12238200001084 Genuine OEM Midea Dryer Bearing House Assembly (Drum Rear Bearing)
The 12238200001084 is a Genuine OEM Midea replacement bearing house assembly compatible with select Midea, Criterion, and Insignia electric and gas dryers, including the CDE41N1AW series. The bearing house assembly is mounted at the rear of the drum and houses the bearing that the rear drum shaft rotates within, supporting the back of the drum and allowing it to spin smoothly. Unlike front-mounted slide rollers used on some dryer platforms, this Midea design uses a rear bearing housing assembly to carry the load at the back of the drum.
When the bearing house assembly wears out — typically from age, lack of lubrication, or accumulated lint and debris — the drum no longer spins smoothly on its rear support, resulting in grinding, rumbling, or squealing noise, increased drum drag, and in advanced cases, visible wobble or binding of the drum during rotation. As a Genuine OEM part manufactured by Midea to factory specifications, the 12238200001084 is a complete bearing house assembly designed as a direct replacement for the original equipment component. Installs in 45–60 minutes with basic hand tools, as drum removal is required.
Quick Answer
The 12238200001084 Genuine OEM Midea Dryer Bearing House Assembly fixes Midea, Criterion, and Insignia dryers with grinding, rumbling, or squealing noise from the rear of the drum, increased drum drag, or visible drum wobble. Mounted at the rear of the drum — houses the bearing the rear drum shaft rotates within. Genuine OEM. Compatible with Midea CDE41N1AW and related Midea electric dryer platform models. Requires drum removal to access — a more involved repair than a front roller swap.
Common Problems This Part Fixes
Loud grinding or rumbling noise from the rear of the drum during the drying cycle
Squealing or squeaking noise as the drum rotates — worn or dry bearing surface
Increased drag or resistance felt when manually rotating the drum by hand
Drum wobbling or binding during rotation — worn bearing no longer providing stable support
Excessive vibration during the drying cycle
Visible wear, cracking, or lint/debris buildup in the bearing house area
Drum scraping against the rear bulkhead due to lost bearing support
Replaces Part Numbers
This bearing house assembly directly replaces the following part number:
12238200001084, AP7154967, PS18167713
This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This bearing house assembly is compatible with select Midea, Criterion, and Insignia dryers, including:
Midea CDE41N1AW electric dryer
Midea MLE series electric dryers (select models — same drum/bearing platform)
Criterion electric dryers built on the Midea platform (select models)
Insignia electric dryers built on the Midea platform (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
Complete bearing house assembly — supports the rear of the drum and allows smooth, quiet rotation
Houses the bearing that the rear drum shaft rotates within — a sealed-style design intended to resist lint intrusion
Direct replacement for the original equipment bearing house assembly
Compatible with Midea CDE41N1AW and related Midea, Criterion, and Insignia electric dryer platform models
Installs in 45–60 minutes with basic hand tools (drum removal required)
Product Specifications
Part Number
12238200001084
Part Type
Dryer Bearing House Assembly (Drum Rear Bearing)
Condition
Genuine OEM
Application
Electric Dryers (Midea platform)
Location
Rear of drum — houses rear drum shaft bearing
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum. Take a photo of the belt routing before disconnecting the drive belt from the idler pulley. Carefully lift the drum out of the cabinet and set it aside on a padded surface. Locate the bearing house assembly mounted at the rear bulkhead where the drum's rear shaft was seated. Remove the mounting screws or clips securing the old bearing house assembly and pull it free. Clean any accumulated lint or debris from the mounting area before installing the new part. Install the new 12238200001084 bearing house assembly in the same position and secure the mounting hardware. Reinstall the drum, re-route and reconnect the drive belt, and reassemble the front and top panels. Restore power and run a test cycle to confirm the drum rotates smoothly and quietly. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the bearing house assembly do?
The bearing house assembly is mounted at the rear bulkhead of the dryer and houses the bearing that the rear drum shaft rotates within. It supports the back of the drum as it spins, allowing smooth, low-friction rotation throughout the drying cycle. Unlike dryer platforms that use front-mounted slide rollers or felt seals for drum support, this Midea design relies on a dedicated rear bearing housing to carry the structural load at the back of the drum. As the bearing wears, friction increases, leading to noise, drag, and eventually wobble or binding if left unaddressed.
