Search results for "washer water valve"

WP389386 Washer Lower Agitator  Fits Specific Top Load Washer Models. Replaces Part Number: WP389386, 389386, 2418, 99989683, AP6008839, PS11741980. Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.

Read more less

WH07X10019 Washer Drive Pulley  Genuine GE part Replaces Part Number: WH07X10019, 1264466, AH1482349, EA1482349, AP3995204, PS1482349, WH07X10018.

Read more less

XPARTCO WH01X20826 Washing Machine Shock Absorber The XPARTCO WH01X20826 is an aftermarket replacement shock absorber (damper) for GE front-load washers. The wash tub inside a front-load washer hangs suspended inside the cabinet, and a set of these shock absorbers is what controls that movement — dampening the tub's vibration and motion during spin so it doesn't bang against the cabinet or shake the whole machine. These washers typically use four shock absorbers working together around the tub, and this listing is for a single individual shock absorber. Over time the internal damping material in these shocks wears out, or the shock can physically separate from its mounting point — something that can also happen if the washer is moved or shifted without the tub properly secured first. Because all four shocks on a given washer are typically the same age and under the same stress, if one has failed the others are often not far behind — many technicians recommend ordering four of this same part and replacing the full set together as a preventative measure. A worn or detached shock absorber produces a very recognizable symptom: excessive vibration, shaking, or banging noise during the spin cycle, sometimes strong enough that the washer visibly moves or "walks" across the floor. It directly replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Quick Answer The XPARTCO WH01X20826 Washing Machine Shock Absorber fixes GE front-load washers (and select Hotpoint, Haier, Monogram, Café, and Kenmore models built on the GE platform) that vibrate, shake, or bang excessively during spin, or seem to "walk" across the floor. Sold as a single individual shock absorber. Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. These washers use four shock absorbers total — if one has failed, order four of this part to replace the full set, since they wear on the same schedule. Common Problems This Part Fixes Excessive vibration or shaking during the spin cycle Loud banging or knocking noise from inside the cabinet during spin Washer that seems to "walk" or move across the floor during operation Tub striking the cabinet frame or nearby panels Shock absorber that has visibly separated or detached from its mounting point Noise or vibration that started or worsened after the washer was moved or relocated Visible wear, cracking, or looseness in the shock absorber material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washing machine shock absorber directly replaces the following OEM and cross-reference part numbers: WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select GE front-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: GE uses several different shock absorber part numbers across its washer lineup, including separate parts such as WH01X10727 and WH03X29516 for other platforms. This WH01X20826 shock is specific to the front-load models listed above and is not interchangeable with those other GE shocks. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement shock absorber — dampens tub vibration and movement during spin Sold individually — order four to replace the full set on a typical front-load washer Resolves "excessive vibration," "banging or knocking noise," and "washer walking across the floor" symptoms caused by worn or detached shocks Durable plastic and rubber construction for long-term damping performance Direct drop-in replacement — no modification required Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Compatible with GE, Hotpoint, Haier, Monogram, Café, and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH01X20826 OEM Part Number WH01X20826 Part Type Washing Machine Shock Absorber (Damper) Condition Aftermarket Replacement Application GE Front-Load Washers Material Plastic and rubber Function Dampens tub vibration and movement during spin Typical Quantity Per Washer 4 (this listing is for 1 individual shock) Quantity 1 shock absorber Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Consider Replacing All Four Shocks Together Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shock absorbers typically requires removing the top and/or front panel of the washer to reach the tub suspension points — check your model's service diagram, since access varies. Photograph how each old shock absorber connects to the frame and the tub before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Disconnect the old shock absorber from its mounting point at both the frame and tub ends, and remove the mounting pin. Install the new shock absorber in the same position with its mounting pin, matching the original orientation. If you're only replacing one shock, be aware the remaining three original shocks are the same age and under the same stress — many technicians recommend ordering three more of this same part and replacing all four together to avoid reopening the washer again soon after. Once installed, gently rock the tub by hand to confirm even resistance at each corner before reassembling the panels. Restore power and run a full spin cycle to confirm the vibration, shaking, or banging noise has resolved. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I need to order more than one of these? This listing is for a single shock absorber, but GE front-load washers use four of them working together around the tub. If one has failed, it's strongly worth ordering four total and replacing the full set, since all four are typically the same age and have been under the same stress — replacing just one risks having to reopen the washer again soon after for the next one. My washer started shaking right after I moved it to a new spot. Is that related? Yes, this is a documented cause of shock absorber problems on this platform. If the tub wasn't properly secured or the washer was tilted significantly during a move, one or more shock absorbers can separate from their mounting point. Check that all four shocks are still properly connected at both ends before assuming a shock itself has failed — sometimes reseating a separated shock is all that's needed, though if it shows wear it's worth replacing regardless. How much vibration is normal, and how do I know it's actually the shocks? Some vibration during high-speed spin is normal, especially with an unbalanced load. But vibration strong enough to move the washer across the floor, or accompanied by a banging or knocking noise from inside the cabinet, points to a suspension problem rather than a simple unbalanced load. Try redistributing the laundry evenly in the drum and running the spin cycle again — if the shaking persists with a balanced load, inspect the shock absorbers for wear, cracking, or separation. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, mounting configuration, and damping performance of the original WH01X20826 shock absorber used in compatible GE, Hotpoint, Haier, Monogram, Café, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11130356 Washer Genuine Suspension Rod Kit Replaces Part Numbers: W11130356, W11027214, 4547230, W10594084, W10735787, W10821706, W10901058, W11033601, PD00042210, EAP12347543, AP6261900, PS12347543.

