Choice Manufactured Parts
Choice 40111201 Dryer Drum Belt Replaces WP40111201
Aftermarket 5-rib / 4-groove dryer drum belt for select Amana, Maytag, Whirlpool-built, Admiral, Crosley, Speed Queen, Magic Chef and related dryers.
Product Overview
The Choice 40111201 Dryer Drum Belt is an aftermarket replacement for Whirlpool/Maytag part WP40111201. The belt wraps around the dryer drum, motor pulley and idler pulley so the motor can rotate the drum during the drying cycle.
A worn, stretched or broken belt can cause the dryer motor to run while the drum does not turn, or may contribute to thumping, slipping or abnormal belt noise.
Quick Answer
Choice part 40111201CM is a 5-rib, 4-groove belt approximately 93.5 inches long designed to replace WP40111201 / 40111201 on compatible Whirlpool-manufactured dryer platforms.
Common Problems This Part May Fix
Dryer runs but drum does not turn
Drum turns intermittently or slips
Broken or visibly cracked belt
Stretched belt with poor tension
Thumping or squealing related to belt wear
Replaces and Cross-References
WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, AP6009126, AWP47792, EAP11742271, PD00002505, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115
Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not a Genuine Whirlpool OEM belt.
Compatibility
Designed for select dryers manufactured under Amana, Maytag, Whirlpool, Admiral, Crosley, Speed Queen, Magic Chef and related brands. Compatible model examples include:
SDE405DAYW
SDE305DAYW
LGA30AW/PLGA30AW
LE4807L/P1163706WL
NG4819L53738
LEA20AL-PLEA20AL
SLG332RAW
LG3412L/P1122505WL
LE2102L/P1118302WL
Important: This is only a partial compatibility list. Verify the full dryer model number and original belt number before ordering. Similar-looking belts can differ in length, width and rib count.
Key Features
Choice Manufactured Parts aftermarket replacement
Replaces WP40111201 / 40111201
5 ribs / 4 grooves
Approx. 93.5-inch belt length
Designed to restore proper drum rotation
Fits many Whirlpool-manufactured dryer platforms
Product Specifications
Choice Part Number
40111201CM
Listing Part Number
40111201
Brand
Choice Manufactured Parts
Part Type
Dryer Drum Drive Belt
Length
Approx. 93.5 in.
Ribs
5
Grooves
4
Material
Reinforced rubber belt
Condition
New
Part Quality
Aftermarket Replacement
Installation Notes
Disconnect electrical power before servicing the dryer.
Access the drum according to the appliance service procedure.
Route the new belt around the drum with the ribbed side against the drum where specified by the dryer design.
Route the belt around the motor pulley and idler/tension pulley exactly as the original belt was installed.
Rotate the drum by hand before reassembly to confirm the belt tracks correctly and is not twisted.
Inspect the idler pulley and drum rollers while the dryer is open; worn support parts can shorten belt life.
Frequently Asked Questions
Is this Genuine Whirlpool OEM?
No. This is a Choice Manufactured Parts aftermarket replacement for WP40111201.
How long is the belt?
Choice specifies this belt at approximately 93.5 inches long with 5 ribs and 4 grooves.
What does the dryer belt do?
It connects the motor drive system to the drum so the drum tumbles while the dryer operates.
Does it replace WP40111201?
Yes. Choice 40111201CM is sold as an aftermarket replacement for WP40111201 and 40111201 on compatible models.
Shop With Confidence
Match the complete appliance model number and original belt number before ordering. Our compatibility team can help confirm fitment.
Choice Replacement5-Rib Belt93.5 in. LengthCompatibility Support
2 Pack - XPARTCO 303373K Dryer Drum Roller Replaces 12001541, WP6-3129480
The XPARTCO 303373K is an aftermarket replacement drum roller support wheel kit for Maytag dryers, and also fits select Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral models. This roller supports the rear of the dryer drum and allows it to spin smoothly against the rear bulkhead throughout the drying cycle, working together with the front drum supports to keep everything rotating evenly.
This kit includes 2 roller, 2 shaft (axle), 2 fiber washer, 2 nut, and 2 C-clip/retainer clip. The roller measures approximately 3" in diameter and 1-1/8" wide, fits a 1/2" shaft, and does not require lubrication. Finished in white or black, made of rubber, plastic, and metal. Over time, the roller's bearing wears out or the wheel develops flat spots from age and use. Symptoms of worn rollers include the dryer being noisy, failing to tumble, leaving marks on clothes, or failing to start. It directly replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, and 312948.
Quick Answer
The XPARTCO 303373K Dryer Drum Roller fixes Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers that are noisy, won't tumble, leave marks on clothes, or won't start. Single roller and shaft, 3" diameter, 1-1/8" wide, fits 1/2" shaft, no lubrication needed. Replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, 312948. For even wear, it's recommended to replace both rear drum rollers at the same time — you'll need two of this kit if your dryer uses two rear rollers.