How do I know if the bearing house assembly has failed versus another component?
A grinding, rumbling, or squealing noise specifically tied to drum rotation — rather than the blower motor or idler pulley — and noise that changes pitch as the drum speeds up or slows down often points to the rear bearing. With the dryer unplugged and the drum exposed (front panel removed), try rotating the drum by hand: if you feel noticeable resistance, grinding, or grittiness compared to a smooth, free rotation, the bearing house assembly has likely worn out and needs replacement.
Why does this repair require removing the drum?
The bearing house assembly is mounted at the rear bulkhead behind the drum, supporting the drum's rear shaft from the inside. There is no way to access this component without first removing the front panel and lifting the drum out of the cabinet. This makes it a more involved repair than swapping a front-accessible part like a belt or idler pulley, but it follows the same general dryer disassembly procedure used for accessing other internal drum components.
Should I inspect other components while the drum is out?
Yes — since the drum must already be removed to access the bearing house assembly, this is an excellent opportunity to inspect the drive belt, idler pulley, and any felt seals or gaskets around the drum opening for wear. Components in this drum drive system tend to wear together, and addressing multiple worn parts in a single repair session helps avoid a near-term repeat teardown.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same bearing house assembly installed in compatible Midea, Criterion, and Insignia electric dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine Speed Queen RB170003 Dryer Drum Front Guide Kit - Compatible with Speed Queen, Alliance
Product Description
Ensure smooth and quiet operation of your dryer with the Genuine Speed Queen RB170003 Dryer Drum Front Guide Kit. This OEM glide kit is designed for Speed Queen and Alliance dryers manufactured in 1992 and later, supporting the drum at the front to allow smooth rotation and reduce friction. Made of durable materials, it addresses issues like squeaking, grinding noises, or drum misalignment, delivering reliable performance as an authentic Speed Queen part.
Note: Includes glide pads and sponge cushion. Disconnect power before installation. Wear work gloves to protect your hands. Refer to your parts diagram for a complete list of included parts.
Replaces part numbers: RB170003, AP5186012, 15558045
Compatibility:
Compatible with models including but not limited to:
Speed Queen: ADE3SRGS173TW01, ADE4BRGS175TW01, ADEE9BGS175TW01, ADG3SRGS113TW01, ADG4BRGS115TW01
Alliance: ATGE9AGP113TW01, ADGE9BGS115TW01
Other models: FEU17AWF1702, FGS17AWF, FGU17AWF1702, LES17AWF (verify compatibility)
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Speed Queen and Alliance dryers manufactured in 1992 and later.
🔄 Specifications: OEM glide kit with glide pads and sponge cushion for smooth drum rotation.
💪 Reliable Performance: Authentic Speed Queen part ensures long-lasting durability.
🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 15–30 minutes.
🛡️ Effective Fixes: Resolves squeaking, grinding noises, or drum misalignment issues.
Product Specification
Part Number: Genuine Speed Queen RB170003
Component Type: Dryer drum front glide kit
Material: Plastic glide pads, sponge cushion
Mounting: Bolt-mounted to dryer drum front assembly
Operating Conditions: Suitable for household and commercial dryer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today!
Add to cart now for a reliable fix!
XPARTCO 35001087 Dryer Thermal Cut Off - Compatible with Samsung, Kenmore, Maytag Dryers
Product Description
Safeguard your dryer with the replacement XPARTCO 35001087 Dryer Thermal Cut Off. This thermal cut-off fuse is designed for select Samsung, Kenmore, and Maytag dryers, shutting off the heating element or burner when the dryer overheats to prevent fires or damage. It addresses issues like no heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts.
Note: Includes one thermal cut-off fuse with two 1/4" male spade terminals. Disconnect power before installation.
Replaces part numbers: WP35001087, 35001087, 1122480, PD00003747, EAP11741821, AP6008681, PS11741821.
Compatibility:
Compatible with models including but not limited to:
Samsung: DV203AES, DV209AEW/XAA-0000, DV210AEW/XAA, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2
Kenmore: 40289032010, 40289032011, 40299032010, 40299032012
Maytag: MDE3000AYW, MEDB200VQ0, MEDB850WB0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, Maytag, Amana, and Inglis dryers.
