Search results for "leveling"

XPARTCO WH13X26637 Washer Water Valve The XPARTCO WH13X26637 is an aftermarket replacement quad water inlet valve for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models. This valve controls the flow of water into the washer from the household supply line, using two internal valves — each with its own wire terminals — to manage water flow and temperature blending for the wash cycle. When the control calls for a fill, the corresponding solenoid opens to admit water and closes once the correct level is reached. Rated 120V, 6/5W. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve produces a clear set of symptoms: the washer not starting, an error code related to water fill, or — one of the most common complaints — water continuing to drip into the tub between cycles even when the washer isn't running, since a worn internal seal can fail to shut off completely. It directly replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665. Quick Answer The XPARTCO WH13X26637 Washer Water Valve fixes GE top-load washers (and select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore models) that won't start, show a water-fill error code, or have water dripping into the tub between cycles. Quad valve design — 2 valves, each with its own wire terminals. 120V, 6/5W. Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, PD00037665. Dripping into the tub between cycles, even with the washer off, is a classic sign of a worn valve seal that isn't shutting off completely. Common Problems This Part Fixes Washer won't start Error code related to water fill displayed on the control panel Water dripping into the tub between cycles, even when the washer isn't running Washer filling slowly or only partially No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, 4546358, AGE26282, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X24058, WH13X26637-25PK, PD00037665 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, RCA, Café, and Kenmore washers built on the GE platform, including model numbers such as: GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS GTW685BPL0DG, GTW750CPL1DG, GTW720BSN0WS PTW605BPR1DG, PTW605BSR0WS, PTW605BSR1WS PTW700BPT0DG, PTW700BST0RS, PTW700BST0WS PTW705BPT0DG, PTW705BST0RS, PTW705BST0WS Note: This is a top-load washer valve, distinct from GE's front-load valves used on other GE washer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement quad water inlet valve — two valves, each with its own wire terminals Resolves "won't start," "water fill error code," and "dripping into the tub between cycles" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Rated 120V, 6/5W Replaces WH13X24058, 4546358, AP5999608, AP6282070, EAP11729480, EAP12171559, PS11729480, PS12171559, WH13X26637-25PK, AGE26282, and PD00037665 Compatible with GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair, typically 15 to 30 minutes Product Specifications Part Number XPWH13X26637 OEM Part Number WH13X26637 Part Type Washer Quad Water Inlet Valve Condition Aftermarket Replacement Application Top-Load Washers Voltage 120V Wattage 6/5 W Valve Design Quad — 2 valves, each with separate wire terminals Repair Difficulty Easy — 15 to 30 minutes Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, RCA, Café, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves at the wall before beginning. Wear work gloves. Unscrew the hot and cold supply lines from the bottom of the old valve, then carefully pull the valve assembly away from the wall for access. Photograph the wiring and hose connections before disconnecting anything, since this valve has two separate wire terminal sets and multiple outlet hoses. Remove the cover securing the valve in place, disconnect the electrical connectors and outlet hoses, and take out the old valve — the entire assembly typically comes out in one piece. Insert the new WH13X26637 into the same opening, making sure it fits tightly and securely, and secure it with screws. Reconnect all outlet hoses to their original positions, reconnect the electrical connectors fully, and put the cover back on. Reconnect the hot and cold supply lines, tightening securely. Turn the water supply back on and check for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: screwdriver, spanner, pliers or adjustable wrench, work gloves. Frequently Asked Questions Water keeps dripping into my washer tub even when it's not running. Is this the valve? Yes, this is one of the most common symptoms of a failing valve, and a well-documented one for this exact part. If you've already checked the hoses and confirmed they're not the source of the leak, a worn internal seal in the valve is the most likely remaining cause — the seal fails to shut off completely, letting a small amount of water continue dripping through even between cycles. Shutting off the water supply is a temporary workaround, but replacing the valve is the permanent fix. Why does this valve have two sets of wire terminals? This is a quad valve design, meaning it houses two separate