Search results for "hvac switch"

6931EL3003 CM Dryer High Limit Thermostat 110C/240F Resettable. Fits select LG and Kenmore dryer models. Replaces Part Numbers: 6931EL3003C, AP4457603, PS3530484, 6931EL3003, L3003 Description: This High Limit Thermostat is a replacement part for specific LG dryer models. This safety component is designed to monitor and regulate the dryer's temperature, preventing it from exceeding safe levels. Mounted on the heating chamber or exhaust duct, the high limit thermostat shuts off the heat source or the dryer itself if it detects temperatures that are too high, helping to prevent overheating and potential fire hazards.  This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

5303917625CM Refrigerator Defrost Thermostat L47-22F tube mount with bullet connectors. Fits Electrolux refrigerator. Replaces Part Numbers: 5303917625, 08000805, 3001234, 3015138, 3916083, 5308000805, 636974, 8000805, AH468968, EA468968, G000166153, AP2592599, PS468968.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WR55X10025 Genuine OEM GE Refrigerator Temperature Sensor The WR55X10025 is a genuine GE OEM temperature sensor, also called a thermistor, for GE, Hotpoint, and Kenmore refrigerators. This sensor measures air temperature inside the refrigerator or freezer compartment and reports it continuously to the main control board, which uses that reading to regulate the cooling cycle. On some models, this same sensor design also serves as the defrost sensor mounted on the evaporator coil, monitoring temperature there to help manage the defrost cycle. Because the control board relies entirely on this sensor's reading to make cooling decisions, a failing or inaccurate sensor can cause the refrigerator to run too cold, too warm, or run for excessively long periods as it tries to correct a temperature it's misreading. On models where it doubles as a defrost sensor, a failure here can also contribute to frost or ice buildup in the freezer. This is a relatively inexpensive part, and it's commonly the actual cause behind symptoms that get mistakenly blamed on the main control board. It directly replaces AP3185407, 914093, AH304103, EA304103, PS304103, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11150, WR55X11151, and WR55X11152. Quick Answer The WR55X10025 Genuine OEM GE Refrigerator Temperature Sensor fixes GE, Hotpoint, and Kenmore refrigerators that run too cold, too warm, run for excessively long periods, or (on models where this sensor doubles as a defrost sensor) show frost or ice buildup in the freezer. A healthy sensor reads approximately 5,000 ohms at 77°F. Replaces AP3185407, 914093, AH304103, EA304103, PS304103, and a wide range of WR50X/WR55X-prefix numbers listed below. This is an inexpensive part that's frequently the actual cause behind symptoms mistakenly blamed on the main control board — worth testing or replacing before assuming a costlier board repair is needed. Common Problems This Part Fixes Refrigerator running too cold Refrigerator running too warm Refrigerator running for excessively long periods Freezer not defrosting properly (on models where this sensor also serves as the defrost sensor) Freezer too cold or showing frost buildup Display temperature reading that doesn't match the actual temperature inside the compartment Inconsistent or fluctuating cooling performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator temperature sensor directly replaces the following OEM and cross-reference part numbers: WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select GE, Hotpoint, and Kenmore refrigerators, and is used broadly across most GE side-by-side and French door refrigerator configurations. Note: While this sensor is used across a very broad range of GE refrigerator models, always verify your full model number before ordering, since some models use a different sensor design. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified resistance curve for accurate temperature reporting Measures air temperature and reports it continuously to the main control board Also used as a defrost sensor on the evaporator coil on select models Resolves "too cold," "too warm," "runs too long," and "display reading doesn't match actual temperature" symptoms Direct drop-in replacement — matches the original mounting and wiring Replaces a wide range of WR50X and WR55X-prefix part numbers listed above Compatible with GE, Hotpoint, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically completed in under an hour Product Specifications Part Number WR55X10025 Part Type Refrigerator Temperature Sensor (Thermistor) Condition Genuine OEM Brand GE Function Measures compartment or evaporator temperature and reports it to the control board Typical Resistance Approx. 