🔥 Specifications: replacement thermal cut-off fuse, opens at 185°F (85°C), 25A at 125/250VAC.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes.
🛡️ Effective Fixes: Resolves no heat, failure to start, or premature shutoff due to overheating.
Product Specification
Part Number: XPARTCO 35001087
Component Type: Thermal cut-off fuse
Material: Plastic and metal
Electrical Specs: 25A at 125/250VAC, opens at 185°F (85°C)
Mounting: Two 1/4" male spade terminals, 1" between mounting holes (center to center)
Operating Conditions: Suitable for high-temperature dryer environments
Compliance: UL-listed components, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and operational today!
Add to cart now for a budget-friendly fix!
XPARTCO WE18X26 Dryer Lint Screen
For gas & electric dryers. Also fits #DE520. Plastic.
Dimensions: The rigid plastic frame typically measures roughly 12 5/8 inches long by 2 3/4 inches wide (though some aftermarket variations list slightly different bracket sizes, the standard inner slot size is uniform).
Replaces Part Numbers: WE18X26, WE18X0019, WE18X0021, WE18X0023, WE18X0024, WE18X0025, WE18X0026, WE18X0027, WE18X0028, WE18X19, WE18X21, WE18X23, WE18X24, WE18X25, WE18X26E, WE18X26R, WE18X27, WE18X28, AH266250, DE520, EA266250, AP2043582, PS266250.
This is an aftermarket part that can be used as a replacement for the OEM part.
RI1V120 Cooktop Re-ignition Spark Module
Re-ignition Module
1 Points Reignition Module
120 Volt
Replaces Part Numbers:
Whirlpool / KitchenAid W11319687, W11121317, AP6872103, PS12711722.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
W10828351 Dryer Genuine OEM Lint Screen with Cover
Replaces Part Numbers: W10828351, 8531964, 8531967, W10812395, 348399, 348400, 4338557, 685273, ER8531964, TJDE964, W10828351VP, AP5985829, PS11726200.
Description: This Lint Screen Cover and Filter is a Genuine OEM part for specific whirlpool, Kenmore Laundry Center dryer models. It serves a dual purpose: the lint screen traps lint and debris from clothes during the drying process, preventing them from clogging the dryer vent, while the cover ensures the lint screen is securely positioned and contributes to optimal airflow within the dryer. Common causes of a bad part include tears or holes in the lint screen that allow lint to pass through and clog the vent, a cracked or broken cover that fails to secure the lint screen properly, or buildup of fabric softener and lint that reduces the effectiveness of the filter.
XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat
The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact.
Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools.
Quick Answer
The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482.
Common Problems This Part Fixes
Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit
Dryer takes much longer than normal to dry a load
Dryer tumbles normally but generates no heat during the cycle
No heat even after the thermal fuse has already been replaced — thermostat also failed
Dryer overheating intermittently — thermostat not opening at the correct temperature
Multimeter test shows open circuit (no continuity) across the thermostat at room temperature
Replaces Part Numbers
This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers:
6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform.
LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models)
LG electric dryers — DLEX series (select models)
LG gas dryers — DLG series (DLG2051W, DLG3788W and related models)
LG gas dryers — DLGX series (select models)
LG electric and gas dryers — DLB series (select models)
Kenmore / Sears dryers — 796-series (LG-built models)
Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both.
Key Features
Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits
Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat
Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers
3-terminal design — matches the original wiring configuration on compatible heater housings
Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center)
Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application
Mounts directly on the heater housing — accessible from the dryer back panel
Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair
Test with multimeter before replacing — should show closed continuity at room temperature
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–20 minutes with basic hand tools
Product Specifications
Part Number
6931EL3001F
Part Type
Dryer Rear Hi-Limit Heater Thermostat
Condition
Aftermarket Replacement
Application
LG and Kenmore Electric and Gas Dryers
Thermostat Rating
L125-31C — auto-resets after cooling
Voltage
250V
Amperage
25A
Terminals
3-terminal
Dimensions
2"L x 1-3/4"W x 1-1/4"H
Mounting Hole Spacing
Approx. 1-5/8" center to center
Color
Gray / Black
Material
Metal / Plastic
Location
Heater housing (rear of dryer)
Normal Behavior
Closed continuity at room temperature
Often Replaced With
6931EL3003D Thermal Fuse
Compatible Brands
LG, Kenmore (LG-built)
Installation Notes
⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter.