Common Problems This Kit Fixes
Dryer noisy during operation
Drum won't tumble
Marks left on clothes
Dryer won't start
Squeaking noise during the drying cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum roller kit directly replaces the following OEM and cross-reference part numbers:
12001541, 12001541VP, 3-3373, 303373, 400518, W10116741, DE693, W10116741, Y303373, AH1570070, EA1570070, K35-248, AP4008534, AWP38865, EAP1570070, PD00004911, PS1570070, WP6-3129480, 6-3129480, 1480353, 3-12948, 312948, W10912638, WP6-3129480VP, Y312948, AP6009858, AWP48110, EAP2347258, PD00002609, PS11743031
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum roller kit is compatible with select Maytag dryers, and also fits select Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers built on the Maytag platform, including model numbers such as:
MDE5500AYW, MDE2600AYW, MDE4000AYW, MDE6800AYW, MDE7400AYW, MDE7500AYW, MDE8600AYW, MDE9606AYW
LDE4916ACE, LDE4916ACM, LDE4916ADE, LDE5916ACE, LDE5916ACM, LDE5916ADE
LDE7600ACL, LDE8426GGE, LDE8624ACE, LDE9206ACE, LDE9206ACM, LDE9206ADE, LDE9334ACE, LDE9806GGE, LDE512
LDG4916AAE, LDG4916AAM, LDG5916AAE, LDG5916AAM
LSE7806ACE, MDG9520BWW, DE303, DG7500
Note: Always verify your full model number before ordering, since Maytag uses several different drum roller designs across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drum roller support wheel kit — single roller and shaft
Resolves "noisy," "won't tumble," "marks on clothes," and "won't start" symptoms caused by worn rollers
Kit includes 2 roller, 2 shaft, 2 fiber washer, 2 nut, and 2 C-clip
3" diameter, 1-1/8" wide, fits a 1/2" shaft
Self-lubricating bearing — no lubrication required
White or black finish, rubber/plastic/metal construction
Direct drop-in replacement matching the original mounting
Replaces 12001541, WP6-3129480, 12001541VP, 3-3373, 303373, 400518, AH1570070, DE693, DE693K, EA1570070, K35-248, PS1570070, EAP1570070, W10116741, Y303373, AP4008534, and 312948
Compatible with Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
303373K
OEM Part Number
12001541
Part Type
Dryer Drum Roller Support Wheel Kit
Condition
Aftermarket Replacement
Kit Contents
1x Roller, 1x Shaft, 1x Fiber Washer, 1x Nut, 1x C-Clip
Roller Diameter
3"
Roller Width
1-1/8"
Shaft Fit
1/2"
Lubrication
Not required — self-lubricating bearing
Color
White / Black
Material
Rubber / Plastic / Metal
Repair Difficulty
Easy to Moderate
Quantity
2 drum roller (single kit)
Compatible Brands
Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, Admiral
Installation Notes
⚠️ Unplug Dryer Before Starting — Install The Snap Ring Before Assembling The Roller Onto The Shaft Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the dryer, then remove the drum to access the rear drum roller(s). Remove the old roller by taking off the retainer clip, sliding the roller off its shaft, and removing the shaft itself if it's also being replaced. One customer found it much easier to install the C-clip/snap ring onto the new shaft before assembling the rest of the roller, rather than after. Once assembled this way, you're only dealing with tightening a nut at the back, which can be finger-tightened and then given about a half turn with a 1/2" wrench — useful since one side of the mounting area can be tight to access. Install the new roller, shaft, fiber washer, and nut in the same position, following this assembly order. If your dryer uses two rear rollers and you've ordered a second kit to replace both, repeat this process for the other side. Reinstall the drum, making sure it seats correctly on the new roller(s). While the dryer is fully open, this is also a good opportunity to clean out any accumulated lint from inside the cabinet, since lint buildup here is a genuine fire hazard that isn't addressed by simply cleaning the lint trap. Reassemble the back panel. Restore power and run a test cycle to confirm quiet, smooth tumbling with no marks transferring to clothes. Tools needed: nut driver, 1/2" wrench, work gloves.
Frequently Asked Questions
My dryer squeaks. Is this the part I need?
Yes, squeaking is one of the most common symptoms of worn drum rollers. As the roller's bearing wears down, it can no longer support the drum's rotation smoothly, producing a squeaking or squealing noise that typically gets more noticeable over time.
Should I replace both rollers, or just the one that's obviously worn?
It's recommended to replace both rear drum support rollers at the same time for even wear, even if only one appears visibly worse than the other. This kit includes a single roller and shaft, so if your dryer uses two rear rollers, you'll want to order two of this kit to replace both together.
Do I need to lubricate these rollers?
No, these rollers use a self-lubricating bearing and do not require any additional lubrication during installation or afterward.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag OEM part, but is manufactured to match the diameter, width, and shaft fit of the original 12001541 drum roller kit used in compatible Maytag, Whirlpool, Jenn-Air, Crosley, Kenmore, Amana, and Admiral dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE12X10014 Dryer Drum Belt
The XPARTCO WE12X10014 is an aftermarket replacement drum belt for GE electric and gas dryers, and also fits select Hotpoint, RCA, Kenmore, and Whirlpool models. This is the most common belt used across this dryer platform. This flat belt wraps around the drum, motor pulley, and idler/tensioner pulley, transmitting the motor's rotation to spin the drum and keep clothes tumbling evenly throughout the drying cycle.