internal valves in one assembly, each with its own electrical connection. This allows the washer to independently control different water functions — such as hot and cold fill — from a single combined unit rather than requiring two completely separate valve housings. Is this a top-load or front-load washer valve? This is a top-load washer valve, compatible with GE's GTW and PTW model series. It's a different valve design from the ones used on GE's front-load washer platforms, so confirm your washer type and model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the quad valve design, wattage, and connection type of the original WH13X26637 valve used in compatible GE, Hotpoint, Haier, Monogram, RCA, Café, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator cooling evenly with the XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor. This Fan Motor is a replacement component for specific LG, Kenmore refrigerator models. It operates the circulation fan located in the back of the refrigerator compartment, distributing cool air evenly throughout. The motor enables constant airflow across shelves and compartments to maintain consistent temperatures and humidity levels. Causes of a bad fan motor include failure of bearings or windings due to prolonged use. Replaces Part Numbers 4681JB1029A, EAU60694507, 1330410, 4681JB1010C, 4681JB1017A, 4681JB1017D, 4681JB1027A, EAU61762902, EAU41921810, PD00037982, EAP3523328, AH3523328, EA3523328, AP4438221, PS3523328.  Compatibility This replacement evaporator fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25960ST, LG LFX28968ST, and Kenmore 795.77543600. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to meet OEM airflow and reliability standards ❄️ Efficient Air Circulation – Distributes cold air evenly through refrigerator and freezer 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Simple plug-in wiring connector for quick installation 🛡️ Fixes Common Issues – Solves frost buildup, uneven cooling, or noisy fan problems 📐 Product Specification Part Number: 4681JB1029A Component Type: Refrigerator Evaporator Fan Motor Material: Metal motor housing with balanced plastic fan blade Mounting: Direct-fit replacement in freezer evaporator compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before performing repairs to prevent electrical shock. Steps: Unplug the refrigerator. Remove shelves and freezer rear panel to access the evaporator area. Disconnect the wiring harness and mounting screws on the old fan motor. Install the new XPARTCO 4681JB1029A motor, reconnect wiring, and secure the panel. Restore power and verify quiet, consistent airflow. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore efficient, even cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

WB03X24818CM Range Control Knob Burner Knob. Fits specific GE Gas Range models. Replaces Part Numbers: WB03X24818, AP5989029, PS11729081. Description: This Range Knob is a replacement part for specific GE ranges and oven models. It is used to control the temperature and settings of the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10919249 Range Burner Grate Foot The XPARTCO W10919249 is an aftermarket replacement burner grate foot for Whirlpool ranges, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. This small rubber foot attaches to the underside of the cast iron burner grate — the grid that supports your pots and pans above the burners — providing stability, preventing the grate from scratching the cooktop surface, and cushioning it against the range. Over time, these rubber feet wear down, crack, or tear apart from repeated heat exposure and the friction of grates being lifted and set back down during cleaning. A worn or missing foot typically shows up as a grate that wobbles, sits unevenly, or scratches the cooktop surface underneath. Installation requires adhesive to hold the new foot securely in place. It directly replaces W10919249, 1009149, 4455069, 74007356, 8003P033-60, W10465081, WP74007356, AP6037279, AWP42716, EAP11770098, PD00037900, PS11770098. Quick Answer The XPARTCO W10919249 Range Burner Grate Foot fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges with a wobbling, uneven, or scratching burner grate from cracked, broken, or missing feet. Sold individually. Replaces W10919249, 1009149, 4455069, 74007356, 8003P033-60, W10465081, WP74007356, AP6037279, AWP42716, EAP11770098, PD00037900, PS11770098. Adhesive is required to hold this foot in place — it isn't a simple snap-fit — and if a broken foot's remnant is stuck in the mounting hole, you may need to pick or drill it out first. Common Problems This Part Fixes Burner grate wobbling or sitting unevenly Grate scratching the cooktop surface underneath Cracked, torn, or worn rubber foot Missing foot on one or more grate legs Grate noise or rattling during use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range burner grate foot directly replaces the following OEM and cross-reference part numbers: W10919249, 1009149, 4455069, 74007356, 