5,000 ohms at 77°F Repair Difficulty Easy — typically under 1 hour Quantity 1 temperature sensor Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Danger — Authorized Service Part Required For Flammable Refrigerant Systems GE's own service guidance carries an explicit warning for this component: it is a manufacturer-authorized service part intended for use in refrigerator models that use a flammable refrigerant, such as R600a. Using an unauthorized or incorrectly rated service part in a unit that uses a flammable refrigerant could lead to a risk of fire or explosion. Before ordering or installing, confirm your refrigerator's refrigerant type and verify this part is correct for your specific model. If you have any doubt about your refrigerant type or the correct part for your unit, contact our support team with your model number before proceeding, or have a qualified appliance technician perform this repair. ⚠️ Unplug Refrigerator Before Starting — Test With A Multimeter Before Replacing Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Before replacing, it's worth testing the old sensor with a multimeter set to ohms — a healthy sensor reads approximately 5,000 ohms at 77°F; a reading well outside that range, or an open circuit, confirms a failed sensor. Locate the sensor, typically mounted on an interior wall of the compartment or clipped to the evaporator coil depending on your model. Photograph the wiring and mounting position before disconnecting anything. Disconnect the sensor's wire connector, remove any mounting clip or bracket, and pull the old sensor free. When positioning the new WR55X10025, make sure it sits in open air away from direct contact with ice buildup areas, since ice touching the sensor can cause it to read colder than the compartment's actual temperature. Reconnect the wire connector and secure the mounting clip. Restore power and monitor the refrigerator over the next 24 hours, comparing the display temperature to an independent thermometer placed in the compartment to confirm accuracy. Tools needed: multimeter, work gloves. Frequently Asked Questions How do I test whether this sensor has actually failed? Use a multimeter set to ohms and test the sensor across its two terminals. A healthy sensor typically reads approximately 5,000 ohms at 77°F room temperature; a reading significantly outside that range, or no reading at all (open circuit), confirms the sensor has failed and should be replaced. My display shows a temperature that doesn't match how cold the fridge actually feels. Could positioning be the issue, not the sensor itself? Yes, this is a documented and somewhat subtle failure mode. If the sensor ends up positioned too close to an area where ice or frost accumulates, the ice's surface temperature can pull the sensor's reading colder than the actual compartment air temperature, causing the display to show a colder number than reality — sometimes off by several degrees. One customer traced exactly this issue to ice buildup near the sensor location and resolved it by ensuring the new sensor sat clear of that ice-prone area during installation. Could my problem actually be the control board instead of this sensor? It's worth testing this sensor first before assuming a control board issue. This is a relatively inexpensive part, and it's commonly the actual root cause behind symptoms that get misdiagnosed as a control board failure, since the board is only ever as accurate as the temperature data it receives. Testing or simply replacing this sensor is a low-cost step worth taking before pursuing a more expensive board repair. Why is there a fire/explosion warning on this part? Some refrigerators use a flammable refrigerant, such as R600a (isobutane), instead of older non-flammable refrigerants. Electrical components near refrigerant lines can be a source of ignition if a leak were ever present, which is why GE requires an authorized, correctly rated service part for these systems rather than a generic substitute. Confirming your model and refrigerant type before ordering is the appropriate precaution. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the temperature sensor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X25198 Dryer Genuine OEM Thermostat Fits Specific GE Dryer Models.  Replaces Part Numbers: WE04X25198, 4467032, AP6024634, PS11736631. Description: This Thermostat is a Genuine OEM component specifically designed for specific GE laundry machine models. It is a heat-sensing component that monitors and regulates air temperatures inside the dryer drum. Precise thermostat functioning ensures proper drying temperatures are reached and maintained for optimal performance.  

