Search results for "leveling"

XPARTCO 8577274 Dryer Thermistor - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 8577274 Dryer Thermistor. This replacement temperature-sensing resistor is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers, offering a cost-effective alternative to the original. It monitors air temperature changes during the drying cycle, providing feedback to the control board to regulate heat levels, preventing overheating and ensuring efficient drying. This part addresses issues like prolonged or shortened drying times, inaccurate temperature readings, or error codes, often caused by a faulty thermistor. Note: Includes (1) thermistor (mounting hardware not included). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP8577274, 8577274, 1181075, 3390292, 3406294, 3976615, 772546, ER8577274, WP8577274VP, PD00002401, EAP11746740, AP6013514, PS11746740. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: 3LCED9100WQ0, 7MGGW9200MW3, 7MWGD8300SW1, 7MWGD8500SR1, WED6200SW1, WED8000DW3, WED8300SW0, MEDB880BW0 Kenmore: 110.60884990, 110.6007299, 110.6093699, 110.7095299 Maytag: 7MMGDB850WL0, MVWC565FW0 KitchenAid, Amana, Inglis, Crosley: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, and Crosley dryers. Specifications: High-quality thermistor, approximately 11K Ohms at 70°F (21°C), located on blower housing. Reliable Performance: Monitors drum air temperature to prevent overheating and ensure efficient drying. Easy Installation: Requires 1/4-inch nut driver, small flathead screwdriver, and pliers; typically installed in 15–30 minutes. Effective Fixes: Resolves prolonged or shortened drying times, inaccurate temperature readings, or error codes. Product Specification Part Number: XPARTCO 8577274 Component Type: Dryer thermistor Material: Plastic and metal Electrical Specs: Approximately 11K Ohms at 70°F (21°C), varies with temperature Compliance: Prop 65 warning for California. Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) Product Overview The XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) is designed to control the heat level of your range’s surface burners. This durable replacement knob restores precise control and a clean, finished look to your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the 7733P410-60 burner knob is likely worn. Replacing it restores proper control of burner heat settings. Replaces Part Numbers Replaces OEM part number: WP7733P410-60, 7733P410-60, 74007733, WP7733P410-60VP, EAP11744702, AWP48511, PD00004326, AP6011505, PS11744702. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, Amana, and other compatible ranges. Whirlpool Ranges Maytag Ranges Amana Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not turning properly Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: 7733P410-60 Part Type: Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Cooktop Control Troubleshooting Guide Knob spins freely → Worn internal insert Cannot adjust flame → Damaged knob Knob falls off → Cracked or loose fit When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or no longer controls burner settings accurately. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off the control shaft and push the new knob firmly into place. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, most knobs are push-on and can be replaced without tools. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

XPARTCO W11220230 Washer Water Inlet Valve The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.. Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors. Quick Answer The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation. Common Problems This Part Fixes Washer not filling with water Slow water fill during cycles Water continuously flowing into washer Incorrect water temperature Washer stopping due to fill errors Leaking or stuck inlet valve Replaces Part Numbers This water inlet valve replaces the following part numbers: W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select washers from the following brands: Whirlpool washers Maytag washers Amana washers Kenmore / Sears washers (select models) Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Three coil hot and cold water valve. OEM-equivalent fit, performance, and durability Restores proper water fill levels and cycle operation Durable construction resists mineral buildup and wear Prevents leaks and overfilling issues Direct replacement for W11220230 valve assembly Product Specifications Part Number W11220230 Part Type three coil hot and cold water inlet valve. Application Top Load / Front Load Washers Condition Aftermarket Replacement Function Controls Water Flow Compatible Brands Whirlpool, Maytag, Amana, Kenmore Installation Notes ⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation. Frequently Asked Questions What does a washer water inlet valve do? It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill. Will this fix a washer that won’t fill? Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice 8557403 Dryer Thermostat  Replaces Part Numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386 Description: This Dryer Thermostat is a replacement part for select Kenmore, Maytag, Whirlpool dryer models. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPMTC-120 Microwave Thermal Cut-Off Fuse 120℃ (248°F) – Normally Closed – Universal Microwave Safety Cutoff Product Description Protect your microwave from overheating with the XPMTC-120 Microwave Thermal Cut-Off Fuse 120℃ (248°F), Normally Closed. This high-quality aftermarket safety device remains closed (conductive) during normal operation and opens permanently when internal temperatures exceed 120℃, cutting power to prevent component damage or fire risk. A tripped thermal cut-off can cause the microwave to lose power or stop heating. Replacing it with the correctly rated NC fuse restores safe operation and proper protection. Replaces Part Numbers XPMTC-120, MTC-120, KSD-120LC, Microwave Thermal Fuse 120C NC, 248F Normally Closed Thermal Cutoff, WB27X1127, 254709, AH239811, EA239811, WB21X0535, WB21X535, PD00023089, EAP239811, AP2026352, PS239811, WB21X10162, 1556022, AH2370041, EA2370041, KSD 120LC, PD00037108, EAP2370041, AP4484224, PS2370041, 5304509474, 5304464093, 4583662, PD00042646, EAP12071309, AP6230621, PS12071309, WB27X11212, 3026293, SE-7350-006, WB24X28948, WB27X10854, PD00044723, EAP8754627, AP5791056, PS8754627, DE47-20059B, 2079767, DE47-20059A, PD00005107, EAP4226453, AP4580112, PS4226453, DE47-20060A, 2079768, PD00036362, EAP4226454, AP4220155, PS4226454, WB27X10567, 946799, AH239709, PD00050529, EA239709, AP3192016, PS239709. Compatibility This normally closed microwave thermal cut-off fuse is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 120℃ (248°F) NC thermal cutoff. Commonly used in countertop, over-the-range, and built-in microwave models. Always verify temperature rating and contact type before ordering.Contact our support team if you’re unsure. 🔍 What’s the Difference Between NC and NO Thermal Cut-Offs? Normally Closed (NC): Circuit is closed during normal operation and opens permanently when the rated temperature is reached.👉 Most microwave thermal cut-offs are NC. Normally Open (NO): Circuit is open during normal operation and closes only when overheated (used in limited designs). ⚠️ Installing the wrong type (NC vs NO) may cause the microwave not to run or fail to protect against overheating. ✅ Key Features 🔄 Aftermarket Replacement – Built to OEM-equivalent safety specifications 🌡️ 120℃ (248°F) Rating – Trips at unsafe temperature levels 🔁 Normally Closed (NC) – Conducts power during normal operation 🛡️ Critical Safety Component – Helps prevent overheating and fire hazards 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut-offs 📐 Product Specification Part Number: XPMTC-120 Component Type: Microwave Thermal Cut-Off Fuse Temperature Rating: 120℃ (248°F) Contact Type: Normally Closed (NC) Function: One-time safety cutoff Material: Heat-resistant metal body Application: Magnetron or microwave cavity temperature protection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:Unplug the microwave before servicing. Microwaves contain high-voltage components—allow capacitors to discharge before handling internal parts. Basic Steps: Disconnect microwave power. Remove the outer cabinet or access panel. Locate the thermal cut-off near the magnetron or cavity. Disconnect wiring and remove the failed fuse. Install the new XPMTC-120 (NC) thermal cut-off in the same position. Reassemble the microwave and restore power. Test operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave safety and dependable operation — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO DD94-01002A Dishwasher Mounting Installation Kit for Samsung. High-quality dishwasher mounting installation kit designed to help secure compatible dishwashers properly during installation. ✓ Dishwasher Installation Part ✓ Replaces DD94-01002A ✓ Compatibility Support Product Description The XPARTCO DD94-01002A Dishwasher Mounting Installation Kit is used to help secure compatible dishwashers during installation. Proper mounting helps keep the dishwasher stable, aligned, and safely positioned under the countertop or cabinet opening. Replacing missing, damaged, or worn mounting hardware can help restore a secure dishwasher installation and prevent unwanted movement during use. Quick Answer If your dishwasher is loose, shifting, not secured under the counter, or missing mounting hardware, the DD94-01002A dishwasher mounting installation kit may be needed. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not secured properly Missing dishwasher mounting hardware Dishwasher shifting during use Loose dishwasher installation Damaged or worn mounting brackets Replaces part Number DD94-01002A, 2077601, AP4450818, ASM941007, PD00007402, EAP4222710, PS4222710. Compatibility This part fits select Samsung and compatible dishwasher models using part number DD94-01002A. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Dishwasher mounting installation kit Helps secure dishwasher in place Supports proper dishwasher alignment Designed for compatible dishwasher models Quality aftermarket replacement part Product Specifications Brand XPARTCO Part Type Dishwasher Mounting Installation Kit Primary Part Number DD94-01002A Compatible Appliance Type Dishwasher Condition New Installation Disconnect power before installation. Follow the dishwasher installation instructions and verify the unit is level, aligned, and securely mounted before use. Troubleshooting Guide ⚠️ Disconnect power before servicing or installing the dishwasher. Check if the dishwasher is level and properly aligned. Inspect mounting brackets and screws for damage or missing hardware. Confirm the dishwasher does not shift when the door is opened or closed. Replace the mounting kit if hardware is missing, damaged, or no longer secure. When Should You Replace This Part? Replace the dishwasher mounting installation kit if the dishwasher is loose, shifting, not properly secured, or if the original mounting hardware is missing or damaged. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout ```

Read more less

XPARTCO W10599356 Washer Water Valve The XPARTCO W10599356 is an aftermarket replacement water inlet valve for Whirlpool-built front-load washers, including full-size and compact models. This valve sits at the back of the washer where the hot and cold water supply hoses connect, and it's the gatekeeper for every drop of water that enters the drum. When the control calls for water, it energizes the valve's solenoid coils to open the hot side, the cold side, or both together, and closes them again once the correct fill level is reached. A valve that won't open leaves you with no fill at all; a valve that won't fully close can let water trickle or flow into the drum even when the cycle isn't calling for it. Over time, mineral deposits and sediment from the water supply can build up inside the valve body and prevent it from sealing fully, the internal solenoid coil can burn out electrically, and the rubber diaphragm or seal inside can simply wear out with age. A failing valve on this platform commonly triggers an F8 E1 or similar fill-related error code, since the control expects water to reach the correct level within a set time and flags it when that doesn't happen. It directly replaces AP5692067, 3023192, PS8689091, and W10509710. Quick Answer The XPARTCO W10599356 Washer Water Valve fixes Whirlpool-built front-load washers that won't fill, fill slowly, overfill, leak water into the drum when the cycle isn't running, or throw an F8 E1 or similar fill-related error code. Solenoid-actuated water inlet valve for the hot and cold supply connections. Replaces AP5692067, 3023192, PS8689091, W10509710. Consider replacing the fill hoses at the same time — they wear on a similar schedule and share the same access point. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum when the washer is off or between cycles F8 E1 or similar fill-related error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash No hot water, no cold water, or neither reaching the drum Water pooling underneath or behind the washer near the supply connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W10599356, W10509710, AP5692067, 3023192, 33090084, C-022/16-B21, EAP8689091, AWP41165, PD00022876, PS8689091 W10509710 was the immediately preceding number that Whirlpool revised to W10599356. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW series (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana front-load washers (select models) Magic Chef, Admiral, and Norge front-load washers (select models) Roper and Kenmore front-load washers (select Whirlpool-built models) Verified model numbers include: WFW70HEBW0, WFW70HEBW1, WFW70HEBW2, WFW72HEDW0, WFW7590FW0, WFW75HEFW0, WFW80HEBC0, WFW80HEBC1, WFW80HEBC2, WFW80HEBW0, WFW80HEBW1, WFW80HEBW2, WFW81HEDW0, MHW3000BG0, MHW3000BG1, MHW3000BG2, MHW3000BW0, MHW3000BW1, MHW3000BW2, MHW3100DW0, MHW4000BW1, MHW4000BW2, MHW4100DW0, MHW5100DC0, MHW5100DW0, NFW5700BW0, NFW5700BW1, NFW5800DW0, 7MWFW72HEDW0, 7MWFW80HEBW0, and 7MWFW81HEDW0. Note: This valve fits Whirlpool's front-load washer platform. It is not intended for top-load washers, which use a different valve design and mounting configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement solenoid-actuated water inlet valve for hot and cold supply connections Resolves "won't fill," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and similar fill-related error codes Direct drop-in replacement for the superseded W10509710 valve Replaces AP5692067, 3023192, PS8689091, and W10509710 Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — typically completed in 30 to 60 minutes Product Specifications Part Number W10599356 OEM Part Number W10599356 (formerly W10509710) Part Type Washer Water Inlet Valve Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool-Built) Actuation Solenoid-operated Connections Hot and cold water supply inlets Supersedes W10509710 Repair Difficulty Easy to Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot and cold water supply lines from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Use a 1/4" nut driver or socket to remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve from inside the cabinet. Photograph the wiring connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove the mounting screw or bracket (often a T-20 Torx screw), and pull the valve free from its mounting position. Install the new W10599356 in the same orientation, secure the mounting screw, and reconnect the electrical connector fully. Reattach the hot and cold water supply lines to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. While everything is accessible, consider replacing the fill hoses as well, since they wear on a similar schedule. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions My washer shows an F8 E1 error. Does that mean the valve is definitely bad? It's a strong indicator, but check the basics first. F8 E1 and similar fill-related codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm both hot and cold supply valves at the wall are fully open, check the inlet screens inside the valve ports for sediment or debris, and make sure the fill hoses aren't kinked. If those check out and the washer still won't fill properly, the inlet valve itself is the likely cause. Water keeps trickling into the drum even when the washer is off. Is that the valve? Yes, this is one of the classic symptoms of a valve that isn't sealing fully closed. Mineral deposits, sediment, or a worn internal diaphragm can prevent the valve from shutting off completely, letting a slow trickle of water continue into the drum between cycles. This can eventually lead to an overfill or water pooling at the front of the washer, so it's worth addressing promptly rather than waiting. Only hot or only cold water isn't coming in. Do I need to replace the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Should I replace the fill hoses while I'm in there? It's a good idea. The fill hoses connect right at the same point you'll already have exposed, wear on a similar timeline as the valve, and are a common source of slow leaks that get blamed on the valve. Since you're already accessing this area, replacing hoses that show any cracking, bulging, or stiffness saves you from repeating the disassembly later. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the solenoid design, flow rate, and mounting configuration of the original W10599356 / W10509710 valve used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X10014 Washer Water Inlet Valve The XPARTCO WH13X10014 is an aftermarket replacement water inlet valve for GE washer/dryer combination units — a single cabinet that houses both wash and dry functions and shares one door, lid, and control system for both. This valve sits at the point where the hot and cold water supply lines connect, and it's the gatekeeper for every drop of water that enters the tub during the wash portion of a cycle. When the control calls for a fill, the valve's solenoid opens to admit water; once the correct level is reached, it closes again. Common causes of failure include mineral or sediment buildup inside the valve body that prevents it from sealing fully, and a burned-out internal solenoid coil. A failing valve on a combo unit produces the same core symptoms you'd see on a standalone washer: the wash side won't fill, fills too slowly, won't stop filling, or leaks after the cycle ends — but because a combo unit shares more components in a single cabinet than separate machines do, it's worth confirming the water issue is isolated to the valve and not connected to other combo-specific parts nearby, such as our WH12X955 lid switch listing, which serves this same GE combo platform. It directly replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040. Quick Answer The XPARTCO WH13X10014 Washer Water Inlet Valve fixes GE washer/dryer combo units that won't fill with water, fill slowly, won't stop filling, or leak after the cycle ends. For GE's combination washer/dryer platform (WSM2420/WSM2480 series). Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, 944040. This valve is specific to GE's washer/dryer combo unit — not a standalone front-load or top-load washer valve. Common Problems This Part Fixes Washer/dryer combo won't fill with water at the start of the wash cycle Water fills much more slowly than normal Unit won't stop filling — water continues past the normal level Water leaking or dripping after the cycle has ended Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Unit not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X10014, WH13X0084, WH13X10013, WH13X84, AP3203931, 944040, AH756629, EA756629, AGE844170, PD00066092, PS756629 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select GE washer/dryer combination units, including model numbers such as: GE WSM2420D0WW, WSM2420D1WW, WSM2420D2WW, WSM2420D3WW, WSM2420D4WW, WSM2420D5WW GE WSM2420D0CC, WSM2420D1CC, WSM2420D2CC GE WSM2420TAAWW, WSM2420TBAWW, WSM2420TCAWW, WSM2420TAAAA, WSM2420TAACC, WSM2420TBAAA GE WSM2420SAZAA, WSM2420SBZAA, WSM2420SBZWW, WSM2420SCZAA, WSM2420SCZWW, WSM2420SDZWW GE WSM2480D0WW, WSM2480D1WW, WSM2480D2WW, WSM2480D3WW GE WSM2480SAZAA, WSM2480SAZWW, WSM2480SBZAA, WSM2480SBZWW, WSM2480SEZAA, WSM2480TCAWW Note: This valve is built specifically for GE's washer/dryer combination units. It is not the same valve used on GE's standalone front-load washers (such as our WH13X10029 listing) and is not interchangeable with them. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combination units Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure Solenoid-actuated design opens and closes precisely on the control's signal Direct drop-in replacement — matches the original mounting and hose connections Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040 Compatible with GE washer/dryer combo units, including WSM2420 and WSM2480 series Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number WH13X10014 OEM Part Number WH13X10014 Part Type Washer Water Inlet Valve Condition Aftermarket Replacement Application GE Washer/Dryer Combination Units Actuation Solenoid-operated Connections Hot and cold water supply inlets Quantity 1 valve Compatible Brand GE Installation Notes ⚠️ Shut Off Water Supply And Unplug Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. On these combination units, the top of the cabinet often lifts off or opens as a single enclosure covering both the wash and dry sections, which also carries the lid switch wiring — note this connector's location before pulling the panel free. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove its mounting screws, and pull it free. Install the new WH13X10014 in the same position, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold water supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet enclosure, reconnecting the lid switch harness if it was disturbed, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the wash side fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions Is this the same valve used on a standalone GE washer? No. This valve is built specifically for GE's washer/dryer combination units, which share a single cabinet and control system for both wash and dry functions. GE's standalone front-load washers use a different valve (such as our WH13X10029 listing), and the two are not interchangeable. Always confirm whether your appliance is a combo unit or a standalone washer before ordering. My unit won't stop filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve. A worn internal seal can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only hot or only cold water isn't coming in. Do I need the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold or serviced as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, connection type, and mounting configuration of the original WH13X10014 valve used in compatible GE washer/dryer combination units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP653 Dryer Idler Pulley and Belt Set Replaces 6602-001655, DC93-00634A The EXP653 is an aftermarket replacement drum belt and idler pulley set for Samsung electric dryers, and also fits select Kenmore, Amana, and Maytag models built on the Samsung platform. These two components work together: the drum belt wraps around the drum and motor pulley to transmit rotation and keep the drum tumbling, while the idler pulley rides against the belt to maintain proper tension so it doesn't slip or sag during operation. Over time, the belt wears, cracks, or glazes over, and the idler pulley's bearing wears out, causing it to spin roughly or seize. Because these two parts work together in the same drive path and tend to wear on a similar timeline, they're commonly sold and replaced as a set. Symptoms of failure include the dryer not starting, the drum not tumbling or spinning, and noise issues such as squealing or grinding during operation. It directly replaces 6602-001655, 6602-001314, 5PH2337, EXP645, PD00002012, EAP2407938, AP4373659, PS4133825 (drum belt), and DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, PD00032419, EAP11771601, AP6038887, and PS11771601 (idler pulley). Quick Answer The EXP653 Dryer Idler Pulley and Belt Set fixes Samsung, Kenmore, Amana, and Maytag electric dryers that won't start, won't tumble or spin, or make squealing/grinding noise during operation. Includes drum belt and idler pulley. Replaces 6602-001655, 6602-001314, 5PH2337, EXP645, PD00002012, EAP2407938, AP4373659, PS4133825, DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, PD00032419, EAP11771601, AP6038887, PS11771601. These two parts wear together — replacing both at once, rather than just the one that failed, helps avoid reopening the dryer again soon after. What's In The Set Component Replaces Function Drum Belt 6602-001655 Wraps around the drum and motor pulley to transmit rotation and keep the drum tumbling. Idler Pulley DC93-00634A Rides against the belt to maintain proper tension so it doesn't slip or sag. Common Problems This Set Fixes Dryer won't start Drum won't tumble or spin Squealing or grinding noise during operation Belt slipping or sagging, causing inconsistent tumbling Vibration or rattling from the belt/pulley area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer idler pulley and belt set directly replaces the following OEM and cross-reference part numbers: 6602-001655, 6602-001314, 5PH2337, PD00002012, EXP645, EAP2407938, AP4373659, ASM874658, PS4133825, DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, EXP645, 4455850, PD00032419, EAP11771601, AP6038887, ASM34631, PS11771601. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This set is compatible with select Samsung electric dryers, and also fits select Kenmore, Amana, and Maytag dryers built on the Samsung platform, including model numbers such as: DV42H5000EW/A3, DV42H5000GW/A3, DV42H5200EF/A3, DV42H5200EP/A3, DV42H5200EW/A3, DV42H5200GF/A3, DV42H5200GP/A3, DV42H5200GW/A3 DV42H5400EF/A3, DV42H5400EW/A3, DV42H5400GF/A3, DV42H5400GW/A3, DV42H5600EP/A3, DV42H5600EW/A3, DV42H5600GP/A3, DV42H5600GW/A3 DV45H6300EG/A3, DV45H6300EW/A3, DV45H6300GG/A3, DV45H7000EW/A2, DV48H7400EW/A2, DV48J7700EW DV45K6200EW/A3, DV45K7600EW/A3, DV40J3000EW/A2, DV48J7770EP, DV50F9A6EVW/A2, DV52J8700EP/A2, DV52J8700EW DV330AEB/XAA, DV331AER/XAA, DV350AEP/XAA, DV350AER/XAA, DV350AEW/XAA DV455EVGSGR/AA, DV455EVGSWR/AA, DV455GVGSGR/AA, DV455GVGSWR/AA DV456ETHDSU/AA, DV456EWHDSU/AA, DV456EWHDWR/AA, DV456GWHDSU/AA, DV456GWHDWR/AA DV457EVGSGR/AA, DV457EVGSWR/AA, DV457GVGSGR/AA, DV457GVGSWR/AA Note: Always verify your full model number before ordering, since Samsung uses different belt lengths and pulley designs across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement set — drum belt and idler pulley in one purchase Resolves "won't start," "won't tumble or spin," and "squealing/grinding noise" symptoms Restores smooth drum rotation with proper belt tracking and tension Reduces noise and vibration from a worn belt or seized pulley Direct drop-in replacement matching the original belt length and pulley mounting Replaces 6602-001655, 6602-001314, 5PH2337, EXP645, PD00002012, EAP2407938, AP4373659, PS4133825, DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, PD00032419, EAP11771601, AP6038887, and PS11771601 Compatible with Samsung, Kenmore, Amana, and Maytag electric dryers Built to OEM-equivalent quality standards Product Specifications Part Number EXP653 Set Contents 1x Drum Belt (replaces 6602-001655), 1x Idler Pulley (replaces DC93-00634A) Condition Aftermarket Replacement Application Samsung Electric Dryers Belt Material Black rubber Pulley Material Metal alloy Repair Difficulty Moderate — front/top panel removal required Compatible Brands Samsung, Kenmore, Amana, Maytag Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Remove the top and front panels of the dryer to access the drum, belt, and idler pulley. Remove the old drum belt from around the drum and motor pulley. Remove the old idler pulley from its mounting bracket. Install the new EXP653 idler pulley in the same position, making sure it spins freely by hand before continuing. Route and install the new drum belt correctly around the drum and motor pulley, matching the original path exactly, and re-tension it through the idler pulley. Reinstall the drum if it was removed, then reassemble the front and top panels. Restore power and run a test cycle to confirm quiet, smooth operation with the drum tumbling normally and no squealing or grinding noise. Tools needed: 1/4" nut driver, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer won't start. Could that really be the belt or pulley? Yes, on some models a broken belt or seized idler pulley can prevent the dryer from starting a cycle at all, since certain safety switches rely on normal drum movement or belt tension to allow the cycle to proceed. If your dryer hums or clicks but won't fully start, or starts and immediately stops, this set is worth checking alongside more obvious suspects like the door switch. Do I need to replace both the belt and the pulley, or just the one that failed? You can replace just the failed component if you've confirmed which one is actually bad, but these two parts share the same drive path and tend to wear out around the same time — a seized pulley can accelerate belt wear, and a worn belt puts extra strain on the pulley. Replacing both together, since you'll already have the dryer open, helps avoid a second teardown soon after. My dryer squeals during operation. Is that this set? Yes, squealing or grinding noise is one of the most common symptoms addressed by this belt and pulley set, typically caused by a worn idler pulley bearing or a belt that's slipping due to lost tension. Is this an OEM or aftermarket part? This is an aftermarket replacement set built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the belt length, rib pattern, and pulley design of the original 6602-001655 belt and DC93-00634A idler pulley used in compatible Samsung, Kenmore, Amana, and Maytag electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 35001092 Dryer Thermostat – Replaces WP35001092 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain proper dryer temperature and consistent drying results with the XPARTCO 35001092 Dryer Thermostat. This High Limit Thermostat is a replacement part for specific dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards. Replaces Part Numbers WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.  