Search results for "refrigerator switch"

5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly The 5304524953 is a Genuine OEM Frigidaire/Electrolux replacement defrost heater assembly compatible with select Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers — including the popular Frigidaire Professional 19 cu. ft. single-door models in the FPRU19F8 and FPFU19F8 series. The defrost heater is mounted near the evaporator coils and periodically activates during the dishwasher's defrost cycle to melt frost buildup that accumulates on the coils. Without functioning defrost, frost continues to build up on the evaporator until it blocks airflow — causing the refrigerator or freezer to lose cooling efficiency, run continuously, and ultimately fail to maintain set temperatures. As a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications, the 5304524953 directly replaces 5304523833, AP6997296, PS16227227, and 4975045. Tip: when replacing the defrost heater, it's a good time to also inspect or replace the paired defrost thermostat and defrost timer/control board — these three components form the defrost system and often fail in sequence. Addressing them together saves a future repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The 5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly fixes Frigidaire and related-brand refrigerators and upright freezers with excessive frost or ice buildup on the evaporator coils, freezer or fresh food section too warm, refrigerator running continuously, or food spoiling faster than normal. Genuine OEM. Replaces 5304523833, AP6997296, PS16227227, 4975045. Compatible with Frigidaire Professional FPRU19F8WF0/WF2/WF3/WF4/WF5 and FPFU19F8WF2/WF4/WF5 series, plus Crosley, Electrolux, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built models. Often paired with defrost thermostat replacement. Common Problems This Part Fixes Excessive frost or ice buildup on the evaporator coils Freezer section too warm — evaporator coils iced over and blocking airflow Refrigerator section too warm — cold air not circulating because coils are frosted Refrigerator/freezer running continuously without reaching set temperature Food spoiling faster than normal due to inadequate cooling Visible ice sheet on the rear interior wall of the freezer compartment Defrost heater visibly burned through, broken, or showing arcing damage Multimeter continuity test on the heater shows an open circuit (no continuity) Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: 5304524953, 5304523833, 140223390018, 4975045, AFR19119, AP6997296, EAP16227227, PD00083605, PS16227227. 5304524953 is the current production part superseding 5304523833. Contact our support team with your model number if you need confirmation before ordering. Compatibility This defrost heater assembly is compatible with select refrigerators and upright freezers from the following brands: Frigidaire Professional refrigerators — FPRU19F8WF0, FPRU19F8WF2, FPRU19F8WF3, FPRU19F8WF4, FPRU19F8WF5 series (19 cu. ft. single-door) Frigidaire Professional upright freezers — FPFU19F8WF2, FPFU19F8WF4, FPFU19F8WF5 series Frigidaire refrigerators — FPRU19F7WF0 and related FPRU/FPFU series models Electrolux refrigerators and freezers — select Frigidaire-platform models Crosley refrigerators (select Frigidaire-built models) Gibson refrigerators (select models) Kelvinator refrigerators (select models) Tappan refrigerators (select models) Westinghouse refrigerators (select models) Kenmore / Sears refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance Defrost heater assembly — periodically melts frost buildup on the evaporator coils to maintain proper airflow and cooling efficiency Direct factory-original replacement — no modifications required Current production part — directly supersedes 5304523833 Replaces AP6997296, PS16227227, and 4975045 (plus 5304523833) Compatible with Frigidaire Professional FPRU19F8 and FPFU19F8 series, plus Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers Often replaced together with the defrost thermostat and defrost timer/control board as a paired defrost-system repair DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 5304524953 Supersedes 5304523833 Part Type Refrigerator/Freezer Defrost Heater Assembly Condition Genuine OEM Application Refrigerators and Upright Freezers (Frigidaire/Electrolux platform) Location Mounted near the evaporator coils Approximate Weight 1.60 lbs Often Paired With Defrost Thermostat, Defrost Timer/Control Board Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Don't Touch Heater with Bare Hands Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heater only by its mounting brackets or end terminals — do NOT touch the heating element directly with bare fingers; skin oils can cause hot spots and shorten the heater's life. The defrost heater is mounted near the evaporator coils, behind the rear interior access panel of the freezer compartment. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access. If there's a heavy ice sheet covering the back wall, allow the freezer to thaw completely or carefully manually defrost the coils before continuing — never break ice off the coils, as this damages the aluminum fins. Once the area is clear, remove the screws securing the rear access panel and lift it away to expose the evaporator coils and the defrost heater. Photograph the wire connections and heater orientation before disconnecting. Disconnect the wire harness connectors from the old heater, release the heater from its mounting clips or brackets, and lift it out. Install the new 5304524953 heater in the same position, ensuring it's properly seated in the mounting brackets, and reconnect the wire harness. While the panel is open, inspect the defrost thermostat for damage — if it's brittle, discolored, or shows visible defects, this is the ideal time to replace it as well. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves, safety glasses. Frequently Asked Questions How do I know if the defrost heater has failed? The most reliable sign is heavy frost or ice buildup on the evaporator coils behind the freezer back panel — when the heater can't melt the frost as designed, ice accumulates until it blocks airflow and cooling efficiency drops. You may also notice the freezer or fresh food section running warm, the compressor running continuously, or food spoiling faster than normal. To confirm with the refrigerator unplugged: remove the rear freezer access panel, disconnect the heater's wire harness, and test the heater's terminals with a multimeter set to continuity mode. A working heater shows continuity (low resistance); a failed heater shows an open circuit (infinite resistance). If you measure no continuity, the heater has burned out and needs replacement. Should I replace the defrost thermostat and timer at the same time? Yes, it's strongly recommended. The defrost heater, defrost thermostat, and defrost timer/control board work together as a system — the timer (or control board on newer models) initiates the defrost cycle, the thermostat monitors the temperature at the coils and terminates the cycle when the coils are above freezing, and the heater provides the heat that melts the frost. When one component fails, the others have typically experienced similar age and stress, and a near-term failure of another defrost component is common. Since the rear access panel must already be off and the components are right next to each other, replacing all three in a single session prevents a repeat repair down the road. Should I manually defrost my freezer before installing the new heater? If there's significant ice buildup on the evaporator coils or rear wall, yes — you need to clear it before installing the new heater. Leave the freezer empty and unplugged with the door open for 12–24 hours (or longer for heavy ice) to let everything thaw naturally. Place towels at the base to catch melt water. Do NOT chip or pry ice off the evaporator coils with any tool — the aluminum fins damage easily and a damaged coil is a far more expensive repair. Once everything is fully thawed and dried, you can proceed with the heater replacement. My refrigerator/freezer has multiple defrost heater-related part numbers — which one do I need? Frigidaire/Electrolux uses different defrost heater part numbers across different generations and models. The 5304524953 is specifically used in the Frigidaire Professional 19 cu. ft. single-door FPRU19F8 series refrigerators and FPFU19F8 series upright freezers, plus a smaller set of related Frigidaire-platform models. Before ordering, confirm your refrigerator or freezer's model number is in the compatibility list above, or check your appliance's parts diagram to verify that 5304524953 (or one of its cross-references 5304523833, AP6997296, PS16227227, 4975045) is the correct part for your specific model. If your unit is a side-by-side, French door, or other style, you may need a different defrost heater. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same defrost heater assembly installed in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and freezers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

