Search results for "dryer thermostat"

XPARTCO WE04X24719 Dryer Start Button The XPARTCO WE04X24719 is an aftermarket replacement power and start button assembly for GE and Hotpoint dryers. You push it to power up the dryer's controls and begin the drying cycle. When the button is cracked, stuck, or no longer registers a press, the dryer won't start, even though the rest of the machine is fine. This is a direct-fit aftermarket replacement for the original GE button assembly. The button mounts through the control panel and onto the switch shaft behind it, so if the dryer still won't start with a new button, the push-to-start switch itself may also need to be checked. Quick Answer The XPARTCO WE04X24719 Start Button fixes a GE or Hotpoint dryer whose start button is broken, stuck, or doesn't start the dryer when pressed. Classic symptom: you press start and nothing happens, or the button feels loose, cracked, or no longer springs back. Common Problems This Part Fixes Dryer won't start when the start button is pressed Start button is cracked, broken, or missing Button feels loose, stuck, or doesn't spring back Button no longer lines up with the switch behind the panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This start button assembly directly replaces the following part number: WE04X24719, AGE24894, AP6034220, EAP11766637, 4587500, PD00046802, PS11766637 No other GE part numbers were confirmed for this button. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This start button is listed for GE and Hotpoint dryers, including these examples: 5TX62E9ST0WS, ETD48EASW0WB GTD33EASK0WW, GTD42EASJ2WW, GTD48EASW0WB GTD45GASJ0WS (gas) Note: The models above are a sample of about 40 listed dryers, not a full list. This is the button assembly that fits onto the switch shaft, not the switch itself. Confirm your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket power and start button assembly for GE and Hotpoint dryers Restores a working push-to-start button Fits electric and gas dryer models Straightforward repair, typically 30 minutes to 1 hour Product Specifications Part Number XPWE04X24719 OEM Part Number WE04X24719 Part Type Dryer Power and Start Button Assembly Condition Aftermarket Replacement Application GE & Hotpoint Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. The button is held to the switch behind the control panel, so you will need to remove the back panel, the wires, and the switch to take the old button out through the panel, as shown in your model's service guide. Note where each wire connects before removing it. Fit the new button through the panel onto the switch shaft, then reassemble in reverse order. Frequently Asked Questions My dryer won't start when I press the button. Is this the part I need? If the button is cracked, loose, or doesn't press the switch, yes. If the button looks fine, the push-to-start switch behind it, the door switch, or a thermal fuse can cause the same symptom, so check those too. Does this include the switch? This listing is for the button assembly that fits onto the switch shaft, not the switch. If the switch itself has failed, it is a separate part. Do I need to take the dryer apart? Yes. The button is installed through the control panel, so the back panel, wires, and switch have to come off to replace it. Customers report about 30 minutes to 1 hour. Will this fit my dryer? It is listed for many GE and Hotpoint dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP8182528 Dryer Genuine OEM Heating Element Replaces Part Numbers: WP8182528, 8182528, 1065644, AP6011812, PS11745011.  Description: Upgrade your dryer's heating element with the WP8182528 Genuine OEM Heating Element. This high-quality replacement part will ensure efficient and reliable heat distribution, giving your clothes that perfect dry every time. Trust in its durability and compatibility with your dryer model.