8003P033-60, W10465081, WP74007356, AP6037279, AWP42716, EAP11770098, PD00037900, PS11770098 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This grate foot is compatible with select Whirlpool ranges, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges built on the Whirlpool platform, including model numbers such as WFG505M0BS, WFG505M0BB1, WFG505M0BB2, WFG320M0BB1, WFG320M0BB2, WFG320M0BS0, WFG320M0BS2, WFG320M0BS3, WFG320M0BW1, WFG320M0BW2, WFG550S0LZ0, WFG550S0LZ1, WFG550S0LW0, WFG550S0LW1, WFG550S0LB0, WFG550S0LB1, WFG550S0LV0, WFG550S0LV1, WGG745S0FE05, WGG745S0FH05, WGG745S0FS05, KFGG500EWH3, KFGG504KPS0, and Amana AGR5715QDB, AGR5715QDQ, AGR5715QDS, AGR5715QDW, AGR5725QDB, AGR5725QDQ, AGR5725QDS, AGR5725QDW. Note: Always verify your full model number before ordering, since Whirlpool uses several different grate foot sizes across its range lineup, including the related W10185266 (4-pack) and 814323 (5-pack) foot kits used on other models. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement burner grate foot — stabilizes the grate and protects the cooktop surface Resolves "wobbling grate," "scratching cooktop," and "cracked or missing foot" symptoms Attaches to the underside of the cast iron burner grate Sold individually Direct drop-in replacement matching the original size and mounting Replaces W10919249, 1009149, 4455069, 74007356, 8003P033-60, W10465081, WP74007356, AP6037279, AWP42716, EAP11770098, PD00037900, PS11770098. Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10919249 OEM Part Number W10919249 Part Type Range Burner Grate Foot Condition Aftermarket Replacement Material Rubber Installation Method Adhesive required (not a snap-fit) Repair Difficulty Easy Quantity 1 grate foot (sold individually) Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Range Should Be Cool And Unplugged Before Starting — Adhesive Is Required Make sure the range is cool and disconnected from power before beginning. Remove the burner grate and turn it over to access the mounting hole for the old foot. If the old foot has broken off and left a torn or stuck remnant in the hole, use the pointed end of a pick or small tool to probe and work the remaining piece free — this can take a bit of patience, and some installations may require carefully drilling out the stuck portion if picking doesn't fully clear it. Clean out the mounting hole once it's clear. Apply adhesive to the new W10919249 foot as needed, since this part is not a simple snap-fit and requires adhesive to hold it securely in place. Press the new foot firmly into the mounting hole and allow the adhesive to cure per its instructions before using the range. Reinstall the grate and confirm it sits level and stable with no wobble. Tools needed: pick or small probing tool, adhesive, possibly a drill for stuck remnants. Frequently Asked Questions My grate wobbles and scratches the cooktop. Is this the part I need? Yes, this is the most common symptom of worn or missing grate feet. Once the rubber foot cracks, wears thin, or falls off, the metal grate leg can sit directly against the cooktop surface, causing wobbling, uneven seating, and scratches. The old foot broke and left a piece stuck in the hole. How do I remove it? One customer used the pointed end of a pick to probe the mounting hole until the torn remnant of the old foot came free. If picking doesn't fully clear it, another customer found they needed to carefully drill out the remaining portion before cleaning the opening and installing the new foot. Does this foot come with adhesive, or do I need to buy that separately? Adhesive is required to hold this foot in place and is not included — you'll need to source a suitable adhesive separately. If the fit feels slightly loose, one customer resolved this by using a hot glue gun to anchor the feet securely. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the size and mounting fit of the original W10919249 burner grate foot used in compatible Whirlpool, Maytag, KitchenAid, and related ranges. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8577274 Dryer Thermistor - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 8577274 Dryer Thermistor. This replacement temperature-sensing resistor is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers, offering a cost-effective alternative to the original. It monitors air temperature changes during the drying cycle, providing feedback to the control board to regulate heat levels, preventing overheating and ensuring efficient drying. This part addresses issues like prolonged or shortened drying times, inaccurate temperature readings, or error codes, often caused by a faulty thermistor. Note: Includes (1) thermistor (mounting hardware not included). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP8577274, 8577274, 1181075, 3390292, 3406294, 3976615, 772546, ER8577274, WP8577274VP, PD00002401, EAP11746740, AP6013514, PS11746740. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: 3LCED9100WQ0, 7MGGW9200MW3, 7MWGD8300SW1, 7MWGD8500SR1, WED6200SW1, WED8000DW3, WED8300SW0, MEDB880BW0 Kenmore: 110.60884990, 110.6007299, 110.6093699, 110.7095299 Maytag: 7MMGDB850WL0, MVWC565FW0 KitchenAid, Amana, Inglis, Crosley: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, and Crosley dryers. Specifications: High-quality thermistor, approximately 11K Ohms at 70°F (21°C), located on blower housing. Reliable Performance: Monitors drum air temperature to prevent overheating and ensure efficient drying. Easy Installation: Requires 1/4-inch nut driver, small flathead screwdriver, and pliers; typically installed in 15–30 minutes. Effective Fixes: Resolves prolonged or shortened drying times, inaccurate temperature readings, or error codes. Product Specification Part Number: XPARTCO 8577274 Component Type: Dryer thermistor Material: Plastic and metal Electrical Specs: Approximately 11K Ohms at 70°F (21°C), varies with temperature Compliance: Prop 65 warning for California. Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

(4 Pack) 74009592CM Burner Control Knob Black plastic burner knob Fits Specific Maytag, Jenn Air, Whirlpool ranges Replaces Part Numbers: WP74009592, 74009592, 1032643, 71003477, AP6011140, PS11744334. Description: This Top Burner Control Knob is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise control over the heat level of the stove's burners, enabling users to adjust the flame size for various cooking needs. Constructed from durable materials, the knob is designed to withstand the rigors of daily use, providing a reliable interface for setting and maintaining the desired cooking temperature. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 279816 Dryer Thermostat Kit The XPARTCO 279816 is an aftermarket replacement thermal fuse and high-limit thermostat combo kit for Whirlpool-built dryers. These are the dryer's two thermal safety devices, and they're bundled together in this kit because they tend to fail around the same time and share a common cause: restricted airflow that lets heat build up beyond safe levels. The high-limit thermostat is the first line of defense, opening at approximately 250°F (L250-80F) to interrupt heating if the dryer runs too hot. If that isn't enough to bring the temperature back down, the thermal fuse is the final failsafe, opening permanently at approximately 309°F to cut power to the dryer entirely. That's an important distinction between the two parts: the high-limit thermostat is a cycling safety device that can open and close as temperature rises and falls, while the thermal fuse is a one-time device — once it blows, it's done, and the dryer won't run again until it's replaced. This kit includes both components plus mounting screws and a wiring set with a jumper wire and extra terminals, which is used specifically when replacing an older-style thermostat that had a wire pressing directly onto the heating element. A dryer that won't start at all, with no lights or response, usually means the thermal fuse has blown; a dryer that runs but won't heat, or that stops heating partway through a cycle, points more toward the thermostat. It directly replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299. Quick Answer The XPARTCO 279816 Dryer Thermostat Kit fixes Whirlpool-built dryers that won't start at all, won't heat, or stop heating partway through a cycle. Includes a thermal fuse (opens ~309°F), a high-limit thermostat (opens ~250°F), mounting screws, and a wiring set. Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, PS334299. Always inspect and clean the dryer venting when replacing this kit — a blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer runs and tumbles but produces no heat Dryer heats for a while, then stops heating partway through a cycle Dryer that stopped working suddenly, especially after running unusually hot Clothes coming out extremely hot right before the dryer stopped heating or stopped entirely Repeated blown fuses or tripped thermostats on a dryer with a known venting restriction Continuity test shows an open circuit across the old fuse or thermostat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299. 3977393 is the thermal fuse component and 3390291 is the "new-style" high-limit thermostat component included in this kit. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED series Maytag electric and gas dryers — NED series (select Whirlpool-built models) Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, and Roper dryers (select models) Kenmore and KitchenAid dryers (select Whirlpool-built models) Verified model numbers include: WED6200SW1, NED4600YQ0, NED4600YQ1, NED4655EW1, and LER3624EQ. Note: The wiring set included in this kit is designed for replacing an older-style thermostat that used a wire pressed directly onto the heating element. If your dryer uses the true old-style push-on thermostat and fuse combination (part 3977767), you'll need a different kit (commonly listed as APN197) instead of this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which kit fits your dryer. Key Features Complete combo kit — thermal fuse, high-limit