Frequently Asked Questions
What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse?
Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended.
How do I test the 6931EL3001F thermostat with a multimeter?
Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat.
My LG dryer has no heat but the thermal fuse is good — could it be the thermostat?
Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition.
What does the "L125-31C" rating mean?
The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 6931EL3001E Dryer Thermostat – Compatible with LG and Kenmore Dryers
Product Description
Maintain proper dryer safety and temperature control with the 6931EL3001E Dryer Thermostat. This replacement part monitors and regulates dryer temperature to prevent overheating and ensure efficient drying cycles. A faulty thermostat may cause your dryer to stop heating, overheat, or shut off unexpectedly. Replacing it restores reliable performance and helps extend the life of your dryer.
Replaces Part Numbers
6931EL3001E, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PD00023869, EAP3530481, AP4440977, PS3530481, L125-31C, 503475.
Compatibility
This dryer thermostat is compatible with select LG and Kenmore dryer models.
Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, and Kenmore 796.80272900.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Broad Compatibility – Fits select LG and Kenmore dryers
🔒 Reliable Safety – Prevents overheating by regulating dryer temperature
💰 Cost-Effective Replacement – OEM-equivalent performance at a lower price
🛠️ DIY-Friendly – Quick installation with basic tools
🛡️ Fixes Common Issues – Restores heating, prevents overheating, and fixes dryer shutdown problems
📐 Product Specification
Part Number: XP6931EL3001E
Component Type: Dryer Thermostat
Material: High-heat resistant metal and thermal components
Mounting: Direct replacement, mounts on heating element housing
Operating Conditions: Designed for residential dryers
Compliance: OEM-equivalent performance and safety standards
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers
⚠️ Safety First: Always disconnect power before starting repairs to avoid electrical shock.
Steps:
Unplug dryer and remove back access panel.
Locate thermostat on heating element housing.
Disconnect wire terminals from the old thermostat.
Remove screws holding it in place and replace with the new thermostat.
Reconnect wires, secure the component, and reinstall the access panel.
Restore power and test dryer operation.
⏱️ Time Required: 15–20 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🛠️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore your dryer’s safe operation today — Add to Cart Now for fast, budget-friendly repair!
Choice Y54414 Dryer Idler Pulley - Compatible with Admiral, Crosley, Maytag, Speed Queen Dryers
Product Description
Keep your dryer running smoothly with the replacement Y54414 Dryer Idler Pulley from Parts-O-Matic. This high-quality aftermarket idler pulley replaces the Whirlpool Y54414, designed for select Admiral, Crosley, Maytag, and Speed Queen dryer models. It maintains proper tension on the drive belt to ensure the dryer drum spins effectively, fixing issues like noisy operation, failure to tumble, or the dryer not starting. Constructed from durable plastic and metal with a satin finish, this pulley measures 2-3/16" in diameter and 3/4" in width. Enjoy fast and free shipping on all orders at Parts-O-Matic! Note: Washers and retaining clips may not be included; reuse existing ones if in good condition. Inspect the idler arm for wear and consider replacing it if damaged.
Replaces part numbers: WPY54414, Y54414, 14218926, 54414, R0609504, WPY54414VP, 54414-REPL, R0609504-REPL, AP6024203, PS11757553, D510142P, 510142P, 510142, D510142, 510142P, 510142, 54414, 54415, 54415P, AP6329060, PS17001032, DE407, 54414-2, 1246423, AP6024203, EAP11757553, PD00002420, PS11757553, 510142P, 510142, D510142P, AP4291235, PS2200898
Compatibility:
Compatible with models including but not limited to:
Admiral: AE series (e.g., AE3213, AE3413, AE4113)
Crosley: CDE series
Maytag: SDG3606AWW, SDG4606AWW, MDET336AYW, SDG405DAWW
Speed Queen: AEE933, AEE953, AEM197, AEM333, AEM353, AEM377, AEM397, AEM407L, AEM427W
Amana: ALG866SBW, LEA60AL
Verify your model number or contact Parts-O-Matic support for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Admiral, Crosley, Maytag, and Speed Queen dryer models.
