Search results for "refrigerator damper"

5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat The 5303918214 is a genuine Frigidaire OEM defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. As a genuine OEM part, the 5303918214 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Genuine Frigidaire OEM part — factory-specified temperature threshold and mounting configuration Defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Genuine OEM Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original temperature threshold, mounting configuration, and function of the defrost thermostat originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator cooling evenly with the XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor. This Fan Motor is a replacement component for specific LG, Kenmore refrigerator models. It operates the circulation fan located in the back of the refrigerator compartment, distributing cool air evenly throughout. The motor enables constant airflow across shelves and compartments to maintain consistent temperatures and humidity levels. Causes of a bad fan motor include failure of bearings or windings due to prolonged use. Replaces Part Numbers 4681JB1029A, EAU60694507, 1330410, 4681JB1010C, 4681JB1017A, 4681JB1017D, 4681JB1027A, EAU61762902, EAU41921810, PD00037982, EAP3523328, AH3523328, EA3523328, AP4438221, PS3523328.  Compatibility This replacement evaporator fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25960ST, LG LFX28968ST, and Kenmore 795.77543600. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to meet OEM airflow and reliability standards ❄️ Efficient Air Circulation – Distributes cold air evenly through refrigerator and freezer 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Simple plug-in wiring connector for quick installation 🛡️ Fixes Common Issues – Solves frost buildup, uneven cooling, or noisy fan problems 📐 Product Specification Part Number: 4681JB1029A Component Type: Refrigerator Evaporator Fan Motor Material: Metal motor housing with balanced plastic fan blade Mounting: Direct-fit replacement in freezer evaporator compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before performing repairs to prevent electrical shock. Steps: Unplug the refrigerator. Remove shelves and freezer rear panel to access the evaporator area. Disconnect the wiring harness and mounting screws on the old fan motor. Install the new XPARTCO 4681JB1029A motor, reconnect wiring, and secure the panel. Restore power and verify quiet, consistent airflow. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore efficient, even cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

Genuine OEM EAU65058315 Refrigerator Evaporator Fan Motor The Genuine OEM LG EAU65058315 is a DC evaporator fan motor assembly for select LG and Kenmore refrigerators. The evaporator fan motor circulates cold air through the refrigerator, helping to keep temperatures consistent and prevent frost buildup. When it wears out or fails, the refrigerator may run too warm or too cold, build up frost, or make unusual noise. This is the original LG part, not an aftermarket equivalent. It is the evaporator fan, not the condenser fan near the compressor. Check your model number before ordering. Quick Answer The Genuine OEM EAU65058315 Evaporator Fan Motor replaces the evaporator fan motor on a compatible LG or Kenmore refrigerator when it has failed. Classic symptoms: the refrigerator or freezer is too warm, frost builds up, or the fan makes unusual noise. Other parts can cause the same symptoms, so confirm the fan is the problem first. Common Problems This Part Fixes Refrigerator or freezer too warm or too cold Frost buildup Unusual noises from the fan area Moisture or water leaking Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This evaporator fan motor is listed under the following part number: EAU65058315 replaces EAU63103209, ODM-056F-15, ALG54104, AP6247423, EAP12115088, PD00081425, PS12115088, PS17308826, AP7211789 LG uses many similar fan motor numbers for different models. If your old motor shows a different number, contact our support team and we'll check whether it matches. Compatibility This evaporator fan motor is listed for LG, Kenmore and Kenmore Elite bottom-mount refrigerators, including these examples: LG LFX25974SW, LFCS22520S, LFDS22520S Kenmore 79570339411, 79579412811, 79579412810 Kenmore Elite 79579049314, 79579044313 Note: The models above are a sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM LG part, not an aftermarket equivalent DC motor assembly Circulates cold air through the refrigerator Helps keep temperatures consistent and prevent frost buildup Product Specifications Part Number EAU65058315 OEM Part Number EAU65058315 Part Type Refrigerator Evaporator Fan Motor Condition Genuine OEM Manufacturer LG Motor Type DC Application Select LG, Kenmore & Kenmore Elite Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator and move perishable food to a cooler before you begin. Wear work gloves. Follow your model's service guide to reach the evaporator fan, note how the wiring connects, and