Read more less

WPW10547292 Genuine OEM Whirlpool Dryer Idler Pulley The WPW10547292 is a genuine Whirlpool OEM idler pulley assembly for Whirlpool, Maytag, and Kenmore dryers. This pulley sits to the left of the motor, just below the drum belt, and its job is to ride against the belt and keep constant tension on it as the motor turns — without that tension, the belt would sag, slip on the motor pulley, and fail to reliably turn the drum. The pulley wheel itself spins freely on a bearing mounted to a bracket, so as the belt moves, the pulley spins along with it under light load. Over time, the bearing inside the pulley wheel wears out, causing it to spin roughly, seize partially, or bind up entirely instead of turning freely. When that happens, the belt drags against a pulley that should be spinning smoothly with it, generating friction, heat, and noise. A worn idler pulley produces a very recognizable symptom: a persistent squeaking or squealing sound during operation that often gets more noticeable over time, and in more advanced cases, a drum that struggles to spin or doesn't spin at all, or a burning smell as the seized pulley drags against the belt. It directly replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, and LP16246. Quick Answer The WPW10547292 Genuine OEM Whirlpool Dryer Idler Pulley fixes Whirlpool, Maytag, and Kenmore dryers with a persistent squeaking or squealing noise during operation, a drum that struggles to spin, or a burning smell from a seized pulley dragging against the belt. Mounts to the left of the motor, below the belt. Replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, LP16246. Consider replacing the drum belt (8544742/WP8544742) at the same time — a seized idler pulley is a common cause of premature belt wear, and you'll already have the cabinet open. Common Problems This Part Fixes Persistent squeaking or squealing noise during operation Noise that gradually gets louder or more frequent over time Drum that struggles to spin, spins intermittently, or won't spin at all Burning smell coming from inside the dryer cabinet Pulley wheel that feels stiff, gritty, or seized when checked by hand Drive belt showing premature wear or fraying from dragging against a bound-up pulley Noise that stops and starts depending on drum rotation or load size Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer idler pulley directly replaces the following OEM and cross-reference part numbers: WPW10547292, W10547292, WPW10547292VP, AP6022817, 8547160, EAP11756154, PS11756154, AWP50878, PD00003590, LP16246 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select Whirlpool, Maytag, and Kenmore dryers, including model numbers such as: Whirlpool: WED7300XW0, WED7800XB0, WED8100BW0, WED8500BC0, WED8500BR0, WED8500BW0, WED8600YW0, WED8600YW1, 7MWGD7800XW0, 7MWGD8800AW0, 7MWGD8800AW1 Whirlpool (Y-prefix): YWED8000BW0, YWED8100BW0, YWED8200YW2, YWED8400YW2, YWED8500BC0, YWED8500BW0, YWED8800YC2, YWED8800YW2, YWED8900BC0, YWED8900BW0, YMEDB980BW0 Maytag: 7MMGDB850WL0, 7MMGDB950AG0, MEDB200VQ1, MEDB725BW0, MEDB800VB0, MEDB850WL1, MEDB850WR1 Kenmore: 110.78102310, 11067032600, 11067032601, 11067042600, 11067042601, 11067052600, 11067062600, 11067072600, 11067082600, 11067086600 Note: Whirlpool uses several different idler pulley designs across its dryer lineup, and they are NOT interchangeable. This WPW10547292 pulley is a separate part from the W10837240 pulley (used on Cabrio, Duet, and Bravos XL platforms) and the 279640 pulley (an older, differently-shaped design). Fitting the wrong pulley can result in a bracket that doesn't mount correctly or a wheel that doesn't align with your belt. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pulley fits your dryer. Key Features Genuine Whirlpool OEM part — factory-specified bearing and bracket design Maintains constant tension on the drive belt so it can turn the drum smoothly Resolves "squeaking or squealing noise," "drum won't spin," and "burning smell" symptoms caused by a worn or seized pulley bearing Complete wheel-and-bracket assembly — no need to source parts separately Direct drop-in replacement — mounts to the original bracket position with the same bolt Replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, and LP16246 Compatible with Whirlpool, Maytag, and Kenmore dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10547292 Part Type Dryer Idler Pulley Assembly (Wheel + Bracket) Condition Genuine OEM Brand Whirlpool Location Left of the motor, below the drum belt Function Maintains tension on the drive belt as it turns the drum Fuel Type Electric and gas dryers Companion Part 8544742 / WP8544742 drum belt (check/replace if pulley failed) Repair Difficulty Medium — requires some disassembly Quantity 1 idler pulley assembly Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — On Gas Models, Shut Off The Gas Supply Too Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas dryer, also close the gas shutoff valve before moving the cabinet. Wear work gloves. Remove the lint filter, then remove the screws along the top edge of the front panel and take the panel off. With the front open, locate the belt tensioner pulley — it sits to the left of the motor, just below the belt. Use a socket wrench with an extension to loosen the pulley's mounting bolt, then remove the old pulley assembly, releasing the belt from it as you go. Slide the new WPW10547292 assembly onto the mounting post, making sure the grooves line up correctly so the belt seats snugly against the wheel, then re-tighten the mounting bolt securely. Before closing everything up, spin the new pulley by hand to confirm it turns freely with no grinding or resistance, and inspect the belt for wear, glazing, or fraying — replace it as well if it shows any of these signs, since a worn belt will quickly wear out even a brand-new pulley. Reinstall the front panel and its screws, restore power, and run a short empty cycle listening for the squeak to confirm it's resolved. Tools needed: 1/4" nut driver, 3/8" socket wrench with extension, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer squeaks constantly. Is this definitely the idler pulley? It's one of the most common causes of a persistent squeak, especially if the noise is steady and present throughout the cycle rather than only at certain moments. The pulley's internal bearing wears out over years of use, and a worn bearing produces exactly this kind of ongoing squeal as it spins roughly instead of smoothly. If you can access the pulley and spin it by hand, feeling any grinding or stiffness confirms the diagnosis. Is this a hard repair, or can I do it myself? It's a moderate repair — you'll need to remove the front panel and access the area behind the motor, which some customers describe as needing to "pull the entire dryer apart" to reach the pulley. It's very doable with basic hand tools and some patience, but budget more time than a simple part swap, and expect to use a socket wrench with an extension to reach the mounting bolt in that tighter space. Should I replace the belt while I'm already in there? It's worth strongly considering. A seized or dragging pulley puts extra wear on the belt, so if your pulley failed from being seized rather than just noisy, the belt may already be showing damage. Since you'll already have the cabinet open and the belt exposed, inspecting it — and replacing it if it shows glazing, cracking, or fraying — saves you from repeating this same teardown again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original bearing design, bracket shape, and mounting configuration of the idler pulley assembly originally installed in your Whirlpool, Maytag, or Kenmore dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