🔥 Specifications: Idler pulley with 2-3/16" diameter x 3/4" width, made of plastic and metal with a satin finish, includes metallic bearing for smooth operation.
💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires a Phillips screwdriver, snap ring pliers, and basic tools; typically installed in 15–30 minutes. Washers and retaining clips may not be included.
🛡️ Reliable Fixes: Resolves issues like noisy operation, drum not spinning, or dryer not starting.
Installation Notes:
Tools Needed: Phillips screwdriver, snap ring pliers, flathead screwdriver, work gloves.
Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation.
Handle with Care: Inspect the idler arm shaft for wear; lubricate with powdered graphite or light machine oil for smoother operation.
Installation Steps: Access the idler pulley by removing the dryer’s front panel and drum (consult your model’s manual for specific screws). Remove the old pulley by releasing the snap ring, washer, and belt. Clean the idler arm shaft, then install the new pulley with existing or new washer, pulley, second washer, and snap ring. Rethread the belt around the pulley and motor pulley (check your model’s belt routing diagram). Reassemble in reverse order. Note: Snap ring pliers are recommended for easy removal and installation. If the idler arm is worn, consider replacing the entire assembly.
Shop Parts-O-Matic for high-quality aftermarket appliance parts with fast and free shipping on all orders and a 30-day return policy. Get your dryer back to quiet, efficient performance today!
XPARTCO WE01X25316 Dryer Door Catch
The XPARTCO WE01X25316 is an aftermarket replacement dryer door catch (also called a door latch) compatible with a wide range of GE and Hotpoint electric and gas dryers in the GTD, GTX, ETD, HTX, NTX, PTD, and YTD series. The door catch is the spring-loaded latch mechanism mounted inside the dryer door panel that snaps onto the door strike on the dryer cabinet when the door is closed, holding the door securely shut during operation and activating the door switch so the dryer can run. When the catch breaks or loses its spring tension, the door will not stay closed, the dryer will not start, or the door will pop open during a drying cycle.
This replacement catch is constructed from toughened nylon with a hardened manganese steel spring — materials chosen for superior wear resistance and spring durability compared to standard nylon. It is sold individually and mounts inside the dryer door panel using a snap-in clip retained by a metal retaining ring. Installation requires partially disassembling the dryer door to access the catch from the inside. It directly replaces 4512762, AP6037347, EAP11766999, PD00042653, and PS11766999. Installs in 15–30 minutes with basic tools.
Quick Answer
The XPARTCO WE01X25316 Dryer Door Catch fixes GE and Hotpoint dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Toughened nylon body with manganese steel spring. Sold individually. Mounts inside the door panel — door must be partially disassembled for installation. Compatible with GE GTD3–GTD8, GTX, ETD, HTX, NTX, PTD, and YTD series dryers. Replaces 4512762, AP6037347, EAP11766999, PD00042653, PS11766999.