Read more less

XPARTCO DA97-20025A Refrigerator Condenser Fan Motor The XPARTCO DA97-20025A is an aftermarket replacement condenser fan motor for Samsung French door, Flex 4-door, and side-by-side refrigerators. This small DC motor lives in the compressor compartment at the back or bottom of the refrigerator, and its job is to pull air across the condenser coils and the compressor itself to carry heat away from the refrigeration system. That's a very different job from an evaporator fan — the condenser fan cools the mechanical side of the system rather than circulating cold air to your food, so a failing condenser fan affects the whole refrigerator's cooling capacity rather than just one compartment. Rated at 12V DC, 0.11A. When this fan slows down or stops, the compressor and condenser coils can't shed heat properly, which makes the whole system work harder and less effectively — both the fresh food and freezer compartments can run warm together, the compressor may run hot and cycle off on thermal protection, and you may notice increased noise or heat coming from the back or bottom of the cabinet. Common failure modes include worn motor bearings, a jammed blade from dust and debris buildup around the condenser coils, or electrical failure of the motor windings. It directly replaces PD00076495, 4962138, AP6883701, PS12720104, and EAP12720104. Quick Answer The XPARTCO DA97-20025A Refrigerator Condenser Fan Motor fixes Samsung French door, Flex 4-door, and side-by-side refrigerators where both compartments run warm together, the compressor runs hot or trips out, the refrigerator runs constantly, or there's unusual noise from the back or bottom of the cabinet. 12V DC, 0.11A. Replaces PD00076495, 4962138, AP6883701, PS12720104, EAP12720104. This cools the compressor and condenser coils — a different part and a different symptom pattern than an evaporator fan, which only affects internal air circulation. Common Problems This Part Fixes Both the fresh food and freezer compartments running warmer than normal at the same time Refrigerator running constantly as the compressor struggles to keep up Compressor running unusually hot, or shutting off on thermal overload protection Unusual noise — humming, buzzing, or grinding — coming from the back or bottom of the refrigerator Ice maker not producing ice due to overall insufficient cooling Noticeably higher energy use as the compressor works harder to compensate Fan blade in the compressor compartment that doesn't spin freely or spins with a wobble when checked by hand Excessive dust or debris buildup visible around the condenser coils and fan Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator condenser fan motor directly replaces the following OEM and cross-reference part numbers: DA97-20025A, 12 DC 0.11A 2122CNW Z19W12MS1A5-52K09, 4962138, AP6883701, ASM814341, EAP12720104, PD00076495, PS12720104.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This condenser fan motor is compatible with select Samsung French door, Flex 4-door, and side-by-side refrigerators, including model numbers such as: RF27T5241SR, RF27T5201SR, RF27T5201SG, RF27T5501SR RF28T5001SG, RF28T5001WW, RF28T5021SR, RF29BB8600QL, RF29BB860012 RF32CG5400SR, RF32CG5300SR, RF32CG5100SR RF18A5101SR, RF22A4221SR, RF29A9071 RS22T5201SR, RS27T5200SG, RS27T5200SR, RS28A500ASR, RS28CB7600QL Note — condenser fan, not evaporator fan: This motor cools the compressor and condenser coils in the machine compartment at the back or bottom of the refrigerator. It is a completely different part from an evaporator fan motor (such as our DA31-00334C or DA81-06013A listings), which sits behind the freezer's rear panel and circulates cold air to the food compartments. The two fail with different symptom patterns: a condenser fan problem tends to warm the whole refrigerator evenly and stress the compressor, while an evaporator fan problem typically leaves the freezer relatively fine while the fresh food side goes warm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Aftermarket replacement condenser fan motor — draws air across the condenser coils and compressor to remove system heat Resolves "whole fridge running warm," "compressor overheating," "runs constantly," and "noise from the back or bottom" symptoms caused by fan failure Rated 12V DC, 0.11A Optimized fan blade and motor design for efficient heat dissipation with reduced operating noise High-quality ball bearings for extended service life Direct drop-in replacement matching the original mounting and blade fitment Replaces PD00076495, 4962138, AP6883701, PS12720104, and EAP12720104 Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DA97-20025A OEM Part Number DA97-20025A Part Type Refrigerator Condenser Fan Motor Condition Aftermarket Replacement Brand Samsung Location Compressor/machine compartment (back or bottom of cabinet) Function Cools the condenser coils and compressor Voltage 12V DC