Search results for "Washer Lid Switch"

AHA75673401 Washer Genuine Drain Pump Fits Specific LG Washer models Description:  This Washing Machine Drain Pump is an OEM part for specific LG washing machine models. It is responsible for effectively draining water out of the washing machine after each cycle. The pump works to remove water from the tub and drain hoses, preparing the machine for the next load.   Replaces Part Numbers:  AHA75673401, 4873470, AP6335290, PS12580277.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO AJU75152601 Washer Water Inlet Valve Replaces 5221EA1008F, AJU73213301 The XPARTCO AJU75152601 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the WT1, WT4, WT5, WT6, and WT7 series. This is a multi-port valve assembly that controls water flow from the household supply lines into the washer tub and dispenser compartments. The assembly contains multiple solenoid-operated valve ports: hot water inlet, cold water inlet, bleach dispenser valve, fabric softener dispenser valve, and jet spray valve — all integrated into a single assembly that connects to the washer's control board via wiring harnesses. When the water inlet valve fails — or when one individual port fails — the washer may not fill at all, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or leak from the valve body. The valve solenoids operate at 12V DC. This kit includes the complete valve assembly and two AGM73269501 inlet screens. It directly replaces AJU73213301, 5221EA1008F, 5221EA1008P, AGF76283896, AP6308239, TAW35618287, AH3527446, AJU75152603, EA3527446, PS3527446, and PS12374721. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO AJU75152601 Washer Water Inlet Valve fixes LG and Kenmore top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or leak from the valve. Multi-port assembly with hot, cold, bleach, fabric softener, and jet spray valves. 12V DC solenoids. Includes 2 AGM73269501 inlet screens. Compatible with LG WT1xxx–WT7xxx and Kenmore 796-series. Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, PS12374721. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more valve ports partially blocked or failing Washer filling with only hot or only cold water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach dispenser not dispensing during the wash cycle Fabric softener not dispensing at the correct rinse cycle point Jet spray not activating during fill Water dripping into the tub between cycles — valve port not closing completely Water leaking from the valve body or connection points at the back of the washer Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221EA1008F, AJU73213301, AJU75152601, AH3527446, AJU75152603, EA3527446, PS3527446, ALG53778, AP6308239, PD00042814, PS12374721, TAW35618287. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG and Kenmore top-load washers from the following series: LG top-load washers — WT1 series (WT1101CW, WT1201CW, WT1201CV, WT1301CW, WT1501CW, WT1701CW, WT1701CV, WT1801HVA, WT1801HWA and related models) LG top-load washers — WT4 series (WT4801CW, WT4870CW, WT4970CW and related models) LG top-load washers — WT5 series (WT5001CW, WT5070CW, WT5101HV, WT5101HW, WT5170HV, WT5270CW, WT5480CW, WT5680HVA, WT5680HWA and related models) LG top-load washers — WT6 series (select models) LG top-load washers — WT7 series (WT7200CW, WT7200CV, WT7500CW, WT7600HKA and related models) Kenmore / Sears top-load washers — 796-series (79631512210, 79631512211, 79631522211, 79631502210, 79631502211 and related models) Note: Always verify your exact model number before ordering. Newer LG WT7100/WT7150/WT7400/WT7405 series models use the AJU75152602 valve instead. Contact our support team with your model number to confirm the correct valve for your washer. Key Features Multi-port valve assembly — controls hot water, cold water, bleach dispenser, fabric softener dispenser, and jet spray from a single replaceable assembly 12V DC solenoid operation — responds to signals from the washer's control board to deliver the correct water to each compartment Resolves fill, dispenser, overfill, and drip-when-off symptoms in a single replacement Kit includes complete valve assembly and 2x AGM73269501 replacement inlet screens ABS plastic and stainless steel construction — durable and resistant to mineral buildup Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, and over 10 additional cross-reference numbers Compatible with LG WT1xxx through WT7xxx and Kenmore 796-series top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152601 Also Replaces AJU73213301, 5221EA1008F (current supersession) Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG and Kenmore Top-Load Washers Valve Ports Hot water, cold water, bleach dispenser, fabric softener dispenser, jet spray Solenoid Voltage 12V DC Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2x AGM73269501 inlet screens Compatible Series LG WT1xxx, WT4xxx, WT5xxx, WT6xxx, WT7xxx; Kenmore 796-series Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve assembly is mounted on the upper rear of the washer — the external supply hoses connect to the hot and cold inlet ports. Photograph all wire harness connections and hose routing before disconnecting anything. Before installing, install the new inlet screens (AGM73269501) included in the kit into the hot and cold inlet ports of the new valve. Disconnect the old valve's external supply hoses, internal hoses, and wire harness connectors. Unscrew the mounting screws and remove the old valve. Install the new AJU75152601 valve, reconnect all hoses and wire harnesses in the same positions as documented in your photos, and secure the mounting screws. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify proper filling, confirm all dispenser ports activate at the correct cycle points, and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152601, AJU73213301, and 5221EA1008F? These are all part numbers for the same LG washer water inlet valve assembly used across different production runs. 5221EA1008F was the original part number, AJU73213301 was an updated version, and AJU75152601 is the current part number. All three are interchangeable. If your washer's documentation, parts diagram, or old valve label shows any of these numbers, this replacement is the correct current part to order. My washer won't dispense fabric softener — is this the right part? Yes — the fabric softener dispenser solenoid is one of the ports integrated into the AJU75152601 valve assembly. When the fabric softener dispenser fails to activate at the right point in the rinse cycle, it is almost always because the solenoid valve controlling that port has failed. Since it is part of the same multi-port valve assembly, replacing the AJU75152601 resolves fabric softener, bleach, and jet spray dispenser issues in the same repair. Individual ports cannot be replaced — the complete assembly must be replaced when any one port fails. What are the AGM73269501 inlet screens included in the kit? The AGM73269501 screens are small mesh filters that install inside the hot and cold water inlet ports of the valve. They trap mineral deposits and debris from the household water supply before they can reach the valve seats and solenoid mechanisms. The kit includes two screens — one for the hot inlet and one for the cold inlet. Installing these fresh screens with the new valve helps extend valve life, especially in areas with hard water. If the old valve failed due to mineral clogging rather than solenoid failure, cleaning the supply hoses before installation is also recommended. How do I know if the water inlet valve has failed vs. the control board? You can test the valve solenoids with a multimeter. Disconnect the harness from a solenoid coil and probe both terminals — a working solenoid coil shows a resistance reading (typically 200–500 ohms); an open circuit confirms the solenoid has failed. If all solenoid coils test good but the valve still does not operate, the control board may not be sending the correct 12V DC signal to the solenoids — this requires checking voltage at the solenoid connectors with the washer powered and in a fill cycle, which is a more advanced diagnostic step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration, solenoid specifications, and dimensions of the original AJU75152601 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4 Pack - XPARTCO EXP480 Microwave Door Switch (NC - NO) Normally Closed / Open The XPARTCO EXP480 is a universal replacement door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch combines both a normally closed (NC) and normally open (NO) contact set in a single body, matching the dual-contact design used across a wide range of microwave door latch mechanisms. Rated 16A maximum current, 250VAC maximum voltage, with an IP40 protection rating. Over time, these switch contacts can wear, pit, or fuse together from repeated cycling and the electrical load they carry every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or in less common but more serious cases, a switch that has fused shut and continues carrying current even when it shouldn't. It directly replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, and PS10057151. Quick Answer The XPARTCO EXP480 Microwave Door Switch (NC - NO) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or have a door latch mechanism that isn't reliably cutting power when the door opens. 16A, 250VAC, combined NC/NO contact design. Replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, PS10057151. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated. Common Problems This Part Fixes Microwave won't start at all, even though the display and buttons respond normally Microwave display and timer work, but the unit won't heat Microwave stops working intermittently, especially around the door latch Clicking or buzzing sound from the door area without the microwave starting Breaker tripping when the door is opened, indicating a switch contact that has fused shut Door that doesn't feel like it's latching securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, W10727360, W10269457, 3379124, AP5950105, PS10057151 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands, wherever the original switch matches this NC/NO contact configuration and electrical rating. Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same NC/NO configuration. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs. Key Features Universal replacement microwave door interlock switch — combined NC (normally closed) and NO (normally open) contact design Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure Rated 16A, 250VAC maximum IP40 protection rating Safety approved: CCC, CE, UL, VDE Suitable for convection, grill, combination, and solo microwave ovens Direct drop-in replacement matching the original mounting and terminal configuration Replaces a wide range of OEM part numbers across Whirlpool, GE, and related platforms — see full list above Built to OEM-equivalent quality standards Product Specifications Part Number EXP480 Part Type Microwave Door Interlock Switch (NC/NO Combination) Condition New — Universal Replacement Part Contact Configuration Normally Closed (NC) + Normally Open (NO) Max. Current 16A Max. Voltage 250VAC Operating Temperature -25°C to +85°C Protection Degree IP40 Contact Form SPDT Terminal Size 6.3mm (approx. 