Search results for "refrigerator switch"

WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186. The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes. Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil. Common Problems This Part Fixes Dual-element burner won't turn on at all when the knob is turned Outer ring of a dual/bridge element won't activate while the inner coil still works Burner won't turn off — stays hot even with the knob at the off position Burner stuck at one heat level regardless of where the knob is set No ability to adjust temperature — always full blast or always low Intermittent burner operation — works sometimes, not others Knob feels loose, gritty, or doesn't turn smoothly through its range Burner failure that followed a boilover or liquid spill on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers: WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as: GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655) GE JBS series electric ranges GE JS6 and JS7 series electric ranges (including the JS760 series) GE GRS and GRF series electric ranges Hotpoint electric ranges (select GE-built models) Select Kenmore electric ranges built on the GE platform Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS. Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified contact design for dual-element switching Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element Figure-8 style shaft with two female mounting holes matched to the original control panel bracket Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions Rated 240VAC at 15 amps Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts Direct drop-in replacement — mounts to the same control panel bracket and wiring harness Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB24X25013 Part Type Range Surface Burner Infinite Switch (Dual/Bridge Element) Condition Genuine OEM Brand GE Element Type Controlled Dual (bridge) surface element — inner coil + outer ring Terminal Connections 6 Shaft Style Figure-8 Mounting Two female mounting holes Voltage 240VAC Amperage 15A Function Cycles element power to allow continuous (infinite) heat adjustment across both coil zones Quantity 1 switch Compatible Brands GE, Hotpoint, select Kenmore Installation Notes ⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves. Frequently Asked Questions How do I know if my burner uses a dual-element switch like this one? Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation. Only the outer ring of my dual burner doesn't work. Is it the switch or the element? It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement. Can I use a standard single-element infinite switch instead if this one is out of stock? No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model. What does "infinite switch" mean? An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned. A spill got into the control panel and now the burner won't turn off. Is that the switch? Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

V-156-1C25 Micro Limit Switch Contact Type: SPDT 1NO 1NC Actuator Type: 1.1" Long Hinge Roller Lever Rating: 15A 125 250VAC Lever Length: 1.1" Long Hinge Roller Lever Rating: 15A,1/2HP, 125 250VAC; 0.6A,125VDC; 0.3A, 250VDC   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WR55X10942C Refrigerator Control Board The XPARTCO WR55X10942C is an aftermarket replacement main control board for GE, Hotpoint, RCA, and select Kenmore refrigerators. This board is the central processor for the refrigeration system — it regulates temperature, manages the defrost cycle, and controls compressor operation, coordinating everything that keeps both the fresh food and freezer compartments at the correct temperature. Electrical surges and ordinary long-term wear are both common causes of this board failing. Manufacturer part number 200D4850G022. A failing control board produces a wide range of symptoms because so many functions run through it: inconsistent or fluctuating temperatures, a refrigerator that runs too warm or too cold, the refrigerator not starting at all, unusual clicking noises as the board misfires relay signals, or ice that melts and refreezes as the defrost cycle malfunctions. It directly replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, and PS16729744. Quick Answer The XPARTCO WR55X10942C Refrigerator Control Board fixes GE, Hotpoint, RCA, and select Kenmore refrigerators with inconsistent temperatures, a fridge running too warm or too cold, the unit not starting, clicking noises, or ice that melts and refreezes from a malfunctioning defrost cycle. Manufacturer part number 200D4850G022. Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, PS16729744. GE has released many similar-looking control boards across its refrigerator generations — always confirm your exact model number before ordering, since boards that look alike are not always interchangeable. Common Problems This Part Fixes Refrigerator temperatures fluctuating or running inconsistently Refrigerator running too warm or too cold Refrigerator not starting at all Unusual clicking noises from the refrigerator Ice melting and refreezing due to a malfunctioning defrost cycle Refrigerator or freezer section not cooling properly Symptoms that began suddenly, potentially following an electrical surge Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator control board directly replaces the following OEM and cross-reference part numbers: WR55X10942C, WR55X10942, WR55X10942P, WR49X10060, WR55X10065, WR55X10160, WR55X10187, WR55X10328, WR55X10333, WR55X10335, WR55X10336, WR55X10339, WR55X10358, WR55X10366, WR55X10372, WR55X10379, WR55X10381, WR55X10385, WR55X10396, WR55X10413, WR55X10416, WR55X10426, WR55X10427, WR55X10432, WR55X10436, WR55X10456, WR55X10473, WR55X10474, WR55X10523, WR55X10524, WR55X10526, WR55X10529, WR55X10543, WR55X10552, WR55X10554, WR55X10558, WR55X10589, WR55X10597, WR55X10603, WR55X10606, WR55X10614, WR55X10616, WR55X10626, WR55X10656, WR55X10659, WR55X10699, WR55X10712, WR55X10715, WR55X10722, WR55X10942CT, WR55X11036, AP7188100, AGE29813 PD00074367, 200D2259G017, 200D4850G022, 200D4852G018, 200D4852G024, 200D4854G008, 200D4854G013, 200D6221G013, 200D6221G015, 200D6221G016, WKKT 1304-00-70A. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control board is compatible with select GE and Hotpoint refrigerators, and also fits select RCA and Kenmore refrigerators built on the GE platform. Note — many similar-looking boards exist: GE has produced numerous refrigerator main control boards across different generations that can look nearly identical to this one, and not all of them are interchangeable despite the resemblance. Always verify your full refrigerator model number before ordering, rather than matching by appearance alone. Contact our support team with your model number and we will confirm fitment before you order. Key Features Aftermarket replacement main control board — regulates temperature, defrost, and compressor operation Resolves "inconsistent temperatures," "won't start," "clicking noises," and "ice melting and refreezing" symptoms caused by control board failure Includes built-in defrost controls Manufacturer part number 200D4850G022 Direct drop-in replacement for the original board mounting and harness connectors Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, and a wide range of earlier WR55X-prefix board numbers listed above Compatible with GE, Hotpoint, RCA, and select Kenmore refrigerators Aftermarket replacement built to OEM-equivalent quality standards Moderately difficult repair, typically 15 to 45 minutes Product Specifications Part Number WR55X10942C OEM Part Number WR55X10942C (200D4850G022) Part Type Refrigerator Main Control Board Condition Aftermarket Replacement Brand GE Function Regulates temperature, defrost cycle, and compressor operation Repair Difficulty Moderate — 15 to 45 minutes Quantity 1 control board Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Handle The Board By Its Edges Unplug the refrigerator or shut off power at the breaker before beginning to avoid electrical hazards. Wear work gloves. Access is typically through a rear cover panel: remove the screws securing the cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and reconnecting one in the wrong position will cause a malfunction or no-start symptom. Handle the new board by its edges rather than touching the components directly, and avoid working in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Position the replacement WR55X10942C board in the same location, secure it in place, and reconnect all harnesses firmly, matching the original connector locations exactly as photographed. Put the rear cover back on and tighten the screws, then restore power and confirm normal cooling and defrost operation, along with any dispenser or interior lighting behavior your model has. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My refrigerator temperature keeps fluctuating for no clear reason. Is this the control board? It's a strong possibility, especially if you've already ruled out simpler causes like a door seal that isn't sealing properly or a condenser coil that needs cleaning. Since this board regulates both temperature and the defrost cycle together, a failing board can cause the refrigerator to swing between too warm and too cold as it struggles to manage the system correctly. Could a power surge have caused this failure? Yes, this is a documented and common cause of control board failure. Electrical surges, including those from storms or grid fluctuations, can damage the board's circuitry outright, leading to sudden symptom onset. If your refrigerator's issues started abruptly, especially after a storm or power event, this board is a reasonable first suspect. There are so many similar GE control board part numbers. How do I make sure I'm ordering the right one? This is a real and common point of confusion, since GE has released many visually similar boards across different refrigerator generations that are not all interchangeable. The safest approach is to match your refrigerator's full model number against this listing's compatibility rather than relying on how similar a board looks to your old one. If you're at all unsure, send us your model number and we'll confirm fitment before you order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the processor, relay switching, defrost control circuitry, and harness connector configuration of the original WR55X10942C control board used in compatible GE, Hotpoint, RCA, and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA97-15765C Refrigerator Genuine OEM Condenser Fan Motor Replaces Part Numbers: DA97-15765C, DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650. Description: This Refrigerator Condenser Fan Motor Assembly is an essential component designed to maintain optimal cooling performance in select Samsung refrigerator models. This Genuine OEM part ensures reliable operation by efficiently circulating air through the condenser coils, preventing overheating and maintaining consistent temperatures.