Amperage 0.11 A Quantity 1 fan motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Access is from the rear or bottom of the refrigerator, depending on your model: remove the rear access panel, or pull the unit out and remove the base grille/toe-kick panel at the bottom to reach the compressor compartment. Before condemning the motor, clear away any dust, lint, or debris built up around the condenser coils and fan blade — restricted airflow from a dirty coil produces similar symptoms to a failing motor and costs nothing to rule out. Photograph the wiring harness connector and the fan blade's position before disconnecting anything. Unplug the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and carefully pull the motor and fan blade assembly free. Transfer the fan blade to the new motor if it isn't included, matching the original orientation. Mount the new DA97-20025A in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing or coils before reassembling the access panel. Restore power and monitor the refrigerator over the next 24 hours to confirm normal, even cooling has returned and the compressor is no longer running hot. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Both my fresh food and freezer sections are warm. Is this the right part? Yes, that pattern points toward the condenser fan rather than an evaporator fan. Because the condenser fan cools the compressor and condenser coils that the entire refrigeration cycle depends on, a failing condenser fan tends to reduce cooling capacity across both compartments together, rather than leaving one side fine while the other struggles. If only your fresh food section is warm while the freezer stays cold, that's more typical of an evaporator fan issue instead. My compressor feels very hot and the fridge cycles off sometimes. Could that be the fan? Very possibly. Without adequate airflow from the condenser fan, the compressor and coils can't shed heat efficiently, causing the compressor to run hotter than designed. Many compressors have built-in thermal overload protection that shuts them down temporarily if they overheat, which can show up as the refrigerator seeming to randomly stop and restart cooling. Restoring proper condenser airflow is often what resolves this. Could dirty condenser coils cause the same symptoms as a bad fan motor? Yes, and it's worth checking before you buy a new motor. A condenser fan pushing air through coils caked in dust, pet hair, or debris will struggle to cool the system properly even if the motor itself is working fine. Clean the coils and the fan blade thoroughly first; if the fan still doesn't spin freely, spins with a wobble, or doesn't run at all afterward, the motor itself has failed and this replacement is the correct fix. Do I need this motor or an evaporator fan motor? It depends on the symptom and the fan's location. The condenser fan sits in the compressor compartment at the back or bottom of the refrigerator and cools the compressor and coils — a failure here tends to warm the whole unit and stress the compressor. An evaporator fan sits behind the freezer's rear interior panel and circulates already-cold air to the compartments — a failure there typically leaves the freezer relatively unaffected while the fresh food section goes warm. If you're not sure which fan has failed, check which one is running (or not) by listening near each location with the refrigerator open and the door switch triggered manually, or contact our support team with your model number. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications (12V DC, 0.11A), fan blade design, and mounting configuration of the original DA97-20025A condenser fan motor used in compatible Samsung refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XP382 Dryer Gas Valve Solenoid for DC62-00201A The XP382 is an aftermarket replacement gas valve solenoid coil kit for Samsung gas dryers, and also fits select Whirlpool, Sears, and Kenmore models using a compatible two-coil gas valve. This is a newer-style coil kit that fits most dryers using a two-coil gas valve design, and it works alongside the gas valve assembly (DC62-00201A) to regulate the precise amount of gas needed to properly combust and generate heat for drying clothes. Over time, these solenoid coils can weaken or fail electrically, preventing the gas valve from opening correctly even when the igniter is functioning normally. Symptoms of a failing gas valve solenoid include the burner not igniting even though the igniter glows, weak or inconsistent heat, or the dryer running a full cycle with little to no heat. Quick Answer The XP382 Dryer Gas Valve Solenoid fixes Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve, where the burner isn't igniting despite the igniter glowing, heat is weak or inconsistent, or the dryer runs without heating. Fits Samsung DC62-00201A gas valve assembly. This is a gas ignition component — always shut off