809069201 Refrigerator Genuine OEM Evaporator Fan Motor Fits specific Frigidaire, Electrolux refrigerator models. Description: This Evaporator Fan Motor is an OEM part for specific Frigidaire refrigerator models. It circulates air over the evaporator coils and throughout the refrigerator and freezer compartments, ensuring even cooling and maintaining the desired temperatures. Replaces Part Numbers:809069206, 809069201, AP7014188, PS16544514. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DA32-10105X Refrigerator Temperature Sensor – Compatible with Samsung and Kenmore Refrigerators Product Description Maintain consistent cooling performance with the XPARTCO DA32-10105X Refrigerator Temperature Sensor. This high-quality replacement monitors internal refrigerator temperature and communicates with the control board to regulate cooling cycles. A faulty sensor can cause temperature fluctuations, frost buildup, or over-cooling. Installing this reliable XPARTCO sensor helps restore accurate temperature readings and energy-efficient operation. Replaces Part Numbers DA32-10105X, 2030345, PD00002045, EAP4138686, AP4338786, PS4138686 Compatibility This replacement temperature sensor fits select Samsung and Kenmore refrigerators. Example compatible models include (but are not limited to): Samsung RF28HMEDBSR/AA, RF23HCEDBSR/AA, and Kenmore 795.72053.112. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM accuracy and reliability ❄️ Precision Cooling Control – Ensures stable refrigerator and freezer temperatures 💰 Budget-Friendly Fix – Provides OEM-level performance at a lower cost 🛠️ Easy Installation – Plug-in design for fast and simple replacement 🛡️ Fixes Common Issues – Solves cooling inconsistencies, frost buildup, or warm compartment problems 📐 Product Specification Part Number: DA32-10105X Component Type: Refrigerator Thermistor (Temperature Sensor) Material: Plastic sensor probe with insulated wiring harness Mounting: Clip-in or taped to evaporator wall depending on model Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the existing temperature sensor near the evaporator coil or rear wall. Unplug the old sensor from its wiring harness. Install the new XPARTCO DA32-10105X sensor and reconnect the harness. Secure the sensor in place with clips or adhesive as applicable. Reassemble interior panels and restore power. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator running efficiently — Add to Cart Now for a reliable, cost-effective repair!