Read more less

XPG499 Microwave Door Switch (Normally Closed) The XPG499 is a universal replacement normally closed (NC) door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch's normally closed contact design matches a wide range of microwave door latch mechanisms across GE, Whirlpool, Samsung, LG, Kenmore, and other brands. Rated 16A, 125/250VAC. Over time, this switch's contacts can wear, pit, or fuse together from repeated cycling and the electrical load carried every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or intermittent operation tied to the door latch area. This is the normally closed counterpart to our EXP497 (normally open) and EXP480 (combined NC/NO) listings — always confirm which specific contact configuration your microwave's failed switch uses before ordering. Quick Answer The XPG499 Microwave Door Switch (Normally Closed) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or operate intermittently near the door latch area. 16A, 125/250VAC, normally closed (NC) contact design. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated. Common Problems This Part Fixes Microwave won't start at all, even though the display and buttons respond normally Microwave display and timer work, but the unit won't heat Microwave stops working intermittently, especially around the door latch Clicking or buzzing sound from the door area without the microwave starting Breaker tripping when the door is opened, indicating a switch contact that has fused shut Door that doesn't feel like it's latching securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: WB24X830, AH237422, EA237422, WB24X0800, WB24X0830, WB24X10075, WB24X800, AP2024338, PS237422, WB24X25397, WB24X817, WB24X10112, WB24X0817, AP6037282, PS11766871, 00606695, 1386420, 606695, AH3477007, EA3477007, AP4067354, PS3477007, PS8726632, 5304408937, 5304509459, 5304464098, 4583655, AP6230614, PS12071302, ANE61784L0AG, AP7040623, WB24X10205, WB24X10147, 251201600930, 3025959, AP5790849, PS8754455, W10269458, W10211973, 1550016, 4393598, 8206347, AH2361111, EA2361111, AP4429884, PS2361111, 6600W1K001C, AP4650823, PS3529293, WB24X824, 253814, WB24X0824, AH237416, EA237416, AP2024332, PS237416, 5304456101, 1198245, 75304456101, AH1532505, EA1532505, AP3960662, PS1532505, 6600W1K001R, 1583495, AH3598700, EA3598700, AP5254801, PS3598700, 3405-001033, DE34-20019A, WP3405-001033, 2028596, 3405-000176, AP4044665, PS4131191, WB24X804 253795, WB24X0422, WB24X0804, WB24X422, AH237397, EA237397, AP2024313, PS237397, WB24X10189, 1810588, AH3486597, EA3486597, AP4980349, PS3486597, 3B73361E, 1325767, 3B73361D, 6600W1K003C, 6600W1K004B, AH3522736, EA3522736, AP4629337, PS3522736, 4415A66600, 1206671, 4415A66610, GSM-V1602A2, AP5322919 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands including GE, Whirlpool, Samsung, LG, and Kenmore, wherever the original switch matches this normally closed (NC) contact configuration and electrical rating. Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same normally closed (NC) configuration. This is a different part from our EXP497 (normally open) and EXP480 (combined NC/NO) listings. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs. Key Features Universal replacement microwave door interlock switch — normally closed (NC) contact design Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure Rated 16A, 125/250VAC Suitable for convection, grill, combination, and solo microwave ovens Direct drop-in replacement matching the original mounting and terminal configuration Replaces a wide range of OEM part numbers across GE, Whirlpool, Samsung, LG, and Kenmore platforms — see full list above Built to OEM-equivalent quality standards Product Specifications Part Number XPG499 Part Type Microwave Door Interlock Switch (Normally Closed) Condition New — Universal Replacement Part Contact Configuration Normally Closed (NC) Max. Current 16A Max. Voltage 125/250VAC Terminal Size 4.7mm Application Convection, Grill, Combination, and Solo Microwave Ovens Related Parts EXP497 (normally open) Quantity 1 door interlock switch Installation Notes ⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead. ⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new XPG499 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My microwave stopped working. How do I know if it's actually a door switch and not something else? A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom. Is it safe to just disconnect a faulty interlock switch so the microwave will run? No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it. How is this different from your EXP497 and EXP480 