swap the motor. Reconnect the wiring, restore power, and check that the fan runs quietly. Frequently Asked Questions My refrigerator is running warm. Is this the part I need? It can be, if the evaporator fan has failed. Other parts can cause the same symptoms, so check that the fan isn't blocked by frost and that the fan itself isn't spinning before replacing it. Is this the evaporator fan or the condenser fan? This is the evaporator fan motor, which circulates cold air through the refrigerator. The condenser fan motor is a different part, located near the compressor. Is this an OEM or aftermarket part? This is a genuine OEM part from LG, not an aftermarket equivalent. Will this fit my refrigerator? It is listed for select LG, Kenmore and Kenmore Elite bottom-mount models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

67006390 Refrigerator Hv Control Box   Replaces Part Numbers: WP67006390, 67006390, 12957601, 12957601SP, 4435670, AP6010509, PS11743690.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve The W11645245 is a genuine Whirlpool OEM dual water inlet valve for Whirlpool-built refrigerators. Mounted at the rear of the refrigerator where the household water line connects, this single valve is the central control point for water flow to two separate features: the ice maker and the door-mounted water dispenser. When either feature calls for water, this valve's solenoids open to admit it and close again once the request is satisfied — since one valve handles both jobs, a failure here can affect the ice maker, the dispenser, or both at the same time. Common causes of failure include mineral and sediment buildup from the household water supply interfering with the valve's internal operation over time, and electrical faults either in the valve itself or in the refrigerator's electronic control board that signals it. A failing dual water valve produces a recognizable set of symptoms: the door dispenser stops delivering water, the ice maker slows down, stops producing ice, or fails intermittently, water leaking around the valve area, or an audible electronic buzzing or humming sound coming from the back of the refrigerator. It directly replaces AP7208917, W11546685, W11446818, W11563296, and PS16875686. As a genuine OEM part, the W11645245 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve fixes Whirlpool-built refrigerators where the door water dispenser stops working, the ice maker slows down or stops making ice, there's a leak near the valve at the back of the refrigerator, or you hear an electronic buzzing or humming sound. Controls water flow to both the ice maker and water dispenser from a single valve. Replaces AP7208917, W11546685, W11446818, W11563296, PS16875686. Before replacing, rule out a simple mineral clog and a faulty control board signal — both can produce identical symptoms to a failed valve. Common Problems This Part Fixes Water dispenser on the refrigerator door has stopped working Ice maker has slowed down, stopped producing ice, or is malfunctioning intermittently Both the ice maker and water dispenser affected at the same time Water leaking around the valve area at the back of the refrigerator Electronic buzzing or humming sound coming from behind the refrigerator Reduced water flow or pressure at the dispenser Valve that hums but doesn't appear to be passing water through Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator dual water valve directly replaces the following OEM and cross-reference part numbers: W11546685, W11446818, W11563296, AP7208917, AWP46513, K-79524K, N-86-QC N, PD00080446, PS16875686 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dual water valve is compatible with select Whirlpool-built refrigerators across the Whirlpool family of brands, including: Whirlpool refrigerators — WRS series (including WRS321SDHZ08) Maytag, Jenn-Air, and Amana refrigerators (select models) KitchenAid, Magic Chef, Admiral, and Norge refrigerators (select models) Roper refrigerators (select models) Select Kenmore and Ikea refrigerators built on the Whirlpool platform Note: This is a dual-function valve serving both the ice maker and water dispenser from a single unit — it is not a hot/cold laundry-style valve pair. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration Dual water inlet valve — controls water flow to both the ice maker and door water dispenser Resolves "dispenser not working," "ice maker slow or not making ice," "leak near the valve," and "buzzing or humming noise" symptoms caused by valve failure Single central valve simplifies diagnosis and replacement compared to separate dedicated valves Direct drop-in replacement — mounts to the original rear connection point Replaces W11546685, W11446818, W11563296, AP7208917, and PS16875686 Compatible with a wide range of Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair using basic hand tools Product Specifications Part Number W11645245 Part Type Refrigerator Dual Water Inlet Valve (Ice Maker + Dispenser) Condition Genuine OEM Brand Whirlpool Location Rear of refrigerator, at the household water line connection Function Controls water flow to the ice maker and door water dispenser Connection Type 1/2" water line inlet, NPT threaded Quantity 1 valve Compatible Brands Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Refrigerator Before Starting — Have A Towel Ready Disconnect power at the outlet, and shut off the water supply valve behind or below the refrigerator before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear or bottom of the cabinet where the water supply line connects. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the line. Photograph the wiring and water line connections before disconnecting anything. Disconnect the water supply line from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new W11645245 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check the connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the next day to confirm normal operation has returned. Tools needed: Phillips screwdriver, adjustable wrench or pliers, towel or shallow pan, work gloves. Frequently Asked Questions My dispenser stopped working but the ice maker still works. Is this the right part? It's possible, but worth checking a couple of things first, since this valve serves both features from one unit. Confirm the water supply line isn't kinked or restricted, and check the inline water filter for a clog, since a blocked filter can starve the dispenser specifically while the ice maker (which may draw from a different point in the flow path depending on your model) keeps working. If the filter and supply line are clear and the dispenser still won't deliver water, the valve itself is the likely cause. I hear a buzzing or humming sound from the back of the fridge. What does that mean? This is a common symptom of a valve that's receiving an electrical signal to open but isn't passing water through correctly — the solenoid coil energizes and hums, but water flow is restricted or absent, often due to internal mineral buildup or a failing internal mechanism. If you hear this sound whenever the ice maker or dispenser is called on, the valve is a strong suspect. Could the problem actually be my water filter instead of this valve? Yes, it's worth ruling out first. A clogged inline water filter can produce very similar symptoms to a failing valve — reduced dispenser flow, slow ice production, or both. Try replacing the water filter first if it's been a while since the last change; if symptoms persist afterward, the dual water valve is the more likely cause. Could this be a control board issue instead of the valve? It's possible. This valve is triggered electrically by the refrigerator's control board, so a fault there can produce symptoms that look identical to a failed valve — no water reaching the ice maker or dispenser even though the valve itself is fine. If replacing the valve doesn't resolve the issue, the control board is the next component worth investigating. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-function solenoid design and connection configuration as the valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EAU61524007 Refrigerator Evaporator Fan Motor 13V, 1.5 W, 0.118A. 1-1/2" shaft. Has quick disconnect. Fits specific LG Refrigerator Models. Description:  This ERP EAU61524007 Refrigerator Evaporator Fan Motor is designed for reliable and efficient cooling performance. It features the EAU61524007 model, providing optimal airflow and preserving freshness in your refrigerator. Upgrade your appliance with this high-quality fan motor and enjoy the benefits of improved cooling and longer-lasting food. Replaces Part Numbers:EAU61524007, AP5950081, EAU60694510, PS10058947   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO BPV-31 Refrigerator Refrigerant Piercing Valve / Line Tap Valve Kit The XPARTCO BPV-31 is a universal bullet piercing tap valve (line tap valve) used to quickly access a sealed refrigerant line on refrigerators, freezers, window air conditioners, dehumidifiers, and other HVAC systems — without soldering or brazing. The valve clamps around a copper refrigerant line and, when the valve stem is tightened with the included hex key, a hardened piercing needle punctures the tubing to create an access port. This lets a technician connect a charging hose or gauge to check pressure, pull a vacuum, or add refrigerant to a system that has no factory service port. It's a staple tool for appliance service and DIY refrigerator/freezer repair. Fits 1/4", 5/16", and 3/8" outside diameter copper pipes with the included adapters. The access port connection is a 1/4" male flare fitting. Rated to 500 PSI maximum, with a patented permanent gasket providing over 180 inch-lbs of sealing force — around 50 times the sealing area of a standard O-ring type valve — pressure tested at 250°F. Corrosion-resistant metal (zinc alloy) construction with a piercing needle engineered for concentricity and hardness to seat perfectly every time. Non-positional mounting requires no separate adapter valve and only 2" of clearance for installation. Each kit includes the piercing valve, a hex key wrench, and 2 adapters. It replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Quick Answer The XPARTCO BPV-31 Refrigerant Piercing Valve Kit taps into a sealed copper refrigerant line to add refrigerant, check pressure, or pull a vacuum — no soldering required. Fits 1/4", 5/16", and 3/8" OD pipes. 