MSWF Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Replaces Part Number: 1262070, AH1559689, EA1559689, MSWF3PK, WR02X12345, WR02X12801, WR02X13618, AP3997949, PS1559689.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP6-3705180 Dryer Idler Pulley Arm Replaces Part Numbers: WP6-3705180, 6-3705180, 1472858, 33001782, 33001840, AP6009860, PS11743033. Description: The Idler Pulley Arm is a Genuine OEM replacement part for Whirlpool dryers. As a connecting part, it works to route the drive belt and suspend the idler pulley. Mounted on a pivoting bracket, the durable arm positions the idler pulley to maintain proper belt tension over the lifter roll and drum. 🔧 WP6-3705180 Dryer Genuine OEM Idler Pulley Arm Get your dryer spinning smoothly again with the WP6-3705180 Genuine OEM Idler Pulley Arm, a reliable, factory-certified replacement designed to restore quiet and efficient drum rotation. This part keeps proper tension on the drum belt, preventing slippage, squeaks, and extended drying times. If your dryer is noisy, slow, or not spinning, this small part could be the big fix you need. ✅ Key Features: OEM Quality Guaranteed – Model: WP6-3705180 (Replaces 6-3705180) Heavy-Duty Construction – Handles high heat and constant friction Quiet & Smooth Performance – Eliminates squealing or grinding DIY-Friendly Installation – No special tools required Multi-Brand Fit – Works with Whirlpool, Maytag, Crosley & more 💡 Why Buy from Parts-O-Matic?At Parts-O-Matic, we specialize in genuine OEM appliance parts— With fast shipping, expert support, and a perfect fit guarantee, we help you fix it fast and fix it right. 🔄 Replaces Part Numbers: WP6-3705180, 6-3705180, 1472858, 33001782, 33001840, AP6009860, PS11743033. 🧰 Compatible Brands: Maytag Whirlpool Crosley Magic Chef Need help confirming compatibility? Message us—our experts are here to help!

Read more less

134101800 Washer Lid Lock Switch – Replacement for Frigidaire, Electrolux, Kenmore Product Overview This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. 120V, 60Hz, lid lock and switch assembly. Replaces Part Numbers This switch replaces part numbers 134101800, 131595100, 131675600, 3204390, 3204391, 3205646, 5303306138, 916791, AP2108159, PS648775. It matches original specifications for fit and performance in compatible top-load washers. Compatible Brands This lid lock switch is compatible with washers from Frigidaire, Electrolux, Kenmore, and Gibson. It fits many models built under these brands and used in U.S. and Canadian homes. Fixes the Following Issues Washer won’t start Lid lock error or flashing indicator Washer stops mid-cycle Broken or non-responsive lid switch Why Buy from Parts‑O‑Matic High-quality, tested aftermarket part Fast and free shipping across the U.S. Trusted by appliance repair pros and DIYers Easy returns and friendly customer support