1/4") Operating Force 25g (0.245N) – 400g (3.92N) Material Plastic Color Gray Safety Approvals CCC, CE, UL, VDE Application Convection, Grill, Combination, and Solo Microwave Ovens Installation Notes ⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead. ⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new EXP480 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My microwave stopped working. How do I know if it's actually a door switch and not something else? A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom. Is it safe to just disconnect a faulty interlock switch so the microwave will run? No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it. My microwave trips the breaker whenever I open the door. What does that mean? This can indicate that one of the door switches — often the one that should open when the door opens — has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave. My microwave uses more than one door switch. How do I know which one to replace? Most microwaves use two or three separate interlock switches working together, and they don't always share the same contact configuration. Check your appliance's parts diagram or the physical switch you're replacing to confirm it matches this NC/NO combination design before ordering, and always test or verify function with a multimeter if you're uncertain which specific switch has failed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

AAS73229402 Genuine OEM LG Washer Tub to Pump Hose The AAS73229402 is a Genuine OEM LG replacement tub-to-pump hose (also called a drain pump bellows assembly) compatible with a wide range of LG and Kenmore washing machines. This hose carries water from the outer tub to the drain pump, allowing the used wash and rinse water to properly empty from the tub during the drain cycle. It features flexible bellows that let the hose expand and contract as the tub moves during operation, while forming a watertight connection between the tub and the pump. When this hose cracks, splits, or develops porous areas, water leaks out during draining — typically showing up as a puddle under the washer. Made of durable rubber engineered to resist wear through years of flexing and water exposure. As a Genuine OEM part manufactured by LG to factory specifications, the AAS73229402 directly replaces AP6973533, AGM76891101, AHA75673401, and AEM74073303. This is one of those repairs where using the exact OEM hose matters — the correct fit and internal diameter ensure proper drainage and a leak-free seal, which unverified substitute hoses can't always guarantee. Installs in 30–60 minutes with basic hand tools. Quick Answer The AAS73229402 Genuine OEM LG Washer Tub to Pump Hose fixes LG and Kenmore washers that leak water under the machine during or after draining, don't fully drain the tub, leave standing water, or develop mold in the pump housing. Tub-to-pump hose / drain pump bellows assembly with flexible bellows — carries water from the outer tub to the drain pump. Genuine OEM. Replaces AP6973533, AGM76891101, AHA75673401, AEM74073303. Compatible with LG front-load and top-load washers plus select Kenmore models. Use the exact OEM hose for correct fit and diameter. Common Problems This Part Fixes Water leaking or puddling under the washer during or after the drain cycle Washer not fully draining — water left in the tub after the cycle Excess water left in the tub requiring additional emptying Drips or leaks from the tub-to-pump connection Standing water or mold growth inside the pump housing Hose visibly cracked, split, or showing porous/worn areas Hose no longer staying securely attached to the tub or pump Musty/moldy smell from water trapped by a leaking or sagging hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This tub-to-pump hose directly replaces the following OEM and cross-reference part numbers: AAS73229402, AAS73229405, AAS73229403, AGM76891101, AP6973533, PS12738715, ALG52189, PD00071151. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. For a proper leak-free seal, use the exact OEM hose rather than an unverified substitute — the correct fit and internal diameter matter. Compatibility This tub-to-pump hose is compatible with select LG and Kenmore washing machines, including front-load and top-load models: LG front-load washers — select WM-series models LG top-load washers — select WT-series models (including WT7305CV and related) LG washers using the AAS73229402 tub-to-pump bellows hose (verify with your parts diagram) Kenmore / Sears washers — select LG-built models Because LG uses several different tub-to-pump and drain hoses across its washer lineup, always verify your appliance model number before ordering to confirm the AAS73229402 is the correct hose for your machine. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by LG to factory specifications — guaranteed fit and performance Tub-to-pump hose (drain pump bellows assembly) — carries water from the outer tub to the drain pump for proper draining Flexible bellows design — expands and contracts as the tub moves during operation while keeping a watertight seal Resolves "leaking under the washer," "won't fully drain," "standing water," and "mold in pump housing" symptoms when caused by a failed hose Durable rubber construction engineered to resist cracking, splitting, and porosity over years of use Correct OEM fit and internal diameter for proper drainage and a leak-free seal Replaces AP6973533, AGM76891101, AHA75673401, and AEM74073303 Compatible with LG front-load (WM-series) and top-load (WT-series) washers, plus select Kenmore LG-built models Genuine OEM — the exact part sourced from the manufacturer DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number AAS73229402 Part Type Washer Tub-to-Pump Hose (Drain Pump Bellows Assembly) Condition Genuine