Measures 87.875" long, 1/4" wide, flat with 4 ridges on one side. Over time, the belt dries out, cracks, or breaks from age and regular use. If the dryer motor is running but the drum won't rotate, the belt has likely broken. Symptoms of a failing or broken belt include the drum not spinning even though the motor runs, unusual noise during operation, or the dryer not tumbling clothes at all. It directly replaces WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043
Quick Answer
The XPARTCO WE12X10014 Dryer Drum Belt fixes GE, Hotpoint, RCA, Kenmore, and Whirlpool electric and gas dryers where the motor runs but the drum won't rotate, or where you hear unusual noise or no tumbling at all. 87.875" long, 1/4" wide, flat, 4 ridges. Replaces WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043. Clean any dust off the drum with glass cleaner and a paper towel before installing the new belt — soapy cleaners can cause the belt to slip.
Common Problems This Part Fixes
Motor runs but the drum won't turn
Dryer not tumbling clothes at all
Unusual noise during operation
Squealing on startup, possibly indicating a worn belt or bearing
Drum stopping mid-cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select GE electric and gas dryers, and also fits select Hotpoint, RCA, Kenmore, and Whirlpool dryers built on the same platform, including model numbers such as GTD33EASK0WW, GTD42EASJ2WW, GTD42GASJ2WW, and GTD45EASJ2WS.
Note: Always verify your full model number before ordering, since GE uses several different belt lengths across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drum belt — the most common belt used on this GE/Hotpoint dryer platform
Flat belt with 4 ridges for secure grip against the drum, motor, and idler pulleys
Resolves "motor runs but drum won't turn," "unusual noise," and "won't tumble" symptoms
87.875" long, 1/4" wide
Direct drop-in replacement matching the original length and profile
Replaces WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043
Compatible with GE, Hotpoint, RCA, Kenmore, and Whirlpool electric and gas dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPWE12X10014
OEM Part Number
WE12X10014
Part Type
Dryer Drum Belt
Condition
Aftermarket Replacement
Length
4 ribs, 87.875
Width
1/4"
Profile
Flat, 4 ridges on one side
Function
Transmits motor rotation to spin the drum
Repair Difficulty
Easy to Moderate
Quantity
1 drum belt
Compatible Brands
GE, Hotpoint, RCA, Kenmore, Whirlpool
Installation Notes
⚠️ Unplug Dryer Before Starting — Clean Drum Dust With Glass Cleaner, Not Soap Disconnect power at the outlet before beginning. Wear work gloves. Remove the screws on the back panel and pull the dryer away from the wall for access, or access from the front panel depending on your model — look down inside the front panel for two bolts holding the front assembly in place, removable with a 5/16" socket, taking care to disconnect the friction-fit door switch sensor wires as you pull the panel away. Locate the drive belt and tension pulley. Release tension on the idler pulley and remove the old belt from the motor pulley and drum. If the belt was broken, take note of its orientation and routing path before removing any remnants, since figuring out how it wraps around the tensioner is the trickiest part of reinstallation. Dust buildup on the drum can cause the new belt to slip — clean the drum thoroughly with glass cleaner and a paper towel before installing the new belt. Do not use a soapy cleaner, since soap residue will cause the belt to slip. Feed the new WE12X10014 belt around the drum, then through the idler pulley and motor pulley, matching the original routing. Pull the belt tight, re-tension the idler pulley, and rotate the drum by hand with the front cover off to confirm smooth movement before reassembling. Reinstall the front or back panel. Don't forget to reconnect the exhaust vent hose before restoring power, or you may blow lint and dust throughout your laundry room on the first run. Restore power and run a test cycle to confirm smooth, quiet tumbling. Tools needed: 5/16" socket, Phillips screwdriver, adjustable wrench, glass cleaner, paper towels, work gloves.
Frequently Asked Questions
The motor is running but the drum won't turn. Is this the belt?
Yes, this is the classic and most reliable sign of a broken drum belt. If you can hear the motor running normally but the drum itself stays still, there's a good chance the belt has snapped and is no longer connecting the motor's rotation to the drum.
Why does the installation guide mention cleaning the drum with glass cleaner specifically?
Dust that accumulates inside the drum over time can cause a new belt to slip against the drum surface, undermining the repair before it even gets a fair test. Glass cleaner and a paper towel remove this dust effectively. Avoid soapy cleaners, since soap residue left behind has the same slipping effect you're trying to prevent.
Any tips for figuring out how the belt routes around the tensioner?