Read more less

XPARTCO W10734521 Washer Clutch Slider Kit The XPARTCO W10734521 is an aftermarket replacement washer clutch slider kit compatible with a wide range of Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers. The clutch slider kit is part of the drive system that engages and disengages the inner tub from the gearcase — it's responsible for transitioning the washer between agitation and spin modes. The slider gear works together with the electromagnetic clutch and gearcase to move the inner tub during the wash and spin portions of every cycle. When the slider or its spring fails, the washer typically won't spin properly, won't agitate, makes grinding noise, or leaves clothes soaking wet at the end of a cycle. This kit includes the slider, spring support, 30mm spiral, and bolt. Slider dimensions: 2-7/8" outer diameter x 7/8" deep. Support spring: 1-5/8" outer diameter x 1-1/8" long. Spiral: 1-5/16" outer diameter. Bolt: 7/8" head diameter x 1" high. Construction is metal and plastic in black, white, and gray. Important: this is the slider kit only — it does NOT include the electromagnetic clutch (sold separately as W10754448). The current W10734521 part number supersedes the earlier W10006484, W10006494, W10275082, W10447975, and W10905025. It also replaces 3452506, AP5952873, EAP10060062, PD00025495, and PS10060062. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO W10734521 Washer Clutch Slider Kit fixes Whirlpool, Maytag, Kenmore, KitchenAid, and related HE top-load washers that won't spin or agitate properly, won't transition between cycle phases, leave clothes soaking wet, or make grinding noise during the spin cycle. Slider kit only — electromagnetic clutch (W10754448) is sold separately. Includes slider (2-7/8" OD), spring support (1-5/8" OD), 30mm spiral, and bolt. Replaces W10006484, W10006494, W10275082, W10447975, W10905025, 3452506, AP5952873, EAP10060062, PD00025495, PS10060062. Common Problems This Part Fixes Washer won't spin or spins very slowly — slider not engaging the gearcase for spin mode Washer won't agitate — slider not transitioning the drive system to agitation mode Clothes left soaking wet at the end of the cycle — incomplete spin Grinding, rattling, or clunking noise during the spin or agitation phase Washer fills and drains normally but never spins or agitates Worn or broken slider gear teeth visible on the drive assembly Weak or broken slider spring — washer drive losing positive engagement Repeated cycle interruptions in the spin or agitation portion of cycles What's in the Kit Part 1 Slider Gear 2-7/8" outer diameter x 7/8" deep · Slides over the drive assembly shaft to engage/disengage the gearcase for agitation and spin transitions · Install with the teeth facing outward Part 2 Spring Support 1-5/8" outer diameter x 1-1/8" long · Provides return tension for the slider · Replace whenever the gearcase or slider is replaced — spring can weaken over time Part 3 30mm Spiral 1-5/16" outer diameter · Spiral retaining component that holds the slider assembly together on the drive shaft Part 4 Bolt 7/8" head diameter x 1" high · Secures the assembly Replaces Part Numbers This clutch slider kit directly replaces the following OEM and cross-reference part numbers: W10734521, 3452506, W10006484, W10006494, W10275082, W10447975, AP5952873, AWP41487, EAP10060062, PD00025495, PS10060062. W10734521 is the current production part superseding W10006484, W10006494, W10275082, W10447975, and W10905025. Contact our support team with your model number if you need confirmation before ordering. Compatibility This clutch slider kit is compatible with select HE top-load washers from the following brands: Whirlpool top-load washers (Cabrio, WTW5000, WTW5500, WTW5700, WTW6000, WTW6200, WTW6400, WTW7000, WTW7120, WTW8000, WTW8200, WTW8500, WTW8700 series and related models) Maytag top-load washers (Bravos and Centennial series and related models) Kenmore / Sears top-load washers (Whirlpool-built — select 110-series and related models) KitchenAid top-load washers (select models) Amana top-load washers (select models) Crosley top-load washers (select models) Estate top-load washers (select models) Jenn-Air top-load washers (select models) Roper top-load washers (select models) Magic Chef top-load washers (select models) Admiral top-load washers (select models) Kirkland top-load washers (select models) Important — Slider Kit Only, NOT Clutch: This is the clutch slider kit (slider, spring, spiral, bolt) — it does not include the electromagnetic clutch assembly. The electromagnetic clutch is part number W10754448 and is sold separately. If you need both components, order each part separately. Many repair scenarios call for replacing both at the same time, since both wear together. Always verify your model number and confirm exactly which component has failed before ordering. Key Features Complete slider repair kit — slider, spring support, 30mm spiral, and bolt included as a matched set Works with the electromagnetic clutch and gearcase to drive the inner tub during agitation and spin modes Resolves "won't spin," "won't agitate," and "clothes left soaking wet" symptoms when the slider has worn or the spring has weakened Current production part number — supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 Slider: 2-7/8" outer diameter x 7/8" deep · Spring: 1-5/8" OD x 1-1/8"L · Spiral: 1-5/16" OD · Bolt: 7/8" head x 1"H Metal and plastic construction in black, white, and gray Important: slider kit only — electromagnetic clutch (W10754448) sold separately For full performance, replace all components in the kit together as a set Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 