Read more less

W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve The W11645245 is a genuine Whirlpool OEM dual water inlet valve for Whirlpool-built refrigerators. Mounted at the rear of the refrigerator where the household water line connects, this single valve is the central control point for water flow to two separate features: the ice maker and the door-mounted water dispenser. When either feature calls for water, this valve's solenoids open to admit it and close again once the request is satisfied — since one valve handles both jobs, a failure here can affect the ice maker, the dispenser, or both at the same time. Common causes of failure include mineral and sediment buildup from the household water supply interfering with the valve's internal operation over time, and electrical faults either in the valve itself or in the refrigerator's electronic control board that signals it. A failing dual water valve produces a recognizable set of symptoms: the door dispenser stops delivering water, the ice maker slows down, stops producing ice, or fails intermittently, water leaking around the valve area, or an audible electronic buzzing or humming sound coming from the back of the refrigerator. It directly replaces AP7208917, W11546685, W11446818, W11563296, and PS16875686. As a genuine OEM part, the W11645245 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve fixes Whirlpool-built refrigerators where the door water dispenser stops working, the ice maker slows down or stops making ice, there's a leak near the valve at the back of the refrigerator, or you hear an electronic buzzing or humming sound. Controls water flow to both the ice maker and water dispenser from a single valve. Replaces AP7208917, W11546685, W11446818, W11563296, PS16875686. Before replacing, rule out a simple mineral clog and a faulty control board signal — both can produce identical symptoms to a failed valve. Common Problems This Part Fixes Water dispenser on the refrigerator door has stopped working Ice maker has slowed down, stopped producing ice, or is malfunctioning intermittently Both the ice maker and water dispenser affected at the same time Water leaking around the valve area at the back of the refrigerator Electronic buzzing or humming sound coming from behind the refrigerator Reduced water flow or pressure at the dispenser Valve that hums but doesn't appear to be passing water through Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator dual water valve directly replaces the following OEM and cross-reference part numbers: W11546685, W11446818, W11563296, AP7208917, AWP46513, K-79524K, N-86-QC N, PD00080446, PS16875686 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dual water valve is compatible with select Whirlpool-built refrigerators across the Whirlpool family of brands, including: Whirlpool refrigerators — WRS series (including WRS321SDHZ08) Maytag, Jenn-Air, and Amana refrigerators (select models) KitchenAid, Magic Chef, Admiral, and Norge refrigerators (select models) Roper refrigerators (select models) Select Kenmore and Ikea refrigerators built on the Whirlpool platform Note: This is a dual-function valve serving both the ice maker and water dispenser from a single unit — it is not a hot/cold laundry-style valve pair. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration Dual water inlet valve — controls water flow to both the ice maker and door water dispenser Resolves "dispenser not working," "ice maker slow or not making ice," "leak near the valve," and "buzzing or humming noise" symptoms caused by valve failure Single central valve simplifies diagnosis and replacement compared to separate dedicated valves Direct drop-in replacement — mounts to the original rear connection point Replaces W11546685, W11446818, W11563296, AP7208917, and PS16875686 Compatible with a wide range of Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair using basic hand tools Product Specifications Part Number W11645245 Part Type Refrigerator Dual Water Inlet Valve (Ice Maker + Dispenser) Condition Genuine OEM Brand Whirlpool Location Rear of refrigerator, at the household water line connection Function Controls water flow to the ice maker and door water dispenser Connection Type 1/2" water line inlet, NPT threaded Quantity 1 valve Compatible Brands Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Refrigerator Before Starting — Have A Towel Ready Disconnect power at the outlet, and shut off the water supply valve behind or below the refrigerator before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear or bottom of the cabinet where the water supply line connects. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the line. Photograph the wiring and water line connections before disconnecting anything. Disconnect the water supply line from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new W11645245 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check the connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the next day to confirm normal operation has returned. Tools needed: Phillips screwdriver, adjustable wrench or pliers, towel or shallow pan, work gloves. Frequently Asked Questions My dispenser stopped working but the ice maker still works. Is this the right part? It's possible, but worth checking a couple of things first, since this valve serves both features from one unit. Confirm the water supply line isn't kinked or restricted, and check the inline water filter for a clog, since a blocked filter can starve the dispenser specifically while the ice maker (which may draw from a different point in the flow path depending on your model) keeps working. If the filter and supply line are clear and the dispenser still won't deliver water, the valve itself is the likely cause. I hear a buzzing or humming sound from the back of the fridge. What does that mean? This is a common symptom of a valve that's receiving an electrical signal to open but isn't passing water through correctly — the solenoid coil energizes and hums, but water flow is restricted or absent, often due to internal mineral buildup or a failing internal mechanism. If you hear this sound whenever the ice maker or dispenser is called on, the valve is a strong suspect. Could the problem actually be my water filter instead of this valve? Yes, it's worth ruling out first. A clogged inline water filter can produce very similar symptoms to a failing valve — reduced dispenser flow, slow ice production, or both. Try replacing the water filter first if it's been a while since the last change; if symptoms persist afterward, the dual water valve is the more likely cause. Could this be a control board issue instead of the valve? It's possible. This valve is triggered electrically by the refrigerator's control board, so a fault there can produce symptoms that look identical to a failed valve — no water reaching the ice maker or dispenser even though the valve itself is fine. If replacing the valve doesn't resolve the issue, the control board is the next component worth investigating. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-function solenoid design and connection configuration as the valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA47-00244QCM Refrigerator Defrost Heater 115V, 120W element with defrost thermostat. Fits FF evaporator in Samsung bottom freezers. Replaces Part Numbers:DA47-00244Q, AP5587899, PS4140528.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