If your old belt broke rather than simply wearing thin, take a photo of any remaining belt pieces and their position before removing them completely, since this shows you the correct routing path. One customer specifically noted that figuring out how the belt goes around the tensioner in the proper orientation was the trickiest part of the whole repair — a reference photo or a quick look at an installation video for your model helps considerably.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the length, width, and rib pattern of the original WE12X10014 drum belt used in compatible GE, Hotpoint, RCA, Kenmore, and Whirlpool electric and gas dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine GE OEM Dryer Part
GE WE12X10014 Dryer Genuine OEM Drum Belt
87-inch, 4-rib drum drive belt for select GE, Hotpoint, RCA and Kenmore dryers.
Product Overview
The GE WE12X10014 Dryer Genuine OEM Drum Belt connects the dryer motor pulley to the drum so the drum can rotate during the drying cycle.
This genuine GE replacement belt is designed for compatible GE, Hotpoint, RCA, and select Kenmore dryers that use the common 87-inch, 4-rib drive belt.
Quick Answer
WE12X10014 is an approximately 87 inch long × 1/4 inch wide dryer belt with 4 ribs/ridges. It replaces several earlier GE belt numbers including WE12X42 and WE12X82.
Common Problems This Part May Fix
Dryer drum does not turn
Motor runs but drum stays still
Belt is broken, stretched, glazed, or frayed
Squealing or slapping noise from a damaged belt
Dryer will not tumble properly
Replaces and Cross-References
WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043
Cross-reference numbers are provided for identification. This listing is for Genuine GE OEM part WE12X10014.
Compatibility
Fits select GE, Hotpoint, RCA and Kenmore dryers. Compatible model examples include:
DCLR333ET0WW
DBLR333ET0WW
DBLR333GT0WW
NVLR333ET0WB
NVLR333GT0WB
DVLR223ET0WW
DDE7200SBLWW
DDE7500GAL
DLB3400SBLWH
DWLR473ET0WW
NLLR113ET1WO
DDG7688MCL
Important: This is only a partial compatibility list. Verify the complete dryer model number and original belt part number before ordering.
Key Features
Genuine GE OEM replacement part
Approx. 87 inches long
Approx. 1/4 inch wide
4-rib / 4-ridge drive surface
Transfers motor power to dryer drum
Fits many GE-built dryer platforms
Product Specifications
Manufacturer Part Number
WE12X10014
Brand
GE Genuine OEM
Part Type
Dryer Drum Drive Belt
Length
Approx. 87 in.
Width
Approx. 1/4 in.
Ribs / Ridges
4
Condition
New
Part Quality
Genuine OEM
Package Quantity
1 Belt
Installation Notes
Unplug the dryer before service.
Access the drum and release belt tension from the idler pulley.
Remove the old belt and inspect the idler pulley and motor pulley for wear or debris.
Install the new belt with the ribbed side against the drum where specified by the dryer design.
Route the belt around the motor pulley and idler exactly as shown in the appliance service diagram.
Rotate the drum by hand to confirm smooth tracking before reassembly.
Diagnostic tip: A broken belt can result from a seized idler pulley, worn drum bearing/glides, or an obstructed drum. Inspect related components before installing the new belt.
Frequently Asked Questions
How long is WE12X10014?
It is approximately 87 inches long and 1/4 inch wide.
How many ribs does this belt have?
It has 4 ribs/ridges on the drive surface.
Does it replace WE12X42 and WE12X82?
Yes. WE12X10014 is commonly listed as the replacement for those earlier belt numbers.
Is this a Genuine GE OEM belt?
Yes. This listing is for Genuine GE OEM part WE12X10014.
Shop With Confidence
Verify the complete dryer model number before ordering. Our compatibility team can help confirm whether Genuine GE OEM WE12X10014 is correct for your dryer.
Genuine GE OEM87 Inch Belt4-Rib DesignCompatibility Support
W11665769 Dishwasher Sump Pump and Motor
Pump and Motor Assembly
Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975.
Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
279827 Genuine OEM Whirlpool Dryer Drive Motor
The 279827 is a Genuine OEM Whirlpool replacement dryer drive motor with pre-attached pulley, compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers. The drive motor is the component that powers everything that moves in your dryer — it turns the drum belt (which rotates the drum to tumble clothes) and simultaneously drives the blower wheel (which pushes heated air through the drum and out the exhaust vent). When the motor fails, the dryer either won't start, won't tumble, stops mid-cycle, or makes loud humming, buzzing, or grinding noises.
This is a dual-shaft motor: the drive shaft (1-3/4" long) connects to the drum belt via the pre-attached pulley, and the blower shaft (1-3/4" long) drives the blower wheel. The pulley is pre-attached and is not available separately — if your old motor's pulley is worn, this replacement includes a new one. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the 279827 is one of the most widely used dryer motors across the Whirlpool platform, replacing over 70 legacy part numbers spanning decades of production. Key cross-references include W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, 3395652, AP3094245, PS334304, and EAP334304. Includes the motor assembly, two 1/8" insulated female terminals, and instructions. Before replacing the motor, check the thermal fuse (electric dryers) and door switch first — a blown fuse or failed switch produces identical no-start symptoms and is a far cheaper fix. Installs in 45–90 minutes with basic hand tools.