Compatibility This replacement dryer thermostat fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature cycling performance 🌡️ Accurate Heat Regulation – Maintains safe, consistent drying temperatures 🔧 Reliable Thermal Control – Helps prevent overheating and heat loss 💰 Cost-Effective Repair – Quality alternative to OEM thermostats 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses 📐 Product Specification Part Number: 35001092 Component Type: Dryer Operating Thermostat Application: Heater or exhaust temperature regulation Material: Heat-resistant metal thermostat housing Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermostat on the heater housing or exhaust duct. Disconnect wiring and remove the old thermostat. Install the new XPARTCO 35001092 thermostat. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 6931EL3002M Dryer Blower Thermostat The XPARTCO 6931EL3002M is an aftermarket replacement dryer blower thermostat, made to replace LG part 6931EL3002M, for select LG and Kenmore dryers. The thermostat is overheat protection on the dryer's blower housing, and it shuts the dryer down if it gets too hot. When it fails, the dryer may stop heating or may not start at all. This is an aftermarket replacement from XPARTCO, not a genuine LG part. It is sold individually. Check your model number before ordering, because LG uses several similar dryer thermostats with different part numbers. Quick Answer The XPARTCO 6931EL3002M Dryer Blower Thermostat replaces the blower thermostat on a compatible LG or Kenmore dryer when it has failed. Replaces 6931EL3002A and 6931EL3002K. Classic symptoms: the dryer won't heat, won't start, or clothes take too long to dry. Common Problems This Part Fixes Dryer not heating Dryer won't start Clothes taking too long to dry or staying damp Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This blower thermostat is made to replace the following LG part numbers: 6931EL3002M, 6931EL3002A, 6931EL3002K, ALG51962, AP5782317, EAP8747887, PD00023476, PS8747887 If your old thermostat shows a different number, contact our support team and we'll check whether it matches. Compatibility This blower thermostat is listed for LG and Kenmore dryers, including these examples: LG DLEX8500V, DLEX8100V, DLEX8000V, DLEX8000W, DLEX9500K, DLEX7700VE LG DLEX2650W, DLEX3370W, DLE3500W, DLG7188WM, DLGX7801VE Kenmore Elite 79681963710, 79681962710 Note: The models above are a sample of several hundred listed by retailers, not a full list. LG dryers also use separate high-limit thermostats with different part numbers, such as 6931EL3003C and 6931EL3003D, which are not the same part. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the LG 6931EL3002M dryer blower thermostat Overheat protection on the dryer's blower housing Cross-references earlier LG part numbers 6931EL3002A and 6931EL3002K Sold individually Product Specifications Part Number XP6931EL3002M OEM Part Number 6931EL3002M Part Type Dryer Blower Thermostat Condition Aftermarket Replacement Quantity 1 Thermostat Application Select LG and Kenmore Dryers Installation Notes ⚠️ Disconnect Power Before Installing Unplug the dryer before you begin and wear work gloves. Remove the panels needed to reach the blower housing for your model, then note which wire goes to which terminal and disconnect them. Remove the old thermostat, install the new one, and reconnect each wire to its original terminal, because a wire on the wrong terminal can damage the thermostat. Refit the panels, restore power, and run a test cycle. Frequently Asked Questions My dryer isn't heating or won't start. Is this the part I need? It can be. Dryers use several thermostats and a thermal fuse, and the same symptoms can come from a clogged vent, the igniter or heating element, or the control board. Check the vent and test the thermostats before replacing this one. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace LG part 6931EL3002M. If you specifically need a genuine LG part, contact our support team. Is this the same as the high-limit thermostat? No. LG sells separate high-limit thermostats, such as 6931EL3003C and 6931EL3003D. Match the part number on your old thermostat before ordering. Will this fit my dryer? It is listed for many LG and Kenmore dryers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688994 Washer Water Inlet Valve (Hot) The XPARTCO W11688994 is an aftermarket replacement hot water inlet valve compatible with select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The hot water inlet valve is mounted at the back of the washer where the hot water supply hose connects. When the washer's control board calls for hot water during a wash cycle, the valve's internal solenoid opens, letting hot water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with hot water at all, fill very slowly with hot water, fail to deliver hot or warm wash temperatures (even when selected), continuously drip water into the tub even when off, or display fill-related error codes. Construction is red and white plastic with a metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688994, W11036928, W11316255, W11486360, and AP7218602. Often replaced as a pair with the cold water inlet valve (W11688995, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688994 Washer Water Inlet Valve (Hot) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers that aren't