1/4" male flare port connection. 500 PSI max, patented gasket (50x the sealing area of an O-ring). Zinc alloy metal. Includes piercing valve, hex key, and 2 adapters; only needs 2" clearance. Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31. Not suitable for R410a systems. Common Uses This Kit Serves Adding refrigerant to a refrigerator or freezer that has no factory service port Checking system pressure on a sealed refrigerant line for diagnostics Pulling a vacuum on a system during service Recharging window air conditioners and dehumidifiers Confirming whether a sealed system has lost its refrigerant charge (leak diagnosis) Providing temporary or service access to copper refrigerant tubing without brazing Reviving a garage/shop refrigerator or freezer that has slowly lost its charge Accessing R-12, R-22, R-134a, and other compatible refrigerant systems (NOT R410a) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This bullet piercing tap valve directly replaces the following OEM and cross-reference part numbers: BPV-31, BPV31, BPV31D, AP4502525, GPV14, GPV31, GPV38, GPV56, MPV31 The BPV-31 is a universal valve that covers the GPV-series (GPV14, GPV31, GPV38, GPV56) and MPV31 across the pipe sizes they individually served. Contact our support team if you need help confirming the correct valve for your line size. Compatibility This bullet piercing valve is a universal tool compatible with sealed refrigerant systems using copper tubing, including: Refrigerators and freezers — all major brands with 1/4", 5/16", or 3/8" OD copper refrigerant lines Window air conditioners — for recharging and pressure checks Dehumidifiers — sealed refrigerant systems Other HVAC systems with compatible copper line sizes Refrigerant compatibility — works with R-12, R-22, R-134a and other common refrigerants Important — NOT for R410a Systems: This BPV-31 piercing valve is NOT rated for R410a refrigerant systems, which operate at significantly higher pressures than the valve's design allows. Using it on an R410a system is unsafe. Before use, confirm your line's outside diameter (1/4", 5/16", or 3/8") and select the correct included adapter. Verify the pipe size before installation. Key Features Bullet piercing tap valve — taps a sealed copper refrigerant line to create an access port without soldering or brazing Fits 1/4", 5/16", and 3/8" outside diameter copper pipes (with included adapters) 1/4" male flare access port connection for charging hoses and gauges 500 PSI maximum pressure rating Patented permanent gasket — over 180 inch-lbs of sealing force, ~50 times the sealing area of a standard O-ring type valve; pressure tested at 250°F Piercing needle engineered for concentricity and hardness to seat perfectly every time Corrosion-resistant zinc alloy metal construction — won't rust or wear out over time Non-positional mounting — no separate adapter valve required, installs in any orientation Compact design needs only 2" of clearance for installation and use Each kit includes: 1 piercing valve, 1 hex key wrench, 2 adapters Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31 NOT suitable for R410a refrigerant systems Product Specifications Part Number XPBPV-31 Part Type Bullet Piercing Tap Valve (Line Tap Valve Kit) Condition Aftermarket Replacement Application Refrigerators, Freezers, Window AC, Dehumidifiers, HVAC (sealed copper lines) Compatible Pipe Sizes 1/4", 5/16", 3/8" outside diameter Port Connection 1/4" Male Flare Maximum Pressure 500 PSI Sealing Force 180+ inch-lbs (patented gasket, ~50x O-ring sealing area) Pressure Tested 250°F Material Corrosion-resistant zinc alloy metal Mounting Non-positional, 2" clearance required Kit Includes 1x Piercing Valve, 1x Hex Key, 2x Adapters Not Compatible With R410a refrigerant systems Installation Notes ⚠️ Refrigerant Safety Warning Working with sealed refrigerant systems can expose you to pressurized refrigerant, which can cause frostbite, eye injury, and other harm. Wear safety glasses and protective gloves before piercing any line. Refrigerant handling may be regulated in your area — certain refrigerants require EPA certification (in the US) to purchase and handle. Never vent refrigerant to the atmosphere. This valve is NOT rated for R410a systems (too high pressure). If you're not experienced with refrigerant systems, have this work done by a qualified HVAC or appliance technician. ⚠️ Installation Steps — Clean the Line First Put on safety glasses and protective gloves. Identify the copper line you want to tap and confirm its outside diameter (1/4", 5/16", or 3/8") so you can select the correct included adapter. Clean the section of pipe where the valve will mount to prevent debris from entering the refrigerant line. Ensure the composite seal "O" ring/gasket is properly in place inside the valve. Place the two halves of the valve saddle