EAU63923602 Refrigerator Genuine OEM Condenser Fan Motor – Compatible with LG & Kenmore Refrigerators Product Description Restore proper airflow and efficient cooling with the EAU63923602 Refrigerator Genuine OEM Condenser Fan Motor. This factory-approved motor circulates air across the condenser coils to help dissipate heat from the refrigeration system. A failed condenser fan motor can cause the refrigerator to run warm, overheat, make loud noises, or stop cooling efficiently. Installing this Genuine OEM condenser fan motor ensures exact fit, quiet operation, and long-lasting performance. Replaces Part Numbers EAU63923602, ODM-001F-4B, PD00057884, EAP12383670, AP6317196, 4877338, PS12383670. Compatibility This Genuine OEM condenser fan motor fits select LG and Kenmore (LG-manufactured) refrigerators. Example compatible models include (but are not limited to):LG LFXS24623S, LFXC24726SKenmore 795.71033.010, 795.74023.411 Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and reliability 🌬️ Restores Proper Airflow – Cools condenser coils for efficient operation 🔇 Quiet Performance – Smooth motor design reduces noise and vibration 💪 OEM-Grade Durability – Built for continuous operation in warm environments 🛡️ Fixes Common Issues – Solves warm temperatures, overheating, or loud fan noise 📐 Product Specification Part Number: EAU63923602 Component Type: Refrigerator Condenser Fan Motor Voltage: 120V AC Mounting: Rear lower condenser fan assembly Rotation: OEM-matched direction Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the refrigerator before servicing. Condenser components may be hot—allow time to cool. Steps: Disconnect power and remove the rear lower access panel. Locate the condenser fan motor assembly. Disconnect the wiring harness and remove mounting screws. Install the new EAU63923602 motor in the same position. Reconnect wiring, reinstall the panel, and restore power. Confirm proper fan operation and airflow. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore efficient refrigerator cooling with confidence — Add to Cart Now for a factory-quality repair!

Read more less

MJU62070602 Genuine LG OEM Refrigerator Water Line Plastic tube, 5/16" - 79 inches in length Replaces Part Number: MJU62070602, 5210JA3004R, 5210JA3004U, MJU62070606, 2676818, 5210JA3004B, 5210JA3029U, AH3536013, EA3536013, MJU62070601, MJU62070611, MJU62070615, AP4681126, PS3536013.  Water tubing MJU62070602 is an original equipment manufacturer (OEM) part that fits some Kenmore, Kenmore Elite and LG refrigerators. Water tubing MJU62070602 supplies water to refrigerator components that require water such as the ice maker and water dispenser. Replaces original refrigerator water tubing part numbers 5210JA3004U, 5210JA3029U, MJU62070601 and MJU62070606. Fits some Kenmore and Kenmore Elite 795-series refrigerators. Also fits some LG refrigerators in these series: LFD, LFX, LMX, LRFD, LRSC and LSC.  