filling with hot water, fill slowly with hot water, can't reach hot or warm wash temperatures, or have continuous water dripping into the tub when off. Red/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036928, W11316255, W11486360, AP7218602. Often paired with the cold water valve (W11688995, sold separately). Common Problems This Part Fixes Washer not filling with hot water — valve solenoid not opening when commanded Washer filling slowly with hot water — valve partially clogged or weak solenoid No hot or warm water in selected wash temperatures — only cold water flowing in Hot wash cycle running cool — hot valve not delivering normal flow Water continuously dripping into the tub when the washer is off — hot valve stuck open or not fully closing Water leaks at the hot valve body — internal seal failure Wash cycles taking much longer than normal due to slow hot fill Fill-related error codes when hot fill is required by the selected cycle Replaces Part Numbers This hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688994, W11316255, W11036928, W11486360, 4983330, AP7218602, AWP46795, EAP17216729, FIX17216729, OEM21655815, PD00085626, PS17216729.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — 7MWFC9822HC1, 8TWFC6810LW0, WFC682CLW0, WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0-HC3, MHW5630HW0-HW3, MHW6630HC0-HC3, MHW6630HW0-HW3, MHW8630HC0-HC4, MHW8630HW0-HW4 series Amana front-load washers — NFW5800HW0, NFW5800HW1, NFW5800HW2, NFW5800HW3, NFW5800HW4 and related models Inglis front-load washers — IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the hot water inlet valve (typically red). The matching cold water inlet valve is part number W11688995 (typically blue). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of hot water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for hot water and closes the moment the call is dropped 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Red and white plastic body with metal solenoid coil — heat-resistant construction designed for hot water cycle pressure and temperature Replaces W11036928, W11316255, W11486360, AP7218602, and PD00085626 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the cold water inlet valve (W11688995, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688994 Part Type Washer Water Inlet Valve (Hot) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Hot (paired cold valve is W11688995) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Red / White Material Plastic / Metal (heat-resistant) Often Paired With Cold Water Inlet Valve (W11688995, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Important: if the washer has just been running a hot cycle, allow the hot supply hose and valve to cool before handling — hot water can scald. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the hot valve is typically red. Disconnect the hot water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688994 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the hot supply hose at the wall, restore water and power, and run a test cycle on a hot or warm setting to confirm normal hot water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the cold water valve (W11688995) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions My washer isn't filling with hot water — is the hot valve the problem? Likely, yes — that's the most common symptom of a failed hot water inlet valve. Before replacing, do a few quick checks: 1) confirm the hot water supply at the wall is turned on and your home actually has hot water at that connection (test the faucet nearby); 2) check the supply hose for kinks or pinches; 3) inspect the inlet screen on the back of the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean, but the washer still won't get hot water, the W11688994 valve solenoid has likely failed and replacing it will resolve the issue. My washer fills but my hot wash isn't actually hot — could it still be this valve? Yes — when the hot inlet valve is partially failed (opening but not fully, or opening only briefly), the washer may complete its fill cycle by drawing extra cold water to compensate, but the resulting mix is much cooler than the selected wash temperature should be. If you've confirmed your home's hot water is hot, the supply hose is good, and you're still ending up with lukewarm "hot" washes, the hot valve is a likely cause. Replacing it restores proper hot water delivery and accurate wash temperatures. Should I replace the cold water valve at the same time? Yes, it's strongly recommended. The hot and cold inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching cold water valve is part number W11688995 (blue, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — could the hot valve be the cause? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the cold water supply at the wall and check if dripping continues. If it stops, the cold valve is at fault; if it continues, this hot valve is the cause. Replacing the W11688994 will resolve a leaking hot valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688994 hot water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less