Quick Answer
The 279827 Genuine OEM Whirlpool Dryer Drive Motor fixes Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, and Kenmore dryers that won't start, won't tumble, stop mid-cycle, or make loud humming/buzzing/grinding noises. Dual-shaft drive motor with pre-attached pulley. Shaft lengths: blower 1-3/4", drive 1-3/4". Includes motor assembly + 2 insulated female terminals + instructions. Genuine OEM. Key cross-refs: W10448892, W10396029, W10194250, 8066206, 3395654, AP3094245, PS334304. Before replacing the motor: check the thermal fuse and door switch first — they're far cheaper fixes for no-start symptoms.
Common Problems This Part Fixes
Dryer won't start — motor has failed or seized
Dryer won't tumble — motor not powering the drum belt
Dryer stops mid-cycle — motor overheating or intermittently failing
Loud humming or buzzing when the start button is pressed — motor trying to start but can't
Grinding or squealing noise during operation — worn motor bearings
Motor runs but drum doesn't turn — pulley worn or belt slipping on a worn motor shaft
Dryer runs intermittently — motor cutting out from thermal overload
Burning smell from the motor area — overheating windings or seized bearings
Motor locked up or seized — bearings failed completely
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drive motor directly replaces a large number of OEM and cross-reference part numbers spanning decades of Whirlpool-platform dryer production. Key replacements include:
279827, 3388235, 2019, 2584, 26000299992, 26000695925, 337099, 337100, 3388209, 3388234, 339088, 3391886, 3391887, 3392857, 339627, 339635, 339662, 339672, 340907, 343029, 345437, 348804, 349587, 349808, 3980069, 660199, 660617, 661654, 687499, 687988, 690094, 690870, 694051, 695089, 695925, 697075, 786067, 786090, 8066206, 8066207, 8115, 8528319, 8538262, 8539555, S87-531, W10194250, W10366770, W10396029, W10396032, W10448892, AH334304, AM211, EA334304, K35-099, OEM9282744, AP3094245, AWP39205, EAP334304, PD00002349, PS334304.
This is one of the most extensively cross-referenced parts in the Whirlpool catalog. If your old motor shows a part number not listed here, contact our support team with your dryer model number and we will verify compatibility.
Compatibility
This drive motor is compatible with select dryers from the following brands:
Whirlpool dryers — electric and gas models across many generations (WED, WGD, LER, LGR, LEQ, LGQ series and many more)
Maytag dryers — select Whirlpool-built models (MED, MGD, MEDC, MEDX series)
KitchenAid dryers (select models)
Jenn-Air dryers (select models)
Amana dryers — select models (NED, NGD series)
Magic Chef dryers (select models)
Admiral dryers (select models)
Norge dryers (select models)
Roper dryers (select models)
Estate dryers (select models)
Kenmore / Sears dryers — select Whirlpool-built models (110-series)
Important — Before Replacing the Motor: A dryer that won't start can be caused by several components that are far cheaper and easier to replace than the motor. Before ordering, check the thermal fuse (electric dryers — test for continuity with a multimeter), the door switch (test for continuity when pressed), and the start switch. All three produce identical no-start symptoms. Only replace the motor after ruling out these common causes — a motor replacement is a significant repair, and it's far cheaper to replace a $10 thermal fuse than a $150+ motor. Always verify your dryer model number before ordering.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Dryer drive motor — powers the drum (via belt and pulley) and the blower wheel simultaneously
Dual-shaft design: drive shaft 1-3/4" and blower shaft 1-3/4"
Pre-attached pulley (pulley is not available separately — included with the motor)
Resolves "won't start," "won't tumble," "stops mid-cycle," "humming/buzzing," "grinding," and "burning smell" symptoms when caused by motor failure
Includes motor assembly, two 1/8" insulated female terminals, and instructions
One of the most widely used dryer motors across the Whirlpool platform — replaces 60+ legacy part numbers
Key cross-references: W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, AP3094245, PS334304, EAP334304
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers
Designed for heavy daily use with minimal noise
DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
279827
Part Type
Dryer Drive Motor with Pulley
Condition
Genuine OEM
Application
Dryers — Electric & Gas (Whirlpool platform)
Drive Shaft Length
1-3/4"
Blower Shaft Length
1-3/4"
Pulley
Pre-attached (not sold separately)
Function
Powers drum rotation (via belt/pulley) and blower wheel
Kit Includes
Motor assembly, 2x 1/8" insulated female terminals, instructions
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, Kenmore
Installation Notes
⚠️ Disconnect Power Before Starting — 240V Circuit (Electric) or Gas Line (Gas) — Wear Work Gloves Disconnect power at the breaker before beginning — electric dryers operate on a 240V circuit and there is a serious risk of electrical shock. For gas dryers, also shut off the gas supply at the shutoff valve. Wear work gloves and safety glasses. Pull the dryer away from the wall. Remove the lint screen and the screws beneath it. For most Whirlpool-platform dryers, remove the top panel by releasing the spring clips at the front, then detach the front panel by removing the screws at the top corners. Disconnect the door switch wires and set the front panel aside. Support the drum and slide it forward to access the motor at the bottom rear. Remove the drum belt from the motor pulley and idler pulley. Photograph the motor's wiring connections before disconnecting. Disconnect the electrical connections from the motor. Remove the blower wheel from the old motor's blower shaft — this typically requires a clamp or clip removal (the blower wheel threads off counterclockwise on many models). Remove the motor mounting clip/bracket and lift out the old motor. Install the new 279827 motor in the same position. Transfer the blower wheel onto the new motor's blower shaft and secure it. Reinstall the motor mounting clip/bracket. Reconnect the electrical connections using the included insulated female terminals if needed (match your photos). Re-route the drum belt around the drum, through the idler pulley, and onto the motor pulley. Reassemble the front panel, top panel, and lint screen. Restore power (and gas for gas dryers) and run a test cycle — confirm the drum spins smoothly and heated air flows through the drum. Tools needed: Phillips screwdriver, nut driver, socket/ratchet set, putty knife (for spring clips), needle-nose pliers, work gloves, safety glasses.