OEM Application Front-Load & Top-Load Washing Machines (LG platform) Function Carries water from the outer tub to the drain pump Design Flexible bellows (expands/contracts with tub movement) Material Rubber Location Between the outer tub and the drain pump Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Drain the Tub First Unplug the washer and shut off the water supply before beginning. Wear work gloves to protect your hands. Drain any excess water from the washer before starting — the tub and hose still hold water that will spill out when you disconnect the hose, so have towels and a shallow pan ready. Pull the washer away from the wall to access the panels (on many models you can leave the water supply hoses connected and just unplug the electrical cord). The hose is accessed by removing the rear panel: remove the screws (often 4) securing the rear panel to the back of the washer and set the panel aside. On some front-load models, the top panel is removed instead — remove the top panel bracket screws, slide the top toward the rear, and lift it off. Locate the tub-to-pump hose connecting the outer tub to the drain pump. Photograph the hose routing and clamp positions before disconnecting. Use slip-joint pliers to squeeze and slide back the spring hose clamps at each end of the hose (and loosen any center clamp with a screwdriver). Pull the old hose straight off both connections. Note: on some models the clamp on the pump differs from other nearby hose clamps — mark them so you reinstall each in the right spot. Install the new AAS73229402 hose, seating it fully onto both the tub and pump fittings, and secure the clamps in their original positions using the existing clamps. Make sure the hose is seated all the way on and the clamps are secure — a hose that isn't fully seated will leak and make a large mess. Reinstall the panel, push the washer back into place, restore power and water, and run a rinse/spin cycle to test drainage and check for leaks. Tip: some people find it easier to tip the washer up a few inches on a couple of 2x4s for better access. Tools needed: Phillips screwdriver, slip-joint pliers, towels, shallow pan, work gloves. Frequently Asked Questions There's a puddle under my LG washer — is this hose the cause? It's one of the most common causes, yes. The tub-to-pump hose carries water under pressure from the tub to the drain pump, so when it cracks, splits, or develops a porous spot, water escapes during the drain cycle and puddles under the machine. Before ordering, inspect the hose and its connections: pull the washer out, remove the rear (or top) panel, and look for visible cracks, splits, or wet spots along the hose and at the clamps. Also check the drain pump itself and the other hoses, since a leak can come from several nearby points. If the tub-to-pump hose shows damage or the leak traces to it, this is the correct part. Many people replace the drain pump and hoses together as a "while you're in there" repair. What's the difference between the tub-to-pump hose and the drain hose? They're two different hoses. The tub-to-pump hose (this part, AAS73229402) is an internal hose that carries water from the outer tub to the drain pump inside the washer cabinet. The drain hose is the external hose that carries the water from the pump out of the washer to your standpipe, sink, or drain. If your leak is inside the cabinet or under the machine, it's often the internal tub-to-pump hose. If water is leaking where the external hose meets your drain, that's the drain hose. Make sure you're ordering the right one for your symptom. Can I use an aftermarket substitute hose instead? We recommend the exact OEM hose. Tub-to-pump hoses have to match the specific fit and internal diameter of your washer's tub and pump fittings to seal properly and drain correctly. Appliance technicians specifically caution against using unverified substitute hoses on LG washers because an incorrect fit or diameter can cause leaks or drainage problems. The AAS73229402 is the genuine OEM part with the correct dimensions for the models it fits, giving you a reliable, leak-free seal. If you're unsure whether this is the right hose for your model, send us your model number and we'll confirm. My washer won't drain fully and leaves standing water — is it this hose? It can be, though incomplete draining has a few possible causes. A tub-to-pump hose that has partially collapsed, kinked, or is leaking can reduce the water flow to the pump and leave water behind. But standing water is also commonly caused by a clogged pump, a blocked hose, or a failing drain pump. Inspect the tub-to-pump hose for kinks, sagging, cracks, and blockages first. Also check the drain pump inlet and clean out any debris. If the hose is damaged, replacing it with the AAS73229402 restores proper flow. If the hose is fine, the drain pump or a blockage is the more likely cause. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by LG to factory specifications. It is the exact same tub-to-pump hose (drain pump bellows assembly) installed in compatible LG and Kenmore LG-built washers from the factory — guaranteed fit, materials, and performance, sourced directly from the manufacturer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH11X39237 Genuine OEM GE Washer Drain Pump The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Genuine OEM Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH10X29537 Front Load Washer Door Fits specific GE Washer models. Description: This Washer Door is a Genuine OEM replacement part for GE washing machines. It is the main access point to the washer drum, allowing you to load and unload your laundry with a secure and tight seal during operation. 