listings? These are different contact configurations for different switch positions in a microwave's door interlock system. This XPG499 is normally closed (NC) only. Our EXP497 listing is normally open (NO) only, and our EXP480 listing combines both NC and NO contacts in a single switch body. Since most microwaves use two or three interlock switches with different configurations, check which contact type your specific failed switch uses before ordering. My microwave trips the breaker whenever I open the door. What does that mean? This can indicate that one of the door switches has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10404050 Genuine OEM Washer Lid Switch Assembly The W10404050 is a Genuine OEM replacement lid switch and latch assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge top-load washers. The lid switch is a critical safety component that detects when the washer lid is opened or closed. It sends a signal to the control board to allow the washer to fill, agitate, and spin when the lid is closed — and to immediately stop the spin cycle when the lid is opened, preventing contact with a moving drum. This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It features a 4-wire plug connection and includes two bezels (one white and one gray) to match different model color schemes. It directly replaces W10238287, W10744659, W10404050VP, AP5263307, and several additional cross-reference numbers. The companion lid strike (W10240513) is sold separately — inspect the strike on your lid for wear or damage and replace if needed. Installs in 20–30 minutes with basic hand tools. Quick Answer The W10404050 Genuine OEM Washer Lid Switch Assembly fixes top-load washers that won't start, won't spin, have a blinking lid lock light, or continue spinning with the lid open. 4-wire plug connection. Includes white and gray bezels. Replaces W10238287, W10744659, AP5263307, and more. Compatible with Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge washers. Lid strike W10240513 sold separately. Common Problems This Part Fixes Washer will not start — lid lock light blinks without locking Washer fills but will not agitate or spin Washer lid lock light continuously blinks and clicks without engaging Washer continues to spin with the lid open — safety mechanism not working Lid appears locked but washer will not proceed past sensing or fill cycle Washer stops mid-cycle and will not restart without opening and re-closing the lid Lid lock assembly visibly broken or latch no longer springs back after pressing Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10404050, 1938607, W10238287, W10404050VP, W10744659, EAP3497627, AWP41256, PD00003596, AH3497627, AP5263307, EA3497627, PS3497627. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands: Whirlpool top-load washers — Cabrio and WTW series (electronic top-load models) Maytag top-load washers — Centennial, Bravos X, and MVWC/MVWX series Kenmore / Sears top-load washers — 110 series and select others (Whirlpool-built) Amana top-load washers — NTW and ATW series KitchenAid top-load washers Roper top-load washers Admiral top-load washers — ATW series Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Norge top-load washers Note: The W10404050 is for electronic top-load washers with a 4-wire lid lock (Cabrio, Centennial, Bravos, and similar platforms). Older mechanical top-load washers use a different lid switch style. Verify your model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Critical safety component — stops the spin cycle when the lid is opened to prevent contact with a moving drum Signals the control board to allow filling, agitating, and spinning when the lid is properly closed and locked 4-wire plug connection — direct plug-in replacement on compatible models Includes two bezels (white and gray) to match different model color schemes Replaces W10238287, W10744659, W10404050VP, AP5263307, and more Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos X, Kenmore 110 series, and many more Lid strike W10240513 sold separately — inspect and replace if worn Product Specifications Part Number W10404050 Part Type Washer Lid Switch and Latch Assembly Condition Genuine OEM Application Electronic Top-Load Washers (4-wire lid lock) Connector 4-wire plug Color White (includes both white and gray bezels) Includes Lid switch assembly, white bezel, gray bezel Companion Part W10240513 Lid Strike (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. The lid switch assembly is mounted under the washer's top panel near the lid opening. To access it, insert a putty knife about 2 inches from each