Frequently Asked Questions
My dryer won't start — is the motor definitely the problem?
Not necessarily — and this is important because a motor replacement is a significant repair. A dryer that won't start can be caused by several components that are far cheaper and easier to replace. Before ordering the motor, check these first: 1) Thermal fuse (electric dryers) — a blown thermal fuse is the single most common cause of a no-start condition. Test for continuity with a multimeter; if it reads open, replace the fuse (~$10). 2) Door switch — test for continuity when pressed; if it's failed, the dryer won't start as a safety measure. 3) Start switch — if pressing the start button produces no response at all, the start switch itself may have failed. Only replace the motor after ruling these out. Signs that point specifically to the motor: a loud humming or buzzing when you press start (motor trying but can't turn), grinding or squealing from the motor area, or a motor that runs intermittently and cuts out.
Why does the motor hum but the drum doesn't turn?
A humming motor that won't turn is a classic sign of a seized or failing motor — the windings are energized (hence the hum) but the shaft can't rotate because the bearings have failed or the motor is mechanically stuck. This can also be caused by the blower wheel being jammed with lint or debris, preventing the shaft from turning — so before condemning the motor, check the blower wheel for obstructions. If the blower wheel spins freely and the motor still hums without turning, the motor has failed and needs replacement. Note: a humming motor that won't start will eventually trip the thermal fuse as a safety measure, so you may need to replace both the motor and the thermal fuse.
Why are there so many cross-reference part numbers for this motor?
The 279827 is one of the most extensively cross-referenced parts in the Whirlpool catalog because it's been the standard dryer drive motor across the Whirlpool platform for decades — spanning Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, Kenmore, and many other brands that Whirlpool manufactures for. Over the years, the motor has been assigned different part numbers by different brands, distributors, and catalog systems (W10448892, W10396029, 8066206, 3395654, 3398046, etc.), but they all point to the same motor. If your old motor shows ANY of those numbers, the 279827 is the correct replacement.
Does this motor come with the pulley?
Yes — the pulley is pre-attached to the motor and is not available separately. The pulley is what the drum belt rides on, transferring the motor's rotation to the drum. If your old motor's pulley was worn or grooved (a common cause of belt slipping and squealing), the new 279827 includes a fresh pulley. You will need to transfer the blower wheel from your old motor to the new one — the blower wheel is not included.
Should I replace the belt and idler pulley while changing the motor?
It's strongly recommended. When you replace the motor, the dryer is already apart and both the drum belt and idler pulley are right there in your hands. All three components wear from the same friction and heat cycles, and installing a new motor with a worn belt or a seized idler pulley puts unnecessary stress on the new motor from day one. Many technicians replace the belt, idler pulley, and drum support rollers as standard maintenance whenever the dryer is opened for a motor replacement — the combined cost of these parts is modest compared to the labor of disassembling the dryer again later.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same drive motor with pulley installed in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W11266654 Washer Door Boot Outer Clamp
Description: The Outer Door Boot Seal Clamp Washer is a replacement part specific to Whirlpool-brand washing machines. Multiple washers are used behind the outer boot seal clamp to create a uniform, compressed seal around the washer door opening.
Replaces Part Number: W11266654, W10237503, WPW10237503, 4894886, AP6809210, PS12584490, W10818945.
WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag
Product Description
Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use.
Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model.
Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549.
Compatibility:
Compatible with select dryer models, including but not limited to:
Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0
Kenmore: 110.97591420, 110.97591220, 110.97592420
Maytag: YNED4655EW, YIED4671EW
Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0
Crosley: VDEW6511RW0, VED6505GW0
Amana: NED4655EW0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers.
🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration.
💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation.
🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes.
🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues.
Product Specification
Part Number: WPW10420741
Component Type: Dryer push to start switch
Material: Plastic and brass/stainless steel
Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST)
Compliance: UL-listed, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today!