Read more less

WH01X29528 Genuine OEM GE Washer Door Lock The WH01X29528 is a genuine GE OEM door lock assembly for GE front-load washers and select GE Ultrafast 2-in-1 combo washer/dryers. This is a safety mechanism, not just a switch: when the door closes, the lock engages automatically and secures the door shut for the full length of the cycle, only releasing once the control confirms it's safe to open. This prevents the door from being opened mid-cycle, which would otherwise let water and detergent spill out and create both a mess and a safety hazard. Rated 120VAC, 60Hz, 16A. Over time, the door lock can fail from physical damage or ordinary wear, and when it does, the symptoms can be wide-ranging: a washer that won't start because the control never confirms the door is locked, a cycle that stops partway through, a door that won't unlock at the end of a cycle, or in some cases excessive noise and shaking during operation since the lock also plays a role in keeping the door assembly seated correctly. It directly replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE. As a genuine OEM part, the WH01X29528 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH01X29528 Genuine OEM GE Washer Door Lock fixes GE front-load washers and GE Ultrafast combo washer/dryers where the door won't lock, the washer won't start, the door pops open or unlocks unexpectedly during the cycle, or the cycle stops partway through. 120VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, 0024000128GE. Before replacing, try a power reset — unplug the washer for 30 seconds and plug it back in — or hold Start/Pause for 15 seconds to command the control to release the lock; either can resolve a door stuck locked without needing a new part. Common Problems This Part Fixes Washer won't start because the door lock never confirms as locked Door lock fails to engage, or the door pops open after locking Door unlocks unexpectedly during the wash cycle Cycle stops or interrupts partway through Door won't unlock at the end of a completed cycle Excessive noise or shaking during operation related to a loose door seal Error code related to the door lock displayed on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, V13305, AGE26402, PD00060769, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock is compatible with select GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers, including model numbers such as: GFW510SCN0WW, GFW510SCN1WW, GFW510SCN2WW, GFW510SCN3WW, GFW510SCN4WW, GFW510SCN5WW GFW550SPN0DG, GFW550SPN2DG, GFW550SSN1WW GFW650SPN1SN, GFW650SPN2SN, GFW650SSN2WW, GFW650SSN3WW GFW655SSV0WW, GFW655SPV0WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS, GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW, GFW850SSN4WW, GFW850SSN5WW PFQ97HSPV0DS (GE Ultrafast 2-in-1 combo washer/dryer) PFW870SPV0RS, PFW870SSV0WW PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note: Always verify your full model number before ordering, since GE uses several different door lock assemblies across its front-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified locking mechanism and switch design Safety lock that secures the door shut for the full length of the wash cycle Resolves "won't lock," "won't start," "door pops open," and "cycle interruptions" symptoms caused by lock failure Rated 120VAC, 60Hz, 16A Direct drop-in replacement — matches the original mounting and harness connector Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE Compatible with GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH01X29528 Part Type Washer Door Lock Assembly Condition Genuine OEM Brand GE Application Front-Load Washers, GE Ultrafast Combo Washer/Dryers Voltage 120VAC Frequency 60 Hz Current Rating 16A Function Locks the door shut during the wash cycle; releases when the control confirms it's safe Quantity 1 door lock assembly Compatible Brand GE Installation Notes ⚠️ Unplug Washer Before Starting — Try A Power Reset First If The Door Is Stuck Locked Before replacing the part, try the simplest fixes first. Unplug the washer, wait 30 seconds, and plug it back in to let the control fully reboot — a simple power reset can release an operational lock and clear the problem without any disassembly. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds to command the control to unlock the door; this doesn't always succeed but is quick to try before opening up the washer. If the door is still locked and you need physical access, never work on the appliance while it's connected to power. Once you've confirmed replacement is necessary, disconnect power at the outlet or shut off the circuit breaker. Wear work gloves. Access is typically from the front, working around the door boot/gasket to reach the lock assembly mounted to the front panel. Photograph the wiring harness connector and mounting position before disconnecting anything. Disconnect the harness connector from the old lock, remove its mounting screws, and pull it free. Install the new WH01X29528 in the same position, secure the mounting screws, and reconnect the harness connector fully. Reseat the door boot/gasket if it was disturbed, restore power, and run a test cycle to confirm the door locks, stays locked through the cycle, and releases normally at the end. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My washer's door is stuck locked. Do I need to replace this part right away? Not necessarily — try the simple resets first. Unplug the washer for 30 seconds and plug it back in to let the control fully reboot, which can release an operational lock on its own. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds, which commands the control to release the lock electronically. These steps resolve many stuck-door situations without needing to replace the lock assembly at all. My washer won't start. Is that this part? It's a strong possibility. The control won't begin a cycle until it receives confirmation that the door is locked, so if this lock has failed and isn't sending that signal, the washer will simply refuse to start even though everything else appears normal. Try the power reset steps above first, then check for a door lock-related error code on the display before assuming the part has failed. I already replaced this lock once and it failed again. What should I check? If a newly replaced lock fails again relatively quickly, it's worth having the washer's control board checked, since a board that's sending incorrect signals to the lock can cause repeat failures that look like the lock itself is bad. It's also worth confirming the door boot/gasket is seated correctly, since a misaligned door can put uneven stress on the lock mechanism. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same locking mechanism, switch design, and harness connector as the door lock originally installed in your GE front-load washer or Ultrafast combo washer/dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5220FR2006H Washer Hot Water Inlet Valve - Compatible with LG, Kenmore Product Description Ensure proper water flow with the replacement 5220FR2006H Washer Hot Water Inlet Valve. This replacement water inlet valve is designed for select LG and Kenmore front-load and top-load washers, featuring one solenoid to control hot water entry into the drum. It addresses issues like no water flow, leaks, improper filling, or error codes, offering a cost-effective alternative to OEM parts. Note: Includes one water inlet valve with one solenoid. Disconnect power and water supply before installation. Check water supply lines and valve filters for blockages to ensure optimal performance. Replaces part numbers: 5220FR2006H, 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AH3527427, EA3527427, PD00001765, EAP3527427, AP4441935, PS3527427. Compatibility: Compatible with models including but not limited to: LG: WM2016CW, WM2077CW, WM2277HW, WM2455HW, WM2487HRM, WM2601HW, WM2701HV, WM2801HWA, WM3070HWA, WM3470HWA, WM8000HVA, WM9000HVA Kenmore: 796.40272800, 796.41022900, 796.41028900 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG and Kenmore front-load and top-load washers. 💧 Specifications: replacement water inlet valve with one solenoid, 120V, 60Hz. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves no water flow, leaks, improper filling, or error codes. Product Specification Part Number: 5220FR2006H Component Type: Washer hot water inlet valve Material: High-grade plastic and metal Electrical Specs: 120V, 60Hz, one solenoid. Mounting: Screw-mounted near washer water inlet Operating Conditions: Suitable for high-pressure water supply environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 5304528029 Washer Water Valve Dispenser Valve Gaskets are Not Included Washer water inlet valve. 5 Solenoid Coils, 5 Outlets Fits Specific Electrolux, Frigidaire front load washer models. Replaces Part Numbers:5304528029, 5304514790, 5304522534, AP7014477, PS16544354. Description: This Water Valve is a replacement part for specific Electrolux, Frigidaire washing machine models. This part controls the entry of water into the washer during the wash and rinse cycles. Common causes of a bad valve include mineral deposits from hard water, electrical issues, or general wear and tear over time.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

Genuine Whirlpool OEM Whirlpool WP8577374 Washer Genuine OEM Transmission Shaft Seal Genuine OEM center shaft / basket drive tube seal for select Whirlpool-built top-load washers and laundry centers. Product Overview The Whirlpool WP8577374 Washer Transmission Shaft Seal is a genuine OEM sealing component used in the center drive area of compatible washers. It is also described as a center shaft seal or basket drive tube seal. This seal helps keep wash water from leaking into the basket drive tube / gearcase area. A worn or damaged seal may allow water or dark oily residue to appear around the center shaft area. Quick Answer WP8577374 is a Genuine Whirlpool OEM washer center shaft / basket drive tube seal. It replaces original part number 8577374 and is used on many Whirlpool-built direct-drive washers sold under Whirlpool, KitchenAid, Roper, Estate, Maytag, Amana, Admiral, Crosley, and Kenmore brands. Common Problems This Part May Fix Water leaking around the center shaft area Water entering the basket drive tube Dark or oily-looking residue near the center of the washer Seal deterioration discovered during transmission or basket-drive service Preventive replacement during a major centerpost or gearcase repair Replaces and Cross-References WP8577374, 8577374, 4438792, AP6013519, AWP49372, PD00045466, PS11746745. Cross-reference numbers are provided for identification. Always verify the complete washer model number before ordering. Compatibility Fits select Whirlpool-built washers and laundry centers. Compatible model examples include: 3RGSC9400SL0 3XLSQ7533JQ4 KAWS850LQ2 CAM2752TQ0 7MMMS0120VM0 110.20522900 WTW5505VQ0 110.28762700 7MWT96540ST2 7MMSE1000TW0 ETW4400WQ1 MGT3800XW3 Important: This is only a