60–90 minutes with basic hand tools Product Specifications Part Number W10734521 Supersedes W10006484, W10006494, W10275082, W10447975, W10905025 Part Type Washer Clutch Slider Kit Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool platform) Includes 1x Slider, 1x Spring Support, 1x 30mm Spiral, 1x Bolt Slider Dimensions 2-7/8" Outer Diameter x 7/8" Deep Spring Support Dimensions 1-5/8" Outer Diameter x 1-1/8" Long Spiral Dimensions 1-5/16" Outer Diameter Bolt Dimensions 7/8" Head Diameter x 1" High Material Metal / Plastic Color Black / White / Gray Electromagnetic Clutch NOT included — see W10754448 (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, Kirkland Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect power and turn off the water supply before beginning. Place towels under the washer — some residual water may spill from hoses during disassembly. Wear work gloves to protect your hands. Unthread the hot and cold water supply hoses from the inlet valve ports. Disconnect the drain hose from the outlet port using channel-lock pliers to release the spring clamp. Carefully tip the washer onto its side or back on a padded surface to access the underside. Disconnect the wiring harnesses to the drive motor and pull the rotor free — be prepared for some resistance, as the permanent magnets in the rotor require some effort to remove. Use a small awl inserted between the slider gear teeth to release the spring retainer. With the retainer released, pull off the old spring and slider gear. Note the orientation of the slider — teeth facing outward. Install the new W10734521 components in sequence: slide the new slider gear onto the drive assembly shaft with teeth facing outward, install the new spring support and 30mm spiral, and secure with the new bolt. Reinstall the rotor (the magnets will pull it into place), reconnect the wiring harnesses, return the washer to upright, reconnect supply hoses and drain hose, restore power and water, and test the spin cycle for proper function. Tools needed: Phillips screwdriver, socket set, channel-lock pliers, small awl, padded surface for tipping, work gloves. Frequently Asked Questions What's the difference between W10734521 and W10754448? These are two different parts in the same drive system. The W10734521 is the clutch slider kit — it includes the slider gear, spring support, spiral, and bolt that physically engage/disengage the inner tub from the gearcase to transition between agitation and spin modes. The W10754448 is the electromagnetic clutch itself — the electrical component that drives the engagement. Both can fail independently, and many repair scenarios call for replacing both at the same time since they work together. Confirm exactly which component has failed before ordering, or order both if you're rebuilding the drive system as a full repair. My washer won't spin — is it the slider or something else? A washer that won't spin can have several causes: a failed slider kit, a failed electromagnetic clutch (W10754448), a damaged drive belt, a failed motor or rotor, a broken lid switch, or — on some models — a failed gearcase. The slider kit is one of the more common causes when the symptom is "fills and drains but won't spin" with no obvious noise or burning smell. Before replacing the slider, check that the lid latch strike (W11457841 on some models) is engaging properly, the drive belt is intact, and the motor is functioning. If those check out and the slider gear shows visible wear, missing teeth, or a stretched spring, the W10734521 kit is the right repair. Should I replace all parts in the kit together? Yes — for the kit to perform as designed, all components should be replaced as a matched set. The slider, spring support, spiral, and bolt all work together — if one is worn, the others have typically experienced the same load and wear. Reusing old components alongside new ones can cause premature failure of the new parts and a repeat repair. The W10734521 kit is priced and packaged for a complete replacement, so install all four pieces during your repair. What is the difference between W10734521 and the older part numbers it replaces? W10734521 is the current production version of this slider kit. It directly supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 — all of which were earlier OEM part numbers for variations of the same slider kit across production revisions. Whirlpool consolidated these into the W10734521 to streamline the parts catalog. If your washer's parts diagram shows any of these older numbers, the W10734521 is the correct current replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, gear profile, and drive engagement function of the original W10734521 clutch slider kit used in compatible Whirlpool, Maytag, Kenmore, and related HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH02X10363 Genuine OEM GE Washer Hub Nut The WH02X10363 is a genuine GE OEM hub nut for GE, Hotpoint, and select RCA and Kenmore top-load washers. This nut is what secures the wash basket to the transmission's drive spline, holding the entire tub assembly firmly attached to the drive system. Every time the washer agitates or spins, this single nut is what keeps the basket properly seated and aligned rather than shifting or working loose under that repeated mechanical load. Over years of use, or from overloading the washer with oversized loads, this nut can loosen or wear enough that the basket no longer sits securely. A failed or loose hub nut typically shows up as a basket that wobbles or feels loose, unusual noise during agitation or spin, or in more advanced cases, a basket