Read more less

XPARTCO 5304512529 Microwave Door Switch – Compatible with Frigidaire, Electrolux, and Kenmore Microwaves Product Description Ensure safe and reliable operation with the XPARTCO 5304512529 Microwave Door Switch. This high-quality aftermarket replacement detects when the microwave door is closed, allowing the appliance to run safely. A faulty switch can cause the microwave not to start, stop mid-cycle, or operate with the door open — a serious safety concern. Replacing it with this durable XPARTCO switch restores proper interlock function and dependable performance. Replaces Part Numbers 5304512529, 4584691, PD00051808, EAP12365114, AP6278576, PS12365114. Compatibility This replacement door switch fits select Frigidaire, Electrolux, and Kenmore microwave models. Example compatible models include (but are not limited to): Frigidaire FFMV1645TS, Electrolux E30MO75HPS, and Kenmore 790.80353310. Always verify your microwave’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to meet OEM safety and performance standards ⚡ Restores Safe Operation – Ensures microwave only operates when the door is securely closed 💰 Budget-Friendly Fix – High-quality alternative to expensive OEM replacements 🛠️ Quick Installation – Direct-fit replacement; installs easily with basic tools 🛡️ Fixes Common Issues – Solves no-start, mid-cycle shutdowns, or unsafe door operation 📐 Product Specification Part Number: 5304512529 Component Type: Microwave Door Interlock Switch Material: Heat-resistant plastic housing with copper terminals Mounting: Snap-in bracket installation Operating Conditions: Designed for high-voltage microwave circuits Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver ⚠️ Safety First: Always unplug the microwave before servicing. Microwave capacitors can retain dangerous voltage even when unplugged — use extreme caution or contact a qualified technician. Steps: Disconnect power and remove the microwave cover. Locate the door latch assembly containing the switches. Disconnect wiring connectors and remove the old switch. Install the new XPARTCO 5304512529 door switch into the same slot. Reconnect wiring, reassemble the cover, and test door operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your microwave’s performance and safety — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less

EAU63923601 Refrigerator Condenser Fan Motor - Compatible with LG, Haier, Kenmore/Sears Refrigerators Product Description Keep your refrigerator cool and efficient with the replacement EAU63923601 Refrigerator Condenser Fan Motor from Parts-O-Matic. This high-quality motor, designed for LG, Haier, and Kenmore/Sears refrigerators, circulates air across the condenser coil to dissipate heat, ensuring optimal cooling performance. Made with durable ABS plastic and metal components (DC 12V, 1A, 4-wire 4-pin), this motor addresses issues like overheating, noisy operation, poor cooling, or fan failure. Note: Includes one condenser fan motor. Disconnect power before installation. Take photos of wiring during disassembly for accurate replacement. Replaces part numbers: EAU63923601, ODM-001F-4A, LFXS26596S, 4877337, AP6317195, PS12383669, EAP12383669, PD00046601, EAU63923604 Compatibility: Compatible with models including but not limited to: LG: LFXS28968S, LFXS28968S/00, LMXS28626S, LMXS28626S/00, LFXS26596S, LRMDS3006S, LMWS27626S, LRFVS3006D Haier: Select models requiring EAU63923601 or compatible condenser fan motors Kenmore/Sears: Select models requiring EAU63923601 or compatible condenser fan motors Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG, Haier, and Kenmore/Sears refrigerator models. 🔥 Specifications: replacement condenser fan motor, DC 12V, 1A, 4-wire 4-pin connector, shaft length 46mm, shaft diameter 3mm, line length 72cm (28.34in), ABS plastic/metal construction, 3.15" x 3.15" x 2.76", 5.29 oz. 💰 Cost-Effective Alternative: replacement motor offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, flathead screwdriver, work gloves; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves issues like refrigerator overheating, excessive noise, poor cooling, or fan failure. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Restore your refrigerator’s cooling efficiency today! Add to cart now for a budget-friendly fix!