front corner of the top panel to release the spring clips and lift the top panel. Disconnect the 4-wire harness from the old lid switch assembly. Remove the mounting screws securing the assembly and lift it out. Install the new W10404050 assembly, secure with the mounting screws, and reconnect the 4-wire harness. Choose the appropriate bezel (white or gray) for your model and snap it into place. Lower the top panel until the clips engage. Restore power and run a test cycle to confirm the lid locks, the washer starts, and the spin cycle stops when the lid is opened. Tip: While the top panel is raised, inspect the lid strike (W10240513) on the lid for cracks or wear — if worn, replace it at the same time. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the washer lid switch do? The lid switch assembly serves two functions. First, it is a safety device — when the lid is opened during the spin cycle, the switch immediately cuts power to the spin motor to prevent contact with the moving drum. Second, it signals the control board that the lid is securely closed and locked, allowing the washer to proceed through the fill, agitate, and spin cycles. If the switch fails, the washer either won't start at all, or will fail to proceed past a specific cycle stage because the board cannot confirm the lid is closed. My lid lock light is blinking — does that mean the lid switch needs to be replaced? A blinking lid lock light is one of the most common symptoms of a failed W10404050 lid switch assembly. It typically means the lid lock mechanism is attempting to engage but failing — either because the switch is internally faulty or because the lid strike (W10240513) on the lid is broken and not triggering the switch properly. Inspect the lid strike first — if it is cracked or missing, replace it. If the strike looks intact and the lid lock still blinks without engaging, replace the W10404050 switch assembly. Should I also replace the lid strike (W10240513) at the same time? It depends on the condition of the strike. Open the lid and inspect the two plastic prongs on the underside of the lid that engage the W10404050 latch — this is the W10240513 lid strike. If the prongs are cracked, broken, or noticeably worn down, replace the strike at the same time as the switch assembly. Since the top panel is already lifted for the switch replacement, it is a good opportunity to inspect and replace the strike if needed, using only a Phillips screwdriver. What washers is the W10404050 compatible with? The W10404050 is used on Whirlpool Cabrio and WTW series electronic top-load washers, Maytag Centennial and Bravos X top-load washers, and Kenmore 110 series top-load washers, among others. It is specifically for electronic top-load models with a 4-wire lid lock — not for older mechanical top-load washers that use a simpler 2- or 3-wire lid switch. Verify your model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid switch and latch assembly installed in compatible washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR30X39470 Refrigerator Genuine Ice Maker Fits specific GE refrigerator models. Replaces Part Numbers: WR30X39470, AP7192967, OEM28771870, PS16729732. Description: This Refrigerator Ice Maker Assembly is essential for restoring your refrigerator's ice production capabilities. This Genuine OEM part ensures seamless compatibility with a wide range of GE refrigerator models, providing reliable and consistent ice making. Crafted with high-quality materials, the Ice Maker Assembly delivers efficient performance, helping you maintain a steady supply of ice for your daily needs. Its sturdy design ensures long-lasting durability, reducing the need for frequent replacements. Installing this part is straightforward, allowing you to quickly get your refrigerator back to full functionality without hassle. Whether your original ice maker is malfunctioning, leaking, or has worn out over time, the Refrigerator Ice Maker Assembly offers a perfect replacement solution.