Read more less

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat The WP4449751 is a Genuine OEM Whirlpool replacement oven high limit thermostat compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens, wall ovens, microwave-oven combinations, and ranges. The high limit thermostat is a critical safety device mounted near the oven cavity — it continuously monitors the oven's temperature and cuts off electrical power to the heating element if the oven exceeds its safe operating temperature. When the oven temperature drops back to normal, the thermostat closes and allows normal operation to resume. This backup safety layer protects against fires, damage to the oven, and unsafe cooking conditions when the main temperature control fails. Rated to trip at approximately 335°F (170°C). Common causes for the high limit thermostat to trip include a faulty control board, cooling fan failure, blocked ventilation, poor door sealing, disrupted air circulation, or an abnormal self-cleaning cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the WP4449751 directly replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549. Installs in 30–45 minutes with basic hand tools by experienced DIYers. This is a safety component in a 240V oven circuit — proceed only if you're comfortable with high-voltage electrical work, or call a qualified appliance technician. Quick Answer The WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore ovens with symptoms including oven not heating, oven overheating, uneven heating, oven failing to start, and self-clean door won't unlock after cycle. 335°F (170°C) trip temperature — cuts off power to heating element on overheat, then resets when temperature returns to normal. Genuine OEM. Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, AH11742549. Compatible with WOS/WOD wall ovens, KOSE/KODE/KOCE series, JJW/JMW/JDRP/JDR series, and many more. Common Problems This Part Fixes Oven not heating at all — high limit thermostat tripped open Oven overheating — thermostat failing to trip when needed (rare failure mode) Inconsistent oven temperatures leading to undercooked or overcooked food Oven fails to start when powered on Oven door won't unlock after a self-cleaning cycle completes Uneven heating — hot spots or cold spots inside the oven cavity Oven cuts off heat mid-cycle without reaching set temperature F-code or thermostat-related error displayed on the control panel Multimeter continuity test on the thermostat shows an open circuit at room temperature Visible damage or discoloration on the thermostat housing from a prior overheat event Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven high limit thermostat directly replaces the following OEM and cross-reference part numbers: WP4449751, 4449751, 1550872, AP6009390, AWP47600, EAP2375382, PD00025977, PS11742549 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high limit thermostat is compatible with select ovens, wall ovens, ranges, and microwave-oven combinations from the following brands: Whirlpool wall ovens — WOS series (WOS31ES0JS, WOS51EC0AS, WOS51EC0HS, WOS51EC7HW02, WOS51EC7HW21, WOS72EC0HS/HV, WOS72EC7HS/HV, WOS92EC0/EC7 all revisions, WOS97ES0ES series) Whirlpool double wall ovens — WOD series (WOD51EC0AW03, WOD51EC7HS, WOD93EC7AS) Whirlpool combination wall ovens — WOC54EC0/EC7 series KitchenAid wall ovens — KOSE, KODE, and KOCE series (KOSE500ESS, KODE500ESS, KOCE500ESS, KOCE500EBL00/EBL01/EBL02/EBL04/EBL05) Jenn-Air wall ovens — JJW, JMW, JDRP, and JDR series (JJW2427DB/DS 00/01, JJW2430DS, JJW3430DS, JMW2430DS, JDRP430HL/HM 00/01, JDRP430WP00, JDRP436HL/HM/WP series, JDRP536HL/HM/WP series) Maytag wall ovens and ranges (select models) Amana wall ovens (select models — AWO6313SFB00/02, AWO6313SFS00/02, AWO6313SFW00/02) KitchenAid ranges — KDRS407 series (KDRS407VBK01, KDRS407VBU01, KDRS407VSS00) Whirlpool ranges — IBD350DS00, IBS300DS00, IBS350DS00 series Magic Chef, Admiral, Norge, Roper wall ovens (select Whirlpool-built models) Kenmore / Sears wall ovens (select Whirlpool-built models) Suitable for single or double electric wall ovens and microwave-oven combination units Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance High limit thermostat (safety switch) — cuts off power to the oven's heating element when temperature exceeds 335°F (170°C) to prevent overheating damage or fire Auto-reset design — closes and restores normal operation when the oven temperature returns to safe range Precision-calibrated to Whirlpool factory specifications for accurate trip temperature and reliable safety response One-year Whirlpool warranty on Genuine OEM parts Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549 Compatible with Whirlpool WOS/WOD/WOC series, KitchenAid KOSE/KODE/KOCE series, Jenn-Air JJW/JMW/JDRP/JDR series, plus Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens Fits single wall ovens, double wall ovens, ranges, and microwave-oven combination units Resolves "oven won't heat," "overheating," "uneven heating," "self-clean door stuck locked," and "won't start" symptoms when caused by a failed high limit thermostat For experienced DIYers or qualified appliance technicians — this is a safety component in a 240V oven circuit Installation typically takes 30–45 minutes with basic hand tools Product Specifications Part Number WP4449751 Part Type