the gas supply and let the dryer cool before working on it, and if you smell gas at any point, stop and call a professional. Common Problems This Part Fixes Burner not igniting even though the igniter glows normally Weak or inconsistent heat Dryer running a full cycle with little to no heat Gas valve failing to open when the igniter calls for gas Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer gas valve solenoid directly replaces the following OEM and cross-reference part numbers: Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This gas valve solenoid is compatible with select Samsung gas dryers using the DC62-00201A gas valve assembly, and also fits select Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve design. Note: This is a coil kit that works with the gas valve assembly, not a replacement for the full valve body itself. If your gas valve assembly needs full replacement rather than just the coils, you'll need the complete DC62-00201A assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dryer needs. Key Features Aftermarket replacement gas valve solenoid coil kit Resolves "burner won't ignite," "weak heat," and "no heat" symptoms tied to gas valve solenoid failure Newer-style coil kit fitting most two-coil gas valve designs Direct drop-in replacement matching the original mounting and connection Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A Compatible with Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil valve Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP382 OEM Part Number DC62-00201A (compatible coil kit) Part Type Dryer Gas Valve Solenoid Coil Kit Condition Aftermarket Replacement Coil Configuration Two-coil Application Gas Dryers Repair Difficulty Moderate — gas appliance component Quantity 1 solenoid coil kit Compatible Brands Samsung, Whirlpool, Sears, Kenmore Installation Notes ⚠️ Shut Off Gas Supply And Unplug Dryer Before Starting This is a gas ignition component. Turn off the gas supply to the dryer at the shutoff valve and disconnect power at the outlet before beginning. Allow the dryer to cool fully if it has recently been in use. Wear work gloves. If you smell gas at any point during this repair, stop immediately, do not operate any switches, leave the area, and contact your gas utility or a qualified technician from a safe location. Access the gas valve assembly, typically located near the burner housing — consult your dryer's service documentation for the exact access point on your model. Locate the old solenoid coils and disconnect their wiring. Remove the mounting screws or clips securing the old coils to the valve body and pull them free. Install the new XP382 coils in the same position, reconnect the wiring fully, and secure the mounting hardware. Restore the gas supply and power, then test the burner to confirm it ignites reliably with consistent heat. If you are not fully comfortable working with gas line connections, have a qualified technician perform this repair instead. Frequently Asked Questions My igniter glows but the burner doesn't light. Is this the part I need? Yes, this is a classic sign of a failed gas valve solenoid. The igniter can glow and reach ignition temperature normally, but if the solenoid coils that open the gas valve have failed electrically, no gas reaches the burner to actually ignite, leaving the dryer to run without heat. Do I need the whole gas valve assembly, or just this coil kit? If the valve body itself is intact and only the solenoid coils have failed, this coil kit is the more targeted and typically less expensive repair. If the valve body is cracked, stuck, or otherwise physically damaged, you'll need the complete DC62-00201A gas valve assembly instead. Is it safe to replace this myself? This repair involves working around your dryer's gas supply line, so take care to fully shut off the gas and let the appliance cool before starting. If you're not comfortable working around gas appliances, or if you smell gas at any point, stop and contact a qualified technician or your gas utility rather than continuing the repair yourself. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the coil configuration and connection type needed to work with the DC62-00201A gas valve assembly used in compatible Samsung, Whirlpool, Sears, and Kenmore gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators. Product Overview The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward. A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area. Quick Answer WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase. Common Problems This Part May Fix Ice dispenser door will not open Ice chute door will not close Ice maker makes ice but ice will not dispense Chute door sticks or operates intermittently Warm air enters around the dispenser chute Frost or moisture develops around the dispenser opening Replaces and Cross-References WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796 Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number. Compatibility Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include: GI7FVCXWY00 KSCS25FTMS02 KSRS25FTSS01 KSCS23FVMS02 KSRS25RSBT01 KSCS25FVMS01 KSCS25FTSS00 GC3NHAXVA00 106.56702500 Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering. Key Features Genuine Whirlpool OEM part Operates the ice dispenser chute door Replaces W10184813 and 2305262 For select Whirlpool-built side-by-side and French-door refrigerators Helps restore proper dispenser-door opening and closing Product Specifications Manufacturer Part Number WPW10184813 Brand Whirlpool Part Type Refrigerator Ice Dispenser Door Motor Condition New Quality Genuine OEM Application Ice Dispenser Chute Door Package Quantity 1 Motor Installation Notes Disconnect refrigerator power before service. Remove the dispenser trim and front components according to the appliance service procedure. Photograph connector and mechanical linkage positions before disassembly. Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor. Transfer or reconnect the wiring and linkage exactly as originally installed. Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service. Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts. Frequently Asked Questions Is WPW10184813 a Genuine Whirlpool OEM part? Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor. Does it replace W10184813? Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262. What does this motor do? It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing. Will it fit every Whirlpool refrigerator? No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision. Shop With Confidence Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering. Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping

Read more less

DE47-20034A Microwave Genuine High Limit Thermostat Thermal cutout. High limit thermostat. Open for continuity at room temperature, closes when it gets hot. Fits Samsung over counter microwaves. Replaces Part Numbers:DE47-20034A, AP4219754, PS4226431.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 0130F00010 Gas Furnace Flame Sensor Fits the Specific Goodman Gas Furnace models Replaces Part Numbers:TJFLS013, AP6326767, 0130F00010   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Choice 8557403 Dryer Thermostat  Replaces Part Numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386 Description: This Dryer Thermostat is a replacement part for select Kenmore, Maytag, Whirlpool dryer models. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 6931EL3001E Dryer Thermostat – Compatible with LG and Kenmore Dryers Product Description Maintain proper dryer safety and temperature control with the 6931EL3001E Dryer Thermostat. This replacement part monitors and regulates dryer temperature to prevent overheating and ensure efficient drying cycles. A faulty thermostat may cause your dryer to stop heating, overheat, or shut off unexpectedly. Replacing it restores reliable performance and helps extend the life of your dryer. Replaces Part Numbers 6931EL3001E, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PD00023869, EAP3530481, AP4440977, PS3530481, L125-31C, 503475. Compatibility This dryer thermostat is compatible with select LG and Kenmore dryer models. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, and Kenmore 796.80272900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits select LG and Kenmore dryers 🔒 Reliable Safety – Prevents overheating by regulating dryer temperature 💰 Cost-Effective Replacement – OEM-equivalent performance at a lower price 🛠️ DIY-Friendly – Quick installation with basic tools 🛡️ Fixes Common Issues – Restores heating, prevents overheating, and fixes dryer shutdown problems 📐 Product Specification Part Number: XP6931EL3001E Component Type: Dryer Thermostat Material: High-heat resistant metal and thermal components Mounting: Direct replacement, mounts on heating element housing Operating Conditions: Designed for residential dryers Compliance: OEM-equivalent performance and safety standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before starting repairs to avoid electrical shock. Steps: Unplug dryer and remove back access panel. Locate thermostat on heating element housing. Disconnect wire terminals from the old thermostat. Remove screws holding it in place and replace with the new thermostat. Reconnect wires, secure the component, and reinstall the access panel. Restore power and test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s safe operation today — Add to Cart Now for fast, budget-friendly repair!

Read more less

WR55X10956 Refrigerator Main Control Board Replaces Part Numbers:WR55X10956, 1550509, WR55X10657, WR55X10658, WR55X10662, WR55X10697, WR55X10745, WR55X10774, WR55X10929, WR55X10943, WR55X10958, AH2371144, EA2371144, AP4481481, PS2371144.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less