Add to cart now for a reliable fix!
A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor
The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line.
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535.
Quick Answer
The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause.
Common Problems This Part Fixes
Dishwasher won't drain at the end of the cycle
Water pooling at the bottom of the tub after a completed cycle
Grinding or humming noise coming from the pump area
Dishwasher won't start a new cycle because it detects leftover water from the previous one
Dishes not getting properly cleaned due to poor water circulation
Pump running but producing little or no actual drainage
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform.
Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified motor speed and impeller design
Pumps water out of the tub and through the drain hose at the end of each cycle
Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure
Includes pump motor, impeller, and seal
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM
1/4" male terminals for a direct plug-in electrical fit
Direct drop-in replacement — no modification required
Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535
Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
A00126401
Part Type
Dishwasher Drain Pump Motor Assembly
Condition
Genuine OEM
Brand
Frigidaire
Voltage
120V
Frequency
60 Hz
Wattage
35 W
Amperage
0.8 A
Motor Speed
3600 RPM
Terminals
1/4" male
Kit Contents
Pump motor, impeller, seal
Dimensions
Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H
Color
White / Green
Repair Difficulty
Easy to Moderate — under an hour
Quantity
1 drain pump motor assembly
Compatible Brands
Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore
Installation Notes
⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves.
Frequently Asked Questions
My dishwasher won't drain. How do I know if it's actually the pump and not something simpler?
Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix.
I already replaced the pump and it's still not draining. What should I check next?
This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing.
Does this kit include the check valve flapper?
This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 5221ER1003S Washer Water Valve
The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve.
Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number.
Quick Answer
The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order.
Common Problems This Part Fixes
Washer won't fill with cold water at the start of the cycle
Cold water fills much more slowly than it used to
Washer keeps filling continuously, even while water is simultaneously draining out
Water leaking steadily at the cold water connection point
Visible rust or mineral buildup around the valve body or connection
Cycle stalling at the fill step and never advancing to wash
Water pooling underneath or behind the washer near the cold supply line
Cold wash or cold rinse cycles specifically affected while other cycles run fine
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as:
LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW
LG W3600HVA
Kenmore WKE100HVA (select LG-built models)
Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers
Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure
Rated 12V with small male spade terminal connections for a secure electrical fit
Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L
Direct drop-in replacement — mounts underneath the top panel at the original connection point
Replaces 4869496, AP6798394, PS12587936, and EAP12587936
Compatible with LG and select Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair using basic hand tools
Product Specifications
Part Number
5221ER1003S
OEM Part Number
5221ER1003S (also 5221ER1003A)
Part Type
Washer Water Inlet Valve — Cold
Condition
Aftermarket Replacement
Brand
LG
Application
Front-Load Washers
Voltage
12V
Electrical Connection
Small male spade terminals
Color
Gray
Material
Plastic and metal
Height
4.75 in.
Width
3.25 in.
Length
2.25 in.
Location
Underneath the top panel, dispenser and control panel assembly
Quantity
1 valve
Compatible Brands
LG, select Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves.
Frequently Asked Questions
My washer keeps filling even while it's draining. Is that this valve?
Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis.
Cold water won't fill but hot water works fine. Is this the right part?
Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace.
I see rust on my old valve but it isn't leaking yet. Should I still replace it?
It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later.
What's the difference between 5221ER1003S and 5221ER1003A?
These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH08X10024CM Washer Drive Belt
1300J7 Poly-V auto tension belt. 7 Rib.
Fits GE front load washers.
Replaces Part numbers:WH08X10024, 1168664, AH1020114, AP3884128, EA1020114, PS1020114.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W10730972 Washer Drain Pump Replaces WPW10730972
The XPARTCO W10730972 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Inglis, and KitchenAid front-load washers — including the Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus. The drain pump removes water from the washer tub during the drain and spin phases of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error codes F21, F33, or SD, or leak from the pump area.