Common Problems This Part Fixes
Dryer door will not stay closed during the drying cycle
Door pops open mid-cycle, stopping the dryer
Dryer will not start — door switch not being activated by worn or broken catch
Door feels loose or does not click firmly when closed
Door catch visibly cracked, broken, or spring missing
Door requires being held or pushed closed to keep the dryer running
Replaces Part Numbers
This door catch directly replaces the following OEM and cross-reference part numbers:
WE01X25316, 4512762, AGE24874, AP6037347, EAP11766999, PD00042653, PS11766999
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door catch is compatible with select GE and Hotpoint gas and electric dryers from the following series:
GE dryers — GTD3, GTD4, GTD5, GTD6, GTD7, GTD8 series (GTD33EASK0WW, GTD42EASJ1WW, GTD58EBSV0WS, GTD65EBPL0DG, GTD72EBSN0WS, GTD75ECPL0DG, GTD84ECPN0DG and related models)
GE dryers — GTX2, GTX3, GTX4, GTX6 series (GTX22EASK0WW, GTX33EASK0WW and related models)
GE dryers — ETD48 series (ETD48GASW0WB and related models)
GE dryers — PTD6, PTD7, PTD9 series (PTD60EBPR1DG and related models)
GE dryers — YTD7 series (YTD74E2PN2DG and related models)
GE dryers — XTD series (XTD72E8ST1WS and related models)
Hotpoint dryers — HTX2, HTX24 series (HTX21EASK0WW, HTX24EASK0WW, HTX24GASK0WS and related models)
Hotpoint dryers — NTX6 series (NTX62E8ST0WW and related models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Holds the dryer door closed and activates the door switch so the dryer can run safely
Toughened nylon body — superior wear resistance compared to standard nylon catches
Hardened manganese steel spring — provides reliable, durable spring tension for thousands of open/close cycles
Snap-in design — mounts inside the door panel with a metal retaining clip
Replaces 4512762, AP6037347, EAP11766999, and PS11766999
Sold individually — one door catch per order
Compatible with GE GTD, GTX, ETD, HTX, NTX, PTD, and YTD series dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
WE01X25316
Part Type
Dryer Door Catch (Door Latch)
Condition
Aftermarket Replacement
Application
GE and Hotpoint Gas and Electric Dryers
Material
Toughened nylon / Hardened manganese steel spring
Mounting
Snap-in inside the door panel — metal retaining clip secures in place
Sold As
Single door catch
Compatible Brands
GE, Hotpoint
Installation Notes
⚠️ Unplug Dryer Before Starting — Door Disassembly Required Unplug the dryer before beginning. Unlike simpler snap-in door catches, the WE01X25316 is mounted inside the dryer door panel and requires partially disassembling the door to access it. Open the dryer door and remove the screws on the latch side of the door (typically three screws) and the screws on the hinge side (typically five screws). Gently pry the door inner and outer panels apart — work carefully around the edge. With the panels separated, locate the old catch — use pliers to squeeze the gray retaining tabs together and push downward to release the catch from the inner panel. With needle-nose pliers, squeeze the metal retaining clip and apply downward force until the clip is free. Insert the new WE01X25316 catch into the panel opening and snap it into place, then press the retaining clip back on to lock it. Reassemble the door panels and reinstall all screws. Close the door to confirm it latches firmly. Restore power and run a short cycle to verify normal operation. Tools needed: drill driver with 1/4" bit, #1 square head bit, pliers, needle-nose pliers.
Frequently Asked Questions
Why does installation require disassembling the door?
Unlike the snap-in door catches found on many Whirlpool-family dryers — which clip into a slot accessible from the front without disassembly — the WE01X25316 mounts inside the GE door panel between the inner and outer door skins. This is a GE-specific design that provides a cleaner door exterior but requires separating the two door panels to access and replace the catch. While it is more involved than a simple snap-in replacement, it is a well-documented DIY repair that most homeowners can complete in 15–30 minutes with the right tools.
My dryer door closes but the dryer still won't start — is it the catch?
It may be — a worn or cracked catch may not push far enough into the door strike to fully activate the door switch, even if the door appears closed. However, if the catch appears intact and snaps firmly onto the strike, the issue may be with the door switch itself rather than the catch. The door switch (located inside the dryer cabinet at the door opening) can be tested with a multimeter for continuity in the open and closed positions. If the switch tests open in both positions, it has failed and needs replacement independently of the door catch.
Is this compatible with older GE dryers that have a different door catch style?
The WE01X25316 is for newer GE GTD, GTX, HTX, and related series dryers. Older GE dryers used a different door catch kit — most notably the WE01X1158 / WE1M536 / WE1M1011 style, which is a separate catch and strike kit. If your GE dryer is an older model not in the GTD/GTX/HTX series listed above, verify your model number before ordering to confirm this is the correct catch for your dryer.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from toughened nylon with a hardened manganese steel spring to match the dimensions and function of the original WE01X25316 door catch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPU6602-001655 Dryer Drum Belt
(Made in USA)
5 Rib, 92"
Drum Belt Replaces: 6602-001655, 6602-001314, AP4373659, PS4133825.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