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WR55X11132 Refrigerator LED Light Product Overview The XPARTCO WR55X11132 Refrigerator LED Light provides bright, energy-efficient illumination inside your refrigerator, improving visibility and enhancing overall appliance functionality. This high-quality LED module restores clear lighting for easy food access. Note: This is LED Light only, Cover is not included. Quick Answer If your refrigerator light is dim, flickering, or not turning on, the WR55X11132 LED light module may be faulty. Replacing it restores proper interior lighting and visibility. Replaces Part Numbers Replaces OEM part number: WR55X11132, EAP4704284, AGE28811, PD00030062, AP5646375, 3033142, PS4704284. Compatibility This refrigerator LED light is compatible with select GE, Hotpoint, and GE Profile refrigerators. . GE Refrigerators: GFE26GGHBBB, GFE26GGHBWW, GFE26GGHCBB, GFE26GGHCWW, GFE26GGHDBB, GFE26GGHDWW, GFE26GGHEBB, GFE26GGHEWW, GFE26GGHFBB, GFE26GGHFWW, GFE26GGHGBB, GFE26GGHGWW, GFE26GGKBBB, GFE26GGKBWW, GFE26GMHBES, GFE26GMHCES, GFE26GMHDES, GFE26GMHEES, GFE26GMHGES, GFE26GMKBES, GFE26GSHBSS, GFE26GSHCSS. Always verify your appliance model number before ordering. Common Problems This Part Fixes Refrigerator light not working Dim or flickering LED light Poor visibility inside fridge Key Features Bright LED illumination Energy-efficient lighting Long-lasting performance High-quality aftermarket replacement Product Specifications Part Number: XPWR55X11132 Part Type: Refrigerator LED Light Module Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Refrigerator Interior Lighting Troubleshooting Guide No interior light → Failed LED module Flickering light → Failing LED board Dim lighting → Aging LED unit When Should You Replace This Light? Replace this LED light if your refrigerator interior lighting is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Remove the light cover, disconnect the module, and install the new LED light securely. Related Parts Refrigerator Door Switch Control Board Light Cover Frequently Asked Questions Will this light fit my refrigerator?This LED module fits many GE and compatible models. Always verify your model number. Is this LED or bulb type?This is an LED light module, not a traditional bulb. What are signs of a bad LED module?No light, flickering, or dim lighting indicate replacement is needed. Is installation difficult?Most modules are easy to replace, but follow your appliance manual for best results. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO 242278801 Refrigerator Temperature Sensor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling accurately with the XPARTCO 242278801 Refrigerator Temperature Sensor. This high-quality replacement monitors the temperature inside the fresh-food and freezer compartments, sending signals to the control board to regulate cooling. A faulty sensor can cause temperature fluctuations, over-freezing, or warm spots. Replacing it with this reliable XPARTCO part ensures consistent temperature control and energy-efficient performance. Replaces Part Numbers 242278801 PD00029820, EAP8760187, AP5802148, 3016441, PS8760187. Compatibility This replacement temperature sensor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFHS2611LBNA, Electrolux E23BC78IPS3, and Kenmore 253.7041341C. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Accurate Cooling Control – Monitors refrigerator temperature for consistent performance 💰 Cost-Effective Fix – Reliable alternative to expensive OEM parts 🛠️ Simple Installation – Plug-in design for fast, easy replacement 🛡️ Fixes Common Issues – Solves warm refrigerator, freezing, or inconsistent cooling problems 📐 Product Specification Part Number: 242278801 Component Type: Refrigerator Temperature Sensor (Thermistor) Material: Plastic housing with thermistor probe and wiring harness Resistance Range: Approximately 2.7 kΩ at 77°F (varies by temperature) Mounting: Direct-fit installation in refrigerator liner or evaporator area Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, wire clip removal tool ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the old temperature sensor, usually near the evaporator or rear wall. Disconnect the sensor’s wiring harness and remove clips. Install the new XPARTCO 242278801 sensor in the same position. Reconnect wiring, reassemble interior parts, and restore power. Allow several hours for the refrigerator to stabilize temperature. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cooling efficiently — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