This complete assembly includes the motor, pump housing, and integrated filter — these components are only available as a complete assembly and are not sold separately. Rated 120V, 60Hz, 78W, 1.2A (CL.F duty class). Assembly dimensions are 8-3/4"L x 7"W x 5-1/4"H in off-white plastic housing. Note: Whirlpool redesigned this pump — the replacement may look different from the original but fits and functions identically. It directly replaces WPW10730972, W10130913, W10130913-B, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, AP6023956, PS11757304, and additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10730972 Washer Drain Pump fixes Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus front-load washers that won't drain, leave standing water, or display error codes F21, F33, or SD. Complete assembly — motor, pump housing, and filter included. 120V/60Hz/78W/1.2A. 8-3/4"L x 7"W x 5-1/4"H. Note: redesigned — may look different from original but fits identically. Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, PS11757304.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error code F21 displayed — long drain fault (washer unable to drain in allotted time)
Error code F33 displayed — pump motor fault
Error code SD displayed — suds detection or drain issue
Washer stopping mid-cycle due to a drain fault
Loud humming or grinding noise during the drain phase
Water leaking from the front lower area of the washer — pump seal failure
Pump motor running but water not being expelled from the tub
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WPW10730972, W10730972, W10130913, 4281917, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, WPW10730972VP, AP6023956, AWP50633, B40-3A01, EAP11757304, PD00025949, PS11757304
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — Duet series (WFW8300, WFW8400, WFW9050, WFW9150, WFW9200, WFW9250, WFW9400, WFW9450, WFW9500, WFW9550, WFW9600, WFW96HEA, WFW97HED, WFW98HEB and related models)
Maytag front-load washers — 2000 series (MHW2000AW, MHW2000BWW and related models)
Maytag front-load washers — 3000 series (MHW3000BW and related models)
Maytag front-load washers — 4000 series (MHW4000BW, MHW4200BW, MHW5100DW, MHW6000AW, MHW6000XW and related models)
Kenmore / Sears front-load washers — HE2 and HE2T Plus series (110.45862400, 110.47532602 and related models)
Amana front-load washers (select models)
Inglis front-load washers (select models)
KitchenAid front-load washers (select models)
Note: Whirlpool redesigned this pump assembly — the replacement may look different from your original pump (larger in size on some versions) but is engineered to fit and function identically in all compatible models. Always verify your model number before ordering. Before replacing the pump, check and clear the coin trap/drain filter — a clogged filter is a common cause of F21/F33 errors that does not require pump replacement.
Key Features
Removes water from the tub during drain and spin cycles — essential for proper washer operation
Complete assembly — motor, pump housing, and integrated filter included; components are not sold separately
Rated 120V, 60Hz, 78W, 1.2A (CL.F) — correct electrical specifications for compatible Whirlpool-family front-load washers
Dimensions: 8-3/4"L x 7"W x 5-1/4"H — off-white plastic housing
Resolves error codes F21 (long drain), F33 (pump motor fault), and SD (suds/drain) on compatible models
Redesigned assembly — may look different from original but fits and functions identically
Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, and over 20 additional cross-references
Compatible with Whirlpool Duet, Maytag 2000/3000/4000 series, Kenmore HE2/HE2T Plus, Amana, Inglis, and KitchenAid
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPW10730972
OEM Part Number
WPW10730972
Part Type
Front-Load Washer Drain Pump and Motor Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers (Duet, Maytag 2000/3000/4000, Kenmore HE2/HE2T Plus)
Voltage
120V AC
Frequency
60 Hz
Wattage
78W
Amperage
1.2A
Duty Class
CL.F
Dimensions
8-3/4"L x 7"W x 5-1/4"H
Color
Off-White
Material
Plastic housing
Includes
Motor, pump housing, and integrated filter — complete assembly
Design Note
Redesigned — may look different from original; fits identically
Error Codes Resolved
F21 (long drain), F33 (pump motor fault), SD (suds/drain)
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Inglis, KitchenAid
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Place towels on the floor — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel of the washer. Remove the screws on the lower kick panel or snap panel to expose the pump access area. Before removing the pump, drain residual water by removing the coin trap/filter cap from the filter housing (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the drain hose clamps and disconnect the hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Transfer the hoses and wiring to the new W10730972 pump, secure the mounting hardware, and reinstall the front panel. Restore power and water, run a drain/spin cycle, and check for leaks. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), pliers, shallow pan, towels, work gloves.
Frequently Asked Questions
What do error codes F21, F33, and SD mean on Whirlpool Duet and Maytag washers?
F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). F33 indicates a pump motor fault — the control board is not detecting the pump motor operating correctly. SD is a suds detection code that can also appear when drain issues prevent the suds from clearing properly. All three codes point toward the drain pump or a drain obstruction. Before replacing the pump, check and clean the coin trap filter — a clogged filter is one of the most common causes of F21 errors and clearing it often resolves the code without needing a new pump.
Should I check the coin trap filter before replacing the pump?
Yes — always check the coin trap filter before replacing the pump. On Whirlpool Duet and Maytag front-load washers, the coin trap filter is located inside the lower front access panel, typically behind a small cap or cover. Removing the cap and clearing lint, coins, and debris from the filter restores drain flow and clears F21/F33 errors in many cases without any part replacement needed. If the filter is clear and the pump still humbles or fails to drain, the pump needs replacement.
Why does the replacement pump look different from the original?
Whirlpool redesigned this drain pump assembly during its production lifecycle — the WPW10730972 replacement is physically larger than some of the older 8540024-series pumps it supersedes. Despite looking different, the redesigned pump uses the same hose and electrical connection points and is a direct fit in all compatible models. The larger housing is an intentional design improvement to increase pumping capacity. If the pump looks bigger than what you removed, this is normal and expected — install it in the same way as the original.
What is the difference between W10730972 and WPW10730972?
These are the same drain pump assembly. WPW10730972 is the updated Whirlpool OEM part number that superseded the original W10730972. The W10130913 and 8540024 are also cross-references for earlier versions of this same pump. This aftermarket replacement is compatible with all of these numbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and performance of the original WPW10730972 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