thermostat, mounting screws, and wiring set in one package Thermal fuse opens at approximately 309°F as a one-time, non-resettable safety cutoff High-limit thermostat opens at approximately 250°F (L250-80F) as a cycling safety device Resolves "won't start at all," "runs but doesn't heat," and "stops heating mid-cycle" symptoms Wiring set includes jumper wire and extra terminals for older-style push-on thermostat connections Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299 Compatible with Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, and KitchenAid dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 279816 OEM Part Number 279816 Part Type Dryer Thermal Fuse & High-Limit Thermostat Kit Condition Aftermarket Replacement Kit Contents Thermal fuse, high-limit thermostat, mounting screws, wiring set Thermal Fuse Opening Temp Approx. 309°F (one-time, non-resettable) High-Limit Thermostat Opening Temp Approx. 250°F / L250-80F (cycling) Wiring Set Jumper wire + extra terminals for older-style push-on thermostats Quantity 1 kit Compatible Brands Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, KitchenAid Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing area where both the thermal fuse and high-limit thermostat are mounted, usually close together near the heating element or blower assembly. Photograph the wiring before disconnecting anything, and note whether your old thermostat used a push-on wire connection at the heating element — if so, use the included jumper wire and extra terminals to make the new connection correctly. Remove the mounting screws holding each old component in place and disconnect their wire terminals. Before installing the new parts, test the old fuse and thermostat with a multimeter to confirm which one (or both) is actually open, rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Install the new thermal fuse and thermostat from this kit in the same mounting positions, reconnect the wire terminals (using the included wiring set if applicable), and secure the mounting screws. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions Why does this kit include two different parts instead of just one? The thermal fuse and high-limit thermostat work together as a two-stage safety system, and they're bundled because they commonly fail together — both are reacting to the same underlying overheating condition, usually restricted airflow. The high-limit thermostat trips first at a lower temperature and can cycle open and closed; if that's not enough to control the heat, the thermal fuse trips at a higher temperature and shuts the dryer down permanently until replaced. Replacing both together addresses the full safety chain rather than just one link in it. My dryer won't start at all versus my dryer runs but doesn't heat — which part is which? A dryer with absolutely no response — no lights, no tumbling, nothing — usually points to the thermal fuse, since it's wired to cut power more broadly when it blows. A dryer that tumbles and runs normally but produces no heat, or that starts heating and then stops partway through, points more toward the high-limit thermostat. Testing both components with a multimeter will confirm exactly which one has failed. I replaced both parts and the dryer failed again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Neither of these parts fails from age; they trip or blow because the dryer overheated. If new parts fail again, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the parts still fail, have the heating element checked as well, since a shorted element can also drive excess heat. Do I need the wiring set included in this kit? Only if your dryer's original thermostat used a wire that pressed directly onto the heating element (an older-style connection) rather than a standard push-on terminal. If your dryer already uses a straightforward terminal connection, you can skip the jumper wire and extra terminals and connect the new thermostat directly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the opening temperatures, terminal configuration, and mounting positions of the original 279816 thermal fuse and high-limit thermostat kit used in compatible Whirlpool, Maytag, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5221ER1003S Washer Water Valve The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve. Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number. Quick Answer The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order. Common Problems This Part Fixes Washer won't fill with cold water at the start of the cycle Cold water fills much more slowly than it used to Washer keeps filling continuously, even while water is simultaneously draining out Water leaking steadily at the cold water connection point Visible rust or mineral buildup around the valve body or connection Cycle stalling at the fill step and never advancing to wash Water pooling underneath or behind the washer near the cold supply line Cold wash or cold rinse cycles specifically affected while other cycles run fine Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as: LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW LG W3600HVA Kenmore WKE100HVA (select LG-built models) Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure Rated 12V with small male spade terminal connections for a secure electrical fit Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L Direct drop-in replacement — mounts underneath the top panel at the original connection point Replaces 4869496, AP6798394, PS12587936, and EAP12587936 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number 5221ER1003S OEM Part Number 5221ER1003S (also 5221ER1003A) Part Type Washer Water Inlet Valve — Cold Condition Aftermarket Replacement Brand LG Application Front-Load Washers Voltage 12V Electrical Connection Small male spade terminals Color Gray Material Plastic and metal Height 4.75 in. Width 3.25 in. Length 2.25 in. Location Underneath the top panel, dispenser and control panel assembly Quantity 1 valve Compatible Brands LG, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves. Frequently Asked Questions My washer keeps filling even while it's draining. Is that this valve? Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis. Cold water won't fill but hot water works fine. Is this the right part? Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace. I see rust on my old valve but it isn't leaking yet. Should I still replace it? It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later. What's the difference between 5221ER1003S and 5221ER1003A? These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1027C Refrigerator Evaporator Fan Motor Replaces Part Numbers: 4681JB1027C, EAU60694512, 4681JB1027V, 4681JK1004E, AH3523323, EA3523323, EAU52096201, EAU60694529, SM1027C, AP4507961, PS3523323.  Replaces LG #4681JB1027C. 13VDC, 3.1 W, .24A. Has quick disconnect. Description: This Fan Motor is a replacement part for specific LG refrigerator models. It is essential for circulating air throughout the refrigerator and freezer compartments, ensuring that the temperature is evenly distributed and maintained at the set levels. This motor powers the fan that helps to cool the evaporator coils and dissipate heat, which is vital for the appliance's cooling efficiency. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPHVC1095 Microwave High Voltage Capacitor, 2100 VAC, 0.95 µF – Universal Microwave Replacement Product Description Restore proper microwave heating performance with the HVC1095 Microwave High Voltage Capacitor (2100 VAC, 0.95 µF). This high-quality aftermarket capacitor stores and releases electrical energy required by the high-voltage circuit to power the magnetron. A faulty capacitor may cause the microwave to stop heating, hum loudly, or trip breakers. Replacing it with this reliable XPHVC1095 capacitor helps restore efficient heating and safe microwave operation. Compatibility This universal microwave high-voltage capacitor is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 2100 VAC, 0.95 µF capacitor. Commonly used in countertop, over-the-range, and built-in microwave models. Always verify voltage and capacitance requirements before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to OEM-equivalent electrical specifications ⚡ 2100 VAC, 0.95 µF Rating – Supports proper magnetron operation 🔥 Restores Heating Function – Fixes microwave running but not heating 💪 Heavy-Duty Construction – Designed for high-voltage applications 💰 Cost-Effective Repair – Reliable alternative to OEM microwave capacitors 📐 Product Specification Part Number: XPHVC1095 Component Type: Microwave High Voltage Capacitor Voltage Rating: 2100 VAC Capacitance: 0.95 µF (microfarad) Application: High-voltage power supply circuit, (4.8 mm) 2 male terminals, Oval Shape Mounting: Bracket-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:WARNING: This high-voltage capacitor is for microwaves. High-voltage capacitor is an electric device that holds a charge of electricity in the high-voltage circuit of the microwave. Because high-voltage capacitors in a microwave can retain a lethal electrical charge even when the microwave is unplugged, a service technician should install this part. Basic Steps: Unplug the microwave. Remove the outer cabinet. Safely discharge the existing capacitor. Disconnect wiring and remove the old capacitor. Install the new HVC1095 capacitor securely. Reconnect wiring, reassemble the cabinet, and restore power. Test microwave heating operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave heating safely and efficiently — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 5220FR2008F Washer Water Valve The XPARTCO 5220FR2008F is an aftermarket replacement water inlet and dispenser valve assembly for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's water source and to the washer's solenoid wiring, controlling exactly how much water enters the tub and ensuring the correct fill level for each cycle. The assembly has 1 inlet and 4 outlets. Rated 120V, 60Hz. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer continuing to fill even after it should be full, filling slowly, overfilling, or leaking water into the drum when the washer is off. On some LG models, this can also trigger an FE error code specifically tied to the fill process. It directly replaces AP4445613, 1268512, 5221ER1002B, AH3527431, EA3527431, and PS3527431. Quick Answer The XPARTCO 5220FR2008F Washer Water Valve fixes LG and select Kenmore front-load washers that keep filling past full, fill slowly, overfill, or leak water into the drum when off — sometimes accompanied by an FE error code. 120V, 60Hz, 1 inlet, 4 outlets. Replaces AP4445613, 1268512, 5221ER1002B, AH3527431, EA3527431, PS3527431. Some LG steam washers use this valve alongside a separate hot water valve — if only one side is failing, you may only need to replace the specific valve at fault rather than the whole group. Common Problems This Part Fixes Washer continues filling with water even after it should be full Washer filling slowly Washer overfilling Water leaking into the drum when the washer is turned off FE error code displayed during the fill portion of the cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 5220FR2008F, 5220FR2008L, 5221ER1002B, AH3527431, EA3527431, AP4445613, ALG51753, EAP3527431, PD00001808, PS3527431 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform, including model numbers such as WM2487HRMA, WM2487HWM, WM2487HWMA, WM2688HNM, WM2688HWMA, WM2455HW, WM2301HW, WM3997HWA, WM3070HRA, WM0532HW, WM2075CW, and WM3987HW. Note: LG uses several visually similar water valves across its washer lineup, including 5220FR2006H and 5221ER1003S. Always confirm your exact part number — comparing your old valve's printed number and photo against the listing is the most reliable way to avoid ordering a similar-looking but incorrect valve. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement water inlet and dispenser valve assembly Resolves "won't stop filling," "fills slowly," "overfills," "leaks when off," and "FE error code" symptoms 1 inlet, 4 outlets Rated 120V, 60Hz Sold individually Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4445613, 1268512, 5221ER1002B, AH3527431, EA3527431, and PS3527431 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP5220FR2008F OEM Part Number 5220FR2008F Part Type Washer Water Inlet & Dispenser Valve Assembly Condition Aftermarket Replacement Application Front-Load Washers Voltage 120V Frequency 60 Hz Inlets / Outlets 1 inlet, 4 outlets Weight Approx. 0.60 lbs Package Dimensions 5.12" x 4.69" x 3.98" Repair Difficulty Easy to Moderate Quantity 1 valve (sold individually) Compatible Brands LG, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access on most LG front-load washers requires removing the top cover to reach the water valve assembly and its electrical connections and hoses. On models with multiple valves (some LG steam washers use one separate hot water valve plus a group of cold water valves), identify specifically which valve is failing before removing anything — check your old valve's printed part number and compare it against a reference photo, since several LG valves look very similar. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and hose from the failing valve, remove its mounting screws, and pull it free. Install the new 5220FR2008F in the same position, reconnect the hose and electrical connector fully, and secure the mounting screws. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking or error codes. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My washer shows an FE error code. Is this the valve I need? Possibly. One customer reported an FE error appearing while the machine was still "filling," which pointed to one of the hot or cold water valves not working correctly. If your FE error consistently appears during the fill portion of the cycle, this valve is a reasonable place to start troubleshooting. My washer has more than one water valve. Do I need to replace all of them? Not necessarily. Some LG steam washers use a separate hot water valve plus a group of valves fed from the cold water main, and it's common for only one specific valve in that group to actually be bad. One customer confirmed this exact setup, testing and replacing only the single failing valve rather than the entire group, which resolved their issue. How do I make sure I'm ordering the correct valve, since several look similar? Check the part number printed directly on your old valve and compare it, along with a photo if available, against the listing before ordering. One customer specifically noted that several LG valves looked alike, and having a clear reference photo was what let them positively identify the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the solenoid design, inlet/outlet configuration, and electrical rating of the original 5220FR2008F valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4 Pack - XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 - Pack Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less