around the pipe using the appropriate adapter insert for your pipe size. Install and evenly tighten the socket-head screws to clamp the valve body firmly around the pipe. To pierce the line, turn the valve stem clockwise with the included hex key until the needle punctures the tubing, then back the stem out (counterclockwise) to open the port and allow flow. To connect a gauge or charging hose: remove the cap, attach your hose to the 1/4" flare port, and open the valve by turning the stem counterclockwise. When finished, close the valve (turn the stem clockwise) BEFORE disconnecting the hose, then reinstall the protective cap. Note: the compact valve needs only 2" of clearance around the pipe. Tools needed: Included hex key wrench, safety glasses, protective gloves. (Note: to attach a gauge directly to the BPV, a retrofit valve adapter may be required — not included.) Frequently Asked Questions What is a bullet piercing valve used for? A bullet piercing valve (line tap valve) lets you tap into a sealed copper refrigerant line to create an access port — without cutting, soldering, or brazing the line. Most household refrigerators and freezers are sealed systems with no factory service port, so if you need to check the refrigerant pressure, pull a vacuum, or add refrigerant, a piercing valve gives you that access quickly. It clamps around the pipe, and a needle pierces the tubing when you tighten the valve stem. It's commonly used in appliance repair and HVAC service, and by DIYers reviving a garage refrigerator or freezer that has lost its charge. Which pipe sizes does this fit? The BPV-31 fits 1/4", 5/16", and 3/8" outside diameter copper pipes using the included adapters. Before installing, measure or confirm your refrigerant line's outside diameter and select the matching adapter insert. Getting the size right is essential for a proper seal — an incorrectly sized adapter won't clamp tightly and can leak. If you're not sure of your line size, measure the outside diameter of the copper tubing with calipers or a pipe gauge. Can I use this on an R410a system? No — the BPV-31 is NOT rated for R410a refrigerant systems. R410a operates at significantly higher pressures than older refrigerants like R-12, R-22, and R-134a, and exceeds the safe working pressure of this valve (500 PSI max). Using it on an R410a system is unsafe and could result in valve failure or refrigerant release. This valve is appropriate for lower-pressure systems using R-12, R-22, R-134a, and similar refrigerants. For R410a systems, use service equipment specifically rated for R410a pressures. Is a piercing valve a permanent solution? Piercing valves are best thought of as a service-access tool rather than a permanent fixture. They work reliably for tapping into a line to diagnose, vacuum, or charge a system, and the BPV-31's patented gasket provides a much stronger seal than basic O-ring valves. However, for a long-term permanent service port, many technicians prefer to cut the line and braze in a proper Schrader service port. Some technicians have concerns about the very long-term sealing of any piercing valve left permanently on a line. If you leave the valve installed, make sure the stem is closed and the cap is in place, and check periodically for leaks. Do I need EPA certification to add refrigerant? In the United States, handling many refrigerants (and purchasing them) requires EPA Section 608 certification, and it is illegal to intentionally vent refrigerant to the atmosphere. Regulations vary by refrigerant type and jurisdiction. The piercing valve itself is a tool that anyone can install, but the refrigerant handling that follows may be regulated. If you're a DIYer, research the rules that apply to your specific refrigerant and location, or have the refrigerant work done by a certified technician. Always recover refrigerant properly rather than venting it. Is this an OEM or aftermarket part? This is an aftermarket universal service tool built to OEM-equivalent quality standards. The BPV-31 is a universal industry-standard bullet piercing valve design (also sold as Supco BPV31 and equivalent), manufactured from corrosion-resistant zinc alloy to match the fit, 1/4"/5/16"/3/8" pipe compatibility, 1/4" flare port, 500 PSI rating, and patented-style sealing gasket of the standard BPV-31 line tap valve. It replaces AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice DA32-10109Y Refrigerator Temperature Sensor – Replacement for Samsung Product Overview The DA32-10109Y Refrigerator Temperature Sensor is an aftermarket replacement part designed to measure and relay internal temperatures to the control board. A faulty sensor can lead to cooling problems, temperature fluctuations, or improper defrost cycles. Replacing a worn sensor with this reliable component helps restore accurate temperature readings and optimal cooling performance in your refrigerator. 8-1/4" overall length with two pin plug for freezer. Fits Samsung SXS refrigerator models. Replaces Part Numbers This sensor replaces part numbers DA32-10109Y, AP4136950, PS4138703. It is engineered to match the fit and functionality of the original Samsung sensor. Compatible Brands Compatible with many Samsung and Kenmore refrigerators manufactured by Samsung. Fits French door, bottom-freezer, and side-by-side models that use this temperature sensor. Fixes the Following Issues Refrigerator not cooling properly Freezer too warm or too cold Temperature reading errors Inconsistent cooling or defrost operation Why Buy from Parts‑O‑Matic Affordable and dependable aftermarket part Fast and free U.S. shipping Easy to install – no special tools required Trusted by appliance techs and DIYers