partial compatibility list. Confirm your full model number because Whirlpool-built washers can use several different shaft, stem, centerpost, and transmission seals that are not interchangeable. Key Features Genuine Whirlpool OEM replacement part Center shaft / basket drive tube sealing component Helps prevent wash water from entering the drive tube area Direct replacement for original part 8577374 Used on many Whirlpool-built direct-drive washer platforms Product Specifications Manufacturer Part Number WP8577374 Brand Whirlpool Part Type Transmission / Center Shaft Seal Alternate Description Basket Drive Tube Seal / Centerpost Seal Condition New Part Quality Genuine OEM Replaces 8577374 Application Washer Center Drive / Basket Drive Tube Package Quantity 1 Seal Installation Notes Unplug the washer and shut off the water supply before service. Disassembly of the basket, drive components, or gearcase area may be required depending on model. Remove the old seal carefully to avoid damaging the sealing surface or drive tube. Clean and inspect the shaft/tube sealing surface before installing the new seal. Install the seal squarely and to the correct depth following the model-specific service procedure. Inspect related tub, centerpost, and transmission seals while the washer is disassembled. Service note: WP8577374 is not the same part as WP8577376 or WP91939. These seals are used in different locations. Verify the part number required for your exact washer before installation. Frequently Asked Questions Is WP8577374 a Genuine Whirlpool OEM part? Yes. WP8577374 is a genuine Whirlpool replacement seal. What does this seal do? It helps prevent wash water from leaking into the basket drive tube / center drive area of the washer. Does WP8577374 replace 8577374? Yes. WP8577374 is the current Whirlpool replacement for original part number 8577374. Is this the same as WP8577376 or WP91939? No. Although all are washer shaft/sealing components, they serve different locations and should not be substituted unless your model-specific parts documentation calls for that number. Shop With Confidence Order by complete model number whenever possible. Correct fit is especially important for washer centerpost and transmission sealing components. Genuine Whirlpool OEM Direct Replacement Model Verification Recommended Compatibility Support

Read more less

XPARTCO MFG63099101 Washer Door Strike (Door Lock Hook) The XPARTCO MFG63099101 is an aftermarket replacement washer door strike — also called a door lock hook or door latch hook — compatible with a wide range of LG front-load washers and Kenmore 796-series washing machines. The door strike is the metal hook component mounted on the inside edge of the washer door. When the door closes, the hook enters the door lock switch on the front panel and engages the electromagnetic lock mechanism, signaling the control board that the door is closed and locking it for safe operation during wash and spin cycles. Without an intact door strike, the lock can't grip anything, and the washer will not start. When the strike breaks — typically from repeated use, sudden impact, or stress over thousands of door cycles — the washer will not start, may stop mid-cycle, may display DE1 or DE2 error codes, leak water around the door, or fail to lock altogether. It directly replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132. Important: replacing the strike requires removing the inside door panel to access the hook — note that the inner glass insert is loose during disassembly and must be handled carefully. Often replaced alongside the matching door lock switch (EBF61315802, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO MFG63099101 Washer Door Strike fixes LG and Kenmore 796-series front-load washers where the door won't lock, won't start, stops mid-cycle, displays DE1 or DE2 errors, or leaks at the door. Metal hook attaches to the inside of the washer door — engages the lock switch when the door closes. Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132. Often paired with the door lock switch (EBF61315802, sold separately). Common Problems This Part Fixes Washer door not latching properly — strike broken or worn down Washer not starting because the door isn't detected as locked Washer stopping mid-cycle due to a door fault DE1 or DE2 error codes displayed on the control panel Minor water drips or leaks around the door during operation — door not sealing because the strike isn't fully engaging Door strike visibly broken, chipped, or missing on the inside edge of the door Door not staying closed — strike worn from repeated impact Washer not powering on Replaces Part Numbers This washer door strike directly replaces the following OEM and cross-reference part numbers: MFG63099101, 2759645, AGF77417823, PD00046132, EAP8752721, AP5787149, PS8752721. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the number printed on your original door hook may be a production batch code rather than the OEM part number — this does not affect fit. Compatibility This door strike is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3170CW/00, WM3180CW series LG front-load washers — WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HVA/01, WM3370HWA, WM3370HWA/01, WM3370HWA/00 series LG front-load washers — WM3400CW, WM3500CW, WM3500CW/00, WM3555HWA, WM3555HWA/00 series LG front-load washers — WM3570HVA, WM3570HVA/00, WM3575CW series LG front-load washers — WM3600HVA, WM3600HWA, WM3600HWA/00, WM3670HRA, WM3670HRA/00, WM3670HVA, WM3670HWA series LG front-load washers — WM3700HVA, WM3700HWA, WM3770HVA, WM3770HWA series LG front-load washers — WM3900HBA, WM3900HWA series LG front-load washers — WM4000HBA, WM4000HWA, WM4270HVA, WM4270HVA/00, WM4370HKA, WM4370HWA series Kenmore / Sears washers — 796-series (79641162410, 79641162411, 79641262610, 79641283310, 79641283311, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641482410, 79641482411, 79641483410, 79641483411, 79641582410, 79641582411, 79641583211, 79641583410, 79641583411, 79641962610, 79641963610 and many related models) Note: If both the door strike (MFG63099101) and the door lock switch (EBF61315802) have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new strike. Always verify your model number before ordering. Key Features Metal door strike (door lock hook) — mounts to the inside edge of the washer door and engages the door lock switch when the door closes Resolves DE1 and DE2 error codes when caused by a broken door strike on compatible LG and Kenmore washers Restores the proper engagement between the door and latch assembly for a firm, consistent connection every cycle Durable metal construction — designed to withstand repeated opening and closing impact Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132 Compatible with LG WM1388, WM3050, WM3170, WM3270, WM3370, WM3500, WM3570, WM3600, WM3670, WM3700, WM3770, WM3900, WM4000, WM4270, WM4370 series and Kenmore 796-series front-load washers Often replaced together with the door lock switch (EBF61315802, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number MFG63099101 Part Type Washer Door Strike (Door Lock Hook / Latch Hook) Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore LG-built platform) Location Inside edge of washer door Material Metal Often Paired With Door Lock Switch (EBF61315802, sold separately) Error Codes Resolved DE1, DE2 (when caused by broken strike) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Don't Drop the Inner Glass Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a broken strike, use a putty knife to pry the white latch on the door lock through the bottom service opening to release the door. With the door open, locate the screws around the perimeter of the inner door panel. Remove the screws to release the inner door panel from the outer frame. Important: the inner glass insert is loose once the panel is unscrewed — support the glass with one hand as you pry the panel away to prevent it from falling out and breaking. Note the orientation of the old door strike (the direction it points and how it's seated). Use needle-nose pliers or tweezers to pull out the retaining pin holding the old strike in place, then remove the broken strike. Install the new MFG63099101 strike in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Reinsert the retaining pin to secure it. Carefully reposition the glass insert into the door, reinstall the inner door panel, and tighten the screws. Restore power and run a test cycle to confirm the door locks properly and there are no leaks. Tools needed: Phillips screwdriver, needle-nose pliers or tweezers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door strike and the door lock switch? These are two separate parts that work together to lock the washer door. The door strike (MFG63099101) is the metal hook attached to the inside edge of the washer door — when the door closes, the hook is what physically enters the lock assembly. The door lock switch (EBF61315802) is the assembly mounted on the front panel just inside the door opening — it contains the electromagnetic mechanism that grips and locks the strike, and the electrical sensor that tells the control board the door is closed. If the strike is broken, the lock has nothing to grip and the washer won't start. If the switch is broken, the strike can still enter the slot but the lock won't engage or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing strike has broken off inside the lock or the lock won't release, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the strike installation. Always disconnect power from the washer first. The number on my old strike doesn't match — is it still compatible? In many cases, yes. LG sometimes prints production batch codes on door strikes that look like part numbers but don't match the official OEM part number. As long as your washer's parts diagram lists MFG63099101 (or one of its cross-references: AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132), this strike is the correct fit. If you're unsure, contact our support team with your washer model number and we'll verify before you order. Should I replace the door lock switch (EBF61315802) at the same time? Not always, but often. The strike and the lock switch work together as a pair — if one is worn, the other has typically experienced the same load over thousands of cycles and is approaching the end of its service life. When a broken strike is the cause of the failure, examine the lock switch when the panel is open: if the lock mechanism shows visible wear, doesn't grip the new strike firmly, or has corroded contacts, replace it at the same time. Since the door is already partially disassembled and you have the washer apart, doing both at once saves a second repair session. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal to match the dimensions, mounting configuration, and lock-engagement function of the original MFG63099101 door strike used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less