that isn't properly engaging with the drive system at all. It directly replaces AP5793681, 3029784, and PS8757009. Quick Answer The WH02X10363 Genuine OEM GE Washer Hub Nut fixes GE, Hotpoint, RCA, and Kenmore top-load washers with a wobbling or loose-feeling basket, unusual noise during agitation or spin, or a basket that isn't securely engaging with the drive system. Replaces AP5793681, 3029784, PS8757009. This nut requires a very specific torque — GE's own guidance calls for a 90 ft-lb torque-limiting extension and a 1-5/16" (33mm) impact socket. Using a standard impact wrench without the torque limiter can damage both the new nut and the transmission. Common Problems This Part Fixes Wash basket that wobbles or feels loose Unusual noise during agitation or spin Basket that isn't properly engaging with the drive system Missing or broken hub nut Basket instability that worsens with larger or unbalanced loads Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hub nut directly replaces the following OEM and cross-reference part numbers: WH02X10363, 3029784, AGE1396433, AP5793681, EAP8757009, PD00046649, PS8757009. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hub nut is compatible with select GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, Café, and Kenmore washers built on the GE platform, including model numbers such as GHWN8350D0WS and GTW465ASN2WW. Note: Always verify your full model number before ordering, since GE uses different hub nut sizes and thread designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified thread and torque rating Secures the wash basket to the transmission drive spline Resolves "wobbling basket," "loose feel," and "unusual noise during agitation or spin" symptoms 1-5/16" (33mm) nut size Direct drop-in replacement — matches the original thread and fit Replaces AP5793681, 3029784, and PS8757009 Compatible with GE, Hotpoint, RCA, Haier, Monogram, Café, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH02X10363 Part Type Washer Hub Nut Condition Genuine OEM Brand GE Application Top-Load Washers Size 1-5/16" (33mm) Function Secures the wash basket to the transmission drive spline Required Torque 90 ft-lb (torque-limiting extension required) Thread Direction Reverse-threaded — tightens counter-clockwise Repair Difficulty Moderate to Hard — specialized tools required Quantity 1 hub nut Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Critical — Correct Torque Tool Required, And This Nut Threads Counter-Clockwise Unplug the washer before beginning. Wear work gloves and safety glasses. Remove the fabric softener dispenser to access the agitator/auger assembly. Use a screwdriver to puncture through the inner shaft of the auger, then twist clockwise until the auger releases — this step can be difficult, and you'll need to hold the basket steady to keep it from rotating while you work. Lift the auger out. Remove the 11mm bolt underneath, then lift out the base assembly to expose the hub nut. Per GE's own guidance, removing and installing this nut requires a 90 ft-lb torque-limiting extension (GE part WX05X10028) along with a 1-5/16" (33mm) impact socket (GE part WX05X10022). Using a standard impact wrench without the torque limiter risks over-torquing, which can damage both the new nut and the washer's transmission. Unthread the old 33mm hub nut — this can also be difficult, so be patient and keep the basket from rotating. To install the new WH02X10363, thread it on going counter-clockwise, since this nut is reverse-threaded — the opposite direction of a standard nut. Align the base with the spline shaft, set it into position, and reassemble in reverse order: reinstall the 11mm bolt, reinstall the auger, and reattach the fabric softener dispenser. Restore power and run a test cycle to confirm the basket is stable with no wobble or unusual noise. Tools needed: impact driver or wrench with 90 ft-lb torque-limiting extension, 1-5/16" (33mm) deep well or impact socket, 3/8" to 1/2" adapter, 11mm socket, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions Do I really need a special torque tool, or can I use a regular impact wrench? GE's own manufacturer guidance is explicit on this point: a 90 ft-lb torque-limiting extension must be used when removing or installing this hub nut to prevent damage to the nut and the transmission from over-torquing. A standard impact wrench alone can apply far more force than this nut and the transmission are designed to handle, so skipping the torque limiter risks turning a simple nut replacement into a much larger and more expensive transmission repair. Which direction does this nut turn to tighten? This nut is reverse-threaded, meaning it tightens by turning counter-clockwise — the opposite of a standard nut. This is an easy detail to miss if you're not expecting it, and turning it the wrong direction won't seat it correctly. Keep this in mind both when removing the old nut and installing the new one. My basket feels wobbly. Is this definitely the hub nut? It's a strong possibility, especially if the wobble has developed gradually or worsened after washing unusually large or unbalanced loads. Since this nut is what holds the entire basket assembly firmly attached to the transmission's drive spline, a loosened or worn nut directly translates into a basket that no longer sits securely. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original thread design, size, and torque rating of the hub nut originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11087376 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533. California Residents only WARNING: California’s Proposition 65 

Read more less