Read more less

WFCB Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Replaces Part Numbers: WFCB, WF1CB, 218670303, 218710901, 218710902, 218717805, 218904602, 240389101, 240389102, 240394501, 242007903, 277187, 5303917752, 5303917836, 5303917937, 5303918017, 5304461598, 9906, 9906P, 9910, AH503627, EA503627, FRWFCB, AP2591529, PS503627, RC-101, RC-200, RC101, RC200, RENEW1CB, RENEWFCB, RG100, WF1CB-, WFB, WFCB-

Read more less

5231JA2006F Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Cross Reference Number: 5231JA2006G, 5231JA2006F, AP6889576, PS12724531, LT600P, LT600P/PC/PCS

Read more less

WR60X10209 (OE) Refrigerator Condenser Fan Motor The WR60X10209 is an OE (Original Equipment) DC condenser fan motor for GE refrigerators. This motor lives in the compressor/machine compartment at the back or bottom of the refrigerator. Whenever the compressor runs, this fan runs right along with it, circulating air across the condenser coils to help dissipate heat from the hot refrigerant before it moves on to the evaporator, keeping the compressor from overheating and the whole system running efficiently. Rated 11.3V DC, 2.2W, with a 4-pin plastic plug carrying 4 wires (white, blue, red, and yellow). The motor shaft measures 1/8" in diameter and 2-7/8" long. Common failure causes include worn motor bearings, dirty or obstructed condenser coils forcing the motor to work harder than intended, and general electrical wear. Symptoms include increased noise when the freezer door is opened, warm temperatures inside the refrigerator, and — left unaddressed — compressor overheating and food spoilage from a refrigerator that can no longer maintain temperature. It directly replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, AP4265957, and PS1483567. Quick Answer The WR60X10209 (OE) Refrigerator Condenser Fan Motor fixes GE, Hotpoint, RCA, and select Kenmore refrigerators with increased noise near the compressor compartment, warm temperatures inside the fridge, or early signs of compressor overheating. 11.3V DC, 2.2W, 4-pin/4-wire plug, 1/8" x 2-7/8" shaft. Replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, AP4265957, PS1483567. This is the 12V DC condenser fan — if your refrigerator needs a 120V motor, see our WR60X10220 listing instead. Common Problems This Part Fixes Increased noise near the compressor compartment or when the freezer door is opened Warm temperatures inside the refrigerator Refrigerator running constantly as it struggles to maintain temperature Compressor overheating from restricted airflow around the condenser coils Food spoilage from a refrigerator that can't hold a consistent temperature Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand What Is an OE Part? OE (Original Equipment) means this part is manufactured by the same original supplier that produces the Genuine OEM version — identical fit, materials, and performance. The only difference is packaging: OE parts ship under our XPARTCO brand rather than the appliance manufacturer's branded box, which is why they can't be listed as Genuine OEM. You get factory-original quality at a more affordable price. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator condenser fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10209, 1195784, WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, 045900390950, 197D2407P013, AGE29194, AH1483567, EA1483567, EAP1483567, AP4265957, PD00001176, PS1483567. The motor's own sticker also references production number 197D2407P013. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This condenser fan motor is compatible with select GE and Hotpoint refrigerators, and also fits select RCA and Kenmore refrigerators built on the GE platform. Note — 12V DC, not 120V: This is the 12V DC condenser fan motor. If your refrigerator calls for a 120V motor instead, you need our WR60X10220 listing. This is also a condenser fan (cools the compressor and condenser coils), not an evaporator fan (circulates cold air to the food compartments) — a different part from our WR60X10074, WR60X10185, and WR60X10318 evaporator fan motor listings. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features OE (Original Equipment) condenser fan motor — draws air across the condenser coils to cool the refrigerant and compressor Resolves "noise near the compressor," "warm fridge temperatures," and "compressor overheating" symptoms caused by fan failure Rated 11.3V DC, 2.2W 4-pin plastic plug with 4 wires (white, blue, red, yellow) 1/8" diameter x 2-7/8" long shaft Direct drop-in replacement matching the original mounting and blade fitment Replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, AP4265957, and PS1483567 Compatible with GE, Hotpoint, RCA, and select Kenmore refrigerators Product Specifications Part Number WR60X10209 Designation OE (Original Equipment) Part Type Refrigerator DC Condenser Fan Motor Brand GE Location Compressor/machine compartment (back or bottom of cabinet) Function Cools the condenser coils and compressor Voltage 11.3V DC Wattage 2.2 W Connector 4-pin plastic plug, 4-wire (white, blue, red, yellow) Shaft 1/8" diameter x 2-7/8" long Quantity 1 fan motor Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Danger — Authorized Service Part Required For Flammable Refrigerant Systems GE's own service guidance carries an explicit warning for this component: it is a manufacturer-authorized service part intended for use in refrigerator models that use a flammable refrigerant, such as R600a. Using an unauthorized or incorrectly rated service part in a unit that uses a flammable refrigerant could lead to a risk of fire or explosion. Before ordering or installing, confirm your refrigerator's refrigerant type and verify this part is correct for your specific model. If you have any doubt about your refrigerant type or the correct part for your unit, contact our support team with your model number before proceeding, or have a qualified appliance technician perform this repair. ⚠️ Unplug Refrigerator Before Starting Shut off power at the circuit breaker or fuse box, then pull the refrigerator away from the wall and disconnect the power cord from the outlet. Wear work gloves. Remove the condenser fan motor cover, typically held on by two screws, to access the motor. Before condemning the motor, clear away any dust, lint, or debris built up around the condenser coils and fan blade — restricted airflow from a dirty coil produces symptoms similar to a failing motor and costs nothing to rule out. Photograph the wiring and the fan blade's position before disconnecting anything. Disconnect the 4-pin plug from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR60X10209 in the same position, reconnect the 4-pin plug fully, and confirm the blade spins freely by hand without contacting the housing before reinstalling the fan cover. Restore power and monitor the refrigerator over the next 24 hours to confirm normal, even cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions Why is there a fire/explosion warning on this part? Some refrigerators use a flammable refrigerant, such as R600a (isobutane), instead of older non-flammable refrigerants. Electrical components like fan motors sit near refrigerant lines and can be a source of ignition if a leak were ever present, which is why GE specifically requires an authorized, correctly rated service part for these systems rather than a generic substitute. This isn't a concern unique to this listing — it reflects GE's general guidance for electrical components used in flammable-refrigerant refrigerators, and confirming your model and refrigerant type before ordering is the appropriate precaution. My refrigerator is noisy and runs warm. Is this the condenser fan? It's a strong possibility, especially if the noise seems to come from the back or bottom of the unit and you notice both symptoms together. Without proper airflow across the condenser coils, heat builds up in the machine compartment, which reduces the whole refrigeration cycle's efficiency and shows up as warmer-than-normal temperatures throughout the fridge. Could dirty condenser coils cause the same symptoms as a bad fan motor? Yes, and it's worth checking before you buy a new motor. A condenser fan pushing air through coils caked in dust, pet hair, or debris will struggle to cool the system properly even if the motor itself is working fine. Clean the coils and the fan blade thoroughly first; if the fan still doesn't spin freely, spins with a wobble, or doesn't run at all afterward, the motor itself has failed and this replacement is the correct fix. Is this a genuine OEM part? This is an OE (Original Equipment) part sold under our XPARTCO brand. OE parts are manufactured by the same original supplier that produces the Genuine OEM part, so the fit, materials, and performance are identical — the difference is that OE parts ship in XPARTCO packaging rather than the appliance manufacturer's branded box, which is why we can't list them as Genuine OEM. This gives you factory-original quality at a more affordable price than the branded version. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP W10498976 Refrigerator Water Valve Description: This replacement Part is a single coil water inlet valve intended for use in specific refrigerator models. The valve serves as a solenoid-operated switch that controls the release of water from the supply line into the ice maker mold when activated. This part is crucial to the proper functioning of the refrigerator's ice-making or water dispensing systems. Replaces Part Numbers: WPW10498976, W10498976, W10420082, AP6022334, PS11755667. 

Read more less