the lint trap opening at the top of the dryer and pull the old lint screen straight up and out. Line up the new ADQ56656401 screen with the same opening and slide it back down into place until it seats fully and sits flush. There's no need to disconnect power for this repair, but it's good practice to do so if you're also cleaning out the trap housing itself. While the screen is out, take a moment to wipe down the inside of the lint trap housing to clear any accumulated lint before reinserting the new screen. Tools needed: none. Frequently Asked Questions My drying times have gotten longer. Is a worn lint screen really the cause? It's one of the most common and easiest-to-fix causes. A torn or heavily worn screen lets lint pass through into the ducting instead of being caught, which restricts airflow further downstream and makes the dryer work harder to move air. Combined with regularly cleaning the screen after every load, a fresh screen in good condition helps restore normal drying times. Is it actually important to replace a torn lint screen, or is it just cosmetic? It's worth replacing rather than continuing to use a damaged screen. A torn or heavily worn lint filter lets more lint travel past it into the dryer's internal ducting and exhaust path, and lint buildup in that ducting is a well-documented dryer fire risk factor. Combined with never running the dryer without a lint filter in place at all, keeping the screen in good condition is a simple, inexpensive way to reduce that risk. Do I need any tools to replace this? No. The lint screen simply lifts straight out of its slot and the new one slides straight back in — no tools, no disassembly required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original frame dimensions, mesh material, and fit of the lint screen originally installed in your LG or Kenmore Elite dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM 280187 Washer Drain Pump Assembly The 280187 is a genuine OEM drain pump assembly from Whirlpool for Whirlpool-built front-load washers sold under the Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid, and Amana names. The drain pump pushes water out of the tub through the drain hose at the end of the wash and rinse stages. When it clogs, wears out, or seizes, the washer can stop with water still in the drum, throw drain errors, stop before the spin cycle, leak, or make loud humming or grinding noises. This is a complete drain pump assembly, including the pump motor and housing, so it replaces the whole unit rather than just an internal part. As a genuine OEM part, not an aftermarket equivalent, it matches the original factory fit and specification. The pump sits at the base of the washer behind the lower front panel, and the swap typically takes 15–30 minutes with common hand tools. Quick Answer The Genuine OEM 280187 Drain Pump Assembly fixes a Whirlpool-built front-load washer that won't drain, leaves water in the drum, stops before spinning, leaks from the pump, or makes loud noise during draining. Complete pump motor and housing, genuine OEM. Classic symptom: the cycle stalls with water still in the tub, or you hear a loud hum or grind while it tries to drain. Common Problems This Part Fixes Washer won't drain, or water is left in the drum after the cycle Drain error codes or the cycle stopping before the spin Loud humming, grinding, or rattling while the washer drains Water leaking from the pump or its housing Pump motor seized or not running Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump assembly replaces the following part numbers: 280187 replaces 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610 These are Whirlpool's current and earlier numbers for this pump. If your old pump or parts diagram shows any of them, this is the matching replacement. Compatibility This pump is listed for select front-load washers from: Whirlpool, including Duet models such as WFW9400VE03, WFW9500TW03, and WFW9600TW02 Kenmore and Kenmore Elite, including 11042822200, 11042926200, 11045962400, and 11045966403 Maytag, including MHWE400WR00 and MHWE400WW0 KitchenAid, including KHWS02RWH0 Amana Note: The model list above is only a sample, since this pump fits many more models. Confirm fit by matching the number on your old pump or parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This pump is for front-load washers and is not intended for top-load machines. Key Features Genuine OEM Whirlpool drain pump assembly, not an aftermarket equivalent Complete unit with pump motor and housing Restores full draining so cycles finish and the washer can spin Cross-references to Whirlpool 280187, 285998, 8181684, 8182819, and 8182821 Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and Amana front-load washers Typical installation 15–30 minutes with common hand tools Product Specifications Part Number 280187 OEM Part Number 280187 Part Type Washer Drain Pump Assembly Condition Genuine OEM Included Pump Motor and Housing Application Select Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid & Amana Front-Load Washers Installation Notes ⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Remove the lower front panel to reach the pump at the base of the washer, then drain any residual water into a shallow pan or with a wet/dry vacuum, using the drain hose or the small drain cap if your model has one. Disconnect the wiring harness from the pump, then loosen the clamps holding the hoses and pull the hoses off. Remove the pump's mounting screw and take out the old pump. Fit the new pump in the same position, reattach the hoses with the clamps (replace worn clamps if needed), and reconnect the wiring harness. Check that the pump and hose connections are secure, replace the front panel, restore power and water, and run a drain cycle while checking for leaks. Common tools include a nutdriver or Torx driver, screwdrivers, and pliers. Frequently Asked Questions My washer won't drain. Is this the part I need? A failed or clogged drain pump is one of the most common causes. Before replacing it, check the drain hose and the pump filter for a clog, such as a sock or coin. If the filter is clear but the pump hums, grinds, or doesn't run, replacing the pump should fix it. Does this include the pump motor? Yes. This is the complete assembly, with the pump motor and housing. My old pump is marked 285998, 8181684, 8182819, or 8182821. Will this work? Yes. All of those are earlier Whirlpool numbers for this pump, and 280187 is the current number. Will this fit my top-load washer? It is intended for front-load washers. Contact our support team with your model number if you're unsure, and we'll confirm before you order. Is this an OEM part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent, so it matches the original factory fit and specification. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 3129480 Dryer Drum Support Roller Shaft Fits Specific Maytag, Amana, Admiral Dryer Models. Replaces Part Number: WP6-3129480, 6-3129480, 1480353, 3-12948, 312948, W10912638, WP6-3129480VP, Y312948, AP6009858, PS11743031. Description: The Dryer Drum Roller Axle is a replacement part for specific Maytag, Admiral, Whirlpool dryer models. It plays a role in the dryer's operation by offering support and an axis for the drum roller to spin smoothly. This guarantees effective and balanced tumbling of clothes throughout the drying cycle.  This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line. Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535. Quick Answer The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause. Common Problems This Part Fixes Dishwasher won't drain at the end of the cycle Water pooling at the bottom of the tub after a completed cycle Grinding or humming noise coming from the pump area Dishwasher won't start a new cycle because it detects leftover water from the previous one Dishes not getting properly cleaned due to poor water circulation Pump running but producing little or no actual drainage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform. Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified motor speed and impeller design Pumps water out of the tub and through the drain hose at the end of each cycle Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure Includes pump motor, impeller, and seal Rated 120V, 60Hz, 35W, 0.8A, 3600RPM 1/4" male terminals for a direct plug-in electrical fit Direct drop-in replacement — no modification required Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number A00126401 Part Type Dishwasher Drain Pump Motor Assembly Condition Genuine OEM Brand Frigidaire Voltage 120V Frequency 60 Hz Wattage 35 W Amperage 0.8 A Motor Speed 3600 RPM Terminals 1/4" male Kit Contents Pump motor, impeller, seal Dimensions Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H Color White / Green Repair Difficulty Easy to Moderate — under an hour Quantity 1 drain pump motor assembly Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore Installation Notes ⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves. Frequently Asked Questions My dishwasher won't drain. How do I know if it's actually the pump and not something simpler? Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix. I already replaced the pump and it's still not draining. What should I check next? This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing. Does this kit include the check valve flapper? This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00016A Dishwasher Drain Pump Motor The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs. Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701. Quick Answer The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers. Common Problems This Part Fixes Dishwasher not draining water from the tub Standing water left in the tub after a completed cycle Unusual noise during the drain phase Intermittent draining problems that don't occur every cycle Reduced water circulation and cleaning performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG. Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement BLDC (brushless DC) drain pump motor Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms Impeller mechanism pumps water out through the drain hose to prevent clogs Compatible with 120V and 230V systems Direct drop-in replacement matching the original mounting and connections Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701 Compatible with Samsung dishwashers Aftermarket replacement built to OEM-equivalent quality standards Typical repair takes 30 to 60 minutes Product Specifications Part Number XPDD31-00016A OEM Part Number DD31-00016A Part Type Dishwasher Drain Pump Motor (BLDC) Condition Aftermarket Replacement Brand Samsung Motor Type Brushless DC (BLDC) Voltage Compatibility 120V / 230V Weight Approx. 0.50 lbs Package Dimensions 4.02" x 3.50" x 3.54" Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves. Frequently Asked Questions My dishwasher isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly. My dishwasher's drainage problem only happens sometimes. Could this still be the motor? Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue. What's the trickiest part of installing this motor? Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279393 Dryer Terminal Block Screw Kit The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing. This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools. Quick Answer The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more. Common Problems This Part Fixes Dryer has intermittent power or will not start at all Internal fuses repeatedly blowing without another clear cause Circuit breaker for the dryer repeatedly tripping Terminal block area is hot to the touch during or after operation Visible arcing, sparks, scorch marks, or smoke around the terminal block cover Heating element or motor works intermittently but not consistently Dryer power cord connection is loose, corroded, or visibly damaged Replaces Part Numbers This terminal block screw kit directly replaces the following OEM and cross-reference part numbers: 279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This terminal block screw kit is compatible with select electric dryers from the following brands: Whirlpool electric dryers Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Roper electric dryers Admiral electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Magic Chef, Norge, and Jenn-Air electric dryers Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections. Key Features Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions Chrome-plated metal construction — improves electrical conductivity and resists corrosion Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with basic hand tools Product Specifications Part Number 279393 Part Type Terminal Block Screw and Nut Kit Condition Aftermarket Replacement Application Electric Dryers (240V terminal block) Kit Contents 3 chrome-plated screws and 3 nuts Screw Dimensions 7/16" L x 7/16" W x 11/16" H Nut Dimensions 1/2" L x 1/2" W x 1/8" H Material Chrome-plated metal Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air Dryer Type Electric dryers only ⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician. Installation Notes ⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the terminal block screw kit used for? The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss. Can I also use this kit when installing a new dryer power cord? Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start. Should I also inspect the terminal block itself? Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model. Does this kit work for gas dryers? No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WPW10409079 Washer Genuine OEM Drain Pump Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079. Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.  The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.

Read more less

🚪 XPARTCO 131658800 Dryer Door Catch This Door Catch is a replacement part for specific Kenmore, Frigidaire dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number 131658800. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit many Frigidaire, Kenmore, Electrolux, and Crosley dryers. ✅ Key Features: High-quality aftermarket replacement for part #131658800 Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: 131658800, 131658820, 131658845, 00634863, 07521419, 08015370, 134548000, 134548045, 3004967, 3202755, 3281055, 5303281055, 5307521419, 7521419, 835, AH418433, EA418433, F141735-000, F141735000, F62661-4, K1300884, K1301594, K1308079, K1309301, N8010215, Q0000401002, Q000504551, Q000504553, Q504551, Q504553, WQ504551, WQ504553, AP2107362, PS418433, WE01X25316, AP6037347, 4512762, PS11766999. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Gibson✔️ Tappan✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the 131658800 dryer door catch from Parts-O-Matic.com, and enjoy fast, free U.S. shipping!

Read more less