DA32-10105RCM Refrigerator Temperature Sensor  Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. 1" probe, 25.75" lead with two pin connectors. Fits Specific Samsung Refrigerator Models. This Defrost Sensor is a replacement part designed specific Samsung refrigerator models. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO DA32-10104N Refrigerator Temperature Sensor The XPARTCO DA32-10104N is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. This sensor is mounted on or near the evaporator coil and continuously monitors the internal temperature of the refrigerator compartment, transmitting real-time readings to the electronic control board. Based on the data received from the sensor, the control board regulates the compressor, evaporator fan motor, and defrost system to maintain the set temperature. When this sensor fails or drifts out of calibration, the control board receives inaccurate temperature readings — leading to a refrigerator that runs too cold, too warm, or triggers a 5E/SE error code. Features a 9-inch cord for easy installation and a sensitive thermal element with temperature detection accuracy of ±0.1°C. Quick Answer The XPARTCO DA32-10104N Refrigerator Temperature Sensor fixes refrigerators that are too warm, too cold, display a 5E/SE error code, or have inconsistent temperatures that spoil food. It monitors internal refrigerator temperature and sends data to the control board to regulate cooling. Compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Common Problems This Part Fixes Refrigerator running too warm — food spoiling faster than normal Refrigerator running too cold — food or drinks freezing in the fresh food section 5E or SE error code displayed on the control panel Inconsistent or fluctuating temperatures inside the refrigerator Compressor running continuously without reaching set temperature Excessive frost or ice buildup on evaporator coils Replaces Part Numbers This sensor directly replaces the following OEM and cross-reference part numbers: DA32-10104N, DA32-10104V, 2030330, ASM1216617, PD00026468, EAP4138666, AP4979323, PS4138666. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung side-by-side refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Monitors internal refrigerator temperature and sends real-time data to the electronic control board Fixes 5E/SE error codes caused by a faulty or out-of-calibration temperature sensor Temperature detection accuracy of ±0.1°C for precise cooling control 9-inch cord length for easy installation and connection to the control board Aftermarket replacement built to OEM-equivalent quality standards Direct drop-in replacement — no modification required DIY-friendly repair — installs with basic hand tools in 30–45 minutes Product Specifications Part Number DA32-10104N Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Refrigerator Temperature Control System Cord Length 9 inches Detection Accuracy ±0.1°C Resistance at 70°F ~9.3K ohms Resistance at 90°F ~7.7K ohms Resistance at 100°F ~6.2K ohms Resistance at 120°F ~4.3K ohms Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. The DA32-10104N sensor is located near the evaporator coil, typically behind the rear panel inside the refrigerator or freezer compartment. Remove the panel, locate the sensor along the yellow wire, disconnect the old sensor from its plug, and connect the new sensor in the same position. Reassemble the panel and restore power. Allow 24 hours for the refrigerator to return to normal operating temperature. Tip: Before replacing, test the old sensor with a multimeter — resistance readings outside the values in the specs table above confirm a faulty sensor. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA32-10104N fit my Samsung refrigerator? This sensor is compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does the temperature sensor do? The temperature sensor (thermistor) continuously monitors the internal temperature of the refrigerator and sends readings to the electronic control board. The control board uses this data to regulate the compressor, fans, and defrost system to maintain the set temperature. When the sensor fails or drifts out of range, the control board receives inaccurate data and cannot maintain proper cooling. What are signs that my temperature sensor needs replacement? Common signs include: the refrigerator running too warm or too cold, food spoiling faster than normal, a 5E or SE error code on the display, inconsistent temperatures, or the compressor running continuously without reaching the set temperature. How do I test the DA32-10104N sensor before replacing it? Use a multimeter to measure the resistance across the sensor terminals. At 70°F the reading should be approximately 9.3K ohms, at 90°F approximately 7.7K ohms, at 100°F approximately 6.2K ohms, and at 120°F approximately 4.3K ohms. Readings significantly outside these values indicate a faulty sensor that needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, accurate temperature sensing at a more affordable price point. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA32-10104N Refrigerator Temperature Sensor The XPARTCO DA32-10104N is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. This sensor is mounted on or near the evaporator coil and continuously monitors the internal temperature of the refrigerator compartment, transmitting real-time readings to the electronic control board. Based on the data received from the sensor, the control board regulates the compressor, evaporator fan motor, and defrost system to maintain the set temperature. When this sensor fails or drifts out of calibration, the control board receives inaccurate temperature readings — leading to a refrigerator that runs too cold, too warm, or triggers a 5E/SE error code. Features a 9-inch cord for easy installation and a sensitive thermal element with temperature detection accuracy of ±0.1°C. Quick Answer The XPARTCO DA32-10104N Refrigerator Temperature Sensor fixes refrigerators that are too warm, too cold, display a 5E/SE error code, or have inconsistent temperatures that spoil food. It monitors internal refrigerator temperature and sends data to the control board to regulate cooling. Compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Common Problems This Part Fixes Refrigerator running too warm — food spoiling faster than normal Refrigerator running too cold — food or drinks freezing in the fresh food section 5E or SE error code displayed on the control panel Inconsistent or fluctuating temperatures inside the refrigerator Compressor running continuously without reaching set temperature Excessive frost or ice buildup on evaporator coils Replaces Part Numbers This sensor directly replaces the following OEM and cross-reference part numbers: DA32-10104N, DA32-10104V, 2030330, ASM1216617, PD00026468, EAP4138666, AP4979323, PS4138666. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung side-by-side refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Monitors internal refrigerator temperature and sends real-time data to the electronic control board Fixes 5E/SE error codes caused by a faulty or out-of-calibration temperature sensor Temperature detection accuracy of ±0.1°C for precise cooling control 9-inch cord length for easy installation and connection to the control board Aftermarket replacement built to OEM-equivalent quality standards Direct drop-in replacement — no modification required DIY-friendly repair — installs with basic hand tools in 30–45 minutes Product Specifications Part Number DA32-10104N Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Refrigerator Temperature Control System Cord Length 9 inches Detection Accuracy ±0.1°C Resistance at 70°F ~9.3K ohms Resistance at 90°F ~7.7K ohms Resistance at 100°F ~6.2K ohms Resistance at 120°F ~4.3K ohms Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. The DA32-10104N sensor is located near the evaporator coil, typically behind the rear panel inside the refrigerator or freezer compartment. Remove the panel, locate the sensor along the yellow wire, disconnect the old sensor from its plug, and connect the new sensor in the same position. Reassemble the panel and restore power. Allow 24 hours for the refrigerator to return to normal operating temperature. Tip: Before replacing, test the old sensor with a multimeter — resistance readings outside the values in the specs table above confirm a faulty sensor. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA32-10104N fit my Samsung refrigerator? This sensor is compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does the temperature sensor do? The temperature sensor (thermistor) continuously monitors the internal temperature of the refrigerator and sends readings to the electronic control board. The control board uses this data to regulate the compressor, fans, and defrost system to maintain the set temperature. When the sensor fails or drifts out of range, the control board receives inaccurate data and cannot maintain proper cooling. What are signs that my temperature sensor needs replacement? Common signs include: the refrigerator running too warm or too cold, food spoiling faster than normal, a 5E or SE error code on the display, inconsistent temperatures, or the compressor running continuously without reaching the set temperature. How do I test the DA32-10104N sensor before replacing it? Use a multimeter to measure the resistance across the sensor terminals. At 70°F the reading should be approximately 9.3K ohms, at 90°F approximately 7.7K ohms, at 100°F approximately 6.2K ohms, and at 120°F approximately 4.3K ohms. Readings significantly outside these values indicate a faulty sensor that needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, accurate temperature sensing at a more affordable price point. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less