Oven High Limit Thermostat (Safety Switch) Condition Genuine OEM Application Wall Ovens, Ranges, Microwave-Oven Combinations (Whirlpool platform) Trip Temperature 335°F (170°C) Type Auto-Reset (closes when temperature returns to safe range) Warranty One-Year Whirlpool Warranty (Genuine OEM) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Turn Off Power at Breaker Before Starting — This Is a 240V Oven Circuit — Wear Work Gloves Disconnect power at the household breaker before beginning — this is a 240V circuit and there is a serious risk of electrical shock if power is not fully disconnected. Verify power is off with a voltage tester before touching any wiring. Wear work gloves and safety glasses. Allow the oven to cool completely before beginning (several hours after any recent cooking). The high limit thermostat is typically mounted on the rear or side of the oven cavity, accessed by removing the back panel of the appliance (for freestanding ranges) or the front trim/service panel (for wall ovens). The exact location varies by model — consult your appliance's service diagram before starting. Photograph all wire connections and mounting details before disconnecting anything. Disconnect the wire terminals from the old thermostat (typically two spade-terminal wires). Remove the mounting screws or clips holding the thermostat to the oven cavity, and lift it out. Install the new WP4449751 in the exact same position and orientation — the thermostat must be in good thermal contact with the oven cavity to function correctly. Secure the mounting hardware and reconnect the wires to their correct terminals. Reinstall the access panels. Restore power at the breaker and test the oven — start with a low-temperature bake cycle to confirm normal heating operation before running a high-temperature or self-clean cycle. Tools needed: Phillips screwdriver, 1/4" nut driver, voltage tester (essential), work gloves, safety glasses. Frequently Asked Questions Why did my high limit thermostat trip in the first place? A high limit thermostat trips because the oven exceeded its safe operating temperature — meaning something upstream in the temperature control chain failed to shut off the heating element when it should have. Common causes are: a failed oven control board (relay stuck closed), a failed cooling fan (allowing the oven cavity or electronics to overheat), blocked or restricted ventilation, poor door sealing (letting the cavity overheat), disrupted air circulation, or an abnormal self-cleaning cycle. Before installing the new thermostat, investigate and address the underlying cause — otherwise the new thermostat will trip again in short order. Also inspect the ventilation, oven door gasket, and cooling fan while you have the appliance open. What's the difference between a high limit thermostat and the operating thermostat? These are two different components serving two different roles. The operating thermostat (or the oven control board with its temperature sensor) is the primary component that maintains the oven at your set temperature by cycling the heating element on and off during normal operation — it opens and closes at your selected temperature (e.g., 350°F). The high limit thermostat (WP4449751) is a backup safety device that only trips when the oven temperature far exceeds normal operation (335°F over the cavity's safe threshold), typically because the operating thermostat or control has failed. If the high limit thermostat trips, both need to be checked — the operating thermostat may also need replacement. Does the high limit thermostat reset itself, or does it need to be replaced after tripping? The WP4449751 is an auto-reset thermostat — it closes automatically once the oven cools back to a safe temperature, allowing normal operation to resume. If your oven is heating normally again after cooling, the thermostat is likely still functional (the underlying overheating cause needs investigation). However, if the thermostat has failed permanently open — often the result of repeated overheat events or age — it will need replacement. Test with a multimeter set to continuity: a working thermostat shows continuity at room temperature. If it reads open (infinite resistance) when cold, it has failed and needs replacement. Why does my self-cleaning cycle leave the oven door locked and the oven won't heat? This is a classic symptom of a high limit thermostat that tripped during the self-clean cycle. Self-cleaning cycles run at extreme temperatures (800–1000°F) and stress every component in the oven — if the ventilation, door gasket, or cooling fan can't keep up, the high limit thermostat will trip open. Once tripped, the oven can't heat OR unlock the self-clean door lock mechanism, leaving the door stuck closed. Once the thermostat cools and closes (or is replaced), the door lock releases and normal operation resumes. If self-clean cycles routinely trip the thermostat, investigate whether the ventilation, cooling fan, or door gasket are causing the problem. Can I do this repair myself, or should I hire a technician? Replacing an oven high limit thermostat is a manageable DIY repair for someone comfortable with mechanical work and electrical connections, but this is a 240V circuit and the thermostat is a safety component — any error can create a serious safety risk. If you have experience with appliance repair, follow the safety precautions carefully (breaker off, voltage tester, correct thermostat orientation), and can confirm the wiring connections are secure, this is a feasible DIY. If you've never worked with 240V appliance circuits before, hiring a qualified appliance technician is the safer option. Also identify and address whatever caused the original overheat event — otherwise the new thermostat will trip again. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same high limit thermostat installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens from the factory — guaranteed fit, materials, and performance. Backed by Whirlpool's one-year warranty on Genuine OEM parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP697772 Dryer Blower Wheel The WP697772 is a genuine OEM blower wheel from Whirlpool for Whirlpool-built dryers and washer-dryer combos sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral names. The blower wheel attaches to the drive motor shaft and moves air over the heat source, through the drum, and out the exhaust vent. When the wheel wears, cracks, loses a fin, or comes loose on the shaft, the dryer gets noisy and airflow drops, so clothes take longer to dry. This is a genuine OEM part, not an aftermarket equivalent, so the fit and balance match the original. If your dryer is only noisy, check the blower for lint buildup first, since a clogged wheel can sound like a failing one. Quick Answer The Genuine OEM WP697772 Blower Wheel fixes a Whirlpool-built dryer that is noisy, has weak airflow, or takes too long to dry because the blower wheel is worn, cracked, or damaged. Genuine OEM from Whirlpool. Classic symptom: a rattling, thumping, or squealing noise from the back of the dryer, with damp clothes at the end of a normal cycle. Common Problems This Part Fixes Dryer noisy, with rattling or thumping from the blower area Weak airflow, or clothes taking too long to dry Visibly cracked, chipped, or broken blower fins Blower wheel loose or slipping on the motor shaft Wheel worn out over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This blower wheel replaces the following part numbers: WP697772, WPW10211915, 697772, W10211915, 687613, AP6010627, AWP48289,EAP11743811,  FIX11743811, OEM18031890, PD00003053, PS11743811 These are Whirlpool's un-prefixed and earlier numbers for this blower wheel. If your old wheel or parts diagram shows any of them, match against this list. Compatibility This blower wheel is listed for dryers and washer-dryer combos from: Whirlpool, including CEE2760KQ0, WED9470WW1, and WED9400ST1 Kenmore, including 11060052990, 11060056990, and 10687884100 Maytag, including YMEDX700XL0 and MGDX700AG0 KitchenAid, Amana, Crosley, Inglis, and Admiral Note: The model list above is only a sample, since this wheel fits many more models. Confirm fit by matching the number on your old wheel or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM Whirlpool blower wheel, not an aftermarket equivalent Restores quiet, full airflow through the drum and exhaust Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers and combos Straightforward replacement, typically 15–60 minutes with hand tools Product Specifications Part Number WP697772 OEM Part Number WP697772 Part Type Dryer Blower Wheel Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Family Dryers & Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Wear work gloves. Following your model's service guide, remove the front cover to reach the blower housing, then the back cover to access the motor shaft. Hold the motor shaft steady while you unscrew the retaining nut and pull off the old wheel. Reviewers report that the nut is left-hand threaded on these dryers, so check the thread direction before forcing it. Thread the new wheel on while holding the shaft, tighten it, and replace the covers. Clean the blower housing and exhaust duct of lint while you have the dryer open, and inspect the new wheel on arrival for damage. Frequently Asked Questions My dryer is noisy. Is this the part I need? Possibly. Before replacing the wheel, check whether it is clogged with lint, which can cause noise and imbalance. If the wheel is clean but cracked, chipped, or loose on the shaft, replace it. Also check the drum rollers and idler pulley, which can make similar sounds. Is the nut on the shaft left-hand threaded? Reviewers report that it is on these dryers, so turn it the opposite way to a normal nut when removing the old wheel. Check on your dryer before applying force. My old wheel is marked 697772 or W10211915. Will this work? Yes. Both numbers are on the Replaces list. If you're unsure, contact our support team with your model number and we'll confirm. Is this a genuine Whirlpool part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DE47-20059B Microwave Genuine Thermostat Fits specific Samsung microwave models. Replaces Part Numbers: DE47-20059B, 2079767, DE47-20059A, OEM18320450, AP4580112, PS4226453.Description: This Microwave Thermostat is an essential component for maintaining the optimal performance of your Samsung microwave. This genuine OEM part ensures precise temperature control, helping your appliance operate safely and efficiently. Designed specifically for Samsung microwave models, the thermostat guarantees a perfect fit and seamless integration with your existing system. By replacing a faulty or damaged thermostat with this high-quality part, you can restore your microwave's functionality and extend its lifespan. The Microwave Thermostat is built to withstand the demands of everyday use, providing reliable performance and consistent heating results. Easy to install, this thermostat allows you to perform repairs yourself, saving you time and the cost of professional service. Enhance your microwave reliability and enjoy peace of mind knowing you are using a genuine OEM part that delivers both quality and durability.