Read more less

W10335056 Washer Genuine OEM Water Level Switch Pressure Switch Replaces Part Numbers: W10335056, 1617123, 3366846, AH3408073, EA3408073, AP4566382, PS3408073, W10335056VP.  Description: This Pressure Switch is a Genuine OEM part for specific Whirlpool washing machine models. This part ensures your machine fills with the correct amount of water for the selected cycle, preventing overfilling or insufficient water levels that can lead to suboptimal washing results.    A faulty Pressure Switch can result from several issues, including clogging with detergent residue or debris, wear and tear from regular use, or electrical malfunctions affecting its responsiveness.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM W11844302 Refrigerator Filter Head The W11844302 is a genuine OEM water filter head assembly for Whirlpool refrigerators, and the current part number that supersedes the earlier W11808483. The filter head is the fitting inside the refrigerator that holds the water filter and routes incoming water through it to the water dispenser and ice maker. When the head cracks, leaks, or no longer seats the filter correctly, you can see water at the filter, lose flow to the dispenser or ice maker, or find the filter will not lock in or seal. This is a genuine OEM part from Whirlpool, not an aftermarket equivalent, so the fit and the filter connection match what came with the refrigerator. It is the filter head only. The water filter itself is a separate part and is sold separately. Quick Answer The Genuine OEM W11844302 Filter Head fixes a Whirlpool refrigerator whose filter head is cracked, leaking, or no longer holding or sealing the water filter. Genuine OEM, the current number superseding W11808483 and a long list of earlier Whirlpool filter head numbers. Classic symptom: water dripping around the filter, a filter that won't lock in or seal, or reduced water flow to the dispenser and ice maker. Common Problems This Part Fixes Water leaking from or around the filter head Water filter won't lock in or seal properly Reduced or no water from the dispenser or ice maker traced to the filter head Cracked, broken, or damaged filter head housing Worn filter connection that no longer holds the filter securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This filter head replaces the following part numbers: W11844302, W11346623, W11808483, 12590620, 12590621, 12590622, W10605367, W10861009, WPW10605367, 12590618, W10609243, W11308018, W11791385, AP8114280, AWP1598415. W11844302 is the newest number for this filter head, superseding W11808483. The rest are earlier Whirlpool numbers for it. The source list continues beyond those shown, so additional numbers may exist. If your old filter head or parts diagram shows any of them, match against this list. Compatibility This filter head is listed for: Whirlpool refrigerators, including WRF535SWHZ Note: Filter heads differ between refrigerator models and generations, and no full model list is published for this part. Before ordering, compare your old filter head and its mounting against the Replaces list and your parts diagram, or contact our support team with your model number and we'll verify fit. This is the filter head only. The water filter is sold separately. Key Features Genuine OEM Whirlpool water filter head assembly, not an aftermarket equivalent Current part number, superseding W11808483 and a long list of earlier Whirlpool filter head numbers Restores a secure, leak-free filter connection Filter head only. Water filter sold separately Product Specifications Part Number W11844302 OEM Part Number W11844302 Supersedes W11808483 Part Type Refrigerator Water Filter Head Assembly Condition Genuine OEM Manufacturer Whirlpool Included Filter Head Only Application Select Whirlpool Refrigerators Installation Notes ⚠️ Shut Off Water and Unplug Power Turn off the water supply to the refrigerator and unplug it before starting. Remove the water filter, and have towels ready since some water will remain in the lines. Following your model's service guide, disconnect the water lines from the filter head and remove the screws or fasteners holding it to the refrigerator. Note how the lines and mounting are arranged, install the new filter head in the same position, and reconnect the lines securely. Install the water filter, restore water and power, and check every connection for leaks. Run water through the dispenser for several minutes to flush air from the lines, and check again for leaks. Frequently Asked Questions My water filter leaks or won't seal. Is this the part I need? It can be. Check first that the filter is the correct one for your model and is fully seated. If the filter fits correctly but still leaks, or the head itself is cracked or damaged, replacing the filter head should fix it. Does this include the water filter? No. This is the filter head only. The water filter is sold separately. My old filter head is marked W11808483, W10861009, or W11346623. Will this work? All three numbers are on the Replaces list. Because filter heads vary between models, compare your old head and its mounting against this one, or contact our support team with your model number and we'll confirm before you order. Is this a genuine Whirlpool part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

2187145 Refrigerator Genuine Compressor Overload Replaces Part Numbers: WP2187145, OEM24024106, AP6006026, 2187145, 2-34286-038, 4431117, 8206664, PS11739089, W10306725. Description: This Compressor Overload is a Genuine OEM part for specific Whirlpool, Kenmore refrigerator models.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less