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag Product Description Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use. Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Maytag: YNED4655EW, YIED4671EW Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0 Crosley: VDEW6511RW0, VED6505GW0 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration. 💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation. 🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues. Product Specification Part Number: WPW10420741 Component Type: Dryer push to start switch Material: Plastic and brass/stainless steel Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST) Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

W11025156 Genuine OEM Whirlpool Dryer Heating Element The W11025156 is a genuine Whirlpool OEM heating element for Whirlpool, Kenmore, and Maytag electric dryers. This element is the source of virtually all the heat in the dryer: it converts electrical energy into heat, which the blower then circulates through the drum to dry your clothes. Even heat distribution from a properly functioning element is what keeps drying times consistent and prevents the dryer from having to run longer cycles to compensate. Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. Symptoms of a failing element include clothes taking too long to dry, clothes coming out cold, or the dryer not heating at all. This part is also essential for preventing overheating, since a properly functioning element operates within its designed parameters rather than drawing excess current trying to compensate for a partial failure. It directly replaces W10608823. Quick Answer The W11025156 Genuine OEM Whirlpool Dryer Heating Element fixes Whirlpool, Kenmore, and Maytag electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Replaces W10608823. Before replacing, clean out or inspect your exhaust venting — restricted airflow is a common cause of premature heating element failure, and a fresh element installed into a clogged system is likely to fail again. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Dryer not drying laundry despite completing a normal cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: W11025156, W10608823, 4461512, W10608823, AP6037386, AWP42261, EAP11770230, PD00034419, PS11770230. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore and Maytag dryers built on the same platform, including model numbers such as: MEDB855DC2, MEDB955FC1, MEDB955FW1 (Maytag) YWED8000DW1, YWED8500DW1, WED9500EC0, WED9500EW0, WED8700EC2 Kenmore 11061632610, 11061632611, 11061632612, 11061633610, 11061633611 Kenmore 11068132411, 11068132412, 11068132413, 11068133411, 11068133412, 11068133413 Kenmore 11069132411, 11069132412, 11069132413, 11069133411, 11069133412, 11069133413 Kenmore 110C61633610, 110C68132413 Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified coil design and electrical rating Converts electrical energy into heat, circulated through the drum by the blower Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Ensures even heat distribution for consistent drying performance Direct drop-in replacement — no modification required Replaces W10608823 Compatible with Whirlpool, Kenmore, and Maytag electric dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11025156 Part Type Dryer Heating Element Condition Genuine OEM Brand Whirlpool Function Generates heat to dry clothes, circulated through the drum Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element Compatible Brands Whirlpool, Kenmore, Maytag Installation Notes ⚠️ Unplug Dryer Before Starting — Clean The Vent While You Have The Panel Open Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the back panel: a 1/4" ratchet with a 5/16" socket handles most of the screws, and using a socket adapter on a screw gun can speed up removing and reinstalling the panel, since there are several screws to deal with. With the panel off, locate the heating element in the duct housing. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new W11025156 in the same position, reconnect the wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" ratchet, 5/16" socket, work gloves. Frequently Asked Questions My dryer runs a full cycle but the clothes are still wet. Is this the heating element? It's a strong possibility, especially if you've noticed drying times gradually getting longer before the dryer stopped heating altogether. One customer described exactly this symptom — "dryer not drying laundry" — and resolved it with this exact replacement element. Do I need any special tools for this repair? Just basic hand tools. A 1/4" ratchet with a 5/16" socket handles the back panel screws on most models. Using a socket adapter on a screw gun can speed up the process, since there are several screws to remove and reinstall on the back panel alone. Why does the listing recommend cleaning the vent during this repair? Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original coil design and electrical rating of the heating element originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM 279311 Dryer Igniter Kit and Bracket The Genuine OEM Whirlpool 279311 is the gas dryer igniter kit with mounting bracket. The silicon carbide igniter glows to light the gas burner and produce the heat that dries your clothes. When the igniter weakens or breaks, the dryer tumbles but doesn't heat, because the gas valve never gets the signal to light the burner. This is the original Whirlpool part. It is listed as a replacement for both round and flat igniters, so it covers a long list of older Whirlpool part numbers for gas dryers sold as Whirlpool, Kenmore, Maytag, and KitchenAid. Quick Answer The Genuine OEM 279311 Igniter Kit and Bracket fixes a gas dryer that spins but doesn't heat because the igniter has burned out or is too weak to open the gas valve. It is for gas dryers only. Classic symptom: the drum turns and the dryer sounds normal, but clothes come out cold and damp, and you never see the igniter glow. Common Problems This Part Fixes Gas dryer runs but doesn't heat Clothes come out damp after a full cycle Igniter never glows, or glows but the burner never lights Cracked, broken, or burned igniter Burner lights unreliably or only some of the time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This igniter kit directly replaces the following part numbers: 279311, 239233, 239300, 239302, 26000279311, 279185, 279311VP, 338899, 338900, 3389895, 340607, 3415, 343128, 41-311, 6-85211, 660991, 685211, 686590, 687399, 691039, 8113, 99912719, AH334180, DE351, DE354, DE363, K35-166, AP3094138, AWP39784, EAP334180, EA334180, PD00002344, PS334180 These numbers span several generations of Whirlpool's own part numbering for this igniter as dryer models were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This igniter kit is for Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers, including these examples: Whirlpool LGN1000HQ0, LGN1000HQ1, 7MWG66740SG0, 7MWGD72HEDW0 Maytag 7MMGDC300YW0, 7MMGDC410AW0 Kenmore 11097291110, 10687884100, 110279119, 1103401771 Note: This igniter is for gas dryers only. The models above are a sample, not a full list. One supplier lists the kit contents as a 3-inch flat igniter, mounting bracket, 4-inch wire lead and plug. Confirm your model number and the igniter style against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool gas dryer igniter kit with bracket Silicon carbide igniter that lights the gas burner Listed to replace both round and flat igniters Resolves no-heat problems caused by a failed igniter Fits Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers Product Specifications Part Number 279311 OEM Part Number 279311 Part Type Gas Dryer Igniter Kit with Bracket Condition Genuine OEM Fuel Type Gas Dryers Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power and Shut Off the Gas Unplug the dryer and close the gas shutoff valve before beginning, and wear work gloves. Remove the panel that gives access to the burner assembly per your model's service guide, disconnect the igniter's wire connector, and remove the old igniter and bracket. The igniter is fragile, so handle it by the bracket and avoid bumping or squeezing the element. Install the new kit in the same position, reconnect the wires, then restore the gas and power and test the dryer for heat. If you smell gas at any point, stop, ventilate, and call your gas utility. Frequently Asked Questions My gas dryer spins but doesn't heat. Is this the part I need? A failed igniter is a common cause. If you run the dryer and never see the igniter glow, or it glows but the burner doesn't light, test the igniter for continuity. A bad coil on the gas valve or a thermal fuse can cause the same symptom, so check those too. Will this fit an electric dryer? No. This igniter is for gas dryers only. Electric dryers use a heating element instead. Why did my new igniter break? Silicon carbide igniters are fragile. Handle the new one by the bracket, and don't press or bump the element during installation. A weak or restricted gas supply or a faulty gas valve can also make igniters fail early. Will this fit my dryer? It is listed for many Whirlpool-built gas dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP W10185981 Dryer Timer – Replaces WPW10185981 – Compatible with Whirlpool, Kenmore, Maytag, Estate, and Roper Dryers Product Description Restore accurate dryer cycle timing with the ERP W10185981 Dryer Timer. This high-quality replacement controls the duration of drying, auto-sense, and cooldown cycles. It is responsible for controlling and managing the timing and sequence of the various drying cycles and functions. A failing timer may cause the dryer to stop mid-cycle, run too long, not start, or remain stuck on one setting. Replacing it with this reliable ERP timer ensures smooth, consistent cycle operation at a cost-effective price. Replaces Part Numbers WPW10185981, W10185981, 1481704, 418-095-20-B5, PD00004725, EAP11749830, AP6016540, PS11749830. Compatibility This replacement dryer timer fits select Whirlpool, Kenmore, Maytag, Amana, Estate, Roper, and Crosley dryers. Example compatible models include (but are not limited to):Whirlpool WED5300SQ0, Kenmore 110.65132411, Maytag MEDC200XW1, Estate EED4400WQ0. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM timing accuracy and electrical performance ⏱️ Restores Cycle Control – Regulates drying, auto-sense, and cooldown cycles 💰 Cost-Effective Alternative – Reliable performance without OEM pricing 🛠️ Direct-Fit Installation – Plug-in wiring harness and standard mounting 🛡️ Fixes Common Issues – Solves timer not advancing, dryer not starting, or cycles running too long 📐 Product Specification Part Number: W10185981 Component Type: Dryer Cycle Timer Material: Reinforced polymer housing with internal metal timing mechanism Mounting: Installs behind control panel Electrical Rating: Matches OEM specifications Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear control panel cover. Unplug the wiring harness from the old timer. Remove mounting screws and take out the old timer. Install the new ERP W10185981 timer in the same orientation. Reconnect wiring, reinstall the panel, and restore power. Test dryer cycles for proper operation. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate dryer timing — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WE4X750 Gas Dryer Igniter The XPARTCO WE4X750 is an aftermarket replacement flat igniter for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers, replacing GE part WE4X750 and cross-referencing 5303937186 and 4391996. The igniter sits in the burner assembly. It heats up when electrical current passes through it and lights the gas so the dryer can heat. When it wears out or stops glowing, the dryer may run but not heat. Check your model number before ordering, as gas dryers use several different igniters. Quick Answer The XPARTCO WE4X750 Gas Dryer Igniter replaces a worn or non-glowing igniter on a compatible gas dryer from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands. Replaces WE4X750, WE04X0750, 5303937186 and 4391996. Classic symptom: the dryer runs but does not heat, and the igniter doesn't glow. Other parts can cause the same symptom. Common Problems This Part Fixes Gas dryer not heating Igniter not glowing Worn igniter that no longer lights the burner Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer igniter directly replaces the following part numbers: WE4X750, WE04X0750, 276846, AGE25807, AH268196, AP2042796, EA268196, PD00001123, PS268196, 5303937186, 08001685, 08010845, 08015456, 1036069, 3281151, 5303281151, 8001685, F000134211, F134211-000, F134211000, F139743-000, F139743000, G139743-000, AFR17339, AH900236, AP3674313, EA900236, PD00000539, PS900236, Q000622141, Q622141, WQ622141, 4391996, 14211282, 3-4970, 3018, 304970, 41-311, 41-590, 4391996VP, AH373025, AP3109449, AWP39344, DE351, DE363, EA373025, K35-166, K35-455, PD00002514, PS373025 Gas dryers use several different igniters, and they are not interchangeable by number alone. If your old igniter shows a different number, contact our support team and we'll check whether it matches. Compatibility This igniter is listed for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers. Example GE and Hotpoint models that use WE4X750: GE DBL333GA0CC, DCL333GA0AA, DVL223GA0WW, DBL333GY0WW GE DCB330GB0KC, DCD330GY1AC, DH43GW0WW Hotpoint NVL333GY0AA Note: The models above are a small sample of the roughly 36 that retailers list for WE4X750, not a full list, and the example models are GE and Hotpoint. For other brands, confirm fit by your igniter's part number (such as 4391996 or 5303937186) and your model. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WE4X750 flat gas dryer igniter Lights the gas burner so the dryer can heat Installs in the dryer burner assembly Replaces the earlier GE number WE04X0750 and cross-references 5303937186 and 4391996 Product Specifications Part Number XPWE4X750 OEM Part Number WE4X750, 5303937186, 4391996 Part Type Gas Dryer Igniter (Flat) Condition Aftermarket Replacement Quantity 1 Igniter Application Select GE, Hotpoint, Whirlpool, Maytag, Frigidaire & Other Gas Dryers Installation Notes ⚠️ Disconnect Power And Shut Off The Gas Before Installing Unplug the dryer and shut off the gas supply before you begin, and wear work gloves. Remove the panel to reach the burner assembly, note how the igniter and its wiring connect, and remove the old igniter. Handle the new igniter carefully and install it in the same position. Reconnect the wiring, restore power and gas, and test the dryer. If you smell gas at any point, stop and contact a qualified technician. Frequently Asked Questions My gas dryer runs but doesn't heat. Is this the part I need? It can be, if the igniter has worn out and no longer glows. Other parts, such as the gas valve coils or thermal fuse, can cause the same symptom, so confirm the igniter is the problem before replacing it. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WE4X750. If you specifically need a genuine GE part, contact our support team. Can I use a different gas dryer igniter? Not by number alone. Gas dryers use several different igniters. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my dryer? It is listed for select gas dryers from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less